BTM BT2K 600. Areas of Use
|
|
- Stewart Warner
- 6 years ago
- Views:
Transcription
1 BTM BT2K 600 Bitumento BT2K 600 is a solvent-free, two-component, elastic, water-based, fiber reinforced, rubber and cement based bitumen waterproofing material. Areas of Use As water and moisture tight material in underground applications such as foundation, base wall and basement, Protection and isolation of structures and structural elements which are exposed to seepage water and continuous or temporary water pressure, As water proofing material in dry or slightly moist details such as terrace, kitchen, bathroom, etc., Isolation of mineral surfaces such as concrete, stone, brick, briquette, plaster, grout, etc., Repair of old isolations such as bituminous membrane, asphalt, etc., Fastening of heat insulation boards, Isolation application with resistance to higher pressure water, together with isolation net, isolation fabric, etc. Advantages High elasticity and capability of bridging cracks.
2 Not affected by microorganisms and aggressive underground waters. Forms a flexible, covering and continuous asphalt layer on horizontal and vertical surfaces, dry and slightly moist surfaces. No damage to environment as it is water based. Easy to use indoors. No swelling and flaking by time due to very good adherence. Technical Specifications Basis: 2-component Polymer-bitumen based coating Liquid Component polymer bitumen dispersion Powder Component modified cement compound Color: Black Form: pasty,viscous liquid Density: appx 1,1 kg/lt Heat resistance: 100 o C Water Tightness after Curing (DIN 1048): 7 bar Application Application temperature: +5 o C / +35 o C Application surface temperature: +5 o C / +30 o C Working Time: 1-2 hours Drying time *: min. 48 hours Mixing ratio (by weight): liquid component : 3 powder component : 1 * Depending on temperature and relative humidity Surface Preparation The substrate should be free of dust, dirt, rust and oil, and loose parts scraped. The steel and wooden dowels should be removed from the surface. Wide cracks and gaps should be filled with Elastopast or Elastomast. The corners and edges should be rounded by at least 4 cm in
3 diameter. Bitümento BT2K 600 should be applied on dry concrete. Application Mixing : Mixing ratio : 3 parts by weight liquid component 1 parts by weight powder component The powder component should be added in the liquid component slowly, and mixed in a mixer with rpm for 3-5 minutes until a homogeneous mixture without lumps is obtained. The mixed material should be consumed up within 1-2 hours. Priming : Apply ready-mixed Bitumento BT2K 600, diluted with 1:5 with water, or the bitumen emulsion BTR200, diluted 1:2 with water or liquid component of BT2K 600 diluted 1:10 with water, to the substrate. The material should be applied on the surfaces by means of a brush without allowing accumulation of material. The primer should be allowed for drying, and then the main application should be done. Application of the coating: After the primer dried, it is applied in a thickness of 2-5 mm by means of brush, trowel or appropriate spray equipment. It may be applied in higher quantities depending on the absorption, porosity of the surface and the water pressure to which the waterproof layer will be exposed. In case of double-layer application, the first layer should be allowed for curing and then the second layer should be applied. It is recommended to use with gr/m² fiberglass or net to improve mechanical properties in large areas and horizontal? vertical joints and to bridge the cracks. The mixture prepared should be consumed up within 1-2 hours depending on the weather temperature. The application tools should be cleaned with water immediately after application. The tools which have not been cleaned timely, may be cleaned with thinner later. Consumption
4 -> Insulation against moisture: min. 3.3 kg/m2 for a thickness of 3 mm -> Against non-pressure water: min. 4.4 kg/m2 for a thickness of 4 mm -> Against pressurized water: min. 6.6 kg/m2 for a thickness of 6 mm -> min. 2 kg/m 2 for fastening Heat Insulation Board As primer; use of liquid component by adding 1:10 water kg/m 2 use of mixture by adding 1:5 water kg/m 2 NOTE: The consumption quantities may vary depending on the application details and surface smoothness, absorption. Packaging The liquid and powder components in 32 kg plastic bins (Liquid; 24 kg., Powder; 8 kg.) Storage Conditions and Shelf Life It should be stored in a dry location, and protected against sun and frost. The product freezes at temperatures below 0 o C. The shelf life is 12 months in unopened original packaging and under proper storage conditions. Considerations It should not be applied at temperatures below +5 C or in cases where the temperature is expected to drop below +5 C within 24 hours following application. The mixture should be prepared only with the liquid and powder components of the product. No foreign substance should be added. It should not be applied on wet and frozen surfaces. The application should not be made on surfaces at temperatures below +5 C?den or above +30 C.
