AVRAAM PITTAKIS & SONS LTD

Transcription

1 AVRAAM PITTAKIS & SONS LTD CONSTRUCTION MATERIAL PRODUCERS Adhesives Grouts Plasters Mortars Compounds Textured Coating Insulation Materials Self Leveling Compounds Primers & Latex 0 Last Revision 04/06/2018

2 Table of Contents ADHESIVES & GROUTS ADHESIVES ALFAKOL 2*... 1 ALFAKOL 3*... 6 ALFAKOL 6* ALFAKOL 11* ALFAKOL 15* ALFAKOL 18* ALFAKOL 24* ALFATHERM Base Coat ALFA-THERM Thick ALFATHERM Top Coat GROUTS ALFA ARMOS PLASTERS & MORTARS PLASTERS RD HAND PLASTER rd HAND PLASTER WITH FIBERS THERMO 3 rd Hand EXELASTIC FLEXIBLE ACRYLIC EXTRA PLAST SMART PLAST THICK SMART PLAST FINE SMARTELASTIC PLAST Thick LIMEPLASTER UNDERCOAT Thick LIMEPLASTER FINISH Fine MORTARS ALFAKOL 1* PITTAKIS CEM THERMOPILOS ALFAREP... 91

3 COMPOUNDS & TEXTURED COATING Compounds FLASHELASTIC SPA THICK ACRYLIC FLASH SPA THICK FLASHELASTIC SPA FINE ACRYLIC FLASH SPA FINE Textured Coating PITTAKIS GRAFIT PARALIMNITIKO MIXED SPRITS ALFALIQ UV THERMAL - Acrylic ALFALIQ UV THERMAL-Silicone ALFALIQ GRAFIT INSULATION MATERIALS & SELF LEVELING COMPOUNDS THERMAL INSULATION PERLOBETON THERMOSOVAS WATERPROOFING MATERIALS ALFA WATER SEAL ALFA LIQUID SEAL SELF LEVELING COMPOUNDS SELF LEVELING COMPOUND (5 30 mm) SELF LEVELING COMPOUND (1 8 mm) PRIMERS & LATEX PRIMERS ALFA BETON REDPRIMER ALFALIQ PRIMER ALFA FERRE ALFALIQ GRAFIT PRIMER LATEX ALFALIQ LATEX

4 CONSTRUCTION MATERIALS PRODUCERS ADHESIVES & GROUTS ADHESIVES & GROUTS 1-48

5 ADHESIVES SERIES 1. ADHESIVES FOR TILES, BLOCKS & STONES Alfakol 2*, Alfakol 3*, Alfakol 6*, Alfakol 11*, Alfakol 15*, Alfakol 18*, Alfakol 24* 2. ADHESIVES FOR XPS or EPS PANELS & Stonewool - Alfa Therm Fine - Alfa Therm Thick 1-44

6 Use-Examples of enforcements: ALFAKOL 2* Alfakol 2* C1TE-Superstrength, Acrylic, Waterproof With null vertical slipping and extended appliance time, for indoor and outdoor use on floors, walls, ceramic and tiles. Also ideal for building Ytong blocks. Preparation of sub layer: For better results we must follow the rules below. The surfaces that the mixture will be placed on different walls or floors have to be well clean from dust, oil, polyurethane, or other material. If the substrates are rusted and destroyed must be carefully cleaned and removed from any other materials. We have to be careful that the area where the mixture is done (bucket), is made by a product which can be easily cleaned. During the preparation of the product, you must be sure that the metals of the spatula or buckets do not have any signs of rust that can affect negatively the chemical reaction and the color of the adhesive. We also have to be careful that the containers we will use are easy to clean and they will always be clean before use. At the end of day, we suggest you clean all the instruments used, because the miss cleaning of the instruments can conclude in bad colors on your final construction. The chemical reactions of the materials can affect the soldering ( in alkali trestle we use primer). The substrate must be a smooth surface, so the use of overdose adhesive is not needed. With this method, we will cover all the anomalies of the floor or wall. Do not forget that all the construction products are producing for the best possible quality, save time and perfect essential result. Preparation of Mixture: We mix 25kg ALFAKOL 2* with roughly 8 liters clean water in a clean container, always with electric stirrer until we achieve uniform pastry. Wait for 5 minutes and mix again. The material is ready for use. ALFAKOL 2* has life in the container for approximately 4 hours when we stir every 1 hour. We do not add water, simply we stir with an electric blender. Most minimum time for light use 24 hours and the time of final use 14 days. 1

7 Directives of Use: 1. We clean and fix the rotten sublayer. 2. Afterwards we should clean the surface by any chance oils, dust, remains of colour etc. 3. The wall does not need any sprinkling either the tiles need any wash. This saves time and money. 4. We stretch out the adhesive with toothed spatula as long as it needs we work for minutes depending on temperature. At temperatures above 23ºC the open time of application decreases and at temperatures under 23ºC, the open time of application increases. We cover the decorated surface with tiles which abstain from each other 2-3 thousandth for expansion and contraction. 5. In order to cover 1 sq.m.of tiles we need 2-5 Kg ALFAKOL 2*. For other uses it depends on type and surface that it will be placed. 2

8 Technical Characteristics: (typical numbers) Alfakol 2* Product definition: Type: Powder Colour: White and grey Specific Gravity: 1.35 kg/lt Composition of dry materials: 100% Storage: 9 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use: Composition of Mixture: Thick Water Requirements: 25kg Powder roughly 8 Liters Water Specific gravity of mixture: 1.62 kg/lt PH Mixture: 13 Self life in bucket: 4 Hours/ mix every 1 hour Application Temperature: 5 ºC ºC Growthing Time: 24 Hours Time for Final use: 14 Days Consumption: 2-5kg/m² Depending on use Strengths: Humidity: Excellent Acids-Alkali: Poor Temperature: -30ºC until+90ºc Declaration tests for marked CE: C1TE Determination of open time: 0,5 Ν/mm² Initial Adherence: 0,9 Ν/mm² Adherence after ageing with HCAT: 0,6 Ν/mm² Adherence after immersion in water: 0,5 Ν/mm² Adherence after freezing-defrosting cycles: 0,7 Ν/mm² Slip determination in vertical wall: 0,5 mm Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 3

9 Declaration of Performance: No.: CPR036-01/07/ Unique identification code of the product-type: ALFAKOL 2* Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: C1TE - Superstrength, acrylic, waterproof, cementitious tile adhesive for indoor & outdoor use on floors & walls. 4.Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 3 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ A notified testing laboratory, the APPLUS, LGAI TECHNOLOGICAL CENTER, S.A, NB 0370, has performed the determination of the product-type on the basis of Initial Type Testing (ITT) under system 3 and issued the test report Nº 08/ In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Extended open time (30 min) Initial adhesion strength Classification C1ΤΕ Performance Class Α1 0,5 Ν/mm² 0,5 Ν/mm² Harmonised Technical Specification ΕΝ 12004: 2012 Adhesion Strength after heat ageing 0,5 Ν/mm² Adhesion Strength after water immersion 0,5 Ν/mm² Adhesion Strength after freeze - thaw cycles 0,5 Ν/mm² Improved slip resistance 0,5 mm 10.The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/2013 4

10 5

11 ALFAKOL 3* Use-Examples of Enforcements: ALFAKOL 3* C2TE-Superstrength, Acrilic, Waterproof with no vertical slip and extended open time, for indoor and outdoor use on floors and walls for ceramic and porcelain tiles. Preparation of sub-layer: For better results we must follow the rules below. The surfaces that the mixture will be placed on different walls or floors have to be well clean from dust, oil, polyurethane, or other material. If the substrates are rusted and destroyed must be carefully cleaned and removed from any other materials. We have to be careful that the area where the mixture is done (bucket), is made by a product which can be easily cleaned. During the preparation of the product, you must be sure that the metals of the spatula or buckets do not have any signs of rust that can affect negatively the chemical reaction and the color of the adhesive. We also have to be careful that the containers we will use are easy to clean and they will always be clean before use. At the end of day, we suggest you clean all the instruments used, because the miss cleaning of the instruments can conclude in bad colors on your final construction. The chemical reactions of the materials can affect the soldering ( in alkali trestle we use primer). The substrate must be a smooth surface, so the use of overdose adhesive is not needed. With this method, we will cover all the anomalies of the floor or wall. Do not forget that all the construction products are producing for the best possible quality, save time and perfect essential result. Preparation of Mixture: We mix 25kg ALFAKOL 3* with roughly 8 liters clean water in a clean container, always with electric mixer until we achieve a smooth uniform paste. Wait for 5 minutes and mix again. The adhesive is ready for use. ALFAKOL 3* has life in the bucket for approximately 4 hours when we mix every 1 hour. We do not add water, simply we mix with an electrical mixer. Most minimum time for light use 24 hours and the time of final use 14 days. 6

12 Usage Instructions: 1. We clean and fix the old sub layer. 2. Afterwards we should clean the surface by any chance oils, dust, remains of colour etc. 3. The wall does not need any sprinkling either the tiles need any wash. This saves time and money. 4. We stretch out the adhesive with toothed spatula as long as it needs we work for minutes depending on temperature. At temperatures above 23ºC the open time of application decreases and at temperatures under 23ºC, the open time of application increases. 5. We cover the decorated surface with tiles which abstain from each other 2-3 thousandth for expansion and contraction. 6. In order to cover 1 sq.m. of tiles we need 2-5 Kg ALFAKOL 3*. For other uses it depends on type and surface that it will be placed. 7

13 Technical characteristics (typical numbers): Alfakol 3* Product definition: Type: Powder Colour: White and grey Specific Gravity: 1.35 kg/lt Composition of dry materials: 100% Storage: 9 months in a dry place, closed sealed sack Package & Weight:: Bags of 10kg & 25kg Toxicity / Inflammability: No Elements of use: Composition of Mixture: Thick Water Requirements: 25kg Powder roughly 8 Liters Water Specific gravity of mixture: 1.62 kg/lt PH Mixture: 13 Self life in bucket: 4 Hours/ mix every 1 hour Application Temperature: 5 ºC ºC Growthing Time: 24 Hours Time for Final use: 14 Days Consumption: 2-5kg/m² Depending on use Strengths: Humidity: Excellent Acids-Alkali: Poor Temperature: -30ºC until+90ºc Declaration tests for marked CE: C2TE Determination of open time: 0,6 Ν/mm² Initial Adherence: 2,1 Ν/mm² Adherence after heat ageing: 1,2 Ν/mm² Adherence after immersion in water: 1,0 Ν/mm² Adherence after freezing-defrosting cycles: 1,1 Ν/mm² Slip determination in vertical wall: 0,5 mm Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, however can be effected from others. The users of the product have the responsibility to follow correct processes of health and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information, please contact with AVRAAM PITTAKIS and SONS LTD. 8

14 Declaration of Performance: No.: CPR004-01/07/ Unique identification code of the product-type: ALFAKOL 3* Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: C2TE - Superstrength, acrylic, waterproof, cementitious tile adhesive for indoor & outdoor use on floors & walls. 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5.Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6.System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 3 7.In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ A notified testing laboratory, the APPLUS, LGAI TECHNOLOGICAL CENTER, S.A, NB 0370, has performed the determination of the product-type on the basis of Initial Type Testing (ITT) under system 3 and issued the test report Nº 08/ In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9.Declared performance Essential characteristics Reaction to fire Extended open time (30 min) Initial adhesion strength Adhesion Strength after heat ageing Adhesion Strength after water immersion Adhesion Strength after freeze - thaw cycles Improved slip resistance Classification C2ΤΕ Performance Class Α1 0,5 Ν/mm² 1 Ν/mm² 1 Ν/mm² 1 Ν/mm² 1 Ν/mm² 0,5 mm Harmonised Technical Specification ΕΝ 12004: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/2013 9

15 10

16 ALFAKOL 6* Use-Examples of enforcements: Alfakol 6* C2TE-S1 Super strength, Flexible, Acrilic, Waterproof With null vertical slipping and extensive appliance time, flexibility (category 1), for indoor and outdoor use on floors, walls, for ceramic with low absorption, pools, floor heating, plaster board, cement board and glass bricks. Preparation of sub layer: For better results we must follow the rules below. The surfaces that the mixture will be placed on different walls or floors have to be well clean from dust, oil, polyurethane, or other material. If the substrates are rusted and destroyed must be carefully cleaned and removed from any other materials. We have to be careful that the area where the mixture is done (bucket), is made by a product which can be easily cleaned. During the preparation of the product, you must be sure that the metals of the spatula or buckets do not have any signs of rust that can affect negatively the chemical reaction and the color of the adhesive. We also have to be careful that the containers we will use are easy to clean and they will always be clean before use. At the end of day, we suggest you clean all the instruments used, because the miss cleaning of the instruments can conclude in bad colors on your final construction. The chemical reactions of the materials can affect the soldering ( in alkali trestle we use primer). The substrate must be a smooth surface, so the use of overdose adhesive is not needed. With this method, we will cover all the anomalies of the floor or wall. Do not forget that all the construction products are producing for the best possible quality, save time and perfect essential result. Preparation of Mixture: We mix 25kg ALFAKOL 6* with roughly 8 liters clean water in a clean container, always with electric stirrer until we achieve uniform pastry. Wait for 5 minutes and mix again. The material is ready for use. ALFAKOL 6* has life in the container for approximately 4 hours when we stir every 1 hour. We do not add water, simply we stir with an electric blender. Most minimum time for light use 24 hours and the time of final use 14 days. 11

17 Directives of Use: 1. We clean and fix the rotten sublayer. 2. Afterwards we should clean the surface by any chance oils, dust, remains of colour etc. 3. The wall does not need any sprinkling either the tiles need any wash. This saves time and money. 4. We stretch out the adhesive with toothed spatula as long as it needs we work for minutes depending on temperature. At temperatures above 23ºC the open time of application decreases and at temperatures under 23ºC, the open time of application increases. 5. We cover the decorated surface with tiles which abstain from each other 2-3 thousandth for expansion and contraction. 6. In order to cover 1 sq.m. of tiles we need 2-5 Kg ALFAKOL 6*. For other uses it depends on type and surface that it will be placed. 12

18 Technical characteristics: (Typical Numbers) Alfakol 6* Product definition: Type: Powder Colour: White and grey Specific Gravity: 1.35 kg/lt Composition of dry materials: 100% Storage: 9 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use: Composition of Mixture: Thick Water Requirements: 25kg Powder roughly 8 Liters Water Specific gravity of mixture: 1.62 kg/lt PH Mixture: 13 Self life in bucket: 4 Hours/ mix every 1 hour Application Temperature: 5 ºC ºC Growthing Time: 24 Hours Time for Final use: 48 Days Consumption: 2-5kg/m² Depending on use Strengths: Humidity: Excellent Acids-Alkali: Poor Temperature: -30ºC until+90ºc Declaration tests for marked CE: C2TE-S1 Determination of open time (30 mins): 0,8 Ν/mm² Initial Adhesion strength: 2,1 Ν/mm² Adhesion strength after heat ageing: 1,9 Ν/mm² Adhesion strength after immersion in water: 1,5 Ν/mm² Adhesion strength after freezing-defrosting cycles: 2,0 Ν/mm² Slip determination in vertical wall: 0,3 mm Flexibility definition: 3,3 mm Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 13

19 Declaration of Performance: No.: CPR084-01/07/ Unique identification code of the product-type: ALFAKOL 6* Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: C2TE - S1 - Super strength, flexible, acrylic, waterproof, cementitious tile adhesive for indoor & outdoor use on floors & walls. 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 3 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ A notified testing laboratory, the APPLUS, LGAI TECHNOLOGICAL CENTER, S.A, NB 0370, has performed the determination of the product-type on the basis of Initial Type Testing (ITT) under system 3 and issued the test report Nº 08/ In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Extended open time (30 min) Initial adhesion strength Adhesion Strength after heat ageing Adhesion Strength after water immersion Adhesion Strength after freeze - thaw cycles Improved slip resistance Deformability Classification C2ΤΕ - S1 Performance Class Α1 0,5 Ν/mm² 1 Ν/mm² 1 Ν/mm² 1 Ν/mm² 1 Ν/mm² 0,5 mm 2,5mm & 5mm Harmonised Technical Specification ΕΝ 12004: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

