AcoustiFloat HI-SEP Floating Floor Specification (Canada)
|
|
- Marjorie Grant
- 6 years ago
- Views:
Transcription
1 February, 2009 Fabricated Sound and Vibration Control Assemblies Manufactured by WILREP LTD. [Project] SOUND & VIBRATION CONTROL FOR BUILDINGS AcoustiFloat HI-SEP Floating Floor Specification (Canada) This specification has been numbered, organized and formatted in accordance with the MasterFormat, Section Format and Page Format documents published jointly by Construction Specifications Canada (CSC) and Construction Specifications Institute (CSI). The content of this specification is of general order and must be adapted to the specific requirements of a project. It is offered as a guide to experienced and knowledgeable construction professionals who must assume full responsibility for its interpretation and use. Wilrep Ltd. is the material manufacturer. The square brackets [ ] containing texts indicate an option to be considered/inserted by the specifier. Remove brackets and unused options before printing. Part 1. General 1.01 SECTION INCLUDES A. Design, fabrication and installation of a floating floor sound control system specified herein from the structural building slab upwards, and generally as listed below: 1. Pre-engineered OSB (oriented strand board) subfloor panels complete with rubber isolators and fiberglass insulation. 2. Perimeter isolation board used to decouple the floating floor (subfloor panels and [concrete] wearing surface) from sidewalls and penetrations such as [piers,] [columns,] [pipes,] [floor drains,] [electrical appurtenances,] [and] [ ]. 3. Co-ordination of all mechanical and electrical requirements related to Work of this section. HI-SEP FLOATING FLOOR 1
2 1.02 RELATED REQUIREMENTS A. Structurally sound concrete substrate [Section ] B. Concrete wearing surface [Section ] C. Caulking [section ] SPEC NOTE: Include other type wearing surface or floor covering as required SUBMITTALS A. Submit the following in accordance with Section [ Submittal Procedures]:- 1. Shop Drawings: Provide shop drawings showing: A. Dimensioned Floor Layout. B. Layout of rubber isolators. C. Subfloor section details showing dead, live and concentrated loads, mechanical or electrical penetrations, and perimeter isolation details. 2. Acoustical Test Data from independent laboratory or acoustic engineering field test showing minimum STC-65 and a minimum IIC-75 using a 100 mm (4 ) floating floor, a 200 mm (8 ) or equivalent structural floor and a 38 mm (1-1/2 ) thickness fiberglass insulation filled subfloor. 3. Test and Evaluation Reports: Independent laboratory report indicating force/deflection characteristics of rubber isolators using an Instron 1350 Tension/Compression machine. 4. Product Data: Acoustic floating floor manufacturer s printed product literature and specifications. 5. Samples: Duplicate nominal 610 mm x 610 mm (24 x 24 ) samples of preengineered panels c/w rubber isolators and fiberglass insulation QUALITY ASSURANCE A. Manufacturer: to have minimum of 10 years experience with similar projects. B. Installer: to be manufacturer trained/authorized installer. C. Mock-up: Construct mock-up consisting of a minimum area of 2 panels x 2 panels, including perimeter isolation board. 1. Obtain [Consultant s] [Architect s] [Engineer s] approval of mock-up prior to proceeding with floating floor installation. HI-SEP FLOATING FLOOR 2
3 2. Erect mock-up as part of floating floor installation, leave in place after acceptance. 3. Approved mock-up to serve as standard of quality of finished installation DELIVERY, STORAGE AND HANDLING A. Deliver and store materials in original wrappings with manufacturer s seals and labels intact. Protect from damage and environmental conditions in accordance with manufacturer s recommendations. B. Neatly stack subfloor panels to prevent sagging. If panels must be removed from skids for ease of handling or temporary storage on-site prior to installation, stack panels exactly as they were received on the skids. If panels are numbered or tagged for their position in the floor system, keep separated to avoid installation confusion. C. Handle subfloor panels to prevent damage to edges or surfaces. Remove damaged or deteriorated materials from site ENVIRONMENTAL REQUIREMENTS A. Store subfloor panels in spaces where it is to be installed for 12 hours prior to installation. B. Store subfloor panels indoors protected from weather and moisture; do not install panels when wet. C. Ventilate building spaces as required to remove excess moisture. D. In cold weather, maintain continuous, uniform building temperatures of not less than 13 C (45 F) or more than 38 C (100 F) for a minimum period of 12 hours prior to, during, and following subfloor panel installation. Part 2. Products 2.01 ACCEPTABLE MANUFACTURER A. Floating floor system: AcoustiFloat HI-SEP Floating Subfloor Panel System manufactured by: Wilrep Ltd., 1515 Matheson Blvd. East, Unit C-10, Mississauga, Ontario L4W 2P5. Tel.: ; Toll Free: ; info@wilrep.com; Web: and B. Substitutions: Not permitted, however requests for substitutions will be considered providing substitute products and methods of execution are submitted at least 10 days prior to bid closing date. 3 HI-SEP FLOATING FLOOR
