Aluminium Alloy MIC6 Cast Aluminium Tooling Plate
|
|
- Ernest Walter Ellis
- 6 years ago
- Views:
Transcription
1 SPECIFICATIONS Commercial 7000 Series The Best of the Best MIC6 Aluminum Cast Plate is a blend of the most desirable features of many individual metals. The result is a cast aluminum plate that meets the challenge of product accuracy demanded by today's industry. MECHANICAL PROPERTIES Property Value Proof Stress Typical 105 MPa Tensile Strength Typical 166 MPa Elongation A50 mm 3 % Hardness Brinell 65 HB Because of its cast granular structure and stress relieving properties, MIC6 Aluminum Cast Plate allows high-speed metal removal with little, if any, of the distortion commonly inherent in long grained wrought, flat-rolled metals. Using proper aluminum machining methods, tolerances in the thousandths can be consistently maintained. MIC6 Aluminum Cast Plate is finished to 20 microinches typical on both sides. Thickness tolerances is within +/-.005" from nominal on 1/4"- 4". Flatness tolerance is maintained within.015" on 1/4"- 5/8" thickness and.005" on 3/4"- 4" thickness. Thermal Cycling can be performed up to 800 F under controlled conditions. MIC6 Aluminum Cast Plate is produced by continuous casting with each thickness individually cast. By utilizing the most recent developments in casting techniques, the molten metal is continuously fed, eliminating defects from lapses and seams. Thermal gradients are stabilized since heat is removed from both plate surfaces at a balanced rate. The employment of a SNIF filtering and degassing system ensures an end product free of voids and impurities. SUPPLIED FORMS Plate GENERIC PHYSICAL PROPERTIES Property Thermal Conductivity Electrical Resistivity Value 142 W/m.K 36 % IACS CONTACT Address: Unit 29 Beeches Industrial Estate Lavenham Road Yate, Bristol BS37 5QX Tel: Fax: sales@durbinmetals.co.uk Web: REVISION HISTORY Datasheet Updated 15 September 2016 DISCLAIMER This Data is indicative only and as such is not to be relied upon in place of the full specification. In particular, mechanical property requirements vary widely with temper, product and product dimensions. All information is based on our present knowledge and is given in good faith. No liability will be accepted by the Company in respect of any action taken by any third party in reliance thereon. Please note that the 'Datasheet Update' date shown above is no guarantee of accuracy or whether the datasheet is up to date. The information provided in this datasheet has been drawn from various recognised sources, including EN Standards, recognised industry references (printed & online) and manufacturers data. No guarantee is given that the information is from the latest issue of those sources or about the accuracy of those sources. Material supplied by the Company may vary significantly from this data, but will conform to all relevant and applicable standards. As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose, whether expressed or implied. Advice given by the Company to any third party is given for that party s assistance only and without liability on the part of the Company. All transactions are subject to the Company s current Conditions of Sale. The extent of the Company s liabilities to any customer is clearly set out in those Conditions; a copy of which is available on request. [1 OF 9] CONTINUED
2 [2 OF 9] CONTINUED
3 [3 OF 9] CONTINUED
4 [4 OF 9] CONTINUED
5 [5 OF 9] CONTINUED
6 [6 OF 9] CONTINUED
7 [7 OF 9] CONTINUED
8 [8 OF 9] CONTINUED
9 [9 OF 9]
Aluminium Alloy ALUMEC 89 Hot Rolled PLATE
SPECIFICATIONS MECHANICAL PROPERTIES Commercial 7000 Series Property Value Hardness Brinell 146-180 HB Alumec 89 is a high strength aluminium alloy supplied in the form of hot rolled, heat treated plate.
