CG78-06B1A. Product Classification. Dimensions. Electrical Specifications. Environmental Specifications. General Specifications
|
|
|
- Osborne O’Brien’
- 5 years ago
- Views:
Transcription
1 CG78-06B1A SureGround Grounding Kit for 7/8 in coaxial cable OBSOLETE This product was discontinued on: October 1, 2013 Replaced By SG78-06B2A SureGround Grounding Kit for 7/8 in coaxial cable Brand Bonding Conductor Compatible Diameter, maximum Compatible Diameter, minimum SureGround Grounding kit 7/8 in mm 24 in mm in mm in Electrical Specifications Current Handling Tested to withstand 100,000 amps peak current surge Current Handling Test Method MIL-STD-1757 Grounding, Bonding and Shielding Test Method MIL-STD A Lightning Protection Test Method IEC Environmental Specifications Operating Temperature Storage Temperature Weatherproofing Method Grounding Kit Type Cable Type Brand Harmonized System (HS) Code -40 C to +85 C (-40 F to +185 F) -40 C to +80 C (-40 F to +176 F) Butyl and electric tape SureGround Grounding Kits Corrugated Smoothwall SureGround (Coaxial cable and other coaxial electric conductors) page 1 of 5 most current information. Revised: September 13, 2017
2 CG78-06B1A Bonding Conductor Material Bonding Conductor Wire Size Bonding Conductor Jacketing Material Grounding Strap Material Includes Locking Bail Material Lug Attachment Lug Type Rivet Material Copper 6 gauge PVC Tinned copper Grounding kit Hardware Lug One roll of 2 in PVC tape One roll of 24 in butyl rubber tape Stainless steel Factory attached One-hole lug Tinned copper Blowing Rain Test Method MIL-STD-810, Method 506 Corrosion Test Method MIL-STD-1344, Method 1001 Freezing Rain/Icing Test Method MIL-STD-810, Method 521 Humidity Test Method MIL-STD-1344, Method 1002 Immersion Test Method IEC 60529:2001, IP68 Thread Size 3/8 in M10 UV Resistance Test Method MIL-STD-810, Method 505 Vibration Test Method MIL-STD-202, Method mm 9.0 in 57.2 mm 2.3 in 0.62 kg 1.37 lb mm 8.5 in Included Products in PVC Tape, 20 ft Butyl Rubber Tape, 24 in * Footnotes Grounding, Bonding and Shielding Test Method Military Standard for Grounding, Bonding, and Shielding: Bond Resistance Requirement of a Maximum dc resistance of ohm Lightning Protection Test Method Protection Against Lightning Electromagnetic Impulse, Table 1 Protection Level III IV, page 2 of 5 most current information. Revised: September 13, 2017
3 in PVC Tape, 20 ft Weatherproofing tape 6.10 m ft 1-1/4 in 1-5/8 in 1/2 in 1/4 in 2-1/4 in 3/8 in 5/8 in 7/8 in mm 2.00 in Application Provides additional moisture seal for cable connections Applications per Kit Four 1/2 in 1/2 in Four 1/2 in 7/8 in to device One 1/2 in 2-1/4 in Two 1/2 in 7/8 in Material Type PVC tape UV Resistance Test Method PVC tape test method UL 510, ASTM D1000 Weather Resistance Test Method 04AS MIL-STD-1344A, Method cm 2.0 in 0.08 kg 0.19 lb Regulatory Compliance/Certifications Agency Classification ISO 9001:2008 Designed, manufactured and/or distributed under this quality management system page 3 of 5
4 Butyl Rubber Tape, 24 in Weatherproofing tape mm in 1-1/4 in 1-5/8 in 1/2 in 1/4 in 2-1/4 in 3/8 in 5/8 in 7/8 in mm 2.50 in Application Applications per Kit Material Type UV Resistance Test Method Provides additional moisture seal for cable connections One 1/2 in 2-1/4 in One 1/2 in 7/8 in One 1/2 in 7/8 in to device Two 1/2 in 1/2 in Butyl rubber tape UV Resistance, minimum with no degradation =1000 hours Butyl test method in QUV weatherometer cycle of 8 hours UV at 150 F then 4 hours of condensation at 104 F Weather Resistance Test Method 04AS MIL-STD-1344A, Method cm 1.0 in 0.17 kg 0.37 lb 69.9 mm 2.8 in page 4 of 5
5 Regulatory Compliance/Certifications Agency Classification RoHS 2011/65/EU Compliant China RoHS SJ/T Below Maximum Concentration Value (MCV) ISO 9001:2008 Designed, manufactured and/or distributed under this quality management system page 5 of 5
SGL7-06B2. Product Classification. Dimensions. Electrical Specifications. Environmental Specifications. General Specifications
SGL7-06B2 SureGround Grounding Kit for 1-5/8 in corrugated coaxial cable OBSOLETE Replaced By SG158-06B2A SureGround Grounding Kit for 1-5/8 in coaxial cable Brand Bonding Conductor Cable Jacketing Removal,
Construction Materials. Dimensions. Environmental Specifications. General Specifications. Regulatory Compliance/Certifications.
