THE NETHERLANDS (N E D E R L A N D) COMMUNICATION

Transcription

1 Vehicle Technology Division THE NETHERLANDS (N E D E R L A N D) COMMUNICATION Concerning () : - approval granted - approval extended - approval refused - approval withdrawn - production definitively discontinued of a type of CNG/LNG component pursuant to Regulation number 0. Approval number: E4-0R Extension number: 00. CNG/LNG component considered: - Container(s) or cylinder(s) () - Tank(s) or vessel(s) () - Pressure indicator () - Pressure relief valve () - Automatic valve(s) () - Excess flow valve () - Gas-tight housing () - Pressure regulator(s) () - Non-return valve(s) or check valve(s) () - Pressure relief device (PRD)(temperature triggered) () - Manual valve () - Flexible fuel lines () - Filling unit or receptacle () - Gas injector(s) () - Gas flow adjuster () - Gas/air mixer () - Electronic control unit () - Pressure and temperature sensor(s) () - CNG filter(s) () - PRD (pressure triggered) () - Fuel rail () - Heat exchanger(s)/vaporizer(s) () - Natural gas detector(s) () P.O. Box 777 Tel. + 3 (0) Vehicle Admission & Surveillance 2700 AT Zoetermeer ttv@rdw.nl The Netherlands CNG-components R0-0 v5.00 Page of 5

2 Approval number: E4-0R Extension number: 00 - LNG filling receptacle(s) () - LNG pressure control regulator(s) () - LNG pressure and/or temperature sensor(s) () - LNG manual valve(s) () - LNG automatic valve(s) () - LNG non-return valve(s) () - LNG pressure relief valve(s) () - LNG excess flow valve(s) () - LNG fuel pump(s) () - 2. Trade name or mark : LNG Manifold 3. Manufacturer s name and address : Engineered Controls International, LLC 00 RegO Drive NC 27244, Elon United States of America 4. If applicable, name and address of manufacturer s representative : 5. Submitted for approval on : January Technical service responsible for conducting approval tests : Kiwa Nederland B.V. P.O. Box AC Apeldoorn The Netherlands 7. Date of report issued by that service : November th Number of report issued by that service : Approval : granted/refused/extended/withdrawn () 0. Reason(s) of extension (if applicable) :. Place : Zoetermeer 2. Date : 3. Signature : 4. The documents filed with the application or extension of approval can be obtained upon request. () Strike out what does not apply. CNG-components R0-0 v5.00 Page 2 of 5

3 Approval number: E4-0R Extension number: 00 ADDENDUM. Additional information concerning the type approval of a type of CNG/LNG components pursuant to Regulation number 0... Natural Gas Storage System... Container(s) or cylinder(s) (for CNG system)... Dimensions :...2. Material :..2. Tank(s) or vessel(s) (for LNG system)... Capacity :...2. Material :.2. Pressure indicator.2.. Working pressure(s) (2) :.2.2. Material :.3. Pressure relief valve (discharge valve).3.. Working pressure(s) (2) :.3.2. Material :.4. Automatic valve(s).4.. Working pressure(s) (2) :.4.2. Material :.5. Excess flow valve.5.. Working pressure(s) (2) :.5.2. Material :.6. Gas-tight housing.6.. Working pressure(s) (2) :.6.2. Material :.7. Pressure regulator(s).7.. Working pressure(s) (2) :.7.2. Material :.8. Non-return valve(s) or check valve(s).8.. Working pressure(s) (2) :.8.2. Material :.9. Pressure relief device (temperature triggered).9.. Working pressure(s) (2) :.9.2. Material :.0. Manual valve.0.. Working pressure(s) (2) :.0.2. Material :.. Flexible fuel lines... Working pressure(s) (2) :..2. Material : CNG-components R0-0 v5.00 Page 3 of 5

