Signature Sports Flooring (Economy I Series Wall Padding) WPE1-XX Safety Wall Padding
|
|
- Franklin Montgomery
- 6 years ago
- Views:
Transcription
1 Signature Sports Flooring (Economy I Series Wall Padding) WPE1-XX Safety Wall Padding A. Basis-of-Design Product: Subject to compliance with requirements. Provide Signature Sports Flooring model WPE1-X X. B. Padded wall wainscot panels designed to be attached in a continuous row; each panel consist of foam filler laminated to OSB wood backing and covered with Class A Flame retardant vinyl coated polyester on full surface, sides, ends, and including all wood edges, vinyl is securely stapled to the back of the OSB backer board. 1. Backer Board: Not less than 7/16-inch- (11-mm-) SFI Certified Responsible Urea Formaldehyde Free recycled composite wood backer board. This portion of the product contributes toward satisfying Credit IEQ 4.4 under LEED 2. Foam Filler: Not less than 2-inch- (50.8-mm-) thick upholstery grade polyurethane foam filler, with a density of 3-lb/ ft3 (48-kg/ m3) x 70 IFD, meeting CAL. TB 117 flame retardant specification 3. Vinyl Covering: 16 -oz. / yd2 (543-g/ m3) Vinyl Coated Polyester - puncture and tear-resistant. CPSC CPSIA - 6P and lead compliant. Phthalates less than.1% and Lead less than 100 ppm. Achieving NFPA- 701 CSFM, and a Class A fire rating under ASTM E-84, with a smoke UV and Anti-Mildew treated. C. Sizing: Standard size panels are 24 inches (60.9 cm) wide x inches high (specify panel height) panel section or as indicated on Drawings. D. Color(s) of vinyl to be selected from manufactures standard color packet E. Corner and Column Pads: Pre-Fabricated / Field Fabricated corner and column pads to be built with materials consistent with standard padding specifications as listed above. F. Installation: Select one of three primary options below. Comply with manufacturers written instructions, Refer to Architects elevation drawings for panel placement. Mount panels no more than 4 above finished floor as recommended in in ASTM, unless otherwise directed. Install wall padding after painting and electrical have been completed use proper wall anchor hardware. 1. Panels to be supplied with a 1-inch- nail margin top and bottom and mounted directly to wall surface.
2 2. Panels to be supplied with a no nail margins and to be hung on concealed Aluminum Z track supplied by the wall pad manufacturer. 3. Panels to be supplied with a no nail margins and to be mounted to concealed 1-inch- x 3-inch- fir stripping that is attached in 3 continuous horizontal rows to the wall. Panels are affixed to the stripping using a toenail method of nailing. G. Adjusting: 1. Final adjustment of panels to insure a smooth finished appearance 2. Clean and remove any debris from the working area 3. Spot clean panels as may be necessary
3 Signature Sports Flooring (Economy II Series Wall Padding) WPE2-XX Safety Wall Padding A. Basis-of-Design Product: Subject to compliance with requirements. Provide Signature Sports Flooring model WPE2-XX. B. Padded wall wainscot panels designed to be attached in a continuous row; each panel consist of foam filler laminated to OSB wood backing and covered with Class A Flame retardant vinyl coated polyester on full surface, sides, ends, and including all wood edges, vinyl is securely stapled to the back of the OSB backer board. 1. Backer Board: Not less than 7/16-inch- (11-mm-) SFI Certified Responsible Urea Formaldehyde Free recycled composite wood backer board. This portion of the product contributes toward satisfying Credit IEQ 4.4 under LEED 2. Foam Filler: Not less than 2-inch- (50.8-mm-) thick hypoallergenic bonded urethane foam filler with a density of 6-lb/ ft3 (96-kg/ m3). Meets the ASTM standard Impact attenuation where the panel has achieved ratings below 1000 HIC and 200 g max. 100% pre-consumer recycled and 100% post-consumer recyclable. This portion of the product contributes toward satisfying Credit MR 4 under LEED 3. Vinyl Covering: 16 -oz. / yd2 (543-g/ m3) Vinyl Coated Polyester - puncture and tear-resistant. CPSC CPSIA - 6P and lead compliant. Phthalates less than.1% and Lead less than 100 ppm. Achieving NFPA- 701 CSFM, and a Class A fire rating under ASTM E-84, with a smoke UV and Anti-Mildew treated. C. Sizing: Standard size panels are 24 inches (60.9 cm) wide x inches high (specify panel height) panel section or as indicated on Drawings. D. Color(s) of vinyl to be selected from manufactures standard color packet E. Composite Testing: Manufacturer must warrant that a composite panel built with similar materials was tested and passes for ASTM standard Impact attenuation where the panel has achieved ratings below 1000 HIC and 200 g max. Manufacturer must also warrant that foam filler is hypoallergenic, produced using 100% recycled urethane, and is 100% post-consumer recyclable. F. Corner and Column Pads: Pre-Fabricated / Field Fabricated corner and column pads to be built with materials consistent with standard padding specifications as listed above.