4 C. Accompany requests with evidence substantiating similarity in quality, including technical data sheet and formal 3-Part specifications MATERIALS A. Rubber Isolators: 50 mm (2 ) high; 50 mm (2 ) diameter Natural rubber to AASHTO and ASTM D2240, containing no fillers of any kind that would degrade performance or durability; cylindrical design with interior void to produce even deflection and low frequency performance, and integral ears for mechanical fastening to subfloor panels; 30 (AFHS-2-30) or 50 (AFHS-2-50) Durometer, as shown on the layout drawing[s]; SPEC NOTE: 50 Durometer (AFHS-2-50) isolators are recommended for extra heavy loads. Contact Wilrep Ltd. or AcoustiFloat representative for specification guidance. B. Rubber Isolator Mechanical Fasteners: 13 mm (1/2 ) staples. C. Insulation Board: 38 mm (1-1/2 ) thickness, 25.6 kg/m 3 (1.6 pcf) NRC.80 acoustical fiberglass insulation to CAN/ULC S102-M88, CGSB 51-GP-10M, and ASTM C-612, NFPA 90A and 90B, attached to entire underside of the subfloor panel board around rubber isolators. D. Insulation Fasteners: 13 mm (1/2 ) staples. E. Subfloor Panels: Nominal 610 mm x 610 mm (24 x 24 ), actual 590 mm x 590 mm (23-1/4 x 23-1/4 ) OSB (oriented strand board); 16 mm (5/8 ) thickness; T&G edges. Panel weight (with isolators and insulation) approx. 3.8 kg. (8.4 lbs.) F. Perimeter Isolation Board: closed cell polyethylene 13 mm (1/2 ) thickness x height to suit overall thickness of floating floor including 6 mm (1/4 ) and 10 mm (3/8 ) thickness for penetrations of pipes, conduits, etc. SPEC NOTE: If optional PVC perimeter venting is required, include the following statement in F. above: Factory pre-assemble 10 mm x 1220 mm (3/8 x 4-0 ) sections of fluted PVC vents to AF-PIB perimeter isolation board, to height as required and cap with subfloor manufacturer s standard dark brown precoated metal AF-VGF Vent Guard Flashing lapped 13 mm (1/2 ) at horizontal joints. G. Perimeter Caulking Compound: Non-hardening, non-drying, non-bleeding, caulking tube, trowel or pour grade; fire rated as required by local codes, Type. H. Floating Floor Drains: of type and size suitable for project and floating slab construction, isolated so as to have no rigid connection between the floating floor and building structure. I. Polyethylene Sheeting: Minimum 6 mil thickness. HI-SEP FLOATING FLOOR 4
5 2.03 DESIGN CRITERIA A. Provide acoustical isolation to prevent transmission of sound and vibration generated by [mechanical and electrical equipment] [or] [ ] to adjacent building areas. This requirement includes isolation of all items passing through the floating floor. B. Acoustically isolated floor to provide predictable system natural frequency for common concrete wearing surface of [9 Hz for 100 mm (4 )] [7.5 Hz for 150 mm (6 )] [6.5 Hz for 200 mm (8 )] thick floating slab. C. 15% maximum strain or 8 mm (.30 ) maximum deflection for [30 Durometer isolators under max. recommended load of 57 kg (125 lbs.)] [50 Durometer isolators under maximum recommended load of 79.4 kg (175 lbs.)]. D. Normal design load calculations for rubber isolators and layout to be based on the weight of the floating floor slab plus the weight of equipment, machines, fixtures and constructions supported by the floating floor plus 25% of the specified live load. E. Maximum design load calculations for rubber isolators and layout to be based on the weight of the floating slab plus the weight of the walls and fixtures supported by the floating slab plus 100% of the specified live load. F. Durability of rubber isolators to be 50 year minimum without significant degradation of performance. Part 3. Execution 3.01 EXAMINATION A. Before installation, examine alignment, smoothness and evenness of substrate. Notify [Contractor] in writing if substrate does not comply with requirements of acoustic subfloor manufacturer. If concrete structural slab is to be waterproofed or sealed, ensure coating is sufficiently cured prior to installation of panels. If coating remains tacky or exhibits excessive grip, cover with minimum 3 mil polyethylene sheeting to facilitate installation of the panels. Panels with attached isolators must be allowed to move freely when tapped into position. B. Verify items provided by other trades are properly installed. C. Commencement of work will imply acceptance of substrate conditions PREPARATION A. Ensure installation area is free of all debris, broom clean and dry. 5 HI-SEP FLOATING FLOOR
6 B. Brush or vacuum walls approximately 305 mm (12 ) up from structural floor to ensure walls are sufficiently clean to receive perimeter isolation board adhesive INSTALLATION A. General 1. Install acoustic floating floor strictly in accordance with manufacturer s printed instructions. 2. Co-ordinate work with related work to avoid rigid contact with the building. B. Perimeter Isolation Board 1. Install perimeter isolation board at sidewalls and around penetrations such as [piers,] [columns,] [pipes,] [drains,] [and] [electrical items] [ ]. 2. Ensure height of perimeter isolation board exceeds height from concrete structural substrate to top of concrete wearing surface by at least 50 mm (2 ). 3. Adhere perimeter isolation board using a single bead of good quality polyurethane based panel adhesive located at approximately the middle of the board. Press board firmly to wall and tape vertical joints including corner joints, and horizontally around acoustic subfloor/perimeter isolation board interface. Use construction sheathing tape or duct tape for isolation board joints at these locations and at penetrations. C. Acoustic Subfloor Panels 1. Following acoustic subfloor manufacturer s written instructions, install preengineered and prefabricated subfloor panels according to layout drawing[s]. If necessary, layout drawings may include specific locations in the system where certain tagged or labeled panels must be placed. These panels will be pre-fitted or allocated to be site-fitted with extra pick-up isolators for predetermined placement of heavy equipment or other point loads. 2. Using rubber mallet and/or spare piece of wood, tap panels into alignment, taking care not to damage panel edges. Make sure panels stay square and tight to adjacent panels. 3. Once panel is aligned, place 4 staples at each panel joint to help prevent panel misalignment using an air stapler to ensure staples are well seated and flush to surface of panels. HI-SEP FLOATING FLOOR 6
