Description. cleaning. Recommended Use. Basketball courts Volleyball courts Racquetball Badminton courts Multi-purpose gym and stage Aerobic floors

Transcription

1 FULL COURT PRESS LOW ODOR SPORTS FLOOR FINISH Environment, Health & Safety Low odor VOC compliant No Ethylene-based Glycol Ethers No N-Methyl-Pyrrolidone (NMP) No Nonylphenyl Ethoxylates (NPE) Passes ASTM D for Slip Resistance (MFMA test procedure) What the Pros Know Preventative Maintenance will extend the life of your floor finish. Simple steps such as placing walk-off mats in door ways to keep out dirt and grit and avoiding excess moisture from tracked in water or leaks will prolong the life of your floor. Having a planned daily maintenance schedule of dry mopping or damp mopping over spills can help reduce overall labor costs. Periodic maintenance steps will be needed to keep the look and feel of the finish up to your standards. With this step, an autoscrubber or 175 rpm buffer with a white pad is used with the NewAge Replay Maintenance Cleaner to give a more thorough, deep cleansing. This will minimize the chance of contamination from damaging the floor and reducing overall labor costs. Full Court Press exceeds the minimum slip resistance requirements for floor finishes when tested in accordance with ASTM D (MFMA test procedure) Technical Data Sheet Description NewAge Full Court Press is a premium finish developed specifically for the wood sport floor market, providing a tough, high-build urethane finish. This product provides excellent chemical resistance, protecting against perspiration and routine cleaning. Recommended Use Basketball courts Volleyball courts Racquetball Badminton courts Multi-purpose gym and stage Aerobic floors Features Provides excellent chemical resistance Protects against perspiration and routine cleaning Easy to maintain Extremely durable one-component sport floor finish Very low VOC VOC does not exceed 145 grams per liter Virtually odorless Fast drying Approximately 2-3 hours Available in gloss Nonflammable Water clean-up Slightly Amber Will adhere to most solvent-based and waterborne finishes after proper preparation, drying, and curing times Our most durable one component sport floor finish Provides excellent chemical resistance Virtually odorless Easy to maintain Very low VOC BILLERICA, MA CS /09

2 DIRECTIONS FOR USE: BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS FOR NEW INSTALLATION OF SPORT FLOORS, USE ONLY IN STRUCTURES WITH HUMIDITY AND TEMPERATURE CONTROLS. DO NOT USE OVER CHANNEL AND CLIP FLOOR SYSTEMS IN ENVIRONMENTS NOT CONTROLLED FOR TEMPERATURE AND HUMIDITY. ABRADE AND RECOAT EXISTING FLOORS 1. Be sure floor is free from wax or oily residue. 2. Clean floor thoroughly with NewAge Replay Maintenance Cleaner and use NewAge Recoat Conditioner and Prep Cleaner system (see label for directions). 3. When recoating over other manufacturers finishes, check with manufacturer for abrading recommendations. 4. Vacuum thoroughly. 5. Tack with untreated dust mop or slightly water-dampened towel. 6. Apply 1-2 coats of a NewAge finish (see finish directions). Note: Full Court Press will adhere to most finishes after proper preparation and dry times. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY. SANDING AND FINISHING NEW FLOORS 1. Sand and prepare the floor using MFMA-accepted methods. 2. Make your final cut with grit paper. Screen with grit screen. This burnishing will reduce the amount of grain raise. 3. Vacuum thoroughly. 4. Tack with untreated dust mop or slightly water-dampened cloth or towel. 5. Apply sealer and paint using MFMA-accepted methods then apply finish system (see finish directions). INTERCOAT ABRASION FOR FLOORS WITHOUT GAME LINES: Abrading between finish coats is not necessary for adhesion unless it has been more than 48 hours since the previous coat has been applied. INTERCOAT ABRASION FOR FLOORS WITH GAME LINES: Apply game lines over the first coat of finish. Before applying game lines, abrade with a Floor Prep Pad (FPP) or 120-grit screen then vacuum and tack thoroughly. BEFORE APPLYING GAME LINES, ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY AND ADHESION. DO NOT USE PAINT CONTAINING VINYLS OR POLY-VINYLS. Abrade dry game lines with a FPP or 120-grit screen to ensure adhesion of finish. Apply finish coat. Abrading between finish coats is not necessary for adhesion of finish, unless it has been more than 48 hours since the previous coat has been applied. Always vacuum and tack thoroughly after abrading. FINISHING: SHAKE WELL BEFORE USING. 1. Pour a 4 wide line of finish along the starting wall. Go with the grain of the wood. 2. Using a clean, pre-dampened, NewAge Lightweight (LW) 18" Applicator; draw the applicator forward, with the grain of the wood, moving the finish toward the opposite wall. Holding the applicator at a snowplow angle will maintain a wet edge at all times. 3. At the end of each run, turn the applicator toward you and pad out the applicator parallel to the wet edge. 4. Feather out all turns. If pushed too hard or too fast, drips will fly off the applicator. 5. Missed areas can be touched up if seen right away. 6. To prevent lapping and dry marks, be sure you are using the recommended coverage of sq.ft. per gallon. Be careful not to spread the finish too thin. 7. Allow your first coat to dry 2-3 hours. NOTE: Allow final coat to dry at least 48 hours before use. DRY TIME/CURING: With conditions of 65 to 80 F and 40 to 60% humidity this finish will dry in 2-3 hours. The curing process takes approximately 7 days. The floor may be walked on after 24 hours, but the finish is susceptible to scuffing and marring prior to completion of the curing time. Do not replace athletic or walk-off mats until finish is fully cured. Do not clean with water or detergent during the first week. CLEAN-UP: Tools should be cleaned with water and stored. STORAGE: FREEZE-THAW STABLE. Product should always be stored in a climate controlled environment. Do not store above 100 F. If frozen, allow product to thaw out at room temperature before applying. MAINTENANCE: Place walk-off mats at all entrance doorways to keep out excessive dirt and grit. See NewAge Replay Maintenance Cleaner instructions for cleaning and maintenance information. SPECIFICATIONS/PHYSICAL DATA: Physical Characteristics: Ingredients - Water ( ), polymeric resin (Proprietary), Propylene-based glycol ether (Proprietary), leveling and defoaming agents (Proprietary). Color - Milky, off white (wet) Gloss Level - (60 ) 88 ph Odor - Non-offending Solids Flash Point F Viscosity - (#4 Ford 25 C) approx. 16 seconds Stability - One year shelf life in unopened container Density lbs./gallon (1.04 S.G.) VOC - Does not exceed 145 grams per liter (1.2 pounds per gallon) Packaging - 5-gallon plastic pail Application Characteristics: Clarity - Clear when dry Coverage sq. ft. per gallon Leveling - Excellent Percent Cured After 24 Hours - 70%; after 72 hours - 90% Defoaming - Excellent Maximum Cure - 100% in one week Drying Time hours Application Tools - NewAge Lightweight (LW) 18" Applicator, flocked foam cut-in pad

