GRASSELLO DI CALCE BIANCO Natural mineral calcium dyoxide at long aging, which lays to a glossy finish
|
|
- Arleen Cannon
- 6 years ago
- Views:
Transcription
1 Destination Indoor and outdoor decoration of buildings evn of those with particular historicartistic importance. Even if it reaches a high thickness layer, it has a high breathability Characteristics Readytouse Antibacterial Adherence to mineral supports BREATHABLE Good light resistance VOC (Directive 2004/42/CE) ( g/l ) 200 <Decorative effects paintings.eu limit value for this product (Cat. A/l): 220g/l (2010). This product cointans max. 200 g/l Recommended surface and temperature conditions Avoid applications at room temperatures lower than +10 C or higher than +3 C and relative humidity higher than 80%. Check the surfaces suitability referred to the humidity degree with hygrometer. Support temperature: min +10 C, max +3 C. Avoid application on chalking surfaces if not peviously treated with fixatives model FIXODIL for outdoors or Acrilan 3470 for indoors. WARNING:ventilate the room to avoid humidity accumulation. WARNING:the maximal washability is obtainable after 710 days from application. Completely eliminate preexistent solvent paintings. Remove, wet sanding or brushing, the possible efflorescences. In presence of moulds, use antimolds detergents and fixing elements. Reccomendations Well mix the product before use The applications must not be executed on walls directly exposed to the sun or with room temperatures under + C. In case of doubt, with old chalking or just a little cohesive paintings, evaluate the first coat dillution. Apply the fixative primer on a little surface portion and after at least 12 hours make an adhesion test. It is recommended to apply the product in favorable weather conditions, as inadequate weather conditions could negatively affect the drying conditions by compromising the optimal achieving of the product aesthetic characteristics and performances. Page 1/
2 Application cycle Never painted interior walls In case of new civil plasters let it age for at least 28 days (T= 20 C and UR< at7%) ) before any operatin. Carefully brush. Remove bad anchored parts, dust and dirt. level imperfections with STUCOL. After 8 hours level the stuccoed parts and clean them carefully. Be sure that the wall is perfectly dry. Verify surface idoneity according to humidity degree with match test or hygrometer. If necessary, consolidation with water fixative as ACRILAN In case of chalking supports use solvent fixative as FIXODIL, otherwise use the following modalities. If the support does not need fixative, it is anyway recommended to moisten it, to avoid the wall to subtract excessively water from the binder. After 24 hours from fixative application apply a first layer of GRASSELLO DI CALCE. After at least 12 hours apply one more layer to create the adequate thickness. After at least 12 hours sand to remove possible imperfections, then remove dust and apply little quantities of material compacting and polishing it (with inox trowel) beofre it dries completely. Clean the tools withh water after use. Already painted interior walls with tempera paintings Carefully clean the surface from dust or dirt. With molds or fungi disinfect the surfaces with SESTRICID. Level imperfections with STUCOL. After 8 hours sand the stuccoed parts and clean them carefully. Insulate the whole surface with solvent fixative as FIXODIL. After 24 hours apply a first layer of GRASSELLO DI CALCE or marmorino. After at least 12 hours apply one more product layer to cerate the adequate thickness. After at least 12 hours sand to remove possible imperfections, then remove the dust and apply little quantities of material, compacting and polishing it (with inox trowel) before it dries completely. Clean the tolls withh water after use. Page 2/
3 Application cycle Already painted interior walls with washable hydropaintings Carefully clean the surface from dust or dirt. With molds or fungi disinfect teh surfaces with SESTRICID. Level imperfections with STUCOL. After 8 hours sand the stuccoed parts and clean them carefully. Be sure that the wall is perfectly drt. Verify surface idoneity according to humidity degree with match test or higrometer. In case of much chalking supports use solvent fixative as FIXODIL. After 24 hours apply a first layer of GRASSELLO DI CALCE or marmorino. After at least 12 hours apply one more layer to give the adequate thickness. After at least 12 hours wet sanding to remove possible imperfections, then remove the dust and apply little quantities of material, compacting it and polishing it (with inox trowel) before it completely dries. Clean the tools with water after use. Never painted exterior walls In case of new civil plasters let age for at least 28 days( T= 20 C and U.R. < at 7%) before any operation. Carefully brush. Remove badanchored parts, dust and dirt. Level imperfections with special plasters. Wait the drying times and sand the stuccoed parts and clean them carefully. Be sure that the wall is perfectly dry.. Verify surfaces idoneity according to humidity