Construction Materials Fiber Type Total Fibers, quantity 2 Armor Type Furcation Color Jacket Color HFT412-2S29F-15 HELIAX FiberFeed Hybrid Cable Assembly, 6-OVP box to RRU, UL Type TC-ER, 4 power conductors
Amphenol RF- SMA Connector Series
Page 1 of 8 enter part number Products 7/16 1.0/2.3 1.6/5.6 AMC BNC / RP-BNC C FAKRA SMB FME HN MCX Mini-UHF Mini 75 Ohm SMB MMCX Precision (APC) QDS QMA QWS SC SlimLine BNC SMA / RP-SMA SMB SMC SMP TNC
Heat-Shrinkable Tubing
CPO 2:1 Shrink Ratio Thin-Wall Tubing, Non-Lined Flame-retardant, cross-linked polyolefin Continuous operating temperature: -55 C to 135 C Shrink temperature of 120 C Meets UL and CSA standards; MIL-DTL-23053/5
ENGLISH Datasheet Platinum Resistance Pt100 4 wire class B Resistance Thermometer with DIN B Head
ENGLISH Datasheet Platinum Resistance Pt100 4 wire class B Resistance Thermometer with DIN B Head With stainless steel plug (no thread) Pt100 probe with DIN B terminal head Class B, 4 wire connection Various
Termco Heatshrink.
Termco Heatshrink Thin Wall Tubing (Flame Retardant) Clear Thin Wall Tubing Green/Yellow Thin Wall Tubing Dual Wall Tubing Medium Wall Tubing Cable End Caps Heat Shrink Miniature End Cap Heat Shrinkable
UNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 260526 - GROUNDING AND BONDING FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract apply to this Section. 1.2 SUMMARY A. This Section
O Coaxial/Fiber/Microduct Hybrid Buried Cable. Serves businesses in a new commercial serving area. Mitigates future cost of fiber installation
Product Classification E 2 O E2O540JCASS-24CT 24CT MICFIBR-12.7MB DUCT E 2 O Coaxial/Fiber/Microduct Hybrid Buried Cable E 2 O is a solution that enables service providers the ability to bridge HFC networks
ENGLISH. Datasheet. RS single element: Single 4 wire element, allowing connection to any Pt100 2, 3 or 4 wire instrument
Datasheet ENGLISH Platinum Resistance Thermometer Pt100 Outdoor/Cold Store Temperature Sensors IP67 Weatherproof Housing, 4 wire single or dual element, or 4-20mA option Weatherproof IP67 rated wall mounting
Table of Contents. Version 1.0. Specifications 2 Technical Specifications 2 Colors and Lumen Count 2. Packaging 6
Version 1.0 Table of Contents Specifications 2 Technical Specifications 2 Colors and Lumen Count 2 Physical Specifications 3 Part Number Naming Convention 3 Packaging 6 Mounting Hardware 7-8 Standard 7
Conductor Shield A combination of semi-conducting tape and extruded thermosetting semi-conducting material meeting UL 1309, IEEE 1580 and UL1072.