More informationStainless Steel Innosoft - Innoclean - Innoprotect
Innosoft B570 is a special deep cleaner that removes contamination such as oxides/rust from stainless steel surfaces in a single operation. It is a white viscous liquid based on organic acids and surface
More informationStainless Steel St St Butt Weld Fittings
What are Butt Weld Fitttings? - Butt Weld Fittings are a family of fittings used in connecting and creating pipework systems whereby they are welded into the system using circumferential butt welds. They
More informationStainless Steel: EN Standards for Stainless Steel Bar
The old BS970 Parts 1 & 3: 1991 standards have been replaced by a number of EN Standards, the most important of which are shown below EN10088-3Replaces BS970 Part 1: 1991 & BS970 Part 3: 1991 covering
More informationStainless Steel St St Butt Weld Fittings
What are Butt Weld Fitttings? - Butt Weld Fittings are a family of fittings used in connecting and creating pipework systems whereby they are welded into the system using circumferential butt welds. They
More informationStainless Steel - St St Butt Weld Fittings
What are Butt Weld Fitttings? - Butt Weld Fittings are a family of fittings used in connecting and creating pipework systems whereby they are welded into the system using circumferential butt welds. They
More informationStainless Steel - Tube
Tube Size Ranges An almost limitless size range is available with nonstandards being available only in mill production quantities on long lead times. Given below is an indication of what sizes are most
More informationStainless Steel (17/4PH&630) Bar
SPECIFICATIONS Commercial 17/4 PH EN 1.4542 Precipitation hardening stainless steels are chromium and nickel containing steels that provide an optimum combination of the properties of martensitic and austenitic
More informationStainless Steel (17/4PH&630) Bar
SPECIFICATIONS Commercial 17/4 PH EN 1.4542 Precipitation hardening stainless steels are chromium and nickel containing steels that provide an optimum combination of the properties of martensitic and austenitic
More informationStainless Steel (17/4PH&630) Bar
SPECIFICATIONS Commercial 17/4 PH EN 1.4542 Precipitation hardening stainless steels are chromium and nickel containing steels that provide an optimum combination of the properties of martensitic and austenitic
More informationStainless Steel Bar
SPECIFICATIONS Commercial 17/4 PH EN 1.4542 Precipitation hardening stainless steels are chromium and nickel containing steels that provide an optimum combination of the properties of martensitic and austenitic
More informationStainless Steel Innosoft - Innoclean - Innoprotect
Innosoft B570 is a special deep cleaner that removes contamination such as oxides/rust from stainless steel surfaces in a single operation. It is a white viscous liquid based on organic acids and surface
More informationStainless Steel Stainless Steel Glue
Introduction This one-component stainless steel glue, manufactured by Weiconlock, offers rapid and high strength connections without activator. FEATURES One component No activator needed Cure times up
More informationStainless Steel - St St Introduction
Stainless steel is not a single material but the name for a family of corrosion resistant steels. Like many scientific discoveries the origins of stainless steel lies in a serendipitous accident. In 1913
More informationStainless Steel St St Introduction
Stainless steel is not a single material but the name for a family of corrosion resistant steels. Like many scientific discoveries the origins of stainless steel lies in a serendipitous accident. In 1913
More informationACC-U-PLATE. Rolled Plate Performance, Extruded Wide Bar Value. Sapa Industrial Extrusions
ACC-U-PLATE Rolled Plate Performance, Extruded Wide Bar Value Sapa Industrial Extrusions ACC-U-PLATE Highest Quality Extruded Wide Bar in the Industry ACC-U-PLATE offers the best total value for extruded
More informationalimex Product Information
Quality, Flexibility, Knowledge, Experience, Excellence: Solutions in Aluminium Cast Plates. alimex Product Information PROVIDING LEADING-EDGE ALUMINIUM CAST PLATE SOLUTIONS Contents ACP 5080 4-5 ACP 5080R
More informationALUMINUM SHEET AND PLATE RECOMMENDED MINIMUM BEND RADII FOR 90 DEGREE COLD FORMING OF SHEET AND PLATE 1,2,3,4
Material Data The data information contained on this Web site is derived from many different sources. While Central Steel and Wire Company has taken all reasonable steps to ensure that all the information
More informationAluminium Alloy Specifications
