Eurovent Product Catalogue

Transcription

1 Eurovent Product Catalogue EN 779:2012

2 Visit us online at Contents Page Eurovent Certified Performance 3 The EN 779:2012 standard 4 AIRsyntex Air Filters 5-6 Overview & Key Benefits Applications Versions Material Characteristics PROsyntex Air Filters 7-9 Overview & Key Benefits Applications Versions Material Characteristics Compact Rigid M5 - F Overview & Key Benefits Applications Versions Material Characteristics Fine Filtration M5 - M Overview & Key Benefits Applications Versions Material Characteristics 2

3 Eurovent Certified Performance Here at CFP we have a range of Eurovent approved products (Certificate No: Volz GmbH.) that you can rely on! It means you can be safe in the knowledge that our products have been tested by a third party and given a performance rating according to European and international standards helping you to compare the filters and filter media you use within your air handling units. The testing that is undertaken gives you confidence that: equipment will operate in accordance with the design specifications the energy cost will be correctly stated the products comply with the EN779:2012 standard filters will be independently tested in laboratories that are ISO certified filters live up to performance as stated in our product data sheets 4

4 The EN 779:2012 Standard Our AIRsyntex and PROsyntex ranges have both achieved the EN 779:2012 standard. This standard, introduced in October 2012, defines three filter classes: G, M and F, with previous classes F5 and F6 becoming M5 and M6. This standard states that all filter classes F7-F9 have to show an additional minimum efficiency in a treated state (induced using isopropanol, a highly flammable alcohol and solvent) at particles to reach the respective class. Filters according to the old standard EN 779:2002 may still be used, it s up to you! The new classification of the filter groups are defined by the mean efficiency measured during dust feeding and are as follows: G = filters with an efficiency of less than 40% (for 0.4µm particles). M = filters with an efficiency of between 40% and less than 80% for 0.4µm particles. This concerns the previous filters F5 and F6 which are now referred to as M5 and M6. F = filters with an efficiency of more than 80% for 0.4µm particles. Class F has a minimum efficiency for both a discharged and a charged state. The below table gives an overview of the new filter groups of the EN 779:2012 standard: Group Class Average gravimetric arrestance (Am) [%] Average efficiency (Em) for 0,4μm particles [%] Minimum efficiency for 0,4μm particles [%] Final pressure drop [Pa] Coarse G G G G4 > Medium M M Fine F F F9 - >

5 AIRsyntex Air Filters Our range of efficient, environmentally-friendly, AIRsyntex Air Filters offer consistent performance and great value for money which is why they are widely used in so many environments, from retail, commercial, healthcare, education, engineering, hotels and leisure to pharmaceutical. Choose AIRsyntex Air Filters for fully compliant, clean air solutions. THE KEY BENEFITS High indoor air quality Free from harmful substances, our filters are made from non-shedding synthetic media, which means they don t harm your health and provide high indoor air quality, unlike brittle glass media where there is a risk of fibre shedding. Environmentally-friendly Oeko-Tex 100 approved, our filters are made from synthetic media, and are free from harmful substances, meaning the AIRsyntex filters can also be incinerated rather than going to landfill. High performance Efficient and high performing, you can rest assured our air filters have achieved EN 779 F7 F standards and are Eurovent approved. Glass Fibre Synthetic Fibre Air conditioning & ventilation technology Painting & drying technology 5

6 AIRsyntex Pocket Filters Pocket filter AIRsyntex M5 - F9 All tested according to EN 779:2012 APPLICATIONS For fine filtration in heat ventilation and air conditioning devices and plants of all kinds. / Offices, hospitals, computing centres / Pharmaceutics, fine-mechanical and food industry / Pre filtration e.g. for HEPA filters VERSIONS CLASSIFICATION / Filter class F7 / Filter class F8 / Filter class F9 How to install pocket filters / Full range of standard sizes, bespoke sizes available upon request / Frame types: - Metal frame (20 or 25mm), - Plastic frame (25mm) / Filters with plastic frames are fully incinerable / Option to have a foamed hygiene-gasket MATERIAL CHARACTERISTICS / Tested according to EN 779:2012 / Oeko-Tex 100 approved, environmentally friendly so can be incinerated rather than going to landfill (when choosing plastic frames) / Fire prevention requirements according to DIN (F1) / Humidity resistant up to 100% r. h. / Lacquer compatibility according to IPA-control / Higher density and pressure load due to endless pockets and their edge welding / Environmentally safe non-shedding synthetic fibres / Temperature resistant up to a maximum of 80 C depending on type of frame Correct Pockets stand vertically and are open to enable maximum dust holding. Air conditioning & ventilation technology Incorrect Pockets fall, unable to hold the maximum dust capacity, with lower pockets running the risk of absorbing condensed water. Painting & drying technology 6

