HIGH TEMPERATURE CERAMIC ADHESIVES & PASTES

Size: px

Start display at page:

Download "HIGH TEMPERATURE CERAMIC ADHESIVES & PASTES"

Isaac Dennis
6 years ago
Views:

HIGH TEMPERATURE CERAMIC ADHESIVES & PASTES Technical Bulletin A A Aremco s high temperature ceramic adhesives are unique inorganic formulations for bonding and sealing ceramics, metals, quartz,

1 HIGH TEMPERATURE CERAMIC ADHESIVES & PASTES Technical Bulletin A A Aremco s high temperature ceramic adhesives are unique inorganic formulations for bonding and sealing ceramics, metals, quartz, graphites, textiles and composite materials used in design, process and maintenance applications to 300 F. These advanced materials, which exhibit high thermal and electrical resistance, enable engineers to solve problems that were impossible previously using conventional epoxies and other organic-based products. A TYPICAL APPLICATIONS Electrical Mechanical Sensors & Instruments Ballast Resistors Catalytic Converters Gas Chromatographs Fiberoptics Ceramic-to-Ceramic High Vacuum Components Gas Ignitors Gasketing/Textiles Liquid Metal Inclusion Counters Halogen Lamps Radiant Heaters Mass Spectrometers Resistance Heaters Refractory Insulation Oxygen Analyzers Rheostats Sagger Plates Strain Gauges Threadlocking Temperature Probes FEATURES P/N Filler General Features Bonding* Principal Use 503 High Fired Strength C-C Dense Ceramics 55 Good Adhesion to Metals C-C, C-M Low CTE Metals, SOFC s 569 RT, Good Filler C-C, C-M Probes, Sensors 600 Alumina Ceramic Fiber-Reinforced C-C Refractory Repair 671 High Adhesive Strength C-C, C-M, M-M Textiles, Threadlocking 835M 835MB High Strength, Good Filler C-C, C-M Halogen Lamps 813A Fiber-Reinforced Sealer C-C, C-M Tundish Nozzles 865 Aluminum Nitride High Thermal Conductivity C-C, C-M Probes, Sensors 668 Alumina- C-C, C-M Oxygen Sensors RT, Good Filler 677 Silica C-C, C-M Induction Coils 690 Boron Nitride Good Fired Strength C-C Boron Nitride 551RN High Adhesive Strength Graphite 669 Ceramic Fiber-Reinforced Graphite, Carbon Structures, Molds Magnesium 571 Dielectric, High Strength Oxide C-M, M-M Heaters, Sensors 618N Silica Low CTE, Good Strength C-C, Quartz Tubes, Vessels, Sensors 516 Dielectric, Moisture Resistant C-C, C-M, M-M Thermocouples 685N Bonds Plated Metals Heaters, Ignitors, to Ceramic C-M Gasketing Zirconia 835 Fiber-Reinforced, C-C, C-M Halogen Lamps RT 885 Bonds and Coats Zirconia, High Strength C-C Zirconia, SOFC s *C-C = Ceramic-to-Ceramic C-M = Ceramic-to-Metal M-M = Metal-to-Metal Aremco s ceramic adhesives are easy-to-use, one- and two-component systems which air dry in 1- hours and are ready for use following a 00 to 700 F cure. These materials are mostly water-based and do not outgas after curing. They are also environmentally safe, non-flammable materials which contain no volatile organic compounds. Ceramabond 671 high temperature threadlocker. Ceramabond 835 bonds halogen bulb. Graphi-Bond 669 bonds graphite fixture. Ceramabond 685 bonds gas ignitor. Ceramabond 503 repairs mullite saggar. Pyro-Putty 677 insulates induction heating coil. AREMCO PRODUCTS, INC. P.O. Box 517, 707-B Executive Boulevard, Valley Cottage, NY (845) FAX: (845) aremco@aremco.com Website: Rev. 1/08