20 15

21 ALFAKOL 11* Use-Examples of enforcements: Alfakol 11* C2TE-S1 Super strength, Flexible, Acrilic, Waterproof With null vertical slipping and extensive appliance time, flexibility (category 1), for indoor and outdoor use on floors, walls, for ceramic with low absorption, ceramic on mosaics, stones, pools, granites, floor heating, plaster board, cement board and glass bricks. Preparation of sub layer: For better results we must follow the rules below. The surfaces that the mixture will be placed on different walls or floors have to be well clean from dust, oil, polyurethane, or other material. If the substrates are rusted and destroyed must be carefully cleaned and removed from any other materials. We have to be careful that the area where the mixture is done (bucket), is made by a product which can be easily cleaned. During the preparation of the product, you must be sure that the metals of the spatula or buckets do not have any signs of rust that can affect negatively the chemical reaction and the color of the adhesive. We also have to be careful that the containers we will use are easy to clean and they will always be clean before use. At the end of day, we suggest you clean all the instruments used, because the miss cleaning of the instruments can conclude in bad colors on your final construction. The chemical reactions of the materials can affect the soldering (in alkali trestle we use primer). The substrate must be a smooth surface, so the use of overdose adhesive is not needed. With this method, we will cover all the anomalies of the floor or wall. Do not forget that all the construction products are producing for the best possible quality, save time and perfect essential result. Preparation of Mixture: We mix 25kg ALFAKOL 11* with roughly 8 liters clean water in a clean container, always with electric stirrer until we achieve uniform pastry. Wait for 5 minutes and mix again. The material is ready for use. ALFAKOL 6* has life in the container for approximately 4 hours when we stir every 1 hour. We do not add water, simply we stir 16

22 with an electric blender. Most minimum time for light use 24 hours and the time of final use 14 days. Directives of Use: 1. We clean and fix the rotten sublayer. 2. Afterwards we should clean the surface by any chance oils, dust, remains of colour etc. 3. The wall does not need any sprinkling either the tiles need any wash. This saves time and money. 4. We stretch out the adhesive with toothed spatula as long as it needs we work for minutes depending on temperature. At temperatures above 23ºC the open time of application decreases and at temperatures under 23ºC, the open time of application increases. 5. We cover the decorated surface with tiles which abstain from each other 2-3 thousandth for expansion and contraction. 6. In order to cover 1 sq.m. of tiles we need 2-5 Kg ALFAKOL 11*. For other uses it depends on type and surface that it will be placed. 17

23 Technical characteristics: Alfakol 11* Product definition: Type: Powder Colour: White, grey and yellow Specific Gravity: 1.35 kg/lt Composition of dry materials: 100% Storage: 9 months in a dry place, closed sealed sack Package & Weight:: Bags of 25kg Toxicity / Inflammability: No Elements of use: Composition of Mixture: Thick Water Requirements: 25kg Powder roughly 8 Liters Water Specific gravity of mixture: 1.62 kg/lt PH Mixture: 13 Self life in bucket: 4 Hours/ mix every 1 hour Application Temperature: 5 ºC ºC Growthing Time: 48 Hours Time for Final use: 14 Days Consumption: 2-5kg/m² Depending on use Strengths: Humidity: Acids-Alkali: Temperature: Declaration tests for marked CE: Determination of open time (30 mins): Initial Adhesion strength: Adhesion strength after heat ageing: Adhesion strength after immersion in water: Adhesion strength after freezing-defrosting cycles: Slip determination in vertical wall: Flexibility definition: Excellent Poor -30ºC until+90ºc C2TE-S1 0,8 Ν/mm² 2,7 Ν/mm² 2,4 Ν/mm² 1,8 Ν/mm² 2,3 Ν/mm² 0,3 mm 3,6 mm Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 18

24 Declaration of Performance: No.: CPR007-01/07/ Unique identification code of the product-type: ALFAKOL 11* Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: C2TE - S1 - Super strength, flexible, acrylic, waterproof, cementitious tile adhesive for indoor & outdoor use on floors & walls. 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 3 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ A notified testing laboratory, the APPLUS, LGAI TECHNOLOGICAL CENTER, S.A, NB 0370, has performed the determination of the product-type on the basis of Initial Type Testing (ITT) under system 3 and issued the test report Nº 08/ In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Extended open time (30 min) Initial adhesion strength Adhesion Strength after heat ageing Adhesion Strength after water immersion Adhesion Strength after freeze - thaw cycles Improved slip resistance Deformability Classification C2ΤΕ - S1 Performance Class Α1 0,5 Ν/mm² 1 Ν/mm² 1 Ν/mm² 1 Ν/mm² 1 Ν/mm² 0,5 mm 2,5mm & 5mm Harmonised Technical Specification ΕΝ 12004: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

25 20

26 Use-Examples of enforcements: ALFAKOL 15* Alfakol 15* C2TE-S2 Super strength, Flexible, Acrilic, Waterproof with null vertical slipping and extensive appliance time, flexibility (category 2), for indoor and outdoor use on floors, walls, for ceramic with low absorption granité, granites, stones, ceramic on ceramic, glass mosaics, pools, floor heating, polystyrenes, cement board and glass bricks. For better results we must follow the rules below. The surfaces that the mixture will be placed on different walls or floors have to be well clean from dust, oil, polyurethane, or other material. If the substrates are rusted and destroyed must be carefully cleaned and removed from any other materials. We have to be careful that the area where the mixture is done (bucket), is made by a product which can be easily cleaned. During the preparation of the product, you must be sure that the metals of the spatula or buckets do not have any signs of rust that can affect negatively the chemical reaction and the color of the adhesive. We also have to be careful that the containers we will use are easy to clean and they will always be clean before use. At the end of day, we suggest you clean all the instruments used, because the miss cleaning of the instruments can conclude in bad colors on your final construction. The chemical reactions of the materials can affect the soldering (in alkali trestle we use primer). The substrate must be a smooth surface, so the use of overdose adhesive is not needed. With this method, we will cover all the anomalies of the floor or wall. Do not forget that all the construction products are producing for the best possible quality, save time and perfect essential result. Preparation of Mixture: We mix 25kg ALFAKOL 15* with roughly 8 liters clean water in a clean container, always with electric stirrer until we achieve uniform pastry. Wait for 5 minutes and mix again. The material is ready for use. ALFAKOL 15* has life in the container for approximately 4 hours when we stir every 1 hour. We do not add water, simply we stir with an electric blender. Most minimum time for light use 48 hours and the time of final use 14 days. 21

27 Directives of Use: 1. We clean and fix the rotten sublayer. 2. Afterwards we should clean the surface by any chance oils, dust, remains of colour etc. 3. The wall does not need any sprinkling either the tiles need any wash. This saves time and money. 4. We stretch out the adhesive with toothed spatula as long as it needs we work for minutes depending on temperature. At temperatures above 23ºC the open time of application decreases and at temperatures under 23ºC, the open time of application increases. 5. We cover the decorated surface with tiles which abstain from each other 2-3 thousandth for expansion and contraction. 6. In order to cover 1 sq.m. of tiles we need 2-5 Kg ALFAKOL 15*. For other uses it depends on type and surface that it will be placed. 22

28 Technical characteristics (typical numbers): Alfakol 15* Product definition: Type: Powder Colour: White and grey Specific Gravity: 1.35 kg/lt Composition of dry materials: 100% Storage: 9 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use: Composition of Mixture: Thick Water Requirements: 25kg Powder roughly 8 Liters Water Specific gravity of mixture: 1.62 kg/lt PH Mixture: 13 Self life in bucket: 4 Hours/ mix every 1 hour Application Temperature: 5 ºC ºC Growthing Time: 48 Hours Time for Final use: 14 Days Consumption: 2-5kg/m² Depending on use Strengths: Humidity: Acids-Alkali: Temperature: Declaration tests for marked CE: Determination of open time (30 mins): Initial Adhesion strength: Adhesion strength after heat ageing: Adhesion strength after immersion in water: Adhesion strength after freezing-defrosting cycles: Slip determination in vertical wall: Flexibility definition: Excellent Poor -30ºC until+90ºc C2TE-S2 1.0 Ν/mm² 3,1 Ν/mm² 2.7 Ν/mm² 2.1 Ν/mm² 2.5 Ν/mm² 0.2 mm 5.8 mm Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 23

29 Declaration of Performance: No.: CPR074-01/07/ Unique identification code of the product-type: ALFAKOL 15* Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: C2TE - S2 - - Super strength, flexible, acrylic, waterproof, cementitious tile adhesive for indoor & outdoor use on floors & walls. 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 3 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ A notified testing laboratory, the APPLUS, LGAI TECHNOLOGICAL CENTER, S.A, NB 0370, has performed the determination of the product-type on the basis of Initial Type Testing (ITT) under system 3 and issued the test report Nº 08/ In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Extended open time (30 min) Initial adhesion strength Adhesion Strength after heat ageing Adhesion Strength after water immersion Adhesion Strength after freeze - thaw cycles Improved slip resistance Deformability Classification C2ΤΕ - S2 Performance Class Α1 0,5 Ν/mm² 1 Ν/mm² 1 Ν/mm² 1 Ν/mm² 1 Ν/mm² 0,5 mm 5mm Harmonised Technical Specification ΕΝ 12004: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

30 25

31 Use-Examples of enforcements: ALFAKOL 18* Alfakol 18* C2TE-S2 Super strength, Flexible, Acrilic, Waterproof with null vertical slipping and extensive appliance time, flexibility (category 2), for indoor and outdoor use on floors, walls, for ceramic with low absorption granité, granites, stones, ceramic on ceramic, glass mosaics, pools, floor heating, polystyrenes, cement board and glass bricks. For better results we must follow the rules below. The surfaces that the mixture will be placed on different walls or floors have to be well clean from dust, oil, polyurethane, or other material. If the substrates are rusted and destroyed must be carefully cleaned and removed from any other materials. We have to be careful that the area where the mixture is done (bucket), is made by a product which can be easily cleaned. During the preparation of the product, you must be sure that the metals of the spatula or buckets do not have any signs of rust that can affect negatively the chemical reaction and the color of the adhesive. We also have to be careful that the containers we will use are easy to clean and they will always be clean before use. At the end of day, we suggest you clean all the instruments used, because the miss cleaning of the instruments can conclude in bad colors on your final construction. The chemical reactions of the materials can affect the soldering (in alkali trestle we use primer). The substrate must be a smooth surface, so the use of overdose adhesive is not needed. With this method, we will cover all the anomalies of the floor or wall. Do not forget that all the construction products are producing for the best possible quality, save time and perfect essential result. Preparation of Mixture: We mix 25kg ALFAKOL 18* with roughly 8 liters clean water in a clean container, always with electric stirrer until we achieve uniform pastry. Wait for 5 minutes and mix again. The material is ready for use. ALFAKOL 18* has life in the container for approximately 4 hours when we stir every 1 hour. We do not add water, simply we stir 26

32 with an electric blender. Most minimum time for light use 24 hours and the time of final use 14 days. Directives of Use: 1. We clean and fix the rotten sublayer. 2. Afterwards we should clean the surface by any chance oils, dust, remains of colour etc. 3. The wall does not need any sprinkling either the tiles need any wash. This saves time and money. 4. We stretch out the adhesive with toothed spatula as long as it needs we work for minutes depending on temperature. At temperatures above 23ºC the open time of application decreases and at temperatures under 23ºC, the open time of application increases. 5. We cover the decorated surface with tiles which abstain from each other 2-3 thousandth for expansion and contraction. 6. In order to cover 1 sq.m. of tiles we need 2-5 Kg ALFAKOL 18*. For other uses it depends on type and surface that it will be placed. 27

33 Technical characteristics (typical numbers): Alfakol 18* Product definition: Type: Powder Colour: White and grey Specific Gravity: 1.35 kg/lt Composition of dry materials: 100% Storage: 9 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use: Composition of Mixture: Thick Water Requirements: 25kg Powder roughly 8 Liters Water Specific gravity of mixture: 1.62 kg/lt PH Mixture: 13 Self life in bucket: 4 Hours/ mix every 1 hour Application Temperature: 5 ºC ºC Growthing Time: 24 Hours Time for Final use: 14 Days Consumption: 2-5kg/m² Depending on use Strengths: Humidity: Excellent Acids-Alkali: Poor Temperature: -30ºC until+90ºc Declaration tests for marked CE: C2TE-S2 Determination of open time (30 mins): 1.4 Ν/mm² Initial Adhesion strength: 3.5 Ν/mm² Adhesion strength after heat ageing: 2.9 Ν/mm² Adhesion strength after immersion in water: 2.3 Ν/mm² Adhesion strength after freezing-defrosting 2.7 Ν/mm² cycles: Slip determination in vertical wall: 0.3 mm Flexibility definition: 9.4 mm Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 28

34 Declaration of Performance: No.: CPR118-01/07/ Unique identification code of the product-type: ALFAKOL 18* Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: C2TE - S2 - Super strength, flexible (category 2), acrylic, waterproof, cementitious tile adhesive for indoor & outdoor use on floors & walls. 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 3 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ A notified testing laboratory, the APPLUS, LGAI TECHNOLOGICAL CENTER, S.A, NB 0370, has performed the determination of the product-type on the basis of Initial Type Testing (ITT) under system 3 and issued the test report Nº 08/ In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Extended open time (30 min) Initial adhesion strength Adhesion Strength after heat ageing Adhesion Strength after water immersion Adhesion Strength after freeze - thaw cycles Improved slip resistance Deformability Classification C2ΤΕ - S2 Performance Class Α1 0,5 Ν/mm² 1 Ν/mm² 1 Ν/mm² 1 Ν/mm² 1 Ν/mm² 0,5 mm 5mm Harmonised Technical Specification ΕΝ 12004: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

35 30

36 Use-Examples of enforcements: ALFAKOL 24* Alfakol 24* C2FTE-S2 Super strength, Flexible, Acrilic, Waterproof, Fast Setting with null vertical slipping and extensive appliance time, flexibility (category 2), for indoor and outdoor use on floors, walls, for ceramic with low absorption granité, granites, stones, ceramic on ceramic, glass mosaics, pools, floor heating, polystyrenes, cement board and glass bricks. Preparation of sub layer: For better results we must follow the rules below. The surfaces that the mixture will be placed on different walls or floors have to be well clean from dust, oil, polyurethane, or other material. If the substrates are rusted and destroyed must be carefully cleaned and removed from any other materials. We have to be careful that the area where the mixture is done (bucket), is made by a product which can be easily cleaned. During the preparation of the product, you must be sure that the metals of the spatula or buckets do not have any signs of rust that can affect negatively the chemical reaction and the color of the adhesive. We also have to be careful that the containers we will use are easy to clean and they will always be clean before use. At the end of day, we suggest you clean all the instruments used, because the miss cleaning of the instruments can conclude in bad colors on your final construction. The chemical reactions of the materials can affect the soldering (in alkali trestle we use primer). The substrate must be a smooth surface, so the use of overdose adhesive is not needed. With this method, we will cover all the anomalies of the floor or wall. Do not forget that all the construction products are producing for the best possible quality, save time and perfect essential result. Preparation of Mixture: We mix 25kg ALFAKOL 24* with roughly 6-7 liters clean water in a clean container, always with electric stirrer until we achieve uniform pastry. Wait for 5 minutes and mix again. The material is ready for use. ALFAKOL 24* has life in the container for approximately 2 hours when we stir every 1/2 hour. We do not add water, simply we stir 31

37 with an electric blender. Most minimum time for light use 6 hours and the time of final use 24 hours. Directives of Use: 1. We clean and fix the rotten sublayer. 2. Afterwards we should clean the surface by any chance oils, dust, remains of colour etc. 3. The wall does not need any sprinkling either the tiles need any wash. This saves time and money. 4. We stretch out the adhesive with toothed spatula as long as it needs we work for 10 minutes depending on temperature. At temperatures above 23ºC the open time of application decreases and at temperatures under 23ºC, the open time of application increases. 5. We cover the decorated surface with tiles which abstain from each other 2-3 thousandth for expansion and contraction. 6. In order to cover 1 sq.m. Of tiles we need 2-5 Kg ALFAKOL 24*. For other uses it depends on type and surface that it will be placed. 32

38 Technical characteristics typical numbers): Alfakol 24* Product definition: Type: Powder Colour: White and grey Specific Gravity: 1.35 kg/lt Composition of dry materials: 100% Storage: 9 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use: Composition of Mixture: Thick Water Requirements: 25kg Powder roughly 6-7 Liters Water Specific gravity of mixture: 1.62 kg/lt PH Mixture: 13 Self life in bucket: 2 Hours/ mix every 1/2 hour Application Temperature: 5 ºC ºC Growthing Time: 6 Hours Time for Final use: 1 Day Consumption: 2-5kg/m² Depending on use Strengths: Humidity: Acids-Alkali: Temperature: Declaration tests for marked CE: Determination of open time: Initial Adherence: Adherence after ageing with HCAT: Adherence after immersion in water: Adherence after freezing-defrosting cycles: Slip determination in vertical wall: Flexibility definition: Excellent Poor -30ºC until+90ºc C2FTE-S2 0,6 Ν/mm² 3,1 Ν/mm² 1,9 Ν/mm² 1,2 Ν/mm² 1,3 Ν/mm² 0,2 mm 9,2 mm Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 33

