QUV Commissioning Checklist

Size: px

Start display at page:

Download "QUV Commissioning Checklist"

Matilda Blair
5 years ago
Views:

1 QUV Commissioning Checklist Section 1: Contact Information First Name: Last Name: Company: Address: Address 2: City: State/Province: Postal/Zip: Country: Phone Number: Section 2: General Questions 1. Tester Model: o QUV/basic o QUV/se o QUV/spray o QUV/cw 2. Serial Number: 3. Voltage Rating: 4. Have you fully read and understood the Quick Setup Guide? o Yes o No 5. Have you registered your tester on Q-Lab.com? o Yes o No 6. Did the tester arrive free of any shipping damage? o Yes o No 7. Please take photos of any shipping damage. 8. Please take at least two photographs (at least one from the front and side) showing the tester in its final installation position. 9. Please measure the clearance on all four sides of the tester. Units: o Centimeters o Inches Front: Back: Left Side: Right Side: LU-8175 REV A Q-Lab QUV Commissioning Checklist Page 1 of 5

2 Section 3: Room/Lab Condition Questions 10. What is the primary use of the building where the tester has been installed? o Offices o Research & Development o Testing Laboratory o Production o Other (explain below) If Other, please explain: 11. What is the primary use of the room where the tester has been installed? o Offices o Research & Development o Testing Laboratory o Production o Other (explain below) If Other, please explain: 12. What is the approximate size of the room where the tester has been installed? Units: o m 2 o ft Is there any process in the room that generates dust, particles, vapors, etc. (e.g. mixing, painting, cutting, etc.)? o Yes o No 14. Please list the other equipment in the same room as the tester: 15. Is there an HVAC (heating/ventilation/air-conditioning) system in the room? o Yes o No 16. Are the controls for the HVAC in the room? o Yes o No 17. Please indicate the highest laboratory temperature and relative humidity that the room will experience with the tester operating. Please consider summer and winter in your answer. Tempertaure: Units: o C o F %RH: 18. Please indicate the lowest laboratory temperature and relative humidity that the room will experience with the tester operating. Please consider summer and winter in your answer. Tempertaure: Units: o C o F %RH: 19. Is the HVAC system shut off or reduced at night? o Yes o No 20. Is the tester located near a window or underneath or near an HVAC vent? o Yes o No LU-8175 REV A Q-Lab QUV Commissioning Checklist Page 2 of 5

3 Section 4: Utility (Electrical and Water) Questions 21. What is the nominal line voltage (VAC)? 22. What is the frequency? o 50 Hz o 60Hz 23. What is the actual, measured line voltage (VAC)? 24. What is the actual, measured voltage beween neutral and ground (VAC)? 25. Is the tester connected through an external transformer? o Yes o No If yes, please list transformer manufacturer and model: 26. Input Frequency (Hz): Output Frequency (Hz): 27. Input Voltage (Volts): Output Voltage (Volts): 28. Input Current (Amps): Output Current (Amps): 29. Have you ever experienced brown-outs or voltage spikes/irregularities? o Yes o No 30. Does any other equipment in the room utilize voltage stabilizers or surge protection equipment? 31. What is the current rating on the circuit breaker that the tester is connected to (Amps)? 32. Is there any other equipment on the same circuit as the tester? o Yes o No 33. Has the tester been connected to power by a certified electrician, per the Quick Setup Guide o Yes o No 34. Please take a photo of the electrical connections at the back of the tester, and at the circuit breaker. 35. Is the tester connected to a water purification system? o Yes o No LU-8175 REV A Q-Lab QUV Commissioning Checklist Page 3 of 5

4 If yes: Manufacturer of system Type of system (e.g. RO/DI, etc.) Capacity of system: Units: o LPM o LPH o GPM o GPH Nominal water quality system is designed to produce: Units: oppm TDS omω-cm resistivity oµs/cm conductivity Type of monitoring system (e.g. TDS, silica, etc.) If monitoring system has a meter, what is the value displayed? Pressure system is designed to operate at o_bar o_psi o_kpa Incoming water pressure o_bar o_psi o_kpa Does the water system have a repurification or recirculating system installed? o Yes o No If yes, who is the manufacturer? What is the tubing material made from, between the water purification system and the tester? Are there any iron, copper or brass lines or fittings between the tester and the primary water purification system? o Yes o No 36. Does your tester have a water pressure gauge? o Yes o No If yes, what is the actual water pressure, measured on the gauge (in psi)? 37. QUV/spray models only: What is the flow rate of the water during a spray step, measured in liters per minute (LPM)? 38. Is the main water drain below the tester drain? o Yes o No If yes, please indicate the distance: Units: o mm o cm o in If no, are you using a booster or sump pump? o Yes o No If no, please explain: 39. What is the diameter of the smallest restriction in the entire drain system? Units: o mm o cm o in 40. Please take a photo of the drain system. Section 5: Misc. Questions 41. What type of lamps are installed into the QUV tester? o Q-Lab UVA-340 o Q-Lab UVB-313EL o Q-Lab UVA-351 o Q-Lab Cool White o Q-Lab QFS-40 o Other LU-8175 REV A Q-Lab QUV Commissioning Checklist Page 4 of 5

5 If other, please explain: 50. What is the size and type of specimens that you are testing? 51. Are you using specimen holders? o Yes o No 52. Is the QUV located on a space saver frame? o Yes o No 53. What are the test standards or cycles that you plan to run in the tester? Submitted By: (First and last name of person who completed this form): Approved By: (For Q-Lab use only): LU-8175 REV A Q-Lab QUV Commissioning Checklist Page 5 of 5

QUV Accelerated Weathering Testers. The Most Trusted Name in Weathering

QUV Accelerated Weathering Testers www.q-lab.com The Most Trusted Name in Weathering Why Test? Meet Specifications Meet customer requirements Stay ahead of government regulations Prevent Field Failures