4 Approval number: E4-0R Extension number: Filling unit or receptacle.2.. Working pressure(s) (2) :.2.2. Material :.3. Gas injector(s).3.. Working pressure(s) (2) :.3.2. Material :.4. Gas flow adjuster.4.. Working pressure(s) (2) :.4.2. Material :.5. Gas/air mixer.5.. Working pressure(s) (2) :.5.2. Material :.6. Electronic control unit.6.. Basic software principles :.7. Pressure and temperature sensor(s).7.. Working pressure(s) (2) :.7.2. Material :.8. CNG filter(s).8.. Working pressure(s) (2) :.8.2. Material :.9. PRD (pressure triggered).9.. Working pressure(s) (2) :.9.2. Material :.20. Fuel rail(s).20.. Working pressure(s) (2) : Material :.2. Heat Exchanger(s)/Vaporizer(s).2.. Working pressure(s) (2) :.2.2. Material :.22. Natural gas detector(s).22.. Working pressure(s) (2) : Material :.23. LNG filling receptacle(s).23.. Working pressure(s) (2) : Material :.24. LNG pressure control regulator(s).24.. Working pressure(s) (2) : Material :.25. LNG pressure and/or temperature sensor(s).25.. Working pressure(s) (2) : Material : CNG-components R0-0 v5.00 Page 4 of 5

5 Approval number: E4-0R Extension number: LNG manual valve(s).26.. Working pressure(s) (2) : 2.38 MPa (23.8 bar) Material : See report LNG automatic valve(s).27.. Working pressure(s) (2) : Material :.28. LNG non-return valve(s).28.. Working pressure(s) (2) : Material :.29. LNG pressure relief valve(s).29.. Working pressure(s) (2) :.59 MPa (5.9 bar) E4-0R L Material : See report LNG excess flow valve(s).30.. Working pressure(s) (2) : Material :.3. LNG fuel pump(s).3.. Working pressure(s) (2) :.3.2. Material : (2) Specify the tolerance CNG-components R0-0 v5.00 Page 5 of 5

6 TEST REPORT In accordance with ECER0 LNG Manifold Report number: Engineered Controls International, LLC 00 RegO Drive NC 27244, Elon United States of America

7 . INDEX REPORT CONTENTS Chapter Page. Index 2 2. Report history 3 3. Contact information 4 4. Summary sheet 5 5. Identification sheet 6 6. Test plan 7 7. Sample designation 9 8. Measurement equipment in use uncertainties 0 9. Index of annexes Job Reference: Initials: Adelmre P age 2

8 2. REPORT HISTORY Any modification and/or extension made to this report shall be recorded in a report history sheet and shall be inserted as a first page when opening this report. This sheet shall detail the modification and/or extension applicable to this initial report and shall clearly state where these details can be found. A copy of this sheet shall also be provided to the applicant/manufacturer, in order to keep the reports identical. Report No. Job Ref. Date Description New (initial report) LNG Manifold E4- E4-0R Signed by Test Engineer: Name: Henry Rooks Signed by Reviewer: Name: Eric Harmsen Signature: Signature: Date: Date: , Kiwa Nederland B.V., Apeldoorn. - This report may only be duplicated as a complete set without any modifications and with permission of the legitimate owner. - The test results in this report are exclusively related to the samples offered and tested. - Tests marked in this report with the IRN number are part of the accreditation scope (RvA L248) unless stated differently. - Conclusions for compliance with e.g. product standard requirements are not part of the lab scope (RvA L248). - RDW designation number for E4 and e4: RDWT-CAC-00 - KBA designation number for E and e: KBA-P With regard to measurement uncertainty information please check our website. - In case of dispute regarding this test report please contact Kiwa Nederland B.V. Job Reference: Initials: Adelmre Page 3