degree with match test or higrometer. If necessary, use water fixative for solidification as ACRILAN If the support does not need fixative, it is recommended to moisten it, to avoid that the wall subtracts excessively the watre in the binder. Apply a first coat of product diluted at 3 40%. After at least 4 6 hours apply a second layer of prodct diluted at 30 3%. Already painted exterior walls Completely remove the old organic paintings as synthetic ones, washable quartz, tempera and plastic coatings. Carefully clean the surface from dust or dirt. With molds or fungi disinfect the surfaces with SESTRICID. Level imperfections with STUCOL. After 8 h sand the stuccoed parts and clean them carefully. Be sure that the wall is perfectly dry. Verify surfaces idoneity according to humidity degree with match test or higrometer. If necessary, use water fixative for solidification as ACRILAN If the support does not need fixative, it is recommended to moisten it, to avoid that the wall subtracts excessively the watre in the binder. Apply a first coat of product diluted at 3 40%. After at least 4 6 hours apply a second layer of prodct diluted at 30 3%. Page 3/
4 Characteristics and technical informations Tin aspect RESIN Color Use Data observable at T=20 C and 60% relative humidity Tixotropic White White suitable for tintometric system MW2 Adherence to mineral supports Spatula Thinner Tools' cleaning Application process Water Water Brush Thinner (% Volume) TECHNICAL DATA Complete polymerisation days Recoating interval ( h ) Minimum film temperature ( C ) Notice Mass density ( kg/l ) Solids content by vol. ( % ) Brooklfield viscosity (cp) Brilliance ( % ) Touch dry ( h ) Depth dry ( days ) recommended dry film thickness (dtf) ( µm ) Theoretical spreading rate ( mq²/lt ) Data refer to the product mixed at 20 C. 1, (kg/m²) Glossy Page 4/
5 STORAGE (dry and cool place) 12 months in tightly closed package, protected from frost and heat sources Storage temperature ( C) Unit size 23 kg Safety instructions Products must be treated with attention, avoid the skin contact. Users will have to follow the actual laws. Actions as wet sanding, sanding, removal with flame, etc. of old painting coats can geerate dust and dangerous smokes. Work in well areated areas and wear the adequate individual protection means. In Italy Decree 303 and 47 concern the rules valid for the application operations. For further information concerning the right product elimination, storage and manipulation please consult the relative taìechnical data sheet. Data in this technical sheet are only given for information and are the result of laboratory tets and practical experience, However, the factory is not responsible if the product isn't used under its direct control. SESTRIERE VERNICI Srl Technical Assistance is available to give all information necessary for a correct use of the product. Be careful: the product could show, towards some subject who are particularly sensitive to isothiazolones, a little irritation. It's thus recommended to use gloves and protective glasses and to wash very well the parts which could by chance touch the skin. Page /
AK40 PRIMER ACRILICO HS Two-component acrylic monolayer primer
Twocomponent acrylic monolayer primer Revision 2 fro 1/01/201 Converter name AK40 Destination Primer with excellent adherence on steel, galvanised steel, aluminium, light alloys. Suitable as first coat
More information4970 PRIME COAT FZ Two components zinc phosphate epoxy product
Converter name Destination Extremely versatile use: industrial vehicles, agricultural machines, different metal surfaces, (trussing, external pipes). Contains zinc phosphate as anticorrosive pigment. Doesn
More informationTECHNICAL DATA SHEET
TECHNICAL DATA SHEET TRAVERTINO ROMANO Technical Qualities TRAVERTINO ROMANO by Oikos is a special, ready to use, decorative plaster for interiors and exteriors, created using sand, selected marble grains
More informationMITHOS LUX is a traditional self-polishing Venetian lime putty-base stucco for interiors
MITHOS LUX Product data sheet: VID455150T Rev. 02 dated 06/09/2018 Name Description Product characteristics VOC Classification (Volatile organic compounds) Directive 2004/42/EC MITHOS LUX Traditional Venetian
More informationTechnical Data Sheet
MATTE CONTRACTOR CHOICE PAINT The Matte Contractor Choice C paint is designed for the contractor; it has good performance and opacity. No odor. Has very good brushability, leveling, durability, adhesion
More informationTechnical Data Sheet
ART OF COLOR EGGSHELL PAINT The Art of Color products line, because of the high quality of its raw materials, leaves a nice matte finish, while providing maximum performance. This coating has a low VOC
More informationProperty Test/Standard Description. Flash point ISO 3679 Method C
Other Technical Data Sheet 2906;2907 6 2906 VValidationDate). 1 Product description This is a two component finishing filler. It is a smooth multi purpose product. It has good sanding properties, strong
More informationApply a very thin single coat of NATURWAX using a cloth, pad, or trowel.
