Stop and Read Before Installing Material
|
|
- Cynthia Jocelyn Wood
- 6 years ago
- Views:
Transcription
1 Premium Dry Erase Materials Installation procedures for full wall application with woven and nonwoven backed products Stop and Read Before Installing Material Installation Procedures EXAMINATION Jot.a.wall materials should be carefully inspected to confirm the correct pattern and quantity ordered has been shipped. If any flaws appear, stop hanging and contact your regional distributor as soon as possible. SURFACE PREPARATION Proper surface preparation is critical for a quality dry erase material installation. Any imperfections in the wall will read through to the surface of the installed material. Surface must be clean, smooth, dry, structurally sound, and uniform in color. Any existing imperfections in the wall surface, such as cracks, taped joints, dents or screw heads should be sealed and sanded smooth. Ballpoint ink, grease, crayon, or any other foreign matter should be cleaned or removed. A LEVEL 4 or 5 wall finish must be achieved before installation begins. The entire wall surface must be consistent in color throughout, as any marks or color variations may possibly read through to the surface of the dry erase material. A white pigmented, high quality commercial acrylic primer is recommended to properly seal the wall and provide a consistent color base for the dry erase product. Wall surfaces should not exceed 5% moisture content as measured by a moisture meter. Apply product when the relative humidity in the installation area does not exceed 40% and the temperature is above 55 degrees F. These conditions
2 should be maintained in areas of both storage and installation for three days prior to and after the installation. If there are any questions concerning the surface to be covered, a test installation of at least one strip applied three days in advance of the main installation is recommended. Use only a lead pencil for marking the material on the reverse side of the dry erase surface. DO NOT use ball point pens, solvent based inks, or oil based markers. APPLICATION For full wall applications, it is recommended a full width strip be placed on the wall horizontally, to provide a writing space in the optimum seamless area of the material. The first strip should be cut 34 wide above the floor finish so when you doublecut the seam, it is 32 above the finished floor. #1 stripe should be 34 above floor finish. The second strip: Reverse strip #2 and place the 60 piece horizontally overlapping strip #1 approximately 4. This will allow for double cutting the seam to occur at the center of the 4 overlap, resulting in a finished seam approximately 32 off the floor.
3 Second strip 60 overlapping the first strip 4. Remember to reverse this strip. First stripe is 34 above floor finish. After double cutting the seam, it will be 32 above floor finish. After hanging the second strip, examine the installed material for color uniformity and overall appearance. Any problem with the installation should be communicated to the regional distributor before proceeding. Third strip: For the third strip use the remaining material from the first strip and hang it at the ceiling, reversing it accordingly. A level line must be established for an acceptable installation. Always seam the product using factory edge to factory edge. Never match a seam using the cut edge of the split sheet with the factory edge. Shading could result.
4 Third strip use the remaining material from the first strip. Reverse the material, overlapping the second strip 4. Double cut the material in the center of the 4. Second strip 60 overlapping the first strip 4. Remember to reverse this strip. First stripe is 34 above floor finish. After double cutting the seam, it will be 32 above floor finish. Use a high quality, heavy duty, clay-based strippable adhesive. Apply adhesive to the wall where the dry erase material will be hung. Be sure to cover the surface completely, making sure the edges and corners are coated as well. If installation is slow or halted you may need to recoat. Do not crease the material when handling. Keep the writing surface side free of any dirt or abrasives that may damage or scratch it during installation. Use a plastic (non-metal) smoothing tool wrapped with a clean, wet, auto chamois to ensure protection of the writing surface. The writing surface can be damaged by tools with hard, sharp, or abrasive edges. If the surface is scratched, marker residue may accumulate in the indentation and leave a permanent mark. Remove air pockets or paste lumps, working toward the uncovered wall. Work the material from the middle to the outside edge. Take care not to overwork the surface to avoid paste lumping. Overlapping and double cutting is recommended for best seaming results. Use the proper cutting tool so that you do not score the wall. Carefully roll or press the seams down, being careful not
5 to overwork the seams. It is critical that any foreign particles on the back of the material or the wall be removed before final installation. Change blades frequently to insure clean cuts. After hanging one horizontal strip of dry erase material, examine the installed material for color uniformity and overall appearance. Any problem with the installation should be communicated to the regional distributor before proceeding. CLEAN UP Be sure to remove all excess adhesive immediately using a clean soft sponge and clean water. Do not use abrasive cleaners or dirty water. Dry with a clean, soft towel. BEFORE USING ANY JOT.A.WALL MATERIAL, THE ENTIRE WRITING AREA MUST BE CLEANED TO INSURE PROPER PERFORMANCE. USE CLEAN WATER AND TOWEL DRY. REFER TO DETAILED JOT.A.WALL CARE AND MAINTENANCE INSTRUCTIONS.
