testo 350-S/-XL testo 350 S/XL, flexible flue gas measuring system Additional information at Control unit Analysis box

Transcription

1 testo 350 S/XL, flexible flue gas measuring system 4 user defined function buttons Data communication via PC Integrated printer Prints readings on site Particle filter Control unit Analysis box Integrated Peltier gas preparation unit Integrated differential pressure probe testo 350 is a flexible, portable analysis system which is basically made up of a control unit, a flue gas analyser and a flue gas probe, depending on customer requirements. The detachable control unit can control the analysis system and read out data. The testo 350 XL control unit can also be used as a separate handheld analyser for differential pressure (built-in) and also for temperature, humidity, flow etc. thanks to its additional probe socket. Readings are printed on the built-in printer. The flue gas analyser is the heart of the analysis system and is available in two different versions: testo 350 S Basic version testo 350 XL Advanced version. The testo 350 S flue gas analyser is equipped with a measuring module for O 2 as standard. One measuring module must be fitted or up to 5 additional measuring modules for NO (option), NO 2 (option), SO 2 (option), NO low (option), CO (Option), CO low (option), H 2 S (option), C x H y (Option) or CO 2 via infrared measuring module (option) can be fitted. Temperature and differential pressure as well as the usual parameters such as Δ, qa, etc. are also calculated. The even more convenient testo 350 XL flue gas analyser is equipped with measuring modules for O 2, CO, NO and NO 2 as standard. Additional measuring modules for C x H y (option), NO low (option), CO low (option), SO 2 (Option), H 2 S (option) or CO 2 via infrared measuring module (option) are available. In addition to the features of the S version, the testo 350 XL flue gas analyser also has a Peltier gas preparation unit with a hose pump to regulate condensate disposal as well as a fresh air valve for long-term measurements lasting several hours. Both versions of the flue gas analysers can be equipped with up to 6 measuring modules, have a built-in rechargeable battery as standard, (for battery operation), data logger (250,000 readings) as well as a Testo data bus connection. The testo 350 S flue gas analyser can be retrofitted with all the features/functions of the testo 350 XL flue gas analyser. Tests and permits TÜV Bayern RgG 211 Conforms to DIN EN Part 2 Testo data bus User defined probe socket Connection for flue gas probe + additional C temperature probe Tests and permits TÜV Bavaria RgG 211 Conforms to DIN EN Part 2 Robust housing with impact protection Integrated differential pressure/velocity measurement 20

2 testo 350 S/XL, flexible flue gas measuring system S Control unit displays measurement data and controls measurement system, built-in printer, connection for Testo data bus and terminal plug included testo 350 S control unit XL testo 350 XL control unit Control unit displays measurement data and controls the measurement system, incl. built-in printer, pressure measurement 40/200 hpa, 1 user defined probe socket, programmable measurements and memory space for 250,000 readings, connection for Testo data bus, incl. terminal plug testo 350 S flue gas S analysis box testo 350 S flue gas analyser, equipped with: O 2, differential pressure measurement, 2 temperature probe sockets, testo data bus connection, built-in rechargeable battery, data logger, can be upgraded to max. 6 measurement modules (with NO, NO 2, CO, H 2 S, HC, SO 2, CO 2 NDIR) A second measurement module must be installed in testo 350 S, otherwise the instrument is unable to function. Up to 5 additional measurement modules can be fitted testo 350 XL flue gas XL analysis box testo 350 XL analyser box, equipped with O 2, CO (with switch-off and rinse function), NO, NO 2, differential pressure measurement, 2 temperature probe sockets, gas preparation, Testo data bus adapter, automatic fresh air rinse with valve (including measurement range extension with dilution factor 5 for all sensors), built-in rechargeable battery, data memory, can be upgraded to max. 6 measurement modules (with H 2 S, HC, SO 2, CO 2 NDIR) Differences between control units at a glance Differences between flue gas analysers at a glance Built-in printer Differential pressure measurement (-40 to +40 hpa / -200 to +200 hpa) 1 user-defined probe socket (for e.g. temperature, relative humidity measurement, etc.) Touchscreen Connection from a flue gas analyser to the Testo data bus Connection of several flue gas analysers, analog output boxes and testo 454 loggers to the Testo data bus NiMH rechargeable