2 A HIGH TEMPERATURE CERAMIC ADHESIVE & PASTE PROPERTIES ➆ Product No A 835M N 551RN ➀ N Trade Name Ceramabond Ceramabond Ceramabond Pyro-Putty Ceramabond Ceramabond Ceramabond Ceramabond Pyro-Putty Ceramabond Graphi-Bond Graphi-Bond Ultra-Temp Ceramabond Ceramabond Ultra-Temp Ceramabond Ceramabond Ceramabond ➄ Aluminum Nitride Boron Nitride Magnesium Oxide Major Constituent Alumina Alumina-Silica Silica Graphite Zirconia Maximum Temperature ➁ ➃ (850) 3000 F ( C) (1650) (1650) (1650) (1371) (1760) (1650) (1650) (1371) (1316) (1650) (985) (1371) (1760) (1371) (1650) (1760) (1760) 700 (148) (1650) CTE, in/in/ F x 10-6 ( C) 4.0 (7.) 4.3 (7.7) 4. (7.6) 4. (7.6) 4.1 (7.4) 4.0 (7.) 4.0 (7.) 4.0 (7.) 4.1 (7.4).33 (.59) 4.1 (7.4) 4. (7.6) 4.1 (7.4) 4.5 (8.1) 4.0 (7.) 4.0 (7.) 7.0 (1.6).0 (3.6) 1.5 (.7) Volume Resistivity, RT (@ 1000 F) 10 9 (10 5 ) 10 8 (10 4 ) 10 9 (10 5 ) 10 9 (10 5 ) 10 8 (10 4 ) 10 9 (10 5 ) 10 9 (10 5 ) 10 8 (10 4 ) 10 9 (10 5 ) 10 9 (10 5 ) NA (NA) NA (NA) 10 8 (10 4 ) 10 9 (10 5 ) 10 9 (10 5 ) 10 8 (10 4 ) 10 9 (10 5 ) (10 9 ) (10 10 ) Dielectric Strength, volts per RT (@ 1000 F) 53 (40) 50 (80) 56 (100) 00 (80) 50 (97) 50 (80) 45 (95) 45 (95) 00 (100) 00 (180) NA (NA) NA (NA) 50 (80) 00 (150) 00 (100) 50 (80) 55 (100) 500 (300) 500 (300) Torque Strength, ft-lbs ➂ NA 8.3 Excellent Excellent Good Excellent Excellent Good Excellent Excellent Excellent Excellent Excellent Good Excellent Good Good Excellent Good Excellent Moisture Resistance ➅ Good Alkali Resistance ➅ Fair Good Good Good Excellent Excellent Excellent Excellent Good Good Good Good Excellent Good Good Good Good Good Good Acid Resistance ➅ Excellent Good Excellent Fair Good Good Good Good Good Good Good Good Good Good Good Good Fair Good Good No. Components Mix Ratio, powder:liquid N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 1.5:1 N/A N/A Viscosity, cps ➂ 43,000 6,000 Paste Paste 84,000 Paste 35,000 Paste 43,000 34,000 Paste Paste 83,000 75,000 Paste Paste 60,000 Paste 6,000 Specific Gravity, gms/cc Air Set, hours < <1 < , 00, 00, 3 00, 00, 00, 00, Heat Cure, F, hrs 500, 500, 00, 00, 3 00, or 00, 00, , 500, 65, 4 00, 500, 00, 3 00, 500, 00, 500, 00, 700, 4/RT 700, 500, 700, 700, 700, Curing Handling Color White White White White White White White White Off White Light Gray Black Black Tan Tan Tan Tan Beige White Gray Shelf Life, Months Storage, F General Notes ❶ Ceramabond 503, 55, 569 and 571 can also be formulated using high purity, fine grain 1-5 micron ceramic powders. Add -VFG to the part number (eg. 503-VFG). Contact Aremco for special pricing. ❷ Custom formulations using cordierite, mullite and other powders are available. ❸ In some cases, specialty pigments in green, black and other colors are available upon request. ❹ All ceramic adhesives except 551-RN contain no volatile organic compounds (VOC s). Reference Notes ➀ Graphi-Bond 551-RN is exported only as a -component system due to shelf life considerations. Order 551-RN-Exp. ➁ Graphi-Bond 551-RN temperature limit is for reducing atmospheres only. ➂ This test is performed after curing for 5 00 F. ➃ Ceramabond 690 operates to 1560 F in an oxidizing atmosphere or to 700 F in a vacuum/inert atmosphere. ➄ Thermal conductivity standard for aluminum nitride is 00 W/m- K (1388 BTU-in/hr-ft - F ) ➅ Properties after firing above 700 F. ➆ A two-part variation of 835M named 835MB is also available. It is particularly good for bonding ceramicsto-quartz. Abbreviations N/A Not Applicable