EDIT ITEMS NOT INCLUDED IN THIS PROJECT
PART 1: GENERAL Premium Dry Erase Materials EDIT ITEMS NOT INCLUDED IN THIS PROJECT 1.01 SUMMARY A. Division Includes: 1. Dry Erase Wall Covering 2. Magnetic Self Stick Dry Erase Wall Coverings 3. Self
More informationInstallation Instructions
Installation Instructions Installing Real Wood Veneers Wood Veneer Wallcovering Please read these instructions prior to installation. If you have any questions regarding the installation procedures contained
More informationINSTALLATION INSTRUCTIONS July 2018
INSTALLATION INSTRUCTIONS July 2018 This Advanced Wall Protection (AWP) product installs with techniques similar to traditional type II vinyl wallcovering, but is a proprietary construction with key performance
More informationSECTION PRESENTATION DRY ERASE WALLCOVERING
SECTION 09720 PRESENTATION DRY ERASE WALLCOVERING Part 1 General 1.01 Summary EDIT ITEMS NOT INCLUDED IN THE PROJECT A. Section Includes: 1. Dry Erase Wallcovering 2. Low Glare Projection Dry Erase Wallcovering
More informationImportant. Installation Instructions. Ricochet Flexible Wall Protection. Ricochet must be installed by experienced Vinyl Wallcovering (VWC) installers
Important installs with techniques similar to traditional type II vinyl wallcovering, but is a proprietary construction with key performance advantages. Ricochet is packaged in 15-yard coreless rolls,
More informationSECTION POLYPROPYLENE FABRIC WALL COVERING
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 09 72 31 POLYPROPYLENE FABRIC WALL COVERING SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. Also delete any other item or paragraph not
More informationYARRABEE 360 GEOLOGY
Thank you for choosing our fine hand crafted GEOLOGY slate panels. For the best results, we believe that a contractor or professional wall covering installer with the correct tools should hang this material.
More informationMulti-Piece EasyStep Product Installation Instructions
Tools/materials you might need for proper installation 6D galvanized screws 100% silicone caulking (See specific caulking recommendations) caulking gun shims tape measure 1/8 drill bit Phillips screw driver
More informationTechnical Service. INSTALLATION INSTRUCTIONS FOR TARAFLEX SPORT PRODUCTS over Gypsum base Products. This document refers to the following products:
INSTALLATION INSTRUCTIONS FOR TARAFLEX SPORT PRODUCTS over Gypsum base Products This document refers to the following products: Product Width Width Ft. Installation direction Seams treatment Taraflex Surface
More informationMulti-Piece EasyStep Product Installation Instructions
Tools/materials you might need for proper installation 6D galvanized screws caulking gun shims tape measure 1/8 drill bit Phillips screw driver cardboard china marker (or grease pencil) furring strips
More informationSECTION DRY ERASE COATING (IdeaPaint CREATE Black and White) A. Section Gypsum Board Assemblies; gypsum board substrate.
Guide Specifications for Designers and Specifiers: This document specifies IdeaPaint CREATE Dry Erase Coating by IdeaPaint, and is provided for your use in CSI 3-Part Format. For further assistance, call
More informationInstallation Instructions. Important. Recommended Tools. Palladium Rigid Sheet/Rubrail or Palladium G2 Sheet/Rubrail. Storage
Important Storage Flat sheet - Store Palladium Rigid Sheet in a clean, dry, interior area at temperatures between 50 F and 95 F [10-35 C]. Keep out of direct sunlight. Make sure sheet is well supported.
