PTFE Elastomer Physical Properties
|
|
- Stewart Roberts
- 5 years ago
- Views:
Transcription
1 PTFE Property ASTM Method Value Specific Gravity D Tensile Strength D4894 4,360 psi Break D % Compressive Modulus 50, % 5% Strain 1,050 psi 1,660 psi Hardness D Shore D PTFE meets the following certifications: FDA, Class VI, 3A and ADI Free -100ºF to 500ºF (-73ºC to 260ºC) The preceeding data gives the typical properties of PTFE material. These are typical properties and should not
2 Tuf-Steel Property ASTM Method Value Base Material D4894 PTFE Filler 316 Stainless Steel Color Grey Specific Gravity D Tensile Strength D4894 1,780 psi Break D % Compressive Modulus 84, % 5% Strain 1,590 psi 2,620 psi Hardness D Shore D Tuf-Steel meets the following certifications: FDA, Class VI, 3A and ADI Free -320ºF to 550ºF (-195ºC to 288ºC) The preceeding data gives the typical properties of PTFE material. These are typical properties and should not
3 FKM Property Tensile Strength Value Min 1,500 psi Break Min 100 Durometer 85 Shore A (+/-5) Specific Gravity FKM meets the following certifications: FDA, Class VI, 3A and ADI Free -30ºF to 400ºF (-34ºC to 204ºC) The preceeding data gives the typical properties of FKM material. These are typical properties and should not
4 Platinum Silicone Property* Test Method Value Appearance WSTM 2298 Translucent Specific Gravity, 25ºC WSTM Extrusion Rate Catalyzed, 25ºC g/min** WSTM Pot Life, hrs, 25ºC*** WSTM ºF to 450ºF (-40ºC to 232ºC) Press Cured 5 min/166ºc Post Cured 4 hr/204ºc Hardness, Shore A WSTM Tensile Strength WSTM MPa 1,400 psi 9.66 MPa 1,400 psi Elongation, % WSTM Tear Strength, die B WSTM 1160 Compression Set, Method B (22 hr/177ºc) kn/m 190 psi kn/m 130 psi WSTM Shrink, % WSTM Brittle Point, ºC ASTM D746 N/A -73 Silicone meets the following certifications: FDA, Class VI, 3A and ADI Free *Properties obtained after mixing Part A and Part B in a ratio of 1:1. **Extrusion rate obtained at 90 psi and inch orifice. ***Pot life determined by time required for extrusion rate to be reduced to 50% of initial value. The preceeding data gives the typical properties of Silicone material. These are typical properties and should not
5 Buna Property ASTM Method Value Shore A Durometer, Points Tensile Strength Ultimate Elongation,,, 68 1,392 psi 527% Specific Gravity D Compression Set D Method B 84.8% Tear Resistance D lbf/in -30ºF to 200ºF (-34ºC to 93ºC) The preceeding data gives the typical properties of Buna material. These are typical properties and should not
6 EPDM Property Test Method Value Base Polymer EPDM Durometer Shore A Tensile Strength Ultimate Elongation 300% Modulus psi 605% 632 psi Tear Resistance D (32.9 kn/m) Compression Set D395-98, Method B 34.1% Brittle Point, ºC ASTM D746 N/A EPDM meets the following certifications: FDA, Class VI, 3A and ADI Free -30ºF to 300ºF (-34ºC to 149ºC) The preceeding data gives the typical properties of EPDM material. These are typical properties and should not
2 AA 720 A13 C12 EA14 F17 EA14 3 AA 720 B13 B33 C12 F17 EA14 4 AA 720 A13 B13 B33 C12 F17 EA14 5 AA 720 A13 B13 B33 C12 F17 EA14
Compound is a 70 durometer black colored high strength EPDM rubber formulated specifically for use in alkalis and acids, with the exception of concentrated sulfuric and nitric acid. It exhibits good resistance
More informationTechnical Information and Test Results for FenForm TM Silicone Sheet Composite Manufacturing
Technical Information and Test Results for FenForm TM Silicone Sheet Composite Manufacturing 1 Contents FenForm TM Typical Physical Properties 4 General Materials Properties 4 Recommended Curing Conditions
More informationMaterial Name Durometer Notes Food Contact Momentive SE Base 35 Used in blend of 6035 & 6075 to provide custom. Yes Momentive SE Base