4 G. Installation: Select one of three primary options below. Comply with manufacturers written instructions, Refer to Architects elevation drawings for panel placement. Mount panels no more than 4 above finished floor as recommended in in ASTM, unless otherwise directed. Install wall padding after painting and electrical have been completed use proper wall anchor hardware. 1. Panels to be supplied with a 1-inch- nail margin top and bottom and mounted directly to wall surface. 2. Panels to be supplied with a no nail margins and to be hung on concealed Aluminum Z track supplied by the wall pad manufacturer. 3. Panels to be supplied with a no nail margins and to be mounted to concealed 1-inch- x 3-inch- fir stripping that is attached in 3 continuous horizontal rows to the wall. Panels are affixed to the stripping using a toenail method of nailing. H. Adjusting: 1. Final adjustment of panels to insure a smooth finished appearance 2. Clean and remove any debris from the working area 3. Spot clean panels as may be necessary
5 Signature Sports Flooring (Premium I Series Wall Padding) WPP1-XX Safety Wall Padding A. Basis-of-Design Product: Subject to compliance with requirements. Provide Signature Sports Flooring model WPP1-X X. B. Padded wall wainscot panels designed to be attached in a continuous row; each panel consist of foam filler laminated to OSB wood backing and covered with Class A Flame retardant vinyl coated polyester on full surface, sides, ends, and including all wood edges, vinyl is securely stapled to the back of the OSB backer board. 1. Backer Board: Not less than 7/16-inch- (11-mm-) SFI Certified Responsible Urea Formaldehyde Free recycled composite wood backer board. This portion of the product contributes toward satisfying Credit IEQ 4.4 under LEED 2. Foam Filler: Not less than 2-inch- (50.8-mm-) thick, Low Smoke Polychloroprene compound foam filler with a density of 6-lb/ ft3. (96-kg/ m3). Achieves Class A fire rating under ASTM E-84, with a smoke 3. Vinyl Covering: 16 -oz. / yd2 (543-g/ m3) Vinyl Coated Polyester - puncture and tear-resistant. CPSC CPSIA - 6P and lead compliant. Phthalates less than.1% and Lead less than 100 ppm. Achieving NFPA- 701 CSFM, and a Class A fire rating under ASTM E-84, with a smoke UV and Anti-Mildew treated. C. Sizing: Standard size panels are 24 inches (60.9 cm) wide x inches high (specify panel height) panel section or as indicated on Drawings. D. Color(s) of vinyl to be selected from manufactures standard color packet E. Composite Testing: Manufacturer must warrant that a composite panel built with similar materials was tested and achieves an overall Class A fire rating under ASTM Standard E-84, with a smoke developed index of 450 or less and a flame spread index of 25 or less. F. Corner and Column Pads: Pre-Fabricated / Field Fabricated corner and column pads to be built with materials consistent with standard padding specifications as listed above. G. Installation: Select one of three primary options below. Comply with manufacturers written instructions, Refer to Architects elevation drawings for
6 panel placement. Mount panels no more than 4 above finished floor as recommended in in ASTM, unless otherwise directed. Install wall padding after painting and electrical have been completed use proper wall anchor hardware. 1. Panels to be supplied with a 1-inch- nail margin top and bottom and mounted directly to wall surface. 2. Panels to be supplied with a no nail margins and to be hung on concealed Aluminum Z track supplied by the wall pad manufacturer. 3. Panels to be supplied with a no nail margins and to be mounted to concealed 1-inch- x 3-inch- fir stripping that is attached in 3 continuous horizontal rows to the wall. Panels are affixed to the stripping using a toenail method of nailing. H. Adjusting: 1. Final adjustment of panels to insure a smooth finished appearance 2. Clean and remove any debris from the working area 3. Spot clean panels as may be necessary
7 Signature Sports Flooring (Premium II Series Wall Padding) WPP2-XX Safety Wall Padding A. Basis-of-Design Product: Subject to compliance with requirements. Provide Signature Sports Flooring model WPP2-X X. B. Padded wall wainscot panels designed to be attached in a continuous row; each panel consist of foam filler laminated to OSB wood backing and covered with Class A Flame retardant vinyl coated polyester on full surface, sides, ends, and including all wood edges, vinyl is securely stapled to the back of the OSB backer board. 1. Backer Board: Not less than 7/16-inch- (11-mm-) SFI Certified Responsible Urea Formaldehyde Free recycled composite wood backer board. This portion of the product contributes toward satisfying Credit IEQ 4.4 under LEED 2. Foam Filler: Not less than 2-inch- (50.8-mm-) thick, Low Smoke Polychloroprene compound foam filler with a density of 6-lb/ ft3. (96-kg/ m3). Achieves Class A fire rating under ASTM E-84, with a smoke 3. Vinyl Covering: 16 -oz. / yd2 (543-g/ m3) Vinyl Coated Polyester - puncture and tear-resistant. CPSC CPSIA - 6P and lead compliant. Phthalates less than.1% and Lead less than 100 ppm. Achieving NFPA- 701 CSFM, and a Class A fire rating under ASTM E-84, with a smoke UV and Anti-Mildew treated. C. Sizing: Standard size panels are 24 inches (60.9 cm) wide x inches high (specify panel height) panel section or as indicated on Drawings. D. Color(s) of vinyl to be selected from manufactures standard color packet E. Composite Testing: Manufacturer must warrant that a composite panel built with similar materials was tested and achieves an overall Class A fire rating under ASTM Standard E-84, with a smoke developed index of 450 or less and a flame spread index of 25 or less. F. Corner and Column Pads: Pre-Fabricated / Field Fabricated corner and column pads to be built with materials consistent with standard padding specifications as listed above. G. Installation: Select one of three primary options below. Comply with manufacturers written instructions, Refer to Architects elevation drawings for