More information6032 SH 3P Residential Shower Installation Instructions Gelcoat & Solid Surface Bathware
Tools/materials you might need for proper installation 6D galvanized screws 100% silicone caulking caulking gun acrylic latex caulk shims tape measure 1/8 drill bit Phillips screw driver cardboard china
More informationFreedom One-Piece Barrier Free Showers Installation Instructions
Tools & Materials you might need for proper installation Materials: 2-1 gallon buckets of solid wood flooring adhesive or 100% silicone adhesive (non-shrink) 20-1.25 wood screws 1-5 gallon bucket (to mix
More informationFor wooden fabricated underlay e.g. plywood, care must be taken to store the material in an area where it will not become damp or contaminated.
Page 1 1.30MM VERTICAL AND T The preparation/dryness of the wall / subfloor and installation procedures should all be as BS 476. i.e.: The relative humidity of the wall must be below 75%RH when tested
More informationAcoustic Fabrics, an Aesthetic Addition to Controlling Commercial Noise
Acoustic Fabrics, an Aesthetic Addition to Controlling Commercial Noise Acoustic fabrics are simply versatile, easy to retrofit, cost-effective with outstanding noise absorption qualities Our acoustic
More informationARTISAN INSTALLATION INSTRUCTIONS ROLLS
Bolon 2016-02-01 1 (3) INSTALLATION INSTRUCTIONS ROLLS THE MATERIAL The material is a woven vinyl product backed with glassfibre-reinforced vinyl. Since the material is a woven product, its structure is
More informationGRAPHIC INSTALLATION INSTRUCTIONS ROLLS - BOLON GREEN WELD
1 (5) INSTALLATION INSTRUCTIONS ROLLS - BOLON GREEN WELD THE MATERIAL The material is a woven vinyl product backed with glass fiber reinforced vinyl. Since the material is a woven product, its structure
More informationBKB INSTALLATION INSTRUCTIONS ROLLS - BOLON GREEN WELD
1 (4) INSTALLATION INSTRUCTIONS ROLLS - BOLON GREEN WELD THE MATERIAL The material is a woven vinyl product backed with glass fiber reinforced vinyl. Since the material is a woven product, its structure
More informationBOLON BY MISSONI INSTALLATION INSTRUCTIONS ROLLS - BOLON GREEN WELD
1 (4) INSTALLATION INSTRUCTIONS ROLLS - BOLON GREEN WELD THE MATERIAL The material is a woven vinyl product backed with glass fiber reinforced vinyl. Since the material is a woven product, its structure
More informationEngineering Branch Assets Delivery Group
F.1 SCOPE This Technical Specification shall apply to Fibre Reinforced Plastics or Glass Reinforced Plastics (hereinafter referred to as FRP or GRP) structures and the materials used in their manufacture,
More informationARTISAN INSTALLATION INSTRUCTIONS ROLLS - BOLON GREEN WELD
1 (4) INSTALLATION INSTRUCTIONS ROLLS - BOLON GREEN WELD THE MATERIAL The material is a woven vinyl product backed with glass fiber reinforced vinyl. Since the material is a woven product, its structure
More informationMTI BATHS BOUTIQUE COLLECTION ENGINEERED SOLID STONE SHOWER BASES OWNER S MANUAL INSTALLATION GUIDE EFFECTIVE JANUARY 1, 2013
MTI BATHS BOUTIQUE COLLECTION ENGINEERED SOLID STONE SHOWER BASES OWNER S MANUAL INSTALLATION GUIDE EFFECTIVE JANUARY 1, 2013 Installer: this booklet must be given to the product owner. Please note important
More informationL. W. Mountain, Inc. Floating Glue Installation Instructions *For use with engineered floors only*
L. W. Mountain, Inc. Floating Glue Installation Instructions *For use with engineered floors only* Inspect the job site carefully before you begin the installation. Some conditions require specific installation
More informationLUXURY VINYL PLANK & TILE MAINTENANCE GUIDE
MILLIKEN LVT MAINTENANCE GUIDE FOR GLUE DOWN AND FREE LAY PRODUCTS Date: 08/2017 LUXURY VINYL PLANK & TILE MAINTENANCE GUIDE All instructions and recommendations in this guide are based on the most recent
More informationFreedom Barrier Free Shower Pan Installation Instructions
Tools & Materials you might need for proper installation Materials: 2-1 gallon buckets of solid wood flooring adhesive (non-shrink) or 100% silicone adhesive 20-1.25 wood screws 1 - tube of non-shrink
More informationFreedom Barrier Free Shower Pan Installation Instructions
Tools & Materials you might need for proper installation Materials: 2-1 gallon buckets of solid wood flooring adhesive (non-shrink) or 100% silicone adhesive 20-1.25 wood screws 1 - tube of non-shrink
More informationInstallation and Maintenance instructions
PVC Floorcovering Resilient Residential Installation and Maintenance instructions February 2014 IMPORTANT! Make sure all specifications and instructions are followed carefully. Floor covering exclusively
More informationNeed help? Give us a call.