Technical Reference Bulletin Elastomer Library C&M Rubber Co. has a longstanding business relationship with many polymer suppliers, including Momentive (Formerly GE Silicone), Wacker Silicone, US Silicones,
More informationPharm-A-Clear. Silicone. Bio-Compatible Ultra-Low Extractables Non-Pyrogenic Non-Hemolic. Silicone. High-Performance Platinum-Cured Tubing
High-Performance Platinum-Cured Tubing Bio-Compatible Ultra-Low Extractables Non-Pyrogenic Non-Hemolic TBL Plastics, LLC PO Box 634 Andover, New Jersey 07821 Tel. 973.383.2834 Fax 973.383.4161 sales@tblplastics.com
More informationSPECIFICATIONS: SAE J200/ASTM D2000 M3DA710A26B36C32EA14F19
TYPICAL PHYSICAL PROPERTIES - E34 (E17434) BLACK EPDM SPECIFICATIONS: SAE J200/ASTM D2000 M3DA710A26B36C32EA14F19 E34 (E17434) Shore A Durometer 70±5 68 Tensile, MPa, min. 10 17.5 Elongation, %, min. 200
More informationUNIPRENE. Shaping a New World of Opportunities THERMOPLASTIC ELASTOMER DIVISION
THERMOPLASTIC ELASTOMER DIVISION Unique TPVs providing the look and feel of rubber with the processing ease of TPOs. Ideal for pre-colored, soft-touch and engineered custom applications. Shaping a New
More informationBellofram Silicones Inc Ohio River Boulevard Newell, West Virginia Toll-free: Fax:
TM Silicones Bellofram Silicones Inc. 8019 Ohio River Boulevard Newell, West Virginia 26050 www.belloframsilicones.com Bellofram Closed Cell Silicone Sponge Extrusion Products Bellofram Silicones closed
More informationSIL CLASS VI SUPPORTED HIGH CONSISTENCY SILICONE ELASTOMER
LIFE SCIENCES PREMIUM CARE LINE SIL2-5030 CLASS VI SUPPORTED HIGH CONSISTENCY SILICONE ELASTOMER DESCRIPTION APPLICATION A two-part, high consistency elastomer designed for optimal performance in a wide
More informationRTV123. Technical Data Sheet RTV123
Technical Data Sheet RTV123 RTV123 Description RTV122, RTV123 and RTV128 adhesive sealants are one-component, ready-to-use, and cure to a tough, resilient silicone rubber on exposure to atmospheric moisture
More informationRTV128. Technical Data Sheet
Technical Data Sheet RTV128 Description RTV122, RTV123 and RTV128 adhesive sealants are one-component, ready-to-use, and cure to a tough, resilient silicone rubber on exposure to atmospheric moisture at
More informationCOMMERCIAL ITEM DESCRIPTION RUBBER, SILICONE
INCHPOUND AA59588A 7 July 2005 SUPERSEDING AA59588 12 January 2001 COMMERCIAL ITEM DESCRIPTION RUBBER, SILICONE The General Service Administration has authorized the use of this commercial item description
More informationXIAMETER Silicone Rubber
Plastics and Rubber Consumer Solutions XIAMETER Silicone Rubber Compounding Guide Foreword This simple compounding guide has been designed to help compounders and fabricators that are operating in the
More informationFluid Sealing Association
Fluid Sealing Association STANDARD FSA-PSJ-703-11 GUIDELINES FOR ELASTOMERS USED IN PIPING SYSTEMS NON-METALLIC EXPANSION JOINTS REVISED AUGUST 2011 (supersedes 1999 edition) 994 Old Eagle School Road,
More informationPushing the Boundaries of Fluorosilicone Rubber. Dr. R. A. Drake, Dr. L. M. Tonge, P. J. Griffith, Dr. K. B. King
Pushing the Boundaries of Fluorosilicone Rubber Dr. R. A. Drake, Dr. L. M. Tonge, P. J. Griffith, Dr. K. B. King Topics Overview of Fluorosilicone Rubber (FVMQ) Dow Corning Innovation in FVMQ High Resilience
More informationParker TexMed Heat Shrink. Quick Reference Guide. aerospace climate control electromechanical filtration
aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding Parker TexMed Heat Shrink Quick Reference Guide TexMed Adds Value Parker
More informationCOMMERCIAL ITEM DESCRIPTION RUBBER, SILICONE
INCH-POUND January 12, 2001 SUPERSEDING ZZ-R-765E/GEN May 10, 1989 COMMERCIAL ITEM DESCRIPTION RUBBER, SILICONE The General Service Administration has authorized the use of this commercial item description
More informationCOMMERCIAL ITEM DESCRIPTION RUBBER, SILICONE