NATURWAX Product data sheet: VID455171T Name Description Product characteristics NATURWAX Natural protective wax for spatulates and stuccos. NATURWAX is a natural wax-base protective coating that is ideal
More informationTechnical Data Sheet Rhenopox EB 06.1 Art. no.: A 5198
version: 2016/06 page 1 of 5 Rhenopox EB 06.1 (2k Epoxy Color Traffic Zone) component A Art. no.: A 5198 - Products consist of a mixture of component A = Rhenopox EB 06.1 and component B = Rhenopox EH
More informationDMS EP-D80 Broadcasted Epoxy Resin Floor
Product description DMS EP-D80 system is a three component epoxy system, designed as epoxy binder containing special fire retardant additives and mineral fillers, such as quartz or granulated granite.
More informationProperty Test/Standard Description Solids by volume. ISO 3233 Flash point ISO 3679 Method C
Other Technical Data Sheet 2902;2903 6 2902 VValidationDate). 1 Product description This is a two component fairing compound/filler. It is an ultra lightweight, very flexible, solvent free product. It
More informationPROTEX WB Eco-friendly, water-based, easy to apply impregnating sealer to protect natural stone against rising damp and stains.
Eco-friendly, water-based, easy to apply impregnating sealer to protect is a high-performance impregnating treatment to protect natural stone against staining and the harmful effects of water and rising
More informationData Sheet Eco-Smart Membrane WS M1
Water-based Acrylic WS M1 Elastomeric Waterproofing Membrane is a durable, multi-use, extremely durable acrylic coating. At an ideal wet film thickness of 10-14 mils per coat (8-10 mils dry film finish
More informationEpoxy Based, Two Component, Grouting Filling and Ceramic Adhesive Resistant to Chemicals and Bacteria
MasterTile EPO 700 (Formerly known as Epofuga (Formerly known as Mastertile 700) ) 700 Epoxy Based, Two Component, Grouting Filling and Ceramic Adhesive Resistant to Chemicals and Bacteria Description
More informationProduct Cod. HIGH RESISTANCE SELF-LEVELING COMPOUND BASED ON POLYURETHANE RESINS IN WATER DISPERSION AND HYDRAULIC BINDERS.
Product Cod. HIGH RESISTANCE SELF-LEVELING COMPOUND BASED ON POLYURETHANE RESINS IN WATER DISPERSION AND HYDRAULIC BINDERS. Features Fast curing. Excellent wide range chemical resistance. High mechanical
More informationApproved. This product is tintable in a wide range of colours in Jotun's Multicolor Decorative (MCD) system. Property Test/Standard Description
Approved 12660 1,2 12660 Acrylic emulsion ^(ValidationDate) 1 Product description This is a one component water borne acrylic emulsion coating. It is a versatile, fast drying product for exterior and interior
More informationBTM BT2K 600. Areas of Use
BTM BT2K 600 Bitumento BT2K 600 is a solvent-free, two-component, elastic, water-based, fiber reinforced, rubber and cement based bitumen waterproofing material. Areas of Use As water and moisture tight
More informationExterior pipes, Fences, screens, grills and gates, Metallic Structures, Structural elements (column, trusses, etc.)