39 Declaration of Performance: No.: CPR199-01/07/ Unique identification code of the product-type: ALFAKOL 24* Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: C2FTE - S2 - Super strength, flexible (category 2), acrylic, waterproof, fast - setting, cementitious tile adhesive for indoor & outdoor use on floors & walls. 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 3 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ A notified testing laboratory, the APPLUS, LGAI TECHNOLOGICAL CENTER, S.A, NB 0370, has performed the determination of the product-type on the basis of Initial Type Testing (ITT) under system 3 and issued the test report Nº 08/ In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Extended open time (30 min) Adhesion Strength after 6 hours Initial adhesion strength Adhesion Strength after heat ageing Adhesion Strength after water immersion Adhesion Strength after freeze - thaw cycles Improved slip resistance Deformability Classification C2FΤΕ - S2 Performance Class Α1 0,5 Ν/mm² 0,5 Ν/mm² 1 Ν/mm² 1 Ν/mm² 1 Ν/mm² 1 Ν/mm² 0,5 mm 5mm Harmonised Technical Specification ΕΝ 12004: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

40 35

41 ALFATHERM Base Coat ALFATHERM Base Coat is a cement mortar of one component based on high quality cement, selected fine grained sand, special additives and fibers for bonding and levelling thermal insulation panels on bricks, plastered surfaces, even on concrete walls. Also ideal for bonding and levelling reinforcing mesh on thermal insulation panels. It can also be used for plaster boards & cement boards as a coating, or on various textured plaster surfaces. Instructions for use: Surface preparation: The substrate must be flat, strong and clean from dust or oils. In case that the substrate is not flat, it is recommended to even out variations in surface level, before ALPHA THERM application. For better adhesion the surfaces should be lightly moistened with little water. Mixing: In a clean bucket, add 6 7 Litres clean water and 25kg ALAFATHERM BASE COAT. Mixing with a concrete machine or with a low speed electrical mixer until a smooth homogeneous paste is obtained. Leave the mixture to stand for about 5 minutes and mix again. Application Steps For maximum results, the following steps described below are recommended: Step 1: For bonding thermal insulation panels on masonry: choose one of the 2 methods of 1(i) or 1(ii) depending on your existing substrate. 1(i) For substrate without any raised areas or indentations Full Surface Coating Method: directly on substrate apply a thin layer of Alfatherm Base Coat with the flat side of the trowel. Give thickness to the application by adding the same coating with the notched side of the trowel and install the thermal insulation panels by applying a strong pressure over the panels in order to adhere well with the substrate. 1(ii) For substrate with little raised areas or indentations Peripheral Strip & Middle Points Coating Method: For polystyrene panels: apply Alfatherm Base Coat with a trowel at a 4-5 cm strip along the board edges and at 3 spots in the middle with a diameter of about 15cm. Then place the panels on the masonry by applying a pressure over them in order to adhere well with the substrate. For mineral wool panels: in order to obtain an adequate bonding, firstly a kind of primer should be applied with the flat side of the trowel, filling in that way the pores of mineral wool panels. After priming, follow the application process of Alfatherm Base Coat (as described above in method 1 (ii) for polystyrene panels). In all cases of Method 1(ii), the mortar should cover at least 40% of the board s surface. 36

42 Step 2: For bonding fiberglass mesh on thermal insulation panels: Directly on thermal insulation panel, apply a thin layer of Alfatherm Base Coat with the flat side of the trowel. Give to the application the desire thickness by adding the same coating with a notched trowel of 5mm and embed the fiberglass mesh. Applying pressure to the mess with a flat trowel and leave the material to adequate dry before proceeding to step 3. Step 3: Surface preparation prior the application of finish coat: follow one of the 2 methods below 3(i) or 3(ii) depending on your choice for the finish coat (elastomeric paint or acrylic textured plaster) 3(i) Surface preparation when finish coat is elastomeric paint: On the surface, apply 2 layers of Alfatherm Top Coat (about 2mm). Rub the surface when it is still fresh and let the material be sufficiently dried. Now, the surface is flat and smooth. Then prime the surface with Alfaliq Primer and let it to dry completely. 3(ii) Surface preparation when finish coat is acrylic textured plaster: Surface preparation when finish coat is acrylic textured plaster: On the surface, apply 1 layer of Alfatherm Base Coat (about 2mm) and let the material be sufficiently dried. Now, the surface is flat and smooth. Then prime the surface with Alfaliq Grafit Primer and let it to dry completely. Step 4: Finish Coat: The options is Elastomeric Paint or Acrylic Textured Plaster. Recommendations Do not bond thermal insulation panels with ALFATHERM BASE COAT in weathered and damaged plasters. All flimsy areas and layers with low mechanical resistance should be preliminary removed prior the application of ALFATHERM. Special attention should be paid to humidity issues. Prior the installation of thermal insulation panels, any surfaces which are subject to high level of humidity penetration, should be insulated with the Alfa Water Seal, at a height of 30-40cm above ground level. Weather Conditions: Use at temperatures between +5 o C and +40 o C. Too high or too low temperatures, it might cause a negative reaction to the product. Storage: Store out of direct sunlight, clear of the ground on pallets, protect from rainfall. Avoid excessive compaction. Shelf life is 8 months when stored as above. 37

43 Technical characteristics (typical values): ALFATHERM Base Coat Product Identity Consistency: Powder Colour: Grey/White Dry Solid content (%): 100% Storage: 8 months in a dry place in original unopened packaging Granulometry: mm Bulk Density: 1250 kg/m 3 Package & Weight: Bags of 25kg Toxicity / Inflammability: NO Application data Consistency of mix: Paste Mix Ratio: 25kg Powder with 6-7 Liters Water Wet density: 1.8 kg/lt Application temperature range: +5 ºC ºC pη of the mix: >10 Pot Life: 3 hours Open time: 30 min Consumption: Bonding insulating panels with a uniform layer on 5-6 kg/m² the back of the panel Smoothing and Levelling thermal insulating panels 3 4 kg/m² per 2 mm thickness (recommended thickness 4mm in two coats) Waiting time before finishing: 7 days for summer and 14 days for winter period Final Performances: Adhesion Strength after 28 days according to ΕΝ N/mm² Flexural Strength after 28 days according to ΕΝ N/mm² Compressive Strength after 28 days according to ΕΝ N/mm² Water Absorption Class w2 (c<0.2 kg/m2.min0.5) Thermal Conductivity 0.9 W/m.K Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information, contact with AVRAAM PITTAKIS and SONS LTD. 38

44 Declaration of Performance: No.: AP133 CPR - 01/07/ Unique identification code of the product-type: ALFATHERM Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7.In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance >1.5 Ν/mm 2 - FΡ: B CSIV Water Absorption W2 Water Vapour permeability coefficient μ 15 Dry Bulk Density 1250 kg/m 3 Harmonised Technical Specification ΕΝ 998-1: 2010 Thermal Conductivity, λ 10, dry 0.9 W/m K for Ρ=50% Durability (against freeze/thaw) Evaluation based on provisions valid in the intended place of use of the mortar. 10.The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

45 ALFA-THERM Thick ALFA-THERM Thick granulated, is one-component, fibre reinforced, ready mixed mortar based on high quality cement, non-absorbent sand and special. ALPHA THERM thick granulated can be used as a base coat on thermal insulation panels with embedded mesh (see instructions for preparation and application of ALFA-THERM fine granulated), for protecting XPS & EPS panels. Instructions for use: Surface preparation: The surface to be plastered must be clean from dust or oils. For better adhesion the surface should be lightly moistened with little water. Mixing: In a clean bucket, add 25kg ALFA THERM thick granulated to 6 7 L water. Mix in a concrete machine or with a low speed electric mixer until a homogenous paste is obtained. Leave the mixture to stand for about 5 minutes and mix again. Application: ALFA-THERM thick granulated is applied on thermal insulation panels plastered with ALFATHERM fine granulated. Step 1: With a flat trowel apply a uniform coat ALFATHERM fine granulated over the panels. Step 2: Apply ALFATHERM fine granulated with a 5 mm notched trowel and insert the fiberglass mesh. With a flat trowel press the mesh into the fresh mortar. Step 3: Apply ALFATHERM thick granulated when the previous layer has been set. Step 4: a) With a flat trowel apply a uniform coat ALFATHERM fine granulated (2 mm). When the smoothing compound has hardened and cured paint the surface. b) Directly on ALFATHERM thick granulated apply an acrylic paste-plaster. Weather Conditions: Use at temperatures between +5 o C and +40 o C. Too high or too low temperatures, it might cause a negative reaction to the product. Storage: Store out of direct sunlight, clear of the ground on pallets, protect from rainfall. Avoid excessive compaction. Shelf life is 8 months when stored as above. 40

46 Technical characteristics (typical values): ALFA THERM Thick Granulated Product Identity Consistency: Powder Colour: Grey/White Dry Solid content (%): 100% Storage: 8months in a dry place in original unopened packaging Granulometry: mm Bulk Density: 1470 kg/m 3 Package & Weight: Bags of 25kg Toxicity / Inflammability: NO Application data Consistency of mix: Paste Mix Ratio: 25kg Powder with 6-7 Liters Water Wet density: 1.63 kg/lt Application temperature range: +5 ºC ºC pη of the mix: >10 Pot Life: 3 hours Consumption: 5-6 kg/m² per 3-4mm of thickness Waiting time before finishing: 7 days for summer and 14 days for winter period Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information, contact with AVRAAM PITTAKIS and SONS LTD. 41

47 ALFATHERM Top Coat ALFATHERM Top Coat is a cement mortar of one component based on high quality cement, selected fine grained sand, special additives and fibers for levelling the existing integrated fiberglass mesh on thermal insulation panels, on cement boards and gypsum boards. Instructions for use: Surface preparation: The substrate must be flat, strong and clean from dust or oils.. For better adhesion the surfaces should be lightly moistened with little water. Preparing the mixing: In a clean bucket, add 6 7 Litres clean water and 25kg ALAFATHERM TOP COAT. Mixing with a concrete machine or with a low speed electrical mixer until a smooth homogeneous paste is obtained. Leave the mixture to stand for about 5 minutes and mix again. Application Steps For maximum results, the following steps described below are recommended: Step 1: For bonding thermal insulation panels on masonry: choose one of the 2 methods of 1(i) or 1(ii) depending on your existing substrate. 1(i) For substrate without any raised areas or indentations Full Surface Coating Method: directly on substrate apply a thin layer of Alfatherm Base Coat with the flat side of the trowel. Give thickness to the application by adding the same coating with the notched side of the trowel and install the thermal insulation panels by applying a strong pressure over the panels in order to adhere well with the substrate. 1(ii) For substrate with little raised areas or indentations Peripheral Strip & Middle Points Coating Method: For polystyrene panels: apply Alfatherm Base Coat with a trowel at a 4-5 cm strip along the board edges and at 3 spots in the middle with a diameter of about 15cm. Then place the panels on the masonry by applying a pressure over them in order to adhere well with the substrate. For mineral wool panels: in order to obtain an adequate bonding, firstly a kind of primer should be applied with the flat side of the trowel, filling in that way the pores of mineral wool panels. After priming, follow the application process of Alfatherm Base Coat (as described above in method 1 (ii) for polystyrene panels). In all cases of Method 1(ii), the mortar should cover at least 40% of the board s surface. 42

48 Step 2: For bonding fiberglass mesh on thermal insulation panels: Directly on thermal insulation panel, apply a thin layer of Alfatherm Base Coat with the flat side of the trowel. Give to the application the desire thickness by adding the same coating with a notched trowel of 5mm and embed the fiberglass mesh. Applying pressure to the mess with a flat trowel and leave the material to adequate dry before proceeding to step 3. Step 3: Surface preparation prior the application of finish coat: follow one of the 2 methods below 3(i) or 3(ii) depending on your choice for the finish coat (elastomeric paint or acrylic textured plaster) 3(i) Surface preparation when finish coat is elastomeric paint: On the surface, apply 2 layers of Alfatherm Top Coat (about 2mm). Rub the surface when it is still fresh and let the material be sufficiently dried. Now, the surface is flat and smooth. Then prime the surface with Alfaliq Primer and let it to dry completely. 3(ii) Surface preparation when finish coat is acrylic textured plaster: On the surface, apply 1 layer of Alfatherm Base Coat (about 2mm) and let the material be sufficiently dried. Now, the surface is flat and smooth. Then prime the surface with Alfaliq Grafit Primer and let it to dry completely. Step 4: Finish Coat: The options is Elastomeric Paint or Acrylic Textured Plaster. Weather Conditions: Use at temperatures between +5 o C and +40 o C. Too high or too low temperatures, it might cause a negative reaction to the product. Storage: Store out of direct sunlight, clear of the ground on pallets, protect from rainfall. Avoid excessive compaction. Shelf life is 8 months when stored as above. 43

49 Technical characteristics (typical values): ALFATHERM Top Coat Product Identity Consistency: Powder Colour: Grey/White Dry Solid content (%): 100% Storage: 8 months in a dry place in original unopened packaging Granulometry: mm Bulk Density: 1250 kg/m 3 Weight/package 25kg/paper-bag Toxicity/Inflammability: NO Application data Consistency of mix: Paste Mix Ratio: 25kg Powder with 6-7 Liters Water Wet density: 1.8 kg/m³ Application temperature range: +5 ºC ºC pη of the mix: >10 Pot Life in 22 o C: About 3 hours Open time: 30 min Consumption for Smoothing and Levelling 3 4 kg/m² of 2 mm thickness / layer (recommended layers: 2) Waiting time before finishing: 7 days for summer and 14 days for winter period Strength results after ageing: Adhesion Strength after 28 days according to ΕΝ N/mm² Flexural Strength after 28 days according to ΕΝ N/mm² Compressive Resistance after 28 days according to ΕΝ N/mm² Water absorption Category w2 (c<0.2 kg/m2.min0.5) Thermal Conductivity 0.9 W/m.K given table value Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information, contact with AVRAAM PITTAKIS and SONS LTD. 44

50 GROUTS SERIES GROUTS FOR FLOORS, WALLS & POOLS Available Colours: - Alfa Armos 501 White - Alfa Armos 502 Light Beige - Alfa Armos 503 Beige - Alfa Armos 504 Caramel - Alfa Armos 505 Grey - Alfa Armos 506 Dark Grey - Alfa Armos 507 Brown - Alfa Armos 508 Slate Grey - Alfa Armos 509 Deep Orange - Alfa Armos 510 Royal Blue 45-48

51 Introduction: ALFA ARMOS Alfa GROUT CG2- Super strength, Flexible, Acrilic, Waterproof, excellent quality with base the cement, powder and different chemical additives. It can be used for measurements from 1-8mm. It has excellent results in the accretions and dryness, and it is offered in various colours. It is applied ion indoor and outdoor use of floors and wall as also in pools. Preparation of sub layer: For better results we must follow the rules below. The surfaces that the mixture will be placed on different walls or floors have to be well clean from dust, oil, polyurethane, or other material. If the substrates are rusted and destroyed must be carefully cleaned and removed from any other materials. We have to be careful that the area where the mixture is done (bucket), is made by a product which can be easily cleaned. During the preparation of the product, you must be sure that the metals of the spatula or buckets do not have any signs of rust that can affect negatively the chemical reaction and the color of the adhesive. We also have to be careful that the containers we will use are easy to clean and they will always be clean before use. At the end of day, we suggest you clean all the instruments used, because the miss cleaning of the instruments can conclude in bad colors on your final construction. The chemical reactions of the materials can affect the soldering (in alkali trestle we use primer). The substrate must be a smooth surface, so the use of overdose adhesive is not needed. With this method, we will cover all the anomalies of the floor or wall. Do not forget that all the construction products are producing for the best possible quality, save time and perfect essential result. Preparation of Mixture: We mix 5kg ALFA GROUT with roughly 1,5liters clean water in a clean container, always with electric stirrer until we achieve uniform pastry. Wait for 5 minutes and mix again. The material is ready for use. ALFA GROUT has life in the container for approximately 4 hours when we stir every 1 hour. We do not add water, simply we stir with an electric blender. Most minimum time for light use 48 hours and the time of final use 14 days. 45

52 Directives of Use: 1. We stretch out the rabbet with spatula, diagonally on the ceramic, until we fill the rabbets between ceramic and there are no remaining voids. 2. When the rabbet becomes blear, (in temperatures above 23ºC the open time of application is decreased and in temperatures under 23ºC is increased) we rub him with a sponge. When it almost dries out, then we use a soft cloth for the final cleaning of ceramic. 3. The grouting becomes at least 24 hours afterwards the placement of the ceramic. 4. If we proceed in cleaning more early or add more water than that it should have, it is likely we have chromatic alteration of our rabbet. 5. In order to cover 1 sq.m with roughly 2-3mm [systolodiastoli] we will need 1/2 Kg Alfa GROUT. For other uses it depends on type and surface that it will be placed. Constitutions: The grout shouldn t get involved with cement or other material, neither with dirty water. The quantity of water should be exact, in order to have the result we wish. The temperatures that can be used by the mixture are +5 C up to +40 C. 46

