GE Healthcare. R/F Site Planning. Customer Site Readiness Requirements. Drawing Index

Transcription

1 Drawing Index These sheets are a document set and should not be separated. Electrical information and references are contained on all sheets. GE Healthcare Customer Site Readiness Requirements Any deviation from these drawings must be communicated in writing to and reviewed by your local GE Healthcare Installation Project Manager prior to making changes. Make arrangements for any rigging, special handling, or facility modifications that must be made to deliver the equipment to the installation site. If desired, your local GE Healthcare Installation Project Manager can supply a reference list of rigging contractors. New construction requires the following; 1. Secure area for equipment, 2. Power for drills and other test equipment, 3. Capability for image analysis, 4. Restrooms. Provide for refuse removal and disposal (e.g. crates, cartons, packing) Contact a radiation physicist or consultant to specify radiation containment requirements. GE Equipment Delivery Requirements Items 1 through 8 on the GE Healthcare Site Readiness Checklist are REQUIRED to facilitate equipment delivery to the installation site. Equipment will not be delivered if these requirements are not satisfied. GE Healthcare Site Readiness Checklist These equipment installation drawings indicate the placement and interconnection of the listed equipment components. These drawings are not construction or site preparation drawings. Customer remains ultimately responsible for preparing the site to accommodate the installation and operation of such equipment in compliance with GE Healthcare's written specifications and all applicable federal, state, and/or local requirements. Item # GEHC Global Order # : Customer: GEHC On-site Representative : MI Supplier: Name of customer reviewed with : Lead Installer: GEHC PMI : Phone Number: Target Site Prep Completion Date: Helper: The customer is responsible for proper site preparation and site readiness regardless of any GEHC inspections/assessments. Inspection Date GEHC Minimum Requirements Storage: Is item ready? Predict (Pre-ship) Is this item ready? Will item be ready? Verify (Delivery): Is item ready? Validate (Mech Install): Is item ready? Comments If "N", please enter in comments or action plan * REQUIRED REFERENCE * 1 Equipment installation drawings must match actual room size and must meet clearance requirements. Deviations that meet installation requirements may be red-lined, if red-lining is allowed by local code. Seismic requirements are identified on construction drawings. 2 Delivery route to installation or storage area meets requirements and has been discussed and scheduled with the customer. Ensure floor protection is discussed, requirements identified, and will be available at time of delivery and installation. Preinstallation Manual R/F Site Planning 3 4 Rooms that will contain equipment, including storage areas, are dust free. Room security to prevent unauthorized access and theft has been discussed with customer. The customer is aware of these security issues, implications and responsibility. In room HVAC ductwork and units (in room) must be mechanically installed and dust free. Installation rooms appear to meet environmental conditions (see Further Definitions) and observed issues have been communicated to the customer. If being stored, storage area must meet PIM storage criteria. 5 Ceiling grid is installed, Unistrut is located per the installation drawings, and permanent lighting is installed and operational. A mandatory component of this drawing set is the GE Healthcare Preinstallation manual. Failure to reference the preinstallation manual will result in incomplete documentation required for site design and preparation. Preinstallation documents for GE Healthcare products can be accessed on the web at: Floor is clean and prepared for final floor covering. Customer has verified floor leveling meets the equipment installation drawings and PIM specs and no visible defects are observed. Gantry and table baseplate are installed prior to delivery (if applicable) Access to a working phone at the facility for emergency use, including MR magnet delivery. All walls primed (final coat not needed on Day 1), and counter tops that will support equipment must be installed. No dustproducing cabinetry work in installation areas. Mechanical supplier has been provided with a set of equipment installation drawings for reference. For California, permitted construction drawings or PMI-specified installation drawings are required. Conduit/electrical cable ducting/dividers/ access flooring installed, with the exception of surface-mounted floor ducting. Wiring to the main disconnect panel is installed and compliant with equipment installation drawings or pre-installation manual. Issued Date: 7/9/07 Rev 11

2

3

4

5

6

7

8

9