5 The application should be protected against dew, frost, etc. until it fully dries. The coating should be applied on those surfaces of the structure and structural elements which are in contact with water. In foundation isolation applications, the waterproofing layer should be protected against mechanical damage by heat insulation boards, drain sheets or bricks before filling. The soil filling should be applied at least 3 days after waterproof application. Cautions and Recommendations The powder should not be inhaled as it is cement based. Gloves and protective goggles should be worn. In case of eye or skin contact, it should be washed with abundant amount of water and soap, and doctor should be consulted in case of eye contact. The empty packages should not be used for storage of drinking water or foodstuff. The tools should be cleaned with water after application. Responsibility The data contained in this technical document is based on scientific knowledge. BTM A.Ş is only responsible for the product quality. BTM A.Ş. may not be held responsible for other than recommendations on how and where to use the product and/or any improper use and consequences thereof.
COVERFLEX TWO-PART ELASTOPLASTIC CEMENT MORTAR FOR WATERPROOFING APPLICABLE WITH ROLL, BRUSH OR TROWEL. DESCRIPTION FIELDS OF APPLICATION
TWO-PART ELASTOPLASTIC CEMENT MORTAR FOR WATERPROOFING APPLICABLE WITH ROLL, BRUSH OR TROWEL. DESCRIPTION FIELDS OF APPLICATION COVERFLEX is a special two-part plastic cement mortar consisting of cementitious
More informationProduct Data Sheet. Description. Uses. Suitable Surfaces. Polymer enhanced, pre-blended, bag mix, coarse float render.
Product Data Sheet Render MaxiCoarse Polymer enhanced, pre-blended, bag mix, coarse float render. Description MaxiCoarse Render is a pre-blended, polymer fortified cement based render mix, formulated to
More information2 COMPONENT LIQUID WATERPROOFING PART 1 GENERAL. A. Two component liquid waterproofing for positive side waterproofing on mineral substrates
2 COMPONENT LIQUID WATERPROOFING PART 1 GENERAL 1.1 SECTION INCLUDES A. Two component liquid waterproofing for positive side waterproofing on mineral substrates 1.2 REFERENCES A. CE / EN1504-2 : 2005 Surface
More informationAQUATEK Impercem 10HB
AQUATEK Impercem 10HB Rigid waterproofing mortar Product Description AQUATEK Advantages Impercem 10HB is a rigid, cement based mortar for waterproofing of concrete and masonry. High adhesion and performance
More informationSIDER-POOL. Product Data. Features and Uses
153 Regur Road Hawkinsville, GA 31036 USA 1.478.892.9800 888-743-3750 sales@sider-crete.com www.sider-crete.com Product Data Features and Uses A true cement-based plaster No-check cracking and no-brushing
More informationSealing slurry system component of the KÖSTER KD System. approx. 15 min. approx. 20 sec. 2-3 hours. up to 7 bar (negative side)
Technical Data Sheet W 211 Issued: 2015-05-05 Sealing slurry system component of the Features The environmentally friendly stops active water ingress and safely seals off pressurized water from the negative
More information2013 Product Catalogue
2013 Product Catalogue We Change Chemistry Of The Structure. The quality of the materials used in building and construction areas are also increasing and as a result, lifting our standarts of living to
More informationLastogum X. Waterproof, flexible protective coating. Under ceramic coverings in showers and bathrooms
Waterproof, flexible protective coating Lastogum X Under ceramic coverings in showers and bathrooms With official test certificates. Fields of application Features and Benefits! Liquid area waterproofing
More informationMasterSeal M 861 (Formely known as Conipur M 860 Thix)
DESCRIPTION OF PRODUCT MasterSeal M 861 is a two component, solvent free, thixotropic, polyurethane based waterproofing membrane with crack bridging capability for vertical surfaces. Complies with EN 1504-2
More informationSealArm Tape TPE. Building & Joint Sealants T E C H N I C A L D A T A S H E E T. Uses. Features and Benefits
Product Description is a high performance Joint Tape system for expansion, it can be used for connection joints as well as for cracks, when fixed to the joint, allows irregular and high movement in more
More informationPU PRIMER 870 TRANSPARENT, ONE COMPONENT, POLYURETHANE-BASED PRIMER, USED AS AN ADHESIVE COMPONENT FOR SAFEPOL MULTICOLOR 859
