EARLY ENTRY CUTTING PRODUCTS

Transcription

1 EARLY ENTRY CUTTING PRODUCTS Whatever It Takes GREEN CONCRETE Essential Solutions for Green Concrete Cutting

2 CC150XL-EE Early Entry Saw Gasoline 6 Blade Capacity Push Drive Features & Benefits Maximum cutting depth of 1-3/16 Heavy duty design, but light weight enough for two people to lift Cyclone air filter Easy to read built-in depth indicator Upcut design to keep debris from going back in the cut Blade raise/lower mechanical mechanism with spring loaded release Heavy duty handles offer no slack and will not rattle like competitor handles Single ribbed belt Spring loaded skid plate that keeps it down on the surface Upcut Design Specifications Blade shaft RPM: 2,600 Blade shaft diameter: 1-1/4 Arbor size: 1 with single drive pin Handle bars: Adjustable Depth indicator: Standard Made in the U.S.A. Model # Engine Make/ Model CC150XL-EE EARLY ENTRY SAW Engine Power Power Source Part # Blade Capacity Product Weight (lbs) CC148HXL-EE6 Honda GX HP, 7.6 Torque (lbs.-ft.) Gas CC165BVXL-EE6 Briggs Vanguard 6.5 HP Gas CC165LXL-EE6 Lifan LF168F 6.5 HP Gas Joint protectors for use when making cross-cuts in green concrete (2 Long x 1/2 Wide x 1/8 Thick) CC150XL-EE OPTIONS Description Part # Joint protectors - for use when making crosscuts in green concrete (bag of 50) JOINTPRO Catalytic muffler for Honda GX Parts List #: Operator Manual #:

3 Gasoline CC190XL-EE Early Entry Saw 14 Blade Capacity Self Propelled Drive Features & Benefits Maximum cutting depth of 3 with 14 blade Capable of.110 to.250 thick blades Heavy duty handle design Self aligning blade shaft bearings Handles can be pointed in or out for operator ease and comfort Easy access to battery with heavy duty battery isolator switch to prevent battery drain Upcut design to keep debris from going back in the cut Lifting hook for easy transport Spring loaded skid plate that keeps it down on the surface Upcut Design Specifications Blade shaft RPM: 3,500 Blade shaft diameter: 1-1/4 Arbor size: 1 with single drive pin Blade raise/lower: Electric actuator Transmission: Eaton Model 6 Drive Speed: 0-80 feet per minute Handle bars: Includes: Adjustable Electric start, low oil alert and tach/hour meter Made in the U.S.A. Model # Engine Make/ Model CC190XL-EE EARLY ENTRY SAW Engine Power Power Source Part # Blade Capacity Product Weight (lbs) CC190HXL-EE Honda GX HP, 35.6 Torque (lbs.-ft) Gas Parts List #: Available April, 2015

4 FIRST CUT BLADES For Use on Diamond Products or Competition Style Saws Dry cutting product GREEN CONCRETE GOOD Star Blue - GOOD QUALITY, LONG LIFE C45BM C45CBM C52BM C980BM C55BM C60BM 6 x x x x x x x x x x x H D P BETTER BEST Consider the aggregate in your area and cure time before determining the bond specification. Color codes do not refer to the aggregate map color codes found on page 8 Soff-Cut is a registered trademark of Husqvarna AB (publ) and is in no way affiliated with Diamond Products Limited. Heavy Duty Orange - VERY HIGH QUALITY, LONGER LIFE C45HM C45CHM C52HM C980HM C55HM C60HM 6 x x x x x x x x x x x x x x These specifications are similar to our wet walk behind blades, but can be used dry in early entry applications due to the segments being laser-welded on the core. Premium Black - HIGHEST QUALITY, LONGEST LIFE C45PM C45CPM C52PM C980PM C55PM C60PM 6 x x x x x x x x x x x x x x Soff-Cut Specification FIRST-CUT BLADE CROSSOVER Diamond Products Specification To Use: Aggregate Hardness Purple C45 Hard Green C45C Medium Hard Red C52 Medium Orange C980 Medium Soft Yellow C55 Medium Black C60 Soft Includes 1 arbor with triangle knock-out

5 GREEN CONCRETE Dry cutting product FIRST CUT BLADES With Skid Plate For Use on Diamond Products or Competition Style Saws C45BM Star Blue with Skid Plate C45CBM C52BM C980BM C55BM C60BM 6 x x x x x x x x x x x C45HM Heavy Duty Orange with Skid Plate C45CHM C52HM C980HM C55HM C60HM 6 x x x x x x x x x x x C45PM Premium Black with Skid Plate C45CPM C52PM C980PM C55PM C60PM 6 x x x x x x x x x x x H D P FIRST UT First Cut Blades with Packaged Skid Plate Arrive in a Sale-Ready Clamshell Includes 1 arbor with triangle knock-out