DESCRIPTION ZINC-TECH GALVANIC is a single component zinc-rich anticorrosive, made from synthetic resins and pigments that allow it to provide an excellent cathodic protection against corrosion. Has galvanizing
More information1 ST KOTE HI COVER PVA
1 ST KOTE HI COVER PVA DESCRIPTION: Superior coverage, quality acrylic resin and easy application makes Powafix 1 st Kote the right choice when painting walls and ceilings. You can be assured that when
More informationJSCE-K Test methods for weathering resistance of. concrete surface coating materials
JSCE-K 511-2007 Test methods for weathering resistance of concrete surface coating materials JSCE-K 511-2007 Test methods for weathering resistance of concrete surface coating materials 1. Scope This JSCE
More informationApprox. 12 m² per litre depending on surface porosity, profile. Application methods
TECHNICAL DATA SHEET Version 1 2015 JUNE THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION Versatile multi-surface waterborne primer PRODUCT USES Suitable for use as a primer to appropriately
More informationProperty Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)
Approved 343 1,2 343 alkyd ^(ValidationDate) 1 Product description This is a one component oxidatively drying alkyd coating. Can be used as primer or mid coat in atmospheric environments. Suitable for
More informationConcrete Paint and Varnish
www.teknos.com DATA SHEET 1247 12 22.02.2017 TEKNOFLOOR AQUA 110F Concrete Paint and Varnish PAINT TYPE USAGE SPECIAL PROPERTIES TEKNOFLOOR AQUA 110F Concrete Paint is a water-based, two-pack epoxy paint.
More informationStormshield Self-Cleaning Masonry
Stormshield Self-Cleaning Masonry Johnstone s Stormshield Self-Cleaning Masonry has been formulated using groundbreaking nano technology in order to give an extremely smooth and dirt resisting finish.
More informationCarboguard 890 PRODUCT DATA SHEET SELECTION & SPECIFICATION DATA. Generic Type. Cycloaliphatic Amine Epoxy
SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Cycloaliphatic Amine Epoxy Highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all industrial
More informationData sheet Armatop A - new / Page 1. Areas of application Bonding Bonding of mineral wool, polystyrene and cork external wall insulation boards.
Data sheet Armatop A - new / Page 1 Armatop A - new Bonding and reinforcing compounds for alsecco external wall systems Areas of application Bonding Bonding of mineral wool, polystyrene and cork external
More informationHAMMERITE NO. 1 RUST BEATER PRIMER
TECHNICAL DATA SHEET Version 2 2018 June THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION Hammerite No.1 Rust Beater provides a high build finish to heavily pitted areas of rust and
More informationSYSTEMDATENBLATT Sika Cable-System
-System CORROSION PROTECTION FOR BRIDGE CABLES OF STEEL AND GALVANIZED STEEL DESCRIPTION The -System consists of 4 coating materials as well as a sealant and a injection material. Suitable for coating
More informationTECHNICAL INFORMATION SWARCO UV-LINE Paint
TECHNICAL INFORMATION SWARCO UV-LINE Paint SWARCO UV-LINE Paint Content 1 Main characteristics / Field of application... 3 2 Technical Data... 3 3 Processing instructions... 4 3.1 Training... 4 3.2 Colored
More informationProperty Test/Standard Description STANDARD GRADE
Other Technical Data Sheet 525;527;1549 1,2 525 epoxy mastic VValidationDate). 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids,
More informationData Sheet 3631 Englisch
Englisch Silicate Render KR Silikat-Putz Mineral decorative render, in scraped render structure, for exterior use Properties Decorative, easy structurable facade render silicate based with organic stabilizers
More information1(5) Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
1(5) A two-component, resin modified epoxy paint. Excellent resistance to abrasion, chemicals and water immersion Used as a primer or finish for interior and exterior steel, aluminium and zinc surfaces
More informationGeneral: Primarily designed for maintenance and repair. Only aluminium containing versions to be used in immersed environments.
Other Technical Data Sheet 5580;5660;6520;10760 1,2 5580 epoxy mastic VValidationDate). 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high
More informationMATERIA Water- based epoxy resin, for the decoration of floors and walls with a limitless effect.
pag. 1 of 5 MATERIA Water- based epoxy resin, for the decoration of floors and walls with a limitless effect. General Features MATERIA is a coatings, based on epoxy resins, for the decoration of floors
More informationPre-qualification testing in accordance with NORSOK M-501, Rev. 3/4, System 7, suitable for splash zone. Property Test/Standard Description
Approved 390;21780;21840 1,2 390 unsaturated polyester ^(ValidationDate) 1 Product description This is a styrene free glass flake reinforced unsaturated polyester coating. It is an ultra high build, extremely
More informationProperty Test/Standard Description. 96± 2 % matt (0-35) Flash point ISO 3679 Method 1 34 C
Approved 388;26160 1,2 388 unsaturated polyester ^(ValidationDate) 1 Product description This is a glass flake reinforced unsaturated polyester coating. It is an ultra high build, extremely abrasion resistant
More informationThis product contributes to the Green Buildings Standard credits. Please see section Green Building Standards.
