SECTION (08410) - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS

Size: px

Start display at page:

Download "SECTION (08410) - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS"

Gabriel Ross
6 years ago
Views:

1 SECTION (08410) - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Interior and Exterior Aluminum Storefront Framing, Doors, Door Frames, Lights, and Fixed Windows. 1. Aluminum Framed Interior Glass Partition Wall System with Sliding Glass Panels a. College Room 2. Anchors, Brackets, and Attachments 3. Door Hardware 4. Perimeter Sealant B. Work Installed but Furnished Under Other Sections: 1. Section (08710) - Door Hardware: Additional Door hardware items other than specified in this Section, and keying requirements. C. Related Sections: 1.02 REFERENCES A. American Architectural Manufacturers Association (AAMA) Publications: 1. AAMA Storefront and Entrance Manual "Care and Handling of Architectural Aluminum from Shop to Site" / "Cleaning and Maintenance Guide for Architecturally Finished Aluminum" Voluntary Specification for Anodized Architectural Aluminum "Voluntary Specification, Performance Requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels" "Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on Aluminum Extrusions and Panels" "Voluntary Specification, Performance Requirements and Test Procedures for Superior Performing Organic Coatings on Aluminum Extrusions and Panels" B. American National Standards Institute (ANSI) Publications: 1. ANSI/AAMA 101 "Voluntary Specifications for Aluminum, Vinyl (PVC) and Wood Windows and Glass Doors" C. ASTM International (ASTM) Publications: 1. A36 Standard Specification for Carbon Structural Steel 2. A123 Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products 3. A653 "Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process" PAGE 1 FILE: CFRST-Aluminum-Framed Entrances and Storefronts REVISED: 06/06/ , Marriott International, Inc. CFRST SPECMSTR-NEW BUILD

2 4. B221 "Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes" 5. E236 "Standard Specification for Apparatus For Microdetermination Of Alkoxyl Groups" 6. E283 Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen 7. E330 Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference 8. E331 Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference D. National Fenestration Rating Council (NFRC) E. Underwriter's Laboratories, Inc. (UL) Standards F. Glass Association of North America (GANA) Publications 1.03 SUBMITTALS 1. Glazing Manual 2. Laminated Glazing Reference Manual 3. GANA Bulletin , Proper Procedures for Cleaning Architectural Glass Products A. General: Submit the following in accordance with Conditions of Contract and Division 01 Specification Sections. B. Submit Letter of Conformance in accordance with Section (01330) indicating specified items selected for use in project with the following supporting data. 1. Submit Shop Drawings and product data and manufacturer's installation instructions. Include system and component dimensions; components within assembly; framed opening requirements and tolerances; anchorage and fasteners; glass and infills; door hardware requirements; and affected related work QUALITY ASSURANCE a. Field Measurements: Verify opening and layout dimensions of glass partition system by field measurements prior to fabrication and record measurements on Shop Drawings. A. All systems to provide for expansion and contraction within system components caused by a cycling temperature range of 170 degrees F. without causing detrimental effects to system or components. B. Qualifications: 1. Manufacturer: [Glass partition and ]Storefront manufacturer to have minimum five (5) years documented experience in the fabrication of glass partitions of the type required for this project and be capable of providing field service representation during installation. 2. Installer: Minimum two (2) years documented experience in work of this Section and approved by each partition system manufacturer. C. Source Limitations: Obtain Glass Partition System materials from one manufacturer for entire Project, unless otherwise acceptable to Architect. D. Exterior Systems: PAGE 2 REVISED: 06/06/16 FILE: CFRST-Aluminum-Framed Entrances and Storefronts CFRST SPECMSTR-NEW BUILD 2016, Marriott International, Inc.