Aluminium is the world s most abundant metal and is the third most common element comprising 8% of the earth s crust. The versatility of aluminium makes it the most widely used metal after steel. Aluminium
More information* Outside recommended Brinell hardness testing range (ASTM E 10)
Material Data The data information contained on this Web site is derived from many different sources. While Central Steel and Wire Company has taken all reasonable steps to ensure that all the information
More informationAluminium Alloy Fabrication of Aluminium
Aluminium alloys are normally supplied as semifinished products such as sheet, plate, coil, extrusions, tube or wire. All forms can then be readily fabricated into finished products using a wide range
More informationAll Metals Test Certificates
What is a test Certificate and why is it important? ~ It is effectively a Guarantee that ensures Traceability and protects all parties ~ In many cases the material has no value to a customer unless it
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 14713-2 First edition 2009-12-15 Zinc coatings Guidelines and recommendations for the protection against corrosion of iron and steel in structures Part 2: Hot dip galvanizing
More informationStainless Steel: Stainless Steel in Coastal Environments
The main purpose of this Datasheet is to advise on the choice of stainless steel for use outside in coastal areas in terms of the correct choice of grade and finish. It has been shown after many years
More informationStainless Steel: Stainless Steel in Coastal Environments
The main purpose of this Datasheet is to advise on the choice of stainless steel for use outside in coastal areas in terms of the correct choice of grade and finish. It has been shown after many years
More informationSS-EN ISO 9001 SS-EN ISO 14001
UDDEHOLM FORMAXTM This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty
More informationDryflex CS. TPEs with optimised compression set
Dryflex CS TPEs with optimised compression set CONTENTS INTRODUCTION KEY PROPERTIES GRADE TABLE PROCESSING - EXTRUSION PROCESSING - INJECTION MOULDING PROCESSING CONTACT US INTRODUCTION Dryflex CS is a
More informationCustom 450 Stainless Steel, UNS S45000
Custom 450 Stainless Steel, UNS S45000 Shaped, Flat, Square, Round, Fine Wire, Plated and Bare Wire Specifications: AMS5763, AMS 5773, AMS 5863, ASTM A 564, ASTM A693, ASTM A 959 Custom 450 Alloy Description
More informationCustom 455, UNS S45500
Custom 455, UNS S45500 Shaped, Flat, Square, Round, Fine Wire, Plated and Un-plated Specifications: AMS 5617, AMS 5860, ASTM A313 ASTM A564, ASTM A693 Custom 455 Alloy Description Custom 455 stainless
More informationBS EN Hollow bars for machining Technical delivery conditions Non alloy and alloy steels
BS EN 10294 1. Hollow bars for machining Technical delivery conditions Non alloy and alloy steels 1 Scope This part of EN 10294 specifies the technical delivery conditions for seamless steel hollow bars
More informationDrawn Flat Steel Bars
Page 1 of 10 Viale Certosa, 249-20151 Milano Tel: +39 02 30 700 - Fax: +39 02 38000 346 - Mail: commerciale.riva@rivagroup.com Production Units: Malegno (BS), Italy Page 2 of 10 Products STRUCTURAL AND
More informationSpecification Stainless spring steel
Specification 218-6 Class: Semifinished Products of Steel Class No.:15 Stainless Spring Steel JED 5M Previous Edition Abbreviated Title 21-1 Stainless spring steel 852 5 4 1 Scope The specification refers
More informationOur philosophy at your service
CPC Inox is a leader in stainless steel since 1976 Our philosophy at your service Three production sites in Italy, sales branches in France (CPC Inox France) and Germany (CPC Inox Deutschland): CPC Inox
More informationNominal Analysis (AISI 01) Carbon-.90 Tungsten / / / /32 7/64 1/8
OIL HARDENING PRECISION Ground FLAT STOCK (REGULAR SIZE AND OVERSIZED) STARRETT SERIES 783: 18 Lengths STARRETT SERIES 784: 36 Lengths For Tolerances see page 625. Nominal Analysis (AISI 01) Carbon-.90
More informationDrawn Round Steel Bars. Production Units: Malegno (BS), Italy
Page 1 of 8 Viale Certosa, 249-20151 Milano Tel: +39 02 30 700 - Fax: +39 02 38000 346 - Mail: commerciale.riva@rivagroup.com Production Units: Malegno (BS), Italy Page 2 of 8 Products STRUCTURAL AND GENERAL
More informationDryflex SE. Standard TPE range, optimised for injection moulding
Dryflex SE Standard TPE range, optimised for injection moulding CONTENTS INTRODUCTION KEY PROPERTIES DRYFLEX SE : UNFILLED SERIES DRYFLEX SE : FILLED SERIES DRYFLEX SE : SEMI-FILLED SERIES PROCESSING APPLICATIONS
More information2. Test Records - All records of tests and analysis shall be kept in suitable forms approved by the Bureau.
