Kerotest/Marsh Needle Valves Series N
|
|
|
- Diane Wheeler
- 6 years ago
- Views:
Transcription
1 Series N Kerotest/Marsh N Series Needle Valves are used in processing plants, oil and gas production, hydraulic and pneumatic equipment, testing labs anywhere the flow of fluid must be carefully regulated. All models are machined from quality bar stock for reliable performance. Connections range from 1/8 to 1 NPT in choice of globe or angle patterns. A panel mounting kit is available for the three hard seat models. These fine products are available from Kerotest Manufacturing Corp. Call or fax today for additional details. Panel Mounting Kit Each kit contains two stainless steel mounting nuts. Order by valve size from the part number table below. Value Size 1/8 1/4 3/8 1/2 3/4 1 Kit Number S S S3 Flow Rate Use the following equations to determine the flow rate of a fluid through a fully-open valve: LIQUID: P Q L = C V G Q L = Flow in GPM P = Differential pressure across the valve in psi G = Specific gravity of liquid ( for water, G = 1) GAS: Q g = 61C V P 2 P g Q g = Flow in CFH ( at STP ) P 2 = Outlet pressure ( psi ) g = Specific gravity of gas ( for air, g = 1 ) PATTERNS Series N Needle Valves are available in the following configurations. - Double female, globe pattern. - Male/female, globe pattern. FFA - Double female, angle pattern. - Male/female, angle pattern. Kerotest Manufacturing Corp Second Avenue Pittsburgh, PA Fax : Choice Of Six Valve Series For s Up To 10,000 PSI Connection Sizes From 1/8 To 1 NPT In Either Globe Or Angle Patterns Optional Panel Mount Adapter Kit Available For Selected Needle Valves Hard Seat And Soft Seat Designs Rugged Barstock Construction Field Proven For Over 50 Years
2 Hard Seat Needle Valves Alloy Steel An economical valve for regulating pressures up to 10,000 psi. Suitable for air, water, oil and other fluids with low-level corrosiveness. 20,000 PSI ( 140,000 kpa ) -20º to 800º F ( -28º to 426º C ) for Grafiflex* packed valves Body and Bonnet Material: AISI 1045 alloy steel Stem Material: 416 stainless steel, hardened Packing: Teflon, Grafiflex ( optional ) Handle: Two-prong. Cast aluminum for 1/8 through 1/2" sizes. Mallable iron for 3/4" and 1 sizes. Finish: Clear zinc plating. Assembly: Bonnet on all globe valves 1/2" and under is threaded into body and staked to prevent turning. Body and insert for angle valves fused into single unit by a welding process. * Registered trademark of DuPont. Zero clearance washers and nongalling Grafiflex packing ( optional ). Standard packing is Teflon. Outside threaded bonnet. One model serves either in-line or panel-mounting applications. Valve pictured with optional panel mount nuts installed Bonnet screwed into body and staked for added security Pattern NPT Size Part No. C V 1/8 N /4" N /8 N /2" N /4" N N /4" N /2" N /8 N /4" N FFA 3/8 N /2" N /4" N N /4" N /2" N Integral back-seated stem standard on globe patterns. Exclusive safety feature prevents accidental removal of stem Hard Seat Needle Valves 316 Stainless Steel Designed for applications where caustic liquids and corrosive media are common. 20,000 PSI ( 140,000 kpa ) -100º to 800º F ( -73º to 426º C ) for Grafiflex packed valves Body and Bonnet Material: 316 Stainless Steel Stem Material: 17-4 PH Stainless Steel Packing: Teflon, Grafiflex ( optional ) Handle: Two-prong. Stainless Steel for 1/8 through 1/2" sizes. Mallable iron for 3/4" and 1 sizes. Finish: Stainless steel is passivated ( surface contamination removed ). Assembly: Bonnet is threaded into body and staked to prevent turning. Stem Seal Packing Nut Zero clearance washers and nongalling Grafiflex packing ( optional ). Standard packing is Teflon. Outside threaded bonnet. One model serves either in-line or panel-mounting applications. Precision machined thread for perfect concentricity, easier operation Bonnet screwed into body and staked for added security Pattern NPT Size Part No. C V 1/8 N /4" N /8 N /2" N /4" N N /4" N /2" N /8 N /4" N FFA 3/8 N /2" N /4" N N /4" N /2" N Integral back-seated stem standard on globe patterns. Exclusive safety feature prevents accidental removal of stem