3 DOUBLE OVERTIME LOW ODOR SPORTS FLOOR FINISH Environment, Health & Safety Low odor No Ethylene-based Glycol Ethers VOC compliant (except SCAQMD) Passes ASTM D for Slip Resistance (MFMA test procedure) What the Pros Know Preventative Maintenance will extend the life of your floor finish. Simple steps such as placing walk-off mats in door ways to keep out dirt and grit and avoiding excess moisture from tracked in water or leaks will prolong the life of your floor. Having a planned daily maintenance schedule of dry mopping or damp mopping over spills can help reduce overall labor costs. Periodic maintenance steps will be needed to keep the look and feel of the finish up to your standards. With this step, an autoscrubber or 175 rpm buffer with a white pad is used with the Replay Maintenance Cleaner to give a more thorough, deep cleansing. This will minimize the chance of contamination from damaging the floor and reducing overall labor costs. Double Overtime exceeds the minimum slip resistance requirements for floor finishes when tested in accordance with ASTM D (MFMA test procedure) Technical Data Sheet Description NewAge Double Overtime is our top sport finish for durability and appear ance. A premium two-component waterborne wood floor finish, specifically formulated for use on maple sport floors, providing a tough, high-build urethane finish. Recommended Use Basketball courts, Volleyball courts Racquetball Badminton courts Multi-purpose gym and stage Aerobic floors Features Our most durable sport floor finish available Non-yellowing stays clean and clear even after several recoats Provides excellent chemical resistance Protects against perspiration and routine cleaning Easy to maintain Available in gloss VOC compliant (except SCAQMD), VOC does not exceed 350 grams per liter Virtually odorless Fast drying Approximately 2-3 hours Nonflammable Water clean-up Will adhere to most solvent-based and waterborne finishes after proper preparation, drying, and curing times Our most durable sport floor finish Non-yellowing stays clean and clear even after several recoats Virtually odorless Easy to maintain BILLERICA, MA CS /09