53 Technical characteristics (typical numbers): Alfa ARMOS Product definition: Type: Powder Colour: 8 Different Colors Specific Gravity: 1.30 kg/lt Composition of dry materials: 100% Storage: 9 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg or boxes of 5x5kg bags Toxicity / Inflammability: No Elements of use: Composition of Mixture: Thick Water Requirements: 5kg Powder roughly 1,5 Liters Water Specific gravity of mixture: 1.7 kg/lt PH Mixture: 11 Self life in bucket: 4 Hours/ mix every 1/2 hour Application Temperature: +5 ºC ºC Growthing Time: 48 Hours Time for Final use: 14 Days Consumption: 0.5-2kg/m² Depending on use Strengths: Humidity: Excellent Acids-Alkali: Poor Temperature: -30ºC until+90ºc Declaration tests for marked CE: CG2 Resistance in bending: (28 days) 6.6 N/mm2 Resistance in sadness: (28 days) 25.2 N/mm2 Resistance in bending after the 4.5 N/mm2 refrigeration: Resistance in sadness after the 19.0 N/mm2 refrigeration: Shrinking: 1,88 N/mm2 Absorption of water: (30minutes) 0.58 N/mm2 Absorption of water: (240 minutes) 1.34 N/mm2 Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 47

54 48

55 PLASTERS & MORTARS CONSTRUCTION MATERIALS PRODUCERS PLASTERS & MORTARS 49-92

56 PLASTERS SERIES PLASTERS FOR 1 ST, 2 ND & 3 RD HAND PLASTERING 49-78

57 Introduction: 3 RD HAND PLASTER Paralimnitiko 3 rd hand indoor area is used as coating of final smoothing on plastered surfaces 2 nd hand plaster. It observes the European specifications CE MARKING CYS EN The excellently manufactured Paralimnitiko 3rd hand plaster is a ready cement mortar with base the lime powder, cement and lime. The various chemical additives combine the perfect accretion on the surface. Mixture, Preparation of sub layer and examples of enforcements: 1. We add clean water into an empty container or a concrete mixer. 2. We place into the empty container or the concrete mixer, first the water and after the material one by one. 3. The mixture is made with an electric mixer or a concrete mixer, mixing at low speed until the material becomes a smooth mass. We leave the mixture to mature for 5 minutes and then we mix again. 4. We use the mixture when it is still fresh, and we continue carefully the above instruction. We do not leave the mixture unmixed for a long time. A fast way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then we can use the mixture. 5. The mixture can be stored in the container for a maximum of hour after the mix. 6. After a while we do not mix or add water because of some negative mechanical strength. Appliance: 1. The surface which will the mixture be applied has to be clean from dust, any other material, or oil and has to be sprinkled with water well before use. 2. The substrate has to be flat without any anomalies for better final appliance. 3. When the surface has a big absorption then good sprinkling of the surface is needed. 4. It is applied with a trowel in 2 cruciate layers and after the first pulls, we place the second layer. The final surface can be rubbed with [tribidi] from sponge or timber. After 24 hours it is sprinkled with some water. 5. The width of the appliance on the mixture for each layer could be from 2-4mm. 6. The plastered surface has to dry for 24 hours after it can be anchored with sandpaper. The surface can be decorated with many kinds of coatings such as texture finishes Pittakis Grafit, Flash Spa compound, emulsion paints, oil paints, acrylic paints and wall paper. Also, from the Alfakol 6* until Alfakol 24*. 49

58 Warning: We avoid the application of 3 rd hand at high sun shines, temperatures and also hot wind. As result, is to avoid cracks during the period of dryness and maturation of the surface. Technical characteristics: 3 rd hand Plaster: Product definition: Type: Powder Granulometry: mm Colour: Grey Specific Gravity: 1.45 kg/lt Composition of dry materials: 100% Storage: 4 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use : Composition of mixture: Thick Water requirements: 25kg Powder with roughly 8 Liters Water Mixture weight: 1.60 kg/lt Application temperature: +5 ºC ºC ΡΗ mixture: >10 Self life in bucket: Approximately 1 hour Application width: 2-4 mm Consumption: 3-4 kg/m² depending use/surface Time of maturing: 14 days Strengths: Flexibility: No Shrinking: No Acids-Alkali: Excellent Humidity: Excellent Resistance in the welding: 0,39 N/mm² Resistance in the compaction: 6,8 N/mm² Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 50

59 Declaration of Performance: No.: AP033 CPR - 01/07/ Unique identification code of the product-type: 3rd Hand plaster Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7.In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9.Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 0.3 Ν/mm 2 - FΡ: B CSIII Water Absorption W0 Water Vapour permeability coefficient μ 19 Dry Bulk Density 1350 kg/m 3 Thermal Conductivity, λ 10, dry Durability (against freeze/thaw) 0.4 W/m K for Ρ=50% Evaluation based on provisions valid in the intended place of use of the mortar. Harmonised Technical Specification ΕΝ 998-1: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

60 3 rd HAND PLASTER WITH FIBERS Introduction: Paralimnitiko 3 rd hand indoor and outdoor area is used as coating of final smoothing on plastered surfaces 2 nd hand plaster. It observes the European specifications CE MARKING CYS EN The excellently manufactured Paralimnitiko 3rd hand plaster with fibers is a ready cement mortar with base the lime powder, cement and lime. The various chemical additives and fibers combine the perfect accretion on the surface. Mixture, Preparation of sub layer and examples of enforcements: 1. We add clean water into an empty container or a concrete mixer. 2. We place into the empty container or the concrete mixer, first the water and after the material one by one. 3. The mixture is made with an electric mixer or a concrete mixer, mixing at low speed until the material becomes a smooth mass. We leave the mixture to mature for 5 minutes and then we mix again. 4. We use the mixture when it is still fresh, and we continue carefully the above instruction. We do not leave the mixture unmixed for a long time. A fast way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then we can use the mixture. 5. The mixture can be stored in the container for a maximum of hour after the mix. 6. After a while we do not mix or add water because of some negative mechanical strength. Appliance: 1. The surface which will the mixture be applied has to be clean from dust, any other material, or oil and has to be sprinkled with water well before use. 2. The substrate has to be flat without any anomalies for better final appliance. 3. When the surface has a big absorption then good sprinkling of the surface is needed. 4. It is applied with a trowel in 2 cruciate layers and after the first pulls, we place the second layer. The final surface can be rubbed with [tribidi] from sponge or timber. After 24 hours it is sprinkled with some water. 5. The width of the appliance on the mixture for each layer could be from 2-4mm. 6. The plastered surface has to dry for 24 hours after it can be anchored with sandpaper. The surface can be decorated with many kinds of coatings such as texture finishes Pittakis Grafit, Flash Spa compound, emulsion paints, oil paints, acrylic paints and wall paper. Also, from the Alfakol 6* until Alfakol 24*. 52

61 Warning: We avoid the application of 3rd hand at high sun shines, temperatures and also hot wind. As result, is to avoid cracks during the period of dryness and maturation of the surface. Technical characteristics: 3rd hand Plaster with Fibers: Product definition: Type: Powder Granulometry: mm Colour: Grey Specific Gravity: 1.45 kg/lt Composition of dry materials: 100% Storage: 4 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use : Composition of mixture: Thick Water requirements: 25kg Powder with roughly 8 Liters Water Mixture weight: 1.60 kg/lt Application temperature: +5 ºC ºC ΡΗ mixture: >10 Self life in bucket: Approximately 1 hour Application width: 2-4 mm Consumption: 3-4 kg/m² depending use/surface Time of maturing: 14 days Strengths: Flexibility: Shrinking: Acids-Alkali: Humidity: Resistance in the welding: Resistance in the compaction: No No Excellent Excellent 0,49 N/mm² 7.4 N/mm² Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 53

62 Declaration of Performance: No.: AP034 CPR - 01/07/ Unique identification code of the product-type: 3rd Hand plaster with fibers Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7.In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 0.3 Ν/mm 2 - FΡ: B CSIII Water Absorption W0 Water Vapour permeability coefficient μ 18 Dry Bulk Density 1430 kg/m 3 Thermal Conductivity, λ 10, dry Durability (against freeze/thaw) 0.4 W/m K for Ρ=50% Evaluation based on provisions valid in the intended place of use of the mortar. Harmonised Technical Specification ΕΝ 998-1: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

63 THERMO 3 rd Hand THERMO 3 ο ΧΕPΙ is superstrength, 3 ο hand plaster reinforced with fibers, based on cement, lime, non-absorbent fine grained sand and special additives. Suitable for interiorexterior applications on 2 nd hand plastered surfaces thermal insulated or not. Instructions for use: Surface preparation: The substrate must be flat and clean from dust or oils. For better adhesion the surfaces should be lightly moistened with little water. Mixing: Pour a 25 kg back into a bucket containing 7 8 L water. Mix with a low speed mixer or a concrete machine until a homogeneous lump free paste is obtained. Leave the mixture to stand for about 5 minutes and mix again. The pot life of the mix is 3 4 hours, depending on temperature and humidity. Application: The substrate is cleaned and moistened. The mixture is applied by spatula or steel trowel, in two or more coats. The first coat fills the roughness of the surface. Successive coats produce a smooth even surface. Every next coat is applied when the previous one has set. The total thickness should be in the order of 2 4 mm. The final surface may either be finished with a trowel covered with sponge or made smooth with a steel trowel s edge. The plastered surface should be lightly dampened, for 2 3 days, beginning 24 hours after application, especially in hot weather, with intense evaporation. Decoration: Surface should first be made smooth using sandpaper. Acrylic and oil paints may be used for painting. Weather Conditions: Use at temperatures between +5 o C and +40 o C. Too high or too low temperatures, it might cause a negative reaction to the product. Storage: All cement base products must be stored in dry areas, in original unopened packaging on wooden pallets. Even under these conditions, after a period of time the material is influenced by the atmosphere humidity. Do not use the product if it has hardened. The storage time should not exceed 8 months. 55

64 Technical characteristics (typical values): THERMO 3 ο ΧΕΡΙ Product Identity Consistency: Powder Colour: Grey Dry Solid content (%): 100% Storage: 8months in a dry place in original unopened packaging Granulometry: mm Package & Weight: Bags of 25kg Toxicity / Inflammability: NO Application data Consistency of mix: Paste Mix Ratio: 25kg Powder with 7-8 Liters Water Wet density: 1.4 kg/lt Application temperature range: +5 ºC ºC pη of the mix: >10 Pot Life: 3-4 hours Consumption: 3-5 kg/m² depending on use and surface (recommended thickness 4mm in two coats) Final Performances Shrinkage: Resistance to fire: Adhesive Bond (28 days) Compressive Strength (28 days) Thermal conductivity (λ10,dry) Results No Class A1 0.3 N/mm² - FP:B 4.5 N/mm² - CSII 0.45 W/m.K - tab. Mean value, P=50% Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information, contact with AVRAAM PITTAKIS and SONS LTD. 56

65 Declaration of Performance: No.: AP097 CPR - 01/07/ Unique identification code of the product-type: Thermo 3rd hand Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7.In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 0.3 Ν/mm 2 - FΡ: B CSII Water Absorption W0 Water Vapour permeability coefficient μ 10 Dry Bulk Density 1450 kg/m 3 Thermal Conductivity, λ 10, dry Durability (against freeze/thaw) 0.45 W/m K for Ρ=50% Evaluation based on provisions valid in the intended place of use of the mortar. Harmonised Technical Specification ΕΝ 998-1: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

66 EXELASTIC FLEXIBLE ACRYLIC Exelastic Plast Acrylic is a compound coat with base the cement, lime, powder and it is strengthened with resins and synthetic fibers. The various chemical additives combine the perfect accretion on the surface. Ideal for indoor and outdoor areas, for final plaster on plastered surfaces, on cement board, polystyrene, Fair Face beton, or for 2 nd and 3 rd hand plaster, for closing whether painted surfaces or not, Sprits and Sagre. There mustn t be humidity in stonework and the sublayer must be strong. Also, ideal for application near to the beach. Mixture, Preparation of sub layer and examples of enforcements: 1. We add clean water into an empty container or a concrete mixer. 2. We place into the empty container or the concrete mixer, first the water and after the material one by one. 3. The mixture is made with an electric mixer or a concrete mixer, mixing at low speed until the material becomes a smooth mass. We leave the mixture to mature for 5 minutes and then we mix again. 4. We use the mixture when it is still fresh, and we continue carefully the above instruction. We do not leave the mixture unmixed for a long time. A fast way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then we can use the mixture. 5. The mixture can be stored in the container for a maximum of hour after the mix. 6. After a while we do not mix or add water because of some negative mechanical strength. Appliance: 1. The surface which will the mixture be applied has to be clean from dust, any other material, or oil and has to be sprinkled with water well before use. 2. The substrate has to be flat without any anomalies for better final appliance. 3. When the surface has a big absorption then good sprinkling of the surface is needed. 4. It is applied with a trowel in 2 cruciate layers and after the first pulls, we place the second layer. The final surface can be rubbed with [tribidi] from sponge or timber. After 24 hours it is sprinkled with some water. 5. The width of the appliance on the mixture for each layer could be from 2-4mm. 6. The plastered surface has to dry for 24 hours after it can be anchored with sandpaper. The surface can be decorated with many kinds of coatings such as texture finishes Pittakis Grafit, Flash Spa compound, emulsion paints, oil paints, acrylic paints and wall paper. Also, from the Alfakol 6* until Alfakol 24*. Warning: We avoid the application of extra plast at high sun shines, temperatures and also hot wind. As result, is to avoid cracks during the period of dryness and maturation of the surface. 58

67 Technical characteristics: Exelastic Plast Flexible Acrylic Product definition: Type: Powder Granulometry: mm Colour: Grey Specific Gravity: 1.45 kg/lt Composition of dry materials: 100% Storage: 6 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use : Composition of mixture: Thick Water requirements: 25kg Powder with roughly 8 Liters Water Mixture weight: 1.68 kg/lt Application temperature: +5 ºC ºC ΡΗ mixture: >10 Self life in bucket: Approximately 1 hour Application width: 2-4 mm Consumption: 3-5 kg/m² depending use/surface Time of maturing: 14 days Strengths: Flexibility: Shrinking: Acids-Alkali: Humidity: Yes No Excellent Excellent Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 59

68 Declaration of Performance: No.: AP088 CPR - 01/07/ Unique identification code of the product-type: EXELASTIC PLAST Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 1.3 Ν/mm 2 - FΡ: B CSIV Water Absorption W1 Water Vapour permeability coefficient μ 4 Dry Bulk Density 1450 kg/m 3 Thermal Conductivity, λ 10, dry Durability (against freeze/thaw) 0.45 W/m K for Ρ=50% Evaluation based on provisions valid in the intended place of use of the mortar. Harmonised Technical Specification ΕΝ 998-1: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

69 EXTRA PLAST Extra Plast is a compound coat with base the cement, lime, powder and it is strengthened with resins and synthetic fibers. The various chemical additives combine the perfect accretion on the surface. Ideal for indoor and outdoor areas, for final plaster on plastered surfaces, polystyrene, Fair Face beton, or for 2 nd and 3 rd hand plaster. Mixture, Preparation of sub layer and examples of enforcements: 1. We add clean water into an empty container or a concrete mixer. 2. We place into the empty container or the concrete mixer, first the water and after the material one by one. 3. The mixture is made with an electric mixer or a concrete mixer, mixing at low speed until the material becomes a smooth mass. We leave the mixture to mature for 5 minutes and then we mix again. 4. We use the mixture when it is still fresh, and we continue carefully the above instruction. We do not leave the mixture unmixed for a long time. A fast way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then we can use the mixture. 5. The mixture can be stored in the container for a maximum of hour after the mix. 6. After a while we do not mix or add water because of some negative mechanical strength. Appliance: 1. The surface which will the mixture be applied has to be clean from dust, any other material, or oil and has to be sprinkled with water well before use. 2. The substrate has to be flat without any anomalies for better final appliance. 3. When the surface has a big absorption then good sprinkling of the surface is needed. 4. It is applied with a trowel in 2 cruciate layers and after the first pulls, we place the second layer. The final surface can be rubbed with [tribidi] from sponge or timber. After 24 hours it is sprinkled with some water. 5. The width of the appliance on the mixture for each layer could be from 2-4mm. 6. The plastered surface has to dry for 24 hours after it can be anchored with sandpaper. The surface can be decorated with many kinds of coatings such as texture finishes Pittakis Grafit, Flash Spa compound, emulsion paints, oil paints, acrylic paints and wall paper. Also, from the Alfakol 6* until Alfakol 24*. Warning: We avoid the application of extra plast at high sun shines, temperatures and also hot wind. As result, is to avoid cracks during the period of dryness and maturation of the surface. 61

70 Technical characteristics: Extra Plast: Product definition: Type: Powder Granulometry: mm Colour: Grey and White Specific Gravity: 1.45 kg/lt Composition of dry materials: 100% Storage: 6 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use : Composition of mixture: Thick Water requirements: 25kg Powder with roughly 8 Liters Water Mixture weight: 1.68 kg/lt Application temperature: +5 ºC ºC ΡΗ mixture: >10 Self life in bucket: Approximately 1 hour Application width: 2-4 mm Consumption: 3-5 kg/m² depending use/surface Time of maturing: 14 days Strengths: Flexibility: Shrinking: Acids-Alkali: Humidity: Adhesive Bond (28 days): Compressive Strength (28 days): Thermal Conductivity (λ10,dry) No No Excellent Excellent 0.5 N/mm² - FP:B 9.8 N/mm² - CSIV 0.4 W/m.K standard table value Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 62