. Doc: STI/2041/ 2 SCHEME OF TESTING AND INPECTION FOR CERTIFICATION OF STEEL PLATES FOR PRESSURE VESSELS USED AT MODERATE AND LOW TEMPERATURE ACCORDING TO IS 2041:2009 (Third Revision) 1. Laboratory A
More informationNiSPAN-C 902 (Alloy 902), UNS N09902
NiSPAN-C 902 (Alloy 902), UNS N09902 AMS 5221, AMS 5223, AMS 5225 Alloy 902 Wire Description Alloy 902is a precipitation hardenable nickel-iron with a controllable thermoplastic coefficient which is the
More informationMasterPren PVC Waterstops
Range of externally and centrally placed waterstops DESCRIPTION the concreting and vibrating process. It is The MasterPren PVC Waterstop rang is imperative that care is taken to fully compact extruded
More informationContinuous Casting Mould Plates For Slab/ Bloom/ Beam Blank/ Vertical Casters
R Complete Competence in Copper Continuous Casting Mould Plates For / Bloom/ Beam Blank/ Vertical Casters Mould Plate Bloom Mould Plate Beam Blank Mould Plate Casting Bloom Casting Beam Blank Casting s
More informationCOLD ROLLED STEEL S. Automotive. Appliances. Construction. Lighting. Office Furniture
COLD ROLLED STEEL S Automotive Appliances Construction Lighting Office Furniture COLD ROLLED STEELS provide excellent thickness and flatness tolerances, surface finish, and press formability. AK Steel
More informationBorn from fire, made to endure NICKEL ALLOYS
Born from fire, made to endure NICKEL ALLOYS Acroni is the largest slovenian steel manufacturer, which in order to produce steel recycles scrap in an electric arc furnace, casts it on continuous caster
More informationStandard Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip 1
Designation: A 69 06 Standard Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip 1 This standard is issued under the fixed designation A 69; the number
More informationUddeholm Formax. Formax is a trademark registered in Sweden
Uddeholm Formax Formax is a trademark registered in Sweden UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder.
More informationC27200 CuZn37 Industrial Rolled
C272 Alloy Designation EN DIN CEN/TS 13388 (2.321) CW58L JIS C 272 BS CZ 17 UNS C272 Brass Rolled Products KME offers a wide range of brass rolled products in the form of strips, sheets and discs in order
More information3M Electrically Conductive Adhesive Transfer Tape 9707
Technical Data May 2014 3M Electrically Conductive Adhesive Transfer Tape 9707 Product Description 3M Electrically Conductive Adhesive Transfer Tape (ECATT) 9707 is a pressure sensitive adhesive (PSA)
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 6361-1 Second edition 2011-08-15 Wrought aluminium and aluminium alloys Sheets, strips and plates Part 1: Technical conditions for inspection and delivery Aluminium et alliages
More information316Ti Stainless Steel, UNS S31635
316Ti Stainless Steel, UNS S31635 Shaped, Flat, Square, Round, Fine Wire, Plated and Un-plated ASTM A240 316Ti Alloy Description Type 316Ti is a titanium stabilized variation of alloy 316. This austenitic
More informationHot Rolled. AK Steel produces Hot Rolled Steels to meet the strictest chemistry and dimensional requirements, in a wide variety of grades.