8 panel placement. Mount panels no more than 4 above finished floor as recommended in in ASTM, unless otherwise directed. Install wall padding after painting and electrical have been completed use proper wall anchor hardware. 1. Panels to be supplied with a 1-inch- nail margin top and bottom and mounted directly to wall surface. 2. Panels to be supplied with a no nail margins and to be hung on concealed Aluminum Z track supplied by the wall pad manufacturer. 3. Panels to be supplied with a no nail margins and to be mounted to concealed 1-inch- x 3-inch- fir stripping that is attached in 3 continuous horizontal rows to the wall. Panels are affixed to the stripping using a toenail method of nailing. H. Adjusting: 1. Final adjustment of panels to insure a smooth finished appearance 2. Clean and remove any debris from the working area 3. Spot clean panels as may be necessary
LOWER MACUNGIE TOWNSHIP COMMUNITY CENTER ADDITIONS AND RENOVATIONS
SECTION.00 - GYMNASIUM EQUIPMENT PART - GENERAL 0 0. SUMMARY A. This Section includes the following gymnasium equipment that is being supplied and installed by the Owner. The Contractor shall provide the
More informationA. This section includes pre-finished Higuera Hardwoods bamboo flooring and accessories for floors and stairs.
SECTION PART 1 - GENERAL 1.1 SUMMARY A. This section includes pre-finished Higuera Hardwoods bamboo flooring and accessories for floors and stairs. 1.2 RELATED DOCUMENTS A. Related Sections include the
More informationA. This Section includes the following: 1. Bulletproof modular counter with Security Glazing in following levels:
SECTION 111510 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to
More informationSECTION SOUND-ABSORPTIVE PANELS
SECTION 09 77 23 SOUND-ABSORPTIVE PANELS PART 1 - GENERAL 1.1 CONDITIONS AND REQUIREMENTS A. The General Conditions, Supplementary Conditions, and Division 01 General Requirements apply. 1.2 SECTION INCLUDES
More informationACOUSTICAL WALL TREATMENT SECTION 09840
ACOUSTICAL WALL TREATMENT PART 1 GENERAL 1.1 SUMMARY A. Section Includes: Site-fabricated, stretched fabric acoustical wall system built with rigid polymer stretching system to secure fabric over the wall
More informationSECTION SOUND-ABSORPTIVE PANELS
SECTION 09 77 23 SOUND-ABSORPTIVE PANELS PART 1 - GENERAL 1.1 CONDITIONS AND REQUIREMENTS A. The General Conditions, Supplementary Conditions, and Division 01 General Requirements apply. 1.2 SECTION INCLUDES
More informationSECTION PREFABRICATED SHOWER COMPARTMENTS
SECTION 102118 PREFABRICATED SHOWER COMPARTMENTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary General Conditions and Division
More informationSection Wood Veneer Ceiling Tiles Micro Perforated
Section 095426 Wood Veneer Ceiling Tiles Micro Perforated PART 1 GENERAL 1.1 RELATED DOCUMENTS Drawings and general conditions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION WALL AND DOOR PROTECTION
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 10 26 00 WALL AND DOOR PROTECTION SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable to
More informationSection SoundPly LR M25 Acoustic Ceiling Panels
Section 095126 Acoustic Ceiling Panels PART 1 GENERAL 1.1 RELATED DOCUMENTS 1.2 SUMMARY A. Drawings and general conditions of the Contract, including General and Supplementary Conditions and Division 1
More informationSECTION LINEAR WOOD CEILINGS
SECTION 09 54 24 LINEAR WOOD CEILINGS Copyright 2015 Madrid Inc. Section number and title complies with the Construction Specifications Institute s (CSI s) MasterFormat. Specification format conforms to
More informationSECTION STRUCTURAL INSULATED PANELS
SECTION 06120 STRUCTURAL INSULATED PANELS Copyright 2011-2012 Korwall Industries, Inc. - All rights reserved PART 1 GENERAL 1.1 SECTION INCLUDES A. Structural Insulated Roof Panels. B. Structural Insulated
More informationGuide Specifications Section Wood Ceiling Coffers
Guide Specifications Section 09 54 33 Wood Ceiling Coffers SECTION 09 54 33 WOOD COFFERED CEILINGS Wood Ceiling Coffers by are a striking solution for beautiful wood ceilings with visual depth. Two styles
More informationCOMPOSITESIDING
SECTION 074643 COMPOSITE SIDING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION PANEL SIGNAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 101423 - PANEL SIGNAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationProduct Guide Specification
Product Guide Specification Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat,
More informationADDENDUM NO. 5. April 9, 2014
CLASSROOM & ACADEMIC OFFICE BUILDING PROJECT NO.: 900290 Project Name: CLASSROOM & ACADEMIC OFFICE BUILDING Project No.: 900290 ADDENDUM NO. 5 to the CONTRACT DOCUMENTS April 9, 2014 I. Bidder acknowledges
More informationSECTION SERIES ALL GLASS ENTRANCES
1 SECTION 08 4210 1200 SERIES ALL GLASS ENTRANCES PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Vestibule doors matching entrance doors. 2. Sidelites. B. Related work in other sections: 1.