7 3.04 CLEANING 4. As the work progresses, ensure all factory installed point load rubber isolators are in place. If additional site installed pick-up isolators are required, staple isolator rubber ears to panel bottom or fasten with single screw and washer through the cylindrical void in isolator. Cut away fiberglass insulation to expose underside of panel prior to fastening isolator. 5. After panels are in place, install 3 mm (1/8 ) thick hardboard Perimeter Gap Seal Type AF-PGS at any location where subfloor panels are not in direct contact with perimeter isolation board. Finish by sealing seams with construction sheathing tape. 6. Cover OSB subfloor panels with minimum 6 mil polyethylene sheeting. Lap sheet edges minimum 75 mm (3 ) and tape watertight while ensuring application is free of wrinkles and fishmouths. 7. Place concrete wearing surface and reinforcement, including curing and finishing agents as specified in Division 3 of the specifications. Do not allow concrete [and] [rebar] to touch structure or base building. 8. When placing concrete, ensure concrete does not build up in one spot and overload subfloor panels. Spread each load over a dozen or so panels. Do not roll concrete carts directly over acoustic subfloor panels. Use temporary wood planking for heavy wheeled or concentrated loads. 9. After concrete has cured, use utility knife to cut excess perimeter isolation board at wall edges and penetrations. 10. If required by local codes, caulk top of perimeter isolation board. 11. Sound isolate drains. A. Upon completion of work, remove all materials, equipment and debris from site. B. Leave work area and adjacent surface in condition acceptable to [Consultant] [Architect] [Engineer]. C. Protect uncured concrete with markers, barriers or signs WASTE MANAGEMENT AND DISPOSAL A. Separate waste materials for [reuse] [and] [recycling] at nearest used building materials facility. B. Divert unused caulking, sealants and adhesive materials from landfill through disposal at hazardous materials depot. 7 HI-SEP FLOATING FLOOR
8 END OF SECTION AcoustiFloat Floating Floor Systems Manufactured by: WILREP LTD Matheson Blvd. East, Unit C-10 Mississauga, Ontario, Canada L4W 2P5 Tel.: (905) Fax: (905) Toll Free: Web: HI-SEP FLOATING FLOOR 8
1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards.
WOOD FLOORING GENERAL INFORMATION 1.1 This section applies to factory finished wood strip flooring. 1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards. 1.3
More informationACOUSTICAL WALL TREATMENT SECTION 09840
ACOUSTICAL WALL TREATMENT PART 1 GENERAL 1.1 SUMMARY A. Section Includes: Site-fabricated, stretched fabric acoustical wall system built with rigid polymer stretching system to secure fabric over the wall
More informationColphene BSW Training and Application Guide. Colphene BSW Waterproofing Membrane. 1. Prepare substrate
Colphene BSW Training and Application Guide Colphene BSW Waterproofing Membrane. 1. Prepare substrate Substrate must be structurally sound. Surface must be free of voids, spalled areas, loose aggregate,
More informationDIVISION 9 - SECTION QTscu Re-bonded Recycled Rubber Impact Sound Insulation Patent No. RE 41,945
Revised on 11/17/11. Supercedes all previous versions. Check website for updates. DIVISION 9 - SECTION 09 60 00.11 QTscu Re-bonded Recycled Rubber Impact Sound Insulation Patent No. RE 41,945 PART 1.0-
More informationSECTION MODIFIED BITUMINOUS SHEET WATERPROOFING
SECTION 07 13 52 MODIFIED BITUMINOUS SHEET WATERPROOFING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section
More informationE. Section Polymer Modified Cement Waterproofing. K. Section Sub drainage: Foundation perimeter drainage.
DELTA -DRAIN Section 07 10 00 Dampproofing and Waterproofing PART 1 GENERAL 1.1 SECTION INCLUDES A. Below grade drainage sheets. B. Plaza deck and planter drainage sheets. 1.2 RELATED SECTIONS A. Section
More informationEXCEL Medical Waste - Equipment Installation Section SECTION GYPSUM BOARD
SECTION 09 29 00 GYPSUM BOARD PART 1 - GENERAL 1.1 DESCRIPTION This section specifies installation and finishing of gypsum board. 1.2 RELATED WORK A. Installation of steel framing members for walls, partitions,
More informationSECTION mil thickness COLD FLUID-APPLIED WATERPROOFING
SECTION 07 14 16 CCW-MIRASEAL @ 120 mil thickness COLD FLUID-APPLIED WATERPROOFING PART 1 - GENERAL 1.1 SECTION INCLUDES: Installation of waterproofing membrane on surfaces indicated on drawings, consisting
More informationGenieMat FF. Floating Floor Systems for Airborne & Impact Sound and Vibration Isolation. It s not magic, it s engineering. Impact Sound Control
It s not magic, it s engineering. Impact Sound Control GenieMat FF Floating Floor Systems for Airborne & Impact Sound and Vibration Isolation Patents: US 8240430, US8556029, CA 2500956, CA 2503420 GenieMat
More informationFloor Insulation Underlayment Section Sound Control Matting
Floor Insulation Underlayment Section 09618 Sound Control Matting Part I General 1.1 Summary A. Section includes a sound control material for achieving an STC and IIC rating in excess of 50 to meet building
More informationENKASONIC FLOOR UNDERLAYMENT 9110
ENKASONIC FLOOR UNDERLAYMENT 9110 GS1197 Section 13080 SECTION 09618 SOUND CONTROL MATTING Part I General 1.1 Summary A. Section includes a sound control material for achieving an STC and IIC rating in
More informationPLATON RUGGED, DIMPLED HIGH-DENSITY POLYETHYLENE (HDPE) MEMBRANE THAT KEEPS FOUNDATIONS AND FLOORING DRY ADVANCED TECHNOLOGY EASY INSTALLATION
DRAINAGE SOLUTIONS SINCE 1908 PLATON RUGGED, DIMPLED HIGH-DENSITY POLYETHYLENE (HDPE) MEMBRANE THAT KEEPS FOUNDATIONS AND FLOORING DRY ADVANCED TECHNOLOGY EASY INSTALLATION PROVEN PERFORMANCE ARMTEC.COM
More informationSECTION PRE-ENGINEERED BUILDING INSULATION
PART 1 GENERAL SECTION 07213 PRE-ENGINEERED BUILDING INSULATION Microsoft Word Instructions: Display hidden notes to specifier by using "Tools"/"Options"/"View"/"Hidden Text". 1.1 SECTION INCLUDES A. Pre-Engineered
More informationSECTION RESILIENT SHEET FLOORING
SECTION 09 65 16 RESILIENT SHEET FLOORING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1.