7 PROsyntex Air Filters Our range of PROsyntex Air Filters are a class leading solution for clean air quality, EN779 F7 F registered, Eurovent approved and certified by the Institute for Air Hygiene. Used by some of the leading air handling unit manufacturers, facilities management companies and major brands in the UK. Choose PROsyntex Air Filters to help maintain a safe, compliant and comfortable working environment. THE KEY BENEFITS 1 High indoor air quality Free from harmful substances, our filters are made from non-shedding synthetic media, which means they don t harm your health and provide high indoor air quality, unlike brittle glass media where there is a risk of fibre shedding. 2 Longer service life The tight woven, ultra fine fibre structure with two stage filtration, ensures high dust holding capacity for longer service life, saving energy and money. Glass Fibre AIRsyntex PROsyntex 3 Environmentally-friendly Oeko-Tex 100 approved, our filters are made from synthetic media, and are free from harmful substances, meaning the PROsyntex filters can also be incinerated as opposed to going to landfill. P F S Clean air side PROsyntex offers three layers of filtration. 4 Energy saving With a large dust holding capacity, three stage filtration system and longer service life, PROSyntex Air Filters increase efficiency and reduce direct energy required, thereby reducing CO² emissions and running costs. 7 Air conditioning & ventilation technology Painting & drying technology

8 PROsyntex Pocket Filters Pocket filter PROsyntex M5 - F9 All tested according to EN 779:2012 APPLICATIONS For fine filtration in heat ventilation and air conditioning devices and plants of all kinds. / Offices, hospitals, computing centres / Pharmaceutics, fine-mechanical and food industry / Pre filtration e.g. for HEPA filters VERSIONS / Full range of standard sizes, bespoke sizes available upon request / Frame types: - Metal frame (20 or 25mm), - Plastic frame (25mm) / Filters with plastic frames are fully incinerable / Option to have a foamed hygiene-gasket / PROsyntex F7 as biostatic version CLASSIFICATION / Filter class F7 / Filter class biostatic F7 / Filter class F8 / Filter class F9 How to install pocket filters MATERIAL CHARACTERISTICS / Tested according to EN 779:2012 / Oeko-Tex 100 approved, environmentally friendly so can be incinerated rather than going to landfill (when choosing plastic frames) / Fire prevention requirements according to DIN (F1) / Humidity resistant up to 100% r. h. / Lacquer compatibility according to IPA-control / Higher density and pressure load due to endless pockets and their edge welding / Environmentally safe non-shedding synthetic fibres / Temperature resistant up to a maximum of 80 C depending on type of frame Correct Pockets stand vertically and are open to enable maximum dust holding. Air conditioning & ventilation technology Incorrect Pockets fall, unable to hold the maximum dust capacity, with lower pockets running the risk of absorbing condensed water. Painting & drying technology 8

9 Technical data sheet PROsyntex Pocket filter fine filtration Standard F7 Technical data: Medium Colour medium Frame Synthetic - Progressive microfibre Pink Plastic frame (25 mm) Metal frame (20 or 25 mm) Filter dimensions (width x height x depth) [mm] 592 x 592 x 635 Number of pockets 12 Filter area [m²] 9.0 Filter class F7 Recommended nominal air flow [m³/h] 3400 Initial pressure drop approx. [Pa] 92 Recommended final pressure drop [Pa] 450 Average arrestance [%] 90 Average efficiency (0,4 μm) [%] 80 < 90 Discharged efficiency of medium (0,4 m) [%] > 35 Maximum humidity resistance [%] 100 Max. operating temperature [ C] - depending on type of frame 80 Labelling Energy efficiency Dimension, filter class, type test B Characteristics of test: Classification EN 779:2012 Fire prevention requirements Pollutant tested DIN (F1) Oeko - Tex Standard 100 product class II (Products with skin contact) Product Benefits: Endless pockets and edge welding for higher density and pressure load 3-layer filter medium for best arrestance, low pressure loss and high retention capacity Pocket-Fitting for a optimal distribution of incoming flow, effective use of the filter area and form stability Optional available with abrasion-resistant, silicone-free and closed porous hygiene-gasket Also available in anti-bacterial finish, Biostat 9