Need help? Give us a call. Call our support line at 1.800.765.6699 if you are unclear on any step of the application. You ll be helped by an experienced professional painter, just like you. WEB: www.zolatone.com
More informationMirroFlex Tub and Shower Walls Kit Installation Instructions
MirroFlex Tub and Shower Walls Kit Installation Instructions MirroFlex Tub and Shower Walls must be acclimatized for 24 hours before installation! PLEASE READ ALL INSTRUCTIONS PRIOR TO INSTALLATION: The
More informationProduct Guide Specification
Product Guide Specification Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat,
More informationPittsburgh Corning Glass Block Shower System Mortar Installation Standard Fit Shower Instructions
1. Shower Base and Wall Preparation 1.1 After installation of the shower base, line base with paper or cardboard to protect during installation of the glass blocks. Measure 2 ½ inches out from the inside
More informationSECTION VINYL-COATED FABRIC WALL COVERINGS
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 09 72 16 VINYL-COATED FABRIC WALL COVERINGS SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationStructural/ Manufacturing Warranty for products purchased after January 1 st, 2010.
Logs End Warranty Structural/ Manufacturing Warranty for products purchased after January 1 st, 2010. Logs End warrants its products, in their original manufactured condition, to be free from defects in
More information1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards.
WOOD FLOORING GENERAL INFORMATION 1.1 This section applies to factory finished wood strip flooring. 1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards. 1.3
More informationINSTALLATION INSTRUCTIONS FOR WICANDERS DEKWALL
INSTALLATION INSTRUCTIONS FOR WICANDERS DEKWALL GENERAL INFORMATION Wicanders Dekwall coverings are intended for indoor use only. Please, read the following instructions before installation. Store tiles
More informationInstallation Instructions
Installation Instructions 160 South Industrial Blvd. Technical Services Department Calhoun, Georgia 30701 508 East Morris St. Dalton, Georgia 30721 www.mohawkgroup.com 800.833.6954 2 Carpet Installation
More informationInsta-DE 2a Series Section 1: Screen Design.
Insta-DE 2a Series Section 1: Screen Design. 1.1 What is it? Convert entire walls into a dry-erase whiteboard projection screen: The Insta-DE2a is a self-adhesive wall covering film material that instantly
More informationThe use of wood putty, wood filler and wood stain for enhancement of the flooring should be accepted as normal.
3/4 SOLID HARDWOOD STRIP AND PLANK FLOORING INSTALLATION INSTRUCTIONS FOR MECHANICALLY FASTENED, STAPLE, NAIL OR CLEAT APPLICATIONS I. GENERAL INFORMATION Owner/Installer Responsibility: Beautiful hardwood
More informationDATA SHEET DEKSTER 131 SELFLEVELLING FLOOR COAT / UNDERLAY
(Page 1 of 8 ) GENERAL DESCRIPTION - Dekster 131 self levelling is a contemporary coating that achieves hard wearing, utilitarian floor surfaces in a range of natural tones to offset any style of interior.