3 DESIGN GUIDELINES General design criteria for bonding with ceramic adhesives are similiar to those for epoxies and other organic adhesives. Main considerations include the coefficient of thermal expansion, joint design, glue line thickness, operating environment, and an understanding of the suitability of ceramic adhesives. Coefficient of Thermal Expansion Due to the thermal CERAMIC-TO-METAL RECOMMENDED DESIGN shock implicit in most ceramic adhesives applications, the joint design should account for the difference in the coefficient of thermal expansion between the adhesive and the components that are being joined. In the illustration above, note that the poor design loads the ceramic adhesive in tension, since the metal expands faster than the ceramic. The good design allows for this thermal mismatch and loads the adhesive in compression, offering higher reliability. Glue Line Thickness The clearance between mating parts at operating temperature should be -8 mils (50 00 microns). Less than mils will prevent uniform adhesion, and greater than 8 mils will often result in cohesive shear failure within the adhesive. Operating Environment Ceramic adhesives offer excellent electrical, thermal and chemical resistance. In addition, ceramic adhesives, in contrast to organicbased materials, will not outgas under high vacuum. All operating conditions such as temperature, thermal cycling, humidity, corrosion and electrical requirements should be considered before selecting a ceramic adhesive. Joint Design Since ceramic adhesives exhibit relatively poor tensile and shear strength, it is desirable to design a joint that will distribute the mechanical stress. A glue line with greater surface area, such as a tongue-and-groove joint, should be used to reduce joint stress and increase mechanical strength. CERAMIC-TO-CERAMIC RECOMMENDED JOINT DESIGN Ceramic Adhesive Limitations Ceramic adhesives are somewhat brittle and may be affected by dynamic conditions such as vibration and mechanical shock. Expansion joints can be used to relieve stress. Adding ceramic cloth at the interface is also useful. High Vacuum Applications Ceramic adhesives can be used under high vacuum conditions without outgassing. However, vacuum seals are difficult to produce unless the adhesive joint is sealed with a glass or glasslike coating. Refer to Technical Bulletin A5 for Aremco-Seal 617 and 850 glass sealants; refer to Technical Bulletin A11 for Cerama-Bind high temperature inorganic binders. APPLICATION PROCEDURES Follow the guidelines below for applying Aremco s high temperature adhesives. Make sure to read specific application instructions on container before use. Surface Preparation Clean surfaces thoroughly prior to application. Extremely smooth surfaces are difficult to bond and should be roughened whenever possible. Porous substrates tend to absorb the adhesive binders and should be pre-coated with an adhesive thinner. Product thinners are designated by adding a -T to the part number (eg. 503-T). Mixing High temperature adhesives tend to settle in the container and should be mixed thoroughly and slowly to avoid air entrapment. Reduce viscosity as desired using the appropriate product thinner by up to 15% by weight. Two-component systems should be mixed according to the following weight ratios: Ceramabond : 1 Powder to Liquid Graphi-Bond 551RN-Exp 83 : 17 Powder to Liquid Note that Graphi-Bond 551RN-Exp is the export version of 551RN. This product is shipped as a two-component adhesive due to shelf life considerations. Application Apply adhesive to each surface in a thin coat using a brush, spatula or dispenser. Wet the surface thoroughly to ensure good adhesion. Maintain a uniform glue line thickness of -8 mils. Apply even pressure (clamp if possible), and wipe away excess material before drying. A graded adhesive joint is recommended when bonding components which have a gross difference in coefficient of thermal expansion (CTE). First coat each substrate with the adhesive that best matches its CTE, then use a third adhesive with an intermediate CTE to bond the parts together. Example: Bond nickel to silica by pre-coating the nickel with Ceramabond 571 and the silica with Ceramabond 618N. Allow each substrate to air dry and cure at 00 F for 1- hours. Apply Ceramabond 55 as an intermediate adhesive and follow standard instructions in the Curing section. When it is necessary to use an adhesive alternatively as a coating, and several applications are required, allow the substrate to air dry for 1- hours before applying a second coat. A 00 F cure for 1- hours is recommended for each successive coat to avoid blistering. Curing In general all products should be air set for 1-4 hours, then heat cured at 00 F (93 C) for 1-4 hours minimum. Ceramabond 503, 516, 618N and 690 will not dry at room temperature and should be step cured at 00 F (93 C), 500 F (60 C), and 700 F (37 C) for 1- hours at each temperature. Graphi-Bond 551-RN must be cured at 65 F (130 C) for 4 hours to develop maximum strength. Blistering may occur if the glue line is too thick or heating too rapid. Refer to specific product labels for detailed instructions. Safety Read Material Safety Data Sheet carefully before use. All products except Graphi-Bond 551-RN can be washed from the skin with mild soap and warm water. Prolonged skin contact should be avoided to prevent irritation. If any material contacts the eyes, flush continuously with water or neutralizing solutions, then consult a physician immediately. A

A Ceramabond 503 repairs sand core. Pyro-Putty 600 bonds insulation rope. Ceramabond 835 bonds high intensity bulb.