3 Hard Seat Needle Valves 316 Stainless Steel NACE Meets NACE standard MR for resistance to sulfide stress cracking. All 316 SST parts are RC 22 or less, meeting safety requirements in petroleum and gas production, pipeline, service, and offshore drilling where sour fluid environments can cause sulfide stress cracking. 20,000 PSI ( 140,000 kpa ) -100º to 800º F ( -73º to 426º C ) for Grafiflex* packed valves Body and Bonnet Material: 316 stainless steel, annealed to meet requirements of NACE standard MR Stem Material: 17-4PH stainless steel, heat treated to meet requirements of NACE standard MR Packing: Teflon, Grafiflex ( optional ) Handle: Two-prong. Stainless steel for 1/8 through 1/2" sizes. Malleable iron for 3/4" and 1 sizes. Finish: Stainless steel is passivated (surface contamination removed). Assembly: Bonnet is threaded into body and locked into place with a bonnet-locking pin. * Registered trademark of DuPont. Zero clearance washers and nongalling Grafiflex packing ( optional ). Standard packing is Teflon. Outside threaded bonnet. One model serves either in-line or panel-mounting applications. Precision machined 17-4PH SST stem for perfect concentricity and easier operation. Heat-treated to prevent sulfide stress cracking. Bonnet locking pin prevents accidental loosening of bonnet 316 SST annealed body and bonnet prevent sulfide stress cracking in sour fluid environments Pattern NPT Size Part No. C V 1/8 N1311N 0.4 1/4" N1312N 0.4 3/8 N1313N 0.9 1/2" N1314N 1.1 3/4" N1316N N1318N 3.5 1/4" N1332N 0.4 1/2" N1334N 1.2 1/8 N1351N 0.7 1/4" N1352N 0.8 FFA 3/8 N1353N 1.6 1/2" N1354N 1.5 3/4" N1356N N1358N 6.2 1/4" N1372N 0.6 1/2" N1374N 1.5 Packing Nut Integral back-seated stem standard on globe patterns. Exclusive safety feature prevents accidental removal of stem and eliminates possibility of stem blowout Soft Seat Needle Valves 316 Stainless Steel and Alloy Steel, Standard Port Recommended where bubble-tight seal and shutoff of liquids or gases are required. The design includes a replaceable Delrin* sleeve insert for added life value. 6,000 PSI ( 42,000 kpa ) 12,000 PSI ( 84,000 kpa ) -to 200º F ( 93º C ) Body and Bonnet Material: 316 stainless steel or AISI 1045 alloy steel Stem Material: 316 stainless steel with stainless body, 303 stainless steel with alloy steel body Bonnet Cap (Protective Cover): Polyethylene, red. Packing: Vitron* O-ring and Teflon backup ring (nylon backup ring for 1 size) Handle: Two-prong. Stainless Steel for 1/4 through 1/2" sizes. Malleable iron for 1 stainless steel. Cast aluminum for alloy 1/4" through 1/2" sizes. Malleable iron for alloy 1 size. Precision machined thread for perfect concentricity, easier operation Stem seal packing uses Vitron* O-ring and Teflon* backup ring Bonnet-pin lock prevents accidental removal of bonnet Replacement Delrin* sleeve insert extends valve life Straight-through flow decreases turbulence, improves flow characteristics Stainless steel roll-pin prevents misalignment of the sleeve *Vitron, Teflon, and Delfrin are registered trademarks of DuPont Finish: Stainless steel is passivated ( surface contamination removed ). Alloy steel has a zinc plated finish. Assembly: Bonnet-pin lock is standard for all softseat needle valves. Pattern Part Number NPT Size 316 SST Alloy C V 1/4" N5312 N /2" N5314 N N5318 N /4" N5332 N /2" N5334 N /4 x 1/2" N5335 N /4" N /2" N
4 Minature Needle Valves 316 Stainless Steel and Alloy Steel Ideal for limited space applications such as test stand circuitry, mobile equipment, etc. Body length less than 2. Maximum height with valve open is 2-1/2. 6,000 PSI ( 42,000 kpa ) 12,000 PSI ( 84,000 kpa ) -20º to 200º F ( 93º C ) Body and Bonnet Material: 316 stainless steel or AISI 1045 alloy steel Stem Material: 17-4PH stainless steel with stainless steel body, 416 stainless steel with alloy steel body Bonnet Cap (Protective Cover): Polyethylene, black Handle: Zinc plated steel, easy grip T-handle Finish: Stainless steel is passivated. Alloy steel has a clear zinc finish. Easy grip T-handle Precision machined stem for perfect concentricity and easier operation. Stem seal packing uses Viron* O-ring and Teflon* backup ring Bonnet threaded into body, secured with Loctite *Registered trademark of DuPont NPT Part No. Pattern Size 316 SST Alloy C V 1/8 N0311 N /4" N0312 N /4" N0332 N Block/Bleed Terminal Needle Valves 316 Stainless Steel and Alloy Steel These valves provide extra pressure outlets, permit line samplings, isolate gauges, provide a bypass, and eliminate extra connections and parts on a gauge leg, thereby reducing cost and increasing dependability. 