37-105VFD MMV-VFD Power Cable Three : kv - 15kV 133% Level Rated 90 C s (3) Soft annealed flexible stranded tinned copper per IEEE 150 Table 11. Extruded thermosetting 90 C Ethylene Propylene Rubber (EPR),
Welding Accessories
Welding Accessories www.airliquide.ca 1-800-817-7697 Welding Accessories BLUESHIELD Welding Cables Blueshield Welding Cables: Excellent flexibility (stays flexible at -50 C) Abrasion resistant Oil, solvent
SECTION PARK NON-SEGREGATED BUS SPECIFICATION
Page 1 of 5 SECTION ------- PARK NON-SEGREGATED BUS SPECIFICATION 1.0 SCOPE 1.1. This specification describes assemblies of 600V, 5Kv and 15Kv non-segregated bus duct, which will be installed indoors and
/DB O-002-DF-HY-F02NS/8W002/1X24AWG
LightScope ZWP Fiber + Tone Wire Outdoor Drop Cable, 1 12 fiber Arid Core construction, central loose tube Product Classification Portfolio Brand Product Type Regional Availability CommScope LightScope
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD. ANSI/SCTE (Formerly IPS SP 100)
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 15 2006 (Formerly IPS SP 100) Specification for Trunk, Feeder and Distribution Coaxial Cable NOTICE The Society
Product Warranty Every VERSABAR product has been carefully inspected during manufacturing, and prior to shipment. We guarantee to correct any defect called to our attention in writing within six months
Tip Jacks. Johnson Components P.O. Box 1732 Waseca, MN Fax:
.060" (1.5 mm) Shrouded Tip Jack (Solder or Crimp) 5.060" (1.5 mm) Uninsulated Tip Jack (Solder or Crimp) 5.060 (1.50) Shrouded Tip Jack (Solder or Crimp) 5.060 (1.50) Uninsulated Tip Jack (Solder or Crimp)
Flame-retardant, cross-linked polyolefin. Shrink temperature of 120 C. Cat. No.*
2:1 Shrink Ratio CPO Series Thin-Wall Tubing, Non-Lined CATALOGUE NUMBER CONSTRUCTION Final Series Colour ft Order No. CPO63 + 0 + C = CPO63-0-C Available Colours 0 Black 5 Green C Clear 6 Blue 2 Red 9
Multijacketed Tubing, Single-Jacketed Tubing, and Insulated Tubing
www.swagelok.com Multijacketed Tubing, Single-Jacketed Tubing, and Insulated Tubing Features 1/4 to in. and 6 to 12 tubing sizes available in 316/316L stainless steel and copper Seamless and welded tubing
Pt100 (100 0 C) to IEC 751, Class B, 4 wire 3.0, 4.0, 4.5 or 6.0mm diameter 316 stainless steel sheath.
Datasheet Platinum Resistance Thermometer Pt100 Industrial Sensor Probe, Class B Available in 3.0, 4.0, 4.5 or 6.0mm diameter x Various probe lengths ENGLISH Multipurpose Pt100 Probe to IEC751 Class B,
Platinum Resistance Pt100 Autoclave Drain Probe, 4 Wire Compatible with most common makes of Autoclaves
ENGLISH Datasheet Platinum Resistance Pt100 Autoclave Drain Probe, 4 Wire Compatible with most common makes of Autoclaves Pt100 Autoclave & steriliser drain temperature probe For use to monitor the fluid
Section ARMORED MEDIUM VOLTAGE CABLES SHIELDED 3 CONDUCTOR POWER CABLE - INTERLOCKED ARMOR
PART 1 - GENERAL Section 26 05 15 SHIELDED 3 CONDUCTOR POWER CABLE - INTERLOCKED ARMOR 1.1 Cable shall be 15 kv, shielded, three conductor with ground, stranded copper, with continuously welded and corrugated
ENGLISH Datasheet Platinum Resistance Pt1000 Class B Sensor with Teflon insulated lead
ENGLISH Datasheet Platinum Resistance Pt1000 Class B Sensor with Teflon insulated lead (Image shows 4 wire) Pt1000 element to IEC 751 Class B 2 wire configuration Temperature range -50 C to + 200 C Pt1000
150 mm. 1/8 BSPP brass male compression fitting with locknut included
ENGLISH Datasheet Platinum Resistance PT100 Flat Tip Probe 4mm diameter x 150mm long 2 wire with 1 metre flying lead, complete with 1/8 BSP compression fitting & locknut 4mm 25mm 5.5/6mm(max) 150 mm General
Datasheet Platinum Resistance Pt100 Dual Element Industrial Sensor Probe 6mm diameter x 150mm or 250mm probe lengths
Datasheet Platinum Resistance Pt100 Dual Element Industrial Sensor Probe 6mm diameter x 150mm or 250mm probe lengths ENGLISH Duplex PRT s with two independent PT100 detectors inside tip of probe. This
DESIGN GUIDELINES WIRING AND CONDUITS PAGE 1 of 7
DESIGN GUIDELINES WIRING AND CONDUITS PAGE 1 of 7 1.1. REFERENCE STANDARDS 1.1.1. Publications listed below (including amendments, addenda, revisions, supplements and errata) form a part of this specification