More informationSection Wood Veneer Ceiling Planks Linear
Section 095426 Wood Veneer Ceiling Planks Linear PART 1 GENERAL RELATED DOCUMENTS SUMMARY Drawings and general conditions of the Contract, including General and Supplementary Conditions and Division 1
More informationSECTION VINYL-COATED FABRIC WALL COVERINGS
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 09 72 16 VINYL-COATED FABRIC WALL COVERINGS SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationGuide Specification for: FABRI TRAK PVC FREE Stretched Fabric Wall System Section [ ] or Section [ ]
Guide Specification for: FABRI TRAK PVC FREE Stretched Fabric Wall System Section [09 77 13] or Section [09 84 14] 1.0 GENERAL 1.01 Scope A. Furnish and install GeoTRAK Stretched Fabric Wall System produced
More informationSECTION DEMOUNTABLE WALLS SKY WALLS - STRATUS SYSTEM
1 SECTION 10.22.19 DEMOUNTABLE WALLS SKY WALLS - STRATUS SYSTEM PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Full height center-glazed, butt-jointed partition system. 2. Full height doors.
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 12/12/2018
SECTION 08 1416 - FLUSH WOOD DOORS GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION SOLID SURFACE FABRICATIONS
SECTION 06651 SOLID SURFACE FABRICATIONS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the contract, including general and supplementary conditions and Division 1 Specification
More informationProduct Guide Specification
February 2015 528 Pioneer Parkway Clare, Michigan 48617 Toll Free 800-631-0212 Website www.tranquilsystems.com E-mail sales@tranquilsystems.com Product Guide Specification Tranquil Acoustic Walls with
More informationSection HIGH-TENSION Stretched-Fabric Wall Systems SoftWalls, Inc.
P a g e 1 PART I. GENERAL 1.01 Scope A. Furnish and install SoftWalls HIGH-TENSION Acoustical & Tackable Stretch Fabric Systems B. Related Work Specified Elsewhere: 1.Preparation of a smooth, flat and
More informationSeries 3000 Pocket Doors
Series 3000 Pocket Doors Introduction: The following three (3) part specification offers the Standard and Optional features for the Series 3000 Pocket Doors. The yellow highlighted areas in the specification
More informationTotTurf EPDM Product Specification
TotTurf EPDM Product Specification PART 1 GENERAL 1.01 POURED IN PLACE PLAYGROUND SURFACING TotTurf EPDM poured in place rubber playground surfacing shall consist of a polyurethane binder mixed with 100%
More informationINTERIOR FINISHES CHAPTER 8
CHAPTER 8 INTERIOR FINISHES SECTION 801 GENERAL 801.1 Scope. Provisions of this chapter shall govern the use of materials used as interior finishes, trim and decorative materials. 801.1.1 Interior finishes.
More informationSpecifications for LiteWeight Wall Padding: LW7007
Specifications for LiteWeight Wall Padding: LW7007 shall use minimum of 2.2 lb density. Nominal Foam thickness of 1.50" - 1.65" closed-cell cross-link polyethylene foam core. am shall be manufactured with
More informationINTERIOR FINISHES CHAPTER 8
CHAPTER 8 INTERIOR FINISHES SECTION 801 GENERAL 801.1 Scope. Provisions of this chapter shall govern the use of materials used as interior finishes, trim and decorative materials. 801.2 Interior wall and
More informationSection SoundPly RF M25 Acoustic Wall Panels
Section 097714 Acoustic Wall Panels PART 1 GENERAL 1.1 RELATED DOCUMENTS 1.2 SUMMARY A. Drawings and general conditions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSECTION DEMOUNTABLE PARTITIONS
SECTION 10 22 19 DEMOUNTABLE PARTITIONS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationA. Product Data: Identify thermal conductivity, thickness, and jackets (both factory and field applied, if any), for each type of product indicated.