INCH-POUND A-A-59588 January 12, 2001 SUPERSEDING ZZ-R-765E/GEN May 10, 1989 COMMERCIAL ITEM DESCRIPTION RUBBER, SILICONE The General Service Administration has authorized the use of this commercial item
More information3B CERTIFIED SILICONES WITH HIGH FLEX-FATIGUE RESISTANCE
JANUARY 2017 WHITE PAPER 3B CERTIFIED SILICONES WITH HIGH FLEX-FATIGUE RESISTANCE By: Modus TM Technical Team Modus Advanced, Inc. 2016 www.modusadvanced.com sales@modusadvanced.com (925) 248-9493 Silicones
More informationStep-By-Step Product Selection Guide
Step-By-Step Product Selection Guide Silicone Moldmaking Materials Europe and Asia Edition If you re looking for an easy-to-use moldmaking material that will deliver consistently superior results, look
More informationPERMANENCE English SI Metric. Specific Gravity D 792 Molding Shrinkage 1/8 in (3.2 mm) section in/in
Product Data Sheet & General Processing Conditions RTP 6042-50A Speciality Thermoplastic Elastomer Preliminary Datasheet PROPERTIES & AVERAGE VALUES OF INJECTION MOLDED SPECIMENS PERMANENCE English SI
More informationAMILON Custom PTFE Products
AMILON Custom PTFE Products Technetics PTFE & Polymer Solutions is the manufacturer of AMILON custom products, a family of PTFE based materials that are a smart alternative to RULON. AMILON specialty materials
More informationGeneral Processing Information
COMPOSITE DATA VIBRATHANE General Processing Information Urethane Prepolymers CROMPTON CORPORATION CHEMICAL offers the most versatile line of liquid urethane prepolymers and curatives in the market today.
More informationFluorosilicones in the Aerospace Industry Nathan Lipps, NuSil Technology
Introduction: Fluorosilicones in the Aerospace Industry Nathan Lipps, NuSil Technology Fluorosilicone s advent into the commercial marketplace offers opportunities for manufacturers to pursue new applications
More informationAmilon. The Alternative to Rulon
Amilon The Alternative to Rulon It all starts with the right material Because we control our own PTFE compounding, sintering, and machining, we are able to create PTFE shapes or components to your exact
More informationSA 450/65 Material Data Sheet
General Product Information SA 450/65 Material Data Sheet SA 450/65 is a speciality medical grade platinum cured elastomer, offering high clarity combined with excellent physical properties with a dry
More informationMillathane. Millathane
Millathane A HIGH PERFORMANCE MILLABLE POLYESTER URETHANE RUBBER TSE INDUSTRIES, INC. (Formerly known as Vibrathane ) TSE INDUSTRIES INC. CLEARWATER, FLORIDA For the past forty years, TSE Industries has
More informationTHERMAX versus Furnace Blacks
THERMAX versus Furnace Blacks With a particle size approximately ten times that of N33 furnace black, N99 has the smallest surface area of all the blacks commonly used in compounding rubber. These characteristics
More informationHigh Performance Pump Tubing. Superior Performance in Peristaltic-Pump Applications
TM Multiple Autoclave Cycles Lot and Batch Traceable Superior Pump Life Low Particulate USP Class V Superior Performance in Peristaltic-Pump Applications Our tubing was specifically developed to provide
More informationA. Submit to the Engineer as provided in Section shop drawings showing details of construction and erection for each tank as follows:
Specification for High Density Crosslinked Polyethylene Oxidation Resistant Lined Tank With Integrally Molded Flanged Outlet (IMFO) Specifically for Sodium Hypochlorite PART 1: GENERAL 1.01 SCOPE OF WORK
More informationFlowSmart High Purity Solutions
FlowSmart High Purity Solutions FlowSmart High Purity Solutions Polysource Clamp And Gasket Assembly Gauge Guard TM Isolator Polyscreen tm and Filtering Products Source Assemblies provide access to your
More informationTexin RxT65D. Characterization