3 1. Design for windload of 30 PSF with maximum deflection in both vertical and horizontal mullions not to exceed 1/175 of span. 2. Comply with the applicable standards of ANSI/AAMA 101 and the following: a. AAMA 10 b. AAMA 2603 c. AAMA 609/ Certify that the proposed products have been tested to the following performance standards at an Independent Testing Laboratory accredited by AAMA and using the referenced ASTM standards: a. Water Penetration: ASTM E331 no water penetration at a test pressure of 6.24 PSF. b. Structural Properties: 30 PSF acting inward and outward per ASTM E330. Deflection not to exceed 1/175 of span. c. Air Leakage per ASTM E283: 1) Fixed window walls - maximum of 0.06 CFM per sq. ft. of total exterior surface areas. d. Thermal Performance: Composite glass wall shall meet or exceed the "U" value shown on the Drawings and as tested per ASTM E Drain water entering joints, condensation occurring in glazing channels, or migrating moisture occurring within system, to exterior. E. Glass Partition Wall System Performance / Design Criteria 1. Impact Safety Resistance: CPSC 16 CFR 1201, Cat. I & II 2. Design Criteria: a. Structural - Live Load: Glass partition system to be designed to withstand live loads in accordance with governing state and federal codes, rules and regulations of the authority having jurisdiction (AHJ). 1) Deflection: Maximum L/ Structural Stability: Meet requirements of BS 5234 (partition structural requirements), and BS 6180 (protective barriers) a. Partitions installed under IBC to be laterally supported in accordance with IBC Section , ASCE 7 Section b. Seismic Requirements under provisions of IBC Section F. All systems shall accommodate, without damage to system or components, or deterioration of perimeter seal: Movement within system; movement between system and perimeter framing components; dynamic loading and release of loads; and deflection of structural support framing DELIVERY, STORAGE, AND HANDLING A. Transportation and Handling: Transport products by methods to avoid product damage; deliver in undamaged condition in manufacturer's unopened containers or packaging, dry. Provide equipment and personnel to handle products by method to prevent soiling or damage. Promptly inspect shipments to assure that products comply with requirements, quantities are correct, and products are undamaged. PAGE 3 FILE: CFRST-Aluminum-Framed Entrances and Storefronts REVISED: 06/06/ , Marriott International, Inc. CFRST SPECMSTR-NEW BUILD

4 B. Storage and Protection: Store products in accordance with manufacturer's instructions, with seals and labels intact and legible. Store sensitive products in weather-tight enclosures; maintain within temperature and humidity ranges required by manufacturer's instructions SPECIAL WARRANTY A. Aluminum Storefront System: 1. The work of this Section shall be jointly guaranteed by the manufacturer for a period of five (5) years after the date of Substantial Completion. B. Aluminum Framed Interior Glass Partition Wall System with Sliding Glass Panels: 1. The work of this Section shall be jointly guaranteed by the manufacturer for a period of one (1) year after the date of Substantial Completion. C. All materials shall be free from manufacturing defects and defects in installation workmanship. Any material or workmanship judged defective during this period shall be removed and replaced at no cost to the Owner. PART 2 PRODUCTS 2.01 MANUFACTURERS A. For purpose of designating design and quality of aluminum storefront system, fixed window system, Drawings and Specifications are based on the following: 1. Storefront and Fixed Window Framing System: Insulated Glazing (Tempered) a. Avendra, LLC Preferred Manufacturers: 1) None b. Approved Manufacturers: 2. Entry Doors: 1) "Trifab VersaGlaze 451T", Kawneer North America, an Alcoa Company. ( ) 2) FG-3000 MultiPlane", Oldcastle BuildingEnvelope (formally Vistawall) ( ) 3) System 403 T, EFCO Corporation ( ) a. Style and rail tubular member door framing system by same manufacturer of storefront framing system, compatible with specified framing system. b. Style: Wide style, as indicated on Drawings. c. Thermal Construction: [High-performance plastic connectors separate aluminum members exposed to the exterior from members exposed to the interior] <Insert description>. d. Provide nonremovable glazing stops on outside of door ALUMINUM FRAMED INTERIOR GLASS PARTITION WALL SYSTEM WITH SLIDING GLASS PANELS A. Avendra, LLC Preferred Manufacturers: 1. None B. Approved Manufacturers: 1. RS3000 System ; Richelieu America PAGE 4 REVISED: 06/06/16 FILE: CFRST-Aluminum-Framed Entrances and Storefronts CFRST SPECMSTR-NEW BUILD 2016, Marriott International, Inc.