Hot Rolled STEELs P r o d u c t D ata B u l l e t i n AK Steel produces Hot Rolled Steels to meet the strictest chemistry and dimensional requirements, in a wide variety of grades. Consistency from coil
More informationSPECIFICATION FOR ALUMINUM-ALLOY DIE AND HAND FORGINGS
SPECIFICATION FOR ALUMINUM-ALLOY DIE AND HAND FORGINGS (Identical with ASTM Specification B 247-95a for the alloys covered except for the deletion of rolled ring forging and editorial differences. Certification
More informationSPECIFICATION FOR STAINLESS STEEL BARS AND SHAPES
SPECIFICATION FOR STAINLESS STEEL BARS AND SHAPES A02 (Identical with ASTM Specification A 276-97.) 1. Scope 1.1 This specification covers hot-finished or coldfinished bars except bars for reforging (Note
More informationMold Design. 12. Mold Materials. Bong-Kee Lee School of Mechanical Engineering Chonnam National University
12. Mold Materials Bong-Kee Lee Chonnam National University Mold Materials easy toolmaking good performance during production good machining properties ease of hear treatment where hardening is required
More informationDNVGL-CP-0248 Edition May 2016
CLASS PROGRAMME Approval of manufacturers DNVGL-CP-0248 Edition May 2016 The content of this service document is the subject of intellectual property rights reserved by ("DNV GL"). The user accepts that
More informationCatalogue of European standards in the aluminium and aluminium alloys field
Catalogue of European standards in the aluminium and aluminium alloys field Under revision New publications during last two years (2017-2018) September 2018 David KRUPKA AFNOR Normalisation Industrial
More informationRegupol mm With Approved Resilient Floor Covering
Regupol 4515 3mm With Approved Resilient Floor Covering PRODUCT INFORMATION SHEET Description Regupol 4515 is a direct stick acoustic system designed to isolate approved Resilient Floor Coverings from
More informationStandard Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip 1
Designation: A69 06 Standard Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip 1 This standard is issued under the fixed designation A69; the number immediately
More informationPerformance, Beauty & Long Life STAINLESS STEEL CARE & MAINTENANCE. Stainless Steel Performance. Stain less Steel
Stainless Steel Performance Stainless Steel Performs Best When Clean Cleanliness of stainless steel is essential for maximum resistance to corrosion. Properly maintained stainless steel provides excellent
More informationNorth American Stainless
North American Stainless Long Products Stainless Steel Grade Sheet AISI 430 UNS S43000 EN 1.4016 INTRODUCTION 430 SS is a plain chromium ferritic stainless steel. With 17% chromium, the steel has good
More informationCopper & Copper Alloys CuZn31Si1 (OF 2270)
Copper and Copper Alloys Page 1 of 5 no responsibility is taken for the correctness of this information 02/2014 Cu Zn Pb Sn Fe Mn Ni Al Si As Co Cr Others min. 66.0 Rem. 0.1 - - - - - 0.7 - - - - max.