Characterization Properties / Applications Medical Applications Texin RxT65D resin is an aromatic polyether-based thermoplastic polyurethane. It can be processed by injection molding, extrusion or blow
More informationA-601C. Technical Information. Fluoroelastomers
A-601C Technical Information Introduction Viton A-601C* fluoroelastomer is a new generation incorporated cure A-family dipolymer designed for compression molding of sealing devices that must meet major
More informationTexin RxT70A. Characterization
Characterization Properties / Applications Medical Applications Texin RxT70A resin is an aromatic polyether-based thermoplastic polyurethane. It can be processed by injection molding or extrusion. Texin
More informationOptimum diene content. Easy handling Shorter mixing cycle Efficient in short CV lines (Jet air / hot air)
Your Benefits Class A Sealing Superior surface aspect Meets major car makers specifications High physicals and elasticity with low polymer content Optimum filler dispersion Extrusion smoothness Cost Effectiveness
More informationAdvantages of Peroxide Dispersions in HCR Silicone Compounding
Advantages of Peroxide Dispersions in HCR Silicone Compounding By Erick Sharp (Speaker) ACE Products & Consulting LLC, Uniontown, OH Presented at the 2016 ACS International Elastomer Conference October
More informationSantoprene TPV Advanced Elastomer Systems - Thermoplastic Elastomer Tuesday, September 11, 2007
All values included in this document are for reference purposes only and should not be construed as material specifications. The test methods on this Product Data Sheet indicate the internationally recognized
More information3M Dynamar. Technical Information. Elastomer Additive FC Typical Properties (Data not for specification purposes) Introduction
Typical Properties (Data not for specification purposes) Specific Gravity [3M 14.10.C] 1.80 Color Creamy white, light tan Solubility Ketones and Esters Introduction Dynamar FC 2172 is a cure accelerator
More informationSilicoflex J O I N T S E A L I N G S Y S T E M. R.J. Watson, Inc. Bridge & Structural Engineered Systems
Silicoflex J O I N T S E A L I N G S Y S T E M R.J. Watson, Inc. Bridge & Structural Engineered Systems Silicoflex J O I N T S E A L I N G S Y S T E M Technology The Silicoflex Joint Sealing System is
More informationMaterials Library Advanced materials designed to deliver beautiful results. FORMLABS MATERIAL LIBRARY
Materials Library Advanced materials designed to deliver beautiful results. FORMLABS MATERIAL LIBRARY 1 Exceptional Print Quality The Form 2 delivers professional-quality printed parts at a fraction of
More informationMaterial EPDM EP703901
page 1/ Physical properties required actual Density ISO 2781 A Hardness ASTM D2240, Shore A, 23 Tensile strength ISO 37-2 Elongation at Break ISO 37-2 Tear strength ISO 34-1, B, 23 Tear strength ISO 34-1,
More informationDIVISION 3 - CONCRETE Section Control Joint Sealers
Spec Component: SC-072A-03/10 Sikadur 51 SL DIVISION 3 - CONCRETE Section 03930 - Control Joint Sealers Part 1 - General 1.01 Summary A. This specification describes the sealing of saw-cut, control, and
More informationDIVISION 7 - THERMAL AND MOISTURE PROTECTION Section Joint Sealers Elastomeric and non-elastomeric sealant
Spec Component: SC-070-03/10 Sikaflex- 15LM Part 1 - General DIVISION 7 - THERMAL AND MOISTURE PROTECTION Section 07900 Joint Sealers Elastomeric and non-elastomeric sealant 1.01 Summary A. This specification
More informationTECHNICAL BULLETIN. EPDM Engine Mounts
TECHNICAL BULLETIN EPDM Engine Mounts Abstract Increasingly hostile under-the-hood environments have led to an examination of EPDM as a replacement for natural rubber in automotive engine mounts. Thermal
More informationTECHNOLOGY FEATURES. Fast and Simple Installation. Low Stress Design. Maintenance Friendly. Large Movement Range. Temperature Insensitive.