71 Declaration of Performance: No.: AP012 CPR - 01/07/ Unique identification code of the product-type: EXTRA PLAST Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7.In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 0.5 Ν/mm 2 - FΡ: B CSIV Water Absorption W2 Water Vapour permeability coefficient μ 17 Dry Bulk Density 1450 kg/m 3 Thermal Conductivity, λ 10, dry Durability (against freeze/thaw) 0.4 W/m K for Ρ=50% Evaluation based on provisions valid in the intended place of use of the mortar. Harmonised Technical Specification ΕΝ 998-1: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

72 SMART PLAST THICK Smart Plast thick Granulated is a coat with base the cement, lime, sand and it is strengthened with resins and synthetic fibers. The various chemical additives combine the perfect accretion on the surface. Ideal for indoor and outdoor areas, for first plaster on blocks, bricks, Climalite Daliko, Ytong, Fair Face Wild, Cement plaster, Cement stones, Polystyrene and for closing surfaces with Sprits, provided that there isn t any humidity on the stonework and the sublayer is strong. Mixture, Preparation of sub layer and examples of enforcements: 1. We add clean water into an empty container or a concrete mixer. 2. We place into the empty container or the concrete mixer, first the water and after the material one by one. 3. The mixture is made with an electric mixer or a concrete mixer, mixing at low speed until the material becomes a smooth mass. We leave the mixture to mature for 5 minutes and then we mix again. 4. We use the mixture when it is still fresh, and we continue carefully the above instruction. We do not leave the mixture unmixed for a long time. A fast way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then we can use the mixture. 5. The mixture can be stored in the container for a maximum of 1/2 hour after the mix. 6. After a while we do not mix or add water because of some negative mechanical strength. Appliance: 1. The surface which will the mixture be applied has to be clean from dust, any other material, or oil and has to be sprinkled with water well before use. 2. The substrate has to be flat without any anomalies for better final appliance. 3. When the surface has a big absorption then good sprinkling of the surface is needed. 4. After the [tsimes] are made, the material is applied in the desirable thickness. The layer has to be approximately 10-12mm. 5. After the appliance, it has to be sprinkled for 2-3 days. 6. A 25kg sack covers approximately 2-2.5m 2 of plastering with thickness 10mm always under normal conditions. 7. The surface can be covered with all Paralimnitiko plasters and adhesives Alfakol. We suggest the final layer is with Smartplast thin granulated for a spoiler surface. Warning: We avoid the application at high sun shines, temperatures and also hot wind. As result, is to avoid cracks during the period of dryness and maturation of the surface. The plastered surface has to stay so it absorbs for at least 7 days in summer, and 14 days in winter, so the cracks can be covered with the next plaster. 64

73 Technical characteristics: Smart Plast Thick Granulated Product definition: Type: Powder Granulometry: mm Colour: Grey Or White Specific Gravity: 1.45 kg/lt Composition of dry materials: 100% Storage: 6 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use : Composition of mixture: Thick Water requirements: 25kg Powder with roughly 8 Liters Water Mixture weight: 1.75 kg/lt Application temperature: +5 ºC ºC ΡΗ mixture: >10 Self life in bucket: Approximately 1 hour Application width: mm Consumption: 6-8 kg/m² depending use/surface Time of maturing: 14 days Strengths: Flexibility: Shrinking: Acids-Alkali: Humidity: Resistance in the welding: Resistance in the bending: Resistance in the compaction: No No Excellent Excellent 1,7 N/mm² 8,4 N/mm² 13,8 N/mm² Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 65

74 Declaration of Performance: No.: AP075 CPR - 01/07/ Unique identification code of the product-type: SMART PLAST THICK Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7.In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9.Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 0.6 Ν/mm 2 - FΡ: B CSIV Water Absorption W2 Water Vapour permeability coefficient μ 19 Dry Bulk Density 1570 kg/m 3 Thermal Conductivity, λ 10, dry Durability (against freeze/thaw) 0.6 W/m K for Ρ=50% Evaluation based on provisions valid in the intended place of use of the mortar. Harmonised Technical Specification ΕΝ 998-1: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

75 SMART PLAST FINE Smart Plast fine Granulated is a coat with base the cement, lime, sand and it is strengthened with resins and synthetic fibers. The various chemical additives combine the perfect accretion on the surface. Ideal for indoor and outdoor areas, for final layer, on plastered surfaces Smart Plast thick granulated, 2 nd hand plaster, Ytong, Fair Face and Cement stones. Mixture, Preparation of sub layer and examples of enforcements: 1. We add clean water into an empty container or a concrete mixer. 2. We place into the empty container or the concrete mixer, first the water and after the material one by one. 3. The mixture is made with an electric mixer or a concrete mixer, mixing at low speed until the material becomes a smooth mass. We leave the mixture to mature for 5 minutes and then we mix again. 4. We use the mixture when it is still fresh, and we continue carefully the above instruction. We do not leave the mixture unmixed for a long time. A fast way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then we can use the mixture. 5. The mixture can be stored in the container for a maximum of 1 hour after the mix. 6. After a while we do not mix or add water because of some negative mechanical strength. Appliance: 1. The surface which will the mixture be applied has to be clean from dust, any other material, or oil and has to be sprinkled with water well before use. 2. The substrate has to be flat without any anomalies for better final appliance. 3. When the surface has a big absorption then good sprinkling of the surface is needed. 4. It is applied with a trowel in 2 cruciate layers and after the first pulls, we place the second layer. The final surface can be rubbed with tool from sponge or timber. After 24 hours it is sprinkled with some water. 5. The width of the appliance on the mixture for each layer could be from 2-4mm. 6. The plastered surface has to dry for 24 hours after it can be anchored with sandpaper. The surface can be decorated with many kinds of coatings such as texture finishes Pittakis Grafit, Flash Spa compound, emulsion paints, oil paints, acrylic paints and wall paper. Also, from the Alfakol 6* until Alfakol 24*. Warning: We avoid the application of smart plast at high sun shines, temperatures and also hot wind. As result, is to avoid cracks during the period of dryness and maturation of the surface. 67

76 Technical characteristics: Smart Plast Fine Granulated: Product definition: Type: Powder Granulometry: mm Colour: Grey and White Specific Gravity: 1.45 kg/lt Composition of dry materials: 100% Storage: 6 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use : Composition of mixture: Thick Water requirements: 25kg Powder with roughly 8 Liters Water Mixture weight: 1.68 kg/lt Application temperature: +5 ºC ºC ΡΗ mixture: >10 Self life in bucket: Approximately 1 hour Application width: 2-4 mm Consumption: 3-5 kg/m² depending use/surface Time of maturing: 14 days Strengths: Flexibility: No Shrinking: No Acids-Alkali: Excellent Humidity: Excellent Resistance in the welding: 1.6 N/mm² Resistance in the bending: 8.2 N/mm 2 Resistance in the compaction: 13.4 N/mm² Thermal Conductivity (λ): 0,5 W/mk Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 68

77 Declaration of Performance: No.: AP079 CPR - 01/07/ Unique identification code of the product-type: SMART PLAST FINE Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7.In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 0.5 Ν/mm 2 - FΡ: A CSIV Water Absorption W1 Water Vapour permeability coefficient μ 17 Dry Bulk Density 1450 kg/m 3 Thermal Conductivity, λ 10, dry Durability (against freeze/thaw) 0.4 W/m K for Ρ=50% Evaluation based on provisions valid in the intended place of use of the mortar. Harmonised Technical Specification ΕΝ 998-1: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

78 SMARTELASTIC PLAST Thick SMARTELASTICK PLAST Thick-granulated is a cement base superstrength initialfinal plaster, reinforced with fibers, synthetic resins and special additives that improve the adhesion on different substrates. Suitable for interior-exterior applications on cement blocks, bricks thermal insulated or no, Climalite, Ytong, plastered surfaces and Fair Face. Moreover, it can be used as an application on Sprits surface, whether painted or not, only if there is no humidity and the wall is strong. Instructions for use: Surface preparation: The substrate must be solid, dry and free of dust, loose parts or oils. Surfaces that are not sufficiently solid must be removed. For better adhesion thorough dampening of the substrate before application is necessary. Mixing: Add 25kg SMARTELASTIC PLAST Thick-granulated to 7 8 L water. Mix in a concrete machine or with an electrical mixer until a smooth uniform mix is produced, leave the mixture to stand for about 5 minutes and mix again. After the product begins to set do not add any water because of negative mechanical strengths. Application: The substrate is cleaned and moistened. Application can be done using level guides to the desirable thickness. Each layer must be around mm. For trowel application thickness should be 5mm for each layer. Plastered surfaces should be wetted for 2-3 days. Decoration: The plastered surface has to dry out completely (7-14 days) so you can cover with a coating the small cracks and the shrinkable of the layer after you have wetted the surface with water. The plastered surface can be decorated with a wide range of paints, texture finishes or compounds available by Paralimnitiko. We recommend the use of SMART PLAST fine granulated for a smooth surface. Weather Conditions: Use at temperatures between +5 o C and +40 o C. Too high or too low temperatures, it might cause a negative reaction to the product. PROTECT FROM HUMIDITY Storage: All cement base products must be stored in dry areas, in original unopened packaging on wooden pallets. Even under these conditions, after a period of time the material is influenced by the atmosphere humidity. Do not use the product if it has hardened. The storage time should not exceed 8 months. 70

79 Technical characteristics (typical values): SMARTELASTIC PLAST Thick- Granulated Product Identity Colour - Consistency: Grey Powder Dry Solid content (%): 100% Granulometry: mm Dry bulk density: 1450 kg/m 3 Storage: 8months in a dry place in original unopened packaging Package & Weight: Bags of 25kg Toxicity / Inflammability: NO Application data Consistency of mix: Paste Mix Ratio: 25kg Powder with 7-8 Liters Water Wet density: 1750 kg/m 3 Application temperature range: +5 ºC ºC pη of the mix: >10 Pot Life: 1 hour Application thickness: mm Consumption: kg/m² depending on use and surface Waiting time before finishing: 7 days for winter and 14 days for summer period Final Performances Shrinkage: Resistance to fire: Adhesive Bond (28 days): Compressive Strength (28 days): Water absorption: Thermal conductivity (λ10,dry) Results No Class A1 1 N/mm² - FP:B 14.9 N/mm² - CSIV 0.26 kg/m 2 min 0.5 W W/m.K - tab. Mean value, P=50% Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information, contact with AVRAAM PITTAKIS and SONS LTD. 71

80 Declaration of Performance: No.: AP022 CPR - 01/07/ Unique identification code of the product-type: SMARTELASTIC PLAST THICK Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7.In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 1 Ν/mm 2 - FΡ: B CSIV Water Absorption W1 Water Vapour permeability coefficient μ 8 Dry Bulk Density 1450 kg/m 3 Thermal Conductivity λ 10, dry Durability (against freeze/thaw) 0.45 W/m K for Ρ=50% Evaluation based on provisions valid in the intended place of use of the mortar. Harmonised Technical Specification ΕΝ 998-1: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

81 LIMEPLASTER UNDERCOAT Thick LIMEPLASTER UNDERCOAT is a ready mixed initial plaster without cement, based on lime, limestone powder, perlite and special additives that give high elasticity and improved adhesion to the final product. Suitable for plastering surfaces of stone, bricks, concrete blocks etc. Ideal for stone that is chemically incompatible with cement mortars, for restoration of traditional buildings and hagiography (painting of holy icons on building surfaces). Instructions for use: Surface preparation: THICK-GRANULATED LIMEPLASTER is generally applied to clean and sound surfaces. Cracks or cavities are suitably filled and allowed to cure. To avoid immediate absorption of mix water by the substrate and for better adhesion saturate the surface to provide a saturated surface dry condition. Mixing: Pour 25L LIMEPLASTER Thick-granulated to 8 L water. Mix in a concrete machine for big quantities or with a low speed electric mixer for small quantities, until a homogeneous lump free mix is obtained. Mixing period should not exceed 5 minutes because it might cause adverse effect on its mechanical properties. Leave the mixture to stand for about 5 minutes and mix again. The mix remains workable, in the container for about min depending on ambient temperature and humidity. After the product begins to set do not add any water because of negative mechanical strengths. Application: Application can be done using level guides and wedges, by either a trowel or float. Thickness can vary according to the overall thickness required but it is normally between 25 and 30 mm. It must not be applied over 30 mm thick. If this is required it should be done as an extra coat (two intermediate coats). The plastered surface remains workable for a few days, if sprayed with water immediately before. Then rub with a wooden or plastic flat. Next day the surface is perfected, immediately after spraying with water. Keep the surface wet for at least 30 days, especially in hot weather. Decoration: For practical reasons plastered surface should remain unpainted for several months. Weather Conditions: Use at temperatures between +5 o C and +40 o C. Too high or too low temperatures, it might cause a negative reaction to the product. Storage: All lime based products must be stored in dry areas, in original unopened packaging on wooden pallets. Even under these conditions, after a period of time the material is influenced by the atmosphere humidity. Do not use the product if it has hardened. The storage time should not exceed 9 months. 73

82 Technical characteristics (typical values): LIMEPLASTER UNDERCOAT Thick - Granulated Product Identity Colour / Consistency: White Powder Dry Solid content (%): 100% Storage: 9 months in a dry place in original unopened packaging Granulometry: 0 3 mm Bulk Density: 800 kg/m 3 Package & Weight: Bags of 25Lt Toxicity / Inflammability: NO Application data Consistency of mix: Paste Mix Ratio: 25L Powder with 8 Liters Water Wet density: 1150 kg/m 3 Application temperature range: +5 ºC ºC pη of the mix: >10 Pot Life: 1 hour Application thickness: mm Consumption: 25 L/m² for 20-25mm Final Performances Shrinkage: Adhesive Bond (28 days) Compressive Strength (28 days) Thermal conductivity (λ10,dry) Results No 0.2 N/mm² - FP:B 0.4 N/mm² - CSI 0.25 W/m.K - tab. Mean value, P=50% Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information, contact with AVRAAM PITTAKIS and SONS LTD. 74

83 Declaration of Performance: No.: AP127 CPR - 01/07/ Unique identification code of the product-type: Limeplaster Thick Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3.Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4.Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5.Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6.System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7.In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9.Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 0.2 Ν/mm 2 - FΡ: B CSI Water Absorption W0 Water Vapour permeability coefficient μ 5 Dry Bulk Density 800 kg/m 3 Thermal Conductivity λ 10, dry Durability (against freeze/thaw) 0.25 W/m K for Ρ=50% Evaluation based on provisions valid in the intended place of use of the mortar. Harmonised Technical Specification ΕΝ 998-1: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

84 LIMEPLASTER FINISH Fine LIMEPLASTER FINSH is a fine granulated ready mixed plaster without cement, based on lime, limestone powder, perlite and special additives that improve the adhesion and elasticity of the final product. Limeplaster Fine-Granulated can be used as a finish coat on Lime Plaster Undercoat, or directly to the surface. Ideal for plastering surfaces of stone, that is chemically incompatible with cement mortars and hagiography (painting of holy icons on building surfaces). Instructions for use: Surface preparation: LIME PLASTER finish is generally applied to clean sound surfaces. Cracks or cavities are suitably filled and allowed to cure. To avoid immediate absorption of mix water by the substrate and for better adhesion saturate the surface to provide a saturated surface dry condition. Mixing: Add 25L LIME PLASTER Finish to L water. Mix in a concrete machine or with an electrical mixer until a smooth uniform mix is produced. Then leave the mixture for about 5 minutes and mix again. The mixture remains workable in the container for about minutes. After the product begins to set do not add any water. Application: Application can be done using level guides or not, depending on the nature of the surface and the required result. Apply directly to the surface by either a trowel or a float. In case that the application will be with a trowel the thickness of each layer should not be more than 0.5 cm. The plastered surface remains workable for a few days, if sprayed with water immediately before. Then rub with a wooden or plastic flat. Next day the surface is perfected, immediately after spraying with water. Keep the surface wet for at least 30 days, especially in hot weather. Decoration: : For practical reasons FINE - GRANULATED LIME PLASTER should remain unpainted for several months. Storage: All lime based products must be stored in dry areas, in original unopened packaging on wooden pallets. Even under these conditions, after a period of time the material is influenced by the atmosphere humidity. Do not use the product if it has hardened. The storage time should not exceed 9 months. 76

85 Technical characteristics (typical values): LIMEPLASTER FINISH Fine- Granulated Product Identity Colour / Consistency: White Powder Dry Solid content (%): 100% Storage: 9 months in a dry place in original unopened packaging Granulometry: mm Bulk Density: 1100 kg/m 3 Package & Weight: Bags of 25Lt Toxicity / Inflammability: NO Application data Consistency of mix: Paste Mix Ratio: 25L Powder with Liters Water Wet density: 1350 kg/m 3 Application temperature range: +5 ºC ºC pη of the mix: >10 Pot Life: 1 hour Application thickness: 5-20 mm Consumption: 3-5 L/m² depending on use Final Performances Shrinkage: Adhesive Bond (28 days) Compressive Strength (28 days) Thermal conductivity (λ10,dry) Results No 0.2 N/mm² - FP:B CSI 0.4 W/m.K - tab. Mean value, P=50% Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information, contact with AVRAAM PITTAKIS and SONS LTD. 77