PU PRIMER 870 EDITION: SEPTEMBER 2013 TRANSPARENT, ONE COMPONENT, POLYURETHANE-BASED PRIMER, USED AS AN ADHESIVE COMPONENT FOR SAFEPOL MULTICOLOR 859 GENERAL CHARACTERISTICS POLYURETHANE PRIMER 870 is
More informationTwo-component, highly flexible, cement-based waterproofing slurry
Technical Datasheet AQUAMAT-ELASTIC Two-component, highly flexible, cement-based waterproofing slurry Description AQUAMAT-ELASTIC is a two-component, highly flexible waterproofing slurry consisting of
More informationDESCRIPTION FEATURES AND BENEFITS AREAS OF USE. Showers & Bathrooms. Balconies & Patios SUITABLE SUBSTRATES. for application on: Concrete & Masonry
Product Information Technical Data Sheet - August 2017 High Performance DESCRIPTION Crommelin High Performance Under-tile Waterproof Membrane is an exceptionally flexible, 2 part cementitious, positive
More informationTurkQua products will give you complete satisfaction for your indoor and outdoor work with an exceptional quality. facebook/turkqua
Al Azizya Chemicals Factory is a Qatar based construction chemicals manufacturing company. We manufacture construction chemicals for all phases of construction from foundations to finishes under the International
More informationSupaflow HF Grout. Dual Expansion Class C Grout. Description. Areas of application. Features
Supaflow HF Grout Dual Expansion Class C Grout Description Supaflow HF is a free flowing cement based grout offering high performance and non-shrink characteristics. This product is suitable for pumping
More informationOMNITEK Deco is suitable for all leveling and thin layer concrete repair applications, such as:
OMNITEK Deco High strength leveling mortar, Class R4 Product Description OMNITEK Deco is a high strength, cement based, volume stable mortar, suitable for leveling and finishing of concrete surfaces in
More informationData Sheet Eco-Smart Membrane WS M1
Water-based Acrylic WS M1 Elastomeric Waterproofing Membrane is a durable, multi-use, extremely durable acrylic coating. At an ideal wet film thickness of 10-14 mils per coat (8-10 mils dry film finish
More informationData Sheet 3550 Englisch
Data Sheet 3550 Englisch ETICS Powder Adhesive 3550 WDVS Pulverkleber 3550 mineral adhesive and reinforcing plaster for Brillux ETICS Systems I through VI Properties Mineral adhesive and reinforcing powder.
More informationELASTOFLEX ELASTOMERIC TEXTURED ACRYLIC WALL COATING SPECIFICATION
ELASTOFLEX ELASTOMERIC TEXTURED ACRYLIC WALL COATING SPECIFICATION PART 1 - GENERAL 1.01 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions,
More informationEpoxy Based, Two Component, Grouting Filling and Ceramic Adhesive Resistant to Chemicals and Bacteria
MasterTile EPO 700 (Formerly known as Epofuga (Formerly known as Mastertile 700) ) 700 Epoxy Based, Two Component, Grouting Filling and Ceramic Adhesive Resistant to Chemicals and Bacteria Description
More informationFinish for topped and smooth surfaces, with or without chips. Pore and cavity filler, joint filler, adhesive for tiles etc.
Wecryl R 230 Accurate Details Complex details, penetrations or joints are the weak points of every Roof Waterproofing System. Upstands and edging on details can be waterproofed without seams or joints
More informationConstruction. One component cementitious mortar fibre reinforced for flexible waterproofing. Product Description. Product Data. Form.
Product Data Sheet Edition 12/12/2014 Identification no: 02 07 01 01 001 0 000180 Sikalastic -1K Sikalastic -1K One component cementitious mortar fibre reinforced for flexible waterproofing Construction
More informationDue to increased resistance to chemicals it can also be used for the protection of (1): gathering shafts and fuel pools, concrete silos, Etc.
Tehnični list proizvoda, izdaja 6/2017 - ANG EN 1504-2: covering/coating PROPERTIES Hidroizol S is a dry mixture of cement, flint sands and special admixtures to increase water impermeability, resistance
More informationMONOBASE AAC/ SIDER-PLAST THE ULTIMATE EXTERIOR HARD COAT STUCCO SYSTEM FOR AUTOCLAVED AERATED CONCRETE
SIDER-CRETE, INC. 153 Regur Road Hawkinsville, GA 31036 USA Ph: 478.892.9800 www.sider-crete.com MONOBASE AAC/ SIDER-PLAST THE ULTIMATE EXTERIOR HARD COAT STUCCO SYSTEM FOR AUTOCLAVED AERATED CONCRETE
More informationHomogenous cement-based powder, modified with high quality polymers and cellulose additives.