5 a. Contact: Michael Baer ( ) 2. MCY2000 System ; Hafele America, Hospitality Group a. Contact: Ty LeFever ( ) C. System Description: 1. Full Height Aluminum Single-glazed partition system. Provide all components required for a complete system including a total of four (4) Framed Panels (framed on 4 Sides) with Two (2) Stationary and Two (2) Sliding Panels that slide behind Fixed Panels on Business Library side. No intermediate framing will be permitted. All four (4) panels shall be of equal width. a. System shall be designed to be capable of withstanding normal impact loads. 2. Aluminum Framing: Maximum 2 x 4. Match adjacent Exterior framing as close as possible. 3. Guide System: Shall be one of the following: a. Bottom Rolling, Top Guide 1) Top of bottom track to be flush with top of finished floor material. Refer to Drawings and Interior Finish Index for materials. Basis of Design is the Tile Channel by Richelieu America, or equivalent by other listed manufacturers. b. Top Supported System: 1) Top-hung roller system with a guide at the bottom. 4. Systems shall have internal leveling system, and be adjustable for field conditions. 5. Size: Panels to be equal widths, as shown on Drawings 6. Glazing: Custom Decorative Laminated Glass supplied by Section Glazing a. Overall Thickness: 3/8 b. Refer to Interior Finish Index for Decorative Glazing. 7. Regulatory Requirements: Provide tempered or laminated safety glass for locations subject to human impact as required by the governing codes, rules, and regulations of authorities having jurisdiction (AHJ). 8. Hardware: Provide all required hardware, anchors, seals and miscellaneous trim necessary to complete all work. Lock and pulls are not required. D. Materials: 2.03 MATERIALS 1. Aluminum Extrusions: ASTM B221, 6063-T6 alloy and temper 2. Stainless Steel: ASTM A276, Type Fasteners: Type best suited to application, and acceptable to glass partition system manufacturer. A. All framing members shall be extruded aluminum of 6063T-5 alloy and shall be of the size, shape, and intended function as shown on the Drawings. Performance requirements shall conform to standards established by the Architect in relation to wind load and deflection limits. B. Fasteners: Stainless Steel PAGE 5 FILE: CFRST-Aluminum-Framed Entrances and Storefronts REVISED: 06/06/ , Marriott International, Inc. CFRST SPECMSTR-NEW BUILD

6 2.04 FINISH: A. Comply with NAAMM's "Metal Finishes Manual for Architectural and Metal Products" for recommendations for applying and designating finishes. B. Storefront Systems: All exposed aluminum surfaces shall have a manufactured-applied, 10 - year warrantied, [AAMA 2604] [AAMA 2605] Fluoropolymer coating not less than [50%] [70%] polyvinylidene fluoride resin by weight finish, free from blemishes and surface defects. 1. Selected by Architect from standard non-metallic colors available. C. Glass Partition Wall System Aluminum: All exposed aluminum surfaces shall have a manufactured-applied, 10-year warrantied, AAMA Fluoropolymer coating not less than 50% polyvinylidene fluoride resin by weight finish, free from blemishes and surface defects. Powder coat is an acceptable alternative finish FABRICATION 1. Color to match adjacent exterior storefront framing system. A. Storefront Systems: 1. Aluminum door shall have tight hairline joints where rails are fitted against stiles and shall be fastened by means of tensioned steel tie rods in top and bottom rails. Doors shall have an adjusting mechanism in the toprail to provide for minor clearance adjustments. Glass stops shall be snap-in type with bulb type glazing strips. Weather stripping shall be pile. 2. Store front sections shall be square cut and assembled with the proper clips and screws as provided by the manufacturer to form neat hairline joints. All fastenings shall be concealed except those specifically detailed by the Architect at certain transition areas. All glazing gaskets shall be cut over length and installed in slight linear compression to prevent shrinkage from the corners. All framing shall be erected square and true into correct size rough openings prepared by others and in strict accord with the Architectural Drawings. 3. Doors: Reinforce doors as required for installing hardware, including electronic strikes and card readers. a. At pairs of exterior doors, provide sliding weather stripping retained in adjustable strip mortised into door edge. b. At exterior doors, provide weather sweeps applied to door bottoms. 4. Hardware Installation: Factory install hardware to the greatest extent possible. Cut, drill, and tap for factory-installed hardware before applying finishes. 5. Glass Partition Wall System: a. Fabricate glazing units in sizes indicated by approved shop drawings, with edge and face clearances, edge and surface conditions, and, where indicated, bite complying with written instructions of product manufacturer and referenced glazing publications, to comply with system performance requirements. 1) Clean-cut or flat-grind vertical edges of butt-glazed monolithic lites in a manner that produces square edges with slight kerfs at junctions with outdoor and indoor faces. 2) Grind smooth and polish exposed glass edges and corners. b. Accurately fit and secure joints and intersections. PAGE 6 REVISED: 06/06/16 FILE: CFRST-Aluminum-Framed Entrances and Storefronts CFRST SPECMSTR-NEW BUILD 2016, Marriott International, Inc.