9 3. CONTACT INFORMATION Responsible Test House: Kiwa Nederland B.V. Address: Wilmersdorf AC Apeldoorn P.O. Box AC Apeldoorn The Netherlands Name of the Applicant: Address: Engineered Controls International, LLC 00 RegO Drive NC 27244, Elon United States of America Name of the Manufacturer: Address: Engineered Controls International, LLC 00 RegO Drive NC 27244, Elon United States of America Job Reference: Initials: Adelmre P age 4

10 4. SUMMARY SHEET Test report of the examination of the: LNG Manifold The component(s), LNG Manifold, made by the manufacturer Engineered Controls International, LLC, has/have been tested in regards to: Regulation 0 Addendum 09: Regulation No. 0 Revision 3 - Amendment 4 Incorporation all valid text up to: Supplement 3 to 0 series of amendments Date of entry into force: 8 October 206 Uniform provisions concerning the approval of: I Specific components of motor vehicles using compressed natural gas (CNG/LNG) in their propulsion system; II Vehicles with regard to the installation of specific components of an approved type for the use of compressed natural gas (CNG/LNG) in their Propulsion system. UNITED NATIONS See the identification sheet for all available product types. Signed in Acceptance: Kiwa Nederland B.V. Paul Dijkhof Unit Manager Automotive Date: Notes - The described test results are only valid for the tested materials and objects. - RDW designation number for E4 and e4: RDWT-CAC-00 - KBA designation number for E and e: KBA-P Job Reference: Initials: Adelmre Page 5

11 5. IDENTIFICATION SHEET Type break down (including specifications) LNG Manifold Approval number(s): Supplier: Type(s): Working pressure: E4-0R L Engineered Controls International, LLC LNG Manifold - Manual valve W/9464EX - PRV 9432 (E4-0R L) LNG Manifold 2.38 MPa (23.8 bar) PRV.59 MPa (5.9 bar) Temperature range: -63 C up to +85 C Material(s): see bill of materials and drawings Job Reference: Initials: Adelmre P age 6

12 6. TEST PLAN MOTIVATION TEST PLAN Based on the product(s) information the test plan is not subject to any special interpretations or modifications. The tests have been performed according to ECE R0 Annex 4N (Provisions on the approval of the manual valve for LNG applications) and Annex 5 table 5. (Test procedures). The already approved PRV9432 (E4-0R L) is part of the LNG manifold. The operating of the PRV has been controlled during the LNG manifold testing. Job Reference: Initials: Adelmre P age 7

13 File Issue: 00 Report Number: TEST SHEETS R0 LNG EQUIPMENT MANUAL VALVE Page: TS 0 Annex 4N: LNG MANUAL VALVE Key to Test Sheets: YES = YES NA = Not Applicable NT = Not Tested NO = NO Example: YES-NA-NT-NO Notes: When filling in Test Sheets, answers are crossed out which are not applicable for that clause. 6. The materials constituting the LNG manual valve which are in contact with the LNG when operating, shall be compatible with the test LNG. In order to verify this compatibility, the procedure described in Annex 5D shall be used. See below 6.2 Operating specifications 6.2. The LNG manual valve device in Class 5 shall be designed to withstand a pressure of.5 times the wording pressure at cryogenic temperature The LNG manual valve device in Class 5 shall be designed to operate at a temperature from -62 C to 85 C. 6.3 One specimen shall be submitted to a fatigue test at a pressure cycling rate not to exceed 4 cycles per minute as follows: See below See below See below Held at -62 C or lower while pressured for 00 cycles between 0 and working pressure. The maximum torque on the valve shall than comply with 2 times the force mentioned in Table 5.3 in Annex 5L. After the test the LNG manual valve shall comply with the external leak test in Annex 5B. 6.4 The LNG manual valve has to comply with the test procedures for the Class 5 component. YES-NA-NT-NO 5A Overpressure or strength YES-NA-NT-NO 5B External leakage YES-NA-NT-NO 5C Internal leakage YES-NA-NT-NO 5D CNG compatibility YES-NA-NT-NO 5E Corrosion resistance - Salt spay test - 2 ammonia test YES-NA-NT-NO YES-NA-NT-NO 5F Resistance to dry heat YES-NA-NT-NO 5G Ozone ageing YES-NA-NT-NO 5H Temperature cycle YES-NA-NT-NO 5L Durability test YES-NA-NT-NO 5N Vibration resistance YES-NA-NT-NO 5O Operating temperatures YES-NA-NT-NO Note: The materials have been tested before (see declaration sheet) Job Reference: Initials: Adelmre