86 Declaration of Performance: No.: AP128 CPR - 01/07/ Unique identification code of the product-type: Limeplaster Fine Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 0.2 Ν/mm 2 - FΡ: B CSI Water Absorption W0 Water Vapour permeability coefficient μ 6 Dry Bulk Density 1100 kg/m 3 Thermal Conductivity λ 10, dry Durability (against freeze/thaw) 0.4 W/m K for Ρ=50% Evaluation based on provisions valid in the intended place of use of the mortar. Harmonised Technical Specification ΕΝ 998-1: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

87 MORTARS SERIES MORTARS FOR BUILDING and PLASTERING VARIOUS BRICKS & BLOCKS 79-92

88 ALFAKOL 1* Alfakol 1* is a thick grounded adhesive - plster in different colors with main ingredients: cement, sand and various chemical additives. Ideal for building and coating different kind of bricks (colored bricks and blocks), Climalite Daliko and cement blocks. Mixture, Preparation of sub layer and examples of enforcements: 1. We add clean water into an empty container or a concrete mixer. 2. We place into the empty container or the concrete mixer, first the water and after the material one by one. 3. The mixture is made with an electric mixer or a concrete mixer, mixing at low speed until the material becomes a smooth mass. We leave the mixture to mature for 5 minutes and then we mix again. 4. We use the mixture when it is still fresh, and we continue carefully the above instruction. We do not leave the mixture unmixed for a long time. A fast way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then we can use the mixture. 5. The mixture can be stored in the container for a maximum of 1 hour after the mix. 6. After a while we do not mix or add water because of some negative mechanical strength. Application: 1. The surface which will the mixture be applied has to be clean from dust, any other material, or oil and has to be sprinkled with water well before use. 2. The substrate has to be flat without any anomalies for better final appliance. 3. When the surface has a big absorption then good sprinkling of the surface is needed. 4. It can be used as a plaster of different wall bricks as 1 st and 2 nd hand. For the 2 nd hand to be done, at least one day has to pass from the enforcement of the 1 st hand. 5. A 25kg sack covers approximately 2-2.5m 2 of plastering with thickness 10mm always under normal conditions. 6. Building bricks of 20cm we need a bag of 25kg sack for 1,25m 2 and with a 10cm wall we cover 4m 2 7. The surface can be covered with all Paralimnitiko plasters. Warning: We avoid the application of Alfakol 1* at high sun shines, temperatures and also hot wind. As result, is to avoid cracks during the period of dryness and maturation of the surface. The plastered surface has to stay so it absorbs for at least 7 days in summer, and 14 days in winter, so the cracks can be covered with the next plaster. 79

89 Technical characteristics (typical numbers): Alfakol 1* Product definition: Type: Powder Granulometry: mm Colour: Cream, Grey Or Yellow Specific Gravity: 1.50 kg/lt Composition of dry materials: 100% Storage: 9 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use : Composition of mixture: Thick Water requirements: 25kg Powder with roughly 8 Liters Water Mixture weight: 1.80 kg/lt Application temperature: +5 ºC ºC ΡΗ mixture: >10 Self life in bucket: Approximately 1 hour Application width: mm Consumption: 8-10 kg/m² depending use/surface Time of maturing: 14 days Strengths: Flexibility: Shrinking: Acids-Alkali: Humidity: Resistance in the welding: Resistance in the bending: Resistance in the compaction: No No Excellent Excellent 1,8 N/mm² 7,2 N/mm² 15,8 N/mm² Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information, contact with AVRAAM PITTAKIS and SONS LTD. 80

90 Declaration of Performance: No.: AP CPR - 01/07/ Unique identification code of the product-type: ALFAKOL 1* Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 0.6 Ν/mm 2 - FΡ: B CSIV Water Absorption W1 Water Vapour permeability coefficient μ 4 Dry Bulk Density 1530 kg/m 3 Thermal Conductivity, λ 10, dry 0.53 W/m K for Ρ=50% Harmonised Technical Specification ΕΝ 998-1: 2010 Durability (against freeze/thaw) Evaluation based on provisions valid in the intended place of use of the mortar. 10. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

91 Declaration of Performance: No.: AP CPR - 01/07/ Unique identification code of the product-type: Alfakol 1* Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: Prescribed general purpose masonry mortar for external use in elements subject to structural requirements. 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-2: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Cement (mass percent) 24% Lime (mass percent) 4% Aggregates (mass percent) 74% Performance Harmonised Technical Specification Contents of chloride Reaction to fire 0.015% Cl Class Α1 ΕΝ 998-2: 2010 Water Absorption 0.32 kg/m 2.min 0.5 Water Vapour permeability coefficient μ 4 Thermal Conductivity, λ 10, dry Durability (against freeze/thaw) 0.53 W/m K for Ρ=50% Evaluation based on provisions valid in the intended place of use of the mortar. 10. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

92 PITTAKIS CEM PITTAKIS CEM is a ready plaster, with NO LIME, with base the grey cement, the sand and various chemical additives. Ideal for coat, for building various bricks and blocks. Mixture, Preparation of sub layer and examples of enforcements: 1. We add clean water into an empty container or a concrete mixer. 2. We place into the empty container or the concrete mixer, first the water and after the material one by one. 3. The mixture is made with an electric mixer or a concrete mixer, mixing at low speed until the material becomes a smooth mass. We leave the mixture to mature for 5 minutes and then we mix again. 4. We use the mixture when it is still fresh, and we continue carefully the above instruction. We do not leave the mixture unmixed for a long time. A fast way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then we can use the mixture. 5. The mixture can be stored in the container for a maximum of 1/2 hour after the mix. 6. After a while we do not mix or add water because of some negative mechanical strength. Appliance: 1. The surface which will the mixture be applied has to be clean from dust, any other material, or oil and has to be sprinkled with water well before use. 2. The substrate has to be flat without any anomalies for better final appliance. 3. When the surface has a big absorption then good sprinkling of the surface is needed. 4. It can be used as a plaster of different wall bricks as 1 st and 2 nd hand. For the 2 nd hand to be done, at least one day has to pass from the enforcement of the 1 st hand. 5. A 25kg sack covers approximately 2-2.5m 2 of plastering with thickness 10mm always under normal conditions. 6. Building bricks of 20cm we need a bag of 25kg sack for 1,25m 2 and with a 10cm wall we cover 4m 2 7. The surface can be covered with all Paralimnitiko plasters. Warning: We avoid the application of Pittakis Cem at high sun shines, temperatures and also hot wind. As result, is to avoid cracks during the period of dryness and maturation of the surface. The plastered surface has to stay so it absorbs for at least 7 days in summer, and 14 days in winter, so the cracks can be covered with the next plaster. 83

93 Technical characteristics: Pittakis Cem: Product definition: Type: Powder Granulometry: mm Colour: Grey Or Yellow Specific Gravity: 1.70 kg/lt Composition of dry materials: 100% Storage: 9 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use : Composition of mixture: Thick Water requirements: 25kg Powder with roughly 8 Liters Water Mixture weight: 1.80 kg/lt Application temperature: +5 ºC ºC ΡΗ mixture: >10 Self life in bucket: Approximately 1 hour Application width: mm Consumption: Plastering: 8-10 kg/m² depending on use Building: 6-7 kg/ m² for 10cm masonry 20 kg/ m² for 20cm masonry Waiting time for finishing coating: 7 days for summer season and 14 days for winter season Strengths: Flexibility: No Shrinking: No Acids-Alkali: Excellent Humidity: Excellent Adhesion strength (28 days): 0.3 N/mm² -FP:A Compressive strength (28 days): CSIV Thermal Conductivity λ 10, dry : 0.7 W/m.K given table value Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 84

94 Declaration of Performance: No.: AP CPR - 01/07/ Unique identification code of the product-type: PITTAKIS CEM Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Performance Reaction to fire Class Α1 Adhesion 0.3 Ν/mm 2 - FΡ: A Compressive Strength CSIV Water Absorption W1 Water Vapour permeability coefficient μ 18 Dry Bulk Density 1700 kg/m 3 Thermal Conductivity, λ 10, dry 0.7 W/m K for Ρ=50% Harmonised Technical Specification ΕΝ 998-1: 2010 Durability (against freeze/thaw) Evaluation based on provisions valid in the intended place of use of the mortar. 10. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

95 Declaration of Performance: No.: AP CPR - 01/07/ Unique identification code of the product-type: PITTAKIS CEM Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: Prescribed general purpose masonry mortar for external use in elements subject to structural requirements. 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-2: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Cement (mass percent) 20% Lime (mass percent) 9% Aggregates (mass percent) 71% Performance Harmonised Technical Specification Contents of chloride Reaction to fire 0.01% Cl Class Α1 ΕΝ 998-1: 2010 Water Absorption 0.35 kg/m 2.min 0.5 Water Vapour permeability coefficient μ 18 Thermal Conductivity, λ 10, dry Durability (against freeze/thaw) 0.7 W/m K for Ρ=50% Evaluation based on provisions valid in the intended place of use of the mortar. 10. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

96 THERMOPILOS THERMOPILOS is ready pre-mixed plaster based on expanded perlite, cement, lime and sand. Is reinforced with polymeric fibres and quality enhancing additives, that gives thermal insulation, fire resistance, and acoustic effect. Suitable for a wide variety of applications, internal and external use as 1 st and 2 nd hand plaster on blocks, thermal insulating bricks - Climalite, Ytong, UB200, Fair Face (only if the surface has treated properly with a primer), cement plaster and polysterine (if first is applied adhesive with fibre net and 1 st hand plaster) and for building bricks. Mixture, Preparation of sub layer and examples of enforcements: 1. All required water is placed in a drum or in a concrete mixer. 2. For mixing with concrete mixer THERMOPILOS is added as the concrete mixer is rotated. Mixing should continue until the slurry is uniform. Do not exceed a mixing time of more than five minutes. When mixing by hand add half the contents of the bag in the water and mix. Then add the remainder of the bag and mix (add more water if required) to obtain the correct consistency. 3. Let the composition stand for 5 minutes and mix again for half minute. 4. Use the plaster mixture within ½ hour from mixing. Do not leave the mixture unmixed for a long time. A fast way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then mixture can be used. 5. After a while do not mix or add water because of some negative mechanical strength. Application: 1. All surfaces should be thoroughly cleaned to remove dust loose particles, grease and traces of foreign materials. Thoroughly wet all areas especially the areas with high water absorption. 2. The substrate has to be flat without any anomalies for better final appliance. 3. THERMOPILOS should be applied in one coat between 20-30mm thick. Additional coats can be applied if a greater thickness is required. 4. To assure proper cement hydration, the basecoat plaster should be kept damp for at least 2-3 days. 5. After the basecoat has been allowed to dry at least 7 days in summer, and 14 days in winter, finish materials may be applied. THERMOPILOS is compatible with most building materials. The surface can be covered with all Paralimnitiko plasters or ALFAKOL adhesives. For the final coat is recommended to use Smartplast fine granulated or Extra Plast kg sack covers approximately 1 m 2 of plastering with thickness 22mm always under normal conditions. Warning: Avoid the application of THERMOPILOS at high sun shines, temperatures and also hot wind. As result, is to avoid cracks during the period of dryness and maturation of the surface. The plastered surface has to stay so it absorbs for at least 7 days in summer, and 14 days in winter, so the cracks can be covered with the next plaster. 87

97 Technical characteristics: THERMOPILOS: Product definition: Type: Powder Granulometry: mm Colour: Grey Specific Gravity: 1.40 kg/lt Composition of dry materials: 100% Storage: 9 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use : Composition of mixture: Thick Water requirements: 25kg Powder with roughly 6-8 Liters Water Application temperature: +5 ºC ºC ΡΗ mixture: >10 Self life in bucket: Approximately 1 hour Application width: mm Plastering: 25kg/m² for application thickness Consumption: 18-20mm, depending use/surface Building: 5-6 kg/ m² for 10cm masonry 20 kg/ m² for 25cm masonry Waiting time for finishing coating: 7 days for summer season and 14 days for winter season Strengths: Flexibility: No Shrinking: No Acids-Alkali: Excellent Humidity: Excellent Adhesion strength (28 days): 0.3 N/mm² - FP:A Flexural strength (after 28 days) 2.7 N/mm² Compressive strength (after 28 days) CSIII Thermal conductivity λ 10, dry 0,29W/mK (tab. Mean value, P=50%) Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 88

98 Declaration of Performance: No.: AP080-1 CPR - 01/07/ Unique identification code of the product-type: THERMOPILOS Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: Light Weight Mortar (LW) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 0.3 Ν/mm 2 - FΡ: A CSIII Water Absorption W1 Water Vapour permeability coefficient μ 6 Dry Bulk Density <1300 kg/m 3 Thermal Conductivity, λ 10, dry 0.29 W/m K for Ρ=50% Harmonised Technical Specification ΕΝ 998-1: 2010 Durability (against freeze/thaw) Evaluation based on provisions valid in the intended place of use of the mortar. 10. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

99 Declaration of Performance: No.: AP080-2 CPR - 01/07/ Unique identification code of the product-type: Thermopilos Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: Prescribed general purpose masonry mortar for external use in elements subject to structural requirements. 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-2: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Cement (mass percent) 15% Lime (mass percent) 6% Aggregates (mass percent) 79% Performance Harmonised Technical Specification Contents of chloride Reaction to fire 0.01% Cl Class Α1 ΕΝ 998-2: 2010 Water Absorption 0.3 kg/m 2.min 0.5 Water Vapour permeability coefficient μ 6 Thermal Conductivity, λ 10, dry Durability (against freeze/thaw) 0.29 W/m K for Ρ=50% Evaluation based on provisions valid in the intended place of use of the mortar. 10. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

100 ALFAREP ALFAREP is one component, cementitious pre-bagged, ready to use REPAIR Mortar, with NO LIME. When mixed with the correct amount of water, it produces a thixotropic, high strength repair mortar, reinforced with acrylic fibres. ALFAREP has very low permeability and is suitable for repairing concrete elements and generally wherever high strength is necessary. Instructions for use: Surface preparation: The substrate must be flat and clean from dust or oils. For better adhesion Thorough dampening of the substrate before application is necessary. Weak or damaged concrete shall be removed. All the concrete steel structure should be cleaned from rust and after to be primed with a special primer for the protection of iron. Mixing: Add 25kg ALFAREP to 5 6 L water. Mix in a concrete machine or with an electrical mixer until a smooth uniform mix is produced, leave the mixture to stand for about 5 minutes and mix again. After the product begins to set do not add any water because of negative mechanical strengths. Application: The substrate is cleaned and moistened. While the surface is still damp, ALFAREP can be applied by spraying machine or hand troweling, in thicknesses up to 20 mm in one layer. Greater thicknesses can be achieved by applying more than one layer. When applying by hand ALFAREP must be forced tightly into the substrate to ensure intimate contact with the pre-wetted substrate. Final finishing should be carried out using a steel float. Surfaces should be wetted for 2-3 days. Weather Conditions: Use at temperatures between +5 o C and +40 o C. Too high or too low temperatures, it might cause a negative reaction to the product. Storage: Store out of direct sunlight, clear of the ground on pallets, protect from rainfall. Avoid excessive compaction. Shelf life is 9 months when stored as above. 91

101 Technical characteristics (typical values): ΑLFA REP Product Identity Consistency: Powder containing fibres Colour: Grey Dry Solid content (%): 100% Storage: 9 months in a dry place in original unopened packaging Granulometry: mm Package & Weight: Bags of 25kg Toxicity / Inflammability: No Application data Consistency of mix: Paste Mix Ratio: 25kg Powder with 5-6 Liters Water Wet density: 1.95 kg/lt Application temperature range: +5 ºC ºC pη of the mix: >10 Pot Life: 30 minutes Application Thickness: mm Consumption: 25 kg/m² per 18mm of thickness Final Performances Results R4 Requirments (ΕΝ1504-3) Shrinkage: No Chloride ion contents: 0.01% < 0.05 % Reaction to fire: Α1 Adhesive Bond (28 days) 2.7 N/mm² > 2 N/mm² (MPa) Compressive Strength (28 days) 73 N/mm² > 45 N/mm² (MPa) Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information, contact with AVRAAM PITTAKIS and SONS LTD. 92