30,000 PSI ( 140,000 kpa ) SST: -100º to 800º F ( -73º to 426º C ) Alloy: -20º to 800º F ( -28º to 426º C ) Grafiflex Packing Body and Bonnet Material: 316 stainless steel or AISI 1045 Stem Material: 416 stainless steel for alloy steel body, 17-4PH for 316 stainless steel body Packing: Teflon, Grafiflex (optional) Handle: Two-prong. Stainless steel for stainless steel. Cast aluminum for alloy. Side ports are 1/2" NPT. Finish: Clear Zinc plate for alloy steel. Stainless steel is passivated. Assembly: Bonnet is threaded into body and staked in place to prevent turning. Zero clearance washers and nongalling Grafiflex* packing (optional). Standard packing is Teflon*. Roll-formed stem threads for longer life Precision machined thread for perfect concentricity, easier operation Integral back-seated stem helps prevent accidental removal Hardened 416 stainless steel or 17-4PH SST needle, back-seated *Grafiflex and Teflon are registered trademarks of DuPont Carbon steel or 316 SST port plug Part Number Pattern NPT Size 316 SST Alloy C V Bleed 1/2" N8534 N Bleed 3/4 x 1/2" N8536 N
5 Soft Seat Needle Valves 316 Stainless Steel and Alloy Steel, Full Port Large bore size (0.257 ) permits cleanout with rod. The full-port, straight-through design reduces pressure drop across valve, decreases turbulence, and improves flow characteristics. Recommended for applications where bubble-tight seat is required, such as gas transmission, metering, and flow recorders. Pressure rating to 6,000 psi. Precision-machined thread to perfect concentricity, easier operation Stem seal packing uses Viton* O-ring and Teflon* backup ring Bonnet-pin lock prevents accidental removal of bonnet Replaceable Delrin* sleeve insert extends valve life Large-bore straight-through flow allows passage to be rod cleanable Stainless steel roll pin prevents misalignment of the sleeve Bubble-tight shutoff of liquids or gases to 6,000 psi Body and Bonnet Material: 316 stainless steel or AISI 1045 alloy steel Stem Material: 316 stainless steel with stainless steel body, 303 stainless steel with alloy steel body Bonnet Cap (Protective Cover): Polyethylene, beige Pressure Limits: 6,000 psi (42,000 kpa) Temperature Limits: -20º to 200º F (93º C) Packing: Viton* O-ring and Teflon* backup ring Pattern and In-Line Connection Size 316 SST Alloy C V 1/4" NPT N6312 N /2" NPT N6314 N /4" NPT N6332 N /2" NPT N6334 N /4" x 1/2" NPT N6335 N Handle: Two-prong. Stainless steel for stainless steel. Cast aluminum for alloy steel. specifications of Federal Standard H-28. Finish: Stainless steel is passivated. Alloy steel has a clear zinc finish. Assembly: The bonnet-pin lock is standard for all large-bore softseat needle valves. *Viton, Teflon, and Delrin are registered trademarks of DuPont
6 Hard Seat Alloy Steel and Hard Seat 316 Stainless Steel and NACE and A 3-1/16 3-1/16 3-3/4 3-3/4 5-3/ /16 B 1-1/32 1-1/32 1-7/16 1-7/ /16 2-1/32 CF 2-1/16 2-1/16 2-7/8 2-7/8 3-5/8 3-5/8 CM 2-1/16 2-7/32 2-7/ /8 - E /8 1-3/8 1-1/2 2 G 9/16 9/16 27/32 27/32 27/32 27/32 H 21/32 21/32 15/16 15/16 1-5/ /32 A 3-1/16 3-1/16 3-3/4 3-3/4 5-1/4 5-7/8 B 1-1/32 1-1/32 1-7/16 1-7/ /16 2-1/32 CF 2-1/16 2-1/16 2-7/8 2-7/8 3-5/8 3-5/8 CM 2-1/16 2-7/32 2-7/ /8 - E /8 1-3/8 1-1/2 2 G 9/16 9/16 27/32 27/32 27/32 27/32 H 21/32 21/32 15/16 15/16 1-5/ /32 FFA and FFA and A 2-29/ / / /32 4-5/32 5-9/32 B / / /16 C 1-7/16 1-7/ /32 2-7/32 2-3/4 3-7/16 E 7/8 7/8 1-1/8 1-1/4 1-1/2 2 FF / / /32 FM 1 1-7/ / / /32 G 3/8 3/8 3/4 3/4 27/32 27/32 H 5/8 5/8 13/16 13/16 1-1/ /32 A 3-1/16 3-1/16 3-3/4 3-3/4 4-7/8 5-9/16 B 1-1/32 1-1/ / / / /64 C 1-15/ / / / / /64 E 7/8 7/8 1-1/4 1-1/4 1-1/2 2 FF 1-1/32 1-1/ /32 1-3/4 1-25/32 FM 1-1/ / /32 1-3/4 1-25/32 G 3/8 3/8 3/4 3/4 27/32 27/32 H 5/8 5/8 13/16 13/16 1-1/ /32
7 Soft Seat Alloy and Stainless Steel and Miniature Alloy and Stainless Steel and Dimension 1/4 1/2" 1/4" x 1/2" 1 A 3-21/ / /64 6-3/4 B 1 1-1/ /32 CF 2 2-1/2-4-1/16 CM 3-3/8 3-3/4 3-15/32 - D 2-1/2 2-1/2 2-1/2 4-1/2 E 1-1/8 1-1/8 1-1/8 2-1/4 Orifice 3/16 SP 3/16 SP 3/16 SP 5/8 Orifice 7/32 FP 7/32 FP 7/32 FP 5/8 Dimension 1/8 1/4" A 2-1/32 2-1/32 B 61/64 61/64 CF 1-29/ /32 CM 1-29/ /32 D 1-7/8 1-7/8 E 7/8 7/8 Orifice 1/8 1/8 Block/Bleed Terminal Alloy and Stainless Steel Dimension 1/4" 1/2" A 3-1/4 3-1/4 B 1-7/64 1-7/64 C 1-41/ /64 D 2-1/2 2-1/2 E 1-1/8 1-1/8 F 1-9/16 1-9/16 Orifice 3/16 3/16 Dimension 1/2 3/4 x 1/2" A 3-1/2 3-1/2 B 2-11/ /16 C 2-7/64 2-7/64 D 2-1/2 2-1/2 E 1-1/4 1-1/4 Orifice 1/4 1/4
Kerotest/Marsh Needle Valves Series N
Series N Kerotest/Marsh N Series Needle Valves are used in processing plants, oil and gas production, hydraulic and pneumatic equipment, testing labs anywhere the flow of fluid must be carefully regulated.
Kerotest/Marsh Needle Valves Series N
Series N Kerotest/Marsh N Series Needle Valves are used in processing plants, oil and gas production, hydraulic and pneumatic equipment, testing labs anywhere the flow of fluid must be carefully regulated.