More informationSECTION COLD APPLIED RUBBER MODIFIED ASPHALT WATERPROOFING
P.O. Box 599 - Mars, PA 16046 800-321-3337 SECTION 07555 COLD APPLIED RUBBER MODIFIED ASPHALT WATERPROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including
More informationARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE
ARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE MANNINGTON COLORFIELDS SHEET RUBBER FLOORING Section 09 65 16 Sheet rubber Flooring (Thermoset Rubber) Created May 2012 Mannington Mills, Inc. P. O. Box
More informationSECTION GYPSUM BOARD ASSEMBLIES
SECTION 09 21 16 GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.1 SECTION INCLUDES A. Metal stud wall and ceiling framing, 20 gauge. B. Metal channel suspended ceiling framing. C. Gypsum board. D. Gypsum sheathing.
More informationNOVABRIK MORTARLESS CONCRETE BRICK VENEER SPECIFICATION. MASTERFORMAT SECTION (Mortarless Concrete Brick Veneer)
NOVABRIK MORTARLESS CONCRETE BRICK VENEER SPECIFICATION MASTERFORMAT SECTION 04818 (Mortarless Concrete Brick Veneer) Spec_USA_En_18102005.doc 12/1/2005 Novabrik Page 2 Section 04818 NOVABRIK MORTARLESS
More informationSECTION RADIATION SHIELDING ENCLOSURE Low Intensity Radiation Protection
SECTION 13090 RADIATION SHIELDING ENCLOSURE Low Intensity Radiation Protection Prepared by: 90 Dayton Avenue, Unit 4B, Suite 13 Passaic, NJ 07055 (973) 574-9077 13090-1 LOW INTENSITY RADIATION PROTECTION
More informationSECTION A. ACSE 7 Minimum Loads for Buildings and other Structures.
SECTION 06 12 00 STRUCTURAL INSULATED PANELS ------------------------------------------------------------------------------------------------------------ PART 1- GENERAL ----------------------------- 1.1
More informationSLAB ON GRADE Insul-Joint or Expansion Joint Material as Required by A/E Specifications AquaCheck Liquid Coating 400 (Waterproofing Membrane) with Aqu
INSTALLATION INSTRUCTIONS Note: The following installation instructions are based off of ASTM E 1643 (Standard Practice for Installation of Water Vapor Retarders Used in Contact with Earth or Granular
More informationA. Product Data: Submit manufacturer s product data, with complete general and specific installation instructions, recommendations, and limitations.
SECTION 071700 - BENTONITE WATERPROOFING PART 1 - GENERAL 1.1 WORK SUMMARY A. The work of this section includes, but is not limited to the furnishing and installing the following materials, per project
More informationRecommended Design Considerations. and. Guide Specifications For. Commercial Building Insulation
Recommended Design Considerations and Guide Specifications For Commercial Building Insulation Date of Issue: October 1, 2004 Recommended Design Considerations and Guide Specifications For Commercial Building
More informationTTR SYSTEMS ROOF SPECIFICATION
SECTION 07 53 24 EPDM roofing membrane applied over spray applied polyurethane foam TTR SYSTEMS ROOF SPECIFICATION This specification has been numbered, organized and formatted in accordance with the Master
More informationStandard specification for the application of Danosa Two-Layer waterproof roofing membrane to plywood & concrete surfaces.