10 Compact Rigid Compact Filters M5 - M9 All tested according to EN 779:2012 Our range of efficient, environmentally-friendly Compact Rigid V-Filters can be directly installed in existing filter housings with no modification required. Tested according to EN 779:2012, they offer outstanding performance and high indoor air quality. They are ideal for use in hospitals, pharmaceutical and food industries as well as office environments and computer centres. Choose Compact Rigid Filters for outstanding indoor air quality. THE KEY BENEFITS High air quality The high performance non-shedding synthetic media promotes high indoor air quality. Environmentally Friendly The compact V shaped configuration creates a large surface area giving a high dust holding capacity. This coupled with a high final pressure drop across the filters gives a long service life, saving time, energy and money. Longer service life Compact Rigid filters are fully incinerable and easy to dispose without the need to go to landfill. Air conditioning & ventilation technology Painting & drying technology 10

11 Compact Rigid Compact Filters Filter classes G1-4 M5-6 F7-9 E10-12 H13-14 U15-17 G M F E H U Compact Rigid M5 - M9 All tested according to EN 779:2012 Particle sizes (not true to scale) APPLICATIONS / Hospitals, offices and computer centres / Pharmaceutical and food environments / Fine mechanics / Fine pre-filtration for HEPA filters VERSIONS MATERIAL CHARACTERISTICS / Tested according to EN 779:2012 / Tested and certified by ILH Berlin / Fire prevention requirements according to DIN (F1) / Lacquer compatibility according to IPA-control / Humidity resistant up to 100% r.h. / Temperature resistant up to 80 o C / 20 and 25mm headers CLASSIFICATION / Filter class M5-M9 Standard versions Compact Rigid M5 - F9 / The compact v-shaped configuration creates a large surface area Width Height Depth Filter surface Extremely stable plastic welded casing FRAME DEPTH 20 or 25MM mm mm mm m² Please order in the following sequence: Width x Height x Depth 11

12 Technical data sheet Compact Rigid M5-M9 Panel Filters Compact Rigid V-Filter; F7 592 x 592 x 292 mm; 8 filter packs 300 Graph Compact Rigid V-Filter F7 Nominal air flow rate (m³/h) Initial pressure drop (Pa) Recommended final pressure drop (Pa) 650 Average efficiency (0.4µm) (%) Filter area (m²) 19 Information: The recommended final pressure drop for compact filters is 650 Pa (filter classes M5 - M6 and F7 - F9) Initial pressure drop [Pa] Anfangsdruckdifferenz [Pa] Kompaktfilter Compact F7 F Volumenstrom Air flow rate [m³/h] 12

13 Fine Filtration Synthetic Media M5 - M6 All tested according to EN 779:2012 A safe and environmentally friendly alternative to glass fibre, our range of nonshedding synthetic fine filtration media are tested according to EN 779:2012 and are ideal for general industrial painting and paint spraying units. Choose Fine Filtration Synthetic Media for optimum final filtration. THE KEY BENEFITS Silicone free All of our fine filtration synthetic media versions are silicone free. High quality filtration The progressive structure of this non-shedding synthetic media means the full depth of the material is used, increasing its dust holding capacity. All of the V5 and V6 medias are available tackified with dust adhesive to ensure greater stickiness of dust particles to the media material. Environmentally friendly All our Fine Filtration Synthetic Media are fully incinerable. Flexible Available in various size rolls, cut pads, filter socks and wire frames. Air conditioning & ventilation technology Painting & drying technology 13

14 Fine Filtration Synthetic Media Filter classes G1-4 M5-6 F7-9 E10-12 H13-14 U15-17 G M F E H U Fine Filtration M5 - M6 All tested according to EN 779:2012 Particle sizes (not true to scale) APPLICATIONS / Spray booth 1st stage filtration / Spray booth 2nd stage filtration / General industrial paint spraying / General air filtration VERSIONS / Six variations in the range / V500S, V560G, V600G and V5micron are tackified / V560G, V600G and V5micron have a rear scrim MATERIAL CHARACTERISTICS / Tested according to EN 779:2012 / Reliable shatterproof synthetic fibres / Non-shedding / Fire prevention requirements according to DIN (F1) / Humidity resistant up to 100% r.h. / Temperature resistant up to 80 o C / Silicone free / V560G, V600G and V5 micron have a polyester backing on the clean air side for greater stability in any frame. CLASSIFICATION / Filter class M5-M6 Dust air side Dust air side Clean air side Clean air side / Progressive Structure / High performance media 14

15 Technical data sheet Fine Filtration M5 - M6 Synthetic Media Versions Fine Filtration Media M5 - M6 Product Filter class Material thickness approx. Surface weight approx. Initial pressure drop Recommended final pressure drop Nominal Airflow Rate Air velocity Average arrestance mm g / m² Pa Pa m³ / h / m² m / s % V300S M V400S M V500S M V560G M V600G M V5micron M

16 Concept Filter Products Unit 5, Bredbury Court, Ashton Road, Bredbury, Stockport. SK6 2QB t: conceptfilterproducts CFPdirect concept-filter-products-ltd