Product, Design and Installation Guide. Rainwater Systems FOR RESIDENTIAL, COMMERCIAL AND INDUSTRIAL APPLICATIONS

Transcription

1 Uniclass JR11 L7313 CI/Sf (52.6) In6 February 2007 RW109 EPIC 52 X71 Rainwater Systems Product, Design and Installation Guide FOR RESIDENTIL, COMMERCIL ND INDUSTRIL PPLICTIONS Intelligent Solutions for bove Ground Projects

2 PVC-U RINWTER SYSTEMS Introduction to OSM - from Wavin OSM From Wavin OSM, from Wavin Plastics Limited, is the leading name in plastic systems for building, construction and utilities. The OSM product range is unrivalled in scope and quality, covering: bove Ground systems Plumbing and Heating systems elow Ground Drainage systems Water Management systems Quality assured products OSM systems are the benchmark for excellence and product innovation: precision-manufactured in the UK using the most advanced injection moulding and extrusion machines. ll products comply with or exceed relevant ritish and European standards to ensure reliability and long-lasting service. Intelligent connections OSM systems offer integrated solutions. This enables specifiers and installers to assemble complete drainage, plumbing and heating, and pressure pipe systems from a single source, with complete confidence in compatibility and performance. ll systems are backed by comprehensive technical support and a nationwide distribution network to ensure availability when and where required. Wavin is a leading European manufacturer of industrial plastic products, and one of the largest producers of plastic pipe and fittings in the world. Wavin is credited with inventing and pioneering the use of plastic pipe for water distribution in the mid 1950s. Constant research and development has enabled Wavin to maintain its position at the forefront of plastics technology. Environmental responsibility Wavin Plastics Limited has S EN ISO 9001: 2000 SI status and was the first plastic pipe manufacturer to be accredited to S EN ISO Environmental Management Systems. Wavin Plastics Limited is committed to environmental responsibility, and is a leading pioneer of systems to conserve and control water. In production, the Company recycles the majority of waste materials, and sets annual targets for energy efficiency audited by the certifying body. Passion and resourcefulness ll Wavin personnel are committed to providing a comprehensive, responsive service and are passionate about delivering total Customer satisfaction. Wavin Plastics Limited maintains an industry-wide dialogue and rigorous assessment of all procedures to ensure that Wavin product development and product support accurately addresses the needs of all Customers today and into the future. 2 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

3 PVC-U RINWTER SYSTEMS Product, Design and Installation Guide: Contents Contents Introduction OSM Gutter Profile 4 5 OSM Downpipe Range 5 Selection Guidance Gutter Flow Capacity/Roof reas 6 System Selector & Compatibility Chart 7 System Components Chart 8 9 OSM PVC-U RINWTER SYSTEMS Half-round Gutter Systems RoundLine Gutter components Pipe components SuperLine Gutter components Pipe components RoofLine Gutter components Pipe components Minifit Gutter components Pipe components Semi-elliptical Gutter System DeepLine Gutter components Pipe components Square/Profiled Gutter Systems Squareline Gutter components Pipe components StormLine Gutter components Pipe components 15 18/40 43 Flat roof and alcony System OSM Roof outlets Outlet components 48 Pipe components ncillaries and Spares Components Design Procedures Gutters Determining Gutter Flow Capacity Gutter Support 56 Gutter Jointing 57 Connections to other Gutter types 57 Downpipes Pipe Support 58 Design Detailing Typical connections of Gutter Outlets to OSM pipe Connections to other materials 61 Connections to G drainage 62 Flat roof and alcony Drainage OSM Roof Outlets 63 Physical Characteristics Materials: Properties & Performance 63 SITEWORK Good Site Practice Handling, storage, safety, maintenance 64 General Techniques Gutter installation Gutter jointing Gutter support Pipe installation Pipe cutting and jointing Pipe support and offsets Connections to: - elow ground drainage existing iron pipe 76 Flat roof drainage OSM Roof Outlets 76 REFERENCE General information 77 Index Product Data Sheet 81 Would you like more info 82 Technical advice and assistance 83 OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 PVC-U RINWTER SYSTEMS Introduction to OSM from Wavin Contents 3

4 PVC-U RINWTER SYSTEMS Range Introduction: Gutter Profiles Half-Round Gutter Systems RoundLine 112mm (4 1 /2") Half-round gutter system Classic, simple shape Introduction to the range Ideal for domestic/housing projects For roof areas up to a maximum of 163m 2 with one downpipe Connects to 68mm (2 1 /2 ) circular GUTTER PROFILES The OSM range offers a choice of seven rainwater gutter profiles to meet the varying aesthetic, performance and installation requirements for all types of building, from single dwelling to large residential, commercial or industrial premises. In addition, OSM Roof Outlets provide efficient and reliable drainage for flat roofs. These pages provide an overview of the OSM range to help specifiers select the most appropriate system for a specific project. For flow capacities, see page 6. downpipe vailable in lack, Grey, White and rown SuperLine 125mm (5") Half-round gutter system Versatile system offering excellent volume removal rate Suitable for large domestic roof areas and small commercial buildings For roof areas up to a maximum of 250m 2 with one downpipe Connects to 68mm (2 1 /2 ) circular downpipe vailable in lack and rown RoofLine 150mm (6") Half-round gutter system Very high capacity in a classic profile Suitable for large commercial and industrial buildings For roof areas up to a maximum of 317m 2 with one downpipe Connects to 110mm (4 ) circular downpipe vailable in lack and Grey Mini-Fit 75mm (3") Half-round gutter system Small profile Suitable for porches, conservatories, sheds, garages and other small roof areas For roof areas up to a maximum of 49m 2 with one downpipe Connects to 55mm (2 ) circular downpipe vailable in Grey and rown 4 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

5 PVC-U RINWTER SYSTEMS Osma Rainwater : Gutter Profiles Roof Outlets Downpipes Semi-Elliptical Gutter System DeepLine 113mm (4 1 /2") Semi-elliptical gutter system Compact gutter with high capacity Suitable for domestic and small commercial buildings For roof areas up to a maximum of 299m 2 with one downpipe Connects to 68mm (2 1 /2 ) circular downpipe vailable in lack, Grey, White and rown 113 Square/Profiled Gutter Systems 76 Roof Outlets OSM Roof Outlets 82mm and 110mm Domed Roof Outlets For flat roofs May be installed in mastic asphalt or built-up roofing For roof areas up to a maximum of 143m 2 for 82mm outlet 209m 2 for 110mm outlet with one downpipe Connects to 82mm and 110mm circular downpipe SquareLine 100mm (4") Square section gutter system Smart, efficient rectilinear profile Suitable for domestic buildings For roof areas up to a maximum of 178m 2 with one downpipe Connects to 61mm (2 1 /2 ) square and (via adaptor) 68mm (2 1 /2 ) circular downpipe, installed either flush to the wall or off the wall vailable in lack, White and rown pprovals S EN 607: 2004 Eaves gutters & fittings - PVCu. Definitions, requirements and testing. pproved Systems: RoundLine, Deepline, SuperLine, RoofLine, SquareLine*, StormLine*. StormLine 111x76x97 (4 1 /4x3 3 /4 ) Ogee profile gutter system Distinctive, high capacity ogee profiled design High front edge to prevent water overshoot Higher capacity to cope with increased rainfall levels For roof areas up to a maximum of 254 m 2 Connects to both 68mm (2 1 /2 ) circular downpipe and 61mm (2 1 /2 ) square downpipe vailable in lack, White and rown S EN 1462: 2004 Gutter brackets. Classification, requirements & testing. pproved Systems: RoundLine, Deepline, SuperLine, RoofLine, SquareLine, StormLine. S EN : 2000 Plastics rainwater piping systems for above ground external use - PVCu. pproved Systems: Round pipes 68, 82 and 110mm. Square pipe 61mm. *Gutter only Downpipes Circular Pipe (ll dimensions in millimetres) Nominal Outside Dimension Wall Thickness System Usage Size Min Max Min Max Mini-Fit RoundLine, DeepLine, SuperLine, StormLine Domed Roof Outlets RoofLine and Domed Roof Outlets Downpipes Square Pipe (ll dimensions in millimetres) Nominal Outside Dimension Wall Thickness System Usage Size Min Max Min Max SquareLine, StormLine OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEMS Range Introduction: Gutters Roof Outlets Downpipes 5

6 PVC-U RINWTER SYSTEMS OSM Rainwater Systems: Selection Guidance Selection Guidance The next few pages provide a quick-reference system selector for typical building types (page 7). For other projects, or if you need to check capacity requirements in more detail, see below and roof area calculations (opposite). NOTE: For full capacity and flowrate information, see pages The main factors Rainwater system selection firstly needs to consider: Volume of water to be managed by the system this defines the required capacity of the rainwater system to be installed. Required capacity This is determined by: Type of building Roof area to be drained nticipated rainfall level NOTE: uilding Regulations require allowance for a 1 in 30-year storm Steps to selection System selection is decided by: System capacity: its ability to handle the required capacity ppearance: gutter profile shape and colour System capacity This is dependent on: Gutter capacity (flow in litres per second) according to size and profile shape, but also influenced by: How the gutter is laid with a gradient (FLL), or LEVEL Number of outlets Location of outlets at the END, or in the CENTRE, of the gutter run System capacity will be less if the gutter is laid level, rather than with a fall includes an angle, rather than a single straight run outlet is at the end of the run rather than mid-run For a quick-reference comparison of system capacity for each OSM system, see page 5 If in doubt or if your project is not a typical building/size Calculate maximum roof area to be drained If you still require advice, call the Wavin Technical Hotline: How many brackets? Whichever system you select, you ll need: Gutter Support rackets 3 per 4m gutter length when using Gutter Jointing rackets 4 per 4m gutter length when using Gutter Unions NOTE: Increase number of brackets if allowing for snow-loading Simplified method Measure the roof plan area ( x ) in sq. metres Multiply the area by the appropriate roof pitch factor Shallow (approx. 30º): 1.29 Normal (approx. 45º): 1.50 Steep (approx. 60º): 1.87 EXMPLE: = 5m and = 12m. Shallow pitch: 30º Roof plan area: 5m x 12m = 60m 2 Effective roof area:60 x 1.29=77.4m 2 Pipe Support rackets 1 per 2m downpipe length How long? Downpipe Standard 2-storey house: 5.5m length ungalow: 2.75m length Maximum effective roof area for each system Having calculated the effective roof area to be drained Check which OSM systems have sufficient capacity Maximum effective roof area (m 2 ): gutter laid to 1:600 fall Running outlet position t END of gutter t CENTRE of gutter Flow capacity litres/sec RoundLine SquareLine StormLine StormLine DeepLine SuperLine RoofLine NOTE: System capacity/performance capability is reduced if the roof includes valleys, dorma windows, steep pitch, or With SquareLine downpipe Guttering is laid level (reduction approx %), or Gutter includes an angle (reduction approx. 15%) With RoundLine downpipe 6 CUSTOMER SERVICES TECHNICL ENQUIRIES FX EMIL info@wavin.co.uk

7 PVC-U RINWTER SYSTEMS OSM Rainwater Systems: System Selector Compatibility Table System Selector DOMESTIC High capacity INDUSTRIL COMMERCIL Gutter Profiles RoundLine SquareLine StormLine DeepLine SuperLine RoofLine Gutter Profiles Maximum Roof rea Downpipe Systems Maximum 115m 2 148m 2 212m 2 220m 2 180m 2 310m 2 Roof rea 68mm 61mm 68mm 61mm 68mm 68mm 68mm 110mm Downpipe Systems Colour Choice Colour Choice 1930 s Semi 3-ed Detached partment lock Conservatory arn/ gricultural Recommended lso suitable Terrace 3-Storey Townhouse Luxury Detached Offices Warehouse Compatibility Table OSM RoundLine SquareLine StormLine DeepLine SuperLine RoofLine FloPlast Hepworth Hunter Marley Compatibility table Marshall Tufflex Polypipe Terrain YES YES YES YES 1 YES YES No equivalent No equivalent No equivalent No equivalent No equivalent No equivalent No equivalent No equivalent No equivalent No equivalent No equivalent No equivalent No equivalent No equivalent No equivalent YES YES No equivalent YES YES YES YES 2 No equivalent No equivalent No equivalent No equivalent No equivalent No equivalent No equivalent No equivalent YES YES NO No equivalent YES YES rett YES No equivalent No equivalent YES No equivalent No equivalent 1 Marley Clipmaster only (Marley Premier NOT compatible) 2 daptor required OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 PVC-U RINWTER SYSTEMS Selection Guidance: System Selector Compatibility Table 7

8 PVC-U RINWTER SYSTEMS System Component Chart Gutter Profiles Key Gutter Fittings Half-round gutter systems RoundLine 112 Size (mm) G W N Colour Jointing racket Union Support Rise and Fall Rafter rackets Rafter (djustable) (See KEY) Outlets Hanging Connectors Running Stopend a b d ngles SuperLine 125 N RoofLine 150 G Mini-Fit 75 G N Semi-elliptical gutter system DeepLine 113 G W N Square/Profiled gutter systems SquareLine StormLine x 97 W N W N - - c e Flat roof and balcony system Roof Outlets - G Colour Key Colour lack Grey White rown Ref. Code G W N 8 CUSTOMER SERVICES TECHNICL ENQUIRIES FX EMIL info@wavin.co.uk

9 PVC-U RINWTER SYSTEMS System Component Chart Downpipes Key Pipe Fittings Circular Pipe 55mm 68mm 82mm 110mm Square Pipe 61mm rackets Pipe Socket Pipe or Socket Drive-in Ext./Spacer Connectors (See KEY) ends Offset Long Tail Offset 87 1 /2 ranches 67 1 / /2 ccess ccess Pipe k l r f g h i j f g h i j f f g h i j - * h i j m n p q Square Round h i j m n p q - - f g h i j k Key Gutter Connectors a Connector to 4 or 4 1 /2 cast-iron half-round gutter b Connector to 4 1 /2 cast-iron ogee gutter c Connector to 4, 4 1 /2 or 5 cast-iron ogee gutter L/H and R/H versions d Connector to PVC-U true half-round gutter e Connector to 4 1 /2 RoundLine Gutter Pipe Connectors and daptors f Pipe Connector g Connector to 2 1 /2 cast-iron rainwater pipe h Connector to 82mm PVC-U Drain Socket i Rainwater daptor 68mm pipe to 110mm PVC-U drain j Universal Drain daptor k P/E Connector to cast-iron spigot l S/S Connector to cast-iron or clay drain socket m Pipe Connector and racket n Pipe Connector and racket Stand Off p Drain daptor Square-to-Round q Outlet daptor Square-to-Round Reducer r S/S Reducer Standard Saddle racket Stand Off racket * Via Square-to-Round Outlet daptor lso 45º end OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 PVC-U RINWTER SYSTEMS System Component Chart 9

10 PVC-U RINWTER SYSTEM: RoundLine Half-round 112mm gutter system: Gutter Gutter Union rackets Gutter RoundLine Gutter NOMINL PRT LENGTH [m] NUMER 112 0T T074 4 COLOURS: lack, Grey, White, rown Gutter Union and Jointing racket Gutter Union Use with Gutter Support rackets 0T019/0T039 (see below), Top/Side Rafter rackets (page 11) or Rise-and-Fall rackets (page 11), with EPDM seals 112 0T COLOURS: lack, Grey, White, rown Gutter Jointing racket Used to join running lengths of gutter and fixing to fascia, with EPDM seals 112 0T COLOURS: lack, Grey, White, rown Support rackets and Spacers Gutter Support racket For support centres, see page T COLOURS: lack, Grey, White, rown Gutter Support racket 3 screw fixing For support centres, see page T COLOURS: lack, Grey, White, rown Gutter racket Spacer Use with Support rackets 0T019 or 0T039 (see above) to provide additional 21mm clearance - 0T COLOURS: lack, Grey, White, rown 10 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

