HOLD DOWN CLIPS #WGACHD LIFT & SHIFT CLIPS #WGACLNS [19.05] 3/4" 1/4" [6.35]TYP. REVEAL HOLD DOWN CLIP (BY OTHERS) FASTENERS LIFT & SHIFT

Transcription

1 SAFETY CLIPS 5/6" H.D. T-GRID #8x5/8" OR PANHEAD SCREWS SAFETY CLIP 3" = '-0" [6.35] TYP. REVEAL LIFT & SHIFT SYSTEM SECTION [9.05] [6.35]TYP. REVEAL SAFETY CLIP 6" = '-0" HOLD DOWN CLIP LIFT & SHIFT CLIP 3 HOLD DOWN CLIP 6" = '-0" 4 LIFT & SHIFT CLIP 6" = '-0" NOTES: 5/6" H.D. T-GRID ALL CLIPS AND PANEL SCREWS PROVIDED BY ACOUSTIGREEN AND INSTALLED BY OTHERS. PANELS FOR 9/6" T-GRID NOT AVAILABLE. WOOD PANEL LIFT & SHIFT CLIPS 5 LIFT & SHIFT PANEL REMOVAL 3" = '-0" LIFT & SHIFT CEILING PANEL SYSTEM DRAFTED BY: YN/BCO LAST REVISED: 5/3/6 AS NOTED

2 NOTE: HOLES ARE PRE DRILLED FOR LIFT & SHIFT CLIPS AND FOR SAFETY CLIPS. LIFT & SHIFT PANELS ARE LIMITED TO 4" WIDTH. x CLG. PANELS 5/6" H.D. T-GRID SAFETY CLIPS HOLD DOWN CLIPS BACK OF X PANELS /" = '-0" 4" TAP FOR #8x5/8" SCREW (TYP.) 35/64" 4" " BACK OF PANEL 5/6" [33.53] TYP. [9.0] TYP. LIFT & SHIFT X PANEL TAP /" = '-0" LIFT & SHIFT X PANELS DRAFTED BY: YN/BCO LAST REVISED: 5/4/6 AS NOTED

3 NOTE: HOLES ARE PRE DRILLED FOR LIFT & SHIFT CLIPS AND FOR SAFETY CLIPS. LIFT & SHIFT PANELS ARE LIMITED TO 4" WIDTH. x4 CLG. PANELS (6) PER PANEL 5/6" H.D. T-GRID SAFETY CLIPS BACK OF X4 PANELS /" = '-0" 48" 35/64" TAP FOR #8x5/8" SCREW (TYP.) 5/6" [33.53] TYP. 4" BACK OF PANEL LIFT & SHIFT X4 PANEL TAP /" = '-0" [9.0] TYP. LIFT & SHIFT X4 PANELS DRAFTED BY: YN/BCO LAST REVISED: 5/4/6 AS NOTED

4 x6 CLG. PANELS NOTE: HOLES ARE PRE DRILLED FOR LIFT & SHIFT CLIPS AND FOR SAFETY CLIPS. LIFT & SHIFT PANELS ARE LIMITED TO 4" WIDTH. (8) PER PANEL 5/6" H.D. T-GRID SAFETY CLIPS BACK OF X6 PANELS /" = '-0" 7" 4" 35/64" TAP FOR #8x5/8" SCREW (TYP.) BACK OF PANEL 5/6" [33.53] TYP. 35/64" " = '-0" 4" O.C. MAX. LIFT & SHIFT X6 PANEL TAP [9.0] TYP. LIFT & SHIFT X6 PANELS DRAFTED BY: YN/BCO LAST REVISED: 5/4/6 AS NOTED

5 5/6" H.D. T-GRID NOTE: HOLES ARE PRE DRILLED FOR LIFT & SHIFT CLIPS AND FOR SAFETY CLIPS. LIFT & SHIFT PANELS ARE LIMITED TO 4" WIDTH. (8) PER PANEL SAFETY CLIPS x8 CLG. PANELS BACK OF X8 PANELS " = '-0" 96" 4" O.C. TYP. 4" O.C. TYP. 4" TAP FOR #8x5/8" SCREW (TYP.) BACK OF PANEL 5/6" [33.53] TYP. LIFT & SHIFT X8 PANEL TAP = '-0" 35/64" [9.0] TYP. LIFT & SHIFT X8 PANELS DRAFTED BY: YN/BCO LAST REVISED: 5/4/6 AS NOTED

