SECTION ALUMINUM-FRAMED STOREFRONTS

Size: px

Start display at page:

Download "SECTION ALUMINUM-FRAMED STOREFRONTS"

Ursula French
6 years ago
Views:

1 SECTION ALUMINUM-FRAMED STOREFRONTS PART 1 GENERAL 1.1 SUMMARY A. Includes But Not Limited To 1. Furnish and install aluminum storefront entry system, including hardware, glazing, and calking, as described in Contract Documents. B. Related Sections 1. Electronic locking systems and cores for High Security Cylinders are excluded from Contract and provided by Owner in accordance with special services required under Section This specification establishes quality of materials and installation of those items for information of Contractor, Architect, and Owner's Representatives. 2. Division 07 - Quality of sealants 3. Sections Under Quality of glass and glazing 1.2 REFERENCES A. American Society For Testing And Materials 1. ASTM B , 'Standard Specification for Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles and Tubes 1.3 SUBMITTALS A. Product Data 1. Manufacturer's literature or cut sheets for storefront system and for each item of hardware. 2. Color and finish selections 3. Maintenance, adjustment, and repair instructions 4. Parts lists B. Shop Drawings 1. Show locations, sizes, etc, of hardware reinforcing. 1.4 QUALITY ASSURANCE A. Pre-Installation Conference - Schedule pre-installation conference for one week prior to scheduled installation of storefront system. 1.5 DELIVERY, STORAGE, AND HANDLING A. Deliver all parts of door, together with hardware, to Project at same time. 1.6 WARRANTY A. Closers - Provide Closer Manufacturer's standard warranty, 10 years minimum. PART 2 PRODUCTS 2.1 COMPONENTS Project Number 1 Section 08411

2 A. Manually Operated Doors 1. Aluminum T5 aluminum alloy, or meeting requirements of ASTM B 221, alloy GS 10A-T5 2. Stiles And Top Rails - 3-1/2 inches by 1-3/4 inches by inches thick nominal 3. Bottom Rail - 10 inches minimum by 1-3/4 inches by inches thick nominal 4. Construction - Manufacturer's standard. 5. Glazing Stops - Snap-in type with neoprene bulb-type glazing. Units shall be glazed from exterior side. 6. Weatherstripping - a. Neoprene bulb-type b. Approved Manufacturers And Models - 1) Kawneer - Sealair. 2) Vistawall - D Finish - a. Polyvinyledene Fluoride (PVF 2 ) Resin-base finish (Kynar or Hylar) containing 50 percent minimum PVF 2 in resin portion of formula and providing a pencil hardness of 3H. Thermo-cured two coat system consisting of corrosion inhibiting epoxy primer and top coat factory applied over properly pre-treated metal. b. Color white. 8. Approved Models - a. 350 Medium Stile by Kawneer b. Series 375 by Vistawall B. Frames 1. Aluminum T5 aluminum alloy or meeting requirements of ASTM B 221, alloy GS 10A-T5) 2. Mullion - Steel reinforced or heavy duty as necessary to prevent flexing of mullion. 3. Sills - Sidelight base to match height of door bottom rail. 4. Sealer Tape - 3M 5. Fasteners - Aluminum or non-magnetic stainless steel. Concealed fastenings shall be cadmium or zinc-plated steel. 6. Finish - Match doors 7. Frames shall be from same Manufacturer as doors. 8. Approved Systems - a. Single Glazed - 1) Trifab '450' by Kawneer 2) Series FG /4x4-1/2 by Vistawall b. Double Glazed - 1) Trifab '451' by Kawneer 2) Series FG3000 2x4-1/2 by Vistawall C. Glazing Characteristics 1. Interior Vestibule Glazing - Clear 2. Exterior Doors And Storefront Opening Into Foyers And Corridors - a. Clear interior pane and Clear exterior pane with Low E treatment on surface 2 D. VMR Manufacturers 1. Kawneer, West Valley City, UT Paul Cannon (801) FAX paul_cannon@kawneer.com 2. Vistawall, Terrell, TX Larry Garbert (800) ext 162 FAX lgarbert@vistawall.com 2.2 STOREFRONT HARDWARE A. Hinging - Top and bottom offset, ball bearing pivots per door leaf. B. Surface-Mounted Overhead Door Closers Project Number 2 Section 08411