battery pack Internal memory for 250,000 readings = Standard = option testo 350 S control unit = Not possible testo 350 XL control unit Maximum no. of measuring modules O 2 CO (H2) CO low (H2) NO NO low NO 2 SO 2 HC H 2 S 0 25 Vol. 0 10,000 ppm ppm 0 3,000 ppm (0.1 ppm resolution) ppm (0.1 ppm resolution) ppm (0.1 ppm resolution) 0 5,000 ppm 0 4 Vol. % (0.001 % resolution) ppm (0.1 ppm resolution) testo 350 S 6 testo 350 XL 6 CO 2 (NDIR) 0 50 Vol. % Built-in gas preparation unit (is recommended with high humidity levels in flue gas and during long-term measurements >2 hrs measuring time) Automatic fresh air rinse with valve (incl. measurement range extension with dilution factor 5 for all sensors) Measurement range extension for CO measuring module (with selectable dilution factors) CO measuring module switch-off via adjustable switch-off threshold Trigger input stops and starts measurement externally Differential pressure measurement (-40 to +40 hpa / -200 to +200 hpa) Built-in rechargeable battery 2 temperature probe sockets (Type K NiCr-Ni) Data logger (250,000 readings) Testo data bus connection = Standard = option 21

3 Versatile exhaust gas measurement system testo 350-S/-XL Control unit testo 350-XL Testo databus controller with USB connection Flue gas analyzer testo 350-S/-XL Testo databus Logger testo 454 m/s, t/y ΔhPa, mbar ma out Power box NO X, SO 2, O 2, CO 2,... m/s, m³/h ΔhPa, Pa C %RH The system concept testo 350-S/-XL For many applications in the industrial sector, an analyser with additional features is needed to fulfill the following requirements: Simultaneous gas and process analysis at different measurement points without a time-consuming measurement point changeover switch Option of connecting additional parameters such as C; %RH; ma/mv etc. Long-term measurements in order to be able to assess different system cycles Flexibility of system in order to be able to react to the different requirements of the different systems. The testo 350-S/- XL measurement system fulfills these requirements. Several analyser boxes, equipped differently or up 10 loggers are connected together via the Testo data bus, over distances up to max. 1000m. If several analyser boxes, for example, are connected to the Testo data bus, they can be controlled, read out or programmed via the following: One analyser box after the other via the Control Unit, for example, or via the PC and an RS 232 cable Alternatively: Several analyser boxes simultaneously via the PC and a PCMCIA insert card. Parameters Parameters which can be measured using testo 350-S/-XL: a) testo 350-S/-XL analyser box Flue gas parameters such as O 2, CO, NO x, SO 2, H 2 S, HC, CO 2 (IR) Differential pressure, e.g. for combustion chamber pressure measurement Flow measurement with Pitot tube The analyser boxes are positioned at the respective measurement point. They are operated either connected to each other via the Testo data bus or as a separate datalogger without being connected. Separate measurement programs are saved in the analyser box e.g. measurement cycles, fresh air phases etc. testo 350-S and testo-xl and also boxes equipped differently can be used. Likewise loggers and analog outputs (6 ducts, 4-20mA) can be connected in this way (only to Control Unit testo 350-XL). b) Logger box Temperature, e.g. of surfaces, liquids Humidity, e.g. in suction ducts or ambient air Pressure, e.g. with differential pressure and high pressure probes Flow and volume flow, e.g. with vanes, hot wire probes rpm etc. 22

4 Versatile exhaust gas measurement system testo 350-S/-XL Site Date, Time Readings testo 350 XL SN: /D Smith Ltd. Milltown Site: Furnace 5 15:01:01 08:20:15 Fuel: Natural gas 10.9 % CO % O ppm CO 320 ppm NO Control unit Smith Ltd. Milltown Site: Furnace 5 14:01:01 15:24:16 1: hpa 2: 65.3 C Zuluftgebltor SN: ppm NO2 30 ppm SO2 120 ppm H2S 1050 C Flue gas temp C Ambient temp m/s Velocity 1.2 % Flue gas loss % HC Batch 25/2 Status display CO 2 % CO ppm H2S ppm HC PStop Set date/time 10.9 S Change date 23.6 E View Instrument % ppm VT C Service Fuel oil Fuel Site name TEST / % ppm Zoom NO x Selected analysis box Page no n % AT C ESC SO 2 OK ppm Gas dp = 0 4 user defined function buttons Easy to follow menu guide and operation Industrial probe Standard flue gas probes Pitot tube Suitable flue gas and velocity probes as well as temperature probes are available for a wide range of applications. Flue gas probes up to 4 m long, 1800 C are available, heated or non-heated (to avoid condensate). Temperature probes are also available for surface, gas and liquid measurements. Velocity probe options include vane and hot wire/hot bulb probes which can be connected to the control unit testo 350-XL in addition to Pitot tubes. 23