SECTION 23 07 13 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationSECTION PANEL SIGNAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 10 14 23 - PANEL SIGNAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION POLYPROPYLENE FABRIC WALL COVERING
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 09 72 31 POLYPROPYLENE FABRIC WALL COVERING SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. Also delete any other item or paragraph not
More informationSECTION MULTI-USE COMPOSITE ALUMINUM PANELS
SECTION 07416 MULTI-USE COMPOSITE ALUMINUM PANELS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationUniversity of New Hampshire Scholars' Repository
University of New Hampshire University of New Hampshire Scholars' Repository Division 08 Openings Chapter 5 Technical Construction and Renovation Standards 4-23-2015 081410 - Wood Doors Sandra Hickey sandra.hickey@unh.edu
More informationUniversity of New Hampshire Scholars' Repository
University of New Hampshire University of New Hampshire Scholars' Repository Division 08 Openings Chapter 5 Technical Construction and Renovation Standards 4-23-2015 081410 - Wood Doors Sandra Hickey sandra.hickey@unh.edu
More informationSPECIFICATIONS PORTER No PORTABLE BASKETBALL BACKSTOP SYSTEM (FOR INDOOR OR OUTDOOR USE) WITH FAN FIBERGLASS BACKBOARD
SPECIFICATIONS PORTER No. 00535-940 PORTABLE BASKETBALL BACKSTOP SYSTEM (FOR INDOOR OR OUTDOOR USE) WITH FAN FIBERGLASS BACKBOARD Unit is designed for use in elementary schools, training camps, YMCA, park
More informationProduct Guide Specification
Extrutech Plastics, Inc. September 2012 5902 West Custer Street Manitowoc, Wisconsin 54220 Toll Free 888-818-0118 Phone 920-684-9650 Fax 920-684-4344 Website www.epiplastics.com E-mail info@epiplastics.com
More informationPRODUCT SPECIFICATIONS - SERIES 1090
PRODUCT SPECIFICATIONS - SERIES 1090 SECTION 10170 SOLID COLOR REINFORCED COMPOSITE TOILET PARTITIONS PART 1 GENERAL 1.01 Work Included A. Toilet Compartments B. Urinal Screens C. Shower Dividers D. Dressing
More informationSECTION Paper-Composite Countertops PART 1: GENERAL
PaperStone surfaces are slabs made from paper, resin and pigment. For most of the PaperStone products, the paper component is 100% recycled. PaperStone surfaces are fabricated much like solid surfaces
More informationINTERIOR FINISHES CHAPTER 8
CHAPTER 8 INTERIOR FINISHES SECTION 801 GENERAL 801.1 Scope. Provisions of this chapter shall govern the use of materials used as interior finishes, trim and decorative materials. 801.2 Interior wall and
More informationTotTurf Pigmented Poured in Place Product Specifications TOTTURF a PLAYCORE company July 2011
PART 1 General TotTurf Pigmented 1.01 TotTurf PIGMENTED POURED IN PLACE PLAYGROUND SURFACING TotTurf Pigmented poured in place rubber playground surfacing shall consist of a polyurethane binder mixed with
More informationPhenolic Exterior Wall Cladding
Phenolic Exterior Wall Cladding SECTION 07 42 43 COMPOSITE WALL PANELS This specification includes hidden text for editing for a project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Phenolic wall
More informationWC SERIES SPECIFICATION SECTION ACCESS FLOORING
PART 1 - GENERAL 1.1 Section Includes A. Work of this section includes, but is not limited to: access floor panels, factory applied floor finishes, understructure, grommets, cut outs and grounding connectors.
More informationSECTION ALL GLASS ENTRANCES. 1. Lock cylinders for tempered glass entrance doors are specified in Division 8 section Finished Hardware.
1 SECTION 08 4210 ALL GLASS ENTRANCES PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Vestibule doors matching entrance doors. 2. Sidelites. B. Related work in other sections: 1. Lock cylinders
More informationINTERIOR FINISHES CHAPTER 8 SECTION 801 GENERAL
CHAPTER 8 INTERIOR FINISHES SECTION 801 GENERAL 801.1 Scope. Provisions of this chapter shall govern the use of materials used as interior finishes, trim and decorative materials. 801.1.1 Interior finishes.