7 c. Make joints flush and hairline. d. Prepare components to receive anchor devices and hardware. Fabricate anchorage items. e. Arrange fasteners, attachments, and jointing to ensure concealment from view STOREFRONT SYSTEM - HARDWARE A. Entrance door hardware shall be supplied with doors as follows, unless indicated otherwise: 1. Continuous Hinges, HD, Hager, Kynar finish, color to match door. 2. Pull, Style CO-9 by Kawneer, or approved substitution by other listed manufacturer, No. 26 Finish. 3. Push, Style CP-II by Kawneer, or approved substitution by other listed manufacturer, No. 26 Finish. 4. Closers, surface mounted type, LCN 4041-CUSH, cover to be STAT. 5. Weather Stripping (3 sides) 6. Bottom Sweep 7. Handicapped Threshold, clear aluminum mill finish. 8. Provide construction cylinder and replace with final cylinder specified in Section (08710). 9. Final cylinders, panic devices, electric strikes and card readers by Section (08710) JOINT SEALANTS A. For metal to metal joints use Standard Products Company Stan Pro Urethane Epoxy Sealant No. 103, Dow Corning Silicone Rubber Sealant, or other as acceptable to [Architect][Owner s Representative], color to match finish of aluminum to which applied. B. For perimeter of framing members, refer to Section (07920) Joint Sealants. PART 3 EXECUTION 3.01 INSPECTION A. Verify wall openings and adjoining air and vapor seal materials are ready to receive work of this Section. B. Beginning of installation means acceptance of existing conditions INSTALLATION A. Install doors, frames, glazing and hardware in accordance with manufacturer's instructions and AAMA Storefront and Entrance Manual guide specifications. B. Install Glass in accordance with Glass Association of North America Glazing Manual and Laminated Glazing Reference Manual. C. Use anchorage devices to securely attach frame assembly to structure. D. Align assembly plumb and level, free of warp or twist. Maintain assembly dimensional tolerances, aligning with adjacent work. E. Tolerances: 1. Maximum Variation from Plumb or Level: 1/8 inch in 3 feet or 1/4 inch in any 10 feet, whichever is less. PAGE 7 FILE: CFRST-Aluminum-Framed Entrances and Storefronts REVISED: 06/06/ , Marriott International, Inc. CFRST SPECMSTR-NEW BUILD

8 2. Maximum Misalignment of Members Abutting End to End: 1/16 inch. F. Coordinate attachment and seal of air and vapor barrier materials. Install sill flashings where required. G. Weathertight Construction: Install sill members and other members in a bed of sealant or with joint filler or gaskets, to provide weathertight construction. 1. Refer to Section Joint Sealants for installation requirements. H. Apply one coat of bituminous paint to concealed aluminum and steel surfaces in contact with cementitious, stone or other dissimilar materials. I. Install glass and infill panels in accordance with Section (08800) using exterior wet method of glazing. J. Install perimeter non-hardening, non-skinning type sealant, and installation requirements in accordance with Section (07920). K. Adjust operating hardware 3.03 TOLERANCES A. Variation from Plane: 0.03 inches per foot maximum or 0.25 inches per 30 feet, whichever is less. B. Misalignment of Two Adjoining Members Abutting in Plane: inches CLEANING A. Remove protective material from prefinished aluminum surfaces. B. Wash-down exposed surfaces using a solution of mild detergent in warm water, applied with soft, clean wiping cloths. Take care to remove dirt from corners. Wipe surfaces clean. C. Remove excess sealant by moderate use of mineral spirits or other solvent acceptable to sealant manufacturer. END OF SECTION PAGE 8 REVISED: 06/06/16 FILE: CFRST-Aluminum-Framed Entrances and Storefronts CFRST SPECMSTR-NEW BUILD 2016, Marriott International, Inc.

Signature Series 5 Lap SECTION ALUMINUM WINDOWS

Signature Series 5 Lap SECTION 08 51 13 ALUMINUM WINDOWS PART 1 GENERAL 1.01 SUMMARY A. Related Documents: Conditions of the Contract, Division 1 - General Requirements, and Drawings apply to Work of this