Standard specification for the application of Danosa Two-Layer waterproof roofing membrane to plywood & concrete surfaces. BRANZ Appraised No. 678 Ref: P3200 Rev 1 February 2016 Page 1 of 5 1.0 PREAMBLE:
More informationby Rollfab Metal Products
by Rollfab Metal Products SECTION 07460 ALUMINUM SIDING AND SOFFITS PART 1 GENERAL 1.2 RELATED SECTIONS 1.3 REFERENCES A. SECTION INCLUDES B. Aluminum Siding. C. Aluminum Soffits. D. Aluminum trim and
More informationSECTION 07530CP EPDM MEMBRANE ROOFING
PART 1 GENERAL 1.1 SUMMARY SECTION 07530CP EPDM MEMBRANE ROOFING A. Section includes: 1. Adhered membrane roofing and flashing 2. Mechanically fastened roof insulation 3. Walkway pads 1.2 ARCHITECTURAL
More informationMASTERFORMAT SPECIFICATION
Contact: PFB Manufacturing, LLC Insulspan SIP Plant 9012 East US 223 Blissfield, MI, USA 49228-0026 Phone: 800.726.3510 Plasti-Fab Ltd. Head Office 100, 2886 Sunridge Way N.E. Calgary, AB Canada, T1Y 7H9
More informationA. ASTM C190 - Test Method for Tensile Strength of Hydraulic Cement Mortars
SECTION 04850 (04 40 00) MSI PRECAST STONE VENEER SYSTEM PART 1 GENERAL 1.1 SECTION INCLUDES A. MSI Precast Stone Veneer for exterior and interior vertical surfaces. 1.2 RELATED SECTIONS Specifier Notes:
More informationSECTION CEMENT BOARD SUPPORTED ADHERED MASONRY VENEER. 2. Installation materials including adhesives, mortars, and pointing mortars.
(Specifier Note: The purpose of this guide specification is to assist the Specifier in correctly specifying cement board supported adhered masonry. The Specifier needs to edit these guide specifications
More informationSECTION HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT. A. ASME B31.1 (American Society of Mechanical Engineers) - Power Piping
SECTION 22 05 29 HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 SUMMARY A. Section includes pipe and equipment supports, hangers, anchors, bases sleeves and the sealing of
More informationDIVISION: FINISHES SECTION: ACOUSTIC TREATMENT REPORT HOLDER: ECORE INTERNATIONAL, INC.
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1522 Reissued 09/2016 This report is subject to renewal 09/2018. DIVISION: 09 00
More informationA. Submit product data sheets and literature verifying physical properties of materials.
I. GENERAL ACRYSHIELD ROOF MANAGEMENT SYSTEM Installation Guide Specification For Preserving EPDM Roofs 07500 Saving Money, Safeguarding the Environment One Roof at a Time. 1.01 SUMMARY A. Provide labor,
More informationB. American Society for Testing and Materials: 1. ASTM F708 - Standard Practice for Design and Installation of Rigid Pipe Hangers.
SECTION 230529 - HANGERS AND SUPPORTS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Pipe hangers and supports. 2. Hanger rods. 3. Inserts. 4. Flashing. 5. Sleeves. 6. Mechanical sleeve seals. 7. Firestopping
More informationProudly Made in the U.S.A.
5-Year Warranty Proudly Made in the U.S.A. Cast-In-Place (wet-set) 2 Cast-In-Place (wet-set) Tactile Proudly Made in the U.S.A. In stock colors White 37875 Brick Red 20109 Yellow 33538 Blue 15187 Safety
More informationDIVISION 13 - SPECIAL CONSTRUCTION SECTION ACOUSTICAL PANEL ENCLOSURE
DIVISION 13 - SPECIAL CONSTRUCTION SECTION 13080 - ACOUSTICAL PANEL ENCLOSURE 1 GENERAL 1.01 SUMMARY A. ACOUSTIC ENCLOSURE CONSISTING OF WALLS, CEILING, STRUCTURAL FRAMING, CONNECTING MEMBERS, DOORS, WINDOWS,
More informationSECTION THERMOPLASTIC POLYOLEFIN (TPO) ROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 075423 - THERMOPLASTIC POLYOLEFIN (TPO) ROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including Division 00 Bidding Requirements and other Division
More informationThe GlasRoc Shaftliner Type X advantage...
C e r t a i n T e e d SHAFTLINER F o r A r e a S e p a r a t i o n F i r e w a l l s Shaftliner S Type X for Area Separation GlasRoc Shaftliner is a specially formulated product for applications where
More informationProduct Guide Specification
PAC International, Inc. December 2007 Las Vegas, NV 89128 Toll Free (866) RSIC-100 (866) 774-2100 Fax (866) 649-2710 Web Site www.pac-intl.com E-Mail info@pac-intl.com Product Guide Specification Specifier
More informationSECTION ORNAMENTAL ALUMINUM RAILING. ** NOTE TO SPECIFIER ** Superior Aluminum Products, Inc.; Ornamental aluminum railing products.
SECTION 05720 ORNAMENTAL ALUMINUM RAILING ** NOTE TO SPECIFIER ** Superior Aluminum Products, Inc.; Ornamental aluminum railing products. This section is based on the products of Superior Aluminum Products,
More informationINFINITY MAX TILE SPECIFICATION
www.infinityperformance.com 888-479-1017 INFINITY MAX TILE SPECIFICATION Physical Specification: INFINITY MAX configurations consist of an interlocking, dual durometer flooring system consisting of a high
More informationEverlast Basic Rolls and Tiles GUIDE SPECIFICATIONS Ecore
August 15 th, 2016 - This document is provided solely as a convenience for spec writers in the drafting process. Ecore will not be held responsible for the use or alteration of any information contained
More informationSECTION and/or Resilient Sheet Flooring and/or Resilient Tile Flooring
Specifier Note: the following CSI (Construction Specifications Institute) section describes the resilient flooring system to be installed on the specific project. The number and title of the section may
More informationALL-ALUMINUM DOOR & WINDOW FRAMING
ALL-ALUMINUM DOOR & WINDOW FRAMING WITH INTEGRATED ALUMINUM DOOR STOP SECTION 08 41 13 ALUMINUM FRAMED ENTRANCES AND STOREFRONTS SPECIFICATION PART 1 GENERAL 1.1 SECTION INCLUDES: A. Prefinished aluminum
More informationRegupol AktivPro RESILIENT ATHLETIC SURFACING REGUPOL RECYCLED RUBBER MOLDED TILES
Regupol AktivPro RESILIENT ATHLETIC SURFACING REGUPOL RECYCLED RUBBER MOLDED TILES PART 1.0 GENERAL 1.1 SECTION INCLUDES A. Resilient Flooring, including recycled rubber flooring. 1. AktivPro Recycled
More informationHACKER SOUND MAT II, to create a quieter living environment while meeting demanding project specifications in multi-family construction.