ANDERSON GREENWOOD H1 HAND VALVES
Large bore, ⅜ (9.5 mm) diameter orifice, general purpose soft-seated hand valve for pressures to 6000 psig (414 barg) FEATURES GENERAL APPLICATION A general purpose, soft-seated hand valve designed for
P630 HIGH FLOW GAS REGULATOR
P60 HIGH FLOW GAS REGULATOR P60 HIGH FLOW GAS REGULATOR Stainless Steel Internals are Standard Steel Units comply with NACE MR0 Durable Powder Coated Exterior Wide Range of Flow Capacities The P60 is a
ANDERSON GREENWOOD OS&Y GAUGE VALVES SERIES M5K/M5AK/M5YK
SERIES M5K/M5AK/M5YK Root isolation valves with outside screw and yoke, bolted bonnet construction for pressures up to 6, psi (414 barg) FEATURES M5YK GENERAL APPLICATION M5K-L M5K series gauge valves
P133 Pressure Regulator
P33 Pressure Regulator Suitable for Monitoring Balanced Supply Valve Wide Pressure Range Offering The P33 is a direct operated pressure reducing regulator with external pressure registration used in commercial
OpTB TM Trunnion Ball Valve
INTRODUCTION The Optimux OpTB brings the legendary and well proven robustness and dependability of the trunnion ball design to process control applications, no longer limited to a full port option, but
Anderson Greenwood Series F29/F33K primary isolation valves
7 Anderson Greenwood eries F29/F33K primary isolation valves Integrally forged, one piece double block and bleed Keyblok assemblies for primary isolation of pressure take-offs, where the valve is mounted
1.2 REFERENCES.1 American National Standards Institute (ANSI)/American Society of Mechanical Engineers (ASME)
Issued 2005/06/01 Section 15113 Valves Cast Steel: Gate, Globe, Check, Ball Page 1 of 5 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01355 Waste Management and Disposal 1.2 REFERENCES.1 American National
YARWAY HANCOCK CONTINUOUS BLOWDOWN GLOBE VALVE SERIES 5505
Advanced construction features of this high pressure drop angle globe valve provide quality and long service life. FEATURES GENERAL APPLICATION In addition to continuous blowdown service, the Yarway high
1071 Cast Steel Globe Steam Stop Valve (Flanged)
1071 Cast Steel Globe Steam Stop Valve (Flanged) Flanged Ends to DIN 2545 PN 40. Straight Pattern, Outside Screw, Yoke Type, Rising Stem, Bolted Bonnet. Renewable 13% Cr. Stainless Steel (S.S 410) working
1.2 REFERENCES.1 American National Standards Institute (ANSI)/American Society of Mechanical Engineers (ASME).
Issued 2005/06/01 Section 15112 Valves Cast Iron, Gate, Globe, Check Page 1 of 8 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01355 Waste Management and Disposal 1.2 REFERENCES.1 American National Standards
P600 Pressure Regulator
P00 Pressure Regulator The BelGAS P00 series is a direct operated, pressure reducing regulator that can be used as a pressure loaded regulator, switching valve, or monitoring regulator. Available with
Class 125S/200WOG Bronze Gate Valve Non-Rising Stem, Threaded Ends Testing: BS EN 12288, BS 5154, BS EN Working Pressure: PN16
Class 125S/200WOG Bronze Gate Valve Non-Rising Stem, Threaded Ends Testing: BS EN 12288, BS 5154, BS EN 12266 Working Pressure: PN16 FIG. 201 WORKING PRESSURE Working Pressure Non-Shock (psi) Saturated
ball valves 7 Series Fire Safe 2-way, 3-piece Bolted Ball Valves
7 Series Fire Safe 2-way, 3-piece Bolted Ball Valves HOKE s 7 Series Fire Safe Valves meet demanding application requirements in the production environment of chemical and petrochemical processing facilities.
Equipment Catalog. For inquiries and orders, please contact:
Equipment Catalog 1 2 Table of contents...pages Force Flow 100 Lube Pump... 4 Bucket Pumps... 5 Packing Injection Fitting Body Vent (Bleeder) Fittings... 6 1200 & 1500 Lube Pumps... 7 Hose Assemblies Gages
ball valves Ultramite 70 Series Fixed End 2- and 3-way Ball Valves
Fixed End 2- and 3-way Ball Valves Ultramite 70 Series valves are designed to guard against accidental disassembly. The tamper-proof fixed end fittings are welded in place, with the exception of the 7065
1982 Series. Consolidated * Valves. Safety Relief Valve
GE Oil & Gas Technical Specifications 08/2014 Consolidated * Valves 1982 Series Safety Relief Valve A unique design that combines top performance, capabilities and features within an economical, modular
Cryogenic Service Valves
Cryogenic Service Valves Superlok cryogenic valves are used in many industries in a broad range gas service such as oxygen, nitrogen, argon and more. The valves incorporate specialized materials that maintain
A complete LNG FUEling system
A complete LNG FUEling system from the LNG Station Breakaway Coupling CryoMac LNG Fueling Nozzle Cryogenic Hose Quick Disconnect Vent Couplers LNG Tank Receptacle and Fueling Cap to the LNG vehicle Macro
PACK YOUR OWN CAPILLARIES FOR HPLC AND MASS SPEC
PACK YOUR OWN CAPILLARIES FOR HPLC AND MASS SPEC Pack micro-columns of various length and diameter Compact design will not tip on the work surface Seals safely at pressures up to 9000 psi * Assembles simply,
13 Lock tab washer 304 SS 14 Lever and grip Stl-zinc plt-w/vinyl PRODUCT NUMBER
83R-240 SERIES Carbon Steel 3-Piece Full Port Socket Weld Ball Valve With Actuator Ready ISO Mounting Pad 1.5 & 2 Socket Weld, 800 CWP (psig), Cold Non-Shock. 150 psig Saturated Steam. Vacuum Service to
P133 Pressure Regulator
P33 Pressure Regulator Suitable for Monitoring Balanced Supply Valve Wide Pressure Range Offering The P33 is a direct operated pressure reducing regulator used in commercial and industrial applications
MDV SERIES 3 WAY BALL VALVES
MDV SERIES 3 WAY BALL VALVES Diverting ball valves for industrial and process applications. Design Pressure Rating 150# to 1500# Available in Sizes ½ to 12 2500# Available in Sizes ½ to 4 Valve Size 1/2
VALVES & MEASUREMENT. NUTRON TT/TM/TL Forged Steel Trunnion Mounted Ball Valves NUTRON
NUTRON TT/TM/TL Forged Steel Trunnion Mounted Ball Valves NUTRON 2 NUTRON TABLE OF CONTENTS NUTRON tt/tm/tl Forged steel trunnion mounted ball Valves Introduction... 5 MODEL TT Specifications and Compliances...