11 PVC-U RINWTER SYSTEM: RoundLine Half-round 112mm gutter system: rackets Connects to 68mm circular downpipe (page 15) Support rackets and Spacers continued ngled racket Spacer 22 1 /2 angle Use with Support racket 0T019 (page 10) when fascia board or rafter/truss ends are angled MTERIL: Polypropylene - 0T COLOURS: lack Rise-and-Fall racket and Spikes ow and Pin for Rise-and-Fall racket Use with Spikes 0T985/986 or 0T988/989 (see below) Diameter of rod: 8mm MTERIL: Pin Stainless steel; racket PVC-U 112 0T COLOURS: lack, Grey, White, rown uild-in Spikes MTERIL: Galvanised mild steel LENGTH - 0T T Drive-in Spikes MTERIL: Galvanised mild steel - 0T T Rafter rackets Top Rafter rackets ngle of bracket: 30 MTERIL: 0T745 PVC-coated steel 0T245 Galvanised mild steel 112 0T T COLOURS: 0T745 lack, Grey, rown Side Rafter rackets ngle of bracket: 30 MTERIL: 0T746 PVC-coated steel 0T246 Galvanised mild steel 112 0T T COLOURS: 0T746 lack, Grey, rown OSM RINWTER SYSTEMS Product, Design & Installation Guide Rafter rackets continued overleaf PVC-U RINWTER SYSTEM: RoundLine Gutter Gutter Union rackets 11

12 PVC-U RINWTER SYSTEM: RoundLine Half-round 112mm gutter system: rackets Connectors Outlets Rafter rackets continued djustable Top Rafter racket Use with Gutter Support racket 0T019 (page 10) ngle of bracket: 30 MTERIL: ZP-plated steel - 0T djustable Side Rafter racket Use with Gutter Support racket 0T019 (page 10) ngle of bracket: 30 MTERIL: ZP-plated steel - 0T Connectors to Metal and PVC-U Gutters Connector to 4" or 4 1 /2" Cast-Iron Half-Round Gutter Use with waterproof mastic, with EPDM seal 112 0T COLOURS: lack, Grey Connector to 4 1 /2" Cast-Iron Ogee Gutter Use with waterproof mastic, with EPDM seal 112 LH 0T RH 0T COLOURS: lack, Grey Connector to PVC-U True Half-Round Gutter, with EPDM seal 112 0T COLOUR: Grey Outlets and Stopends Running Outlet For gutter capacity, see page 6 Outlet for 68mm pipe, with EPDM seals 112 0T COLOURS: lack, Grey, White, rown 12 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

13 PVC-U RINWTER SYSTEM: RoundLine Half-round 112mm gutter system: Outlets Stopends ngles Connects to 68mm circular downpipe (page 15) Outlets and Stopends continued Swivelock Running Outlet, with Fitted 67 1 /2 Offset end Maximum fascia depth 138mm For gutter capacity, see page 6 Outlet for 68mm pipe, with EPDM seals 112 0T COLOURS: lack, Grey, White, rown Stopend Outlet For gutter capacity, see page 6 Outlet for 68mm pipe, with EPDM seal 112 0T COLOURS: lack, Grey, White, rown Internal Stopend 112 0T COLOURS: lack, Grey, White, rown External Stopend, with EPDM seal 112 0T COLOURS: lack, Grey, White, rown Gutter ngles 90 ngle, with EPDM seals 112 0T COLOURS: lack, Grey, White, rown 60 ngle, with EPDM seals 112 0T COLOURS: lack, Grey, White, rown Gutter ngles continued overleaf OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEM: RoundLine rackets Connectors Outlets Stopends ngles 13

14 PVC-U RINWTER SYSTEM: RoundLine Half-round 112mm gutter system: ngles Leaf Guard Spares Gutter ngles continued 45 ngle, with EPDM seals 112 0T COLOURS: lack, Grey, White, rown Multi-ngle, with EPDM seals NOMINL PRT NUMER 112 0T002 COLOURS: lack Fabricated ngles ngles fabricated to order For details, contact Technical Design Department, with EPDM seals NOMINL PRT NUMER COLOURS: lack, Grey, White, rown Leaf Guard Leaf Guard Plastic mesh designed to fit into 112mm gutter to prevent blocking by leaves and debris Pack contains 10 x 500mm lengths MTERIL: Recycled plastic 112 0T COLOURS: lack Spares Flexiclip NOMINL PRT NUMER 112 0T116 COLOURS: lack, Grey, White, rown Multi-ngle Flexiclip For use with multi-angle only NOMINL PRT NUMER 112 0T115 COLOURS: lack 14 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

15 PVC-U RINWTER SYSTEM: RoundLine 68mm circular downpipe system: Pipe rackets 68mm circular downpipe also connects to SuperLine (page 19), DeepLine (page 33) and StormLine (page44) Spares continued Gutter Seal MTERIL: EPDM NOMINL PRT NUMER 112 0T064 COLOUR: lack Pipe 68mm Circular Pipe NOMINL PRT LENGTH [m] NUMER 68 0T T T T COLOURS: lack, Grey, White, rown Except 0T082: Not available in White Pipe and Socket rackets Pipe racket For pipe support centres, see page 58 C 68 0T COLOURS: lack, Grey, White, rown Socket racket Use with Pipe Connector 0T024 (page 16), 67 1 /2 ranch 0T035 (page 18), Pipe Shoe 0T037 (page 17), 87 1 /2 end 0T161 (page 17), ccess Pipe 0T274 (page 18) For pipe support centres, see page 58 C 68 0T COLOURS: lack, Grey, White, rown Pipe or Socket racket For pipe support centres, see page 58 Use outside grooves for sockets 68 0T COLOURS: lack, Grey, White, rown Drive-in Pipe racket For pipe support centres, see page 58 MTERIL: Spike Galvanised steel; racket PVC-U 68 0T COLOURS: lack, Grey, rown OSM RINWTER SYSTEMS Product, Design & Installation Guide Pipe and Socket rackets and Spacer continued overleaf PVC-U RINWTER SYSTEM: RoundLine ngles Leaf Guard Spares 68mm Downpipe rackets 15

16 PVC-U RINWTER SYSTEM: RoundLine 68mm circular downpipe system: rackets Connectors daptors Pipe and Socket rackets continued racket Extension Piece Use with Pipe or Socket racket 0T033 (page 15) as a spacer dds a maximum of 45mm to the wall-to-pipe centre dimension Can be cut to suit 68 0T COLOURS: lack, Grey, White, rown Connectors and daptors Pipe Connector Support with Socket racket 0T038 (page 15) 68 0T COLOURS: lack, Grey, White, rown Connector to 2 1 /2 " Cast-Iron Rainwater Pipe Use with Pipe Connector 0T024 (see above) Support with Socket racket 0T038 (page 15) 68 0T COLOURS: lack, Grey Connector to 82mm PVC-U Drain Socket For external use only MTERIL: Polypropylene C - 3D COLOUR: Golden rown Rainwater daptor 68mm Pipe to 110mm PVC-U Drain For external use only For use with 110mm drain socket or spigot MTERIL: Polypropylene C D - 4D T COLOURS: 4D149 Golden rown 0T149 lack Universal Drain daptor For external use only For 110mm drain socket or spigot MTERIL: EPDM C D - 4D COLOUR: lack 16 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

17 PVC-U RINWTER SYSTEM: RoundLine 68mm circular downpipe system: end Offset ends Pipe Shoe 68mm circular downpipe also connects to SuperLine (page 19), DeepLine (page 33) and StormLine (page44) end 87 1 /2 end Use with Socket racket 0T038 (page 15) C 68 0T COLOURS: lack, Grey, White, rown Offset ends Offset end Socket 67 1 /2 offset. Minimum achievable offset: 90mm For use as top or bottom bend C 68 0T COLOURS: lack, Grey, White, rown Offset end Spigot 67 1 /2 offset. Spigot may be cut back by 20mm to achieve 70mm offset For use as top or bottom bend Use with Offset end 0T025 (see above), or Running Outlets 0T624/625 (pages 12 13) 68 0T COLOURS: lack, Grey, White, rown Long Tail Offset end Spigot 67 1 /2 offset Use with Straight Running Outlet 0T624 (page 12) 68 0T COLOURS: lack, Grey, White, rown Pipe Shoe Pipe Shoe Use with Socket racket 0T038 (page 15) C 68 0T COLOURS: lack, Grey, White, rown OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEM: RoundLine 68mm Downpipe: rackets Connectors ends Pipe Shoe 17

18 PVC-U RINWTER SYSTEM: RoundLine ccess Pipe Hopper Head Water utt Filler Rainwater Diverter ranch ranch 67 1 /2 Pipe ranch Use with Socket racket 0T038 (page 15) C 68 0T COLOURS: lack, Grey, White, rown ccess Pipe ccess Pipe with Screwed Door Use with Socket racket 0T038 (page 15) C 68 0T COLOURS: lack, Grey, White, rown Hopper Head Hopper Head Flow capacity 2.40 l/s Spigot sized for 68mm pipe WIDTH 68 0T COLOURS: lack, Grey, White, rown Waterbutt Filler Kit Waterbutt Filler Kit Provides an outlet to allow a waterbutt to be filled from a downpipe MTERIL: Polypropylene 68 0T COLOUR: lack Rainwater Diverter Kit Rainwater Diverter Kit Provides an outlet to allow a waterbutt to be filled from a downpipe ; Connector Polypropylene; Seal EPDM 68 0T COLOURS: lack, Grey, White, rown 18 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

19 PVC-U RINWTER SYSTEM: SuperLine Half-round 125mm gutter system: Gutter Gutter Union rackets Connects to 68mm downpipe (page 15) Gutter SuperLine Gutter NOMINL PRT LENGTH [m] NUMER 125 5T574 4 COLOURS: lack, rown Gutter Union Gutter Union Use with Gutter Support racket 5T519 (see below), or with Top/Side Rafter rackets (page 20), or with Rise-and-Fall rackets (page 20), with EPDM seals 125 5T COLOURS: lack, rown Support racket, Spacers and racer Gutter Support racket For support centres, see page T COLOURS: lack, rown Gutter racket Spacer Use with Gutter Support racket 5T519 (see above) to provide additional 21mm clearance - 0T COLOURS: lack, rown ngled racket Spacer 22 1 /2 angle Use with Gutter Support racket 5T519 (see above) when fascia board or rafter/truss ends are angled MTERIL: Polypropylene - 0T COLOURS: lack Support racket racer Converts Gutter Support racket 5T519 (see above) to threescrew fixing for areas with adverse weather conditions MTERIL: Polypropylene - 0T COLOUR: lack OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEMS: SuperLine Gutter Gutter Union rackets (lso RoundLine: Components) 19

20 PVC-U RINWTER SYSTEM: SuperLine Half-round 125mm gutter system: rackets Rise-and-Fall racket and Spikes ow and Pin for Rise-and-Fall racket Use with Spikes 0T985/986 or 0T988/989 (see below) Diameter of rod: 8mm MTERIL: Pin stainless steel; racket PVC-U 125 5T COLOURS: lack, rown uild-in Spike MTERIL: Galvanised mild steel LENGTH - 0T T Drive-in Spike MTERIL: Galvanised mild steel - 0T T Rafter rackets Top Rafter rackets ngle of bracket, 30 MTERIL: PVC-coated steel 125 5T COLOURS: lack, rown Side Rafter rackets ngle of bracket, 30 MTERIL: PVC-coated steel 125 5T COLOURS: lack, rown djustable Top Rafter racket Use with Gutter Support racket 5T519 (page 19) ngle of bracket: 30 MTERIL: ZP-plated steel - 0T CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

21 PVC-U RINWTER SYSTEM: SuperLine Half-round 125mm gutter system: rackets Outlets Stopends Gutter ngles Connects to 68mm circular downpipe (page 15) Rafter rackets continued djustable Side Rafter racket Use with Gutter Support racket 5T519 (page 19) ngle of bracket: 30 MTERIL: ZP-plated steel - 0T Outlet and Stopends Running Outlet For gutter capacity, see page 6 Outlet for 68mm pipe, with EPDM seals 125 5T COLOURS: lack, rown Internal Stopend 125 5T COLOURS: lack, rown External Stopend, with EPDM seal 125 5T COLOURS: lack, rown Gutter ngles 90 ngle, with EPDM seals 125 5T COLOURS: lack, rown 45 ngle, with EPDM seals 125 5T COLOURS: lack, rown Gutter ngles continued overleaf OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEM: SuperLine rackets Outlet Stopends Gutter ngles 21

22 PVC-U RINWTER SYSTEM: SuperLine Half-round 125mm gutter system: ngles Spares Gutter ngles continued Fabricated ngles ngles fabricated to order For details, contact Technical Design Department, with EPDM seals NOMINL PRT NUMER COLOURS: lack, rown Spares Gutter Seal MTERIL: EPDM NOMINL PRT NUMER 125 5T564 COLOUR: lack Flexiclip NOMINL PRT NUMER 125 5T516 COLOURS: lack, rown 22 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

23 PVC-U RINWTER SYSTEM: RoofLine Half-round 150mm gutter system: Gutter Gutter Union rackets Connects to 110mm circular downpipe (page 26) Gutter RoofLine Gutter NOMINL PRT LENGTH [m] NUMER 150 6T674 4 COLOURS: lack, Grey Gutter Union Gutter Union Use with Gutter Support racket 6T619 (see below), or with Top/Side Rafter rackets (page 24) and Rise-and-Fall rackets (see below), with EPDM seals 150 6T COLOURS: lack, Grey Gutter racket and Spacer Gutter Support racket For support centres, see page T COLOURS: lack, Grey Gutter racket Spacer Use with Gutter Support racket 6T619 (see above) to provide additional 21mm clearance - 0T COLOURS: lack, Grey Rise-and-Fall racket and Spikes ow and Pin for Rise-and-Fall racket Use with Spikes 0T985/986 (see below) or 0T988/989 (page 24) Diameter of rod: 8mm MTERIL: Pin stainless steel; racket PVC-U 150 6T COLOURS: lack, Grey uild-in Spikes MTERIL: Galvanised mild steel LENGTH - 0T T Rise-and-Fall racket and Spikes continued overleaf OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEMS: RoofLine Gutter Gutter Union rackets (lso SuperLine: Components) 23

24 PVC-U RINWTER SYSTEM: RoofLine Half-round 150mm gutter system: rackets Outlet Rise-and-Fall racket and Spikes continued Drive-in Spikes MTERIL: Galvanised mild steel - 0T T Rafter rackets Top Rafter rackets ngle of bracket: 30 MTERIL: PVC-coated steel 150 6T COLOURS: lack, Grey Side Rafter rackets ngle of bracket: 30 MTERIL: PVC-coated steel 150 6T COLOURS: lack, Grey djustable Top Rafter rackets Use with Gutter Support racket 6T619 (page 23) ngle of bracket: 30 MTERIL: ZP-plated steel - 0T djustable Side Rafter rackets Use with Gutter Support racket 6T619 (page 23) ngle of bracket: 30 MTERIL: ZP-plated steel - 0T Outlet and Stopends Running Outlet For gutter capacity, see page 6 Outlet for 110mm pipe, with EPDM seals 150 6T COLOURS: lack, Grey 24 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

25 PVC-U RINWTER SYSTEM: RoofLine Half-round 150mm gutter system: Stopends ngle Spares Connects to 110mm circular downpipe (page 26) Outlet and Stopends continued Internal Stopend 150 6T COLOURS: lack, Grey External Stopend, with EPDM seal 150 6T COLOURS: lack, Grey Gutter ngles 90 ngle, with EPDM seals 150 6T COLOURS: lack, Grey Fabricated ngles ngles fabricated to order For details, contact Technical Design Department, with EPDM seals NOMINL PRT NUMER COLOURS: lack, Grey Spares Gutter Seal MTERIL: EPDM NOMINL PRT NUMER 150 6T664 COLOUR: lack Flexiclip NOMINL PRT NUMER 150 6T616 COLOURS: lack, Grey OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 PVC-U RINWTER SYSTEM: RoofLine rackets Outlet Stopends ngles Spares 25