More informationImpression Graphic panels
Impression Graphic panels Installation Guidelines 6003.I Rev. 02 8/15 Please Read Disclaimers: PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION!! These guidelines are provided in good faith to
More informationBOLON BY YOU INSTALLATION INSTRUCTIONS ROLLS
1 (5) THE MATERIAL The material is a woven vinyl product backed with glassfibre-reinforced vinyl. Since the material is a woven product, its structure is naturally irregular. The material is not approved
More informationFlexLok Adhesive Tabs for Carpet Tile
FlexLok Adhesive Tabs for Carpet Tile INSTALLATION EcoFlex ICT EcoFlex NXT 160 South Industrial Blvd. Calhoun, GA. 30701 MohawkGroup.com Technical Services Department 508 East Morris St. Dalton, GA 30721
More informationCREATE INSTALLATION INSTRUCTIONS ROLLS - BOLON GREEN WELD
1 (4) INSTALLATION INSTRUCTIONS ROLLS - BOLON GREEN WELD THE MATERIAL The material is a woven vinyl product backed with glass fiber reinforced vinyl. Since the material is a woven product, its structure
More informationPoly and Anti Graffiti Films Clear exterior films safeguarding plastic substrates from scratches, discoloration and graffiti.
TECHNICAL BULLETIN Avery Dennison Poly Films issued: 01/2018 Introduction Avery Dennison Poly and Universal Anti Graffiti Films are a range of clear and metallized exterior installation films specifically
More informationLaminate Flooring Charlestowne Collection
Laminate Flooring Charlestowne Collection Warranty This quality laminate flooring is under warranty for 25 years not to fade, wear through or stain. This warranty applies only to the original purchaser.
More informationA. Section Mirrors; mirrors for architectural application to receive window film.
1.1 SECTION INCLUDES A. Anti-graffiti window films for glazing systems and mirrors. 1.2 RELATED SECTIONS A. Section 08300 Mirrors; mirrors for architectural application to receive window film. B. Section
More informationwritelite & writeprolite (self adhesive film)
product description This document references the manufacturer s WriteLite Whiteboard films as the Product. This product is a unique architectural finish with a writable and erasable surface that can be
More informationInstallation Guide. Please verify seaming layout against scope of work to ensure all areas have been covered.
Installation Guide Thank you for choosing a quality carpet from Dansk Wilton. With the correct installation, normal use and correct maintenance you can look forward to a positive carpet experience for
More informationInstallation Instructions for Hercules Rib 52
Page 1 of 5 Installation Instructions These instructions supersede any verbal or written instructions from connexus representatives, and must be followed in order for the warranty to be in effect. Delivery
More informationPry Bar or Pull bar Hammer Spacing Wedges Rubber Mallet Safety Equipment (Goggles and Mask)
strand at ease installation instructions strand at ease installation instructions: ECOFINISHES RECOMMENDS USING THE SERVICES OF A PROFESSIONAL HARDWOOD FLOORING INSTALLER. READ THESE INSTRUCTIONS THOROUGHLY
More informationSECTION RESILIENT SHEET FLOORING
SECTION 09665 RESILIENT SHEET FLOORING PART 1 - GENERAL 1.1 DESCRIPTION A. This Section specifies the installation of sheet flooring with backing and integral cove base. 1.2 RELATED WORK A. Color and pattern:
More informationMirroFlex Structures Ceiling Tiles Fabrication and Installation Instructions
MirroFlex Structures Ceiling Tiles Fabrication and Installation Instructions MirroFlex Structures are deeply textured ceiling tiles. MirroFlex Ceiling Tiles are opaque, thermoplastic square and rectangular
More informationConstruction. Pulastic Coating-221 W. 2 Component Polyurethane
Product Data Sheet: Version: 08/11 ONLY TO BE APPLIED BY A SIKA APPROVED CONTRACTOR Pulastic Coating-221 W 2 Component Polyurethane Construction Positioning Description Water based, 2-component polyurethane
More informationBOLON BY JEAN NOUVEL DESIGN
1 (4) INSTALLATION INSTRUCTIONS ROLLS - BOLON GREEN WELDING THE MATERIAL The material is a woven vinyl product backed with glass fiber reinforced vinyl. Since the material is a woven product, its structure
More informationINSTALLATION INSTRUCTIONS FOR ARTISAN ROLL
1 (2) The material The material is woven vinyl flooring backed with glassfibre-reinforced vinyl. Since the material is a woven product, its structure is naturally irregular. The material is not approved