6 NOTES: VERTICAL RETURN FOR HEAVY DUTY APPLICATION ONLY ALL CLIPS AND PANEL SCREWS PROVIDED BY ACOUSTIGREEN AND INSTALLED BY OTHER FIELD CUT MITER CORNER, JOINT GLUED OR PINNED IN FIELD VERTICAL WOOD TRIM SUPPLIED 96" LENGTH TYP. UNLESS SPEC. (MAX 0") Ø DOWEL TO GRID 5/6" H.D. T-BAR VARIES PER SPEC EXPOSED END 3/64" [5.] LIFT & SHIFT CLIP /6" [6.99] CLIP #8x5/8" PAN HEAD SCREWS 7/8" [.3] [9.0] [6.35] ACOUSTIGREEN STANDARD CEILING TILES [6.35] TYP. REVEAL [9.05] LIFT & SHIFT VERTICAL RETURN 6" = '-0" LIFT & SHIFT CEILING PANEL SYSTEM VERTICAL RETURN DRAFTED BY: YN/BCO LAST REVISED: 5/4/6 AS NOTED

7 5/6" H.D. T-GRID SCHEDULED PARTITION " [5.43] [9.05] [6.35] TYP. REVEAL PERIMETER WALL ANGLE PERIMETER OPTIONS PANEL ON WALL ANGLE 6" = '-0" 5/6" H.D. T-GRID SCHEDULED PARTITION PERIMETER WALL ANGLE " [5.43] [9.05] [6.35] TYP. REVEAL [6.35] LIFT & SHIFT CLIP ON WALL ANGLE 6" = '-0" LIFT & SHIFT CEILING PANEL SYSTEM PERIMETER OPTIONS DRAFTED BY: YN/BCO LAST REVISED: 5/4/6 AS NOTED

8 5/6" H.D. T-GRID PANEL IN INSTALLED RESTING POSITION LIFT UP & SHIFT TO THE LEFT TILT/BRING RIGHT SIDE DOWN PANEL THEN SLIDES OUT LIFT & SHIFT INSTALLATION INSTRUCTIONS DRAFTED BY: YN/BCO LAST REVISED: 5/4/6 AS NOTED

9 5/6" H.D. T-GRID '-0" [609.54] O.C. / GRID TO GRID 5/6" H.D. T-GRID '- /6" SAFETY CLIPS PANEL IN INSTALLED RESTING POSITION [585.73] INSIDE DIM. BETWEEN TEE FLANGES '- 7/6" [595.3] OUTSIDE DIM. CLIP TO CLIP #8x5/8" PAN HEAD SCREWS 3/6" [4.75] OVERLAP ON EACH TEE FLANGE LIFT AND SHIFT CEILING SYSTEM NOTE: IF THE GRID AND CLIPS ARE INSTALLED PROPERLY THE ONLY WAYS THE CLIPS WILL COME OFF OF THE TEE FLANGE ARE AS FOLLOWS:. THE STANDARD LIFT AND SHIFT METHOD OF REMOVAL.. THE GRID HAS SHIFTED OR DISLODGED OUT OF SQUARE CAUSING ONE OR MORE OF THE CLIPS TO COME OFF OF THE FLANGE. (THIS CAN BE MINIMIZED BY THE USE OF THE ON PANELS THAT ARE NOT ROUTINELY REMOVED FOR ACCESS. THESE CLIPS ALLOW THE PANELS TO HELP HOLD THE GRID SQUARE, AND ARE FURNISHED WITH THE PANELS.) 3. THE PANEL CONTRACTED MORE THAN 3/6" OF AN INCH. (THERE WILL BE SOME NATURAL EXPANSION/ CONTRACTION OF THE PANELS DUE TO ENVIRONMENTAL CHANGES IN TEMPERATURE AND HUMIDITY. WITHIN THE SPECIFIED RANGE OF 50 DEG. F TO 86 DEG. F, AND 5% TO 55% RELATIVE HUMIDITY THE PANEL WILL CONTRACT NO MORE THAN 3/3 OF AN INCH.) 4. THE PANEL HAS BOWED MORE THAN /4 INCHES. (THIS CAN BE CAUSED BY GRAVITY SAG OR ENVIRONMENTAL CONDITIONS, PRIMARILY HUMIDITY OUTSIDE OF THE SPECIFICATIONS. SEE NO. 3.) 5. A COMBINATION OF CONTRACTION AND BOWING. (WITHIN THE SPECIFIED ENVIRON- MENTAL CONDITIONS THE COMBINATION OF BOW AND SAG WOULD HAVE TO EXCEED 5/8 OF AN INCH BOW, AND THE PANEL CONTRACTED MORE THAN 3/3 OF AN INCH.) 6. REVERSE PROCESS FOR INSTALLATION. LIFT & SHIFT INSTALLATION INSTRUCTIONS DRAFTED BY: YN/BCO LAST REVISED: 5/4/6 AS NOTED