26 PVC-U RINWTER SYSTEM: RoofLine 110mm circular downpipe system: Pipe rackets Sockets Pipe 110mm Circular Pipe NOMINL PRT LENGTH [m] NUMER 110 4S S074 4 COLOURS: lack, Grey Pipe and Socket rackets Pipe racket For pipe support centres, see page 58 C 110 4S COLOURS: lack, Grey Socket racket Position in the recessed area adjacent to the sealing-ring housing For pipe support centres, see page 58 C 110 4S COLOURS: lack, Grey Pipe or Socket racket Multi-functional bracket that will support pipes or sockets When used as a socket bracket, position in the recessed area adjacent to the sealing-ring housing For pipe support centres, see page 58 MTERIL: ZP-Plated steel C 110 4S Sockets S/SW Single Socket For creating a fixed ring-seal joint on plain-ended pipe or fittings Has one ring-seal socket and one solvent-weld socket 110 4S COLOURS: lack, Grey D/SW Double Socket Has a solvent-weld socket at each end 110 4S COLOURS: lack, Grey 26 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

27 PVC-U RINWTER SYSTEM: RoofLine 110mm circular downpipe system: Sockets Connectors Reducer Connects to RoofLine (page 23) and 110mm Roof outlets (page 48) Sockets continued D/S Double Socket slip coupler for repair work Has ring-seal sockets 110 4S COLOURS: lack, Grey Connectors and Reducer S/S Connector to Cast-Iron or Clay Drain Socket Connects 110mm pipe to S 1211 or S 437 cast-iron socket, or S 65 clay drain socket Has one special end and one ring-seal socket C 110 4S COLOUR: Grey P/E Connector to Cast-Iron Spigot Plain-ended connector Connects 110mm pipe to cast-iron pipe with outside diameter mm Heat-shrink Connector to S 416 to Cast-Iron Spigot Use with Gasket 4S119 (see below) (MX) (MIN) 110 4S COLOURS: lack, Grey Gasket For use with Connector 4S134 (see above) MTERIL: Neoprene synthetic rubber NOMINL PRT NUMER 110 4S119 COLOUR: lack S/S Reducer Enables 110mm plain-ended pipe to be connected to a 160mm socket Has one plain end and one ring-seal or push-fit socket 160 x 110 6S COLOUR: Grey OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEM: RoofLine Pipe rackets Sockets Connectors Reducer 27

28 PVC-U RINWTER SYSTEM: RoofLine 110mm circular downpipe system: Offset ends Pipe Shoe ranches Offset ends SW/S Offset end 67 1 /2 offset Has one solvent-weld socket and one plain end C 110 4S COLOURS: lack, Grey S/SW Offset end 67 1 /2 offset Has one ring-seal socket and one solvent-weld socket C 110 4S COLOURS: lack, Grey S/S Offset end 67 1 /2 offset Has one plain end and one ring-seal socket C 110 4S COLOURS: lack, Grey D/S Offset end 67 1 /2 offset Has a ring-seal socket at each end C 110 4S COLOURS: lack, Grey Pipe Shoe S/S Pipe Shoe Use with Socket racket 4S083 (page 26) Has one plain end and one ring-seal socket 110 4S COLOURS: lack, Grey ranches S/S Single ranch 67 1 /2 Has one plain end and two ring-seal sockets C 110 4S COLOURS: lack, Grey 28 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

29 PVC-U RINWTER SYSTEM: RoofLine 110mm circular downpipe system: ranches Hopper Head Connects to RoofLine (page 23) and 110mm Roof outlets (page 48) ranches continued S/S Single ranch 87 1 /2 Has one plain end and two ring-seal sockets C 110 4S COLOURS: lack, Grey Hopper Head Hopper Head Flow capacity 6.47 l/s Spigot sized for 110mm socket WIDTH 110 4S COLOURS: lack, Grey OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEM: RoofLine Offset ends Pipe Shoe ranches Hopper Head 29

30 PVC-U RINWTER SYSTEM: Mini-Fit Half-round 75mm gutter system for small roof areas: Components Gutter Mini-Fit Gutter NOMINL PRT LENGTH [m] NUMER 75 3T T374 4 COLOURS: Grey, rown Gutter Jointing racket Gutter Jointing racket Used to join running lengths of gutter and fixing to fascia, with EPDM seals 75 3T COLOURS: Grey, rown Support racket Gutter Support racket For support centres, see page T COLOURS: Grey, rown Outlets and Stopend Running Outlet For gutter capacity, see page 6 Outlet sized for 55mm pipe, with EPDM seals 75 3T COLOURS: Grey, rown Stopend Outlet For gutter capacity, see page 6 Outlet sized for 68mm pipe, with EPDM seal 75 3T COLOURS: Grey, rown External Stopend, with EPDM seal 75 3T COLOURS: Grey, rown 30 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

31 PVC-U RINWTER SYSTEM: Mini-Fit Half-round 75mm gutter system for small roof areas: Components Connects to 55mm circular downpipe Gutter ngles 90 ngle, with EPDM seals 75 3T COLOURS: Grey, rown 45 ngle, with EPDM seals 75 3T COLOURS: Grey, rown Spares Gutter Pad Narrow MTERIL: EPDM NOMINL PRT NUMER 100 3T360 COLOUR: lack Pipe 55mm Circular Pipe NOMINL PRT LENGTH [m] NUMER 55 2T T T284 4 COLOURS: Grey, rown Pipe rackets C Saddle racket For pipe support centres, see page 58 C 55 2T COLOURS: Grey, rown C Pipe racket For pipe support centres, see page 58 C 55 2T COLOURS: Grey, rown Connector Pipe Connector 55 2T COLOURS: Grey, rown OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEM: Mini-Fit Gutter Components 31

32 PVC-U RINWTER SYSTEM: Mini-Fit 55mm circular downpipe system: Pipe rackets Connector ends ends 87 1 /2 end 55 2T COLOURS: Grey, rown C 45 end C 55 2T COLOURS: Grey, rown Offset end or Pipe Shoe Offset end or Pipe Shoe C 55 2T COLOURS: Grey, rown Hopper Head Hopper Head Flow capacity 2.4 l/s Spigot sized for 68mm pipe Use daptor 2T102 (see below) for 55mm pipe WIDTH 68 0T COLOURS: Grey, rown Hopper Head daptor Enables Hopper Head 0T332 (see above) to be used with 55mm pipe (page 31) 68x55 2T COLOURS: Grey, rown alloon Grating alloon Grating Fits into 55mm pipe 55 2T COLOURS: Grey, rown 32 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

33 PVC-U RINWTER SYSTEM: DeepLine Semi-elliptical 113mm gutter system: Gutter Gutter Union rackets Connects to 68mm circular downpipe (page 15) Gutter DeepLine Gutter NOMINL PRT LENGTH [m] NUMER 113 9T974 4 COLOURS: lack, Grey, White, rown Gutter Union Gutter Union Use with Support racket 9T919 (see below) and Rise-and-Fall racket 9T994 (page 34), with EPDM seals 113 9T COLOURS: lack, Grey, White, rown Support racket and Spacers Gutter Support racket For support centres, see page T COLOURS: lack, Grey, White, rown Gutter racket Spacer Use with Support racket 9T919 (see above) to provide additional 21mm clearance - 0T COLOURS: lack, Grey, White, rown ngled racket Spacer 22 1 /2 angle Use with Support racket 9T919 (see above) when fascia board or rafter/truss ends are angled MTERIL: Polypropylene - 0T COLOUR: lack OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEM: DeepLine Gutter Gutter Union rackets (lso Mini-Fit Components) 33

34 PVC-U RINWTER SYSTEM: DeepLine Semi-elliptical 113mm gutter system: rackets Outlet Stopends Rise-and-Fall racket and Spikes ow and Pin for Rise-and-Fall racket Use with Spikes 0T985/986 or 0T988/989 (see below) Diameter of rod: 8mm MTERIL: Pin Stainless steel; racket PVC-U 113 9T COLOURS: lack, Grey, White, rown uild-in Spikes MTERIL: Galvanised mild steel LENGTH - 0T T Drive-in Spikes MTERIL: Galvanised mild steel - 0T T Rafter rackets djustable Top Rafter racket Use with Gutter Support racket 9T919 (page 33) ngle of bracket: 30 MTERIL: ZP-Coated steel - 0T djustable Side Rafter racket Use with Gutter Support racket 9T919 (page 33) ngle of bracket: 30 MTERIL: ZP-Coated steel - 0T Outlet and Stopends Running Outlet For gutter capacity, see page 6 Outlet for 68mm pipe, with EPDM seals 113 9T COLOURS: lack, Grey, White, rown Internal Stopend 113 9T COLOURS: lack, Grey, White, rown 34 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

35 PVC-U RINWTER SYSTEM: DeepLine Semi-elliptical 113mm gutter system: Outlet Stopends ngles Spares Connects to 68mm circular downpipe (page 15) Outlet and Stopends continued External Stopend, with EPDM seal 113 9T COLOURS: lack, Grey, White, rown Gutter ngles 90 ngle, with EPDM seals 113 9T COLOURS: lack, Grey, White, rown 45 ngle, with EPDM seals 113 9T COLOURS: lack, Grey, White, rown Fabricated ngles ngles fabricated to order For details, contact Technical Design Department, with EPDM seals NOMINL PRT NUMER COLOURS: lack, Grey, White, rown Spares Gutter Seal MTERIL: EPDM NOMINL PRT NUMER 113 9T964 COLOUR: lack Flexiclip NOMINL PRT NUMER 113 9T916 COLOURS: lack, Grey, White, rown OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEM: DeepLine rackets Outlet Stopends ngles Spares 35

36 PVC-U RINWTER SYSTEM: SquareLine 100mm square gutter system: Gutter Gutter Union rackets Spacers Gutter SquareLine Gutter NOMINL PRT LENGTH [m] NUMER 100 4T T874 4 Gutter Union and Jointing racket Gutter Union Use with Gutter Support racket 4T819 (see below) or with djustable Top/Side Rafter rackets (page 37) Rise-and-Fall rackets (page 37), with EPDM seals 100 4T Gutter Jointing racket Used to join running lengths of gutter and fixing to fascia, with EPDM seals 100 4T Support racket and Spacers Gutter Support racket 3 Screw Fixing For support centres, see page T Gutter racket Spacer Use with Support racket 4T819 (see above) to provide additional 21mm clearance - 0T ngled racket Spacer 22 1 /2 angle Use with Support racket 4T819 (see above) when fascia board or rafter/truss ends are angled MTERIL: Polypropylene - 0T COLOURS: lack 36 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

37 PVC-U RINWTER SYSTEM: SquareLine 100mm square gutter system: rackets Connectors Connects to 61mm square downpipe (page 40) or via adaptor to 68mm circular downpipe (page 15) Rise-and-Fall racket and Spikes ow and Pin for Rise-and-Fall racket Use with Spikes 0T985/986 or 0T988/989 (see below) Diameter of rod: 8mm MTERIL: Pin Stainless steel; racket PVC-U 100 4T uild-in Spikes MTERIL: Galvanised mild steel LENGTH - 0T T Drive-in Spikes MTERIL: Galvanised mild steel - 0T T Rafter rackets djustable Top Rafter racket Use with Gutter Support racket 4T819 (page 36) ngle of bracket: 30 MTERIL: ZP-Plated steel - 0T djustable Side Rafter racket Use with Gutter Support racket 4T819 (page 36) ngle of bracket: 30 MTERIL: ZP-Plated steel - 0T Connectors to Other Gutters Connector to 4", 4 1 /2", or 5" Cast-Iron Ogee Gutter Use with waterproof mastic, with EPDM seals 100 LH 4T RH 4T COLOUR: lack OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEMS: SquareLine Gutter Gutter Union rackets Connectors 37

38 PVC-U RINWTER SYSTEM: SquareLine 100mm square gutter system: Connectors Outlets Stopends Connectors to Other Gutters continued Connector to 4 1 /2" RoundLine Gutter, with EPDM seal 100 4T COLOURS: lack, White Outlets and Stopends Running Outlet For gutter capacity, see page 6 Outlet for 61mm square pipe Can be adapted for use with 68mm circular pipe, with EPDM seals 100 4T Stopend Outlet For gutter capacity, see page 6 Outlet for 61mm square pipe Can be adapted for use with 68mm circular pipe Use with Support racket 4T819 (page 45), with EPDM seals 100 4T Internal Stopend 100 4T External Stopend, with EPDM seals 100 4T CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

39 PVC-U RINWTER SYSTEM: SquareLine 100mm square gutter system: Gutter ngles Spares Connects to 61mm square downpipe (page 40) or via adaptor to 68mm circular downpipe (page 15) Gutter ngles 90 ngle, with EPDM seals 100 4T ngle, with EPDM seals 100 4T Fabricated ngles ngles fabricated to order For details, contact Technical Design Department, with EPDM seals NOMINL PRT NUMER Spares Gutter Seal MTERIL: EPDM NOMINL PRT NUMER 100 4T864 COLOUR: lack Flexiclip NOMINL PRT NUMER 100 4T816 OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEM: SquareLine Connectors Outlets Stopends ngles Spares 39

40 PVC-U RINWTER SYSTEM: SquareLine 61mm square downpipe system: Pipe rackets Connectors daptors Pipe 61mm Square Pipe NOMINL PRT LENGTH [m] NUMER 61 4T T T T Pipe rackets and Spacer Pipe racket For pipe support centres, see page 58 C 61 4T Stand-off Pipe racket For pipe support centres, see page 58 C 61 4T Pipe racket Spacer Use as a spacer with Pipe Connector and racket 4T823 (see below) Pipe Shoe and racket 4T832 (page 42), Pipe racket 4T834 (see above), ccess Pipe 4T855 (page 43), and Wall Offset Pipe with ccess 4T858 (page 42) dds a maximum of 39mm to the wall-to-pipe centre dimension Can be cut to suit - 4T Connectors and daptors Pipe Connector and racket 61 4T Stand-off Pipe Connector and racket 61 4T CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

41 PVC-U RINWTER SYSTEM: SquareLine 61mm square downpipe system: Connectors daptors end 61mm square downpipe also connects to StormLine (page 44) Connectors and daptors continued Connector to 82mm PVC-U Drain Socket Use with Square-to-Round Drain daptor 4T836 (see below) For use with 82mm Drain Socket only For external use only MTERIL: Polypropylene C - 3D COLOUR: Golden rown Rainwater daptor 68mm Pipe to 110mm PVC-U Drain Use with Square-to-Round Drain daptor 4T836 (see below) For use with 110mm drain socket or spigot only For external use only MTERIL: Polypropylene C D - 4D T COLOURS: 4D149 Golden rown 0T149 lack Universal Drain daptor For use with 110mm drain socket or spigot ccepts SquareLine downpipe without an adaptor For external use only MTERIL: EPDM C D - 4D COLOUR: lack Drain daptor Square-to-Round llows 61mm square pipe to be connected to 68mm (round) Rainwater daptor 4D149, 0T149 or Connector 3D209 (see above) 61 4T Outlet daptor Square-to-Round llows outlets to be connected to 68mm circular pipe 61 4T end 87 1 /2 end C 61 4T OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEM: SquareLine Pipe rackets Connectors daptors end 41

42 PVC-U RINWTER SYSTEM: SquareLine 61mm square downpipe system: Offset ends Pipe Shoe ranch Offset ends Offset end Socket 67 1 /2 offset For use as top or bottom bend C 61 4T Offset end Spigot 67 1 /2 offset Minimum achievable offset 73mm For use as top or bottom bend 61 4T Wall Offset Pipe Provides 48mm offset to enable connection to drain outlet 61 4T Wall Offset Pipe with ccess Provides 48mm offset to enable connection to drain outlet Fitted with screwed, square access cover C 61 4T Pipe Shoe Pipe Shoe and racket C 61 4T ranch 67 1 /2 Pipe ranch C 61 4T CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

43 PVC-U RINWTER SYSTEM: SquareLine 61mm square downpipe system: ccess Pipes Components 61mm square downpipe also connects to StormLine (page 44) ccess Pipe ccess Pipe Fitted with screw-fixed, square access cover 61 4T Hopper Head Hopper Head Flow capacity 2.40 l/s Spigot sized for 61mm square pipe WIDTH 61 4T Rainwater Diverter Kit Rainwater Diverter Kit Provides an outlet to allow a waterbutt to be filled from a downpipe ; Connector Polypropylene; Seal EPDM 68 0T OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEM: SquareLine ends Pipe Shoe ranch ccess pipe Components 43