Metal Framing Channels Overview
New Trivalent Galv-Krom Finish Is RoHS Compliant Thomas & Betts is proud to introduce the new and improved Trivalent Galv-Krom finish. Galv-Krom finish is a combination of.5 mils electro-plated Zinc and
3M Cold Shrink Joint, SC145-II/SS145-II
3M Cold Shrink Joint, SC145-II/SS145-II Data Sheet June 2011 Description Features 3M Cold Shrink Joint, SC145-II/SS145-II meets requirements of IEC60840-2004 and GB11017.3 standards. Ideal electrode design
CONDUITS AND FITTINGS
CONDUIT AND FITTINGS Rigid Steel Conduit 3801 Rigid PVC Conduit 3803 HDPE Conduit 3803 Flexible Non Metallic Liquid Tight Conduit Type LFNC-B 3804 PVC Coated Urethane Lined Galvanized Rigid Steel Conduit
HS h e n EU omplia t 2002 / 9 5 / C
9 57-30500 0 0 E U 2 C A mp hen 2/ 5 / E omplia Ro HS ol C nt hen z n She 57-30360 DE-09P & DE-09S Standards: UL File: E119881 Connectors according to MIL C24308 SPECIFICATIONS : MATERIALS AND Shells Steel
ENGLISH. 1metre 7/.02mm Teflon insulated twin twisted lead
Datasheet Platinum Resistance Pt100 Sheathed Thin Film Strip Sensor 2 wire sensor sheathed in a thin stainless steel shim body ideal for surface measurement ENGLISH Sheathed Pt100 element in a thin, flat
PFC-304L12F. Product Classification. Standards And Qualifications. General Specifications. Construction Materials. Dimensions. Physical Specifications
Powered Fiber Cable, OM3, 4 Fibers, Indoor/Outdoor, 12AWG Conductor, feet Easy peel, stranded conductors for maximum cable flexibility and rapid access Polarization indentation along one side of the cable
Essex County College - West Essex Campus Addition And Renovations dlb # / 11-14
SECTION 270526 - GROUNDING AND BONDING FOR COMMUNICATIONS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
Platinum Resistance Thermometer Pt100 Precision Probe - High accuracy platinum resistance thermometer probe, 6mm diameter x 250mm
Datasheet ENGLISH Platinum Resistance Thermometer Pt100 Precision Probe - High accuracy platinum resistance thermometer probe, 6mm diameter x 250mm Precision Pt100 sensor offering high accuracy over the
Flexible Conduit Systems
Flexible Conduit Systems WHEN SAFETY MATTERS THERE S ONLY ONE CHOICE Complies to Australian & New Zealand Standards The Hi-Flex range of flexible conduit & fittings includes products tested to comply with
Mining Products. Jacketing and Insulating Tapes Trailing Cable Splice Kits High Voltage Splice and Termination Kits Cable Repair Tape Special Items
Jacketing and Insulating Tapes Trailing Cable Splice Kits High Voltage Splice and Termination Kits Cable Repair Tape Special Items Jacketing and Insulating Tapes Mining Products NEW PLYTUFF - F/R PVC Jacketing
Mining Products Jacketing and Insulating Tapes Trailing Cable Splice Kits High Voltage Splice and Termination Kits Cable Repair Tape Special Items Fon
Jacketing and Insulating Tapes Trailing Cable Splice Kits High Voltage Splice and Termination Kits Cable Repair Tape Special Items Jacketing and Insulating Tapes NEW PLYTUFF - F/R PVC Jacketing Tape PVC
CHAPTER 11 CONDUITS AND FITTINGS
CONDUITS AND FITTINGS CHAPTER 11 CONDUITS AND FITTINGS The standards and requirements for conduits and fittings used for traffic control signal and lighting systems are presented in this chapter. 11.1
Mineral Insulated Platinum Resistance Thermometer PT100 Sensor - Available in 3mm or 6mm diameter x 150mm or 250mm probe lengths
Datasheet ENGLISH Mineral Insulated Platinum Resistance Thermometer PT100 Sensor - Available in 3mm or 6mm diameter x 150mm or 250mm probe lengths High temperature, rugged, flexible Pt100 probe Suitable
NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 27 0526 - TECHNOLOGY GROUNDING SYSTEM PART 1 - GENERAL 1.1 RELATED DOCUMENT A. Drawing and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specifications,
Bundling, Insulating and Sealing Products
Product Facts Plastic cable wrap provides an easy way to bundle cable, wire, tubing or hoses Helps protect bundles against abrasion caused by vibration Coiled wrap allows wiring harness breakouts Nylon
SMP Coaxial Connectors Update
SMP Coaxial Connectors 2005 Update SV Microwave has introduced a complete line of SMP connectors which conform to DSCC 94007, 94008 and MIL-STD-348 specifications. SMP connectors provide microwave performance