5 Gas sampling probes Sampling probes have to endure extreme conditions when measuring flue gases for example: High temperatures Corrosive condensate Dust Mechanical loads. The selection of the right probe is critical for accurate and consistent measurements. Because the sampling locations are often different, it s beneficial to have a standard probe designed for a wide variety of applications. In addition to the standard sampling probes, Testo also offers probe systems for specific industrial applications. Standard sampling probes Industrial probes Options to fit every application Standard sampling probes The standard sampling probe is available in lengths of 335 mm and 700 mm and for different temperature ranges. The outer pipe with a sintered filter is used for dusty flue gases. The hose has a standard length of 2.2 m (5 m optional). Material: probe pipe T max +500 C: Stainless steel Material: probe pipe T max C: Stainless steel /700 mm long Ø 8 mm Tmax. +500/+1000 C Option: Outer pipe with filter for dusty flue gases Hose length: Standard 2.2 m / 5 m optional T max 800 C Pore size: 3 μm / Material of probe pipe: Stainless steel Ø 10 mm Standard probes, 335 mm long Standard probes, 700 mm long Basic flue gas probe, 335 mm immersion depth incl. probe stop, NiCr-Ni (TI) T/C Tmax 500 C, probe shaft: stainless steel , 2.2 m hose, robust plug-in coupling Options Outer shaft with filter, Tmax C, 335 mm long, for dusty flue gases, 3 μm pore size, probe shaft stainless steel or Heat-resistant probe shaft (material: stainless steel ) with heat-resistant plate, 335 mm long, Tmax C Basic flue gas probe, 700 mm immersion depth incl. probe stop, NiCr-Ni (TI) T/C Tmax 500 C, probe shaft: stainless steel , 2.2 m hose, robust plug-in coupling Options Outer shaft with filter, Tmax C, 700mm long, for dusty flue gases, 3 μm pore size, probe shaft: stainless steel or Heat-resistant probe shaft (material: stainless steel ) with heat-resistant plate, 700 mm long, Tmax C ) Special hose for NO2/SO2 measurements, 2.2 m long Hose, 5 m long ) Special hose for NO2/SO2 measurements, 5 m long ) Special hose for NO2/SO2 measurements, 2.2 m long Hose, 5 m long (not for SO2 measurements) ) Special hose for NO2/SO2 measurements, 5 m long ) Use outer pipe with filter for dusty flue gases. 1) Use outer pipe with filter for dusty flue gases. Accessories Spare sintered filter (2 off) TÜV-tested gas sampling probes (specially for trade) TÜV approved flue gas probe, 180 mm immersion depth, up to +500 C, corr. to the latest instr. test guidelines, also for meas. on atmospheric gas systems, 2.2 m hose 180 mm Ø 8.0 mm TÜV approved flue gas probe, 335 mm immersion depth, up to +500 C, corresponding to the latest instrument test guidelines, also for atmospheric gas systems, 2.2 m hose 335 mm Ø 8.0 mm Attachable multi-hole probe for compact flue gas probes 180 mm and 335 mm, for CO mean value calculation in gas furnaces mm Ø 8.0 mm Length probe pipe 60 to 335 mm easy exchange with existing probe pipe

6 Industrial probes Options to fit every application Robust sampling probes for industrial applications This is a modular, portable probe system. The basic part of the system is the heated handle or non-heated adapter to which the sampling hoses are attached. A thermocouple, connected to testo 350 M/XL, is used for simultaneous temperature measurements. Using extension pipes (up to max. 3 m) the probe can be used in large flue gas ducts. A preliminary filter is screwed on to protect the probe if used in dusty gases. The heated probe (Ex. 1) is used for moist flue gases to eliminate false readings caused by the absorption of NO2 and SO2. The probes are attached to the flue gas duct using the mounting flange. Non-heated probe pipes are used for flue gases up to 1200 C (Ex. 2). The non-heated adapter can be used instead of a heated handle to measure O2, CO and NO or dry flue gases. Ceramic sampling pipes (Ex. 3) which can withstand the enormous thermal load are used for measurements at more than 1200 C. Example 1, Up to 600 C Thermocouple Heated handle Example 2, Up to 1200 C Mounting flange Heated sampling pipe Gas sampling hose Heated handle or non-heated adapter Sampling probe Extension pipes Extension pipe Ceramic preliminary filter Ceramic preliminary filter (max C) Example 3, Up to 1800 C Heated handle or non-heated adapter Ceramic sampling pipe Industrial probes Heated handle, power supply 115 to 230 V, 50/60 Hz Adapter, non-heated Non-heated sampling pipe to +600 C, stainless steel Non-heated sampling pipe to C, Inconel 625 Non-heated sampling pipe to C, Al-Oxide Heated sampling pipe, power supply 230 V / 50 Hz, stainless steel Heated sampling pipe, power supply 115 V / 60 Hz, stainless steel Extension pipe to +600 C, stainless steel Extension pipe to C, Inconel 625 Preliminary filter for dusty flue gases, ceramic Preliminary filter can only be mounted on extension pipe or Mounting flange, stainless steel , adjustable quick-action fitting suitable for all sampling/extension pipes Heated handle : Power: 115 to 230 V supply: 50/60 Hz Power required: 200 watts Temp. gas path: > 180 C Ready to operate: After approx. 