44 PVC-U RINWTER SYSTEM: StormLine Ogee profiled 111mm Gutter System: Gutter Union rackets Gutter StormLine Gutter NOMINL PRT LENGTH [m] NUMER 111 x 76 x 97 8T874 4 Gutter Union Gutter Union Used with Gutter Support rackets (8T819) (see below) or with Rise and Fall rackets (see page 45) (8T894), with EPDM seals 111 x 76 x 97 8T Support rackets and Spacer Gutter Support racket For support centres, see page x 76 x 97 8T Gutter Hanging racket For unobtrusive fixing, almost invisible from ground level For support centres, see page x 76 x 97 8T Gutter racket Spacer Use with Gutter rackets 8T819 or 8T849 (see above) to provide additional 21mm clearance - 0T CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

45 PVC-U RINWTER SYSTEM: StormLine Ogee profiled 111mm Gutter System: rackets Connects to 61mm square downpipe (page 40) or 68mm circular downpipe (page 15) Rise-and-Fall racket and Spikes ow and Pin for Rise-and-Fall racket Use with Spikes 0T985/986 or 0T988/989 (see below) Diameter of rod: 8mm MTERIL: Pin Stainless steel; racket PVC-U 110 8T uild-in Spikes MTERIL: Galvanised mild steel LENGTH - 0T T Drive-in Spikes MTERIL: Galvanised mild steel - 0T T Rafter rackets djustable Top Rafter racket Use with Gutter Support racket 8T819 (page 44) ngle of bracket: 30 MTERIL: ZP-Plated steel - 0T djustable Side Rafter racket Use with Gutter Support racket 8T819 (page 44) ngle of bracket: 30 MTERIL: ZP-Plated steel - 0T OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEMS: StormLine Gutter Gutter Union rackets 45

46 PVC-U RINWTER SYSTEM: StormLine Ogee profiled 111mm Gutter System: Outlets Stopends ngles Outlets and Stopends Running Outlet For gutter capacity, see page 6 Can be used with 68mm circular pipe and 61mm Square Pipe, with EPDM seals 111 x 76 x 97 8T Stopend Outlet For gutter capacity, see page 6 C D, with EPDM seal C D 111 x 76 x 97 LH 8T x 76 x 97 RH 8T Internal Stopend 111 x 76 x 97 LH 8T x 76 x 97 RH 8T External Stopend, with EPDM seal 111 x 76 x 97 LH 8T x 76 x 97 RH 8T Gutter ngles Internal 90 ngle, with EPDM seals 111 x 76 x 97 8T External 90 ngle, with EPDM seals 111 x 76 x 97 8T CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

47 PVC-U RINWTER SYSTEM: StormLine Ogee profiled 111mm Gutter System: ngles Spares Connects to 61mm square downpipe (page 40) or 68mm circular downpipe (page 15) Gutter ngles continued Internal 45 ngle, with EPDM seals 111 x 76 x 97 8T External 45 ngle, with EPDM seals 111 x 76 x 97 8T Fabricated ngles ngles fabricated to order For details, contact Technical Design Department, with EPDM seals NOMINL PRT NUMER 111 x 76 x 97 - Spares Gutter Seal MTERIL: EPDM NOMINL PRT NUMER 111 x 76 8T864 COLOUR: lack Flexiclip C NOMINL PRT NUMER 111 x 76 x 97 8T816 Rainwater Diverter Kit Rainwater Diverter Kit Provides an outlet to allow a waterbutt to be filled from a downpipe ; Connector Polypropylene; Seal EPDM 61/68 0T OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEM: Stormline Outlets Stopends ngles Spares 47

48 PVC-U RINWTER SYSTEM: Roof Outlets 82mm and 110mm roof outlet and circular pipe systems: Pipe rackets Roof Outlet C SW/S Domed Roof Outlet Outlet capacity (outlet at centre of roof): 82mm outlet 2.97 l/s; 143m 2 max. roof area 110mm outlet 4.35 l/s; 209m 2 max. roof area Fitted with: 82mm outlet solvent-weld socket 110mm outlet solvent-weld socket C 82 3S S COLOUR: Grey Pipe 82mm and 110mm Circular Pipe NOMINL PRT LENGTH [m] NUMER 82 3S S COLOURS: 3S074 lack, Grey 4S074 lack, Grey, Olive, White, rown Pipe and Socket rackets Pipe racket For pipe support centres, see page 58 C 82 3S S COLOURS: 3S082 lack, Grey 4S082 lack, Grey, Olive, White, rown Socket racket 82mm Pipe For pipe support centres, see page 58 C 82 3S COLOURS: lack, Grey Socket racket 110mm Pipe For pipe support centres, see page 58 C 110 4S COLOURS: lack, Grey, Olive, White, rown 48 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

49 PVC-U RINWTER SYSTEM: Roof Outlets 82mm and 110mm circular pipe systems: Sockets Connectors Pipe and Socket rackets continued C Pipe or Socket racket Multi-functional bracket that can be used to support pipes or sockets When using as a socket bracket, position in the recessed area adjacent to the sealing-ring housing For pipe support centres, see page 58 MTERIL: ZP-Coated steel C 82 3S S Sockets D/S Double Socket Provides a slip coupler for repair applications Has a ring-seal socket at each end 82 3S S COLOURS: 3S105: lack, Grey 4S105: lack, Grey, rown D/SW Double Socket Has a solvent-weld socket at each end 110 4S COLOURS: lack, Grey, rown S/SW Single Socket Creates a fixed ring-seal joint on plain-ended pipe or fittings Has one ring-seal socket and one solvent-weld socket 82 3S S COLOURS: 3S124 lack, Grey 4S124 lack, Grey, Olive, White, rown Connectors P/E Connector to Cast-Iron Spigot Plain-ended connector Connects OSM 82mm/110mm circular pipe to cast-iron pipe with outside diameter mm/ mm Heat-shrink Connector to S 416 to Cast-Iron Spigot Use with two Seals 3S130 (page 53) /Gasket 4S119 (page 65) OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 (MX) (MIN) 82 3S S COLOUR: 3S134 Grey 4S134 lack, Grey, rown Connectors continued overleaf PVC-U RINWTER SYSTEM: Roof Outlets Roof Outlet Pipe Components 49

50 PVC-U RINWTER SYSTEM: Roof Outlets 82mm and 110mm circular pipe systems: Pipe Components Connectors continued S/S Connector to Cast-Iron or Clay Drain Socket Connects RoofLine pipe to S 1211 or S 437 cast-iron socket, or S 65 clay drain socket Has one plain end and one ring-seal or push-fit socket C 110 4S COLOUR: Grey Reducer S/S Reducer Enables an 82mm pipe to be connected to a 110mm socket Has one plain end and one ring-seal socket 110 x 82 4S COLOURS: lack, Grey Offset ends SW/S Offset end 67 1 /2 offset Has one solvent-weld socket and one plain end C 82 3S S COLOURS: 3S435 Grey 4S435 lack, Grey, White, rown S/SW Offset end 67 1 /2 offset Has one ring-seal socket and one solvent-weld socket C 82 3S S COLOURS: 3S440: lack, Grey 4S440: lack, Grey, White, rown S/S Offset end 67 1 /2 offset Has one plain end and one ring-seal socket C 82 3S S COLOURS: 3S444 lack, Grey 4S444 lack, Grey, White, rown 50 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

51 PVC-U RINWTER SYSTEM: Roof Outlets 82mm and 110mm circular pipe systems: Pipe Components ranches and Pipe Shoe S/S Single ranch 67 1 /2 Has one plain end and two ring-seal sockets C 82 3S S COLOURS: 3S200 Grey 4S200 lack, Grey, rown S/S Single ranch 87 1 /2 Has one plain end and two ring-seal sockets C 82 3S S COLOURS: 3S190 lack, Grey 4S190 lack, Grey, White, rown Pipe Shoe S/S Pipe Shoe Use with Socket racket 3S083/4S083 (page 60) Has one plain end and one ring-seal or socket 82 3S S COLOURS: lack, Grey Hopper Head Hopper Head Flow capacity 3.78 l/s Spigot sized for 82mm pipe or socket WIDTH 82 3S COLOURS: lack, Grey OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEM: Roof Outlets Pipe Components 51

52 PVC-U RINWTER SYSTEMS: ncillaries and Spares Cleaner Degreasing Cleaner Number 1 Supplied in screw-top cans Use for cleaning solvent-weld joints prior to application of solvent weld PRT NUMER 125ML 4S ML 4S380 Solvent Cement Solvent Cement Number 2 Supplied in screw-top cans Use for making solvent-weld joints PRT NUMER 125ML 4S ML 4S ML 4S385 Solvent Cement Filler Use for solvent welding two surfaces where there is no interference fit Supplied in a tube PRT NUMER 200G 4S394 Lubricant Silicone Lubricant Supplied in tubes Use to aid assembly of ring-seal socket-and-spigot joints PRT NUMER 50G 4S391 Silicone Lubricant Spray Silicone Lubricant Spray Supplied in 400ml spray can Use to aid assembly of ring-seal socket-and-spigot joints 400ML PRT NUMER 4S392 Gutter Spares Gutter Seal MTERIL: EPDM NOMINL PRT NUMER 112 0T064 for RoundLine 125 5T564 for SuperLine 150 6T664 for RoofLine 113 9T964 for DeepLine 100 4T864 for SquareLine 111 x 76 8T864 for StormLine COLOUR: lack 52 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

53 PVC-U RINWTER SYSTEMS: ncillaries and Spares Gutter Spares continued Flexiclip NOMINL PRT NUMER 112 0T116 for RoundLine 125 5T516 for SuperLine 150 6T616 for RoofLine 113 9T916 for DeepLine 100 4T816 for SquareLine 111 x 97 8T816 for StormLine COLOURS: 0T016, 9T916 lack, Grey, White, rown 4T816, 8T816 lack, White, rown 5T516, lack, rown 6T616, lack, Grey Gutter Pad Narrow For old style gutter joints not flexiclip joints To glue in seals use waterproof contact adhesive MTERIL: EPDM NOMINL PRT NUMER 112 0T060 for RoundLine 150 6T660 for RoofLine 95 3T360 for Mini-Fit 100 4T860 for SquareLine COLOUR: lack Gutter Pad Wide For old style gutter joints not flexiclip joints To glue in seals use waterproof contact adhesive MTERIL: EPDM NOMINL PRT NUMER 112 0T061 for RoundLine 150 6T661 for RoofLine 100 4T861 for SquareLine COLOUR: lack Pipe Spares Ring Seal Spares MTERIL: EPDM NOMINL PRT NUMER 82 3S S130 Snap Cap Spare For a Ring-Seal socket PRT NUMER 82 3S S116 COLOURS: 3S116 lack, Grey 4S116 lack, Grey, White, rown OSM RINWTER SYSTEMS Product, Design & Installation Guide PVC-U RINWTER SYSTEMS: ncillaries Spares 53

54 DESIGN PROCEDURES Gutter Support Determining Gutter Flow Capacity The capacity of a rainwater system effectively to drain a roof area depends on four factors: z Gutter capacity z Level to which the gutter is laid z Number of outlets z Location of outlets To determine the correct combination, first calculate the area to be drained the Effective Roof rea. Calculating Effective Roof rea Pitched roof There are two methods of calculating Effective Roof rea, which allows for the effects of wind. PROCEDURE (see Fig.1) S EN 12056: Part 3: Measure in metres: Length from eaves to ridge Height of roof from eaves to ridge C Length of roof 2. Use the formula specified in S EN 12056: Part 3: 2000 Effective Roof rea (in m 2 ) = ( + ) x C 2 3. Check this figure against the capacity of OSM systems set out in Table 1. WORKED EXMPLE: (Procedure ) = 7.0m = 3.0m C = 12.0m x 12 ( 2) ( ) x x 12 = 102m 2 Effective Roof rea [ER] Conclusion: in this example, Table 1 shows that: If outlet positioned at END of run: StormLine and DeepLine are suitable if laid to a fall of 1:600 RoofLine is suitable laid level or to a fall If outlet positioned at CENTRE of run: ll systems (except Mini-Fit) are suitable if laid to a fall of 1:600 ll systems (except RoundLine and Mini-Fit) are suitable if laid level Fig. 1 Pitched roof PROCEDURE (see Fig.1) uilding Regulations Part H Measure roof plan area in square metres: Length (L) x Width (W) = rea (m 2 ) 2. To find Effective Roof rea, multiply roof plan area as follows, according to angle of pitch: if 30º pitch rea x 1.29 if 45º pitch rea x 1.5 if 60º pitch rea x 1.87 Wall abutting roof Walls above abutting roofs will drain on to the roof below. For a single wall the effective catchment area is taken to be half the area of the elevation. PROCEDURE (see Fig. 2) 1. Measures in metres: D Length of wall above roof E Height of wall above roof 2. Use the formula: Effective Wall rea (in m 2 ) = (D x E) 2 3. dd the Effective Wall rea (if appropriate) to the Effective Roof rea to be drained Fig. 2 Wall abutting roof E D C Table 1: Maximum Effective Roof rea (m 2 ) Running outlet at END of gutter Running outlet at CENTRE of gutter Stopend outlet at END of gutter System RoundLine SuperLine RoofLine Mini-Fit DeepLine SquareLine StormLine StormLine Gutter laid level Gutter laid at fall 1:600 Gutter laid level Gutter laid at fall 1: Gutter laid level Gutter laid at fall 1: NOTE: The roof areas capable of being drained are calculated in accordance with S EN 12056: Part 3: 2000, to which reference should be made before varying design considerations. 54 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

55 DESIGN PROCEDURES Gutter Jointing Connections to Other Gutter Types Determining Gutter Flow Capacity Factors to consider Gutter fall Gutters laid to a fall are more efficient than gutters laid level. fall of 1:600 (25mm in 15m) is recommended. The high capacity characteristics of OSM gutter systems mean that performance is not compromised by being laid level. However, laying the gutter to a fall will increase flow capacity and the area of roof that can be drained particularly if the downpipe is positioned centrally, Silting will also be prevented. Number of outlet(s) The more outlets along a gutter, and the shorter the distance rainwater has to travel, the more effective the system. EXMPLE: C Flow rates (litres/sec) Our changeable climate means it is impossible to rule out flooding and overflow. Generally, it is satisfactory to design to a rainfall intensity of 75mm per hour where overflow will not cause damage within the building. For valley and parapet gutters or where a building or its contents require additional measures of protection, a higher rainfall intensity should be used. See SEN :2000 Table 3 shows the maximum capacity for each system, gutter laid level or to a fall of 1:600. Established using the test method prescribed in EN :2000 To calculate flow For 75mm per hour rainfall intensity, calculate: Effective Roof rea (m 2 ) x = litres per second For other rainfall intensity levels, calculate as follows: Effective Roof rea (m 2 ) x rainfall intensity (mm per hour) 3600 = litres per second Flat roofs For roofs with a pitch less than 10º: the Effective Roof rea for the purposes of flow calculation is simply the plan area of the roof. For drainage via gutters positioned at roof perimeter: Refer to Table 3 below to determine whether system capacity is sufficient for area to be drained. For drainage via OSM flat roof outlets: Refer to Table 2 below. Roof Outlets positioned in the centre of a flat roof can drain larger areas than outlets located at the edge or corner of the roof. It is good practice to have a minimum of 2 flat Roof Outlets per roof if no overflow point has been designed. S EN 12056: Part 3: For reference to Standards see page 77. Layout is more efficient than, and C is more efficient than. Location of outlet(s) Outlets located near gutter angles also reduce system efficiency. EXMPLE: Where a gutter length contains 1 or more gutter angles (greater than 10º) then multiply the Maximum Effective Roof reas in Table 1 by a reduction factor of Outlet 3S414 4S414 Table 2: Roof Outlet Capacity Outlet Diameter Maximum roof area mm m 2 Litres per second Table 3: Gutter Flow Capacity (l/s) Running outlet at END of gutter Running outlet at CENTRE of gutter Stopend outlet at END of gutter System RoundLine SuperLine RoofLine Mini-Fit DeepLine SquareLine StormLine StormLine Gutter laid level Gutter laid at fall 1:600 Gutter laid level Gutter laid at fall 1: Gutter laid level Gutter laid at fall 1: OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 DESIGN Gutter Design Procedures 55