HACKER SOUND MAT II HACKER SOUND MAT II, to create a quieter living environment while meeting demanding project specifications in multi-family construction. HACKER SOUND MAT II, a recycled rubber sound
More informationSECTION PREFINISHED ENGINEERED WIDE-PLANK FSC OAK FLOORING
General notes to the specifier: SECTION 09 64 29 PREFINISHED ENGINEERED WIDE-PLANK FSC OAK FLOORING This is a template: edit this specification carefully to suit specific project requirements. Following
More informationLUX Specifications. Section S - Preformed Steel Siding
Part 1 General.1 System-1: Installation over building paper or air barrier membrane, on exterior grade gypsum board or exterior grade wood sheathing. 1.2 RELATED SECTIONS.1 Section 01 11 00 Summary of
More informationSECTION STAY-IN-PLACE INSULATED CONCRETE FORMING SYSTEM
ARCHITECTURAL SPECIFICATIONS MANUFACTURER: InterBlock LLC PO Box 1123, Sheboygan, WI 53082 Phone Number 920-207-7234 SECTION 03100 STAY-IN-PLACE INSULATED CONCRETE FORMING SYSTEM PART 1 GENERAL 1.01 Summary
More informationSignature Sports Flooring Installation Instructions. For SignaDeck Premium Rubber Tiles
Signature Sports Flooring Installation Instructions For SignaDeck Premium Rubber Tiles These instructions supersede any verbal or written instructions from Signature Sports Flooring representatives and
More informationGYPSUM BOARD SECTION GYPSUM BOARD PART 1 - GENERAL
13686.00 GYPSUM BOARD 092116-1 1.1 RELATED DOCUMENTS: SECTION 092116 - GYPSUM BOARD PART 1 - GENERAL A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division
More information***************************************************************************************************************
09330 QUARRY TILE *************************************************************************************************************** SPECIFIER: CSI MasterFormat 2004 number 09 30 16 ***************************************************************************************************************
More informationMay 8, 2017 ADDENDUM #1. IFB Resin Floor System For Highway Department Central District Building
May 8, 2017 ADDENDUM #1 IFB 17-082 Resin Floor System For Highway Department Central District Building Addendum #1 is being issued to offer an alternate resin flooring system. 096700 FLUID-APPLIED FLOORING
More informationSECTION SHEET MEMBRANE SOUND REDUCTION, CRACK ISOLATION / JOINT BRIDGING, AND WATERPROOFING
SECTION 093000 - SHEET MEMBRANE SOUND REDUCTION, CRACK ISOLATION / JOINT BRIDGING, AND WATERPROOFING PART 1 - GENERAL This specification includes the sheet membrane used for sound reduction, crack isolation
More informationSECTION and/or Resilient Sheet Flooring and/or Resilient Tile Flooring
Specifier Note: the following CSI (Construction Specifications Institute) section describes the resilient flooring system to be installed on the specific project. The number and title of the section may
More information.1 Provide submittals in accordance with Section Submittal Procedures.
Place D Orléans Transitway Section 07 13 52 1231 Place D Orléans Dr, Ottawa, ON. WATERPROOFING MEMBRANE City of Ottawa Project No. CR008042 Page 1 of 2 1 GENERAL 1.01 SUBMITTALS.1 Provide submittals in
More informationApplication Instructions for Dryvit Backstop NT For Use Beneath Claddings Other Than Dryvit EIFS
Application Instructions for Dryvit Backstop NT For Use Beneath Claddings Other Than Dryvit EIFS CHECKLIST PRIOR TO THE INSTALLATION OF BACKSTOP NT - SMOOTH AND TEXTURE Project Conditions Maximum storage
More informationNATIONAL GYPSUM COMPANY Wood Frame Walls And Ceilings Single- And Double-Layer Construction
Walls And Ceilings Single- And Double-Layer Construction 09 9 00/NGC Single-Layer Construction The single-layer construction system consists of a single layer of Gold Bond brand Gypsum Board applied to
More information1. Decks, balconies, and sun porches 2. Walkways, ramps, and stairways 3. Patios and courtyards
SECTION 07185 TRAFFIC MEMBRANE PART 1 GENERAL 1.1 SECTION INCLUDES A. Traffic membrane, consisting of welded seam PVC waterproofing, over f following surfaces: 1. Decks, balconies, and sun porches 2. Walkways,
More informationSECTION HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT
SECTION 23 05 29 HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 SUMMARY A. Section includes pipe and equipment supports, hangers, anchors, bases sleeves and the sealing of work
More informationSection HIGH-TENSION Stretched-Fabric Wall Systems SoftWalls, Inc.
P a g e 1 PART I. GENERAL 1.01 Scope A. Furnish and install SoftWalls HIGH-TENSION Acoustical & Tackable Stretch Fabric Systems B. Related Work Specified Elsewhere: 1.Preparation of a smooth, flat and
More informationA. Source Limitations: Obtain each type of building insulation through one source.