M16 M20 M25 M207 M51 M100 M200
Metal Film Fixed Resistor Specifications Per IEC 60115-1 MIL-R-10509 d L H D Features Conformal multi-layer coating Color code per MIL & EIA standards Special tin-plated electrolytic copper lead wire Products
Table of Contents. Version 5.0. Specifications 2-4 Technical Specifications 2 Physical Specifications 3
Version 5.0 Table of Contents Specifications 2-4 Technical Specifications 2 Physical Specifications 3 Part Number Naming 4 Mounting Hardware 9-10 Standard 9 Plastic 9 Spring Clip 10 Flexible 10 Connectors
NYULMC AMBULATORY CARE CENTER FIT-OUT PHASE 1 Perkins & Will Architects PC 222 E 41st ST, NYC Project: Issued for GMP March 15, 2017
SECTION 27 05 26 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
Heavy Wall Heat Shrinkable Tubing 5-7. Flame Retardant Heavy Wall Heat Shrinkable Tubing 8. Heat Shrinkable Ends Caps 9
Heavy Wall Heat Shrinkable Tubing 5-7 Flame Retardant Heavy Wall Heat Shrinkable Tubing 8 Heat Shrinkable Ends Caps 9 Heat Shrinkable Breakout Boots 10 Shrink Ratio 3:1 Shrink-Kon Heavy Wall Heat Shrinkable
Fig. 1 - Standard Clevis Hanger
Revision 10/24/2007 Fig. 1 - Standard Clevis Hanger Component of State of California OSHPD Approved Seismic Restraints System Size Range Size 1/2" thru 36" pipe. Function Recommended for the suspension
Specifications: Ice point resistance: Fundamental interval (0 C to 100 C): 38.5Ω (nominal)
ENGLISH Datasheet Platinum Resistance Pt100 Wire-Wound Detector Elements Pt100 platinum resistance thermometer elements in a choice of sizes single & dual element Pt100 elements to IEC 60751 Class A or
Table of Contents. Version 2.0. Specifications 2-4 Technical Specifications 2-3 Physical Specifications 3-4
Version 2.0 Table of Contents Specifications 2-4 Technical Specifications 2-3 Physical Specifications 3-4 Part Number Naming 4 Connectors 5-8 Seamless 5 Submersible Seamless 6 Snap 7 Barrel 8 Mounting
SECTION MEDIUM-VOLTAGE CABLES PART 1 GENERAL
SECTION 260513 - MEDIUM-VOLTAGE CABLES PART 1 GENERAL 1.1 SECTION INCLUDES A. Medium voltage cable. B. Cable terminations. C. This specification describes single conductor EPR (Ethylene-propylene-rubber)
Pre-Insulated Tubing Bundles
www.swagelok.com Pre-Insulated Tubing undles Electric-Traced and Steam-Traced Features Simplified field installation 1/8 to 3/4 in. and 6 to 12 mm seamless or welded tubing sizes 316 / 316L stainless steel,
Wind Power Solutions. Company Registration No: Vat Registration No.:
Wind Power Solutions Foundation Grounding and Construction, Bonding, Power Connections, Surge Protection, and Lightning Protection ERICO offers a complete range of foundation grounding and construction,
ENGLISH Datasheet Platinum Resistance Pt100 & Pt1000 Thin Film Detectors Platinum Sensing Resistors Thin Film (Pt100 & Pt1000 Ohm)
ENGLISH Datasheet Platinum Resistance Pt100 & Pt1000 Thin Film Detectors Platinum Sensing Resistors Thin Film (Pt100 & Pt1000 Ohm) Pt100 Elements, Thin Film (100 Ohm) Pt100 elements to IEC751 Class A,
AMS-Military Grade Heat Shrinkable Wire Identification Sleeves
MS-VLA MS-VLA(C) AMS-Military Grade Heat Shrinkable Wire Identification Sleeves Description MSVLA series is the military grade cable and wire identification sleeves, which is made of cross-linked environmentally
Ribbon Cable connector Compliant with MIL Standard
Ribbon Cable connector Compliant with MIL Standard HIF3B Series Features 1. Product Compliant with MIL Standard HIF3B series has been developed as a product compliant with MIL standard, and used for wide
SECTION PART 1 GENERAL
SECTION 16060 GROUNDING AND BONDING PART 1 GENERAL 1.1 SUMMARY A. Section Includes: Grounding of electrical systems and equipment and basic requirements for ground for equipment, circuits, and systems.
Title: YALE OFFICE OF FACILITIES PROCEDURE MANUAL Chapter: 01 - Yale Design Standard Division: Electrical Standards
Change History Date Description of Change Pages / Sections Modified Change Approver Initials 6/15/16 Updated division section from 16124 to 2605 - mgl44 13, removed references to other section 10/17/14
3M Vinyl Electrical Tapes Tapes to help power through your toughest jobs.