Page: 1 от 5 (winter formula) adhesive mortar solution for bonding thermo insulation EPS/XPS boards on different bases when thermo-insulating buildings, in mild winter conditions (temperatures from 0 C
More informationSelf Adhesive EPDM TRAINING MANUAL
Self Adhesive EPDM TRAINING MANUAL Rubber4Roofs Ltd, Unit 4 Kingswood Close Page 1 of 7 Copyright Rubber4Roofs Ltd GeneralHealth&Safety Extreme care must be exercised when working on ladders, roofs, below
More informationPRODUCT DATA SHEET Sikadur 31 CF Normal (formerly Sikadur 731)
PRODUCT DATA SHEET (formerly Sikadur 731) 2-part Thixotropic Epoxy Adhesive PRODUCT DESCRIPTION Sikadur-31 CF Normal is a solvent-free, moisture tolerant, thixotropic, structural two part adhesive and
More informationPEKAY T570 RUBBERSEAL
PEKAY T570 RUBBERSEAL DESCRIPTION Pekay Rubberseal T570 is a rubber-latex modified anionic bitumen emulsion, which dries to a pliable, flexible, waterproof, black coating. It may be used for a variety
More informationPolymer bonding aid and mortar additive bonding agent for old and new concrete. Test method Typical result Control. Compressive strength (BS6319,Pt2)
Techno Bond SBR Polymer bonding aid and mortar additive bonding agent for old and new concrete Uses For improving the physical properties of cementations mixes. Typical uses include, but are not limited
More informationCool-R is one component, highly reflective, seamless, waterproofing coating for new and refurbished roofs. It can be use on flat and slope roofs.
Cool-R TECHNICAL DOCUMENT 7/2016/EN Cool-R is one component, highly reflective, seamless, waterproofing coating for new and refurbished roofs. It can be use on flat and slope roofs. TYPICAL APPLICATION
More informationRD COATINGS -RD-ELASTOFLEX ELASTOMERIC ACRYLIC WALL COATING SPECIFICATION
RD COATINGS -RD-ELASTOFLEX ELASTOMERIC ACRYLIC WALL COATING SPECIFICATION PART 1 - GENERAL 1.01 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions,
More informationISO COMPANY K POLYSEAL G TWO PART GUN GRADE POLYSULPHIDE SEALANT
ISO 9001-2000 COMPANY K POLYSEAL G TWO PART GUN GRADE POLYSULPHIDE SEALANT DESCRIPTION KPOLYSEAL is a two part gun grade joint sealant based on a liquid polysulphide when mixed together, cure to form a
More informationElastic 2C is a flexible, crack bridging, cement based 2-component coating for waterproofing and ingress protection of concrete and masonry.
AQUATEK Elastic 2C Flexible cement based waterproofing coating Product Description AQUATEK Elastic 2C is a flexible, crack bridging, cement based 2-component coating for waterproofing and ingress protection
More informationHigh performance, flexible cementitious tile adhesive for thin bed application
Product Data Sheet Edition 05.11.2008 Revision no.: 1 Identification no: 01 07 01 01 001 0 000071 Sika Ceram-205 T (Sika Ceram 201) High performance, flexible cementitious tile adhesive for thin bed application
More informationTECHNICAL DATA SHEET SIKALASTIC-1K
TECHNICAL DATA SHEET SIKALASTIC-1K Sikalastic -1K is a one component, highly elastic, cementitious fibre-reinforced mortar for the flexible waterproofing of concrete structures. It can be used for the
More informationPOWERBASE ICF / SIDER PROOF FF-PR
153 Regur Road Hawkinsville, GA 31036 USA 1.478.892.9800 888-743-3750 www.sider-crete.com Designer & Manufacturer of the original Roll-On Pool Plaster! POWERBASE ICF / SIDER PROOF FF-PR Product Data Features
More informationPRODUCT DATA SHEET Sikalastic -501 Roofseal Plus
PRODUCT DATA SHEET ECONOMICAL LIQUID APPLIED ROOF WATERPROOFING SOLUTION DESCRIPTION is a cold-applied, onecomponent waterborne liquid applied waterproofing membrane, highly elastic and UV resistant. USES
More information"WE CAN AGUASEAL THAT" AGUASEAL WATERPROOFING SYSTEMS A G U A B A S E
"WE CAN AGUASEAL THAT" AGUASEAL WATERPROOFING SYSTEMS A G U A B A S E A G U A B A S E WHAT IS AGUABASE? AguaBase is utilized worldwide as a waterproofing system for below grade foundation walls, steel
More informationSECTION MAINTENANCE OF STONE ASSEMBLIES
SECTION 04 01 40 - MAINTENANCE OF STONE ASSEMBLIES PART 1 GENERAL 1.1 SUMMARY OF WORK A. Submit the following items in time to prevent delay of the work and to allow adequate time for review, do not order
More informationCopolymer BEFORE. Copolymer DURING. Copolymer AFTER. (800) TRI-CHEM 3
Roof Repair Copolymer BEFORE Copolymer DURING Copolymer AFTER www.tri-chem.com (800) 456-6255 TRI-CHEM 3 TECHNICAL DATA SHEET TRI-MEMBRANE DESCRIPTION Tri-Membrane is an asphalt impregnated cotton membrane
More informationFiber Reinforced Tile and Stone Mortar
, ANSI A 118.4, ANSI A 118.11 ARDEX X 77 MICROTEC Fiber Reinforced Tile and Stone Mortar The most advanced technology ideal for large format porcelain tile installations,exterior or interior, floor or
More informationDELTA -THENE laying instructions
DELTA protects property. Saves energy. Creates comfort. DELTA -THENE laying instructions P R E M I U M Q U A L I T Y Waterproofing system for horizontal and vertical applications. Laying instructions for
More informationMagna Wall. Elastomeric Coatings (Non-Textured) Product Overview, Instructions, & Data
Magna Wall Elastomeric Coatings (Non-Textured) Product Overview, Instructions, & Data s t u c c o D 9 Magna Wall Elastomeric Coatings (Non-Textured) product Overview Magna Wall Elastomeric Coatings are
More informationASPHALT CEMENTS & COATINGS. Roof Mastics Protective Asphalt Coatings Asphalt Primers Aluminum Coatings
ASPHALT CEMENTS & COATINGS Roof Mastics Protective Asphalt Coatings Asphalt Primers Aluminum Coatings ROOF MASTICS #211 PLASTIC CEMENT Mule-Hide #211 Plastic Cement is a general purpose formulation for
More informationSika-Trocal C200 Adhesive. Sika-Trocal C200 is an adhesive to bond certain insulation boards on approved substrates.