56 DESIGN PROCEDURES Gutter Support Gutter Support Gutter location S EN : 2000, section & NE.2.1 states Gutters designed as level or nominally level should be laid to a nominal gradient of between 1mm/m and 3mm/m where practicable. The gradient of an eaves gutter shall not be so steep that the gutter drops below the level of the roof to such an extent that water discharging from the roof will pass over the front edge of the gutter. lso, the gutter should be fixed centrally under the roof edge and close beneath it. System RoundLine SuperLine RoofLine Mini-Fit DeepLine SquareLine StormLine Table 4: lternative racketing rrangements Gutter Support racket Single Screw Fixing Multi-Screw Fixing Gutter Hanging racket Rise-and-Fall ow and Pin racket 0T019 0T039 0T914 5T519 5T T119 5T594 6T619 6T619 _ 6T694 3T319 _ 9T919 9T919 _ 9T994 4T819 4T819 4T894 8T819 8T849 8T894 Support options (see Fig. 3) Fig. 3 General arrangement RoundLine Support can be provided by EITHER Gutter fittings that incorporate screwfixing positions (e.g. Running Outlet) 0T010 0T625 0T005 OR 0T019 Gutter Support rackets, Hanging rackets or Rise-and-Fall racket assemblies, according to the system. 0T025 0T003 See Table 4 for bracketing arrangements available for each system. 0T024 Gutter support centres The gutter should be supported as follows: 0T033 t maximum centres of 1m Within 150mm of both sides of any angle t the centre of gutter joints (see also Gutter Jointing page 57) 0T037 0T mm maximum between ngle and Support racket Multi-screw fixings Use of multi-screw fixings is particularly recommended on high buildings and in areas exposed to strong winds. Rafter rackets Where it is not possible to screw-fix direct to fascia, ngled, djustable, Top and Side Rafter rackets, and Drive-in or uild-in Spikes are available. ngled fascias For support of gutters to be fixed to angled fascia, an ngled racket Spacer 0T045 is available. This is suitable for RoundLine, SuperLine, SquareLine, StormLine and DeepLine systems. 56 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

57 DESIGN PROCEDURES Gutter Jointing Connections to Other Gutter Types Gutter Jointing Gutter jointing OSM Rainwater systems are fitted with a Flexiclip (excluding Mini-Fit) and seal jointing mechanism, making it easy to connect gutter to fittings. (See Fig. 4) ecause the clip is flexed, rather than the whole component, this ensures a positive, permanently watertight joint. Fig. 4 Flexiclip gutter joint Thermal movement Gutter joint fittings are marked to indicate the limit for positioning gutter ends to allow for thermal expansion. These marked positions must be fully observed during assembly and installation. (See Fig. 5) Fig. 5 llowance for thermal movement Expansion gap Gutter Gutter gutter jointing bracket or gutter union with bracket should be fitted within 300mm from the end of terminal lengths of gutter. Curved eaves For a gutter to fit into a curved eaves detail, it is necessary to use a number of shallow angles. Shallow angles can be fabricated to order. Contact Wavin Technical Design Department, stating the radius and circumference of the eaves. Wavin will calculate the optimum number and angle of gutter fittings required. Leaves In areas where trees are close to a roof, care should be taken to ensure that gutters and pipes do not become clogged with wet leaves. The OSM RoundLine system includes Leaf Guard 0T017, which provides a simple-to-fit method to keep gutters and pipes clear of fallen leaves. Required lengths can be easily cut and simply fit inside the gutter. Leaf Guard can be used with RoundLine and DeepLine systems only. Connections to Other Gutter Types OSM RoundLine and SquareLine systems have a range of special connectors to enable joints between gutter types to be produced, (see Table 5). These are particularly useful in refurbishment work, where it may be necessary to replace sections of old gutter but also connect to the existing gutter on adjoining buildings. (See Fig. 6/7) CI = Cast Iron Fig. 6 RoundLine connection to cast iron gutter Fig. 7 SquareLine connection to cast iron gutter RoundLine Gutter 150mm 0T mm 4T815 Cast iron gutter Cast iron gutter 0T019 4T819 SquareLine Gutter OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 DESIGN Gutter Design Procedures 57

58 DESIGN PROCEDURES Pipe Support Connections of Gutter Outlets Pipe Support Pipe support centres The maximum support centres for pipes installed vertically and horizontally are shown in Table 6 below. Thermal movement gap of 10-12mm must be left between the top of each length of pipe and the fitting to which it is connected to allow for thermal movement. Offsets To give offsets maximum support, a Pipe racket should be fitted directly below the lower Offset end. Uneven surfaces For walls that have an uneven surface (for example, walls featuring 'tudorised' beams), a Pipe racket Spacer (0T030-68mm round pipe or 4T731 square pipe) may be used to enable pipe fixings to remain in line. (See Figs. 8/9) For very uneven surfaces such as random rubble stone walls, a special Drive-in Pipe racket 0T143 is available to use with 68mm circular pipe only. The galvanised steel spike can be driven into the mortar joints to allow the pipe to be installed without distorting. Fig. 8 pplication of Pipe racket Spacer 5T508 0T030 Table 6: Maximum Pipe Support Centres Maximum centres (m) Fig. 9 Use of Pipe racket Spacer 0T033 Pipe Size Vertical Horizontal 55mm 61mm 68mm 82mm 110mm T030 Typical Connections of Gutter Outlets to OSM Pipe Each OSM rainwater gutter system offers a number of alternatives for connection of pipe to gutter system, depending upon: - Depth of the fascia - Whether there is a soffit - What requirements the designer has of the system ll OSM systems include a Running Outlet. The following systems offer additional outlets: RoundLine: Swivelock Outlet 0T625 - (outlet fitted with integral offset bend) and Stopend Outlet 0T007. Mini-Fit: Stopend Outlet 3T307. SquareLine: Stopend Outlet 4T807. StormLine: Stopend Outlet 8T807 left hand; 8T808 right hand. System 55mm 68mm 110mm 61mm RoundLine SuperLine RoofLine Mini-Fit DeepLine SquareLine StormLine Table 7: Outlet Connection Components Circular pipe Square pipe - 0T624 or - - 0T625 or 0T007-5T T606-3T306 or T307-9T T806 or - 4T806 or 4T T807 4T837-8T806 or - 8T806 8T807 or 8T807 8T808 8T CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

59 DESIGN DETILING Connections of Gutter Outlets/Pipe & Offsets Typical Connections of Gutter Outlets continued Shallow offsets Components to achieve a shallow offset are listed in Table 8 below: Table 8: Shallow Offset Components Fig. 10 RoundLine shallow offset 0T625 System RoundLine SuperLine DeepLine Components required 0T T026 (90mm projection or 70mm projection by cutting back spigot of 0T026) OR 0T x 0T026 (90mm projection OR 70mm projection by cutting back spigot of 0T026) To be used with Pipe racket 0T034, fitted below lowest Offset end to 68mm circular pipe 5T x 0T026 (90mm projection OR 70mm projection by cutting back spigot of 0T026) To be used with Pipe racket 0T034, fitted below lowest Offset end to 68mm circular pipe 9T x 0T026 (90mm projection OR 70mm projection by cutting back spigot of 0T026) To be used with Pipe racket 0T034, fitted below lowest Offset end 0T026 0T034 RoofLine Mini-Fit SquareLine to 110mm circular pipe 6T x 4S444 (minimum projection 155mm) To be used with Socket racket 4S083, fitted to lowest Offset end to 55mm circular pipe 3T x 2T227 To be used with Saddle racket 2T081 fitted below lowest Offset end to 68mm circular pipe 4T806/7 + 4T x 0T026 (90mm projection or 70mm projection by cutting back spigot 0T026) To be used with Pipe racket 0T034, fitted below lowest Offset end Fig. 11 SquareLine shallow offset 4T806 to 61mm square pipe 4T806/7 + 4T T823 (minimum projection 48mm) OR 4T806/7 + 2 x 4T826 (73mm projection) To be used with Pipe rackets 4T833 or 4T834 fitted below lowest Offset end 4T838 4T823 StormLine to 68mm circular pipe 8T807/8 + 2 x 0T026 (90mm projection or 70mm projection by cutting back spigot of 0T026) OR 8T x 0T026 (90mm projection or 70mm projection by cutting back spigot of 0T026) To be used with Pipe racket 0T034, fitted below lowest Offset end to 61mm square pipe 8T806/7/8 + 4T T823 (minimum projection 48mm) OR 8T806/7/8 + 2 x 0T026 (90mm projection or 70mm projection by cutting back spigot of 4T826) To be used with Pipe rackets 4T833 or 4T834 fitted below lowest Offset end Fig. 12 8T806 4T838 4T823 Typical Connections of Gutter Outlets continued overleaf OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 DESIGN DETILING Outlet/Pipe Connections 59

60 DESIGN DETILING Connections of Gutter Outlets Typical Connections of Gutter Outlets continued Deep Offsets For components to achieve a deep offset, see Table 9 below Table 9: Deep Offset Components Fig. 13 RoundLine deep offset 0T624 System RoundLine SuperLine DeepLine RoofLine Mini-Fit SquareLine StormLine 0T T025 OR 0T x 0T025 OR 0T T T025 To be used with Pipe racket 0T034, fitted below lowest Offset end with offcut of pipe, length to suit to 68mm circular pipe 5T x 0T025 OR 5T T T025 To be used with Pipe racket 0T034, fitted below lowest Offset end with offcut of pipe, length to suit to 68mm circular pipe 9T x 0T027 OR 9T T T025 To be used with Pipe racket 0T034, fitted below lowest Offset end with offcut of pipe, length to suit to 110mm circular pipe 6T x 4S445 OR 6T x 4S440 To be used with Socket racket 4S083, fitted to lowest Offset end with offcut of pipe, length to suit Not applicable Components required to 68mm circular pipe 4T806/7 + 4T T T025 To be used with Pipe racket 0T034, fitted below lowest Offset end with offcut of pipe, length to suit to 61mm square pipe for downpipe close to wall 4T806/7 + 2 x 4T825 To be used with Pipe racket 4T834 fitted below lowest Offset end with offcut of pipe, length to suit to 61mm square pipe for downpipe off the wall 4T806/7 + 2 x 4T825 To be used with Pipe racket 4T833 fitted below lowest Offset end with offcut of pipe, length to suit to 68mm circular pipe 8T806/7/8 + 0T T025 To be used with Pipe racket 0T034, fitted below lowest Offset end with offcut of pipe, length to suit to 61mm square pipe for downpipe close to wall 8T806/7/8 + 2 x 4T825 To be used with Pipe racket 4T834 fitted below lowest Offset end with offcut of pipe, length to suit to 61mm square pipe for downpipe off the wall 8T806/7/8 + 2 x 4T825 To be used with Pipe racket 4T833 fitted below lowest Offset end with offcut of pipe, length to suit 0T025 0T034 Pipe off-cut to suit 0T025 Fig. 14 RoundLine deep offset and deep fascia Fig. 15 SquareLine deep offset - close to wall 4T825 0T025 0T034 0T624 Pipe off-cut to suit 4T806 0T027 Pipe off-cut to suit 4T CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

61 DESIGN DETILING Connections to Other Materials Connections to Other Materials Connections to existing iron pipe OSM Rainwater systems can be connected to the sound part of an existing circular cast iron system as follows: RoundLine, SuperLine, DeepLine, StormLine 68mm pipe can be inserted directly into an existing 2 1 /2" cast iron socket. Mastic or other sealing compounds are not needed (See Fig. 16). For connection to a 2 1 /2" cast iron spigot, use Connector OT092 with Pipe Connector OT024. To cast iron spigot Use Heat Shrink Connector 4S134, together with 1 x Seal 4S119, to connect 110mm circular downpipe to a S 1211 or S 437 cast iron spigot. (See Fig. 18) Fig. 18 To cast iron soil spigot (via 4S134 and 4S119) 110mm downpipe 4S134 daptor 4S119 Gasket Connections to existing clay socket OSM RoofLine 110mm PVC-U pipe can also be connected to a S 65 Clay Drain Socket using S/S Connector 4S107. (See Fig. 19) Fig. 19 To Clay Drain Socket (via 4S107) 68mm downpipe 4S107 Sand/cement Caulking material Fig. 16 Connection to existing iron pipe socket 68mm RoundLine Clay drain Mastic bead Cast iron pipe socket RoofLine To cast iron socket Use S/S Connector 4S107 to connect 110mm circular downpipe to S 1211 or S 437 Cast Iron Socket. (See Fig. 17) SquareLine, StormLine To 2 1 /2" round cast iron socket Use Outlet daptor - Square to Round 4T837 to convert 61mm square downpipe to a 68mm circular Cast Iron Socket. Insert pipe directly in to an existing Cast Iron Socket. Mastic or other sealing compounds are not needed. Fig. 17 Cast iron drain socket (via 4S107) 110mm downpipe 4S107 daptor Iron drain OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 DESIGN DETILING Outlet Connections Connections to Other Materials 61

62 DESIGN DETILING Connections to elow Ground Drainage Connections to elow Ground Drainage number of alternative arrangements are available for terminating rainwater downpipe at ground level: Discharge over an open gully, using a Pipe Shoe for the relevant downpipe system* Indirectly, via an OSM 110mm ottle Gully or Vertical Inlet Hopper Directly, via a Rainwater daptor or Universal Drain daptor NOTE: For full product details, see OSM elow Ground Drainage Systems: Product Guide Table 10 below sets out the component requirements for connection of downpipes to below ground drainage. Pipe Shoes For an open discharge*, a downpipe should be terminated with an open Pipe Shoe. The Pipe Shoe should be situated centrally over the gully and securely fixed to the wall with the appropriate bracket. (See Fig. 20) Fig. 20 Pipe Shoe over gully* (68mm circular pipe illustrated) 68mm downpipe 0T038 OSM Plain Hopper 0T037 Indirect connections Via 110mm OSM Vertical Inlet Hopper Terminate downpipe below the back plate. (See Fig. 21) Fig. 21 Connection to bottle gully (68mm circular pipe illustrated) 68mm downpipe OSM Vertical Inlet Hopper Via 110mm OSM ottle Gully Terminate downpipe below the grating. (See Fig. 22) Fig. 22 Connection to bottle gully 0T034 68mm RoundLine pipe OSM ottle Gully Table 10: Connections to elow Ground Drainage Circular Pipe Square Pipe Type 55mm 68mm 82mm 110mm 61mm Discharge over open gully* Pipe Shoe 2T T S S T832 Over Plain Hopper/ottle Gully 2T081 0T038 3S083 4S083 Indirect Connection: to 110mm drainage Via OSM ottle Gully 4D700 4D700 4D D161 4D700 4D900 4D900 3D161 Into Side 4D900 Via OSM Vertical Inlet Hopper 4D508 4D508 Into Side Socket 4D508 4D504 4D504 Socket 4D504 Direct Connection: to 110mm PVC-U drain 4T858/838 + Via Rainwater daptor - 0T149/4D149 - No daptor 4T836 + Required 0T149/4D149 Via Universal Drain daptor 4D159 4D T858/838 +4D159 Reducer - - 4S Direct Connection: to 82mm PVC-U drain Via Connector(s) 3S094 3D209 No daptor - 4T858/838 Required +4T836+3D209 *NOTE: Rainwater pipe which discharges into a gully must terminate ELOW the gully grating but OVE the water seal, preferably by using a back inlet. (S EN 12056: Part 3: ) 62 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