3M Vinyl Electrical Tapes Tapes to help power through your toughest jobs. 3M Electrical Solutions Longstanding professional grade. From connectors to terminals to protective coatings, we have the right
DMS CONDUIT EFFECTIVE DATE: APRIL
DMS - 11030 EFFECTIVE DATE: APRIL 2014 11030.1. Description. This Specification governs the materials, composition, quality, sampling, and testing of electrical conduit. 11030.2. Units of Measurements.
NATIONAL DISTRIBUTOR OF BROADBAND PRODUCTS.
NATIONAL DISTRIBUTOR OF BROADBAND PRODUCTS Why Consider CPS? CPS is now part of the Genuine Cable Group Extensive Logistical Footprint Improved price stability Lower purchasing costs Decrease overall project
LIGHTNING PROTECTION SYSTEM EARTHING SYSTEM ELECTRICAL ACCESSORIES
LIGHTNING PROTECTION SYSTEM EARTHING SYSTEM ELECTRICAL ACCESSORIES AIR TERMINAL AIR TERMINAL FIXING BASE (flat) Material Aluminium / Copper Model Al-300-16 / Cu-300-16 Model Al-16 / GM-16 Diameter 16mm
TOTAL PIPING SOLUTIONS, INC. Quick Cam. Rapid Seal Repair Clamp. Patent Pending Technical Specifications
TOTAL PIPING SOLUTIONS, INC. Quick Cam Rapid Seal Repair Clamp Technical Specifications Rev B July 2017 1. Pressure Rating: Quick Cam Rapid Seal Repair Clamps by when properly installed are capable of
A LIGHTWEIGHT SOLUTION FOR SHIELDING AND CONDUCTING
A LIGHTWEIGHT SOLUTION FOR SHIELDING AND CONDUCTING EMI Shielding ARACON fibers braided into a shield or sock offer superior performance against electromagnetic interference. Advantages include: More uniform
MESP TECHNICAL SPECIFICATION FOR ELECTRIC CABLE 70mm 2 FLEXIBLE TINNED COPPER CONDUCTOR 3.3kV EPR INSULATED WITHOUT METALLIC SCREEN
Engineering Specification Electrical Networks MESP 030000-04 TECHNICAL SPECIFICATION FOR ELECTRIC CABLE 70mm 2 FLEXIBLE TINNED COPPER CONDUCTOR 3.3kV EPR INSULATED WITHOUT METALLIC SCREEN Version: 1 Issued:
Type 1 Machine Cable. Oxygen free tinned annealed copper wire interwoven with high tensile poly-yarn
Mining Cable Type 1 Machine Cable Application: Typically used for interconnection of control boxes or motors on non-mobile or fixed apparatus. Used when exposure to heat is not an issue and where added
Highly flexible, screened control cable with PVC insulation and PVC inner and outer sheath - certified
Highly flexible, screened control cable with PVC insulation and PVC inner and outer sheath - certified - Screened power and control cable for versatile use in power chains with UL/cUL AWM certification.
SafeX110 Single Core Flexible Tinned Copper Cable
LSZH 110 C Flexible SafeX110 Single Core Flexible Tinned Copper Cable Application: Wiring of switchboards, control, general wiring, instrumentation and communication systems. Used where low smoke, zero
Article-No. Type. All dimensions in mm. Subject to technical changes. Other dimensions, reel lengths or colours available on request.
4.4 Installation Devices HelaTape HellermannTyton offers a wide range of PVC and rubber tapes for sealing, insulation and bundling of cable and conduits. PVC based tapes are designed for low voltage applications
PERFORMANCE SPECIFICATION SHEET
INCH-POUND MIL-PRF-31031/41 10 March 2008 PERFORMANCE SPECIFICATION SHEET CONNECTOR, ELECTRICAL, RECEPTACLE, RADIO FREQUENCY, HIGH RELIABILITY, COAXIAL, SERIES BMZ, CONTACT, FOR FLEXIBLE CABLE This specification
Electrical Insulating Tapes
Electrical Insulating Tapes Energy, Mining, Industrial and Contractors applications LV and MV electrical jointing and termination applications Adhesive or Self-amalgamating UV resistant Cold and weather
A. The work consists of furnishing a Chiller Noise Reduction System as listed in the specifications.
SECTION 32 31 14 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply
nicrom e l e c t r o n i c
G E N E R A L High Performance Thick Film Resistors C A T A L O G 3 Nicrom Electronic Via Roncaglia CH - 6883 Novazzano SWITZERLAND Phone : ++4 () 9 68 99 86 Fax : ++4 () 9 68 99 86 info@nicrom-electronic.com
GREAT PRODUCTS GREAT PEOPLE GREAT SERVICE
Cathodic Protection The Contractors Choice GREAT PRODUCTS GREAT PEOPLE GREAT SERVICE thermoweld the Contractors Choice Continental Industries, Inc. is: A Sales and Customer Driven Company Founded in 1958
SPECIFICATIONS FOR Gas-to-Cable termination
Product GSM-145 1.0 APPLICATION: Gas-to-cable termination is a part of high voltage gas insulated indoor switchgear equipment. The component is intended for a high voltage system of 132 kv (AC), 50 Hz.
