Effective Date: December Rev. 3/22/2018- Void After: December Product: Flush Valves File No. 3949

Transcription

1 IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a combination of both to verify compliance to the requirements of applicable codes and standards. This activity is coupled with periodic surveillance of the supplier's factory and warehouses as well as the assessment of the supplier's Quality Assurance System. This listing is subject to the conditions set forth in the characteristics below and is not to be construed as any recommendation, assurance or guarantee by IAPMO Research and Testing, Inc. of the product acceptance by Authorities Having Jurisdiction. The most updated information on this Certificate of Listing is available online at pld.iapmo.org Effective Date: December Rev. 3/22/2018- Void After: December 2018 Dba: Wdi Plbg. Inc. & Wdi Intl 3 Musick Irvine, CA Identification: Flush valves shall be marked with the manufacturer name or registered trademark or in case of private labeling of the customer for whom the unit was manufactured. This mark shall be readily identified and permanently affixed. The product shall also bear the cupc certification mark. Characteristics: Flush valves complete with optional rubber, vinyl or plastic flapper with stainless steel chain or dacron cord with acetal beads, overflow tube, nut and washer. To be installed with an IAPMO listed anti-siphon ballcock, and in accordance with the requirements of the latest edition of the Uniform Plumbing Code. To be installed in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code. Products listed on this certificate have been tested by an IAPMO R&T recognized laboratory. This recognition has been granted based upon the laboratory's compliance to the applicable requirements of ISO/IEC This listing period is based upon the last date of the month indicated on the Effective Date and Void After Date shown above. Any change in material, manufacturing process, marking or design without having first obtained the approval of the Product Certification Committee, or any evidence of non-compliance with applicable codes and standards or of inferior workmanship, may be deemed sufficient cause for revocation of this listing. Production of or reference to this form for advertising purposes may be made only by specific written permission of IAPMO Research and Testing, Inc. Any alteration of this certificate could be grounds for revocation of the listing. This document shall be reproduced in its entirety.

2 Products are in compliance with the following code(s): Uniform Plumbing Code (UPC ) National Plumbing Code of Canada International Plumbing Code (IPC ) Products are in compliance with the following standard(s): ASME A /CSA B including Update No. 1 dated May 2012 and CSA B

3 MODELS: B1016 B1017 B4006-G B4006-R B4100 B4210(X-X) W4310HDM Plastic Flush Valve for Gravity Feed Water Closets Flush Valve has an Elevated Seat Plastic water Closet flush valve w/overflow tube Plastic Flush valve for standard two-piece water closet Plastic Flush valve for standard one-piece water closet Plastic water Closet flush valve w/overflow tube and adjustable flapper Plastic Plastic Flush valve for special one-piece water closet Notes: 1 st X: A = Pedestal base, side lever B = Pedestal base, top-mounted push button C = Standard base, side lever D = Standard base, top-mounted push button 2 nd X: G = For 2-piece toilets R = For 1-piece toilets B4117 B " B4800X B4048 Plastic flush valve for gravity feed water closet w/3-1/4" riser Plastic flush valve for gravity feed water closet w/2-1/2" riser Plastic 3 inch flush valve Plastic flush valve for gravity feed one-piece water closets Note: "X" represents one of the letters "R", "D", or "H" as a manufacturer's designation for one-piece gravity feed Water Closet Tanks, and "X" can also represent one of the letters "G", "C", or "J" as a manufacturer's designation for two-piece gravity feed Water Closet Tanks. B4260S(X)-Y S=single Note: X = T, MT, HT or nothing Y = G, R, U B4220FLL-Y Y = G, U Page 3 of 5

4 B4261S(X)-Y S=single Note: X = T, MT or nothing Y = G, R, U B4262HMH-Y Y = G, R B4803-X 3 flush valve X = G, R B4804-X X = G, R B4260FSL- X B4260HHH- X B4260HMH- X B4260HSH- X X= G,R,U B4920FLL-X 2 Flush valve X = G, U Page 4 of 5

5 ADDITIONAL COMPANY INFO: Gerber Plumbing Fixtures Corporation PN Plastic flush valve for gravity feed water closet w/2-1/2" riser Axent Corporation LTD B4310HDM Plastic Flush valve for special one-piece water closet Page 5 of 5