14 7. SAMPLE DESIGNATION Description of the product sample Kiwa s reference no. Intake date Engineered Controls, LNG manifold C Engineered Controls, LNG manifold C Job Reference: Initials: Adelmre P age 9

15 8. MEASUREMENT EQUIPMENT IN USE UNCERTAINTIES List of general measurement equipment: Voltage High voltage test device (SPS) Vac Resistance Protective wire and insulation test device Sliding gauge Measuring tape ± 2 % Reading ± 5 % Reading ± 2 % Reading ± 5 % Reading ± 0. mm ± mm Cooling and heating < -0 C ± 5 C Cooling and heating 0 C / +00 C ± 3 C Cooling and heating > 00 C Climate chamber ± 5 % Reading ± 2 C / ± 3 %RV Ambient temperature ± C (0-30) Time =< hour Time > hour Torque Bending moment Standard weight Weighing < 30 g Weighing > 30 g Pressure (gas + air) general Barometer reading Pressure (water) Burst water pressure ± 0.2 s ± 0. % Reading ± 5 % Reading ± 5 % Reading ± 5 % Reading ± 0. % Reading ± 2 % Reading ± 5 % Reading ± 5 mbar ± 5 % Reading ± % Reading Gas tightness 0-00 cm 3 /h ± 5 cm 3 /h Gas tightness > 00 cm 3 /h Actual Flow rate (general) ± 5 % Reading ± 5 % Reading More info about measurement uncertainty of testing in the context of ISO/IEC 7025 can be found on; Job Reference: Initials: Adelmre P age 0

16 9. INDEX OF ANNEXES A. CERTIFICATION INFORMATION. Copy(ies) of issued certificate(s) by KIWA / RDW / KBA (5 pages) B. DETAILED TEST RESULTS. Result Sheets (5 pages) C. SUPPLIERS INFORMATION. Supplier declaration(s) for: a. material ( page) 2. Drawings (including data plate) (3 pages) 3. Pictures of the sample ( page) Job Reference: Initials: Adelmre Page

17 Kiwa Nederland B.V. P.O. Box AC Apeldoorn The Netherlands Page 2

18 ANNEX A CERTIFICATION INFORMATION. Copy of issued certificate by RDW (5 pages) Job Reference: Initials: Adelmre

19 ANNEX B DETAILED TEST RESULTS. Result sheets (5 pages) Job Reference: Initials: Adelmre

20 File Issue: 002 Report Number: RESULT SHEETS R0 CNG EQUIPMENT OVERPRESSURE TEST (STRENGHT TEST) Page: RS 0 Product: Engineered Controls LNG Manifold Tested in accordance with: IRN 46 Pressure Approval requirement: Annex: Regulation 0 5A Testing Equipment Kiwa no. Calibrated (due date) Operation OK Hydraulic pressure equipment 322 N.A. N.A. Pressure gauge, when tested pneumatically 939 April MPa Yes Stopwatch 207 March sec Yes Temperature Temperature equipment (room temperature) 256 July C Yes Test Conditions Complies N.A. - Test is to be performed before and after the durability test; Yes - The samples are filled with water and slowly pressurised; N.A. - The samples surface shows no visible cracks as a result of this test; Yes - Retest a new sample with a pressure gauge with accuracy +5%, if samples have failed N.A. Test Results Requirement sample no.: C60870 Moment of test Before/after Durability test Classification of component* Test pressure (kpa / MPa) *,5 x wp 2 x wp 2 x wp 2 x wp,5 x wp,5 x wp sample no.: sample no.: before After before after before after 3.57 MPa Test time > 3 min 3.02 min Rupture None None Permanent distortion None None Test dated To be monitored Conclusion Requirement Complies N.A. Samples meet requirement Yes Remarks: * Cross out which is not applicable Wp = working pressure Job Reference: Initials: Rookshe