6 COMPETITION-STYLE SKID PLATES Dry cutting product Stainless steel construction 1/8 thick bottom plate allows skid to be used for an average of 3 blades before requiring replacement depending on the abrasive properties of the aggregate and the diameter of the blade Steel mounting pins that won t break or fails like some cast aluminum competitor mounts Mounted with a locking pin to keep the plate in place Fits both steel and cast skid plate saws Available in these sizes: For use on Diamond Products or Soff-Cut saws When Used with Hard Aggregate: Blades in hard aggregate have shorter life so the skid plate will last longer. This holds true for small diameter blades - they wear out faster so the skid plate last through more blades. When Used with Soft Aggregate: Blades in soft aggregate last longer so the skid plates wear out with fewer blades. Blades specifications for soft aggregate are typically hard which results in more skids plates being needed. SKID PLATES FOR SOFF-CUT SAWS (FOR.125 &.250 THICK BLADES) Description.125 Part # Part #.250 Skid Plate for 6 and 8 Blades Skid Plate for 10 Blades Skid Plate for 12 and 13.5 Blades Skid Plate for 14 Blades Skid plates for.375 and.500 thick blades available upon request. Soff-Cut is a registered trademark of Husqvarna AB (publ) and is in no way affiliated with Diamond Products Limited.

7 GREEN CONCRETE Dry cutting product EARLY ENTRY BLADES 1 Arbor Star Blue Good quality diamond and good cutting value in green concrete Three bonds for different aggregate types Star Blue Entry-Cut Blades EC100B EC200B EC300B 6 x.100 x Entry-Cut blades have a 1 arbor and drive pin hole that can be used on our CC150XL-EE or other standard, low HP walk behind saws P Premium Black Highest quality diamond and longest cutting life in green concrete Three bonds for different aggregate types 1 Arbor Premium Black Entry-Cut Blades EC100P EC200P EC300P 6 x.100 x ENTRY-CUT SPECIFICATIONS EC100 - Soft bond for hard aggregate EC200 - Medium bond for medium aggregate EC300 - Hard bond for soft abrasive aggregate H D Heavy Duty Orange Early Entry Blades Early Entry blades best suited for use on Core Cut CC1000 saw 1 Arbor 1 arbor with drivepin hole Three bonds to choose from for green concrete GCS100H - Soft bond for hard aggregate GCS200H - Medium bond for medium aggregate GCS300H - Hard bond for soft abrasive aggregate HEAVY DUTY ORANGE EARLY ENTRY GREEN CONCRETE BLADES GCS100H GCS200H GCS300H 8 x.100 x x.125 x x.250 x Joint Spacers 50 per bag 2 long x 1/2 wide x 1/8 thick Used when making cross-cuts in green concrete Part # JOINTPRO

8 U.S. & CANADA Soft Limestone AGGREGATE MAP Sandstone Pit Gravel Dolomite Limestone Limestone Siliceous Dolomite Soft Shell SOFT Medium Hard River Rock Granite Medium Traprock Hard Chert Slate Quartz Traprock Decomposed Granite Flint Rock Basalt Medium Crushed Gravel MEDIUM MEDIUM SOFT Hard River Rock Quartzite MEDIUM HARD HARD EARLY ENTRY BLADE SPECIFICATIONS FIRST Aggregate Hardness (See map) UT These are the basic aggregates found in the shown areas. Other types of aggregate can be found in many parts of the U.S. and Canada WHAT ARE EXPANSION/CONTROL JOINTS? Concrete expands and contracts with temperature and moisture changes...as the temperature rises or the moisture content of the concrete increases, expansion takes place...as the temperature drops, the concrete will contract. The provision to accommodate movement at predetermined locations with proper joint cuts, prevents the development of stresses that could rupture the concrete. Uncontrolled Cracks Concrete Without Expansion/Control Joint Without a cut or joint made into the material, heat and cold aligned with curing can cause expanding and contracting of the concrete, creating uncontrolled cracks throughout. Those cracks will eventually create ruptures and sections that can pull apart from the rest of the material. Diamond Products Limited 333 Prospect Street Elyria, Ohio U.S.A Fax: FIRST-CUT SPECIFICATION C45/C45C C52 C980 C55 C60 Expansion/ Control Joint ENTRY-CUT SPECIFICATION EC100 EC100 EC200 EC200 EC300 Hard Medium Hard Medium Medium Soft Soft Controlled Cracks Concrete With Expansion/Control Joint Making a controlled cut in the concrete CONTROLS where the cracks appear. When this procedure is done in determined spaced sections, the damage and cracking is kept at a minimum which prolongs the life of the concrete slab.