PACKLESS VALVES. Instrument/Analyzer Products. Catalog 4515/USA April 2003
PACKLESS VALVES Instrument/Analyzer Products Catalog 4515/USA April 2003 PACKLESS VALVES Instrument/Analyzer Products Catalog 4515/USA April 2003 table of contents NV55........................ 1-2 Nova
Page 1 Worldwide Re R v e
Worldwide Page 1 Page 2 Bonnet Non-rotating Metal Stem Tip A non rotating stem tip is typically used in high cycle applications to extend the service life of the valve. Its purpose is to prevent galling
Worcester Controls Series 94, , and The High-Performance Solution for Fugitive Emission, Toxic Gas or High-Cycle Applications
FCD WCABR023-00 (Part PB 94-3) Mass Emission Qualified by Independent Laboratory to EPA Testing Procedures (See Page 2) An ISO 900 Registered Company Series 94, 94-50, 94-300 and 94-600 The High-Performance
M33H ISO Full Bore Ball Valve DN50 to DN200 Flanged ASME 150 and ASME 300
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
SQUARE PORT KNIFE GATE VALVE
SQUARE PORT KNIFE GATE VALVE The SERIES 90 knife gate is a square port low-pressure valve for solid loaded fluids, mainly used in bulk handling and silo outlet applications in industries such as: Power
RHINO VALVES WORLDWIDE. Cryogenic C44/C600 CRYOGENICS
RHINO VALVES WORLDWIDE Cryogenic C44/C600 CRYOGENICS Based on the Series 44, this valve has an extended stem to move away the drops cryogenic temperatures of the operator (human or automatic). This valve
133 Series Self-Operated Regulators
133 Series Self-Operated Regulators z Wide Pressure Range Capability with Single Regulator Type 133H may also use Type 133L springs, allowing pressure settings to be varied between 2-inches wc and 10 psig
1511 Series. Consolidated * Valves. Safety Valve
GE Oil & Gas Technical Specifications 08/2014 Consolidated * Valves 1511 Series Safety Valve Offering proven, high-performance design for low-pressure, steam heating boilers and steam generators, as well
88L-240 Series. Low Temperature Carbon Steel ASME Class 150 Flanged Full Port Ball Valve - 1/2 through 1
88L-240 Series Low Temperature Carbon Steel ASME Class 150 Flanged Full Port Ball Valve - Refer to page D-A MATERIALS OF CONSTRUCTION Description (1/2 & 3/4 Valves) Material 8. Stem Nut 300 Series Stainless
Edward Valves Hermavalve A Zero-Emissions Valve from Edward Valves. V-Rep 95-1
Edward Valves Hermavalve A Zero-Emissions Valve from Edward Valves V-Rep 95-1 David Therneau Design Manager First Published 1995 INTRODUCTION Excellent progress has been made in meeting the requirements
Section 11. API 7500lb Mud Gate Valves
Section 11. API 7500lb Mud Gate Valves Section 11a API 7500lb Rubber Seated Mud Gate Valves Gate Valves are designed and manufactured in accordance with the following specifications:- API 6A ANSI B31.3
ALLOY BALL VALVES 7000 SERIES METAL AND SOFT SEATED 150# TO 2500#
ALLOY BALL VALVES 7000 SERIES METAL AND SOFT SEATED 150# TO 2500# The Jarecki 7000 Series ball valves are available in a variety of materials, end connections, and seat materials. They are a proven in
SV SERIES 2-PIECE V PORT CONTROL VALVES
SV SERIES 2-PIECE V PORT CONTROL VALVES Split Body metal seated control valves for industrial and process applications. Design Pressure Rating 150# Available in Sizes ½ to 12 300# Available in Sizes ½
SAPAG. A full range of API 526 flanged safety relief valves for process applications, gas, steam and liquid. Safety Relief Valve Series 8100/8200
SAPAG A full range of API 526 flanged safety relief valves for process applications, gas, steam and liquid. Features Full compliance to API RP 520 and standards 526, 527. Certified ASME Section VIII on
88A-200 Series. Carbon Steel ASME Class 150 Flanged Full Port Ball Valve -
88A-200 Series Carbon Steel ASME Class 150 Flanged Full Port Ball Valve - MATERIALS OF CONSTRUCTION Description (1/2 & 3/4 Valves) Material 2. Retainer ASTM A108 Type 1215 3. Ball ASTM A108 Type 1215 8.