21 File Issue: 003 Report Number: RESULT SHEET R0 CNG EQUIPMENT DURABILITY TEST (CONTINUED OPERATION) Page: RS 02 Product: Engineered Controls LNG Manifold Tested in accordance with: IRN 52 Leakage Testing Equipment Approval requirement: Annex: Kiwa no. Regulation 0 5L Calibration (due date) Operation OK Robot / PLC 927 N.A. Yes Pressure gauge 939 April MPa Yes Stopwatch 207 March sec Yes Room temperature equipment 256 July C Yes Test Conditions Complies N.A. - The test is conducted with a period of not less than 0±2 seconds; Yes - 00% of the total cycles is conducted at minimum temperature; Yes - In the off-cycle, the component pressure 50% of the test pressure; Yes - The counter of the duration test has been validated before the test has been started; Yes - After leakage testing, complete opening and closing torque has been measured. Yes Test Results Requirement sample no.:c60870 sample no.: sample no.: Component classification * Working pressure (WP)* WP WP WP WP WP WP 2.38 MPa Minimum operating temperature* -62ºC / -40ºC / -20ºC -62ºC Maximum operating temperature* 85ºC / 05ºC / 20ºC 85ºC Actual cycles performed Test cycles 00 cycles Pressure during off-cycle 50% working pressure atmospheric External leakage According to annex 5B See RS 03 Seat leakage According to annex 5C See RS 04 Component inlet size 6mm / 8mm or 0mm / 2mm 0 mm Opening torque at max temp..7nm / 2.3 Nm / 2.8Nm N.A. Closing torque at max temp.7nm / 2.3 Nm / 2.8Nm N.A. Opening torque at min temp..7nm / 2.3 Nm / 2.8Nm 0.8Nm Closing torque at min temp.7nm / 2.3 Nm / 2.8Nm 0.8Nm Date & time starting the test To be monitored Date & time stopping the test To be monitored Conclusion Requirement Complies N.A. Samples meet requirement Yes Remarks: The PRV opens at.6 MPa. Job Reference: Initials: Rookshe

22 File Issue: 004 Report Number: RESULT SHEET R0 CNG EQUIPMENT EXTERNAL LEAKAGE TEST including high and low temperature Page: RS 03 Product: Engineered Controls LNG Manifold Tested in accordance with: IRN 52 Leakage Testing Equipment Approval requirement: Annex: Kiwa no. Regulation 0 5B and 4L Calibration (due date) Operation OK Oven 906 May C Yes Cooler Liquid Nitrogen Pressure gauge 939 April MPa, Yes Leakage gauge Stopwatch 207 March sec, Yes Temperature Room temperature equipment (and temperature) 256 July C, Yes Test Conditions Complies N.A. - The sample is slowly pressurised to the test pressure as declared by the manufacturer; Yes - The sample has conditioned for 8 hours (at least) at the test temperature; Yes - The test sample is submerged in the test fluid for at least 60 sec, preferred is 900 sec; Yes - When air bubble(s) where detected after 60 sec, leakage is considered to be > 5cm 3 /h. N.A. Test Results Requirement sample no.:c60870 Test temperature room temperature 85 C / 20 C* -20 C/-40 C/-58 C* Moment of test * Corrosion / Durability / Vibration / Cycle test / Classification of component * Test pressure (kpa / MPa),5 x wp 2 x wp 2 x wp 2 x wp,5 x wp,5 x wp Before after Before after before After 2.38 MPa 3.57 MPa 2.38 MPa 2. MPa External leakage < 5cm 3 /h 0cm 3 /h 0cm 3 /h 0cm 3 /h 0cm 3 /h Test date To be monitored Conclusion Requirement Complies N.A. Samples meets requirement Yes Remarks: * Cross out which is not applicable. WP = working pressure Job Reference: Initials: Rookshe