SECTION 07210 - BUILDING INSULATION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationCOMPOSITE (WPC) ENGINEERED VINYL FLOORING INSTALLATION
COMPOSITE (WPC) ENGINEERED VINYL FLOORING INSTALLATION PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE YOU BEGIN INSTALLATION! IMPROPER INSTALLATION WILL VOID WARRANTY. STOP! WPC Engineered Vinyl Flooring
More informationWhen I started tiling, we didn t do our own shower pans that BATHS
BATHS Preventing Leaks in Tiled Showers Detail the pan properly before any tile is installed BY TOM MEEHAN Photos by Roe Osborn When I started tiling, we didn t do our own shower pans that job fell to
More informationTILE TILE
09300 - TILE 09300-1 PART ONE: GENERAL 1.1 Description TILE 1.1.1 Work of this Section, as shown or specified, shall be provided by the Interior Contractor and shall be in accordance with the requirements
More information1.3 Work shall include all reinforcement and accessories necessary to complete installation.
CERAMIC TILING GENERAL INFORMATION 1.1 Ceramic mosaic tile floors and bases, glazed wall tile wainscots and walls, and marble thresholds. 1.2 Installation will typically be with latex-portland cement mortar
More informationSTEP UP SHOWER BASE INSTALLATION GUIDE FOR TIMBER AND CONCRETE FLOORS
GUIDE FOR TIMBER AND CONCRETE FLOORS EDITION: APRIL 2016 IMPORTANT: This guide is for the installation of a Step Up shower base on a timber or concrete floor. If you require a walk in (flush with floor)
More informationSPECIFICATION GUIDELINE
SPECIFICATION GUIDELINE Environmental Stoneworks Corporate Office 6300 East Stapleton Drive South Denver, CO 80216 Phone (303) 309-3040 Fax (303) 309-3059 www.estoneworks.com Environmental Stoneworks specification
More informationAssembly Instruction. wedi Fundo Primo Shower System
Assembly Instruction wedi Fundo Primo Shower System Assembly Instructions wedi Fundo wedi Fundo Shower System-Primo Overview & General Product Description of the wedi Fundo Shower Systems All wedi Waterproof
More informationB. Store products in dry spaces protected from the weather, with ambient temperatures maintained between 50 and 90 deg F (10 and 32 deg C).
SECTION 09651 - RESILIENT TILE FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSECTION WOOD GYMNASIUM FLOORING
HORNER SAFE 2 SYSTEM Page 1 of 3 SECTION 096466 --- WOOD GYMNASIUM FLOORING PART 1-GENERAL 1.1 DESCRIPTION A. This document specifies a wood strip athletic floor system consisting, in general, of wood
More informationAssembly Instruction. wedi Fundo Primo Steam Shower System
Assembly Instruction wedi Fundo Primo Steam Shower System Assembly Instructions wedi Fundo wedi Fundo Steam Shower System Residential and Commercial Use Whether installed in a steam room with commercial
More informationLouis Armstrong New Orleans International Airport NOAB Project # North Terminal Development Program Phase 1
Louis Armstrong New Orleans International Airport NOAB Project # 8910-01233 PART 1 - GENERAL SECTION 07 71 29 - MANUFACTURED ROOF EXPANSION JOINTS 1.1 RELATED DOCUMENTS A. Drawings and general provisions
More informationSECTION HVAC INSULATION
PART 1 GENERAL 1.1 SUMMARY SECTION 23 07 00 HVAC INSULATION A. Section Includes: 1. Ductwork insulation. 2. Duct liner. 3. Insulation jackets. 4. Equipment insulation 5. Piping system insulation. 6. Insulation
More informationSECTION DECORATIVE STAINLESS STEEL DRAINS AND GRATES
PART 1 - GENERAL 1.1 SUMMARY: SECTION 05 70 00 MODERN DESIGN LINEAR DRAINS DECORATIVE STAINLESS STEEL DRAINS AND GRATES EDITING NOTE: DELETE SYSTEMS AND MATERIALS THAT ARE NOT REQUIRED FOR THE PROJECT.
More informationInstallation Guide Wall Panels
Installation Guide Wall Panels Jointless or Dry-Stacked Installation (Read Prior to installation) The MStone system is a jointless / dry-stacked installation where panels and corners fit tightly together
More informationITEM 458 WATERPROOFING FOR STRUCTURES
ITEM 458 WATERPROOFING FOR STRUCTURES 458.1. Description. This Item shall govern for the furnishing and placing of waterproofing on concrete and steel bridge decks of railroad structures and on other structures
More informationEcore Athletic Stacked Performance Collection Rolls and Interlocking Tiles GUIDE SPECIFICATIONS Ecore
September 22 nd, 2015 - This document is provided solely as a convenience for spec writers in the drafting process. Ecore will not be held responsible for the use or alteration of any information contained
More informationRMF Intercell. NBS Specification 2013 K41
RMF Intercell NBS Specification 2013 K41 InterfaceFLOR BV. K41 Specification 40mm, 60mm, 80mm, 90mm and 110mm K41 Raised access floors To be read with Preliminaries/ General conditions. TYPES OF RAISED
More informationSPECIFICATIONS FOR AluSystems Aluminum Composite Panels Series 20 Dry Joint 1.00 GENERAL 1.01 RANGE OF WORK Section includes: Laminated panels and attachment systems for use as exterior cladding. A. Provide
More informationEcore Athletic Elevate BOUNCE 2 GUIDE SPECIFICATIONS Ecore
October 31st, 2016-This document is provided solely as a convenience for spec writers in the drafting process. Ecore will not be held responsible for the use or alteration of any information contained
More informationDSC BUILDING 1200 ALTERATIONS OCTOBER 2011 SECTION DUCT INSULATION
SECTION 230713 DUCT INSULATION PART 1 GENERAL 1.1 SUMMARY A. Related Sections: 1. 233113 Ductwork and Accessories 1.2 REFERENCES A. American Society for Testing and Materials (ASTM): 1. E84-96a Test Method
More informationGUIDE SPECIFICATION
GUIDE SPECIFICATION 09 64 33.01 940 Centre Circle, Suite 1000 Altamonte Springs, FL 32714 Telephone: 407-260-9910 Fax: 407-260-9933 Toll Free: 800-800-5247 Web Site: http://www.kahrs.com This Guide Specification
More informationSECTION WOOD AND ATHLETIC FLOORING. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.