3 1. Provide parallel arms on closers unless door position requires otherwise. 2. Closers shall allow for 180 degree opening and not be used as a stop. 3. Adjust closers to provide maximum opening force as required by governing code authority. 4. Closers shall have following features - a. Adjustable sweep speed b. Adjustable backcheck c. Non-handed, non-sized 5. Approved Models And Manufacturers - a. Surface mounted - 1) 4041 Series parallel arm by LCN 2) 7700 Series Parallel arm by Norton C. Exit Devices 1. Operation - a. Entry shall be by key. Device shall be locked by cylinder from outside. Key shall be removable when cylinder is in locked or unlocked position. b. Dogging operation shall be by accessible, permanent knob, but not by removable allen wrench devices. 2. Color - Equivalent to clear anodized. 3. Exterior Trim - Lever Handle or Pull equal to Kawneer CO-9 or Vistawall PH Types - a. Double Doors Without Mullions - Concealed vertical rods. b. All Other Doors - Rim Type. Provide type of strike that will allow installation of specified panic devices on storefront system specified. 5. Approved Manufacturers - a. Apex Series by Precision b. 80 Series by Sargent c. 98 or 99 Rim Series by Von Duprin D. Thresholds - Similar to Pemko 253 Profile E. Sweep Strips - Entrance Manufacturer's standard. F. Stops 1. Acceptable Models And Manufacturers - a. Floor Mounted - 1) FB19X by Glynn-Johnson 2) F9079X by Trimco / BBW / Quality 3) Equal as approved by Architect before installation. See Section b. Overhead - 1) DH5203 Series by Corbin Russwin 2) 90S Series by Glynn-Johnson 3) 590S Series by Sargent 4) Equal as approved by Architect before installation. See Section G. Push / Pulls 1. Kawneer CPII and CO-9, clear anodized 2. Vistawall PA16 and PH-12, clear anodized H. High Security Cylinders 1. Approved Manufacturer - a. Medeco accepting removable core with exclusive Church keyway at one door. I. Removable Cores (by Owner. Specification for information only) 1. Medeco cores with Level Six HUK-IC keying system with special Church keyway. a. Church And Factory Authorized Distributor - 1) Intermountain Lock & Supply Co, 3106 South Main, Salt Lake City, UT a) Utah - (800) b) Other - (800) c) FAX - (801) Project Number 3 Section 08411

4 J. Electronic Locking System (by Owner. Specification for information only) 1. Control Unit No. 5353EXT. 2. Rim Cylinder Keylok No with extension cable 3. System software with key reader and cabling. 4. Keys 5. Approved Manufacturer - a. Marlok Div of ILCO-UNICAN, Winston-Salem, NC (800) FABRICATION A. Construction shall meet Manufacturer's recommendations. Joints shall be tightly closed. B. Mortise in manner to give maximum hardware-door connection strength and neatness of appearance. Adequately reinforce with backplates or rivnuts to hold pivots and closers. PART 3 EXECUTION 3.1 VMR INSTALLERS A. Kawneer 1. Bountiful Glass Mollerup Glass Jones Paint & Glass B. Vistawall 1. Olympic Contract Glazing Weber Valley Glazing Altaview Glass INSTALLATION A. Interface With Other Work - When using overhead stops, coordinate installation with door closer and other door hardware. B. Accurately fit thresholds. Bed thresholds in specified sealant at contact points with floor and make watertight. C. Use sealer tape to prevent electrolytic action. D. Set plumb, square, level in correct alignment, and securely anchor. If used, line up horizontal rail in sidelight with door rail. E. Adjust doors for proper operation after glazing entry. Calk joints between frames and walls, both interior and exterior. 3.3 FIELD QUALITY CONTROL A. Site Tests - Pull test doors, especially pairs of single doors separated by permanent mullions, to ensure security of opening. 3.5 HARDWARE GROUP SCHEDULE A. Single Doors Group ST1 - Door No's 108B and 137A 1 each - Exit Device with trim, dogging capability, and prepped for locking cylinder Project Number 4 Section 08411

5 Group ST2 - Door No's 105A, 114B, and 143A Group ST3 - Door No's 108D and 137C 1 each - Push B. Double Doors Group ST5 - Door No 121A General Inactive leaf Active leaf and prepped for locking cylinder Group ST6 - Door No's 108A and 137B General Inactive leaf Active leaf Group ST7 - Door No's 108C, 121B, and 137D General Project Number 5 Section 08411

6 1 set - Threshold Inactive leaf 1 each - Push Active leaf 1 each - Push END OF SECTION Project Number 6 Section 08411

SECTION ALUMINUM WINDOWS

SECTION ALUMINUM WINDOWS SECTION 08520 ALUMINUM WINDOWS PART 1 - GENERAL 1.01 SUMMARY A. Section includes: 1. Storefront systems and aluminum framed glass doors. 2. Hardware, fasteners, accessories, filler pieces, etc., required