Sika-Trocal C200 Adhesive Adhesive for Insulation Boards Product Description Polyurethane-based humidity-curing one-part adhesive. Uses Sika-Trocal C200 is an adhesive to bond certain insulation boards
More informationConforms to the requirements of ETAG Certificate: European Technical Approval No. ETA-05/0265
PRODUCT DATA SHEET UV-resistant, highly elastic polyurethane waterproofing seal coat PRODUCT DESCRIPTION is a one part, solvent containing, highly elastic, moisture curing polyurethane seal coats. USES
More informationE.MIX MOISTURE SEALER
E.MIX Super Fast Fix Fast setting, high performance, high strength, highly flexible, strong polymerized thin bed tile adhesive for interior and exterior wall tile fixing complied with C2FTE class of EN
More informationMasterSeal M 616. THEORETICAL CONSUMPTION kg/m 2. PACKAGES 25 kg and 5 kg cans
DEFINITION OF THE MATERIAL is a UV resistant, water-based hybrid polyurethane single-component elastic waterproofing product. is in fact classified as waterproofing agent UNI EN 14891 type CM-O1-P (for
More informationCUSTOM BRICK. Custom Brick Finish Polymer System Specifications For Use On Vertical Walls DS151. Architectural Finish for Use on Vertical Walls
CUSTOM BRICK Architectural Finish for Use on Vertical Walls Custom Brick Finish Polymer System Specifications For Use On Vertical Walls PART I- GENERAL DRYVIT SYSTEMS, INC. MANUFACTURER S SPECIFICATION
More informationCrystoflex Max comprising of a liquid component of selected polymers and a powder component of selected cements, fillers and aggregates.
Product Data Sheet Crystoflex Max Two pack, flexible, cementitious waterproofing membrane for positive or negative water pressure. Description Crystoflex Max is a two pack, flexible, cementitious waterproof
More informationRAPIDFOAM PAD 868 PREFABRICATED SHOCK-PAD FOR PLAYGROUND FLOORING
RAPIDFOAM PAD 868 EDITION: SEPTEMBER 2017 PREFABRICATED SHOCK-PAD FOR PLAYGROUND FLOORING GENERAL CHARACTERISTICS RAPIDFOAM PAD 868 is the prefabricated cushion sub-base of the playground flooring QUICKLAWN
More informationTechnical Information
This technical sales bulletin is concerned with the variety of applications and methods available using Resinflow s GPS plus it also includes the GP primer and Screed Block data sheets. Primer Latex/Cement
More informationCUSTOM BRICK. Custom Brick Finish Polymer System Specifications For Use On Vertical Walls DS151. Architectural Finish for Use on Vertical Walls
CUSTOM BRICK Architectural Finish for Use on Vertical Walls Custom Brick Finish Polymer System Specifications For Use On Vertical Walls PART I- GENERAL DRYVIT SYSTEMS, INC. MANUFACTURER S SPECIFICATION
More informationOWL FORCE 10 (A+B+C) Epoxy-cement waterproofing (water barrier).
1618320 WATERPROOFING liquid Epoxycement waterproofing (water barrier). Three component epoxy resin to waterproof in negative and positive pressure, to use as osmotic on underground wall, to encapsulate
More information3-component epoxy self-smoothing screed
Construction Product Data Sheet Edition 26/07/2016 Identification no: 01 08 01 02 050 0 000017 3-component epoxy self-smoothing screed Product Description Uses Characteristics / Advantages Product Data
More informationAQUAMAT. Cement-based, brushable waterproofing slurry. Technical Datasheet
Technical Datasheet AQUAMAT Cement-based, brushable waterproofing slurry Description AQUAMAT is a cement-based, brushable waterproofing slurry offering: Total waterproofing against positive hydrostatic
More informationZinc Silicate (Inorganic)
Product code: 477-041: part A 477-042: part B General description: Two-component, zinc-ethyl silicate-. Forms a continuous coat of metallic zinc that provides cathodic protection to metal (as in hot galvanization).