102 CONSTRUCTION MATERIALS PRODUCERS COMPOUNDS & TEXTURED COATING COMPOUNDS & TEXTURED COATING

103 Compounds SERIES WALL LEVELING COMPOUNDS FOR THE FINAL COATING

104 FLASHELASTIC SPA THICK ACRYLIC Flash Spa Flexible Acrylic thick granulated is a super strength wall leveling compound based on cement, lime, white powder and other various chemical addictives. Ideal for the coating of indoor and outdoor areas, from cement plaster, Fair Face beton, and for surfaces of 2 nd and 3 rd hand coat, whether painted or not. Also, ideal for applications near to beaches. Mixture, Preparation of sub layer and examples of enforcements: 1. We add clean water into an empty container or a concrete mixer. 2. We place into the empty container or the concrete mixer, first the water and after the material one by one. 3. The mixture is made with an electric mixer or a concrete mixer, mixing at low speed until the material becomes a smooth mass. We leave the mixture to mature for 5 minutes and then we mix again. 4. We use the mixture when it is still fresh, and we continue carefully the above instruction. We do not leave the mixture unmixed for a long time. A fast way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then we can use the mixture. 5. The mixture can be stored in the container for 4 hours, provided that we stir again. 6. After a while we do not mix or add water because of some negative mechanical strength. Application: 1. The surface which will the mixture be applied has to be clean from dust, any other material, or oil and has to be sprinkled with water well before use. 2. The substrate has to be flat without any anomalies for better final appliance. 3. When the surface has a big absorption then good sprinkling of the surface is needed. 4. The layer can be done with a spatula in 2 layers or more. The time between the layers must be at least 1-12 hours, proportionally with the temperature or the layer. 5. Leave at least 12 hours the final layer to dry and after it can be anchored with sandpaper. The surface can be decorated with many kinds of coatings such as texture finishes Pittakis Grafit, Flash Spa compound, emulsion paints, oil paints, acrylic paints and wall paper. Warning: We avoid the application of Flash Spa at high sun shines, temperatures and also hot wind. As result, is to avoid cracks during the period of dryness and maturation of the surface. 93

105 Technical characteristics: Flashelastic Spa Thick Granulated Acrylic: Product definition: Type: Powder Granulometry: mm Colour: Grey and White Specific Gravity: 1.30 kg/lt Composition of dry materials: 100% Storage: 8 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use : Composition of mixture: Thick Water requirements: 25kg Powder with roughly 8 Liters Water Mixture weight: 1.55 kg/lt Application temperature: +5 ºC ºC ΡΗ mixture: >10 Self life in bucket: 4 hours/mix every 1 hour Application width: 1-2 mm Consumption: 2 kg/m² depending use/surface Time of maturing: 14 days Strengths: Flexibility: Shrinking: Acids-Alkali: Humidity: Adhesion Strength (28 days): Compressive Strength (28 days): Thermal Conductivity (λ10,dry): Yes No Excellent Excellent 0.7 N/mm² - FP:B 3.6 N/mm 2 CSIII 0.4W/m.K standard table value Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 94

106 Declaration of Performance: No.: AP011 CPR - 01/07/ Unique identification code of the product-type: FLASHELASTIC SPA THICK Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 0.7 Ν/mm 2 - FΡ: B CSIII Water Absorption W1 Water Vapour permeability coefficient μ 6 Dry Bulk Density 1300 kg/m 3 Thermal Conductivity λ 10, dry Durability (against freeze/thaw) 0.4 W/m K for Ρ=50% Evaluation based on provisions valid in the intended place of use of the mortar. Harmonised Technical Specification ΕΝ 998-1: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

107 FLASH SPA THICK Flash Spa thick granulated is a super strength wall leveling compound based on cement, lime, white powder and other various chemical addictives. Ideal for the coating of indoor and outdoor areas, from Fair Face beton or 2 nd and 3 rd hand coat. Mixture, Preparation of sub layer and examples of enforcements: 1. We add clean water into an empty container or a concrete mixer. 2. We place into the empty container or the concrete mixer, first the water and after the material one by one. 3. The mixture is made with an electric mixer or a concrete mixer, mixing at low speed until the material becomes a smooth mass. We leave the mixture to mature for 5 minutes and then we mix again. 4. We use the mixture when it is still fresh, and we continue carefully the above instruction. We do not leave the mixture unmixed for a long time. A fast way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then we can use the mixture. 5. The mixture can be stored in the container for 4 hours, provided that we stir again. 6. After a while we do not mix or add water because of some negative mechanical strength. Application: 1. The surface which will the mixture be applied has to be clean from dust, any other material, or oil and has to be sprinkled with water well before use. 2. The substrate has to be flat without any anomalies for better final appliance. 3. When the surface has a big absorption then good sprinkling of the surface is needed. 4. The layer can be done with a spatula in 2 layers or more. The time between the layers must be at least 1-12 hours, proportionally with the temperature or the layer. 5. Leave at least 12 hours the final layer to dry and after it can be anchored with sandpaper. The surface can be decorated with many kinds of coatings such as texture finishes Pittakis Grafit, Flash Spa compound, emulsion paints, oil paints, acrylic paints and wall paper. Warning: We avoid the application of Flash Spa at high sun shines, temperatures and also hot wind. As result, is to avoid cracks during the period of dryness and maturation of the surface. 96

108 Technical characteristics: Flash Spa thick granulated: Product definition: Type: Powder Granulometry: mm Colour: Grey and White Specific Gravity: 1.30 kg/lt Composition of dry materials: 100% Storage: 8 months in a dry place, closed sealed sack Package & Weight: Bags of 10kg & 25kg Toxicity / Inflammability: No Elements of use : Composition of mixture: Thick Water requirements: 25kg Powder with roughly 8 Liters Water Mixture weight: 1.55 kg/lt Application temperature: +5 ºC ºC ΡΗ mixture: >10 Self life in bucket: 4 hours/mix every 1 hour Application width: 1-2 mm Consumption: 2 kg/m² depending use/surface Time of maturing: 14 days Strengths: Flexibility: No Shrinking: No Acids-Alkali: Excellent Humidity: Excellent Resistance in the welding (28 days): 0.3 N/mm² - FP:B Resistance in the bending (28 days): 2.4 N/mm 2 Resistance to compression (28 days): 5 N/mm² - CSIII Water Absorption: W0 Thermal Conductivity (λ10,dry) 0.4 W/m.K given table value Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 97

109 Declaration of Performance: No.: AP028 CPR - 01/07/ Unique identification code of the product-type: FLASH SPA THICK Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 0.3 Ν/mm 2 - FΡ: B CSIII Water Absorption W0 Water Vapour permeability coefficient μ 19 Dry Bulk Density 1300 kg/m 3 Thermal Conductivity λ 10, dry 0.4 W/m K for Ρ=50% Harmonised Technical Specification ΕΝ 998-1: 2010 Durability (against freeze/thaw) Evaluation based on provisions valid in the intended place of use of the mortar. 10. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

110 FLASHELASTIC SPA FINE ACRYLIC Flash Spa Flexible Acrylic fine granulated is a super strength wall leveling compound based on cement, lime, white powder and other various chemical addictives. Ideal for the coating of indoor and outdoor areas, from cement plaster, Fair Face beton, and for surfaces of 2 nd and 3 rd hand coat, whether painted or not. Also, ideal for applications near to beaches. Mixture, Preparation of sub layer and examples of enforcements: 1. We add clean water into an empty container or a concrete mixer. 2. We place into the empty container or the concrete mixer, first the water and after the material one by one. 3. The mixture is made with an electric mixer or a concrete mixer, mixing at low speed until the material becomes a smooth mass. We leave the mixture to mature for 5 minutes and then we mix again. 4. We use the mixture when it is still fresh, and we continue carefully the above instruction. We do not leave the mixture unmixed for a long time. A fast way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then we can use the mixture. 5. The mixture can be stored in the container for 4 hours, provided that we stir again. 6. After a while we do not mix or add water because of some negative mechanical strength. Application: 1. The surface which will the mixture be applied has to be clean from dust, any other material, or oil and has to be sprinkled with water well before use. 2. The substrate has to be flat without any anomalies for better final appliance. 3. When the surface has a big absorption then good sprinkling of the surface is needed. 4. The layer can be done with a spatula in 2 layers or more. The time between the layers must be at least 6-12 hours, proportionally with the temperature or the layer. 5. Leave at least 24 hours the final layer to dry and after it can be anchored with sandpaper. The surface can be decorated with many kinds of coatings such as texture finishes Pittakis Grafit, Flash Spa compound, emulsion paints, oil paints, acrylic paints and wall paper. Warning: We avoid the application of Flash Spa at high sun shines, temperatures and also hot wind. As result, is to avoid cracks during the period of dryness and maturation of the surface. 99

111 Technical characteristics: Flashelastic Spa Fine granulated Acrylic: Product definition: Type: Powder Granulometry: mm Colour: Grey and White Specific Gravity: 1.20 kg/lt Composition of dry materials: 100% Storage: 8 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use : Composition of mixture: Thick Water requirements: 25kg Powder with roughly 8 Liters Water Mixture weight: 1.45 kg/lt Application temperature: +5 ºC ºC ΡΗ mixture: >10 Self life in bucket: 4 hours/mix every 1 hour Application width: 1 mm Consumption: 2 kg/m² depending use/surface Time of maturing: 14 days Strengths: Flexibility: Shrinking: Acids-Alkali: Humidity: Adhesion Strength (28 days): Compressive Strength (28 days): Thermal Conductivity (λ10,dry): Yes No Excellent Excellent 0.6 N/mm² - FP:B 5.3 N/mm 2 CSIII 0.4W/m.K standard table value Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 100

112 Declaration of Performance: No.: AP023 CPR - 01/07/ Unique identification code of the product-type: FLASHELASTIC SPA FINE Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 0.6 Ν/mm 2 - FΡ: B CSIII Water Absorption W1 Water Vapour permeability coefficient μ 6 Dry Bulk Density 1200 kg/m 3 Thermal Conductivity, λ 10, dry Durability (against freeze/thaw) 0.4 W/m K for Ρ=50% Evaluation based on provisions valid in the intended place of use of the mortar. Harmonised Technical Specification ΕΝ 998-1: The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

113 FLASH SPA FINE Flash Spa fine granulated is a super strength wall leveling compound based on cement, lime, white powder and other various chemical addictives. Ideal for the coating of indoor and outdoor areas, from Fair Face beton or 2 nd and 3 rd hand coat. Mixture, Preparation of sub layer and examples of enforcements: 1. We add clean water into an empty container or a concrete mixer. 2. We place into the empty container or the concrete mixer, first the water and after the material one by one. 3. The mixture is made with an electric mixer or a concrete mixer, mixing at low speed until the material becomes a smooth mass. We leave the mixture to mature for 5 minutes and then we mix again. 4. We use the mixture when it is still fresh, and we continue carefully the above instruction. We do not leave the mixture unmixed for a long time. A fast way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then we can use the mixture. 5. The mixture can be stored in the container for 4 hours, provided that we stir again. 6. After a while we do not mix or add water because of some negative mechanical strength. Application: 1. The surface which will the mixture be applied has to be clean from dust, any other material, or oil and has to be sprinkled with water well before use. 2. The substrate has to be flat without any anomalies for better final appliance. 3. When the surface has a big absorption then good sprinkling of the surface is needed. 4. The layer can be done with a spatula in 2 layers or more. The time between the layers must be at least 6-12 hours, proportionally with the temperature or the layer. 5. Leave at least 24 hours the final layer to dry and after it can be anchored with sandpaper. The surface can be decorated with many kinds of coatings such as texture finishes Pittakis Grafit, Flash Spa compound, emulsion paints, oil paints, acrylic paints and wall paper. Warning: We avoid the application of Flash Spa at high sun shines, temperatures and also hot wind. As result, is to avoid cracks during the period of dryness and maturation of the surface. 102

114 Technical characteristics: Flash Spa fine granulated: Product definition: Type: Powder Granulometry: mm Colour: Grey and White Specific Gravity: 1.20 kg/lt Composition of dry materials: 100% Storage: 8 months in a dry place, closed sealed sack Package & Weight: Bags of 10kg & 25kg Toxicity / Inflammability: No Elements of use : Composition of mixture: Thick Water requirements: 25kg Powder with roughly 8 Liters Water Mixture weight: 1.45 kg/lt Application temperature: +5 ºC ºC ΡΗ mixture: >10 Self life in bucket: 4 hours/mix every 1 hour Application width: 1 mm Consumption: 2 kg/m² depending use/surface Time of maturing: 14 days Strengths: Flexibility: Shrinking: Acids-Alkali: Humidity: Resistance in the welding (28 days): Resistance in the bending (28 days): Resistance to compression (28 days): Water Absorption: Thermal Conductivity (λ10,dry) No No Excellent Excellent 0.3 N/mm² - FP:B 1.9 N/mm² CSIII W1 0.4 W/m.K given table value Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 103

115 Declaration of Performance: No.: AP031 CPR - 01/07/ Unique identification code of the product-type: FLASH SPA FINE Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: General Purpose Plastering Mortar (GP) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 0.3 Ν/mm 2 - FΡ: B CSIII Water Absorption W1 Water Vapour permeability coefficient μ 18 Dry Bulk Density 1200 kg/m 3 Thermal Conductivity, λ 10, dry 0.4 W/m K for Ρ=50% Harmonised Technical Specification ΕΝ 998-1: 2010 Durability (against freeze/thaw) Evaluation based on provisions valid in the intended place of use of the mortar. 10. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4 Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

116 Textured Coating SERIES TEXTURED COATING FOR FINAL COATING ON 2 ND HAND PLASTER & FAIR FACE BETON

117 PITTAKIS GRAFIT The prefabricating Pittakis grafit is a coating in different colours with base the white cement, powder and other various chemical addictives. Ideal for coating on plastered surfaces 2nd hand, Fair Face and beton. Mixture, Preparation of sub layer and examples of enforcements: 1. We add clean water into an empty container or a concrete mixer. 2. We place into the empty container or the concrete mixer, first the water and after the material one by one. 3. The mixture is made with an electric mixer or a concrete mixer, mixing at low speed until the material becomes a smooth mass. We leave the mixture to mature for 5 minutes and then we mix again. 4. We use the mixture when it is still fresh, and we continue carefully the above instruction. We do not leave the mixture unmixed for a long time. A fast way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then we can use the mixture. 5. The mixture can be stored in the container for a maximum of 1/2 hour after the mix. 6. After a while we do not mix or add water because of some negative mechanical strength. Appliance: 1. The surface which will the mixture be applied has to be clean from dust, any other material, or oil and has to be sprinkled with water well before use. 2. The substrate has to be flat without any anomalies for better final appliance. 3. When the surface has a big absorption then good sprinkling of the surface is needed. 4. It is used as coating different stonework from 2nd hand, fair face and beton. 5. It is applied the thin layer in 3-5mm, the medium in 6-8mm and the thick layer in 8-10mm. 6. A sack of 25kg covers approximately 3-4kg/m 2, always under physiological conditions. 105

118 Technical characteristics: Pittakis grafit: Product definition: Type: Powder Granulometry: 0 3 mm (with or without grafit) Colour: 8 different colours Specific Gravity: 1.50 kg/lt Composition of dry materials: 100% Storage: 12 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use : Composition of mixture: Thick Water requirements: 25kg Powder with roughly 7 Liters Water Mixture weight: 1.80 kg/lt Application temperature: +5 ºC ºC ΡΗ mixture: >10 Self life in bucket: Approximately 1 hour Application width: Thin, medium, thick layer Consumption: 3-5 kg/m² depending use/surface Time of maturing: 14 days Strengths: Flexibility: Shrinking: Acids-Alkali: Humidity: No No Excellent Excellent Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 106

119 PARALIMNITIKO MIXED SPRITS The prefabricated ready sprits is a coat with base the white cement, powder and various chemical additives. Ideal for coating on plastered surfaces of 2nd hand. Mixture, Preparation of sub layer and examples of enforcements: 1. We add clean water into an empty container or a concrete mixer. 2. We place into the empty container or the concrete mixer, first the water and after the material one by one. 3. The mixture is made with an electric mixer or a concrete mixer, mixing at low speed until the material becomes a smooth mass. We leave the mixture to mature for 5 minutes and then we mix again. 4. We use the mixture when it is still fresh, and we continue carefully the above instruction. We do not leave the mixture unmixed for a long time. A fast way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then we can use the mixture. 5. The mixture can be stored in the container for a maximum of 1 hour after the mix. 6. After a while we do not mix or add water because of some negative mechanical strength. Appliance: 1. The surface which will the mixture be applied has to be clean from dust, any other material, or oil and has to be sprinkled with water well before use. 2. The substrate has to be flat without any anomalies for better final appliance. 3. When the surface has a big absorption then good sprinkling of the surface is needed. 4. It can be used as a plaster of different wall bricks of 2 nd hand. 5. A 25kg sack covers approximately 4-5 kg/m 2, always under physiologic conditions. 107