20 min Mains cable: 3 m long Protection class: IP54 Ambient temp.: -20 to +50 C Gas input: G1/4 Gas output: M 10x1 outer thread 1.7 kg Adapter, non-heated : Ambient temp.: -20 to +50 C Protection class: IP54 Gas input: G1/4 Gas output:: M 10x1 outer thread 0.4 kg Non-heated sampling pipes Dimensions: Length: 1 m, Ø 12 mm Connection: G1/4 0.4 kg Sampling pipe up to +600 C : Material: Stainless steel Sampling pipe up to C : Material: Inconel 625 Sampling pipe up to C : Material: Al-Oxyd Heated sampling pipe : (230 V) (115 V) Dim.: Length: 1 m, Ø 25 mm Material: Stainless steel Heating: > +180 C Power 230 V / 50 Hz supply: 115 V / 60 Hz Power required: Connection: Max. flue gas temperature: +600 C 650 watts Electr. connection to heated handle Connection adapter with thread screw/ screw socket G1/4 Extension pipe Dimensions: L = 1 m, Ø 12 mm (pipe) Connection: Screw socket/ thread screw G1/ kg Extension pipe Up to +600 C Power consumption: 200 watts; Temp. gas path: > 180 C; Ready to operate: after approx. 20 min; Length of mains cable: 3 m; Protection class: IP54; Ambient temp.: -20 to +50 C; gas inlet: G1/4 ; gas outlet: M 10x1 outer thread; weight: 1.7 kg Ambient temp.: -20 to +50 C; Protection class: IP54; Gas inlet: G1/4?; Gas outlet: M 10x1 outer thread; 0.4 kg Connection: G1/4 ; 0.4 kg Ø 20 mm Ø 12 mm Connection: G1/4 ; 0.4 kg Ø 12 mm Ø 20 mm Ø 20 mm 130 mm : Material: Stainless steel Extension pipe Up to C.: Material: Inconel 625 Preliminary filter for dusty flue gases : Dust load: max. 20 g / m3 Filter fineness: 20 μm Temperature: max C Dimensions: 50 mm, Ø 20 mm Material: Ceramic Connection: G1/4 threaded nipple 0.2 kg Thermocouple : (1.2 m long) (2.2 m long) (3.2 m long) NiCr-Ni Sensor: : -200 to C Lengths: 1.2 / 2.2 / 3.2 m Diameter: 4 mm Material: Inconel 625 Connection: to analyser via 4 m connection cable with 8 pin plug kg Connection: Thread screw/screw socket G1/4 ; 0.45 kg Dust load: max. 20 g / m3; filter fineness: 20 μm; Temperature: max C; Material: ceramic; Connection: G1/4 thread nipple; 0.2 kg Standard sampling hose for connection to testo 350 M/XL analyser : Version: 1 Viton hose with robust plug Hose material: Viton Length: 4,0 m 0.4 kg Mounting flange.: Material: Stainless steel Diameter: Connection: Transport case for industry probes Transport case for industrial probes, aluminium, space for: handle, probes, flange and accessories Ø 12 mm 50 mm Ø 6.30 mm Ø 25 mm Heating: > +180 C; power consumption: 650 watts; Connection: electr. connection to heated handle, connection adapter with thread connection/screw socket G1/4 ; Max. flue gas temp.: +600 C Ø 20 mm Thermocouple, NiCr-Ni, -200 to C, Inconel 625, 1.2 m long Connection: To analyser via 4 m connection cable with pin plug; 0.15 kg. Thermocouple, NiCr-Ni, -200 to C, Inconel 625, 2.2 m long Ø 4 mm The length depends on the number of sampling and Thermocouple, NiCr-Ni, -200 to C, Inconel 625, 3.2 m long extension pipes used Gas sampling hose, 4 m, standard version 4 m 0.4 kg Special sampling hose for accurate NO2/SO2 measurements, 4 m long Hose material inside: PFFE hose with 2 mm inner diameter (lowest 4 m absorption, self-cleaning effect); Material outside: rubber; length: m; 0.45 kg mm Movable quick-action fitting, suitable for all sampling and extension pipes Special sampling hose for accurate N02/S02 measurements for connection to testo 350 M/XL analyser : Version: patented 1 way hose with robust plug Host material/inner: PTFE hose with 2 mm inner diameter (lowest absorption, self-cleaning effect) Host material/outer: Rubber Length: 4 m 0.45 kg