More informationHIGH PROTECTION STEEL
is a steel that provides resistance to ballistic impact and explosions. Its advanced protection capabilities are validated by numerous independent and accredited laboratories. is produced in Belgium by
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 22991 First edition 2004-05-01 Gas cylinders Transportable refillable welded steel cylinders for liquefied petroleum gas (LPG) Design and construction Bouteilles à gaz Bouteilles
More informationPaint coatings and properties. Minimum
Sida 1/6 TABLE 1 Paint coatings and properties Indoor/ Outdoor I/O Nom. thickness µm Gloss units Minimum inner bending radius 1) mm Min. temp. during forming C Impact strength J Pencil hardness Resistans
More informationPowerode the universal high performance electrode
the universal high performance electrode Powerode : a dedicated and exclusive process Lebronze alloys has always been committed a process of continuous improvement. This allied with a Research & Development
More information* Outside recommended Brinell hardness testing range (ASTM E 10)
Material Data The data information contained on this Web site is derived from many different sources. While entral Steel and Wire ompany has taken all reasonable steps to ensure that all the information
More informationIdentification. Type Analysis
Page 1 of 16 Unit Display: Metric Print Now Custom 465 Stainless E-Mail Datasheet Add to My Materials Request More Information U.S. Patent Number Identification 5,681,528 5,855,844 UNS Number S46500 Type
More informationBRODER METALS GROUP HTS 316
Broder Metals supply 316 and 316L stainless cold drawn in B8M Class 2, B8M Class 2B, A4-70 and A4-80. A4-70 and A4-80 are named by their minimum tensile strength to be met by the material (70 & 80) by
More information2. TEST RECORDS: All records of tests and analysis shall be kept in suitable forms approved by the Bureau.
SCHEME OF TESTING AND INSPECTION FOR CERTIFICATION OF CARBON STEEL BILLETS, BLOOMS, SLABS AND BARS FOR FORGINGS ACCORDING TO IS:1875-1992 (Fifth Revision) 1. LABORATORY: A laboratory shall be maintained
More informationMetal Forming Process. Prof.A.Chandrashekhar
Metal Forming Process Prof.A.Chandrashekhar Introduction Shaping of a component by the application of external forces is known as the metal forming. Metal forming can be described as a process in which
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 6363-1 Second edition 2012-07-15 Wrought aluminium and aluminium alloys Cold-drawn rods/bars, tubes and wires Part 1: Technical conditions for inspection and delivery Aluminium
More informationISO INTERNATIONAL STANDARD. Mechanical properties of corrosionresistant stainless steel fasteners Part 2: Nuts
INTERNATIONAL STANDARD ISO 3506-2 Second edition 2009-11-15 Mechanical properties of corrosionresistant stainless steel fasteners Part 2: Nuts Caractéristiques mécaniques des éléments de fixation en acier
More informationASTM Standards for Pipe & Fittings
for Pipe & Fittings There are many International Standards for stainless and carbon steel pipes and fittings. The list below is a basic overview of some of these. For more in-depth details of these Standards
More informationISO INTERNATIONAL STANDARD. Metallic materials Tensile testing Part 2: Method of test at elevated temperature
INTERNATIONAL STANDARD ISO 6892-2 First edition 2011-02-15 Metallic materials Tensile testing Part 2: Method of test at elevated temperature Matériaux métalliques Essai de traction Partie 2: Méthode d'essai
More informationSTANDARD FERRITIC STAINLESS STEELS
T e c h n i c a l B r o c h u r e STANDARD FERRITIC STAINLESS STEELS Unity AISI UNS EN U-40910 409 S40910 1.4512 U-430 430 S43000 1.4016 U-430DDQ 430 S43000 1.4016 U-439 439 S43035 1.4510 - S43940 U-1.4509
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 6361-2 Fourth edition 2014-09-15 Wrought aluminium and aluminium alloys Sheets, strips and plates Part 2: Mechanical properties Aluminium et alliages d aluminium corroyés Tôles,
More informationResource Guide. Section 3: Ductile Iron
Resource Guide Section 3: Ductile Iron Section 3 Ductile Iron Description of Grades... 3-3 65-45-12 Ferritic... 3-4 80-55-06 Partially Pearlitic... 3-6 100-70-02 Pearlitic... 3-8 4512 HRDS Heat Resistant...