63 DESIGN DETILING Roof Outlets Materials Roof Outlets OSM Roof Outlets are two-piece Fig. 23 Roof Outlet installation components manufactured in PVC-U. They consist of a funnel-shaped body and a flange which is prominently ribbed to give good adhesion to asphalt and hot a) Mastic asphalt roof Two layers mastic asphalt Grating retained by captive non-corrosive bolt b) uilt-up roof uilt-up roof; timber, felt and chippings Grating retained by captive non-corrosive bolt bitumen. (See Fig. 23) The outlets have a solvent socket tail for connection to pipe or bends Rebated funnel mouth allows a strong, thick edge to mastic asphalt finishes to prevent lifting Screed Concrete 4S414 4S124 4S083 Third layer of felt retained by grating 4S414 4S161 Grating strong enough to withstand normal foot traffic uilt-in gravel guard to prevent ingress of roof chippings eads and grooves prevent puddling and ensure complete seepage of water Grate is secured to outlet body with a non-corrosive bolt (supplied) Materials: Properties and Performance Chemical resistance OSM Rainwater systems components are manufactured from PVC-U or Polypropylene. They are totally unaffected by even the most heavily polluted atmosphere, or by impurities in the rainwater. The components are self-coloured. They may, however, be painted with normal household paints if an alternative colour is required. Oil-based gloss paint is the most suitable for this purpose. For best results, slightly abrade the surface with sandpaper and clean thoroughly before painting. Physical attack OSM Rainwater systems are not susceptible to insect or vermin attack. Unlike cast iron systems, plastic has no scrap value and is therefore less likely to be targeted by vandals or thieves. Ultra violet light OSM Rainwater systems gutter, pipe and fittings are resistant to the effects of ultra violet light. lthough the colour may fade slightly after a number of years exposure to strong sunlight, no integral damage occurs. Timber preservatives Due to the aggressive nature of some timber preservatives, timber fascias treated with preservatives MUST be allowed to dry before fixing OSM Rainwater systems gutter and fittings. Refer to manufacturers recommendations. OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 DESIGN elow Ground Drainage Connectors Roof outlets Materials 63

64 GOOD SITE PRCTICE Handling Storage Safety Maintenance Handling and Storage Handling Care should be taken when handling gutter and pipe. Excessive scratching or scoring harms the appearance and can also affect the joint sealing. Take extra care when handling gutter and pipe in wintry conditions. Cold weather reduces the impact strength of plastics. Load and unload loose gutter or pipe by hand. void using skids. When loose pipes have been transported one inside the other, always remove the inner pipe first. (See Fig. 24) Fig. 24 Unloading of block bundles Storage lways store gutter or pipe on a reasonably flat surface free from sharp projections. Fig. 25 Storage of loose pipe on the ground 2m or 7 layers max. 2m lock bundles lock bundles can be stored up to 3 high without extra side supports or bearers. lock bundles will remain free-standing when cut. Take care when releasing bundles as the straps are under considerable tension and may flail when cut. Fig. 26 Storage of loose pipe on bearers Loose gutter or pipe Loose gutter or pipe requires side supports at least every 2m. These supports should consist of battens at least 75mm wide. Ideally, support loose gutter or pipe uniformly throughout its entire length. If this is not possible, place timber supports at least 75mm wide at 1m maximum centres beneath the gutter or pipe. Fittings Store fittings supplied in plastic bags away from direct sunlight. If this is not possible, open bags to prevent a build-up of temperature. Store silicone lubricant in a cool place away from any heat source and out of direct sunlight. 1m spacing maximum 75mm bearing width Safety and Maintenance Safety The relevant regulations detailed in the Health and Safety at Work ct 1974 must be adhered to on site. In particular ensure ladders are properly positioned and secured. Removing Old Guttering Remove old gutter with care (especially if cast iron) and recycle if possible. Check condition of fascia: replace as necessary or use multi-hole screw fixings. Maintenance OSM Rainwater systems are designed to be maintenance-free. However, in wooded or leafy areas, gutters should be periodically checked to ensure that gutter and pipe have not worked loose or become blocked. 64 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

65 GENERL TECHNIQUES Gutter Jointing Gutter Jointing Gutter joint design The OSM joint fittings are supplied complete and ready for use. The flexiclip method of gutter jointing enables easy connection of gutter to fittings. It is not necessary to remove the clip from the fitting in order to make the joint. To make the joint, flex the clip rather than the whole component. This ensures a positive, permanently watertight joint. (See Fig. 27) Fig. 27 Flexiclip gutter joint Thermal expansion ll fittings must be firmly secured to counter the effects of accumulated thermal movement. llowance for thermal expansion must be made when fixing the gutter. Gutter joint fittings have a line marking the position to which the gutter should be inserted. gutter jointing bracket or gutter union with bracket should be fitted within 300mm from the end of terminal lengths of gutter. Fig. 28 llowance for thermal movement Fixing Gutter Jointing rackets Gutter Jointing rackets 0T005, 4T805, and 3T305 have a single screw fixing, allowing the fitting to pivot to the required gutter fall. (See Fig. 30) Use 1" Nº.10 rustless roundhead screws for wooden fascia, and refer to manufacturers instructions for plastic fascia. Fig. 30 Fixing Gutter Jointing racket (0T005) Expansion gap Gutter Gutter Cutting lengths of gutter Lengths of gutter can be cut to fit as necessary. Use a fine-toothed hand saw and ensure that the cut is clean and square. De-burr the cut end with a scraper. Gutter fall Laying OSM gutter systems to a fall of 1:600, 25mm in 15m, is recommended. This will increase the flow capacity and increase the area of roof that can be drained, particularly if the downpipe is positioned centrally. It will also prevent silting (Refer to Flow Capacity Tables pages 55). Gutter connection Connecting the gutter PROCEDURE 1. Lay the gutter to the gutter end line and place it under the part of the clip nearest the fascia. 2. Pull the gutter down with the fingers whilst simultaneously pushing the clip over the gutter with the thumbs. (See Fig. 29) 3. Ensure edge of under-felt or membrane is dressed into gutter Fig. 29 Connecting SquareLine Gutter 4T805 Fixing Gutter Unions Support Gutter Unions 0T009, 4T809, 5T509, 6T609, 8T809 and 9T909 at their centre with a Support racket, allowing the fitting to pivot to the required gutter fall. lso fix Support rackets within 1m of both sides of all gutter joints. (See Fig. 31) Fig. 31 Installation of RoundLine Gutter Union 0T019 0T009 1 metre max 1 metre max OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 SITEWORK Good Site Practice General Techniques: Gutter Jointing 65

66 GENERL TECHNIQUES Gutter Connection Gutter Connection to Other Materials Connection to metal gutters RoundLine and SquareLine only PROCEDURE 1. Clip PVC-U gutter into the appropriate connector (see Figs. 32/33) 2. olt this to the metal gutter 3. Seal the bolted joint with waterproof mastic. Using Half-round Connector 0T008 olt either outside the spigot end or inside the socket end of the metal gutter. Using Ogee Connector 0T014 (left hand), or 0T015 (right hand) olt inside or outside the metal gutter depending on its size: 4" ogee gutter: fit Connector to the outside of both socket and spigot. 4 1 /2" ogee gutter: fit Connector inside the socket and outside the spigot. 5" ogee gutter: fit Connector on the inside of both socket and spigot. Connection to PVC-U gutter RoundLine only Use RoundLine true half-round Connector 0T018 to connect to 100mm true halfround PVC-U gutter. Fig. 32 Connection to cast iron gutter RoundLine Gutter 150mm 0T019 Fig. 33 Connection to cast iron gutter 150mm 4T819 4T815 Cast iron gutter 0T008 SquareLine Gutter Cast iron gutter Gutter Support Gutter support order of fixing Fig. 34 General arrangement SquareLine system PROCEDURE 4T806 4T Fix the support bracket furthest from the outlet first. 2. llow for the required fall. 4T803 4T Ensure that sufficient space is left below the roof tiles to fix the gutter. 4T811 4T819 4T872/874 4T810 4T825 IMPORTNT NOTE: Due to the aggressive nature of some timber preservatives, it is essential that timber fascias that have been treated with preservatives are allowed to dry before fixing PVC-U gutter fittings. *NOTE: Rainwater pipe which discharges into a gully must terminate ELOW the gully grating but OVE the water seal, preferably by using a back inlet. (S EN 12056:3: ) 4T825 4T882/4T884 4T886/4T888 4T823/824 4T833/834 4T832* 66 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

67 GENERL TECHNIQUES Gutter Support Gutter Support Installation Methods Support rackets PROCEDURE 1. String a plumb line along the base of the bracket. 2. Then securely screw fix at 1m (maximum) centres. Use 1 Nº.10 rustless roundhead wood screws. NOTE: Use multi-screw fixings on high buildings or in areas subject to high winds. See page 8 for component selection. racket Spacers RoundLine, SuperLine, RoofLine, DeepLine, SquareLine, StormLine and Mini-Fit Each spacer as supplied will extend OSM Gutter Jointing rackets, Gutter Support rackets and Running Outlets by 21mm. Two Gutter racket Spacers stacked together will give an overall spacing of 40mm. Individual spacers can be cut back to a minimum of 10mm depth. Fixing should be via Nº.10 rustless roundhead wood screws of appropriate length for the number of spacers used. It is recommended that no more than two Gutter Spacers are put together in one installation. Fig. 35 Gutter racket Spacers Spacer 0T044 ngled fascias Where dwellings are designed with angled fascias, place an ngled racket Spacer 0T045 behind Gutter Union and Support rackets to bring them into the horizontal position. (See Fig. 36) 1 1 /2" Nº.10 rustless roundhead wood screws are recommended for this fixing. Fig. 36 pplication of ngled racket Spacer ngled fascia Gutter Jointing or Support racket 0T045 Snow ll OSM Rainwater systems are designed to withstand the weight of snow likely from normal falls. However, in areas subject to heavy snowfalls, the distance between support brackets should be reduced to 750mm or less. S12056: Part 3: 2000 section N4, 7.7 and gives details of precautions which should be taken to prevent the accumulation of snow on roofs. These include the use of snowboards and snowguards. Rise-and-Fall rackets RoundLine, SuperLine, RoofLine, DeepLine, SquareLine and StormLine Rise-and-Fall rackets comprise of a ow and Pin, fixed to the wall using either uildin Spikes or Drive-in Spikes. (See Fig. 37) Incorporate uild-in Spikes within the mortar joint below the last-but-one brick course during construction of the wall. Drive-in Spikes are designed for installation in an existing wall. Drive the spike into the mortar joint below the last-but-one brick course. Fig. 37 Rise and Fall racket ssembly ow and Pin Drive-in or uild-in Spike Fig. 38 Installation of Rise and Fall rackets 6T609 Gutter Support racket Connecting the ow and Spike The threaded rod of the ow allows easy screw connection to the Spike. The threaded connection enables the ow to be raised or lowered to give the gutter the required fall. (See Fig. 37) Support centres Rise and Fall rackets should be placed to support the centre of the Gutter Union and to provide intermediate support at maximum 1m centres. 1 metre max Gutter Support - Installation Methods continued overleaf OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 SITEWORK General Techniques: Gutter Connection Gutter Support 67

68 GENERL TECHNIQUES Gutter Support Gutter Support Installation Methods (cont.) Rafter rackets RoundLine, SuperLine, RoofLine, DeepLine and SquareLine only Designed for use when there is no fascia board, and as an alternative to Rise-and- Fall rackets. Rafter rackets are galvanised for protection against corrosion. Top Rafter rackets and Side Rafter rackets have a 30 angle and are 300mm in length. They are available in plain and adjustable format. Top Rafter rackets Must be fixed before the roof is tiled. (See Fig. 39) NOTE: If a fall is required, use the djustable Top and Side Rafter rackets djustable Top and Side Rafter rackets 0T147 and 0T148 RoundLine, SuperLine, RoofLine, DeepLine, SquareLine and StormLine djustable rackets have a slotted hole in the front face. This is fitted with a rust-proofed wing nut and bolt for connection to a Gutter Support racket. (See Figs. 40/41) To achieve a fall, release the wing nut and adjust the bracket up or down as necessary. Fig. 40 djustable Top Rafter racket (0T147) Top Rafter racket Side Rafter rackets May be fixed after roof has been tiled. They are particularly useful when replacing the gutter on an existing building. To achieve a fall, alter the position of the rackets on the side of the rafters. (See Fig. 42) Fig. 42 Side Rafter racket (0T246/746) 0T009 Fig. 39 Top Rafter racket (0T245/745) djustment screw Gutter Support racket Fig. 41 djustable Top Rafter racket (with SquareLine Union and Support racket) 0T147 4T819 4T809 Hints and tips Screws Use 1" Nº.10 rustless roundhead wood screws to fix rackets, Outlets and ngles. For correct screws to use with plastic fascias seek fascia manufacturer s advice. Power tools Power tools can be used to install OSM guttering. For correct torque setting on plastic fascias, seek manufacturer s advice. Lubricating seals ssembly is easier if the seal is lubricated using OSM Silicone Spray. Lubricant also improves service life and efficiency of seals. Rainwater Diverter This is an excellent, environmentally friendly method of collecting roof water for garden use, whilst still ensuring flow to underground drainage if the storage unit is full. Water test Don t wait for a downpour do a water test of new guttering before removing the ladder. Support centres Rafter rackets should be positioned to support the centre of the Gutter Union and to provide intermediate support at (maximum) 1m centres. NOTE: Due to the design criteria of rafters, if 1m spacing cannot be obtained, the smaller dimension should prevail, i.e. 600mm. 68 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

69 GENERL TECHNIQUES Downpipe Cutting and Jointing Downpipe Cutting and Jointing Pipe cutting Pipe may be cut on site using a fine-toothed hand saw. PROCEDURE (See Fig. 43) 1. Cut pipe cleanly at right angles to its axis. 2. De-burr the cut end with a scraper. If the cut end is to be inserted into a ring-seal or push-fit joint. 3. Chamfer the spigot end: this is essential to ensure that the sealing ring is not displaced during insertion. Fig. 43 Pipe preparation Chamfer and deburr spigot end Cut pipe square Thermal expansion Provision for thermal expansion must be made when installing PVC-U downpipe. Leave a gap of 10-12mm between the top of each pipe length and the fitting to which it is connected. Pipe joint design RoundLine, SuperLine, DeepLine, StormLine These systems utilise 68mm [2 1 /2"] circular pipe and fittings. The Pipe Connector, ranch and all ends have an aperture socket which gives an interference fit, eliminating any need for solvent welding. This provides a neat and streamlined joint, concealing the required 10mm expansion gap between downpipe and fittings. SquareLine and StormLine 61mm square pipe is joined with Pipe Connector 4T823/824 which has a socket at the upper end, an aperture socket at the lower end, and an integral fixing bracket. The pipe may be fixed flush to the wall or, using stand-off components 4T833/824, fixed standing off from the wall. The SquareLine system can also be used, via an adaptor, with 68mm circular pipe. Fig. 44 Pipe Connector (4T823) Mini-Fit Utilising 55mm circular pipe, the Mini-Fit system Pipe Connector and ends have an aperture socket designed to conceal the 10mm expansion gap between pipe and fittings. RoofLine and Roof Outlets Utilise pipe and fittings from the OSM 82 and 110mm Soil systems. See opposite for ring-seal and solvent weld jointing. Jointing procedures RoundLine, SuperLine, DeepLine, StormLine Use a Pipe Connector 0T024 supported by a Socket racket 0T033/038. Ensure 10-12mm expansion gap is provided. Mini-Fit Use Pipe Connector 2T104, supported by Pipe racket 2T082. SquareLine and StormLine Ensure 10-12mm expansion gap is left between the top of each pipe and the fitting to which it is connected. RoofLine and Roof Outlets See opposite for ring-seal and solvent weld jointing. Connection to Gutter Outlets RoundLine Plain ended pipe connects directly to the sockets of the Running Outlet 0T624, the Swivelock Running Outlet 0T625 and the Stopend Outlet 0T007. SuperLine Plain ended pipe fits over the spigot of the Running Outlet 5T508. DeepLine Plain ended pipe connects directly to the socket of the Running Outlet 9T906. Mini-Fit Plain ended pipe fits over the spigot of the Running Outlet 3T306 and Stopend Outlet 3T307. RoofLine Plain ended pipe fits over the spigot of the Running Outlet 6T606. SquareLine (See Fig. 45) Plain ended pipe connects directly to the sockets of the Running Outlet 4T806 and the Stopend Outlet 4T807. To connect to 68mm circular pipe, use Square-to- Round daptor 4T837, which fits directly into the socket of the outlet. Fig. 45 ssembly of offset - SquareLine StormLine Pipe off-cut 4T825 Plain ended 68mm circular and 61mm square pipe connects directly to the sockets of the Running Outlet 8T806 and the Stopend Outlets 8T807/808. OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 SITEWORK General Techniques: Gutter Support Downpipe Cutting 69