More informationK5 AQUAPLUG A FAST SETTING PLUGGING COMPOUD FOR STOPPAGE OF RUNNING WATER
ISO 9001-2000 COMPANY K5 AQUAPLUG A FAST SETTING PLUGGING COMPOUD FOR STOPPAGE OF RUNNING WATER DESCRIPTION K5 AQUAPLUG is a fast setting hydraulic compound which stops running water instantly. K5 AQUAPLUG
More informationGeneral Applications Before applying, mix the pre-measured catalyst* into Liquid Roof by following label directions.
General Applications Before applying, mix the pre-measured catalyst* into Liquid Roof by following label directions. Surface Preparation: Surface to be coated should be clean, dry and structurally sound.
More informationRITIVEX R LIQUID 1102
RITIVEX R LIQUID 1102 EDITION: SEPTEMBER 2013 ADHESIVE, ACRYLIC RESIN FOR MULTIPLE USES GENERAL CHARACTERISTICS Acrylic, adhesive, joining resin, water - diluted. It is combined with all cementitious mortars
More informationAQUAMAT. Cement-based, brushable waterproofing slurry. Technical Datasheet
Technical Datasheet AQUAMAT Cement-based, brushable waterproofing slurry Description AQUAMAT is a cement-based, brushable waterproofing slurry offering: Total waterproofing against positive hydrostatic
More informationMasterEmaco S Lightweight, polymer modified, fibre reinforced, structural repair mortar. Formerly: Emaco Nanocrete R3 DESCRIPTION
DESCRIPTION MasterEmaco S 5300 is a single component, lightweight, polymer modified, high build structural repair mortar that meets the requirements of the new European Norm EN 1504 part 3 class R3. MasterEmaco
More information1-part elastic joint sealant and multipurpose adhesive
Product Data Sheet Edition 15/11/2005 Identification no: 02 05 01 01 005 0 000001 1-part elastic joint sealant and multipurpose adhesive Construction Product Description Uses Characteristics / Advantages
More informationRITIVEX R LIQUID 1102
RITIVEX R LIQUID 1102 EDITION: SEPTEMBER 2013 ADHESIVE, ACRYLIC RESIN FOR MULTIPLE USES GENERAL CHARACTERISTICS Acrylic, adhesive, joining resin, water - diluted. It is combined with all cementitious mortars
More informationWATERPROOFING OF AN ACCESSIBLE FLAT ROOF WITH A POLYURETHANE LIQUID MEMBRANE AND TILING
WATERPROOFING OF AN ACCESSIBLE FLAT ROOF WITH A POLYURETHANE LIQUID MEMBRANE AND TILING WATERPROOFING OF AN ACCESSIBLE FLAT ROOF WITH A POLYURETHANE LIQUID MEMBRANE AND TILING 4 5 6 7 3 2 1 1. CONCRETE
More informationEN 14891:2012/AC:2012
Construction Product Data Sheet Edition 24/07/2014 Code: 03.02.070 Identification no: 010701010020000043 EN 1504-2:2004 EN 14891:2012/AC:2012 13 0546 01599 Rapid curing cement mortar for flexible waterproofing
More informationAquaflex. Roof Plus. Ready-to-use, high-elasticity, quick-drying, UV-resistant liquid waterproofing membrane PI-MC-IR
IN COMPLIANCE WITH EUROPEAN STANDARD EN 1504-2 (C) PRINCIPLES PI-MC-IR SURFACE PROTECTION SYSTEMS FOR CONCRETE Aquaflex EN 1504-2 Ready-to-use, high-elasticity, quick-drying, UV-resistant liquid waterproofing
More informationPRODUCT DATA SHEET Sika Level-315 F
PRODUCT DATA SHEET CEMENTITIOUS SELF LEVELLING, FAST DRYING, FIBRE REINFORCED UNDERLAYMENT FOR USE 3-15MM THICK ON INTERIOR FLOORS PRODUCT DESCRIPTION Sika Level-315 F is a one part, polymer modified,
More informationData Sheet 832 Englisch
Englisch Primer LF 832 Floortec 2K-Epoxi-Grund LF 832 solvent-free, transparent primer resin as primer in Floortec PUR Coating System and under Floortec 2C Epoxy Thick Layer LF 834 Properties Solvent-free,
More informationRITIVEX R LIQUID 1102
RITIVEX R LIQUID 1102 EDITION: SEPTEMBER 2013 ADHESIVE, ACRYLIC RESIN FOR MULTIPLE USES GENERAL CHARACTERISTICS Acrylic, adhesive, joining resin, water - diluted. It is combined with all cementitious mortars
More informationPurtop System Roof SPRAY-APPLIED HYBRID POLYUREA WATERPROOFING SYSTEM FOR NON-TRAFFICKED ROOFS