23 File Issue: 002 RESULT SHEET R0 CNG EQUIPMENT Report Number: INTERNAL LEAKAGE TEST Page: RS 04 Product: Engineered Controls LNG Manifold Tested in accordance with: IRN 52 Leakage Testing Equipment Flow meter (for metal to metal seat only) Approval requirement: Annex: Kiwa no. Calibration (due date) Regulation 0 5C Operation OK Pressure gauge 939 April MPa Yes Leakage gauge Stopwatch 207 March sec Yes Temperature Room temperature equipment (and temperature) 256 July C Yes Test Conditions Complies N.A. - Seat leakage is tested after testing the external leakage; Yes - The sample is submerged in water (metal to metal seats excluded) and slowly pressurised; Yes - Test is carried out at room temperature; Yes - The test time is at least 20 sec, preferred is 900 sec; Yes - Valve seats are free from leakage at any aerostatic pressure from 0 to.5 times WP; Yes - Leakage on a non-return valve with metal-to-metal seat has to be 0.47dm3, at inlet pressure of 38 kpa; - The upper non-return valve seat of a filling unit has to free from leakages (up to.5 x WP). N.A. N.A. Test Results Requirement sample no.:c60870 sample no.: sample no.: Moment of test Corrosion test / endurance test / temperature cycle test Test pressure (kpa / MPa) Between 0 and,5 x wp MPa Seat leakage * No leakage / 0,47dm 3 /s No leakage Test date To be monitored before after before after before after Conclusion Requirement Complies N.A. Samples meet requirement Yes Remarks: * Cross out which is not applicable Wp = working pressure Job Reference: Initials:Rookshe

24 File Issue: 005 RESULT SHEET R0 CNG EQUIPMENT Report Number: OPERATION TEMPERATURES Page: RS 05 Product: Engineered Controls LNG Manifold Tested in accordance with: IRN 52 Approval requirement Regulation 0 Annex: 5O Test equipment used Kiwa no. Calibrated Operation OK Climate room 47 May C, Yes Stopwatch 207 March sec, Yes Room temperature 256 July C, yes TEST RESULTS Sample no.: C60870 Sample no.: Sample no.: Component is tested for Moderate temperatures: (-20 C) Component is assembled in the engine compartment (-20 C / 05 C) N.A. Component is assembled on the engine (-20 C / 20 C) N.A. Component is assembled on board (-20 C / 85 C) N.A. Component is tested for Cold temperatures: (-40 C) Component is assembled in the engine compartment (-40 C / 05 C) N.A. Component is assembled on the engine (-40 C / 20 C) N.A. Component is assembled on board (-40 C / 85 C) N.A. Component is tested for LNG temperatures: (-62 C) Component is assembled in the engine compartment (-62 C / 05 C) N.A. Component is assembled on the engine (-62 C / 20 C) N.A. Component is assembled on board (-62 C / 85 C) Yes Used test pressure (kpa/ MPa) 2.38 MPa Test monitoring date Conclusion Samples meet requirement Remarks: Complies Yes N.A. * Cross out which is not applicable Job Reference: Initials: Rookshe

25 ANNEX C SUPPLIERS INFORMATION. Supplier declaration(s) for: a. material ( page) 2. Drawings (including data plate) (3 pages) 3. Pictures of the sample ( page) Job Reference: Initials: Adelmre