15~35KV Termination Kit
15~35KV Termination Kit Luyon Corporation 21221 Western Ave., #210 Torrance, CA 90501, U.S.A. Advantages of Silicone Rubber Power Cable Accessories Feature of silicone rubber: Silicone rubber is a unique
ENGINEERING SPECIFICATION EE SPEC
/. Company Directive ENGINEERING SPECIFICATION EE SPEC : 84/1 Relating to Surge Arresters EE SPEC : 84/1 20 December 2013-1 of 7 - IMPLEMENTATION PLAN Introduction This document defines the surge arresters
Reenterable PST Dome Closure
Reenterable PST Dome Closure Technical Report September 1999 80-6111-6055-9-A 1 2 Contents: 1.0 Product Description... 4 1.1 Kit Contents... 4 1.2 Material Composition... 5 1.3 Closure Capacity... 6 2.0
Highly flexible, screened control cable with PVC insulation and PVC inner and outer sheath - certified
Highly flexible, screened control cable with PVC insulation and PVC inner and outer sheath - certified - Screened power and control cable for versatile use in power chains with UL/cUL AWM certification.
31-SDMS-03 REV. 01 SPECIFICATIONS FOR
31-SDMS-03 REV. 01 SPECIFICATIONS FOR LOW VOLTAGE CABINET FOR POLE MOUNTED TRANSFORMER This specification is property of SEC and subject to change or modification without any notice CONTENTS Clause Description
solutions HIGH DENSITY CONNECTORS Custom designed Contact arrangements
Custom designed HIGH DENSITY CONNECTORS NANO-D PITCH As the need for increased miniaturisation is becoming ever greater, AXON has developed an ultra-high density solution within the existing micro connector
A. Product Data shall be provided for each type of product indicated.
32 31 13 CHAIN LINK FENCES AND GATES SECTION 1 GENERAL 1.1 SUMMARY This Section includes the following: 1. Chain Link Fences 2. Gates for Chain Link Fences. See electrical specifications for electrical
TUFF-SEAL RSF SERIES ALUMINUM CORD GRIPS. Toll Free Fax RSF Series Aluminum Flat Cable Cord Grips G 16
TUFF-SEAL RSF SERIES ALUMINUM CORD RIPS RSF Series Aluminum Flat Cable Cord rips Tuff Seal RSF Cord rips are specially designed for heavy-duty, flat cable or festoon system applications. Unique to the
SECTION 7.3 TECHNICAL SPECIFICATION OF POWER CABLES & CONDUCTOR
SECTION 7.3 TECHNICAL SPECIFICATION OF POWER CABLES & CONDUCTOR 458 7.3.1 11 KV Cables 7.3.1.1 General Where a Manufacturer s Standard or a national Standard equal to or better than the appropriate specified
Effective Date: Revision #: 1. Section K: Miscellaneous. Casing Insulators/ Stainless Steel. Polyethylene Encasement.
K 1 K 2 K 3 K 4 K 5 K 6 K 7 K 8 K 9 Casing Insulators/ Stainless Steel Polyethylene Encasement Manhole Inserts Pipe Saddle Support/ Valve Vaults/ Adjustable Cylindrical Wall Seals & Line Sleeves Metal
Product Datasheet. Fire Hose Reel (Page 3)
Product Datasheet Fire (Page 2) Fire Hose Reel (Page 3) Flush Type Hose Reel Cabinet (Page 4) GRP Fire cabinets are used for indoor and outdoor application with weatherproof and antistatic properties,
Solutions for Electronic Specialty Markets (ESM)
M Worldwide : United States : Electronics Manufacturing Solutions for Electronic Specialty Markets (ESM) Product Catalog for Electronic Specialty Markets M Electronic Specialty Markets - New Product Releases
Platinum Resistance Pt100 & Pt1000 Silicone Patch Sensors Element Encapsulated in A Silicone Rubber Patch with Self-Adhesive Aluminium Foil Backing
Datasheet ENGLISH Platinum Resistance Pt100 & Pt1000 Silicone Patch Sensors Element Encapsulated in A Silicone Rubber Patch with Self-Adhesive Aluminium Foil Backing Pt100 Patch Sensor (100 Ω Ohms @ 0
Permitting and Inspecting PV Systems. PV Codes and Standards 101. Photovoltaic System Basics
Permitting and Inspecting PV Systems Presented by Bill Brooks, PE Brooks Engineering PV Codes and Standards 101 What are the applicable codes and standards for PV systems? Electrical codes - NEC Article
Halogen Free Environmentally Friendly Heat Shrinkable Wire Identification Sleeves
MSVLU MSVLU(C) Halogen Free Environmentally Friendly Heat Shrinkable Wire Identification Sleeves Description MSVLU series is halogen free, environmentally friendly, heat shrinkable identification sleeves.