Approved 12660 1,2 12660 Acrylic emulsion ^(ValidationDate) 1 Product description This is a one component water borne acrylic emulsion coating. It is a versatile, fast drying product for exterior and interior
More informationData Sheet 832 Englisch
Englisch Primer LF 832 Floortec 2K-Epoxi-Grund LF 832 solvent-free, transparent primer resin as primer in Floortec PUR Coating System and under Floortec 2C Epoxy Thick Layer LF 834 Properties Solvent-free,
More informationProperty Test/Standard Description STANDARD GRADE
Other Technical Data Sheet 4860;523;527;1549 1,2 523 epoxy mastic VValidationDate). 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids,
More informationSATIN NON-DRIP ACRYLIC
PRODUCT DATA SHEET ISSUE DATE: FEBRUARY 2016 PRODUCT DESCRIPTION PRODUCT NAME PRODUCT DESCRIPTION SATIN NON-DRIP ACRYLIC A tough superior quality non-drip waterborne enamel with a satin sheen finish. A
More informationProperty Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1
7461;7680 1 7680 zinc silicate VValidationDate). 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high solids, high zinc dust containing product. It conforms
More informationProperty Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method 1 30 C calculated VOC-USA / VOC Hong Kong EPA Method 24
Other Technical Data Sheet 3140;3240;4320 1,2 3140 polyurethane VValidationDate). 1 Product description This is a two component chemically curing aliphatic acrylic polyurethane coating. It has a gloss
More informationvinyl ester Property Test/Standard Description semi gloss (35-70) Flash point ISO 3679 Method 1 34 C calculated IED (2010/75/EU) (theoretical)
Approved 408;21800;21820;21740;21760;21840 1,2 408 ^(ValidationDate) 1 Product description This is a glass flake reinforced coating. It is an ultra high build, extremely chemical resistant and fast curing
More informationImron HydroClearCoat. 2K Waterbased Clearcoat PUR. Technical Data Sheet. Description
Description Imron HydroClearCoat HC300 is a waterbased 2-component polyurethane clearcoat especially developed for application on all types of commercial vehicles. Composition based on acrylic resin. Products
More informationPRODUCT CATALOGUE PRODUCT CATALOGUE.
PRODUCT CATALOGUE PRODUCT CATALOGUE www.betekexport.com Betek Boya Kimya ve Sanayi A.Ş., founded in 1988, in the early years of its entrance into the sector, has developed high quality products at concrete
More informationProperty Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (28 C) VOC-USA / VOC Hong Kong EPA Method 24
1505;1506 1 1505 novolac epoxy VValidationDate). 1 Product description This is a two component polyamine cured novolac epoxy coating. It is heat resistant up to 392 F (200 C) and can be applied on hot
More informationCHARACTERISTICS / ADVANTAGES. Yellowish-transparent. PACKAGING 20 kg per pail
PRODUCT DATA SHEET Epoxy-resin binder for priming, levelling mortar and for screeds PRODUCT DESCRIPTION Sikafloor -156 is a colourless, 2-component low viscosity epoxy resin. USES For priming and levelling
More informationApproved. Marine: Exterior areas, specially designed for outside hull, may be used on superstructure, decks and other external areas.
Approved 1055;1063 1,2 1055 vinyl epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured vinyl epoxy based coating. Specially designed as a tie coat between epoxy primers
More informationProperty Test/Standard Description. semi gloss (35-70) Flash point ISO 3679 Method 1
2080;2081 1 2080 epoxy VValidationDate). 1 Product description This is a two component polyamide cured epoxy coating. It is a high solids, high build product. Designed as a mid coat in systems for new
More informationRed Insulating Varnish 4228 Technical Data Sheet 4228-Liquid
Description Our 4228 Red Insulating Varnish is a highly insulating coating with excellent arc and corona resistance. This low viscosity, one part varnish coating is easy to use and adheres well to many
More informationMarine: Exterior and interior areas, including outside hulls, superstructures, decks, cargo holds and water ballast tanks.
478;479;4060 1,2 478 epoxy VValidationDate). 1 Product description This is a two component amine cured pure epoxy coating. It is a fast drying, abrasion resistant, high solids, high build product. Designed
More informationApproved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method C calculated VOC-US/Hong Kong. US EPA method 24 (tested)
Approved 28780 1,2 28780 acrylic ^(ValidationDate) 2 Product description This is a one component water borne acrylic emulsion coating. It is a versatile, fast drying product for exterior and interior use.