26 Project no

27 4 3 2 A A (6.30) (37 JIC MALE FITTING FOR 3/4" TUBE) 4625 MANIFOLD, MANUAL VALVE AND PRV W/ 9464EX AND PRV9432 PRESSURE RATING: 5.9 BAR (230 PSIG) TEMPERATURE RATING: +65 F TO -40 F OXYGEN CLEAN PER B B 4 (.375 HEX) (.25 HEX) (.69) * ITEM DESCRIPTION MATERIAL SPEC MANIFOLD, PRV ASTM A276 S NIPPLE, INLET ASTM A276 S30400 ASTM A479 S30400 B 3 NUT, SWIVEL ASTM B6 C FITTING, STAINLESS STEEL (.875 HEX) (2.9) 5 PLUG ASTM A276 TYPE 36 S GASKET DIN 7603 COPPER 7 CAP, PRV ASTM B6 C BODY, PRV ASTM B6 C GUIDE, SPRING ASTM B6 C SEAT PTFE, VIRGIN GRADE SPRING ASTM A33 TYPE 7-7 PH 2 SCREW, ADJUSTING ASTM B6 C DISC, SEAT PCTFE, ASTM D430 TYPE GRADE 3 4 POPPET, SEAT ASTM B6 C GASKET ASTM B52 C000 6 BONNET ASTM B6 C STEM ASTM B6 C SEAT, LOWER PTFE, VIRGIN GRADE 9 PACKING, STEM PTFE VIRIGIN GRADE 20 GLAND, PACKING ASTM B6 C WASHER, SLIP ASTM D48 TYPE POM2 6 5 VIEW A-A 22 CUP, SPRING ASTM B6 C SPRING, CYLINDRICAL ASTM A33 S30200 A WASHER, SPRING 300 SERIES STAINLESS STEEL 25 NUT, LOCK 300 SERIES STAINLESS STEEL (NUT) NYLON INSERT 26 HANDLE ASTM B6 C36000 A 3 Project no SERIES STAINLESS STEEL (NUT) 27 NUT, LOCK NYLON INSERT * INDICATES PART IS PRESSURE CONTAINING 4 3 2

28 TBD B 4 A (2.76) B 3 (37 JIC MALE FITTING FOR 3/4" TUBE) 2 REVISION HISTORY REV DATE DESCRIPTION / 0/3/206 PRELIM ISSUE INLET B (2.03) (.69) NOTES: B 4 TORQUE 25±7 FT-LBS A 5 OUTLET Ø.35 ECE MARK (SEE 395-ECE SECTION A-A (2.9) (3/8-8 NPTF THD). CLEAN & PACKAGE PER B OXYGEN SERVICE. 2. LNG MANUAL (SHUT-OFF) VALVE ASSEMBLY: CERTIFIED TO UN ECE REGULATION 0 (CLASS 5). 3. TEMPERATURE RANGE: -96 C TO +85 C (-320 F TO +85 F) 4. MAX. ALLOWABLE PRESSURE: 23.8 BAR (345 PSI) 5. STAMP R0 INFORMATION ON THE BODY FLAT INDICATED. 6. APPLY 2 LAYERS OF LC503-TAPE USING OVERLAP PATTERN TO MALE NPT THREADS ON RELIEF VALVE. FREE END OF TAPE TO BE LEFT ADJACENT TO LARGER DIAMETER THREADS. LEAVE FIRST (2) THREADS FREE OF TAPE. 7. PRIOR TO ASSEMBLING INTO MANIFOLD TURN HANDLE COUNTERCLOCKWISE TILL STEM IS IN FULL OPEN POSITION. PLACE WASHER IN VALVE AS SHOWN THEN TORQUE AS SPECIFIED. 8. FOR END OF LINE FUNCTION TEST AND PERFORMANCE REQUIREMENTS SEE SPEC PURCHASE P/N: PERMANENTLY MARK ON SURFACES INDICATED: A. REGO PART NUMBER: 4625 B. ASSEMBLY DATE CODE C. HOUSING MATERIAL TRACEABILITY CODE "MMC" D. ECE R0 NO. & PART MARK: 2 TORQUE 85±5 FT-LBS SEE NOTE 7 A 3 GASKET SEE NOTE 7 (6.30) VIEW B-B STAMPING ORIENTATION Project no TEXT & FIGURES DRAWN ITEM CHECKED INSPECTED APPROVED REFERENCE NUMBER PROJECT NUM T.TICKLE QTY VARIANT DIM KIT, UPPER ASSY CAP, PRV GASKET VALVE, RELIEF MANIFOLD WELDMENT ASSY DESCRIPTION ISSUED DATE CHECKED DATE INSPECTED DATE APPROVED DATE IDENTIFIER SCALE 0/7/206 REV LEVEL LC503.75: / UNLESS OTHERWISE SPECIFIED:.05 2 PL DEC.02 3 PL DEC PL DEC.0005 ANGLES CONCENTRICITY.00 FIM FINISH 25 MAX, REMOVE BURRS, BREAK SHARP EDGES R.05 MAX INTERPRET DIMENSIONS & TOLERANCES PER ASME Y4.5M-994 A -CHANGES GAUGES- TITLE R DRAWING NUMBER O ELON, N.C EX-KITU PRV9430TP PART NUMBER ENGINEERED CONTROLS INTERNATIONAL, LLC. EG THIS DRAWING IS ECI PROPRIETARY INFORMATION. ALL RIGHTS OF DESIGN OR INVENTION ARE RESERVED. MANIFOLD, MANUAL VALVE AND PRV W/ 9464EX AND PRV R EG O CRYO-FLOW BURLINGTON, N.C DWG SIZE B A 4 3 2