diaphragm valves DV1 Series 2-Way Diaphragm Valves Typical Applications Analytical Instrumentation Petrochemical Pharmaceutical Chemical
DV1 Series 2-Way Diaphragm Valves The DV1 Series Diaphragm Valves are totally free of springs, bellows, packing, o-rings and lubricants in the process wetted area. Metal-to-metal seals to atmosphere ensure
88A-900 SERIES. Carbon Steel ASME Class 300 Flanged Full Port Ball Valve - 1/2 through 1
88A-900 SERIES Carbon Steel ASME Class 300 Flanged Full Port Ball Valve - 1/2 through 1 For STANDARDS COMPLIANCE and STANDARD FEATURES refer to page D-3. STANDARD MATERIAL LIST PART (1/2 & 3/4 VALVES)
88A-900 Series. Carbon Steel ASME Class 300 Flanged Full Port Ball Valve - 1/2 through 1 STANDARDS COMPLIANCE
88A-900 Series Carbon Steel ASME Class 300 Flanged Full Port Ball Valve - 1/2 through 1 MATERIALS OF CONSTRUCTION Description (1/2 & 3/4 Valves) Material 2. Retainer ASTM A108 Type 1215 3. Ball ASTM A108
Gas Pressure Regulator HON 330
Gas Pressure Regulator HON 330 OPERATING AND MAINTENANCE INSTRUCTIONS/ SPARE PARTS Serving the Gas Industry Worldwide 330.20 EDITION 01/2017 330.20 p. 2 330.20 p. 23 Compensating diaphragm (118,168, 243,
Cosasco Retractable System (Intermediate Pressure Access)
Cosasco Retractable System (Intermediate Pressure Access) COSASCO RETRACTABLE SYSTEM MODEL 6 Features Quick Mounting & Release Simple to Operate Lightweight 5 PSI Working Pressure Convenient Carrying Case
Pressure Regulators K Series
www.swagelok.com Pressure Regulators K Series Pressure-reducing models Back-pressure models Gas cylinder changeover model Vaporizing models Pressure Regulators, K Series 2 Swagelok K Series Pressure Regulator
Pressure Regulators K Series
Pressure Regulators K Series 1 www.swagelok.com Pressure Regulators K Series Pressure-reducing models Back-pressure models Gas cylinder changeover model Vaporizing models 2 Pressure Regulators and Filters
4 1 /2 MARK 73-5 AMERICAN FLOW CONTROL. It s What We Know. AMERICAN-DARLING FIRE HYDRANT AMERICAN-DARLING 4 1 /2 MARK 73-5 FIRE HYDRANT
AMERICAN-DARLING FIRE HYDRANT AMERICAN-DARLING FIRE HYDRANT AMERICAN FLOW CONTROL It s What We Know. CONSTRUCTION AMERICAN-DARLING FIRE HYDRANT OPERATING NUT Cast one-piece bronze operating nut. Design
87A-200 Series. Stainless Steel ASME Class 150 Flanged Full Port Ball Valve - 1/2 through 1
87A-200 Series Stainless Steel ASME Class 150 Flanged Full Port Ball Valve - MATERIALS OF CONSTRUCTION Description (1/2 & 3/4 Valves) Material 2. Retainer ASTM A276 Type 316 3. Ball ASTM A276 Type 316
Regulating valves REG 6-65, REG-SS 15-40
MAKING MODERN LIVING POSSIBLE Technical brochure Regulating valves REG 6-65, REG-SS 15-40 REG are angle-way and straight-way regulating valves, which act as normal stop valves in closed position. The valves
Specification Data CM /10. Putting You In Control Series V-Max. High Capacity V-Ported Control Ball Valve
Putting You In Control Specification Data CM36005 09/10 36005 Series V-Max High Capacity V-Ported Control Ball Valve Dresser Masoneilan 36005 Series V-Max High Capacity V-Ported Control Ball Valve 2 Dresser
87A-100 Series. Stainless Steel ASME Class 150 Flanged Std. Port Ball Valve -
87A-100 Series Stainless Steel ASME Class 150 Flanged Std. Port Ball Valve - 1-1/2 through 2 MATERIALS OF CONSTRUCTION Description Material 1. Body ASTM A351 CF8M 2. Retainer ASTM A276 Type 316 3. Ball
D-1 FIRE PROTECTION PRODUCTS TAPPING VALVE. MUELLER Tapping Valves. MUELLER Tapping Sleeves and Crosses. MUELLER Stainless Steel Tapping Sleeves
TAPPING VALVE MUELLER Tapping Sleeves and Crosses Full range of Tapping Sleeves and Crosses to fit most types of pipe including cast iron, ductile iron, A-C, and cast iron O.D. PVC--Also outlet sealed
World Class Bellows Seal Valves
World Class Bellows Seal Valves Fugitive Emissions Sealing High Cycle Bellows In-Line Servicing High Flow Capacity Conval Bellows Seal Valves meet all of the rigorous requirements of MSS SP-117, ensuring
Table of Contents Scope of Design. Scope of Design Materials Dimensions & Weights Orifice Capacities
Scope of Design CONSOLIDATED Type 1511 safety valves are designed for low pressure, steam heating boilers and steam generators as well as air service applications. Table of Contents Scope of Design......................1511.1
FLY SERIES CONTROL VALVES
FLY SERIES CONTROL VALVES Product Features Fly Series - Control Valves Armstrong Delta2 - FLY SERIES is a globe single seat Control Valve with a robust construction designed for a wide range of process
DEMCO Gate Valves. Dependability, in-line repairability, flexible trim options and drop-tight, position shutoff
DEMCO Gate Valves Dependability, in-line repairability, flexible trim options and drop-tight, position shutoff 1 Table of Contents DEMCO GATE VALVES Introduction... 2 Series DM Gate Valves... 3 Series
NEWCO. Cast Steel Valves. Technical Data TC9308-3
NEWCO Cast Steel Valves Technical Data All the information contained in this manual is the exclusive property of Cameron. Any reproduction or use of the calculations, drawings, photographs, procedures
JRHL Series. Pressure Reducing Valves for Low Flow and Low Pressure Process Gas GAS PRESSURE REDUCING VALVE. Features
JRHL Series Pressure Reducing Valves for Low Flow and Low Pressure Process Gas GAS PRESSURE REDUCING VALVE The JRHL Series line of low flow pressure regulators have the ability to handle low set pressures
83R-200 Series FEATURES STANDARD MATERIAL LIST
83R-200 Series Carbon Steel 3-Piece Full Port Socket Weld Ball Valve With Actuator Ready ISO Mounting Pad 1-1/2 & 2 Socket Weld, 800 psig CWP, Cold Non-Shock. 150 psig Saturated Steam. Vacuum Service to
sanitary control valves & regulators
sanitary control valves & regulators Reputation Built on Quality, Dependability, Service. Get Consistent Quality By involving every employee in our ISO 9001:2000 Quality Assurance Program, you can count
Pre s sure Re gulators
www.swagelok.com Pre s sure Re gulators Pressure-reducing models Back-pressure models Gas cylinder changeover model Vaporizing models Pressure Regulators Swagelok Pressure Regulator Features Stem Fine-pitch
PARTS & ACCESSORIES: EATON DUPLEX BASKET STRAINERS FEATURES OPTIONS MODEL 53BTX DUPLEX (3/4 TO 4 ) MODEL 50 DUPLEX (5, 6, 8 )
PARTS & ACCESSORIES: MODEL BTX & 0 Section 64 Page 64. Issue E FEATURES MODEL BTX DUPLEX (/4 TO 4 ) Dynamic sealing design for long life Easy-to-operate lever handle no gear box required Unique seat and
D I S T R I B U T E D V A L V E S
TABLE OF CONTENTS FEATURES AND BENEFITS Series DM Gate Valves 2 Series DM 7500 Gate Valves 3 Series DT & DB Gate Valves 4 PRODUCT SPECIFICATIONS General Technical Information 6 DIMENSIONS AND MATERIALS
E Spray Drying. industries and NEW markets. challenges. Meeting the. of new WELCOME TO DELAVAN
E Spray Drying Meeting the challenges of new WELCOME TO DELAVAN industries and NEW markets SECTION INDEX Special purpose nozzles for use in the Spray Drying industry covering a wide variety of products.