More informationProperty Test/Standard Description
Approved 1537 1,2 1537 alkyd ^(ValidationDate) 1 Product description This is a one component oxidatively drying alkyd coating. It is a fast drying, high build, zinc phosphate pigmented product. Can be
More informationSpeical, substrate-tolerant primer
Speical, substrate-tolerant primer Availability Quantity per pallet 120 Packaging unit 2,5 kg 10 kg 25 kg Type of container Tin bucket Tin bucket Container code 03 11 26 Art. no. 0916 6364 See application
More informationPRODUCT DESCRIPTION PROCESSING
5108000030 ff Water-based thick-film metallic wood glaze for wooden windows and front doors for industrial and professional use It has been matched as a system with a 3-coat structure PRODUCT DESCRIPTION
More informationFor purchasing information visit: Sikkens Cetol Novatech
The following Technical Datasheet is provided by Manns Wood Finishes Direct cannot be held liable for the information contained within this document. For purchasing information visit: Sikkens Cetol Novatech
More informationPRODUCT INFORMATION SABRESHIELD
PRODUCT DATA SHEET ISSUE DATE: JULY 2015 PRODUCT INFORMATION PRODUCT NAME PRODUCT DESCRIPTION SABRESHIELD A heavy-duty, fibre- reinforced, waterproof coating with unique dirt shedding technology, excellent
More informationPre-qualification testing in accordance with NORSOK M-501, Rev. 3, System 7, suitable for splash zone. Property Test/Standard Description
Other Technical Data Sheet 574;576 1,2 574 epoxy VValidationDate). 1 Product description This is a two component polyamine cured epoxy coating. It is a high solids, high build, glass flake reinforced product.
More informationMARMOCRYL SILICONE Fine
Technical Datasheet Fine Silicone, pasty, ready-to-use render Smooth finish White or colored Water-repellent Description Fine is a ready-touse, pasty, white or colored, silicone acrylic render. It consists
More informationCUSTOM BRICK. Custom Brick Finish Polymer System Specifications For Use On Vertical Walls DS151. Architectural Finish for Use on Vertical Walls
CUSTOM BRICK Architectural Finish for Use on Vertical Walls Custom Brick Finish Polymer System Specifications For Use On Vertical Walls PART I- GENERAL DRYVIT SYSTEMS, INC. MANUFACTURER S SPECIFICATION
More informationProperty Test/Standard Description. calculated US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)
Approved 2124;7720 1,2 7720 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc epoxy coating. It provides corrosion protection as part of a complete coating
More informationIONTRA DENEB , CATALOG
DENEB joint-stock company shop and office: 1756 Sofia 115, Sv. Kliment Ohridski blvd. tel.: +359 2 816 76 60 fax: +359 2 816 76 37 sales@denelbg.com deneb@denelbg.com WWW.DENEL.BG PRO INTRA CATALOG DENEB
More informationWhite, a range of ready-mixed colours, and colours from the Dulux Colour System
TECHNICAL DATA SHEET Version 2 2016 SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION High quality interior or exterior matt finish PRODUCT USES Recommended for exterior and
More informationCUSTOM BRICK. Custom Brick Finish Polymer System Specifications For Use On Vertical Walls DS151. Architectural Finish for Use on Vertical Walls
CUSTOM BRICK Architectural Finish for Use on Vertical Walls Custom Brick Finish Polymer System Specifications For Use On Vertical Walls PART I- GENERAL DRYVIT SYSTEMS, INC. MANUFACTURER S SPECIFICATION
More informationDULUX INTERIOR LUXURIOUS SILK TECHNICAL DATA SHEET Version SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS
TECHNICAL DATA SHEET Version 1 2016 SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION A low odour premium quality interior mid sheen finish with supreme stain resistance. PRODUCT
More informationTECHNICAL DATA SHEET
Page 1of 5 PRODUCT DESCRIPTION PROPERTIES COLOUR GLOSS LEVEL WEATHERING UT100 2-Pack topcoat is an unmodified acrylic polyurethane designed to maintain maximum appearance for the maximum length of time.