29 4 3 2 REVISION HISTORY REV DATE DESCRIPTION / 0/28/206 PRELIM ISSUE 2 4 TORQUE 35±5 IN-LBS B NOTES:. CLEAN & PACKAGE PER B OXYGEN SERVICE. B 3 TORQUE 35±5 IN-LBS THEN LOOSEN /2 TURN 2. ATTACH TO HANDWHEEL. 0 A STAMP DATE CODE (MO,WK,YR).3 TEXT & FIGURES ON FLAT OF BONNET AND PART NUMBER ON OPPOSITE SIDE Project no DRAWN ITEM CHECKED INSPECTED APPROVED REFERENCE NUMBER PROJECT NUM T.TICKLE QTY VARIANT DIM SPRING, HOLDER NUT, LOCK WASHER HANDLE NUT, LOCK WASHER SPRING, CYLINDRICAL WASHER, SLIP GLAND, PACKING SEAL, LOWER PACKING, STEM GASKET SEAT & POPPET ASSY BONNET STEM DESCRIPTION ISSUED DATE CHECKED DATE INSPECTED DATE APPROVED DATE IDENTIFIER SCALE 0/28/206 REV LEVEL LC503.5 : / UNLESS OTHERWISE SPECIFIED:.05 2 PL DEC.02 3 PL DEC PL DEC.0005 ANGLES CONCENTRICITY.00 FIM FINISH 25 MAX, REMOVE BURRS, BREAK SHARP EDGES R.05 MAX INTERPRET DIMENSIONS & TOLERANCES PER ASME Y4.5M-994 A -CHANGES GAUGES- TITLE R DRAWING NUMBER O ELON, N.C SPRING CUP C A806B-7SS SS SPRING WASHER C ES A WP PART NUMBER ENGINEERED CONTROLS INTERNATIONAL, LLC. EG THIS DRAWING IS ECI PROPRIETARY INFORMATION. ALL RIGHTS OF DESIGN OR INVENTION ARE RESERVED. R EG 4" STEM ASSY RETROFIT 9464XWP-KITU O CRYO-FLOW BURLINGTON, N.C DWG SIZE B A 4 3 2

30 4. Pictures of the LNG Manifold Job Reference: Initials: Adelmre