More informationDSC BUILDING 1200 ALTERATIONS OCTOBER 2011 SECTION DUCT INSULATION
SECTION 230713 DUCT INSULATION PART 1 GENERAL 1.1 SUMMARY A. Related Sections: 1. 233113 Ductwork and Accessories 1.2 REFERENCES A. American Society for Testing and Materials (ASTM): 1. E84-96a Test Method
More informationSECTION CRL70 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS
Page 1 of 6 SECTION 08 32 20 CRL70 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS [OR WOOD] PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,
More informationProduct Guide Specification
VT Industries, Inc. April 2014 1000 Industrial Park PO Box 490 Holstein, Iowa 51025 Toll Free (800) 827-1615 Phone (712) 368-4381 Fax (712) 368-4111 Website www.vtindustries.com E-mail door_info@vtindustries.com
More informationE. Popcorn or other spray applied textures on ceiling or walls are not acceptable.
DIVISION 9 09 2000 GYPSUM BOARD ASSEMBLIES A. Drywall finish: Drywall finishing to conform to Level 5 finish in accordance with Association of Wall and Ceiling Industries (AWCI). Drywall MUST continue
More informationAcoustic Surfaces. Horizontal Bar
Acoustic Surfaces Horizontal Bar The strong graphic surface of Horizontal Bar conceals a workhorse acoustic substrate. Beneath the wool felt face is a high-performance, thermally-formed acoustic panel
More informationDivision 9 Resilient Athletic Flooring
Division 9 Resilient Athletic Flooring TRACKDECK 8mm ROLLED RUBBER FLOORING Specifier Note: The following CSI (Construction Specifications Institute) section describes the resilient athletic flooring system
More informationSECTION DRY ERASE COATING (IdeaPaint CREATE Black and White) A. Section Gypsum Board Assemblies; gypsum board substrate.
Guide Specifications for Designers and Specifiers: This document specifies IdeaPaint CREATE Dry Erase Coating by IdeaPaint, and is provided for your use in CSI 3-Part Format. For further assistance, call
More informationSECTION TOILET COMPARTMENTS. A. Section Metal Fabrications: Concealed steel support members.
SECTION 10155 TOILET COMPARTMENTS PART 1 GENERAL 1.1 SECTION INCLUDES A. Plastic laminate partitions. 1.2 RELATED SECTIONS A. Section 05500 - Metal Fabrications: Concealed steel support members. B. Section
More informationB. LEED Submittals (Projects authorized for LEED certification only)
SECTION 10 21 16 - SHOWER AND DRESSING COMPARTMENTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION ACCORDION FOLDING PARTITIONS
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 10 22 26.13 ACCORDION FOLDING PARTITIONS SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationNorthpointe Renovation EPN #1701 F/A Prroject #17027 September 8, 2017
SECTION 101423.16 - ROOM-IDENTIFICATION PANEL SIGNAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationRESILIENT ACCESSORIES
INCLUDING COVE CAP, CHAIR RAIL, CORNER GUARD, TUB MOULDING, COVE FILLER STRIP AND SUBFLOOR LEVELER SYSTEM THIS DOCUMENT IS INTENDED AS A SUGGESTED GUIDE FOR CREATING, MODIFYING, OR EDITING YOUR CSI FORMATTED
More informationProduct Guide Specification
February 2015 528 Pioneer Parkway Clare, Michigan 48617 Toll Free 800-631-0212 Website www.tranquilsystems.com E-mail sales@tranquilsystems.com Product Guide Specification Tranquil Acoustic Walls with
More informationENVELOPE The Ultimate In Performance In A Dry-Joint System RAINSCREEN (RS) SYSTEM TECHNICAL MANUAL
ENVELOPE 2000 RAINSCREEN (RS) SYSTEM The Ultimate In Performance In A Dry-Joint System TECHNICAL MANUAL System Assembly Substrate Layouts CAD Sections/Details Physical Properties Performance Properties
More informationPRODUCT SPECIFICATIONS PULTRUDED GRATING AND TREADS SECTION PART 1 GENERAL
PRODUCT SPECIFICATIONS PULTRUDED GRATING AND TREADS SECTION 06600 PART 1 GENERAL 1.1 Related Documents A. Drawings and general provisions of Contract, including General and Supplementary Conditions and
More informationHigh-performance structural cement-bonded particle board (CBPB)
High-performance structural cement-bonded particle board (CBPB) for floors, roofs and walls fire resistant moisture resistant durable exceptional strength exceptional value THE PRODUCT Versaroc is a high-performance
More informationSection Performance Floor Asemblies (Also Dance Floor Assemblies)
Sample Specifications for kiwifloor Studio System Section 09646 Performance Floor Asemblies (Also Dance Floor Assemblies) PART 1 GENERAL 1.1 GENERAL A. Work of this Section, as shown or specified, shall
More informationSECTION WOOD GYMNASIUM FLOORING
HORNER MULTISPORT ULTRA SYSTEM Page 1 of 1 SECTION 096466 --- WOOD GYMNASIUM FLOORING PART 1-GENERAL 1.1 DESCRIPTION A. This document specifies a wood strip athletic floor system consisting, in general,
More informationAMBICO Limited Section and WOOD BULLET RESISTANT DOORS AND FRAMES Page 1
Page 1 This section includes Bullet Resistant, Wood Doors and Bullet Resistant Steel Frames which meet the UL752 Standard for Bullet-Resisting Equipment. This section relies on both the Canadian Steel
More informationMulti-Institutional Academic Health Science & Research Center Evansville, IN
SECTION 06 4216 - FLUSH WOOD PANELING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationFeatures. Specifications. VersaShield MBX slashes up to half the total cost with a quick and effective concrete moisture mitigation up to 99.5% RH.
