British Museum--China dinosaur fossil exhibition transportation process.

Transcription

1 British Museum--China dinosaur fossil exhibition transportation process. Products: Chinese dinosaur fossils -- international first-class cultural relics. At the invitation of the British government, the exhibition of dinosaur fossils of China's special cultural relics was officially exhibited in June, 2017.The two parties have signed the first international cultural heritage contract about this exhibition. Chinese representative: the state council (Chinese Academy of Sciences and Ancient Spine Institute) British representative: the mayor of Nottingham and a team of British scientists. Media: major media and websites in China and the UK have been published. Chinese LOGISTICS carrier: YTD LOGISTICS (CHINA) British LOGISTICS carrier: CORTEN LOGISTICS (UK) The most important parts of the exhibition journey are transportation and packaging: shockproof packaging, inland transportation in China, international maritime transport and British domestic transportation. Step One About package: the packing of cargo dinosaur fossil model which is at 1:1 as real one and made of resin must be conducted by one or two persons, and usually takes about two to six months to complete. Package must be done step by step with great carefulness and the packaging must have a collision film and bubble pad to avoid shock. Step Two A. Seal the box after confirmation and affix the seal. B. The seal shall not be opened except for inspection by customs and consignor. C. The seal must be affixed at all directions (front and rear)

2 D. When sealing the box, must use high strength nails or high strength screws. Step Three A. As Beijing is the capital, it is necessary to bring all of relevant documents of all involved stuff to Beijing in case of local police asking. B. Due to long distance and goods need to proof rain, sand and long distance. So we finally confirmed that the flying wing car makes the best delivery vehicles. The flying wing car which can only be opened and closed when car is started on can ensure the security of cargoes. C. There are two places to pick up cargoes. The first place is Hohhot, Inner Mongolia province, and the second place is Changping district of Beijing. There is around 600km between these two places and it will take 8-10 hours by truck. D. Hohhot has two pieces of goods, and because the vehicle is too large, it is necessary to strengthen cargoes before it was sent to Beijing from Hohhot. Step Four, A. After arriving at the institute of vertebrate paleontology (Beijing) of the Chinese academy of sciences, the goods began to do the best loading planning and adjustment. B. Counting the number of wooden boxes of goods. C. Checking the packing details in each box. D. Reinforcing to prevent slipping when unpacking. E. Taking a picture or video of the process of cargoes loading.

3 Step Five, A. Lock the doors of both two sides of fly wing truck, then drive to next station---tianjin warehouse. B. From Beijing Changping district to Tianjin Binhai New Area wharf, there is about 300km and takes about five hours by truck. C. After arriving at warehouse, we started unpacking, taking photos and counting. D. Arrange the cargo into the container.

4 Step Six, A. When loading the container, we need to calculate weight and keep the balance of container to avoid one side is overweight than another side. B. The goods must be strengthened and fixed in the box, and the goods cannot be moved out of the original position in the container. C. The container loading process must be inspected by stuff from beginning to end. D. Because they are valuable goods, the forklift needs to be handled lightly. E. The reinforcing staff can only step on the side of the wooden box and step on the middle part of the wooden box is forbidden. F. Keep the packing and unloading completely consistent. G. Check that there are no visible cracks inside and outside the container, and the floors must be clean and tidy.

5 Step Seven, A. Check if the container is padlocked on a mobile trailer to prevent the container from sliding down the road. B. The door must be closed, and the four locks must be completely hung in the inner wall of the container. C. In order to ensure the safety of the goods, the seal must be sealed. D. The seal must be closed to the right of the container because the left door cannot be opened once the right door is blocked. E. Vehicle use must be equipped with a pneumatic shock absorber, so that the cargo will not be subjected to severe turbulence even in the potholes. Step Eight, A. Prepare documents like Chinese customs declaration. B. Common documents are: packing list, invoice, contract. C. The document must be used for the red head document of China's land management department. D. The ATA certificate is used for the exhibition of special products in China. E. All the documents must be submitted to the local customs office of China with the documents issued by the central customs administration. F. Issue the original telex release b/l to British company, and handle relevant local customs clearance procedures. Step Nine, A.The full transport policy is completed by the British government.

6 B.After arriving in the UK, the UK is responsible for all customs clearance and unpacking. C.The British company transported the goods to the exhibition site. D.After opening all the packages, start the inventory and installation work. E.There is no shortage of inventory, and the contract is complete according to the contract.at the same time, there are no flaws. F.No damage was found in the goods. G.No movement of the goods was found.

7 Step Ten, A. After 3 months of exhibition at the British museum, the packaging will begin in November B. Start loading containers at the end of November 2017, declare local customs, and prepare to ship back to China. C. The United Kingdom packages goods in the same way & reinforcement. D. The goods are shipped to China by sea. Step Eleven, A. The goods successfully completed the local customs clearance in tianjin and arrived at our company's XINGANG warehouse.

8 B. Take photos of the cargo information. C. Seal inspection is in good condition. D. container lock is in good condition. Step Twelve, A. The outside of the container is intact. B. There is a padlock between the box and the trailer. Step Thirteen, A. check lead seal B. open the seal

9 Step Fourteen, A. Open the container and check whether the packing case is broken. B. Remove the reinforcement and reinforcement. C. Bring the longer goods from the box at the slowest speed. D. After the goods are presented, all stationary piles shall be placed in the warehouse. E. After the container is unloaded, place all the cargo in the flying wing.

10 Step Fifteen, A. Cargo safety loading and reinforcement. B. Keep the goods balanced so that they don't sway on the highway. C. The goods are not visible on rainy days, windy sand and other weather. Flying wing is the best choice.you can better protect the goods from outside damage. D. Better prevention of stolen goods. E. The bottom of the vehicle must be equipped with a capsule air cushion to better relieve the turbulence during the transportation process.

11 Step Sixteen, A. cargo transport back to designated destination, first area: Chinese academy of sciences (Beijing) B. The guest is responsible for the on-site unloading. C. The guest is responsible for checking whether the outer packing is obviously damaged. Step Seventeen, A. cargo transport back to designated destination, first area: Chinese academy of sciences (Beijing) B. The goods are immediately checked and counted. C. No shortage or loss of goods.

12 D. The goods are in good condition. Step Eighteen, A. The goods are shipped back to the designated destination, the second area: Chinese academy of sciences (Hohhot, Inner Mongolia province) B. The goods are counted immediately. C. No shortage or loss of goods. D. The goods are in good condition.