Screeds with Underfloor Heating

Transcription

1 Screeds with Underfloor Heating Guidance for a defect-free interface Edited by Roderic Bunn and Dick Roberts Interface Engineering Publications is a Co-Construct initiative supported by

2 What is Co-Construct? Co-Construct is a network of five leading construction research and information organisations - Concrete Society, BSRIA, CIRIA, TRADA and SCI - who are working together to produce a single point of communication for construction professionals. BSRIA covers all aspects of mechanical and electrical services in buildings, including heating, air conditioning, and ventilation. Its services to industry include information, collaborative research, consultancy, testing and certification. It also has a worldwide market research and intelligence group, and offers hire calibration and sale of instruments to the industry. The Construction Industry Research and Information Association (CIRIA ) works with the construction industry to develop and implement best practice, leading to better performance. CIRIA's independence and wide membership base makes it uniquely placed to bring together all parties with an interest in improving performance. The Concrete Society is renowned for providing impartial information and technical reports on concrete specification and best practice. The Society operates an independent advisory service and offers networking through its regions and clubs. The Steel Construction Institute (SCI) is an independent, international, memberbased organisation with a mission to develop and promote the effective use of steel in construction. SCI specialises in providing advanced internet-based solutions for the construction industry. TRADA provides timber information, research and consultancy for the construction industry. The fully confidential range of expert services extends from strategic planning and market analysis through to product development, technical advice, training and publications. For more information on Co-Construct visit Screeds with Underfloor Heating Copyright of all material is this publication rests with the Concrete Society and BSRIA. Guidance appearing in the green text boxes is copyright Concrete Society Ltd, while all guidance in blue text boxes is copyright BSRIA. All photographs and illustrations in this publication were provided by BSRIA and The Concrete Society. Authors: Dick Roberts is with The Concrete Society, and Roderic Bunn is with BSRIA. Cover Illustration: Jason Harris. This publication was part-funded by the Department of Trade and Industry under the Partners In Innovation (PII) collaborative research programme. The views expressed in this publication are not necessaily those of the DTI. Final editorial control and publishing responsibility of this publication rested with BSRIA. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means electronic or mechanical including photocopying, recording or otherwise without prior written permission of the publisher. BSRIA/The Concrete Society IEP11/2003 August 2003 ISBN Printed by The Chameleon Press Ltd

3 In this guide Introduction Underfloor heating is an established technology. However, while the design and operating principles are well known to building services engineers, the finer points of design and installation may not be known by other specialists such as structural engineers, concrete contractors, installers and facilities managers. Disputes commonly occur on-site where particular items of work were assumed to have been carried out by another party, and as a consequence the work was not completed. With water-based underfloor heating, a common interface problem is between the heating element installation and the screed. If these interface problems are not understood, failures in system performance and/or failure of the screed may occur. This publication, the first in a series of similar guidance notes called Interface Engineering Publications, has been compiled by BSRIA and The Concrete Society. The objective of this publication is to provide building services engineers and screed specialists with consistent, interlocking advice on how water-based underfloor heating systems and screeds fit together technically, and in relation to the work programme. This guide largely contains material repackaged from existing BSRIA and Concrete Society guidance. Where possible this has been done word-for-word to avoid giving conflicting or ambiguous guidance. Details of the original publications, relevant European and British standards and other references for further reading are provided at the end of this publication. All reputable underfloor heating suppliers will provide detailed guidance on the application of their products, and the correct ways to interface those products with screeds and floor coverings. This interface publication should therefore be considered as providing the minimum requirements, with the detailed requirements for the installation being provided by the underfloor heating supplier. Finally, the design of a floor should be considered a top-down activity, not a bottom-up activity. The choice of floor type will affect the position of joints in the screed and therefore the positioning of the pipework. Flooring type is therefore very much a client briefing issue - not just for reasons of aesthetics, but also for reasons of system performance. SCREEDS WITH UNDERFLOOR HEATING 1

4 How to use this guide Advice about the mechanical engineering requirements of underfloor heating systems will be found in blue-tinted boxes. Comments marked by link to screeding sections listed under also see. Comments marked by denote a link common to both specialisms. Advice about the screeding requirements of underfloor heating systems will be found in green-tinted boxes. Comments marked by link to mechanical engineering sections listed under also see. Comments marked by denote a link common to both specialisms. Key mechanical watchpoints Essential mechanical engineering messages from the guide Key screeding watchpoints Essential screeding messages from the guide Also see Links to m&e sections Links to screeding sections Links to common sections Standards for screeds and m&e design Further reading to support this guide Glossary for terms and definitions 2 SCREEDS WITH UNDERFLOOR HEATING

5 Contents Introduction 1 Client briefing 4 Client briefing advice: services Client briefing advice: screeds Outline design 6 Services design information needed Warranty and guarantees Screed information needed Detailed design: services 8 Mechanical information needed Design outputs Design checks Design information for contractors Insulation details Detailed design: screeds 10 Screeds design information needed Design outputs Screed materials Sand/cement screeds Calcium sulfate and anhydrite screeds Pumpable screeds Drying the screed Floor construction Finishes Screeds: services design issues Pre-installation issues Installation 16 Services installation issues Pipework fixing Screed installation issues Pressure testing and drying Commissioning 18 Services commissioning issues Screed finishing issues Cost model 20 Standards and further reading 21 Glossary 22 SCREEDS WITH UNDERFLOOR HEATING 3