120 Technical characteristics: Ready Mixed Sprits: Product definition: Type: Powder Granulometry: mm Colour: White or beige Specific Gravity: 1.50 kg/lt Composition of dry materials: 100% Storage: 12 months in a dry place, closed sealed sack Package & Weight: Bags of 25kg Toxicity / Inflammability: No Elements of use : Composition of mixture: Thick Water requirements: 25kg Powder with roughly 8 Liters Water Mixture weight: 1.80 kg/lt Application temperature: +5 ºC ºC ΡΗ mixture: >10 Self life in bucket: Approximately 1 hour Application width: 4-6 mm Consumption: 4-5 kg/m² depending use/surface Time of maturing: 14 days Strengths: Flexibility: Shrinking: Acids-Alkali: Humidity: No No Excellent Excellent Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 108

121 ALFALIQ UV THERMAL - Acrylic ALFA UV THERMAL Acrylic is a ready to use thick pasty, extra white acrylic, scratch effect plaster. It consists of aggregate with a special particle size granulation, to form a coarse-textured decorative surface. It's used to protect and decorate exterior and interior surfaces (plaster, concrete, facade thermal insulation systems). Benefits: Excellent adhesion and alkaline resistance Excellent workability-fast application Highly resistance to UV rays and ageing Cracking prevention High water repellency and Excellent vapor permeability Suitable for indoor and outdoor application Instructions for use: Surface preparation: Substrate must be dry, free of dust or loose particles etc. Prime the surface with ALFA GRAFIT PRIMER (in the same colour with graffiato) prior application. Application: ALFA UV THERMAL Acrylic is applied after the primer has dried completely (max 24 hours after primer application). Stir well before application. Stirring should be done with slow circular motions in order to avoid creating bubbles in the mass of the material. Plaster is applied by hand using a stainless or plastic trowel. While is still fresh the plaster is treated (pressed) by plastic float, in horizontal, vertical or circular movements depending on the desirable appearance of the surface Protect the plastered surface from high temperatures, rain and frost until is cured (about 24 hours). Weather Conditions: Use at temperatures between +5 o C and +35 o C. Too high or too low temperatures, it might cause a negative reaction to the product. Consumption: kg/m 2 Packaging: Buckets of 5kg, 10kg & 25kg Storage: 12 months if stored in original, unopened packaging, in a dry place. Protect from direct sun exposure and freezing weather. 109

122 Technical characteristics (typical values): ALFA UV THERMAL - Acrylic Product Identity Appearance: Paste Granulometry: < 1.8 mm / < 2.5mm Colour: 8 standard colors or custom color Density: kg/l (according to the grain size) Dry Solids content (%): % Shelf Life-Storage: 12 months from production date Toxicity: No Application Data Preparation: Ready to use Application temperature range: +5 ºC ºC Consumption: kg/m 2 Drying: In open air Ready for painting: About 1-2 days Performance Characteristics according ΕΝ Textured Coatings for Internal and External Use based on Organic Binders Adhesion - ΕΝ N/mm² Water absorption ΕΝ Class W3 (w < 0.1 kg/m 2.min 0.5 ) Water Vapour Permeability Class V2, medium (0.14 m < Sd < 1.4 m) ΕΝ ISO Thermal Conductivity EN W/m.K standard table value Reaction to Fire ΕΝ Α2-S1,d0 1 B-S1,d0 2 1 ETICS with stone wool 2 ETICS with XPS Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information, contact with AVRAAM PITTAKIS and SONS LTD. 110

123 ALFALIQ UV THERMAL-Silicone ALFALIQ UV THERMAL-Silicone is a ready to use thick pasty, acrylic-silicone, scratch effect plaster. It consists of aggregate with a special particle size granulation, to form a flat finish (1mm) or a coarse-textured decorative surface (< 1.5 mm & < 2.8 mm). Due to its high elasticity and its excellent bonding to the surface ALFALIQ UV THERMAL is an ideal final coat for external thermal-insulated facades. It's also used to protect and decorate exterior and interior surfaces (plaster, concrete, cement and gypsum boards). Εliminates the need of facade painting. Benefits: Excellent adhesion and alkaline resistance Excellent workability-fast application Highly resistance to UV rays and ageing Cracking prevention High water repellency and Excellent vapor permeability Suitable for indoor and outdoor application Instructions for use: Surface preparation: Substrate must be dry, free of dust or loose particles etc. Prime the surface with ALFALIQ GRAFIT PRIMER (in the same colour with graffiato) or ALFALIQ PRIMER, prior application. Application: ALFA UV THERMAL-Silicone is applied after the primer has dried completely (max 24 hours after primer application). Stir well before application. Stirring should be done with slow circular motions in order to avoid creating bubbles in the mass of the material. Plaster is applied by hand using a stainless or plastic trowel. While is still fresh the plaster is treated (pressed) by plastic float, in horizontal, vertical or circular movements depending on the desirable appearance of the surface Protect the plastered surface from high temperatures, rain and frost until is cured (about 24 hours). Weather Conditions: Use at temperatures between +5 o C and +35 o C. Too high or too low temperatures, it might cause a negative reaction to the product. Consumption: kg/m 2 Packaging: 5kg / 10kg / 25 kg buckets Storage: 12 months if stored in original, unopened packaging, in a dry place. Protect from direct sun exposure and freezing weather. 111

124 Technical characteristics (typical values): ALFA UV THERMAL-Silicone Product Identity Appearance: Paste Granulometry: < 1 mm (flat finish) < 1.5 mm & < 2.8 mm (graffiato) Colour: 8 standard colors or custom color Density: kg/l (according to the grain size) Dry Solids content (%): % Shelf Life-Storage: 12 months from production date Toxicity: No Application Data Preparation: Ready to use Application temperature range: +5 ºC ºC Consumption: kg/m 2 Drying: In open air Ready for painting: About 1-2 days Performance Characteristics according ΕΝ Textured Coatings for Internal and External Use based on Organic Binders Adhesion - ΕΝ N/mm² Water absorption ΕΝ Class W3 (w < 0.1 kg/m 2.min 0.5 ) Water Vapour Permeability Class V1, High (Sd 0.14 m) ΕΝ ISO Thermal Conductivity EN W/m.K Standard table value Reaction to Fire ΕΝ Α2-S1,d0 1 B-S1,d0 2 Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information, contact with AVRAAM PITTAKIS and SONS LTD. 112

125 ALFALIQ GRAFIT ALFALIQ GRAFIT is a ready to use thick pasty, white or colored acrylic, scratch effect plaster. It consists of aggregate with a special particle size granulation, to form a flat finish (1mm) or a coarse-textured decorative surface (< 1.5 mm & < 2.8 mm). It's used to protect and decorate exterior and interior surfaces (plaster, concrete, cement and gypsum boards). Εliminates the need of facade painting. Benefits: Excellent adhesion and alkaline resistance Excellent workability-fast application Highly resistance to UV rays and ageing Cracking prevention High water repellency and Excellent vapor permeability Suitable for indoor and outdoor application Instructions for use: Surface preparation: Substrate must be dry, free of dust or loose particles etc. Prime the surface with ALFALIQ GRAFIT PRIMER (in the same colour with graffiato) or ALFALIQ PRIMER, prior application. Application: ALFALIQ GRAFIT is applied after the primer has dried completely (max 24 hours after primer application). Stir well before application. Stirring should be done with slow circular motions in order to avoid creating bubbles in the mass of the material. Plaster is applied by hand using a stainless or plastic trowel. While is still fresh the plaster is treated (pressed) by plastic float, in horizontal, vertical or circular movements depending on the desirable appearance of the surface Protect the plastered surface from high temperatures, rain and frost until is cured (about 24 hours). Weather Conditions: Use at temperatures between +5 o C and +35 o C. Too high or too low temperatures, it might cause a negative reaction to the product. Consumption: kg/m 2 Packaging: 5kg / 10kg / 25 kg buckets Storage: 12 months if stored in original, unopened packaging, in a dry place. Protect from direct sun exposure and freezing weather. 113

126 Technical characteristics (typical values): ALFALIQ GRAFIT Product Identity Appearance: Paste Granulometry: < 1 mm (flat finish) < 1.5 mm & < 2.8 mm (graffiato) Colour: 8 standard colors or custom color Density: kg/l (according to the grain size) Dry Solids content (%): % Shelf Life-Storage: 12 months from production date Toxicity: No Application Data Preparation: Ready to use Application temperature range: +5 ºC ºC Consumption: kg/m 2 Drying: In open air Ready for painting: About 1-2 days Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information, contact with AVRAAM PITTAKIS and SONS LTD. 114

127 CONSTRUCTION MATERIALS PRODUCERS INSULATION MATERIALS & SELF LEVELING COMPOUNDS INSULATION MATERIALS & SELF LEVELING COMPOUNDS

128 THERMAL INSULATION SERIES THERMAL INSULATION PRODUCTS - PERLOBETON - THERMOSOVAS

129 PERLOBETON PERLOBETON is ready pre-mixed, lightweight mortar based on expanded perlite, cement and sand. Is reinforced with polymeric fibres and quality enhancing additives, that give thermal insulation, fire resistance, and acoustic effect. Suitable for internal or external use, for leveling flat roofs, or on thermal insulating panels if first is applied adhesive with fibre net. Mixture, Preparation of sub layer and examples of enforcements: 1. Pour the material into clean water and mix in a concrete machine until a homogeneous lump free mix is obtained. Also Spraying machine can be used. 2. Mixing time should not exceed 5 minutes because it might cause adverse effect on its mechanical properties. 3. Allow the mix to cure for 5 minutes and periodically repeat stirring. 4. Use the mixture within ½ hour from mixing - while is still fresh. Do not leave the mix unmixed for a long time. An easy way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then mixture can be used. 5. Do not mix with water or latex additive when the mixture starts to set in the bucket. In such case the mix should be dropped. Application procedure: 1. The base concrete surface should be structurally sound and free from excessive dust, dirt and contaminants such as oil and grease. 2. To properly clean the surface, the whole area should be brushed over with a stiff bristle broom and water. 3. After you place the guides apply Perlobeton to the desire thickness (up to 8-10 cm), by a plaster spraying machine or by hand using convectional tools for screed laying. Greater thicknesses (up to 15cm) can be achieved by applying more than one layer, after the first layer is almost dry. 4. The surface should be lightly dampened, for 2 3 days, beginning 24 hours after application, especially in hot weather, with intense evaporation. 5. One bag covers approximately 1 m 2 of plastering with thickness 22mm always under normal conditions. 6. The plastered surface can be decorated with a wide range of Paralimnitiko products (such as plasters, texture coatings, adhesives), paint e.t.c. Warning: Avoid the application of THERMOPILOS at high sun shines, temperatures and also hot wind. As result, is to avoid cracks during the period of dryness and maturation of the surface. The plastered surface has to stay so it absorbs for at least 7 days in summer, and 14 days in winter, so the cracks can be covered with the next plaster. 115

130 Technical characteristics: PERLOBETON Product definition: Type: Powder Granulometry: mm Colour: Grey Composition of dry materials: 100% Storage: 6 months in a dry place, closed sealed sack Package & Weight: Bags of 25Lt Toxicity / Inflammability: No Application data: Consistency of mix: Thick Water demand: 20L Powder with roughly 15 LWater Application temperature: +5 ºC ºC ΡΗ mixture: >10 Pot life: Approximately 1/2 hour Application thickness: cm Consumption: 20 L / m² for application thickness 25mm depending use/surface Strengths: Shrinking: Acids-Alkali: Humidity: Adhesion strength (after 28 days) Compressive strength (after 28 days) Thermal conductivity (λ10, dry) No Excellent Excellent 0.3 Ν/mm 2 FP:B CSII class T1- λ 0.1 W/m K Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 116

131 Declaration of Performance: No.: AP121 CPR - 01/07/ Unique identification code of the product-type: PERLOBETON Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: Thermal Insulating Mortar (T) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 0.3 Ν/mm 2 - FΡ: B CSII Water Absorption W0 Water Vapour permeability coefficient μ 6 Dry Bulk Density 510 kg/m 3 Harmonised Technical Specification ΕΝ 998-1: 2010 Thermal Conductivity, λ 10, dry Durability (against freeze/thaw) class Τ1- λ 0.1 W/m K Evaluation based on provisions valid in the intended place of use of the mortar. 10. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

132 118

133 THERMOSOVAS THERMOSOVAS is a mixed thermal lightweight plaster, based on expanded perlite, grey cement, lime and its reinforced with polymeric fibers. The various chemical additives and the expanded perlite give a perfect thermal insulation, fire resistance, and improves sound insulation. Ideal for internal and external use, on fair face, as a 2 nd hand plaster on bricks, blocks or thermal insulated bricks, YTONG and Climalite Daliko and Polysterine( if first we applied adhesive with fiber net and 1 st hand plaster). An ideal underlayment for paints, decorative plasters and wallpapers Mixture, Preparation of sub layer and examples of enforcements: 1. We add clean water into an empty container or a concrete mixer. 2. We place into the empty container or the concrete mixer, first the water and after the material one by one. 3. Prepare the plaster by adding THERMOSOVAS to a measured amount of clean water. It can be mixed by mechanical mixer or in a concrete mixer. The mixing period it should not be more than 4-5 minutes. Use the plaster mixture within ½ hour from mixing. 4. After a while we do not mix or add water because of some negative mechanical strength. 5. We use the mixture when it is still fresh, and we continue carefully the above instruction. We do not leave the mixture unmixed for a long time. A fast way to check if the mixture is still fresh is to touch with two fingers on the surface and if the two fingers are sticky, then we can use the mixture. 6. The mixture can be stored in the bucket for a maximum of 1/2 hour after the mix. Application: 1. The surface has to be clean from dust, loose particles, grease and traces of foreign materials. and has to be sprinkled with water well before use. 2. The substrate has to be flat without any anomalies for better final appliance. 3. When the surface has a big absorption then good sprinkling of the surface is needed. 4. It can be used as a plaster of different wall bricks as 2 nd hand. For the 2 nd hand to be done, at least one day has to pass from the enforcement of the 1 st hand. 5. A 25 L bag covers approximately 1 m 2 of plastering with thickness 20-25mm always under normal conditions. 6. The surface can be covered with all Paralimnitiko plasters and ALFAKOL adhesives. For the final coat is recommended to use THERMO ΤΡΙΤΟ ΧΕPI. Warning:We avoid the application of Thermosovas at high sun shines, temperatures and also hot wind. As result, is to avoid bad adhesion and cracks during the period of dryness and maturation of the surface. The plastered surface has to stay so it absorbs for at least 7 days in 119

134 summer, and 14 days in winter, so the cracks can be covered with the next plaster (3 rd hand plaster). Technical characteristics: Thermosovas: Product definition: Type: Powder Granulometry: mm Colour: Grey Specific Gravity: 0.55 kg/lt Composition of dry materials: 100% Storage: 9 months in a dry place, closed sealed sack Package & Weight: Bags of 25Lt Toxicity / Inflammability: No Elements of use : Composition of mixture: Thick Water requirements: 6-8 L Water / 25 L dry product (1 bag) Mixture weight: 0.6 kg/lt Application temperature: +5 ºC ºC ΡΗ mixture: >10 Self life in bucket: Approximately 1hour Application width: mm Consumption: 25 L/m² for application width mm, depending on use and surface Waiting time for finishing coating: 7 days for summer season and 14 days for winter season Strengths: Adhesion strength (28 days): Flexural strength (after 28 days) Compressive strength (after 28 days) Thermal conductivity λ 10, dry 0.1 N/mm² - FP:A 1.2 N/mm² 1.1 N/mm² - CSI T1- λ 0.1 W/m K Note: The directives that are given above for our products are based on extensive research and experiments that were done by accredited European laboratories. We guarantee the constant and high quality of our products. Also, the information that is provided in this document, constitute the opinion of Producer Company, that however can be effected from others. The users of the product have the responsibility to follow correct processes of hygiene and safety. We do not have any responsibility for any damage or loss by factors that are not controlled by our company. For any other information contact with AVRAAM PITTAKIS and SONS LTD. 120

135 Declaration of Performance: No.: AP122 CPR - 01/07/ Unique identification code of the product-type: THERMOSOVAS Type, batch or serial number or any other element allowing identification of the construction product: The batch code of manufacture is printed on packaging. 3. Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer: Thermal Insulating Mortar (T) 4. Name, registered trade name or registered trade mark and contact address of the manufacturer as required under article 11 (5): AVRAAM PITTAKIS & SONS LTD P.O. box: 33006, 5310 Paralimni, Cyprus info@paralimnitiko.com 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in article 12 (2): Not applicable 6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V: System 4 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard: CYS ΕΝ 998-1: In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued: Not applicable. 9. Declared performance Essential characteristics Reaction to fire Adhesion Compressive Strength Class Α1 Performance 0.1 Ν/mm 2 - FΡ: A CSI Water Absorption W1 Water Vapour permeability coefficient μ 6 Dry Bulk Density 550 kg/m 3 Harmonised Technical Specification ΕΝ 998-1: 2010 Thermal Conductivity, λ 10, dry Durability (against freeze/thaw) Class Τ1 - λ 0.1 W/m K Evaluation based on provisions valid in the intended place of use of the mortar. 10. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. Signed for and on behalf of the manufacturer by: Κoutsofta Κaterina, Chemical Engineer Paralimni, 01/07/

136 122