TECHNOLOGY The Silicoflex Joint Sealing system was developed as a direct response to bridge owners asking for a higher quality, longer lasting, more universal joint sealing system. The Silicoflex system
More informationVibrathane A TDI-terminated polyester based prepolymer
199 Benson Road Middlebury, CT 06749 USA 203-573-2000 www.chemtura.com Effective: 09.04.2007 Vibrathane 8070 A TDI-terminated polyester based prepolymer VIBRATHANE 8070 is a TDI-terminated polyester based
More informationConductive Elastomers
Elastomer is an exceptional versatile EMI shield material providing extremely low contact resistance between mating surfaces. By loading highly conductive metal fillers into silicone or fuel resistant
More informationSILASTIC RTV-3110 Mould-Making Base SILASTIC RTV-3112 Mould-Making Base SILASTIC RTV-3120 Mould-Making Base
Technical Data Sheet 3110 Mould-Making Base 3112 Mould-Making Base 3120 Mould-Making Base General purpose silicone moldmaking rubbers. Features & Benefits Two-part RTV silicone rubbers Low mixed viscosity
More informationMaterials Data Sheet. Photopolymer Resin for Form 1+ and Form 2
Materials Data Sheet Photopolymer Resin for Form 1+ and Form 2 Prepared 09. 18. 2018 Rev 06 01. 22. 2019 STANDARD RESINS CLEAR FLGPCL04 WHITE FLGPWH04 GREY FLGPGR04 BLACK FLGPBK04 COLOR BASE FLGPCB01 Ultimate
More informationCaltrans G Bonded Joint Seals
Caltrans 51-2.02G Bonded Joint Seals Wabo SPS Joint System Preformed Silicone Seal Joint Sealing System DESCRIPTION: The Wabo SPS Joint System is approved for use under Caltrans Section 51-2.02G Bonded
More informationA-331C. Technical Information. Fluoroelastomers
A-331C Technical Information Introduction Viton A-331C* is an incorporated cure A-family dipolymer designed for the injection and transfer of molding parts requiring improved demolding hot tear resistance.
More informationEvaluation of DISPERSIX in HCR Silicone Compounding
Evaluation of DISPERSIX in HCR Silicone Compounding By Erick Sharp (Speaker) ACE Products & Consulting LLC, Uniontown, OH Miles Dearth The SEFA Group, Lexington, SC Bill Black The SEFA Group, Lexington,
More informationSpecification for Crosslinked Polyethylene Double-Wall Storage Tank with Enclosed Secondary Containment
Specification for Crosslinked Polyethylene Double-Wall Storage Tank with Enclosed Secondary Containment Note: Do not use this spec. for sodium hypochlorite, sulfuric acid or hydrochloric acid These chemicals
More informationReport of Product Testing ASTM C603/C920/D412/D792 Product: Chemcon Self-Leveling Sealant TEC PRO TEC Laboratory No:
September 29, 2017 Chemical Construction Company Miguel Idalgo 753, Cerro Azul, Veracruz, 92511, Mexico Subject: Report of Product Testing C603/C920/D412/D792 Product: Chemcon Self-Leveling Sealant TEC
More informationPRODUCT FORM APPLICATIONS THERMAL PROPERTIES CHEMICAL COMPOSITION GENERAL INFORMATION
ISSUE NO: 4 ISS DATE: 2013 APPROVED: NJRS Certificate No. 03 TECHNICAL DATA SHEET SILICONE RUBBER SPONGE GRADES: SIL10, SIL16, SIL, SIL33 PRODUCT FORM Profile extrusions, sheeting, cord, joined rings,
More informationA typical joint sample is 140mm long and is held in specially designed clamps.