7 More probes Temperature Illustration t 99 Ambient air probe, 300 mm immersion depth, with 0 to +100 C 30 s probe stop for separate measurement of ambient 300 mm air temperature (e.g. systems with outside primary Ø 5 mm air intakes) Ambient air probe, immersion depth 190 mm, with probe stop, magnetic clip, Tmax C, for ambient air temperature measurement in systems dependent on/independent of ambient air Mini ambient air probe, 60 mm immersion depth, w. probe stop, magnetic clip, Tmax +100 C, for dual wall clearance temp. meas. in systems w. outside primary air intakes 190 mm Ø 4.0 mm 60 mm Ø 4 mm 0 to +100 C 0 to +100 C 30 s Mini ambient air probe, Tmax +80 C, for separate ambient air temperature measurement 0 to +80 C Pipe wrap probe for pipes with diameter of up to 2", for flow/return temp. meas. in hydronic -60 to +130 C Class 2 5 s systems Conn.: Fixed cable Spare meas. head for pipe wrap probe, TC Type K 35 mm -60 to +130 C Class 2 5 s Fast-action surface probe with sprung thermocouple strip, for measurements on floor heating, radiators, insulations mm 150 mm Ø 10 mm Conn.: Plug-in head. connection cable or required -200 to +300 C Class 2 3 s More probes Illustration Other features t 90 Gas leak detection probe to detect leaks in gas 200 mm 0 to ppm CH 1st alarm limit: 200 ppm CH4 4 2 s nd alarm limit: 10,000 ppm CH4 heating systems Ambient CO probe, for detecting CO in buildings and rooms Ø 20 mm Alarm: optical display (LED) and audible signal (buzzer) triggered if alarm limit is exceeded Fixed cable 1.5 m 0 to +500 ppm CO ±5% of mv ( to +500 ppm CO) ±5 ppm CO (0 to +100 ppm CO) Ambient CO2 probe 0 to +1 Vol. % CO 2 ±(50 ppm CO 2 ±2% of mv)(0 to to ppm CO ppm CO 2 ) 2 ±(100 ppm CO 2 ±3% of mv)(+5001 to Conn.: Plug-in head. connection cable or required ppm CO 2 ) Current/voltage cable (±1 V, ±10 V, 20 ma) 0 to mv ±1 mv (0 to mv) to +10 V ±0.01 V (0 to +10 V) 0 to +20 ma ±0.04 ma (0 to +20 ma) Mechanical rpm probe with plug-in head 20 to rpm Plug-in head. connection cable or required Included 2 probe tips Ø 8 and Ø 12 mm Conn.: Plug-in head. connection cable or required 1 hollow cone Ø 8 mm 1 surface speed disc Ø 19 mm to measure rotational speed: rpm = rotational speed in mm/s Stationary probes Illustration t 99 Robust, quick-action surface probe, NiCr-Ni, with -50 to +180 C Class 2 3 s M14 x 1.5 thread, incl. 2 nuts for mounting, 2 m cable (silicone) Universal probe, NiCr-Ni, for measurements in 500 mm -200 to C Class 1 2 s Inconel liquids and gases, 2 m cable (PVC), IP 42 Ø 1.5 mm connection socket Immersion probe, Pt100, for measurements in water and unclean environments, 2 m cable (silicone) 100 mm Ø 6 mm to +180 C Class A 70 s Immersion probe, Pt100, for measurements in corrosive substances, 2 m cable (PTFE), IP mm Ø 5 mm PFA -50 to +260 C Class A 50 s Resistance thermometer, Pt100, for surface measurement, 2 m cable (silicone), IP mm Al 8x8 mm -30 to +180 C Class A 150 s Universal probe, Pt100, for measurements in liquids and gases, 2m cable (PVC), IP mm Ø 3 mm to +400 C Class A 15 s Vane probe, Ø 16 mm, for stationary assembly, 3 m cable (PVC) 250 mm Ø 16 mm +0.4 to +60 m/s ±(0.2 m/s ±1% of mv) (+0.4 to +60 m/s) Robust hot bulb probe, Ø 3 mm, for measurements in the lower velocity range, 2m cable (PVC) 150 mm Ø 3 mm Ø 3 mm 0 to +10 m/s -20 to +70 C ±(0.03 m/s ±5% of mv) (0 to +10 m/s) Stationary probes Accessories Stationary probes Accessories Wall holder with screw-in connection for vane probe, Ø 16mm Clamp screw connection (steel) with G 1/4" thread, to attach temperature probes with Ø 6mm Clamp screw connection (steel) with M 8x1 thread, to attach temperature probes with Ø 3mm 26

8 More probes Humidity probes Illustration t 90 Standard ambient air probe up to +70 C, Plug-in head, 0 to +100 %RH ±2 %RH (+2 to +98 ±0.4 C (-10 to +50 C) 12 s connection cable or required -20 to +70 C %RH) ±0.5 C (remaining range) Ø 12 mm Robust humidity probe e.g. for measuring equilibrium moisture or for measurements in exhaust ducts to +120 C, Plug-in head, connection cable or required Robust high temperature/humidity probe up to +180 C, Plug-in head, connection cable or required 300 mm Ø 12 mm 300 mm Ø 12 mm 0 to +100 %RH -20 to +120 C 0 to +100 %RH -20 to +180 C ±2 %RH (+2 to +98 %RH) ±2 %RH (+2 to +98 %RH) ±0.4 C (-10 to +50 C) ±0.5 C (remaining range) ±0.4 C (+0.1 to +50 C) ±0.5 C (remaining range) 30 s 30 s Flow and pressure probes Vane/temperature probe, Ø 16 mm, attachable to handle or telescopic handle Illustration 180 mm Ø 16 mm +0.4 to +60 m/s -30 to +140 C ±(0.2 m/s +1% of mv) (+0.4 to +40 m/s) ±(0.2 m/s +2% of mv) (+40.1 to +50 m/s) Vane/temperature probe, Ø 25 mm, can be attached to handle or telescopic handle 180 mm +0.4 to +40 m/s -30 to +140 C ±(0.2 m/s ±1% of mv) (+0.4 to +40 m/s) High temperature vane probe, Ø 25 mm, with handle for continuous measurements up to +350 C 560 mm Ø 25 mm Ø 25 mm +0.6 to +20 m/s -40 to +350 C ±(0.3 m/s ±1% of fsv) (+0.6 to +20 m/s) Precision pressure probe, 100 Pa, in robust metal housing with impact protection, incl. magnet for fast attachment, to measure differential pressure and flow speeds (in combination with Pitot tube) Pressure probe, 10 hpa, in robust metal housing with impact protection incl. magnet for fast attachment, to measure differential pressure and flow speeds (in combination with Pitot tube) Pressure probe, 100 hpa, in robust metal housing with impact