MDV SERIES THREE WAY BALL VALVES
MDV SERIES THREE WAY BALL VALVES 1/2 THRU 12 ANSI 150# THRU ANSI 2500# FULL PORT AND REDUCED PORT BLOW OUT PROOF STEM METAL AND SOFT SEATS The Jarecki MDV Series ball valves are available in a variety
pressure regulators Single Stage Pressure Regulators Safety Warning Inside Front Cover Index
Index Single Stage Pressure Regulators Safety Warning Inside Front Cover GO Regulator PO Box 4866 Spartanburg, SC 29305-4866 (864) 574-7966 www.goreg.com sales-go@circor.com IFC PR-1 Series 1 PR-2 Series
87A-100 SERIES. Stainless Steel ASME Class 150 Flanged Std. Port Ball Valve through 2
87A-100 SERIES Stainless Steel ASME Class 150 Flanged Std. Port Ball Valve - 1.5 through 2 For STANDARDS COMPLIANCE and STANDARD FEATURES refer to page D-3. STANDARD MATERIAL LIST PART MATERIAL 1 Body
Model and 2 Heavy-Duty Regulator. Regulator Features: Regulator Specifications:
Model 5600 1 and 2 Heavy-Duty Regulator The Model 5600 is a spring-loaded, self-operated pressure regulator, available in 1 and 2 sizes and built to withstand the most difficult processes and environments.
Materials Materials Threaded End Connection Extension, flange and nipples for flanged and socket-weld connections are not shown.
19000 Materials Materials 15 6 9 10 14 7 8 5 7 3 2 4 1 19000-2 Threaded End Connection Extension, flange and nipples for flanged and socket-weld connections are not shown. 19000.5 19000 (SRV-1/Q3.01) 19000
ACCESSORIES LS/520, LC/520 Heavy duty non-return valves 1/ LT1000 Block form flow regulators (uni-directional) 1/8 & 1/4
ESSORIES LT000 lock form flow regulators (uni-directional) /8 & /4 LT00 lock form flow regulators (bi-directional) /8 & /4 LT70 Quick exhaust valves /8 & /4 LS/50, L/50 Heavy duty non-return valves /4...
Pressure Regulators Pressure-reducing models Back-pressure models Gas cylinder changeover model Vaporizing models
www.swagelok.com Pressure Regulators Pressure-reducing models Back-pressure models Gas cylinder changeover model Vaporizing models Pressure Regulators 2 Swagelok Pressure Regulator Features Stem Fine-pitch
1301 Series High-Pressure Regulators
1301 Series High-Pressure Regulators Bulletin 71.1:1301 December 2013 P10 Figure 1. Type 1301F Regulator Features Durable Stainless Steel Diaphragm For high-outlet pressure applications. Spare Valve Disk
Electrical Resistance Monitoring
Electrical Resistance Monitoring (ER) Introduction The electrical resistance (ER) technique is an on-line method of monitoring the rate of corrosion and the extent of total metal loss for any metallic
Fisher NotchFlo DST Control Valve
NotchFlo DST Valve Product Bulletin Fisher NotchFlo DST Control Valve Fisher NotchFlo DST control valves offer excellent control of liquid services with high pressure drops and entrained particulate. The
A. This Section includes the following general-duty valves: 1. Division 15 Section "Mechanical Identification" for valve tags and charts.
D-9 OUTLINE SPECIFICATION FOR HTHW VALVES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
Triple offset valve with metallic seat for High performance. Class 300: 6 to 36 (DN 150 to 900) Design in accordance with EN and ASME B16-34
Type series booklet 8613.1783/4--EN Triple offset valve with metallic seat for High performance Class 300: 6 to 36 (DN 150 to 900) Design in accordance with EN 12516 and ASME B16-34 Applications LNG process
KEYSTONE SLIDE GATE VALVES FIGURE 215
Slide through, O-port gate design for severe service applications FEATURES GENERAL APPLICATION For severe service and specialty applications Pulp and paper Recycle paper Chemical Petrochemical Power Mining
Figure 215. Slide through, O-port gate design for severe service applications. Features
Slide through, O-port gate design for severe service applications Features General Application For severe service and specialty applications Pulp and paper Recycle paper Chemical Petrochemical Power Mining
Apollo Flow Controls A SERIES ALLOY-20 BALL VALVE 1/4-1
399-100-A SERIES ALLOY-20 BALL VALVE 1/4-1 Female NPT Thread, 2000 CWP (psig). Cold Non-Shock. (See referenced P/T chart) 150 psig Saturated Steam. Vacuum Service to 29 inches Hg. FEATURES Investment cast
BULLETIN B NOVEMBER DeZURIK KSV SEVERE SERVICE KNIFE GATE VALVES TECHNICAL SPECIFICATIONS
BULLETIN 51.00-1B NOVEMBER 2016 DeZURIK KSV SEVERE SERVICE KNIFE GATE VALVES TECHNICAL SPECIFICATIONS Materials of Construction Class 150/300 Bonnetless Item Description Material A1 Body Carbon Steel,
Pressure Relief Valves. 1900/P Series. Consolidated Safety Relief Valve
Pressure Relief s 1900/P Series Consolidated Safety Relief Table of Contents Conversion Table..................................................... 1900/P.2 Features & Benefi ts...................................................