More informationPol-E-Base Modified Bitumen Roof System
Pol-E-Base Modified Bitumen Roof System Specification Chemicals, Inc. produces the Pol-E-Base Built-up Roofing System as the ultimate in field applied reflective insulation roofing. It has the advantages
More informationINSTALLATION Instructions EcoFitness Interlocking Tile
Specification Data -- RESILIENT ATHLETIC FLOORING 09 65 66 INSTALLATION Instructions EcoFitness Interlocking Tile INTRODUCTORY NOTE: This installation guide is intended to provide the necessary information
More informationSlimLine Neo-Angle Base & Q-Wall-2
SlimLine Neo-Angle Base & Q-Wall-2 BASE & BACKWALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest
More informationNudo Guide Specification 03/01/2016 FiberScore FRP Wall Panels SECTION FIBERSCORE FIBERGLASS REINFORCED WALL PANELS
SECTION 09 7720 FIBERSCORE FIBERGLASS REINFORCED WALL PANELS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: Prefinished polyester glass reinforced plastic sheets and adhered to unfinished [gypsum] [cementitous]
More informationExtreme Sealing Tape
Extreme Sealing Tape Technical Data September, 2014 Product Description 3M Extreme Sealing Tape is a family of single coated, pressure sensitive adhesive tapes designed for difficult sealing applications.
More informationBENEFITS & ADVANTAGES:
APPLICATION GUIDELINES The following KARNAK Roof Restoration System is intended to be applied over sound metal roofing systems with a weathered Kynar coated metal finish. BENEFITS & ADVANTAGES: Elastomeric
More informationFLEXMAR 3-Coat High-Build Colored Quartz System
Guide Specification SECTION 09 67 23: HIGH-PERFORMANCE RESINOUS FLOORING FLEXMAR 3-Coat High-Build Colored Quartz System 20-27 mils DFT This guide specification is intended to assist the specifier in developing
More informationUSA USA USA PURE CLICK
MADE IN BELGIUM MADE IN BELGIUM 0. MADE IN BELGIUM 100 % QUALITY USA USA USA 100 100 % % QUALITY QUALITY PURE CLICK CLICK CLICK DESIGN CLICK DESIGN FLOOR FLOOR INSTALLATION MANUAL 2 Pure Click 40 is a
More informationINDOOR RUBBER FLOORING INTERLOCKING INSTALLATION / MAINTENANCE GUIDELINES MARATHON SERIES. Four-Side Interlock Loose Lay Installation
INDOOR RUBBER FLOORING INTERLOCKING INSTALLATION / MAINTENANCE GUIDELINES MARATHON SERIES Four-Side Interlock Loose Lay Installation The following pages are guidelines only... please read this manual thoroughly
More informationApplication Guide for Jotun Ultra One Powder Coatings for Engineered Wood
for Jotun Ultra One for Jotun Ultra One Powder Coatings for Engineered Wood Date of Last Revision: July 2018 Page 1 of 9 The (AG) must be read in conjunction with the relevant specification, Technical
More informationRigid Core Installation & Maintenance Instructions
Rigid Core Installation & Maintenance Instructions Suitability Rigid Core Click Vinyl Flooring is completely waterproof floating floor and has got exceptional acoustic and insulation properties due to
More informationSECTION JOINT SEALANTS PART 1 - GENERAL 1.01 RELATED DOCUMENTS
SECTION 07-9200 - JOINT SEALANTS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationWALL TILE CHARACTERISTICS. DUNES GLASS TILE
DUNES GLASS TILE Product is clear float glass with a glazed rear face. Due to the clear nature of the material some shadows may be visible at tile edge when viewed at an angle. This is not a manufacturing
More informationTufted and Woven Goods Direct Glue-Down
Tufted and Woven Goods Direct Glue-Down Installation Instructions Duraloc AIR Duraloc AIR Performance Unibond Flex Unibond Flex Bloc Unibond Laminate Unibond Plus Unibond Plus Bloc Weldlok Weldlok Bloc
More informationARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE
ARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE MANNINGTON COLORFIELDS SHEET RUBBER FLOORING Section 09 65 16 Sheet rubber Flooring (Thermoset Rubber) Created May 2012 Mannington Mills, Inc. P. O. Box
More information50948-RHN Putney. Wednesday, 29 November This document includes: Code Section Revision Dated
50948-RHN Putney Wednesday, 29 November 2017 This document includes: Code Section Revision Dated M52 Decorative papers/ fabrics 1 28 Nov 2017 Table of Contents Title Page M Surface finishes 3 M52 Decorative
More informationADA APPROVED SURFACE APPLIED DETECTABLE WARNING SYSTEM
ADA APPROVED SURFACE APPLIED DETECTABLE WARNING SYSTEM PART 1 GENERAL 1. RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Special Conditions, apply to this Section.