More informationProperty Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)
Approved 23660 1,2 23660 silicone acrylic ^(ValidationDate) 1 Product description This is a one component physically drying silicone acrylic coating. It is an aluminum pigmented product. It is heat resistant
More informationDOWSIL ALLGUARD Silicone Elastomeric Coating
Technical Data Sheet Water-based silicone elastomer for waterproofing above-grade exterior masonry substrates Features & Benefits Provides long-term waterproofing protection Maintains water protection
More informationProperty Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method F (35 C) VOC-USA / VOC Hong Kong EPA Method 24
1169;1170 1,2 1169 epoxy VValidationDate). 1 Product description This is a two component polyamide cured high molecular weight epoxy coating. It has a gloss finish with fair gloss retention. To be used
More informationDULUX WEATHERGUARD FINE TEXTURED
TECHNICAL DATA SHEET Version 1 2016 JULY THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION A tough, durable exterior coating with Maxiflex that provides lasting elasticity to cover hairline
More informationRed Insulating Varnish 4228 Technical Data Sheet 4228-Liquid
Description Our 4228 Red Insulating Varnish is a highly insulating coating with excellent arc and corona resistance. This low viscosity, one-part varnish coating is easy to use and adheres well to many
More informationGULF COAST PAINT MFG., INC
MCU-100 PRIMER/FINISH MOISTURE CURED URETHANE ALUMINUM COATING PRODUCT DESCRIPTION A one component, Moisture Cured Polyurethane Aluminum Coating. Has excellent adhesion to sound, tightly adherent rusty
More informationProperty Test/Standard Description Solids by volume. ISO 3233 Gloss level (60 ) ISO 2813
Other Technical Data Sheet 2063;2064 1,2 2063 epoxy VValidationDate). 1 Product description This is a two component solvent free polyamine cured epoxy coating. It is a general purpose tank lining with
More informationProperty Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)
Approved 3140;3240;4320 1,2 3140 polyurethane ^(ValidationDate) 1 Product description This is a two component chemically curing aliphatic acrylic polyurethane coating. It has a glossy finish with very
More informationProperty Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)
Approved 402;2522 1,2 2522 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high zinc dust containing product. It conforms to
More informationBONDEX Premium Product Code Product Name Recommended for Available sizes
BONDEX Premium Product Code Product Name Recommended for Available sizes 330045 Bondex Premium All types of indoor and outdoor wood 0.75 L - 2.50 L 1 Product Description 1.1 Product Type: 1.2 Manufacturer:
More informationDiescolith SOL-Silikat
Highly diffusible SOL silicate paint according to DIN 18363 Silica sol silicate base Tribrid formula Variety of applications Highly weather-resistant Highly water-repellent Highly diffusible UV-light-resistant
More informationProperty Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)
Approved 16561;16840;18880 1,2 18880 epoxy mastic ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, abrasion resistance, high
More informationTwo component solvent-free epoxy system for creation of self-levelling floors. Gloss <4% <70% IR4
Two component solvent-free epoxy system for creation of self-levelling floors Fields of Application Epoxol Floor S is a suitable screed that can be applied on cement-based floors which need high mechanical
More informationProperty Test/Standard Description. calculated US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)
Approved 23680;1551 1,2 23680 epoxy mastic ^(ValidationDate) 1 Product description This is a two component amine cured epoxy mastic coating. It is a surface tolerant, high solids product. It is aluminum
More informationCOOL BARRIER RESIST* High Solar Reflective Water Resistant Flexible Dust Resistant Waterbased
High Solar Reflective Water Resistant Flexible Dust Resistant Waterbased Energy Savings Energy Thermal Savings Comfort Thermal Comfort Weather Resistance Weather Resistance Long Term Resist* ion Long Term
More informationProperty Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 28 C
Other Technical Data Sheet 1505;1506 1 1505 novolac epoxy VValidationDate). 1 Product description This is a two component polyamine cured novolac epoxy coating. It is heat resistant up to 200 C and can
More informationProperty Test/Standard Description
Approved 18940;18941 1,2 18940 acrylic ^(ValidationDate) 1 Product description This is a two component chemically curing modified acrylic coating. The product does not contain isocyanates, neither does
More informationMicastone Coating System
40-year R&D Experience Micastone System Multi-Colour Stone Finishing Bonntile Hong Kong Limited Flat C2, 11/F, Hang Fung Industrial Building Phase 2, 2G Hok Yuen Street, Hung Hom, Kowloon, Hong Kong (+852)
More informationData sheet Armatop MP / Page 1
Data sheet Armatop MP / Page 1 Armatop MP Bonding and reinforcing compounds for alsecco external wall systems Areas of application Bonding Bonding of ecomin-por, mineral wool, polystyrene and cork exterior
More informationTested in accordance with ISO , high expected durability in corrosivity category C5-I. Property Test/Standard Description
Approved 7461;7680 1,2 7680 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high solids, high zinc dust containing product. It
More informationPRODUCT DATA SHEET Sika Unitherm Platinum
PRODUCT DATA SHEET Solvent free, ultra high build, two pack, modified epoxy resin based, intumescent fire protection coating for internally or externally exposed structural steel. Ideal for in-shop application.