VersaShield MBX slashes up to half the total cost with a quick and effective concrete moisture mitigation up to 99.5% RH. Features Protects against alkalinity and moisture in concrete up to 99.5% RH Reduces
More informationSECTION WOOD GYMNASIUM FLOORING
HORNER VARI-CUSHION SYSTEM Page 1 of 3 SECTION 096466 --- WOOD GYMNASIUM FLOORING PART 1-GENERAL 1.1 DESCRIPTION A. This document specifies a wood strip athletic floor system consisting, in general, of
More informationSECTION SOLID SURFACE COUNTERTOPS. Display hidden notes to specifier. (Don't know how? Click Here)
SECTION 06415 SOLID SURFACE COUNTERTOPS Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Countertops B. Integral sinks C. Splashes D. Setting materials
More informationINTERIOR FINISH, DECORATIVE MATERIALS AND FURNISHINGS
CHAPTER 8 INTERIOR FINISH, DECORATIVE MATERIALS AND FURNISHINGS SECTION 801 GENERAL 801.1 Scope. The provisions of this chapter shall govern interior finish, interior trim, furniture, furnishings, decorative
More informationSECTION FABRICATED WALL PANEL ASSEMBLIES. A. American Institute of Steel Construction (A.I.S.C.) "Manual of Steel Construction.
SECTION 07 42 63 FABRICATED WALL PANEL ASSEMBLIES PART 1 GENERAL 1.1 SECTION INCLUDES A. Provide ACCEL-E steel thermal-efficient-panel wall system. 1.2 RELATED SECTIONS A. Section 05 40 00 - Cold Formed
More informationSECTION FIBERGLASS REINFORCED POLYMER (FRP) PANELS
SECTION 07 44 50 FIBERGLASS REINFORCED POLYMER (FRP) PANELS PART 1 - GENERAL 1.1 SECTION INCLUDES A. Design, Engineering, manufacturing and erection of fiberglass reinforced panels. Delegated Design of
More informationTotTurf TPV (1-4mm) Product Specification
TotTurf TPV (1-4mm) Product Specification PART 1 GENERAL 1.01 POURED IN PLACE PLAYGROUND SURFACING TotTurf TPV poured in place rubber playground surfacing shall consist of a polyurethane binder mixed with
More informationPRODUCTION SPECIFICATIONS INSULATED CONCRETE FORMS
PRODUCTION SPECIFICATIONS SECTION 03135 INSULATED CONCRETE FORMS PART 1 GENERAL 1.1 SECTION INCLUDES A. Insulated panel permanent concrete form system for: 1. Exterior structural wall panels. 2. Interior
More informationPRODUCTION SPECIFICATIONS INSULATED CONCRETE FORMS
PRODUCTION SPECIFICATIONS SECTION 03135 INSULATED CONCRETE FORMS PART 1 GENERAL 1.1 SECTION INCLUDES A. Insulated panel permanent concrete form system for: 1. Exterior structural wall panels. 2. Interior
More informationC. Samples: For each door face material, at least 3 by 5 inches (75 by 125 mm) in size, in specified finish.
SECTION 083113 - ACCESS DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION FLUSH WOOD DOORS
SECTION 081416 PART 1 - GENERAL 1.1 SUMMARY Section Includes: 1. Solid-core doors with wood-veneer faces. 2. Solid-core doors with MDO faces for opaque finish. 3. Pocket doors for folding fire doors. 4.
More informationTotTurf Bonded TotTurf Bonded Poured in Place Product Specifications TOTTURF a PLAYCORE company May 2011
PART 1 General TotTurf Bonded 1.01 POURED IN PLACE PLAYGROUND SURFACING TotTurf Bonded poured in place playground surfacing consists of a polyurethane binder mixed with 100% recycled, shredded tire material
More informationA. This Section includes duct and plenum insulation; accessories and attachments; and sealing compounds.
SECTION 230713 DUCT INSULATION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION TRESPA ATHLON SOLID COMPOSITE PHENOLIC TOILET PARTITIONS. A. Solid composite phenolic toilet compartments and urinal screens.