SECTION 096466 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting
More informationHARO SPORTS FLOOR C.S.I. GUIDE SPECIFICATION Helsinki-Gymnasium Floor System 10/2010 SECTION WOOD ATHLETIC FLOORING
HARO SPORTS FLOOR C.S.I. GUIDE SPECIFICATION Helsinki-Gymnasium Floor System 10/2010 SECTION 09 64 66 WOOD ATHLETIC FLOORING PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Wood athletic flooring including
More informationSpecifications for FL-100 Soffit Panel
Union Corrugating Company Specifications for FL-100 Soffit Panel SECTION 07410 METAL SOFFIT PANELS PART 1 GENERAL 1.1 DESCRIPTON A. Section Includes: 1. Preformed metal soffit panel system 2. Associated
More informationSECTION ORNAMENTAL ALUMINUM RAILING. ** NOTE TO SPECIFIER ** Superior Aluminum Products, Inc.; Ornamental aluminum railing products.
SECTION 05720 ORNAMENTAL ALUMINUM RAILING ** NOTE TO SPECIFIER ** Superior Aluminum Products, Inc.; Ornamental aluminum railing products. This section is based on the products of Superior Aluminum Products,
More informationIndustry Standard Terms & Definitions Of The Steel Deck Institute
Industry Standard Terms & Definitions Of The Steel Deck Institute A specialized set of jargon to describe common terms used by manufacturers and other professionals associated with the usage of Steel Deck
More informationBioPrism Solid Surface
Please read all instructions before installing products. STORAGE & HANDLING: Check for damage that may have occurred during transit. Keep receptor flat on pallet, as it was shipped, until ready to install.
More informationRAISED ACCESS FLOOR SYSTEM TECHNICAL SPECIFICATION
RAISED ACCESS FLOOR SYSTEM TECHNICAL SPECIFICATION PROVISIONAL BILL OF QUANTITIES RAISED ACCESS FLOOR SYSTEM TECHNICAL SPECIFICATION 1 RAISED ACCESS FLOOR SPECIFICATION SYSTEM DESCRIPTION This specification
More informationSuggested Specification for Tri-Patch Versatile Concrete Patching Compound
Suggested Specification for Tri-Patch Versatile Concrete Patching Compound SURFACE PREPARATION for Interior and Exterior Floor-Covering Installations. (Vinyl Composition Tiles, Sheet Vinyl, Rubber, Indoor
More informationUNDERLAYMENT INSTALLATION INSTRUCTIONS
UNDERLAYMENT INSTALLATION INSTRUCTIONS Table of Contents BASE PREPARATION I. General Information... 3 II. Job Site Conditions... 3 III. Subfloor Requirements & Preparation...3 IV. Hazards... 4 V. Material
More informationPERM-FLEX ASSEMBLY DIRECT APPLICATION TO CEMENTITIOUS SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960
STUC-O-FLEX PERM-FLEX ASSEMBLY DIRECT APPLICATION TO CEMENTITIOUS SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960 PART 1 - GENERAL 1.01 DESCRIPTION Provide all labor, materials and equipment necessary
More informationEclipse Energy Guard. Product Information & Installation Manual General Installation Requirements
Product Information & Installation Manual 01 Important Notice to Buyers and Users of RoyOMartin wall system These instructions are not intended to cover every installation requirement, application, detail
More informationERSYSTEM ONESTEP PLUS
1 DG0047-A 05/2017 AGED (EPDM, TPO, CSPE-HYPALON, PIB) SINGLE-PLY (THERMOSET) MEMBRANE RESTORATION SYSTEM APPLICATION SAMPLE DESIGN GUIDELINE ERSYSTEM ONESTEP PLUS ITW POLYMERS SEALANTS NORTH AMERICA,
More informationSECTION ATHLETIC AND RECREATIONAL SURFACING. A. ASTM C 67 - Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile.
SECTION 02790 ATHLETIC AND RECREATIONAL SURFACING PART 1 GENERAL 1.1 SECTION INCLUDES A. Resilient interlocking fitness flooring. 1.2 RELATED SECTIONS 1.3 REFERENCES A. ASTM C 67 - Standard Test Methods
More informationSECTION PREFINISHED FSC MAPLE FLOORING. This is a template: edit this specification carefully to suit specific project requirements.
SECTION 09 64 29 PREFINISHED FSC MAPLE FLOORING General notes to the specifier: This is a template: edit this specification carefully to suit specific project requirements. Following guidelines established
More informationFLUID APPLIED WATERPROOFING
SECTION 07120 FLUID APPLIED WATERPROOFING PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03300 - Cast-In-Place Concrete. 2. 09200 - Metal Studs, Metal Lath, Suspension Ceilings, Plaster, and Stucco.
More information