70 GENERL TECHNIQUES Pipe Jointing Installation of Rainwater Diverter Kit RoundLine, SuperLine, DeepLine, SquareLine and StormLine PROCEDURE 1. Position waterbutt at required height 3. Drill a 26mm hole 80mm down from the next to downpipe. top rim of the waterbutt. 2. Cut away a 30mm section of downpipe, 4. Fit the waterbutt connector and washer 30mm below the top rim of the from the inside. waterbutt and insert the downpipe 5. Fit the nut from the outside: tighten nut connector. to form a seal. 6. Cut the connecting hose to the required length and fit between butt and downpipe connection. IMPORTNT NOTE: Diverter Kit not suitable for cast iron drainpipes. Pipe Jointing Jointing 82mm and 110mm Pipe oth RoofLine gutter system and OSM Roof Outlets connect to OSM 110mm PVC-U soil pipe and fittings. OSM Roof Outlets also connect to OSM 82mm PVC-U soil pipe and fittings. Joints in lengths of 82mm and 110mm pipe may be formed by: Ring-seal, push-fit jointing OR Solvent weld jointing Three sockets are available: D/SW Double Socket 3S/4S104 D/S Double Socket 3S/4S105 (slip coupler for repair applications) S/SW Single Socket 3S/4S124 (for creating a fixed ring-seal joint on plain-ended pipe or fittings). Ring-Seal/Push-Fit Jointing PROCEDURE 1. Ensure any pipe cut on site is also chamfered. 2. Check that the sealing ring is properly seated in its housing in the socket of the fitting. 3. Ensure all components to be joined are dry, clean and free from grit or dust. Note any deep scratches on the pipe or fitting spigot as these may prevent the sealing ring from forming a water tight seal. 4. Lubricate evenly around the pipe or fitting spigot end with Silicone Lubricant 4S391. Do NOT lubricate inside the socket. Do NOT use washing up liquid as a lubricant. 5. Correctly align the components to be joined. 6. Push the pipe or fitting spigot fully into the socket. Mark the pipe or fitting spigot at the socket face and then withdraw it by a minimum of 12mm. 7. Make a subsequent check to ensure that the expansion gap is not lost during further installation work. Silicone Lubricant llowance 50g tube 4S391: Sufficient for 9 joints of 110mm pipe and 16 joints of 82mm pipe Silicone Lubricant Spray 400ml can 4S392: Spray the lubricant onto the spigot and not the ring seal. The spigot can then be inserted into the socket. fter installation ensure the pipework is thoroughly flushed through with clean water. Solvent Weld Jointing PROCEDURE 1. efore using any solvent based cleaners or cement: Read instructions on the can Ensure there is sufficient ventilation. 2. Make sure pipe or fitting spigot and solvent weld socket are dry, clean and free from grit or dust. 3. Clean surfaces of spigot and socket with Degreasing Cleaner Nº.1 4S379/380. pply liberally using a clean non-synthetic rag or absorbent paper. 4. pply one coat Solvent Cement Nº.2 4S383/384/385. pply an even coat to both surfaces using the applicator provided or a paint brush. Stroke the cement LONG and not around the surfaces. 5. Immediately insert pipe or fitting spigot fully into the socket. Each solvent weld joint MUST be completed within 1 1 /2 minutes. 6. Hold for seconds. Remove any surplus cement from the mouth of the socket. 7. The joint may be handled after 10 minutes and commissioned after 24 hours. Degreasing Cleaner llowance (approx.) Nº.1-125ml can 4S379: Sufficient for 16 joints of 110mm pipe Nº.1-250ml can 4S380: Sufficient for 32 joints of 110mm pipe Solvent Cement llowance Nº.2-125ml can 4S383: Sufficient for 5 joints of 110mm pipe Nº.2-250ml can 4S384: Sufficient for 11 joints of 110mm pipe Nº.2-500ml can 4S385: Sufficient for 22 joints of 110mm pipe Safety When making solvent weld joints it is essential to observe normal safety rules for handling solvent: Never smoke or bring naked flames near the area of work Work in a well ventilated area to avoid inhaling fumes Close the solvent container after use and store in a cool area Do not allow solvents or cleaners to come into contact with skin Refer to COSHH Regulations (Control of Substances Hazardous to Health) where applicable. 70 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

71 GENERL TECHNIQUES Pipe Support Offsets Pipe Support and Offsets Pipe support centres Refer to Table 11 below for the maximum support centres for pipes. Table 11: Maximum Pipe Support Centres Maximum centres (m) Pipe Size Vertical Horizontal 55mm mm Eaves without soffit For 68mm Circular Pipe Keep rainwater pipe parallel to the wall by fitting a racket Spacer 0T031 behind the Pipe racket or Pipe/Socket racket (See Fig. 48). The racket Spacer moves the pipe 36mm further away from the wall and puts it directly in line with the gutter outlet. 68mm 82mm 110mm Fig. 48 pplication of Pipe racket Spacer RoundLine, SuperLine, DeepLine, StormLine For 68mm Circular Pipe, the concealed Pipe or Socket racket 0T033, or Pipe racket 0T034 may be used. (See Fig. 46) Fig. 46 Pipe or Socket racket (0T033) SquareLine and StormLine On installations featuring tudorised beams on external walls, it may be necessary to use a Pipe racket Spacer 4T731 (See Fig. 47). This is designed for use with the Pipe racket, Pipe Connector and Pipe Shoe. The Pipe racket Spacer can be adjusted by cutting to the required depth. Fig. 47 Use of Pipe racket Spacer 5T508 0T030 0T033 0T033 0T030 For 61mm Square Pipe On installations where the fascia board is fitted to an external wall, or where there is a small eaves projection, use Pipe Wall Offset 4T836. Pipe Support & Offsets continued overleaf OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 SITEWORK General Techniques: Pipe Jointing Pipe Support & Offsets 71

72 GENERL TECHNIQUES Pipe Support Offsets Pipe Support and Offsets continued Offsets ssemble offsets using Offset ends. Where necessary, to provide the necessary projection, include a length of pipe offcut to suit. (See Figs. 50/51/52 for typical examples). For a complete list of components and minimum achievable offsets, see pages Fig. 50 ssembly of offset - SquareLine Offset support To ensure offsets are adequately supported, fit a Pipe/Socket racket around the pipe directly below the lower Offset end. Fig. 52 Offset on deep fascia 0T624 Pipe off-cut 0T026 Pipe off-cut to suit 4T825 0T025 0T034 Fig. 51 RoofLine shallow offset 137mm min 4S444 SquareLine When using a SquareLine Pipe Wall Offset 4T739, support is provided by a Pipe Connector and racket 4T824 which features an integral fixing bracket. Pipe Wall Offset with access 4T858 contains an integral bracket. 72 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

73 SYSTEM CONNECTIONS To elow Ground Drainage Connections to elow Ground Drainage Downpipes may be terminated at ground level by using an adaptor, a pipe shoe, feeding directly into a gully or directly into a drain socket. COMPONENTS For the full range of required components, system requirements and compatibility, see page 74 of this Guide. Using Rainwater daptor 4D149/0T149 The daptor can be used with either a spigot or socket of a 110mm pipe. 68mm Circular Pipe (See Fig. 53). PROCEDURE 1. Fit the daptor over the spigot or socket. 2. Fit the end of the 68mm Circular pipe into the plain socket of the daptor. Lubrication or solvent welding is not necessary. Fig. 53 Connection to 110mm PVC-U Spigot (68mm circular pipe) 68mm downpipe 4D149 SquareLine 61mm Square Pipe (See Figs. 54/55). PROCEDURE 1. Fit the daptor over the spigot or socket. 2. Fit Drain daptor 4T836 Square to Round into the plain socket of the daptor. 3. Place the 61mm SquareLine pipe into the Drain daptor. Pipe Wall Offset 4T838, or Pipe Wall Offset with access 4T858 can be used to connect pipe to drain position as required. Fig. 54 Connection to 110mm PVC-U Socket (61mm square pipe) Coupler 4D205 61mm SquareLine pipe 4T836 4D mm plain ended pipe Fig. 55 Connection to 110mm PVC-U Spigot (61mm square pipe) 110mm plain ended pipe 61mm SquareLine pipe 4T836 4D149 end with double socket 4D mm pipe 110mm pipe 4D561 end with double socket 4D561 Connections to elow Ground Drainage continued overleaf OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 SITEWORK General Techniques: Pipe Offsets System Connections 73

74 SYSTEM CONNECTIONS To elow Ground Drainage Connections to elow Ground Drainage continued Using Universal Drain daptor 4D159 The Universal Drain daptor is suitable for connecting both circular and square section pipe, up to 70mm. It can be fitted onto a 110mm pipe spigot or socket, but is suitable for EXTERNL applications only. 68mm Circular Pipe (See Fig. 57). PROCEDURE 1. Ensure the 68mm Circular pipe is free from swarf. 2. Place the pipe into the daptor, working the pipe through the opening, until the pipe is located in the adaptor to a suitable depth. 3. Fix a Pipe racket 0T034 no more than 150mm from the daptor. Fig. 57 Connection of 68mm circular rainwater pipe 61mm Square Pipe (See Fig. 58). PROCEDURE 1. Using the cutting guides located on the underside of the daptor, cut the daptor to the required size. 2. Fit the daptor to either a 110mm drain spigot or 110mm socket. 3. Ensure pipe is free from swarf. 4. Place the pipe into the daptor, working the pipe through the opening until the pipe is located in the daptor to a suitable depth. 5. Fix Pipe racket 4T833/834 no more than 150mm from the daptor. Fig. 58 Connection of 61mm square rainwater pipe Pipe Shoe Provides open discharge* from downpipe. (See Fig. 59). PROCEDURE 1. Locate Pipe Shoe centrally over gully. 2. Fix securely to wall using Pipe racket. Fig. 59 Pipe Shoe over Gully (68mm circular pipe illustrated) 68mm downpipe 0T038 4D507 0T037 Ground Level 68mm RoundLine pipe Ground Level 61mm SquareLine pipe *NOTE: Rainwater pipe which discharges into a gully must terminate ELOW the gully grating but OVE the water seal, preferably by using a back inlet. Where discharge onto a lower roof or paved area is unavoidable, fit a pipe shoe to divert water away from the building and reduce splashing. 4D159 Universal Drain daptor 4D159 Universal Drain daptor Connection to ottle Gully The rainwater downpipe or Pipe Wall Offset can be connected to a ottle Gully (See Fig. 60). PROCEDURE 1. Remove a section of the ottle Gully 4D561 4D561 grating so that the downpipe sits neatly below the grating. 2. Position a pipe bracket no more than 150mm from the grating. Fig. 60 Connection to ottle Gully (68mm Circular pipe illustrated) 68mm RoundLine 0T034 ottle Gully 4D CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

75 SYSTEM CONNECTIONS To elow Ground Drainage Connections to elow Ground Drainage continued Connection to Vertical Inlet Hopper The rainwater downpipe or Pipe Wall Offset can also be connected to a Vertical Inlet Hopper (See Figs. 61/62). PROCEDURE 1. Cut a hole in the back plate. 2. Insert the pipe making sure discharge is below the grating. Fig. 61 Connection to ottle Gully (68mm circular pipe illustrated) RoofLine Connection to 110mm Drain Socket OSM RoofLine system utilises OSM 110mm Soil pipe. This can be connected directly into a drain socket (See Fig. 63). Fig mm Connection to PVC-U Drain Socket 110mm RoofLine pipe elow Ground Drainage end 4D561 68mm downpipe Vertical Inlet Hopper 4D508 Fig. 62 Connection to ottle Gully (61mm square pipe illustrated) 61mm SquareLine pipe 4T838 Vertical Inlet Hopper 4D508 OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 SITEWORK System Connections: To elow Ground Drainage 75

76 SYSTEMS CONNECTIONS Connections to existing Iron Pipe Roof Outlets Connections to Existing Iron Pipe 68mm Circular Pipe RoundLine, SuperLine, DeepLine, StormLine Systems Rusty or cracked cast iron pipe may be replaced easily with PVC-U. ny sound part of an existing cast iron system can be retained and 68mm PVC-U pipe connected directly to the open socket of a 2 1 /2" iron pipe. Mastic or other sealing compounds are not needed. 110mm Circular Pipe RoofLine, OSM Roof Outlets To 4" Cast Iron Spigot COMPONENTS Connector 4S134 and Gasket 4S119 from the OSM Push-Fit Soil range. PROCEDURE 1. Fit the Gasket over the spigot of the iron pipe. 2. Push the Connector firmly onto the pipe. 3. Heat the socket of the Connector evenly all round until it shrinks to fit tightly around the seal and iron pipe. To 4" Cast Iron Socket COMPONENT Connector 4S206 from the OSM Push-Fit Soil range. PROCEDURE 1. Fit Connector to the PVC-U pipe. 2. Push firmly into the socket. Roof Outlets OSM Roof Outlets are suitable for installation into any type of flat roof construction provided that there is adequate support. Typical constructions include mastic asphalt roofing and built-up roofing (See Fig. 64). Mastic asphalt roofing PROCEDURE 1. If not cast in-situ, ensure the outlet is suitably supported by shaping the concrete slab to receive the body. The flange may rest on top of the screed no recess is required. Outlet Min. size of hole required 82mm 185mm 110mm 240mm Fig. 64 Roof Outlet installation a) Mastic asphalt roof 2. Drill four equally spaced counter sunk holes (Nº.10 size) in centre of flange. 3. Fix Outlet to roof decking using 1" Nº.10 rustless screws. Remove grating. 4. Dress first layer of asphalt up to and over the flange. Feather on the outer edge of the mouth recess. 5. Dress second layer of asphalt over the first. Finish by trowelling to a radius into the mouth recess. 6. Replace and secure grating. b) uilt-up roof uilt-up felt roofing PROCEDURE 1. Provide a hole in the roof suitably dished to give support to the body and recess the flange level with the top of the roof deck. 2. Drill four equally spaced counter sunk holes (No.10 size) in centre of flange. 3. Fix Outlet to roof decking using 1" No.10 rustless screws. Remove grating. 4. Lay the first two layers of felt across the flange and into the mouth recess. 5. Lay the third layer and dress down into the mouth of the body. This will adhere to the Outlet with bitumen. 6. Replace grating over the third layer of felt and secure. Two layers mastic asphalt Grating retained by captive non-corrosive bolt uilt-up roof; timber, felt and chippings Grating retained by captive non-corrosive bolt 4S414 Third layer of felt retained by grating 4S414 Screed Concrete 4S124 4S083 4S CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