SECTION 102113 TRESPA ATHLON SOLID COMPOSITE PHENOLIC TOILET PARTITIONS PART 1 - GENERAL 1.01 SECTION INCLUDES A. Solid composite phenolic toilet compartments and urinal screens. 1.02 RELATED SECTIONS
More informationSpec Master 5/7/ For each product requiring color and texture selection, provide full size samples.
SECTION 04812 (042012) MECHANICALLY ATTACHED BRICK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationC. Low-Emitting Materials: Provide doors made with adhesives and composite wood products that do not contain urea formaldehyde.
SECTION 08 1416 - FLUSH WOOD DOORS PART 1 - GENERAL 1.1 SECTION REQUIREMENTS A. Submittals: Samples for factory-finished doors. PART 2 - PRODUCTS 2.1 FLUSH WOOD DOORS A. Manufacturers: Subject to compliance
More informationSustainability Our journey to provide Sustainable furniture solutions
Sustainability Our journey to provide Sustainable furniture solutions RT London + Sustainability Sustainability is a complex subject. For many people, Sustainability translates into being environmentally
More informationGeometrik Manufacturing Inc.
PRODUCT: GEOSQUARE WOOD TILES Page 1 PART I GENERAL 1.1 SECTION INCLUDES 1. GeoSquare wood [acoustical] ceiling tiles. 2. Coordination with other trades that have parts attached to, penetrate through or
More informationSection Wood Grille Ceiling Panels
Section 095426 Wood Grille Ceiling Panels PART 1 GENERAL RELATED DOCUMENTS Drawings and general conditions of the Contract, including General and Supplementary Conditions and Division 1 Specification sections
More informationEast Central College
SECTION 123623 - PLASTIC-LAMINATE-CLAD COUNTERTOPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationZeager Bros. Inc. Middletown, Pa / Zeager Hardwood Co. Franklin, Ky Revised - August, 2012 by ASC
Product Guide Specification 32 18 16.13 RECMAT Protective Playground Surfacing Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI)
More informationSPECIFICATIONS ADVANTAGES. For more information on this product or to order samples call or visit our website at builddirect.
Insulayment is a unique, earth-friendly, insulating underlayment that helps absorb impact sound so it won t transfer to lower level rooms; suppresses the effect of concrete sub-floor cracking to protect
More informationFramed Decorative Panel Systems
Note: This document contains information and notes in hidden text. If you need assistance to view & hide text, instructions are at this link: http://www.marlite.com/hidden-notes-instructions.aspx Delete
More informationSECTION EZ-SLIDE 80 AND 180 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS
Page 1 of 6 SECTION 08 32 20 EZ-SLIDE 80 AND 180 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,
More informationfeaturing: RR (Rout & Return) Attachment System RS (RainScreen) Attachment System Envelope2000 Metal Composite Material (MCM)
featuring: RR (Rout & Return) Attachment System RS (RainScreen) Attachment System Envelope2000 Metal Composite Material (MCM) THE ULTIMATE IN BEAUTY AND PERFORMANCE. As shop-fabricated systems, the RR
More informationSoundmaster & Modernfold TECHNICAL DATA
This specification along with product information and model details can be downloaded from www.modernfold.com SPECIFICATION - SECTION 08 35 13 ACCORDION FOLDING DOORS PART 1 - GENERAL 1.1 RELATED DOCUMENTS
More informationHARO SPORTS FLOOR C.S.I. GUIDE SPECIFICATION Helsinki-Gymnasium Floor System 10/2010 SECTION WOOD ATHLETIC FLOORING
HARO SPORTS FLOOR C.S.I. GUIDE SPECIFICATION Helsinki-Gymnasium Floor System 10/2010 SECTION 09 64 66 WOOD ATHLETIC FLOORING PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Wood athletic flooring including
More informationSECTION CLIMBING WALLS
SECTION 13120-1 PART 1 - GENERAL 1.1 SUMMARY A. This section includes the following: 1. Custom Climbing Wall. B. Related Sections 1. Section Structural Steel 2. Section Rough Carpentry 3. Finishes 1.2
More informationFaçade Architectural Wall Panel System - Guide Specification 3/11/2017 SECTION FRAMED DECORATIVE PANEL SYSTEMS PART 1 - GENERAL 1.
SECTION 09 7710 FRAMED DECORATIVE PANEL SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: Decorative ½ / ¾ (13mm/19mm) thick prefinished panel with preengineered attachment clip along with hardware
More informationSECTION CRL50 AND CRL51 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS
SECTION 08 32 20 CRL50 AND CRL51 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS Page 1 of 6 USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,
More informationSECTION LAGUNA SERIES TOP HUNG SLIDING DOOR SYSTEM
Page 1 of 6 SECTION 08 32 20 LAGUNA SERIES TOP HUNG SLIDING DOOR SYSTEM USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS SLIDING DOORS. SECTION INCLUDES OVERHEAD SLIDING TUBE ASSEMBLY, MOUNTING
More information