Vulc-O-rings One of our oldest and most popular products is the Hot Vulcanised Cord ring ( Vulc-O-ring ). Eriks has developed a very successful method of producing O-rings from extruded cord to a very
More informationIntroducing. DuPont TM ETPV engineering thermoplastic vulcanizates. Resists Oil and Heat
Introducing engineering thermoplastic vulcanizates Katherine Cook Orvar Otterstedt October 1 29, 2003 DuPont ETPV Description Overall Performance ETPV Positioning Potential Applications Grades for Customers
More informationDOWSIL 123 Silicone Seal
Technical Data Sheet Preformed silicone seal for weatherproofing applications Features & Benefits Economical, high-performance alternative to cutting-out and recaulking existing failed weatherproofing
More informationSpecialty Expansion Joint Systems
www.dsbrown.com Specialty Expansion Joint Systems Bridges Expansion Joint Systems for Architectural, Parking Garage and Bridge Applications Bridge the World with Leading Infrastructure Solutions Corporate
More informationHigh Performance Silica Tread. with. Next Generation. Struktol Process Additives
Producers of Specialty Chemicals Struktol Company of America 1 E. Steels Corners Road P. O. Box 1649 Stow, Ohio 444-649 www.struktol.com High Performance Silica Tread with Next Generation Struktol Process
More informationInformation Technology Solutions
Adiabatics, Inc. has been involved in research and development projects focused on wearresistant coatings for a wide range of companies and applications. Most have utilized traditional thermal/flame sprayed
More informationSA 450/60 Material Data Sheet
General Product Information SA 450/60 Material Data Sheet SA 450/60 is a speciality medical grade platinum cured elastomer, offering high clarity combined with excellent physical properties. It is none
More informationEpoxy Systems MOUNTING. See pages I-IV for ordering information or visit Resin Part Number Size
Epoxy Systems Material Description Resin Hardener EpoxiCure 2 Clear, general purpose epoxy system 6hr cure time at room Mix Ratio: 4 parts resin : 1 part hardener by volume
More informationISMAT SPECIFICATIONS
ISM-FKM-7512 Technical Datasheet ISM-FKM-7512 base polymer is an Engineering purpose Fluorocarbon compound. FKM O Rings can be used in petroleum products and solvent resistant applications such as Valve
More informationRUBBER MATERIAL COMMERCIAL and MIL SPEC
RUBBER MATERIAL COMMERCIAL and MIL SPEC NEOPRENE BUNA-N FDA BUNA-N VITON EPDM SILICONE CLOTH INSERTED RUBBER NYLON INSERTED RUBBER RED RUBBER PURE GUM CLOSED CELL SPONGE OPEN CELL SPONGE CORK and RUBBER
More informationRubber Material Selection Guide Nbr Nitrile Or Buna N
We have made it easy for you to find a PDF Ebooks without any digging. And by having access to our ebooks online or by storing it on your computer, you have convenient answers with rubber material selection
More information353 Circuit Street Hanover, Massachusetts Toll Free # 877 SAY HAPCO ( ) Fax#
2 TECHNICAL BULLETIN STERalloy FDG - FOOD & DRUG GRADE LIQUID MOLDING POLYMER ALLOYS - STERalloy FDG is the first Liquid Molding Polymer Alloy Series that has been specifically designed for food and drug
More informationRTV8112. Technical Data Sheet
Technical Data Sheet RTV8112 Description RTV8111, RTV8112 and RTV8262 silicone rubber compounds are two-part silicone elastomers supplied in ready-to-use matched kits containing a base compound and curing
More informationDaikinDAI-EL HighPerformanceFluoroelastomers
DaikinDAI-EL HighPerformanceFluoroelastomers DAI-EL Equals Quality Plus Performance Fluoroelastomer Expertise Daikin offers the most complete line of fluoroelastomer products in the world today. From low
More informationThermal Management Solutions for Automotive, Lighting and Industrial Applications