protection, incl. magnet for fast attachment, to measure differential pressure and flow speeds (in combination with Pitot tube) Plug-in head. connection cable or required Plug-in head. connection cable or required Plug-in head. connection cable or required 0 to +100 Pa 0 to +10 hpa 0 to +100 hpa ±(0.3 Pa ±0.5% of mv) ±0.03 hpa ±0.5% of mv (+20 to +100 hpa) ±0.1 hpa (0 to +20 hpa) Pitot tubes for flow measurement Pitot tube, 350 mm long, stainless steel, for measuring flow velocity in connection with / pressure probes Illustration 350 mm Ø 7 mm Oper. temp. 0 to +600 C Pitot tube, long, stainless steel, measures flow speed with pressure probes / Ø 7 mm Oper. temp. 0 to +600 C Pitot tube, stainless steel, 500 mm long, measures flow speed with temperature, for pressure probes / mm Ø 8 mm -40 to +600 C Pitot tube, stainless steel, 750 mm long, measures flow speed with temperature, 3x hoses (5 m long) and heat protection plate 750 mm Ø 8 mm -40 to C Pitot tube, stainless steel,, measures flow speed with temperature, for pressure probes / to +600 C Ø 8 mm Zubehör Accessories Zubehör Accessories Professional telescopic handle for plug-in vane probes, max. 1 m long, Cable, 1.5 m long, connects probe with plug-in head to meas. instrument, extension on request PUR coating material Extension for telescopic handle, 2 m long, please also order the extension cable Handle for plug-in vane probes Hose connection set for gas pressure measurement in heating systems, incl. silicone hoses and T-pieces, For separate gas pressure measurement ISO calibration certificate/pressure, differential pressure, accuracy 0.1 to 0.6 (% of fsv) ISO calibration certificate velocity, hot wire, vane anemometer, Pitot tube; calibration points 1; 2; 5; 10 m/s ISO calibration certificate velocity, hot wire, vane anemometer; calibration points 0.5; 0.8; 1; 1.5 m/s ISO calibration certificate velocity, hot wire, vane anemometer, Pitot tube; calibration points 5; 10; 15; 20 m/s Cable, 5 m long, connects probe with plug-in head to measuring instrument, PUR coating material Extension cable, 5 m long, between plug-in head cable and instrument, PUR coating material Telescopic handle, max. 1 m, for probe with plug-in head, cable: 2.5 m long, PUR coating material Control and humidity adjustment set 11.3%RH/75.3%RH incl. adapter for humidity probes, quick checks or calibration of humidity probe Telescopic handle, mm long ISO calibration certificate/temperature, meas. instr. with surface probe; calibration points +60 C; +120 C; +180 C ISO calibration certificate humidity, electronic hygrometers; calibration points 11.3 %RH and 75.3 %RH at +25 C ISO calibration certificate/co2, CO2 probes; calibration points 0; 1000; 5000 ppm

9 Measurement System and Practical Accessories Zubehör testo 350 S control unit Zubehör Transport case and accessories for analyser boxes Control unit displays measurement data and controls measurement system, Wall holder for analyser box incl. heat protection plate, can be locked built-in printer, connection for Testo data bus and terminal plug included Zubehör testo 350 XL control unit Control unit displays measurement data and controls the measurement system, incl. built-in printer, pressure measurement 40/200 hpa, 1 user defined probe socket, programmable measurements and memory space for 250,000 readings, connection for Testo data bus, incl. terminal plug Protective cover for analyser box (can also be used with wall holder) Carrying belt set for analyser box and control unit Transport case for analyser, probes and accessories Additional options only for control unit testo 350 XL Touch screen with pen (available only with original order), for easy input of text and values Zubehör testo 350 S flue gas analyser testo 350 S flue gas analyser, equipped with: O 2, differential pressure measurement, 2 temperature probe sockets, testo data bus connection, builtin rechargeable battery, data logger, can be upgraded to max. 6 measurement modules (with NO, NO 2, CO, H 2 S, HC, SO 2, CO 2 NDIR) A second measurement module must be installed in testo 350 S, otherwise the instrument is unable to function. Up to 5 additional measurement modules can be fitted. Option: COlow measurement module Option: CO measurement module Option: CO2 meas. module (infrared meas. principle, absolute pressure meas and CO2 absorption filter with refill pack incl.) Option: HC measurement module (nonburned hydrocarbons) Option: H2S measurement module Option: NO measurement module Option: NOlow measurement module Option: NO2 measurement module Option: SO2 measurement module Option: Peltier gas preparation with hose pump to empty condensate automatically Fresh air valve for long-term measurement (measurement range extension