More informationTUFF-TAC TM BRIDGE MEMBRANE INSTALLATION GUIDE
5 pages TUFF-TAC TM BRIDGE MEMBRANE INSTALLATION GUIDE The following will describe the proper procedure to use when installing Tuff-Tac TM bridge deck membrane. The guide will cover recommended tools to
More informationAttainSilence & Attain
AttainSilence & Attain Attain 4.2mm Click over 1mm ECOsilence, Attain 4.2mm Click AttainSilence Click 4.2.1 & Attain Click 4.2 Technical Manual Installation Maintenance Warranty Manufactured in the U.S.A.
More informationQUAD Rectangular Hinged Door Shower Enclosure Installation Instructions
QUAD Rectangular Hinged Door Shower Enclosure Installation Instructions IMPORTANT Please read carefully the following instructions before installing your shower enclosure. If you have any questions on
More informationCON-DEK ICC-ES ESR-2097 SYSTEM
CON-DEK ICC-ES ESR-2097 SYSTEM Manufacturer Specifications Waterproof Deck Coating for Above Grade Concrete PART I. GENERAL 1.01 Scope A. Provide all labor, materials and equipment necessary to apply the
More informationLimited Time. Job-Ready. Value Priced.
Available for a Limited Time save money vehicle wrap bundles Job-Ready. Value Priced. In this economy, sometimes you need a little help. That s why for a limited time Oracal USA is offering special value-priced
More informationCast Stone Institute Plant Certification Program
Cast Stone Institute Plant Certification Program Company: Address: Inspector: Company Representative: Title: CSI Plant Certification Shall t Be Construed As Conferring Or Creating Any Claim, Right, Or
More information3M TM Decorative Radiant Film 76929SR
SR Product Data Sheet Product Description Date: May 2010 Supercedes : New 3M Decorative Radiant Film 76929SR is a transparent decorative pressure sensitive adhesive film incorporating 3M Radiant Light
More informationSECTION HIGH PERFORMANCE COATINGS Ramuc Type EP Epoxy Updated October 5, 2015
Specification Provided To: Date: Job: PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 09 96 60 HIGH PERFORMANCE COATINGS Ramuc Type EP Epoxy Updated October 5, 2015 A. Paints and coatings of the following
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 099600 - HIGH PERFORMANCE COATINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationACADEMIC SUCCESS CENTER THE COLLEGE AT BROCKPORT STATE UNIVERSITY OF NEW YORK PROJECT NO
SECTION 09 65 16 - RESILIENT SHEET FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationTexline Ideal loose lay
Installation Guide Texline Ideal loose lay When installed correctly Gerflor Texline s patented construction makes it an ideal loose lay solution since it does not expand or contract with changing weather.