Purtop System Roof SPRAY-APPLIED HYBRID POLYUREA WATERPROOFING SYSTEM FOR NON-TRAFFICKED ROOFS PRODUCTS USED FOR THE SYSTEM: Purtop 600 - Purtop 400 M - Purtop 1000 - Primer SN - Triblock P - Mapecoat
More informationunique WATERPROOFING PRODUCTS Creating distinctive cement finishes as you are. Products for waterproofing, treatment of damp & pond lining
WATERPROOFING PRODUCTS Products for waterproofing, treatment of damp & pond lining unique Creating distinctive cement finishes as as you are. R Manufacturers of Distinctive Decorative Coatings MATCRETE
More informationSMOOTH SURFACED BUILT-UP ROOFS WITH ARC SEBS REFLECTIVE ROOF COATINGS
1.0 SCOPE SPECIFICATION FOR COATING SMOOTH SURFACED BUILT-UP ROOFS WITH ARC SEBS REFLECTIVE ROOF COATINGS The intention of this specification is to outline the procedures for the application of ARC SEBS
More informationSetting holding down bolts Floor screeds Bedding blocks Stone and bricks In contact with potable water Fine moulding.
PRODUCT SHEET NATCEM 35 Description NATCEM 35 is a fast setting and fast curing mortar with a rapid strength gain that is resistant to chloride penetration, consisting of a blend of NATCEM Potable Water
More informationTECHNICAL DATA SHEET SIKADUR 31 CF NORMAL 6KG
TECHNICAL DATA SHEET SIKADUR 31 CF NORMAL 6KG Sikadur 31 is a two component solvent-free, cold cure, thixotropic epoxy adhesive suitable for damp and dry substrates. Available in two grades - Normal and
More informationMETHOD STATEMENT SIKALASTIC -680 AP SIKA LIMITED (VIETNAM)
METHOD STATEMENT SIKALASTIC -680 AP SIKA LIMITED (VIETNAM) 1 SCOPE This method statement describes the step by step application of 1-component component, liquid applied, highly elastic polyurethane waterproofing
More informationEUROPLAST. Color 20 standard colors, see color chart for specifics. Special colors available upon request, virtually no limit to selection of shades.
EUROPLAST By Stuc-O-Flex International, Inc. Description Europlast is a pre-colored, wet-mix polymer based interior & exterior coating system that transforms vertical walls into a classic example of old
More informationTECHNICAL DATA SHEET AUS-FLEX MULTI
FLEXIBLE TILE & STONE ADHESIVE POLYMER & RUBBER REINFORCED INTERNAL & EXTERNAL USE SUITABLE FOR: PORCELAIN TILE ALL MASONRY SURFACES CERAMIC TILE CONCRETE QUARRY TILE RENDER, BRICK & BLOCK WORK MOSAIC
More informationMEMBRANE WATER PROOFING. Our Services: Below ground waterproofing, Above-ground waterproofing, Wet Areas Waterproofing, Joint Sealants.
WATER PROOFING MEMBRANE s vast experience in providing constructive solutions to many famous building structures around the world hasbeen built on a broad portfolio of products. Our Services: Below ground
More informationROOF SUBSTRATE PREP MANUAL
ROOF SUBSTRATE PREP MANUAL ALDOCOAT Liquid Applied Roof Restoration Systems AFTER BEFORE JULY 2016 1604 N. Main St. Kannapolis, NC 28081 (800) 474-6019 www.aldoproducts.com ROOF SUBSTRATE PREPARATION Preparation
More informationMasterEmaco N Universal, fast setting, polymer modified, fibre reinforced, repair and levelling mortar DESCRIPTION FIELD OF APPLICATION
DESCRIPTION is a universal, single component, polymer modified, fast setting, repair, reprofiling and levelling mortar that meets the requirements of the new European Norm EN 1504 part 3 class R2. is a
More informationDMS WATERPROOFING
DMS - 6300 EFFECTIVE DATE: MAY 2009 6300.1. Description. This Specification governs the sampling, testing, composition, and quality of the following waterproofing materials: Butyl rubber membrane Ethylene-propylene-diene-terpolymer
More informationDMS EP-D80 Broadcasted Epoxy Resin Floor
Product description DMS EP-D80 system is a three component epoxy system, designed as epoxy binder containing special fire retardant additives and mineral fillers, such as quartz or granulated granite.