PLASTIC FITTINGS Avenue Edmonton, AB Canada T6E 5Z7. Toll Free: Phone: (780) Fax: (780)
9333 45 Avenue Edmonton, AB Toll Free: 1-800-272-9693 Phone: (780) 436-1930 Fax: (780) 435-4849 info@can-con.com TABLE OF CONTENTS PLASTIC FITTINGS POLYETHYLENE PIPE...- 1 - SERVICE RISERS... - 3 - TRANSITION
HDPE WATER CONTROL DEVICES
HDPE WATER CONTROL DEVICES WHY HDPE? HDPE (high density polyethylene) is an extremely rugged thermoplastic that has been used in the water and wastewater industries for decades. Not to be confused with
Meter Swivels Insulated Unions Meter Sets Meter Accessories The Right Connection 1-800-654-3872 1-405-273-6302 www.centralplastics.com : Overview Georg Fischer Central Plastics entered the meter connection
Valbart Through Conduit Slab Gate Valve (TCSGV)
Valbart Through Conduit Slab Gate Valve (TCSGV) The Oil and Gas Industry s Choice for Liquid and Gas Applications Experience In Motion Flowserve Solutions to Keep You Flowing Flowserve is one of the world
VIKING. Heavy-Duty, Foot-Mounted Sealless Internal Gear Pumps. Operating Range1: Nominal Flow Rates: Section 635 Page 635.
Page 635.1 Heavy-Duty, Foot-Mounted Sealless Internal Gear Pumps Operating 1: Series 8124A Model H8124A Nominal Flow Temp. 2 Viscosity (GPM) 15-200 (M 3 /hr.) 3.4-45 (PSI) To 200 PSI (Bar) To 14 Bar (
Process Interface Valves
www.swagelok.com Process Interface s Kenmac Series Process Interface s and Process Monoflanges Stainless steel, carbon steel, and duplex stainless steel materials Pressure ratings in accordance with ASME
Available End Connections & Size Range
ECCENTRIC PLUG VALVES Size Range 3"-24" Water Working Hydrostatic Size Range Pressure psi Test psi 3"-12" 175 350 14"-24" 150 300 Available End Connections & Size Range Figure No. Flanged 3"-24" F-5412
CONOFLOW HIGH-PRESSURE REGULATOR - HP500 Pressure Reducing - Diaphragm Type - High Purity
CONOFLOW HIGH-PRESSURE REGULATOR - HP500 Pressure Reducing - Diaphragm Type - High Purity The HP500 Regulator is a self-contained, diaphragm sensing high purity regulator. A broad offering of materials
Code. 1) Code. Standard or Specification. Bolting
Code 1. Code 1) Code (1) ASME B 31.1 : Power Piping (2) ASME B 31.3 : Process Piping (3) ASME B 31.4 : Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids 2) Material Code Bolting
Solution Partner. Leak - Proof Flow & Control. Needle Valves. W e. s u p p o r t. t h e. i n n o v a t i o n s. o f.
W e. s u p p o r t. t h e i n n o v a t i o n s. o f. c u s t o m e r s Leak Proof low & Control The Best Partner for Value Creation olution Partner Index Needle Valves NV ERIE NV50 eries 4~7 BNV60 eries
2 5 0 P. S. I. G. AMERICAN DARLING 5 1 /4" B-84-B FIRE HYDRANT
2 5 0 P. S. I. G. AMERICAN DARLING 5 1 /4" B-84-B FIRE HYDRANT CONSTRUCTION OPERATING NUT-cast one piece bronze operating nut. Design of the operating thread permits slow closing of the hydrant valve,
Compact Trunnion Mounted Side Entry Ball Valves
Compact Trunnion Mounted Side Entry Ball Valves THAT SQUALITY The Best Guarantee of Safety Perar Ball Valves, One of the first... since 1962 Founded in 1962, Perar is one of the first Italian Manufacturers
DISCOVER VALVES. High-Spec Critical Service Custom Solution CAMERON ORBIT RING-O WKM GROVE GENERAL VALVE ENTECH TBV TOM WHEATLEY TEXSTEAM TK
High-Spec Critical Service Custom Solution DISCOVER VALVES CAMERON ORBIT RING-O WKM GROVE GENERAL VALVE ENTECH TBV TOM WHEATLEY TEXSTEAM TK Cameron brings together the expertise and technology of the world
P R O C E S S V A L V E S. ORBIT Technical Reference Data for Valves and Actuators ORBIT
Technical Reference Data for Valves and Actuators TABLE OF CONTENTS TECHNICAL REFERENCE DATA FOR VALVES AND ACTUATORS Standard Features 2 Ordering Information 3 The Principal 4 One Piece Stem, Enclosed
Section 20. Globe Valves
Section 20 A globe valve is a type of valve used for regulating flow in a pipeline, consisting of a movable disk-type element and a stationary ring seat in a generally spherical body. Globe valves are
ORBIT Valves STANDARD FEATURES
ORBIT Valves STANDARD FEATURES Cameron s ORBIT valves are ideal for applications when zero leakage and frequent operation are demanded. They are used globally in gas processing plants using molecular sieve
Carbon Steel ASME Class 150 Flanged Std. Port Ball Valve through 2
88A-100 SERIES Carbon Steel ASME Class 150 Flanged Std. Port Ball Valve - 1.5 through 2 For STANDARDS COMPLIANCE and STANDARD FEATURES refer to page D-3. STANDARD MATERIAL LIST PART MATERIAL 1 Body ASTM
Original Chiksan Swivel Joints
Original Chiksan Steamlined bore minimizes flow restrictions Smooth, round bore design minimizes turbulence and pressure drop, Longsweep and TripleStep swivel joints have extralong radius elbows that optimize