More informationMETALLIC MATERIAL SPECIFICATION
1. Scope: Page: 1 of 5 1.1. This specification shall be utilized in procurement of AISI 8630 modified steel (UNS G86300) in quenched and tempered condition to 22 HRc maximum hardness. 1.2. These materials
More informationISO INTERNATIONAL STANDARD. Railway components Technical delivery requirements Part 2: Non-alloy carbon steel baseplates
INTERNATIONAL STANDARD ISO 6305-2 Second edition 2007-02-15 Railway components Technical delivery requirements Part 2: Non-alloy carbon steel baseplates Éléments constitutifs de la voie ferrée Spécifications
More informationCHARACTERISTICS / ADVANTAGES
PRODUCT DATA SHEET Flexible PVC Waterstops PRODUCT DESCRIPTION Flexible PVC waterstops used to seal construction and expansion joints in concrete structures. Sika -Waterbars are available in different
More informationT :
Aluminium Stock www.cncdirect.co.nz T : +64 9 622 2169 www.highgrademetals.co.nz About CNC Direct Limited was established by David Thumath in 2007 to supply quality well priced machine tools into the New
More informationRailway rolling stock materials
BRITISH STANDARD BS 5892-3: 1992 Incorporating Amendment No. 1 Railway rolling stock materials Part 3: Specification for monobloc wheels for traction and trailing stock ICS 45.040 Committees responsible
More informationLicensed Copy: John May, Powertrain Ltd., February 20, 2002, Uncontrolled Copy, (c) BSI
BRITISH STANDARD BS 70-3: Incorporating Amendment Nos. 1 and 2 Specification for Wrought steel for mechanical and allied engineering purposes Part 3: Bright bars for general engineering purposes BS70-3:
More informationWear-resistant steels. Technical terms of delivery for heavy plates. voestalpine Grobblech GmbH
Wear-resistant steels Technical terms of delivery for heavy plates voestalpine Grobblech GmbH www.voestalpine.com/grobblech Wear-resistant steels durostat durostat 400 durostat 450 durostat 500 durostat
More informationENAMELING STEELS PRODUCT DATA BULLETIN
ENAMELING STEELS PRODUCT DATA BULLETIN Appliances Plumbingware Barbecue Grills Architectural AK Steel manufactures three enameled products to meet a variety of porcelain enameling and formability requirements:
More informationCopper & Copper Alloys CuZn38Pb2 (OF 2361)
Copper and Copper Alloys Heiligenstraße 70 41751 Viersen Phone +49 2162 956-6 FAX +49 2162 956-762 duelken@otto-fuchs.com Page 1 of 5 no responsibility is taken for the correctness of this information
More informationCrystal Cast 1000A : Crystal Cast 1000B By Weight 100 : 120. Appearance - Clear liquid Clear liquid Clear liquid
Crystal Cast 1000 Two Part Casting System Water Clear, UV Stable Crystal Cast 1000 is a two component thermoset system which is water clear when cured. Crystal Cast 1000 is ideal for rapid prototyping,
More informationElectrolytic Tinplate
Flat Products Electrolytic Tinplate http://www.nssmc.com/ 2-6-1 Marunouchi, Chiyoda-ku,Tokyo 100-8071 Japan Tel: +81-3-6867-4111 Electrolytic Tinplate C003en_03_201707f 2012,2017 NIPPON STEEL & SUMITOMO
More informationBUREAU OF INDIAN STANDAD. Draft Indian Standard FREE CUTTING COPPER BARS, RODS AND SECTIONS SPECIFICATION (First Revision of IS 8328) ICS
For BIS use only BUREAU OF INDIAN STANDAD Draft Indian Standard FREE CUTTING COPPER BARS, RODS AND SECTIONS SPECIFICATION (First Revision of IS 8328) ICS 77.150.30 Not to be reproduced without permission
More informationISO 185 INTERNATIONAL STANDARD. Grey cast irons Classification. Fontes à graphite lamellaire Classification. Second edition
INTERNATIONAL STANDARD ISO 185 Second edition 2005-08-15 Grey cast irons Classification Fontes à graphite lamellaire Classification Reference number ISO 185:2005(E) ISO 2005 PDF disclaimer This PDF file