Thermal Management Solutions for Automotive, Lighting and Industrial Applications UL Prospector Webinar, January 25, 2018 Presented by Florian Damrath & Julien Renaud Technical Service & Development, Advanced
More informationTech Tip 15 Physical Properties
Tech Tip 15 Physical Properties Physical Properties of Printing Plate Materials Careful evaluation of the physical properties of plate materials can help you identify the rubber or photopolymer plate material(s)
More informationHygienic Sanitary Gasket
Hygienic Sanitary Gasket Compression Controlled Gaskets with Full Traceability of Materials 2 Hygienic Sanitary Gasket Superior Performance for High Purity Processing Parker s hygienic sanitary gaskets
More informationCORROSION-RESISTANT SILICONE GASKETS
CORROSION-RESISTANT SILICONE GASKETS 2 www.getelec.com 43 CORROSION-RESISTANT SILICONE GASKETS Guide to corrosion-resistant conductive materials by industry sector GETELEC has been developing its own MIL
More informationSTRUCTURE OF LED ENCAPSULATION SILICONES
STRUCTURE OF LED ENCPSULTION SILICONES Structure of LED Chip 400 886 872 LED lens (Silicone) 579 868 S 871 872 579 KLM 06005 (BLU) KLM 06006 (Light) Encapsulate material (Silicone) Gold wire Lead frame
More informationExcellent elasticity and recovery (memory) Heat or ultrasonically weldable
Experts in thin gauge specialty elastics Product Data Sheet TPE Tape A highly elastic, durable, weldable tape. Engineered for a comfortable fit. Available in a range of colors and dimensions. Features
More informationDow Corning XTI-1003 RTV Silicone Rubber Insulation
Dow Corning XTI-1003 RTV Silicone Rubber Insulation Advanced Technology for Subsea Wet Insulation Systems 1 Deepwater Flow Assurance More reliable, cost-efficient and lower-risk subsea wet insulation systems
More informationXIAMETER RTV-4250-S Kit Green
XIAMETER RTV-4250-S Kit Green High strength silicone moldmaking rubber FEATURES Outstanding release properties If required the product cure can be heat accelerated Fast thick section cure at room temperature
More information& CHO-SIL Conductive Elastomers
CONDUCTIVE ELASTOMERS CHO-SEAL & CHO-SIL Conductive Elastomers Since 1961, Chomerics has invented and extended virtually every aspect of conductive elastomer materials technology from the earliest silver
More informationSPECIFICATION SHEET. DK1410 Expanded Neoprene Sponge Rubber. Desc. Standard Value Unit 2C1 B3 M
DK1410 Expanded Neoprene Sponge Rubber 2C1 B3 M Density ASTM D3575 115-155 Kg/m³ Compression Deflection (25%) ASTM 1056 20-40 kpa Compression Deflection (50%) ASTM 1056 50-70 kpa Compression Set (25%/22h/23
More informationA-361C. Technical Information. Fluoroelastomers
Technical Information Introduction * is an incorporated cure A-family dipolymer designed for the injection and transfer molding of parts requiring better metal adhesion along with the fluid and heat resistance
More informationHigh strength silicone moldmaking rubber
Technical Data Sheet High strength silicone moldmaking rubber Features & Benefits Outstanding release properties If required the product cure can be heat accelerated Fast thick section cure at room temperature
More informationRTV577. Technical Data Sheet
Technical Data Sheet RTV577 Description RTV511, RTV560 and RTV577 silicone rubber compounds are low temperature two-part silicone elastomers. They are supplied ready to use with a base compound and DBT
More informationDETAIL SPECIFICATION SHEET. CLAMP, LOOP, TUBE-17-7 PH CRES, 500 o F
INCH-POUND MIL-DTL-85052/3C 30 March 2005 SUPERSEDING MIL-C-85052/3B 30 MAY 1984 DETAIL SPECIFICATION SHEET CLAMP, LOOP, TUBE-17-7 PH CRES, 500 o F This specification is approved for use by all Departments
More informationSection Gabions Tender No. [ ] Page The following detail drawings are appended hereto and form part of this section.