with dilution factor 5 for all sensors included) Measuring range extension for CO measurement module (dilution), built into analyser box, selectable dilution factors: 0, 2, 5, 10, 20, 40 Event trigger socket, for starting and stopping measurement externally, built into analyser box Zubehör testo 350 XL flue gas analyser box testo 350 XL analyser box, equipped with O 2, CO (with switch-off and rinse function), NO, NO 2, differential pressure measurement, 2 temperature probe sockets, gas preparation, Testo data bus adapter, automatic fresh air rinse with valve (including measurement range extension with dilution factor 5 for all sensors), built-in rechargeable battery, data memory, can be upgraded to max. 6 measurement modules (with H 2 S, HC, SO 2, CO 2 NDIR) Option: COlow measurement module Option: CO2 meas. module (infrared meas. principle, absolute pressure meas and CO2 absorption filter with refill pack incl.) Option: NOlow measurement module Option: SO2 measurement module Option: HC measurement module (nonburned hydrocarbons) Option: H2S measurement module Measuring range extension for CO measurement module (dilution), built into analyser box, selectable dilution factors: 0, 2, 5, 10, 20, 40 Event trigger socket, for starting and stopping measurement externally, built into analyser box Spare thermal paper for printer (6 rolls) Testo rechargeable battery pack NiMH for control unit, logger Power unit 230 V/ 8 V/ 1 A, for instrument (European plug) System case (aluminium), with drawer for accessories, for transport and protection during measurement Zubehör testo 454 logger and accessories Logger, measures and saves (max. 250,000 readings), incl. 4 user defined probe sockets, alarm output/event trigger socket, stand/wall holder Alarm/trigger cable Holding unit/theft-proof with lock for logger wall holder Power box, connected to control unit to increase operating life, for a batteryoperated measuring system Power unit for compact gas drier and flue gas analyser Analog output box, 6 channels, 4 to 20 ma, for output on an analog recorder, (please also order mains unit ) Testo rechargeable battery pack NiMH for control unit, logger Recharger for control unit or logger (with 4 standard rechargeable batteries), rechargeable batteries are recharged externally Zubehör Accessories for Testo data bus Mains unit (110/230 V; 50/60 Hz, 12 V, 3 A) supplies power to Testo data bus, when using the Testo plug-in card Terminal plug for Testo data bus, for loggers and special lengths Connection cable, 2 m, for Testo data bus Connection cable, 5 m, for Testo data bus Connection cable, 20 m, for Testo data bus Additional cable lengths up to 1000 m on request Zubehör PC software "easyemission" software for testo 350 S/XL, RS232 cable for connecting instrument to PC included "easyemission" software for testo 350 S/XL, Testo data bus controller included, with USB to connect instrument to PC, cable for Testo data bus and terminal plug Software upgrade of "easyemission" testo 350 S/XL to "easyemission" testo 335 Zubehör Accessories exhaust gas analysis instrument Cable to connect measuring instrument to pulse counter for gas flow measurement Additional box for system case , can be snapped on Transport case for industrial probes, aluminium; space for: handle, probes, flange and accessories Calculation of fuel-specific factors to accurately display calculated variables in deviating fuels (calculation for one fuel) Spare particle filter, pack of Hose set to convey flue gas from analyser box, 5 m long Refill pack of filter pellets for CO2 absorption filter ISO calibration certificate/flue gas, calibration points 2.5% O2; 100 and 1000 ppm CO; 800 ppm NO; 80 ppm NO2; 1000 ppm SO Electrical isolation for RS232 (connects measuring instrument to PC) Cable with adapter for cigarette lighter and adapter for connection to testo 350-S/-XL Cable with battery clamps and adapter for connection to testo 350-S/-XL

10 testo 350 M: Set for fast emission monitoring on industrial burners (O 2, CO, NO) - testo 350 S control unit ( ) - testo 350 S flue gas analysis box ( ) - Option: NO measurement module ( ) - Option: CO measurement module ( ) - Flue gas probe, 335 mm immersion depth, Thermocouple NiCr-Ni (TI), Hose 2.2 m ( ) - Heat-proof probe pipe, 335 mm long, Tmax C ( ) - Connection cable, 2 m, for Testo data bus ( ) - Protective cover for analyser box ( ) - Carrying belt set for analyser box ( ) - Transport case for analyser, probes and accessories ( ) - Spare particle filter, pack of 20 ( ) - Spare thermal paper for printer (6 rolls) ( ) testo 350 XL: Standard set for measurements on process systems (O 2, CO, NO, NO 2 ) - testo 350 XL control unit ( ) - Testo rechargeable pack for control