Specifications for LiteWeight Wall Padding: LW7007

Transcription

1 Specifications for LiteWeight Wall Padding: LW7007 shall use minimum of 2.2 lb density. Nominal Foam thickness of 1.50" " closed-cell cross-link polyethylene foam core. am shall be manufactured with easy-to-roll, flexible tambour-cut slits to allow for quick handling. face shall use a non-woven, polyester backed reinforced vinyl scrim with a hot-spray application of #457 Poly-vinyl coating for added durability and aesthetic appeal. The surface shall be heat-laminated onto the foam core. -- Mats finished with 20 oz to 24 oz Vinyl Fabric surfaces are NOT acceptable. Wrestling mat shall be available in 27 color options. anufacturer shall be able to provide layout, design and placement. full-color, computer rendering with graphics for review for Warranty -- Vinyl surface guaranteed at least 3 years from the date of shipment against manufacturing defects. Wrestling Mat Manufacturer shall be able to provide customized mat sizes and configurations as needed. LW7007-REV: 0 7 SPT LW7007

2 RESILITE: LW LiteWeight Wall Mat Specification Sheet Physical Properties: polymur Crosslinked Polyethylene ( XLPE ) foam core color weight thickness (nominal) vinyl scrim Black 0.55 (lb/ft2) (in) Non-woven backed, reinforced vinyl scrim coating Resilite #457 Polyvinyl Formula Other Specifications: ASTM D-3575 Compression 25% (psi) ASTM D-3575 Compression 50% 25 max (%) ASTM D-3575 Density 2.2 (lb/ft3) ASTM D-3575 Water Absorption % <0.06 (lb/ft2) ASTM D-3575 Tensile (psi) ASTM D-3575 Elongation 100 min. (%) FMVSS302 Flammability : > 1/4" Pass Working Temperature Range -65 F 200 F ASTM F Standard Specification for Competition Wrestling Mats Meets or Exceeds ASTM F Test method for shock absorbing properties (Type I or Type II) Pass G-Max (<) 100 max. ASTM F Impact Attenuation for surfacing materials (Free-Fall method) Pass HIC (<) 1000 max. Pass G-Max (<) 200 max. Resilite provides this information as a technical service. To the extent the information is derived from sources other than Resilite, resilite is substantially, if not wholly, relying upon other sources to provide accurate information. Each user of these products, or information should perform their own testing to determine the safety and suitabiltiy of the products. Since Resilite cannot control the end use of this product, Resilite does not guarantee that the user will obtain the same results published in this document. The data herein contained is provided as a service. The information is subject to change without notice. Resilite Sports Products, Inc. PO Box 764 Sunbury, PA Phone:

3 INSTALLATION DETAILS FOR LITEWEIGHT WALL PADDING -- PLEASE READ CAREFULLY BEFORE BEGINNING INSTALLATION-- Item #LW RESILITE SPORTS PRODUCTS, INC. ALL RIGHTS RESERVED

4 INSTALLATION DETAILS FOR LITEWEIGHT WALL PADDING -- PLEASE READ CAREFULLY BEFORE BEGINNING INSTALLATION-- Item #LW7007 Any activity involving motion, height, wall collisions or physical contact creates the possibility of serious injury, even death. Resilite mats do not totally eliminate this hazard. The following guidelines should always be followed when using Resilite cushioned wall mats PAGE 2

5 TOOLS NEEDED 1 1 INSTALLING PADDING ON THE WALL STEP 1: Determine Height W W STEP 2: Apply Adhesive Tape T STEP 3: PAGE 3

6 INSTALLING PADDING ON THE WALL STEP 4: Apply Male Edge Cap Retainer LW Edge Cap Male RETAINER FIG 1 FLOOR SURFACE PAGE 4 SPT

7 INSTALLING PADDING ON THE WALL STEP 5: Apply The Wall Padding LW Edge Cap Male RETAINER WALL PADDING FIG 2 FLOOR SURFACE PAGE 5

8 INSIDE CORNERS TOP VIEW OF WALL 1 INSIDE CORNERS -- For Inside Corners, Lap Padding -- Run 1st pad into Corner -- Butt the 2nd Pad Against the 1st INSTALL THIS PADDING FIRST OUTSIDE CORNERS OUTSIDE CORNERS -- For Outside Corners, Remove a section of the foam as shown below. -- Cut Out the Foam on a 45 Angle to Create a V Notch. -- DO NOT ut hrough the Front Surface of the Panel. TOP VIEW OF WALL 3 FIG. 3 PAGE 6

9 INSTALLING PADDING ON THE WALL STEP 6: Finish the Edge Cap Trim LW Edge Cap Female TRIM NOT FLOOR SURFACE PAGE 7

10 200 POINT TOWNSHIP DRIVE NORTHUMBERLAND, PA THE-MATS /