More informationOWL FORCE 10 (A+B+C) Epoxy-cement waterproofing (water barrier).
1618320 WATERPROOFING liquid Epoxycement waterproofing (water barrier). Three component epoxy resin to waterproof in negative and positive pressure, to use as osmotic on underground wall, to encapsulate
More informationPre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 1, suitable for exterior exposure in offshore environment, below 120 C.
Approved 402;2521 1,2 2521 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a very high zinc dust containing product. It conforms
More informationProperty Test/Standard Description
Approved 32222;32223;35142 1 32222 epoxy composite ^(ValidationDate) 1 Product description This is a two component glass flake reinforced epoxy composite coating. It is heat resistant up to 250 C (482
More informationROCKGRIP UNIVERSAL ACRYLIC PVA
TECHNICAL DATA SHEET Version 1 2016 FEBRUARY THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION Matt finish for interior use PRODUCT USES Suitable for use on primed new or previously painted
More informationApproved. Property Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method 1 32 C calculated VOC-US/Hong Kong. US EPA method 24 (tested)
Approved 30060;30061 1,2 30060 polyurethane ^(ValidationDate) 1 Product description This is a two component chemically curing aliphatic acrylic polyurethane coating. It has a glossy finish with very good
More informationPRODUCT DATA SHEET. Sika Pyroplast Wood T with Topcoat Sika Pyroplast Wood Top T PRODUCT DESCRIPTION
PRODUCT DATA SHEET Water based fire protective coating for wood, interior use PRODUCT DESCRIPTION USES PROPERTIES TESTS Sika Pyroplast Wood T is a water borne, transparent fire protection coating which
More informationtwo component polyamide cured epoxy primer yellow/green - eggshell
6 pages Revision of December 006 DESCRIPTION PRINCIPAL CHARACTERISTICS COLOURS AND GLOSS BASIC DATA AT 0 C Mass density Volume solids VOC (supplied) Recommended dry film thickness Theoretical spreading
More informationMagna Wall. Elastomeric Coatings (Non-Textured) Product Overview, Instructions, & Data
Magna Wall Elastomeric Coatings (Non-Textured) Product Overview, Instructions, & Data s t u c c o D 9 Magna Wall Elastomeric Coatings (Non-Textured) product Overview Magna Wall Elastomeric Coatings are
More informationProperty Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 35 C
Other Technical Data Sheet 13640;13641 1 13640 epoxy VValidationDate). 1 Product description This is a two component polyamine cured epoxy coating. It is an ultra high build, high solids abrasion resistant
More information0 PROCESS OF CRACKING 2
02 PROCESS OF CRACKING 02 PROCESS OF CRACKING The formation of cracks and their dynamic development are phenomena linked to various causes that create an interruption in the continuity of the substrate,
More informationApproved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (30 C) calculated VOC-US/Hong Kong
Approved 15360;15380 1,2 15360 epoxy ^(ValidationDate) 1 Product description This is a two component polyamine cured pure epoxy coating. It is a fast drying, abrasion resistant, high solids, high build
More informationE.MIX MOISTURE SEALER
E.MIX Super Fast Fix Fast setting, high performance, high strength, highly flexible, strong polymerized thin bed tile adhesive for interior and exterior wall tile fixing complied with C2FTE class of EN
More informationInstallation Instructions. Important. Recommended Tools. Palladium Rigid Sheet/Rubrail or Palladium G2 Sheet/Rubrail. Storage
Important Storage Flat sheet - Store Palladium Rigid Sheet in a clean, dry, interior area at temperatures between 50 F and 95 F [10-35 C]. Keep out of direct sunlight. Make sure sheet is well supported.
More information