unit ( ) - testo 350 XL flue gas analysis box ( ) - Flue gas probe, 335 mm immersion depth, Thermocouple NiCr-Ni (TI), Hose 2.2 m ( ) - Heat-proof probe pipe, 335 mm long, Tmax C ( ) - Special hose for NO2/SO2 measurements, 2.2 m long ( ) - Connection cable, 2 m, for Testo data bus ( ) - "easyemission" software for testo 350 S/XL ( ) - Protective cover for analyser box ( ) - Carrying belt set for analyser box ( ) - Transport case for analyser, probes and accessories ( ) - Spare particle filter, pack of 20 ( ) - Spare thermal paper for printer (6 rolls) ( ) testo 350 XL: Portable measurements on motors (O 2, CO, NO, NO 2 ) - testo 350 XL control unit ( ) - Testo rechargeable pack for control unit ( ) - testo 350 XL flue gas analysis box ( ) - Measurement range extension for CO measurement module (dilution) ( ) - Flue gas probe, 335 mm immersion depth, Thermocouple NiCr-Ni (TI), Hose 2.2 m ( ) - Heat-proof probe pipe, 335 mm long, Tmax C ( ) - Special hose for NO2/SO2 measurements, 2.2 m long ( ) - Connection cable, 5 m, for Testo data bus ( ) - "easyemission" software for testo 350 S/XL ( ) - Protective cover for analyser box ( ) - Carrying belt set for analyser box ( ) - System case (aluminium), incl. drawer ( ) - Spare particle filter, pack of 20 ( ) - Spare thermal paper for printer (6 rolls) ( ) testo 350 XL: Portable measurements on turbines (O 2, CO low, NO low, NO 2 ) - testo 350 XL control unit ( ) - Testo rechargeable pack for control unit ( ) - Touchscreen with reader ( ) - testo 350 XL flue gas analysis box ( ) - COlow measurement module, 0 to 500 ppm, built-in in the analyser box ( ) - NOlow measurement module, 0 to 300 ppm, built-in in analyser box ( ) - Measurement range extension for CO measurement module (dilution) ( ) - Flue gas probe, 335 mm immersion depth, Thermocouple NiCr-Ni (TI), Hose 2.2 m ( ) - Heat-proof probe pipe, 335 mm long, Tmax C ( ) - Special hose for NO2/SO2 measurements, 5 m long ( ) - Connection cable, 5 m, for Testo data bus ( ) - "easyemission" software for testo 350 S/XL ( ) - Protective cover for analyser box ( ) - Carrying belt set for analyser box ( ) - System case (aluminium), incl. drawer ( ) - Spare particle filter, pack of 20 ( ) - Spare thermal paper for printer (6 rolls) ( ) 29

11 Technical data Technical Data for Control unit testo 350-S/-XL and testo 454 logger box testo 350 S control unit testo 350 XL control unit Logger, measures and saves readings Analog output box (ma out) Oper. temp. -5 to +45 C -5 to +45 C -10 to +50 C -10 to +50 C Storage temp. -20 to +50 C -20 to +50 C -25 to +60 C -25 to +60 C Battery type 4 AA batteries 4 AA batteries Alkali manganese Battery life 8 h 8 h 24 h Memory readings readings Weight 850 g 850 g 450 g 305 g Dimensions 252 x 115 x 58 mm 252 x 115 x 58 mm 200 x 89 x 37 mm 200 x 89 x 37 mm Warranty 2 years 2 years 3 years 3 years Technical data control unit testo 350-XL and testo 454 logger box Probe type Vane Thermal ±1 digit Resolution 0 to +60 m/s See probe data for system accuracy 0.01 m/s (for Ø 60/100 mm), 0.1 m/s (for remaining probes) 0 to +20 m/s ±0.01 m/s (0 to m/s) ±0.02 m/s (+2 to m/s) ±0.04 m/s (+5 to +20 m/s) 0.01 m/s (0 to +20 m/s) Testo humid. sensor, cap. 0 to +100 %RH See probe data 0.1 %RH (0 to +100 %RH) Pressure +10 to hpa Probe Probe Probe Probe ±0.1% of m.v hpa (probe ) hpa (probe ) 0.01 hpa (probe ) Probe type Pt100 Type K (NiCr-Ni) Type S (Pt10Rh-Pt) Type J (Fe-CuNi) Type T (Cu-CuNi) -200 to +800 C -200 to C 0 to C -200 to C -40 to +350 C ±1 digit ±0.1 C (-49.9 to C) ±0.4 C (-99.9 to -50 C) ±0.4 C (+100 to C) ±1 C (-200 to -100 C) ±1 C (+200 to +800 C) ±0.4 C (-100 to +200 C) ±1 C (-200 to C) ±1 C ( to C) ±1 C (0 to C) ±0.4 C (-150 to +150 C) ±1 C (-200 to C) ±1 C ( to C) ±0.4 C (-40 to +200 C) ±1 C ( to +350 C) Resolution 0.01 C (-99.9 to +300 C) 0.1 C (-200 to -100 C) 0.1 C (+301 to +800 C) 0.1 C (-200 to C) 1 C (0 to C) 0.1 C (-200 to C) 0.1 C (-40 to +350 C) Probe type NTC CO probe CO2 probe CO2 probe -40 to +150 C 0 to +500 ppm CO 0 to +1 Vol. % CO 2 0 to ppm CO 2 ±1 digit ±0.2 C (-10 to +50 C) ±0.4 C (-40 to -11 C) ±0.4 C (+51 to +150 C) ±5% of mv (0 to +500 ppm CO) See probe data See probe data Resolution 0.1 C (-40 to +150 C) Probe type Mechanical Current/voltage measurement Current/voltage measurement Control unit, integ. press. sensor 20 to rpm 0 to +20 ma 0 to +10 V -200 to +200 hpa -40 to +40 hpa ±1 digit ±1 digit ±0.04 ma (0 to +20 ma) ±0.01 V (0 to +10 V) ±1.5% of mv (-50 to -200 hpa) ±1.5% of mv (+50 to +200 hpa) ±0.5 hpa (-49.9 to hpa) ±1.5% of mv (-3 to -40 hpa) ±1.5% of mv (+3 to +40 hpa) ±0.03 hpa (-2.99 to hpa) Resolution 1 rpm 0.01 ma (0 to +20 ma) 0.01 V (0 to +10 V) 0.1 hpa (-200 to +200 hpa) 0.01 hpa (-40 to +40 hpa) 30