More informationApplication Guidelines for Field-Applied Touch-up Paint Systems on Metal Panels
WHITE PAPER Application Guidelines for Field-Applied Touch-up Paint Systems on Metal Panels Introduction The information provided is intended to serve as a guide for the application of field applied air-dry
More information3M Self-Stick Liquid Protection Fabric
3M Self-Stick Liquid Protection Fabric Technical Data December 2018 3M Part Number 3M Part Descriptor 36876 3M Self-Stick Liquid Protection Fabric, 4" x 300, 6 rolls per pack 36877 3M Self-Stick Liquid
More informationArmor Plate Pipe Wrap
Armor Plate Pipe Wrap Training and Certification Course Course Elements Section 1 - Pipeline Repair Systems Section 2 - Pipeline Coating Systems Section 3 - Surface Preparation Section 4 - Required Number
More informationInstallation Instructions. Distributed by:
Installation Instructions Distributed by: 2 Carpet Installation Check off List 1. Newly poured concrete floors generally will take 30 days per 2.54cm to cure. Moisture should not exceed 2.26kg /1000sf
More informationGUIDE TO DUKKABOARD AQUA 77
GUIDE TO DUKKABOARD AQUA 77 Dukkaboard Telephone 08701 271300 support@dukkaboard.com www.dukkaboard.com Dukkaboard 2013 Issue DK1 11.13 E & OE For a totally waterproof solution, choose Dukkaboard tile
More informationTechnical Services. Product MM INCH Installation direction Seam treatment GTI CONTROL (welded) 625 X 625 mm 24.5 x 24.
INSTALLATION INSTRUCTIONS FOR GTI CONTROL TILES This document refers to the following products: Product MM INCH Installation direction Seam treatment GTI CONTROL (welded) 625 X 625 mm 24.5 x 24.5 Same
More informationGlasboard Liners. installation details. Installation Guide for Glasbord Fibreglass Reinforced Plastic (FRP) panels
Glasboard Liners installation details Installation Guide for Glasbord Fibreglass Reinforced Plastic (FRP) panels PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION These guidelines are provided
More informationGer-Eck, LLC SCRIBIL Dry Erase Clear Coat Section July 12, 2013 SECTION SCRIBIL Dry Erase Clear Coat
SECTION 09 96 66 SCRIBIL Dry Erase Clear Coat PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. General: Drawings and general provisions of the Contract, including General Conditions, Division 1 - GENERAL REQUIREMENTS,
More informationITEM 458 WATERPROOFING FOR STRUCTURES
ITEM 458 WATERPROOFING FOR STRUCTURES 458.1. Description. This Item shall govern for the furnishing and placing of waterproofing on concrete and steel bridge decks of railroad structures and on other structures
More informationA. Section Mirrors; mirrors for architectural application to receive window film.
PART 1 GENERAL 1.1 SECTION INCLUDES A. Anti-graffiti window films for glazing systems and mirrors. 1.2 RELATED SECTIONS A. Section 08300 Mirrors; mirrors for architectural application to receive window
More informationWALL TILE CHARACTERISTICS
WALL TILE CHARACTERISTICS Casabella Tile's ceramic wall material is made with white, atomized clay. All clays and minerals used within the body of the tile and surface glaze are natural and inert after
More information2.2. Jointing Jointing materials. Key facts. Sector Guide
materials Gyproc jointing materials produce a smooth, continuous, crack-resistant lining surface ready for priming and final decoration. A number of jointing specifications are available to suit the board
More informationDecorative Fiberglass Reinforced Wall Panels
SECTION 097720 DECORATIVE FIBERGLASS REINFORCED WALL PANELS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: Prefinished polyester glass reinforced plastic sheets and adhered to unfinished gypsum wallboard.
More informationInstallation guide: double-glued down installation Acoustical membranes from Tech series
Installation guide: double-glued down installation Acoustical membranes from Tech series Consult the installation guide for hardwood or engineered flooring to prepare the subfloor. It is important to have
More informationA. Section includes surface preparation and the application of high-performance coating systems on the following substrates:
ILLINOIS STATE UNIVERSITY CORDOGAN, CLARK & ASSOCIATES, INC. WATTERSON DINING EXPANSION PROJECT 960 RIDGEWAY AVENUE NORMAL, ILLINOIS AURORA, ILLINOIS CCA PROJECT NUMBER: 14362 630-896-4678 BID SET JULY
More informationARCHITECTURAL GUIDE SPECIFICATIONS
ARCHITECTURAL GUIDE SPECIFICATIONS MANNINGTON COLORSCAPE, COLORSPEC, & ONE-STEP STAIR TREADS Section 09 65 13.23 Resilient Stair Treads [Thermoset Rubber Type TS] Created November, 2008 Mannington Mills,
More information