Tender No. [ ] Page 1 1.0 GENERAL 1.1 DETAILED DRAWINGS.1 The following detail drawings are appended hereto and form part of this section. Number Title 02374.01 Gabion Basket Assembly Details 02374.02
More informationBELLOFRAM SILICONES INC OHIO RIVER BOULEVARD NEWELL, WEST VIRGINIA TOLL-FREE: FAX:
TM Silicones BELLOFRAM SILICONES INC. 8019 OHIO RIVER BOULEVARD NEWELL, WEST VIRGINIA 26050 TOLL-FREE: +1.800.727.5646 FAX: +1.304.387.1212 www.belloframsilicones.com BELLOFRAM Closed Cell Silicone Sponge
More informationPUMP SEAL PARTS GUIDE
PUMP PARTS GUIDE TABLE OF CONTENTS How to Select Your Seals U1/ZP1 Single/Double O-Ring Seal Diagrams 3 U1/ZP1 Single/Double Mechanical Seal Diagrams 4 U1/ZP1 O-Ring Seal Kits 5 U1/ZP1 Mechanical Seal
More informationDMS EPOXIES AND ADHESIVES
DMS - 6100 EFFECTIVE DATES: OCTOBER 2007 MAY 2014. 6100.1. Description. This Specification details requirements for various types of epoxy and adhesive materials suitable for highway use. These materials
More informationTECHNICAL SPECIFICATION Conductive Elastomer Molded Gaskets
Pag. 1/6 TECHNICAL SPECIFICATION Conductive Elastomer Molded Gaskets This category of items is in continuous evolution. The raw material from which it is made is the first component that must be analyzed
More informationRaychem Fluoroelastomer Tubing Flexible, Fluid Resistant, Heat-Shrinkable
Tyco Electronics Corporation 300 Constitution Drive Menlo Park, CA 94025 USA Specification This Issue: Date: Replaces: RW-3037 Issue 2 July 26, 2006 Issue 1 Raychem Fluoroelastomer Tubing Flexible, Fluid
More informationA-200. Technical Information. Fluoroelastomers
A-200 Technical Information Introduction Viton A-200* fluoroelastomer is an A-family gum polymer that demonstrates improved processing when compared with existing fluoroelastomers.viton A-200 is designed
More informationAL 29-4C AL 29-4C. Technical Data Sheet. Stainless Steel: Superferritic INTRODUCTION (UNS S44735)
AL 29-4C Stainless Steel: Superferritic (UNS S44735) INTRODUCTION AL 29-4C alloy, is a superferritic stainless steel developed by ATI in the early 1980s specifically for power plant surface condenser tubing.
More informationRenCast 6444 / Ren 6444
Advanced Materials RenCast 6444 / Ren 6444 REN POLYURETHANES SEMI-RIGID, SHORE 60 ± 5 D POLYUREA ELASTOMER DESCRIPTION : RenCast 6444 (Resin) and Ren 6444 (Hardener) system is an extremely effective semi-rigid,
More informationViton A-331C. Technical Information
Technical Information Rev. 2, Feb. 2003 Viton A-331C Introduction Viton A-331C* is an incorporated cure A-family dipolymer designed for the injection and transfer molding of parts requiring improved demolding
More information8331S Technical Data Sheet Silver Conductive Epoxy Adhesive Good Conductivity / Slow Cure
Description This is a two-part, smooth, silver paste adhesive that cures to form a hard, durable polymer. In its cured state, it is highly electrically and thermally conductive. It adheres strongly to
More informationAchieving better processing of silica filled compounds
Achieving better processing of silica filled compounds Schill + Seilacher Struktol GmbH Hamburg, Germany Sebastian Fritsch, Colin Clarke, Manfred Hensel, Dr Herbert Schulze SGF Conference 23 th - 24 th
More informationNeuthane 100 Series TDI PTMEG Ether Prepolymers
TDI PTMEG Ether Prepolymers Quick Guide to Hardness Range: The following data is, unless otherwise stated, based on the hardness obtained when cured with MOCA. Other amine curatives are available and the
More informationBLUESIL V-340. Addition Cure Silicone Elastomer. Moldmaking February Description. Applications. Typical Properties
Moldmaking February 2012 BLUESIL V-340 Description Applications Typical Properties Addition Cure Silicone Elastomer BLUESIL V-340 is a two component, addition reaction, room temperature or heat accelerated
More informationRubber Material Selection Guide Nbr Nitrile Or Buna N
We have made it easy for you to find a PDF Ebooks without any digging. And by having access to our ebooks online or by storing it on your computer, you have convenient answers with rubber material selection
More informationSTERalloy FDG - FOOD & DRUG GRADE LIQUID MOLDING POLYMER ALLOYS -
TECHNICAL BULLETIN STERalloy FDG - FOOD & DRUG GRADE LIQUID MOLDING POLYMER ALLOYS - STERalloy FDG is the first Liquid Molding Polymer Alloy Series that has been specifically designed for food and drug
More informationEastman TXIB formulation additive. for vinyl plastisols
Eastman formulation additive for vinyl plastisols Eastman formulation additive Eastman formulation additive is a superior low-viscosity additive for PVC with plasticizing abilities. It has good compatibility
More information