More informationWear-resistant steels. Technical terms of delivery for heavy plates. voestalpine Grobblech GmbH
Wear-resistant steels Technical terms of delivery for heavy plates voestalpine Grobblech GmbH www.voestalpine.com/grobblech Wear-resistant steels durostat durostat 400 durostat 450 durostat 500 durostat
More informationTMG PC Strands, Wire & Bar
TMG PC Strands, Wire & Bar TMG PC Strands Low Relaxation Strands TMG 7-wire Low Relaxation Strands is renowned for its high quality and reliability. Our ability to meet numerous international standards
More informationWith Dura-Bar you will be able to:
Dura-Bar Stock List Dura-Bar is an engineered iron designed to meet our customers most critical requirements. It is manufactured to strict process controls that provide world-class quality and uncompromising
More informationTM 1020:2017. Determination of the long term Thermal Conductivity of an OCF 1 Canister Foam
FEICA - OCF TEST METHOD Brussels, 31 January 2017 TM 1020:2017 Determination of the long term Thermal Conductivity of an OCF 1 Canister Foam 1. Scope This method describes how to determine the long term
More informationRegupol K225 5mm Impact Sound Acoustic Underlay for Engineered Timber Floors
Regupol K225 5mm Impact Sound Acoustic Underlay for Engineered Timber Floors PRODUCT INFORMATION SHEET Description Regupol K225 is an impact sound acoustic underlay designed to isolate engineered timber
More informationTABLE OF CONTENTS. Hot Roll (Angles, Beams, Channels, Flats, Squares, Rounds) 3. Pipe, Pipe Tube, Tube. Sheets & Plates
DRI1529-McNeilus-Revised 12/12/05 12:18 PM Page 1 McNeilus Steel, Inc. TABLE OF CONTENTS Page Hot Roll (Angles, Beams, Channels, Flats, Squares, Rounds) 3 Cold Roll (Flats, Hex, Rounds) 17 Pipe, Pipe Tube,
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 8535-1 Fourth edition 2006-08-01 Diesel engines Steel tubes for highpressure fuel injection pipes Part 1: Requirements for seamless cold-drawn single-wall tubes Moteurs diesels
More informationLecture 7. Chapter 13. Rolling of Metals. The process of reducing thickness of changing the cross-section 90% of all metals produced by metalworking
Lecture 7 Chapter 13 Rolling Rolling of Metals The process of reducing thickness of changing the cross-section 90% of all metals produced by metalworking Changes microstructure Larger grains small grains
More informationISO 185 INTERNATIONAL STANDARD. Grey cast irons Classification. Fontes à graphite lamellaire Classification. Second edition
INTERNATIONAL STANDARD ISO 185 Second edition 2005-08-15 Grey cast irons Classification Fontes à graphite lamellaire Classification Reference number ISO 2005 Provläsningsexemplar / Preview PDF disclaimer
More informationMARSHALLOY MQ /FM. The Deluxe Company. Technical Bulletin
The Deluxe Company Technical Bulletin Dear Industry Colleagues, Precision Marshall Steel Company s primary mission is to provide higher value in the products and services we provide than can be found from
More informationThe Convenience Stores For Metal
STEEL BARS Data and Specifications C1018 Cold Finished Bar A low carbon steel with medium manganese content. Applications: Cold forming and bending operations (for severe bends stress relieving may be
More informationIMPACT. Chemical composition For the chemical composition of the ladle analysis the following limits are applicable (in %):
IMPACT Wear resistant steel Material data sheet, edition April 2016 1 DILLIDUR IMPACT is a wear resistant steel with a nominal hardness of 340 HBW in delivery condition. DILLIDUR IMPACT is not a constructional
More information