9) X X X X X ALUMINUM NITRIDE 1.5 (.7) X X X X X BERYLLIA (95%) 4.1 (7.4) X X X X X X BORON CARBIDE.6 (4.6) X BORON NITRIDE 4. (3.8) X X X CERAMIC TEXTILES X CORDIERITE 1.1 (1.

9 (5.) X X SILICON NITRIDE 1.8 (3.) X X X STEATITE 4.0 (7.) X X X X X X X ZIRCONIA ZIRCONIA SILICATE REFRACTORIES X ALUMINUM 15.0 (7.0) X X BRASS 10. (18.4) X X CAST IRON 5.9 (10.6) X X X X COPPER 9.

4 A Ceramabond 503 repairs sand core. Pyro-Putty 600 bonds insulation rope. Ceramabond 835 bonds high intensity bulb. CERAMIC ADHESIVE SELECTOR CHART CTE MATERIAL X RN N N A M in/in/ F ( C) CERAMICS METALS ALUMINA (96%) 4.4 (7.9) X X X X X ALUMINUM NITRIDE 1.5 (.7) X X X X X BERYLLIA (95%) 4.1 (7.4) X X X X X X BORON CARBIDE.6 (4.6) X BORON NITRIDE 4. (3.8) X X X CERAMIC TEXTILES X CORDIERITE 1.1 (1.9) X X X GLASS (Borosilicate) 1.8 (3.) X GLASS BONDED MICA 5.8 (10.4) X X X X X GRAPHITE 4.3 (7.7) X X MACOR 5. (9.4) X X X X X X X MULLITE 3.0 (5.4) X X QUARTZ 0.3 (.56) X X X SAPPHIRE 4. (7.6) X SILICON CARBIDE.9 (5.) X X SILICON NITRIDE 1.8 (3.) X X X STEATITE 4.0 (7.) X X X X X X X ZIRCONIA ZIRCONIA SILICATE REFRACTORIES X ALUMINUM 15.0 (7.0) X X BRASS 10. (18.4) X X CAST IRON 5.9 (10.6) X X X X COPPER 9.3 (16.7) INCONEL 6.4 (11.5) X X X MOLYBDENUM.9 (5.) X X X X NICKEL 7. (1.9) X X X X X X X NICKEL-IRON.6 (4.7) X X X X X X PLATINUM 4.9 (8.8) X X SILICON 1.6 (.9) X X X X SILVER 10.6 (19.1) S/S (300 SERIES) 9.6 (17.3) X X X X X X S/S (400 SERIES) 6. (16.6) X STEEL (1010) 6.5 (11.7) X X X X X X X X X TANTALUM 3.9 (7.0) X X X X X X TITANIUM 5.8 (10.4) X X TUNGSTEN.5 (4.5) X X X X X X X Preferred Product For This Application X Applicable Product For This Application Ceramabond 503 bonds Pt/40Rh heater wire on an alumina core. This assembly is part of a hi-temp process furnace used aboard the space shuttle. Ceramabond 503 coats the entire heater assembly and provides oxidation and corrosion protection 1700 C. Refer to Price List for availability of sample kits and complete order information. Aremco Products makes no warranty express or implied concerning the use of this product. The user assumes all risk of use or handling whether or not in accordance with directions or suggestions, or used singly or in combination with other products.

6 R 551-A A T ( 571) mm B 1

7 B R 1) A

HIGH TEMPERATURE CERAMIC & GRAPHITE ADHESIVES

HIGH TEMPERATURE CERAMIC & GRAPHITE ADHESIVES HIGH TEMPERATURE & GRAPHITE S Technical Bulletin A2 Ceramabond 835-M bonds halogen lamp. Ceramabond 503 coats heater used to 1700 ºC. Ceramabond 685-N bonds infrared heater. Graphi-Bond 551-RN bonds graphite