Clark Public Utilities
Clark Public Utilities TECHNICAL SPECIFICATIONS 15KV MEDIUM VOLTAGE 1000 MCM AL URD CABLE 175 MIL EPR FEBRUARY 1994 REVISED MAY 1996 REVISED JUNE 2001 REVISED MARCH 2002 REVISED MARCH 2005 REVISED MAY
1,35 1,0 0,6. Scale - 6:1
Dimensions: [mm] Recommended Land Pattern: [mm] 3 4 0,5 0,6 1,5 O 0,65 +0,1-0,0 0,8 1 2 0,4 1 4,7 2 3 4 2,2 1,6 4,05 1 3,5 Scale - 6:1 1,0 1,35 Schematic: 3,9 ±0,15 h 0,1 ref. 0,5 0,6 1 2 2,9 3,55 3 4
VN Series Floor Scale Instruction Manual
99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com VN Series Floor Scale Instruction Manual VN Series Floor Scale EN-1 INTRODUCTION
PERFORMANCE SPECIFICATION SHEET
INCH-POUND 18 April 2018 SUPERSEDING w/amendment 2 15 July 2016 PERFORMANCE SPECIFICATION SHEET CONNECTORS, RECEPTACLES, ELECTRICAL, COAXIAL, RADIO FREQUENCY, SERIES SMA, (UNCABLED), FEMALE, PRINTED CIRCUIT,
Table of Contents. Version 5.0
Version 5.0 Table of Contents Vivid S 160 Static 2-11 Specifications Technical Specifications 3-4 Epistar 5 Nichia 5 Testing Certifications 6 Fixture Testing 6 Photometric Data 7 Charts 8-11 Vivid S 160
SMA SERIES COAXIAL CONNECTORS
General R Reference Standards MIL-PRF-3912 MIL-DTL-83517 MIL-STD-348 (Interface) IEC 6169-15 CECC 12211 Materials Bodies and nuts Contacts Insulators Gaskets Crimp ferrules Non-magnetic stainless steel
DETAIL SPECIFICATION SHEET CABLE, ELECTRICAL, TYPE LSC5FS (INCLUDING VARIATIONS LSC5FSW, LSC5OS, AND LSC5OSW)
INCH-POUND MIL-DTL-24643/59 9 September 2005 DETAIL SPECIFICATION SHEET CABLE, ELECTRICAL, TYPE LSC5FS (INCLUDING VARIATIONS LSC5FSW, LSC5OS, AND LSC5OSW) This specification is approved for use by all
Extended-Frequency SMA Connectors
Extended-Frequency SM Connectors Extended-Frequency SM Connectors This brochure introduces two new series of connectors that extend SM performance beyond the MIL-PRF-39012 upper frequency limit of 18 GHz,
Wire and Cable Heat-shrink Tubing Non-shrink Tubing Braided Sleeving Screening Braids Moulded Parts Terminals and Splices Wire and Cable Markers
Wire and Cable Heat-shrink Tubing Non-shrink Tubing Braided Sleeving Screening Braids Moulded Parts Terminals and Splices Wire and Cable Markers Accessories Connectors Backshells Bonding Leads Metal Braids
Table of Contents. Version 5.0
Version 5.0 Table of Contents Vivid S 270 Static 2-11 Specifications Technical Specifications 3-5 Epistar 5 Nichia 5 Testing Certifications 6 Fixture Testing 6 Photometric Data 7 Charts 8-11 Vivid S 270
Z-002-IC-5L-F29BK
LazrSPEED Indoor/Outdoor Low Smoke Zero Halogen Riser Interconnect Cable Product Classification Portfolio Product Type Regional Availability CommScope Fiber indoor/outdoor cable Asia Australia/New Zealand