More informationTECHSEAL RDL 940/941
DESCRIPTION TECHSEAL RDL 940/941 are two component sealant based on THIOKOL Polysulphide liquid elastomer. It consists of a base compound and accelerator (Curing Agent). When the two components are mixed
More informationPOLAPLAST P10 POLYURETHANE PRIMER ONE-COMPONENT EDITION: SEPTEMBER 2013
EDITION: SEPTEMBER 2013 POLAPLAST P10 POLYURETHANE PRIMER ONE-COMPONENT GENERAL POLAPLAST P10 is a low viscosity, moisture curing, clear, polyurethane-based, one-component resin with good long term elasticity.
More informationShower Waterproofing Membrane Under tile and wet area waterproofing membrane.
Product Information Technical Data Sheet - December 2017 Shower Waterproofing Membrane Under tile and wet area waterproofing membrane. DESCRIPTION Crommelin Shower Waterproofing Membrane is a waterbased,
More informationAcrylic/Urethane. Metal Roof Restoration Sample Design Guideline
1 DG0009-I 04/2017 Metal Roof Restoration Sample Design Guideline Acrylic/Urethane ITW POLYMERS SEALANTS NORTH AMERICA, INC. 111 S. Nursery Road. Irving, TX 75060 Tel: 972-438-9111 Fax: 972-554-3939 www.itwsealants.com
More informationSTONEWRAP MANUFACTURED STONE VENEER - LUXURY MANUFACTURED STONE
STONEWRAP MANUFACTURED STONE VENEER - LUXURY MANUFACTURED STONE Stonewrap manufactured stone is produced by replicating natural stone. They are lighter in weight in comparison to natural stone. Due to
More informationPROBERT S TIP: Technical terms from A to Z. DIY Lexicon. Nur im
PROBERT S TIP: Technical terms from A to Z DIY Lexicon Nur im A Accumulating water Groundwater, accumulating water or stratum water that applies hydrostatic pressure to the wall. This type of loading must
More informationMaster-Seal Surface-Applied Waterproofing System
P 1/7 INDUSTRIAL ROOFING, INC. Master-Seal Surface-Applied Waterproofing System Master-Seal is a highly effective waterproofing system designed to seal surfaces from water seepage in roofs with minimum
More informationabe co mastic a.b.e. Construction Chemicals HEAVY DUTY MASTIC FLOORING SYSTEM DESCRIPTION PREPARATION OF SUB-FLOOR USES SURFACE PRIMING ADVANTAGES
a.b.e. Construction Chemicals abe co mastic HEAVY DUTY MASTIC FLOORING SYSTEM DESCRIPTION abe. co mastic is a cold-laid bituminous mastic consisting of stone chippings, Portland Cement, sand and a binder,
More informationWaterproofing and Damp-proofing Cementitious Slurry
Product Data Sheet Edition: 01/10/2012 Identification no. Version no: GCC SikaTop Seal-107 SikaTop Seal-107 Waterproofing and Damp-proofing Cementitious Slurry Product Description Uses SikaTop Seal-107
More informationPOWERBASE / SIDER-PROOF FF-PR
153 Regur Road Hawkinsville, GA 31036 USA 1.478.892.9800 888-743-3750 www.sider-crete.com Designer & Manufacturer of the original Roll-On Pool Plaster! Product Data POWERBASE / SIDER-PROOF FF-PR Features
More informationWestbuild PRO. Rapid Drying Wet Area Waterproofing. Polyurethane (PU) modified, permanently flexible, rapid drying, class III waterproof membrane.
Westbuild PRO Rapid Drying Wet Area Waterproofing Polyurethane (PU) modified, permanently flexible, rapid drying, class III waterproof membrane. Westbuild PRO Wet Area Waterproofing is highly flexible
More informationCP-24CC Potassium Silicate Concrete
CP-24CC Potassium Silicate Concrete PRODUCT DESCRIPTION Blome CP-24CC is a two component, potassium silicate concrete used for acid resistant pump pads, equipment pads, curbing, floors and sumps. CP-24CC
More informationDULUX WEATHERGUARD FINE TEXTURED
TECHNICAL DATA SHEET Version 1 2016 JULY THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION A tough, durable exterior coating with Maxiflex that provides lasting elasticity to cover hairline
More informationREV: DeckProof Flooring System Concrete Specification. Concrete Specification
REV:28.01.13 Please note all DeckProof materials cure within 20 minutes so only mix material for an area that can be covered within this time. Please consult the mixing section of this specification before
More informationSikaCor 255 Epoxy-binder for mortars on concrete and steel. Protective Coatings
Product Data-Sheet Edition 03.09 DS-Code: E 1605 SikaCor 255 Epoxy-binder for mortars on concrete and steel SikaCor 277 Thixotropic epoxy-binder - sag resistant high-build coatings and mortars Protective
More information