77 GENERL PVC-U RINWTER TECHNIQUES SYSTEMS Gutter General Jointing Information Connects to 68mm circular downpipe Materials ll gutter, pipe and most fittings in OSM Rainwater systems are manufactured from PVC-U (Unplasticised Polyvinyl Chloride). cceptance OSM Rainwater systems comply, where applicable, with the requirements of the following ritish Standards: S 6209: 1982 Solvent cement for non-pressure thermoplastics pipe systems S : 2000 Plastics piping systems for soil and waste drainage S EN 607: 2004 Eaves, gutters and fittings made of PVC-U definitions, requirements and testing. pproval pending. S EN 1462: 2004 rackets for eaves gutters: requirements and testing. pproval pending. S EN : 2000 Plastics rainwater piping systems for above ground external use unplasticized Poly Vinyl Chloride (PVC-U) Part 1 specification for pipes, fittings and the system. pproval pending. The ritish Standard Kitemark identifies gutter, pipe and fittings that are manufactured under the SI certification scheme. Health and Safety The relevant provisions of the following legislation should be adhered to on site: Construction (Design and Management) Regulations 1994 Control of Substances Hazardous to Health Regulations 1988 Health and Safety t Work ct 1974 Management of Health and Safety t Work Regulations 1999 How to Order Manual Handling Operations Regulations 1992 References OSM Rainwater systems should be designed and installed in accordance with the guidance provided in the appropriate sections of the following: uilding Regulations 2000 (England and Wales): pproved Document H, Part H3 uilding Standards (Scotland) Regulations (including current amendments: Technical Standards Part M) uilding Regulations (Northern Ireland) 2000: Technical ooklet N S 8000 Workmanship on uilding Sites: Part 13: 1989 Code of Practice for above ground drainage and sanitary appliances S EN 752: 1997 Code of Practice for building drainage S EN 12056: 2000 Gravity drainage systems inside buildings: Part 3 Roof drainage, layout and calculation Disposing of rainwater: GG 38. Watford, RE 2000 Painting plastics: IP 11/1979. Watford, RE 1979 Water Regulations Guide: London, Water Regulations dvisory Scheme, 2000 Hazards associated with PVC-U There are no particular hazards associated with handling, cutting or working with PVC-U products, and protective clothing or equipment is not normally required. Copies of Safety Data Sheets covering PVC-U, solvent cements and cleaners are available from Wavin Technical Design Department. Contact Wavin Technical Enquiries. bbreviations P/E: Pipe and fittings with both ends plain or with one plain end and one special end. S/S: Pipe and fittings with one or more ring-seal or push-fit sockets, but always one plain or special end. D/S: Fittings with ring-seal or push-fit sockets at all ends. S/SW: Fittings with one or more ring-seal sockets but always one solvent socket. SW/S: Fittings with one or more solvent sockets and one plain or special end. D/SW: Fittings with solvent sockets at all ends. Supply ll OSM systems are supplied through a nationwide network of merchant distributors. For details of your nearest stockist, contact Wavin Customer Services. Special fabrication specially fabricated angle or fitting may be required for certain installations. Where possible, Wavin is happy to provide such fabrications to Customer design. However, no responsibility can be accepted for their function. For further details of this service, contact Wavin Technical Enquiries. Sealing Rings Where applicable, Sealing Rings are supplied fitted to each component and are included in the price. Conditions of sale The Company will not accept responsibility for the malfunction of any installation which includes components not supplied by Wavin Plastics Limited. Goods are sold subject to Company conditions of sale. Each product is identified by a Part Number, followed by (where relevant) a colour reference to provide the full Catalogue Code. Colour reference codes are as follows: Colour Ref. Code lack Grey G Olive E White W rown N EXMPLE: The Part Number for a 2m length of RoundLine Gutter is 0T072. This is available in a choice of four colours: lack (), Grey (G), White (W) and rown (N). To order 5 x 2 metre lengths of lack RoundLine gutter, simply quote: Quantity required plus Catalogue Code (i.e. Part Number with the Colour Reference Code added) plus Description Thus, the order would be: 5 x 0T072 RoundLine Gutter. To place an order, contact the Wavin Customer Services Tel: Fax: OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 SITEWORK System Connections General information 77

78 PVC-U RINWTER SYSTEMS General Index Gutter Profiles DeepLine Page No Downpipe system (68mm Circular) Gutter 33 Gutter ngles 35 Gutter racket Spacers 33 Gutter Support racket 33 Gutter system Gutter Union 33 Outlet 34 Rafter rackets 34 Rise-and-Fall racket 34 Spares 35 Spikes 34 Stopends RoofLine Downpipe system (110mm Circular) Gutter 23 Gutter ngles 25 Gutter racket Spacer 23 Gutter Support racket 23 Gutter system Gutter Union 23 Outlet 24 Rafter rackets 24 Rise-and-Fall racket Spares 25 Spikes Stopends 25 RoundLine Page No Connectors (to other gutters) 12 Downpipe system Gutter 10 Gutter ngles Gutter racket Spacers Gutter Jointing racket 10 Gutter Support racket 10 Gutter system Gutter Union 10 Leaf Guard 14 Outlets Rafter rackets Rise-and-Fall racket 11 Spares Spikes 11 Stopends 13 SquareLine Connectors (to other gutters) Downpipe system (61mm Square) Gutter 36 Gutter ngles 39 Gutter racket Spacer 36 Gutter Jointing racket 36 Gutter Support racket 36 Gutter system Gutter Union 36 Outlets 38 Rafter rackets 37 Rise-and-Fall rackets 37 Spares 39 Spikes 37 Stopends 38 StormLine Page No Downpipe system 40 43/15 18 (61mm Square and 68mm Circular) Gutter 44 Gutter ngles Gutter racket Spacers 44 Gutter Support racket 44 Gutter system Gutter Union 44 Outlet 46 Rafter rackets 45 Rise-and-Fall racket 45 Spares 47 Spikes 45 Stopends 46 SuperLine Downpipe system (68mm Circular) Gutter 19 Gutter ngles Gutter racket Spacers 19 Gutter Support racket 19 Gutter system Gutter Union 19 Outlet 21 Rafter rackets Rise-and-Fall racket 20 Spares 22 Spikes 20 Stopends 21 Roof Outlets Domed Roof Outlet 48 Downpipe system (82mm and 110mm Circular) 78 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL

79 GENERL PVC-U RINWTER TECHNIQUES SYSTEMS Gutter General Jointing Index Connects to 68mm circular downpipe Downpipe Systems 55mm Circular Page No alloon Grating 32 ends 32 Connector 31 Downpipe 31 Downpipe system Gutter system: Mini-Fit Hopper Head and daptor 32 Offset end 32 Pipe rackets 31 Pipe Shoe 32 61mm Square ccess Pipe 43 daptors end ranch 42 Connectors Downpipe 40 Downpipe system Gutter system: SquareLine StormLine Hopper Head 43 Offset ends 42 Pipe racket Spacer 40 Pipe rackets 40 Pipe Shoe 42 Rainwater Diverter Kit 43 68mm Circular Page No ccess Pipe 18 daptors 16 end 17 ranch 18 Connectors 16 Downpipe 14 Downpipe system Gutter system: DeepLine Gutter system: RoundLine Gutter system: SuperLine Gutter system: StormLine Hopper Head 18 Offset ends 17 Pipe rackets Pipe Shoe 17 Rainwater Diverter Kit 18 Socket rackets Waterbutt Filler Kit 18 82mm Circular Page No ranches 51 Connectors Domed Roof Outlet 48 Downpipe system Downpipe 48 Hopper Head 51 Offset ends 50 Pipe rackets Pipe Shoe 51 Reducer 50 Socket rackets Sockets mm Circular ranches 28 29, 51 Connectors 27, Downpipe system 26 27, Downpipe 26, 48 Gutter system: RoofLine Domed Roof Outlet 48 Hopper Head 29 Offset ends 28, 50 Pipe rackets 26, Pipe Shoe 28, 51 Reducer 27, 50 Socket rackets 26, Sockets 26 27, 49 ncillaries Cleaner 52 Gutter Spares Lubricant 52 Pipe Spares 53 Solvent Cements 52 OSM RINWTER SYSTEMS Product, Design & Installation Guide 2007 SITEWORK General Index 79

80 PVC-U RINWTER SYSTEMS Supporting Information Supporting Information Page No bbreviations 77 cceptance 77 djustable Rafter rackets 68 ngled fascias 56, 67 lock bundles storage/handling 64 racketing rrangements [Table 4] 56 uilt-up felt roofing 76 Calculating Effective Roof rea 54 Chemical resistance 63 Conditions of sale 77 Connection of Gutter Outlets 58, 59, 60 to OSM Pipe Connections to elow 62, 73, 74, 75 Ground Drainage - to 110mm circular iron pipe 76 - (RoofLine) to 110mm drain socket 75 - to 68mm circular iron pipe 76 - to ottle Gully 74 - to Vertical Inlet Hopper 75 Connections to elow Ground Drainage - Fittings [Table 10] 62 Connections to Other Gutter Types 57 Connections to Other Materials (gutters) 66 - to metal gutters 66 - to PVC-U gutters 66 Connections to Other Materials (pipe) 61 - to existing clay socket 61 - to existing iron pipe 61 Curved eaves 57 Deep Offsets 60 Deep Offset Components [Table 9] 60 Determining Gutter Flow Capacity Downpipe Cutting and Jointing 69 Eaves without soffit 71 Effective Roof rea [Table 1] 54 Fittings storage 64 Fixing Gutter Jointing rackets 65 Fixing Gutter Unions 65 Flat roof drainage 76 Flat roofs 55 Flow rates 55 Page No General Information 77 Gutter racket Spacers 67 Gutter Connectors [Table 5] 57 Gutters: - connection 65 - cutting lengths 65 - factors to consider 55 - fall 65 - joint design 65 - location 56 - location of outlets 55 - support centres 56, 58, 68 - support options 56 - thermal expansion 65 - thermal movement 57 Gutter Flow Capacity [Table 3] 55 Gutter Jointing 57, 65 Gutter Jointing rackets 65 Gutter Outlets 55 Gutter Unions 65 Gutter Support 56, 57, 67 - angled fascias 67 - location 56 - order of fixing 66 - screws 68 - snow 67 - support centres 56, 58, 68 - support options 56 Gutter Support rackets 67 Handling 64 Hazards associated with PVC-U 77 Health & Safety 77 How to Order 77 Indirect connections (to G Drainage) 62 Jointing 82mm/110mm Pipe 70 Jointing Procedures (gutters) 65 Jointing Procedures (pipe) Leaves 57 Loose gutter or pipe - storage 64 Maintenance 64 Mastic asphalt roofing 76 Materials 77 Materials: Properties and Performance 63 Maximum Effective Roof rea [Table 1] 54 Multi-screw fixings 56 Page No Offset support 72 Offsets 58 60, 72 Outlet Connection Components [Table 7] 58 Physical attack 63 Pipe: - cutting 69 - joint design 69 - support centres 58, 72 - thermal expansion 69 - thermal movement 58 Pipe Jointing 70-82mm and 110mm Pipe 70 - ring-seal/push-fit jointing 70 - solvent weld jointing 70 Pipe Shoes 62,74 Pipe Support and Offsets 58, Pipe Support Centres [Tables 6 and 11] 58, 71 Push-fit jointing 70 Rafter rackets Rainwater daptor 73 Rainwater Diverter Kit 70 References 77 Ring-seal jointing 70 Rise-and-Fall rackets 67 Roof Outlets 63, 76 - uilt-up felt roofing 76 - Mastic asphalt roofing 76 Roof Outlet Capacity [Table 3] 55 Safety 64 Sealing Rings 77 Shallow Offsets 59 Shallow Offset Components [Table 8] 59 Side Rafter rackets 68 Snow loading 67 Solvent weld jointing 70 Special fabrication 77 Storage 64 Supply 77 Support centres 56, 58, 68 System Connections to elow Ground Drainage Thermal expansion 65, 69 Thermal movement 57, 58 Timber preservatives 63 Top Rafter rackets 68 Ultra violet light 63 Uneven surfaces 58 Universal Drain daptor CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

81 GENERL PVC-U RINWTER TECHNIQUES SYSTEMS Gutter lso vailable Jointingfrom Wavin Connects to 68mm circular downpipe Soil and Waste Product Data Soil OsmaSoil Ring-Seal System Offers a quick efficient solution, by means of a push fit joint Manufactured from PVC-U Simple to use Ideally suited for soil and ventilation systems vailable in 82, 110, and 160mm diameters Meets requirements of S EN :2000 and S 4514 vailable in lack, Grey, White and rown OsmaSoil Solvent Weld System Secure connection achieved via solvent cement application lternative method of jointing to the OsmaSoil Ring Seal systems Manufactured from PVC-U Ideally suited for soil and ventilation systems vailable in 110 & 160mm diameters Meets requirements of S EN :2000 and S 4514 vailable in lack, Grey, Olive, White and rown Waste OsmaWeld System Secure connection achieved via solvent cement application Comprehensive range of pipes, bends, tees, and adaptors Manufactured from crilonytrile utadiene Styrene (S) vailable in 32, 40, and 50mm diameters Meets requirements of S 5255 vailable in Grey and White Osma MUPVC Solvent Weld System Secure connection achieved via solvent cement application Comprehensive range of pipes, bends, tees, and adaptors Manufactured from Modified Unplasticized Polyvinyl Chloride (MUPVC) which has fire retardant properties vailable in 32, 40, and 50mm diameters Meets requirements of S 5255 vailable in lack, Olive, White, and rown Osma Push-Fit System Offers a quick efficient solution, by means of a push fit joint Comprehensive range of pipes, bends, tees, and adaptors Manufactured from Polypropylene (PP) vailable in 32, 40, and 50mm diameters Meets requirements of S EN :2000 vailable in lack, Grey, White and rown OSM RINWTER DRINGE SYSTEMS Design & Installation Guide 2004 SITEWORK General Index lso vailable from Wavin 81

82 Would you like more info? We would like to keep you updated about new products from Wavin Plastics Ltd. If you would like to receive additional literature or require to be removed from our database, please complete the form below. lternately all literature is available to download from ll valid records on the Wavin database are entered into a monthly draw for a case of wine. First Name Surname Job Title Company Name ddress Town/City Postcode County Phone Mobile Fax Please tick type of organisation (One only) I would like further information on: rchitect Irrigation Contractor OSM Rainwater systems uilder Cladder Client Organisation Civil Consulting Engineer Land Drainage Contractor Landfill & Waste Disposal Local uthority Major Construction Company OSM Soil & Waste systems OSM Flexible Plumbing systems OSM Underfloor Heating systems OSM elow Ground Drainage systems OSM Water Management systems Civil Contractor Multi-Utility Contractor OSM Pressure Pipe systems Design & uild M & E Contractor Environmental Consultant M & E Consulting Engineer Please return to: Gas Utility Contractor Plumber Groundworker Housing ssociation House uilder (under 20 units per annum) Housing Developer H & V Contractor Quantity Surveyor Roofer Utility Company Water Utility Contractor Wavin Plastics Ltd do not sell or provide data to other organisations for direct mail purposes. Wavin Plastics Limited Parsonage Way Chippenham Wiltshire SN15 5PN 82 CUSTOMER SERVICES TECHNICL ENQUIRIES TECHNICL FX EMIL info@wavin.co.uk

83 PVC-U RINWTER SYSTEMS Technical ssistance Further Information Technical dvice Contents and ssistance Further Information OSM Rainwater systems are backed by Wavin s comprehensive technical advisory service. This is available to provide expert assistance at every stage of a project, from planning and product selection to installation and maintenance. Services include: Full technical literature, including: - System Product Guides - Design and Installation Guides - Trade Price Lists ssistance with Rainwater systems product selection On site advice and troubleshooting Design and production of bespoke fittings to meet specific application requirements Contact Wavin Technical Design Department for prompt assistance: OSM RINWTER SYSTEMS The following related publications are available for OSM Rainwater systems: Product Guide Trade Price List Rainwater systems CD-Rom SSOCITED OSM SYSTEMS OSM systems are fully integrated to provide a total solution for above and below ground drainage, plumbing and heating. Contact Wavin Technical Design Department for further details regarding: OSM Soil & Waste systems OSM Flexible Plumbing systems OSM Underfloor Heating systems OSM elow Ground Drainage systems OSM Water Management systems OSM Pressure Pipes for Water TECHNICL DESIGN Tel: Fax: technical.design@wavin.co.uk To request a copy of any item(s) of current literature, please contact: LITERTURE REQUESTS Tel: Fax: literature@wavin.co.uk WVIN ONLINE The complete OSM product catalogue, together with design and installation guidance, is also available online at: ll literature can be downloaded via the searchable PDF library at Wavin images can be downloaded at different resolutions from PVC-U RINWTER SYSTEMS Data Card Technical ssistance Further Information 83

84 Rainwater Systems Product, Design and Installation Guide Meeting your needs OSM Rainwater systems, developed by Wavin Plastics Limited, forms part of a comprehensive range of plastic systems to provide intelligent solutions for all building, construction and utilities projects. These include: bove Ground Projects OSM Rainwater systems OSM Soil & Waste systems Plumbing & Heating Projects OSM Flexible Plumbing systems OSM Underfloor Heating systems elow Ground Projects OSM elow Ground Drainage systems OSM Water Management systems Pressure Pipe Projects OSM Pressure Pipes for Water ll OSM systems are backed by full technical literature and project support. See inside back cover for details. Water UK Partner Supporting information & learning in the water industry ISO 9001:2000 Wavin Plastics Limited operates a programme of continuous product development, and therefore reserves the right to modify or amend the specification of their products without notice. ll information in this publication is given in good faith, and believed to be correct at the time of going to press. However, no responsibility can be accepted for any errors, omissions or incorrect assumptions. Users should satisfy themselves that products are suitable for the purpose and application intended. Wavin Plastics Limited Parsonage Way Chippenham Wiltshire SN15 5PN Tel: Fax: info@wavin.co.uk RW109