4 DIRECTIONS FOR USE: BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS. For new installation of sport floors, use only in structures with humidity and temperature controls. DO NOT USE over channel and clip floor systems in environments not controlled for temperature and humidity. ABRADE AND RECOAT EXISTING FLOORS 1. Be sure floor is free from wax or oily residue. 2. Clean floor thoroughly with NewAge Replay Maintenance Cleaner and use NewAge Recoat Conditioner and Prep Cleaner system (see label for directions). 3. When recoating over other manufacturers finishes, check with manufacturer for abrading recommendations. 4. Vacuum thoroughly. 5. Tack with untreated dust mop or slightly water-dampened towel. 6. Apply 1-2 coats of a NewAge finish (see finish directions). Note: Double Overtime will adhere to most finishes after proper preparation and dry times. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY. SANDING AND FINISHING NEW FLOORS 1. Sand and prepare the floor using MFMA-accepted methods. 2. Make your final cut with grit paper. Screen with grit screen. This burnishing will reduce the amount of grain raise. 3. Vacuum thoroughly. 4. Tack with untreated dust mop or slightly water-dampened cloth or towel. 5. Apply sealer and paint using MFMA-accepted methods then apply finish system (see finish directions). INTERCOAT ABRASION FOR FLOORS WITHOUT GAME LINES: Abrading between finish coats is not necessary for adhesion unless it has been more than 48 hours since the previous coat has been applied. INTERCOAT ABRASION FOR FLOORS WITH GAME LINES: Apply game lines over the first coat of finish. Before applying game lines, abrade with a Floor Prep Pad (FPP) or 120-grit screen then vacuum and tack thoroughly. BEFORE APPLYING GAME LINES, ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY AND ADHESION. DO NOT USE PAINT CONTAINING VINYLS OR POLY-VINYLS. Abrade dry game lines with a FPP or 120-grit screen to ensure adhesion of finish. Apply finish coat. Abrading between finish coats is not necessary for adhesion of finish, unless it has been more than 48 hours since the previous coat has been applied. Always vacuum and tack thoroughly after abrading. FINISHING: SHAKE OR STIR WELL BEFORE USING. 1. Add NewAge X-Link per label directions. 2. Pour a 4 wide line of finish along the starting wall. Go with the grain of the wood. 3. Using a clean, pre-dampened NewAge Lightweight (LW) 18" Applicator; draw the applicator forward, with the grain of the wood, moving the finish toward the opposite wall. Holding the applicator at a snowplow angle will maintain a wet edge at all times. 4. At the end of each run, turn the applicator toward you and pad out the applicator parallel to the wet edge. 5. Feather out all turns. If pushed too hard or too fast, drips will fly off the applicator. 6. Missed areas can be touched up if seen right away. 7. To prevent lapping and dry marks, be sure you are using the recommended coverage of sq.ft. per gallon. Be careful not to spread the finish too thin. 8. Allow your first coat to dry 2-3 hours. NOTE: Allow final coat to dry at least 48 hours before use. DRY TIME/CURING: With conditions of 65 to 80 F and 40 to 60% humidity this finish will dry in 2-3 hours. The curing process takes approximately 7 days. The floor may be walked on after 24 hours, but the finish is susceptible to scuffing and marring prior to completion of the curing time. Do not replace athletic or walk-off mats until finish is fully cured. Do not clean with water or detergent during the first week. CLEAN-UP: Tools should be cleaned with water and stored. STORAGE: FREEZE-THAW STABLE: Product should always be stored in a climate controlled environment. Do not store above 100 F. If frozen, allow product to thaw out at room temperature before applying. MAINTENANCE: Place walk-off mats at all entrance doorways to keep out excessive dirt and grit. See NewAge Replay Maintenance Cleaner instructions for cleaning and maintenance information. POT LIFE: The finish/x-link mixture is active for 8 hours after it is mixed. Within 2-3 days, X-Link may be added one additional time. SPECIFICATIONS/PHYSICAL DATA: Physical Characteristics: Ingredients - Water ( ), polyurethane resin (Proprietary), N-Methyl-2-Pyrrolidone ( ), Dipropylene Glycol Monomethyl Ether ( ) and Dipropylene Glycol N-Butyl Ether ( ) Color - Milky, off white (wet) Gloss Level - (60 ) 88+ ph Odor - Non-offending Solids - 28% Flash Point -200 F Viscosity - (#4 Ford 25 C) approx. 16 seconds Stability - One year shelf life in unopened container Density lbs./gallon (1.02 S.G.) VOC - Does not exceed 350 grams per liter (2.9 pounds per gallon) Packaging - 5-gallon plastic pail Comes complete with crosslinker Application Characteristics: Clarity - Clear when dry Coverage sq. ft. per gallon Leveling - Excellent Percent Cured After 24 Hours - 80%; after 72 hours - 90% Defoaming - Excellent Maximum Cure - 100% in one week Drying Time hours Application Tools - NewAge Lightweight (LW) 18" Applicator, flocked foam cut-in pad.

5 RECOAT CONDITIONER AND PREP CLEANER Environment, Health & Safety No alcohol No ammonia ph neutral What the Pros Know Preventative maintenance will extend the life of your floor finish. Simple steps such as placing walk-off mats in door ways to keep out dirt and grit and avoiding excess moisture from tracked in water or leaks will prolong the life of your floor. Having a planned daily maintenance schedule of dry mopping or damp mopping over spills can help reduce overall labor costs. Periodic maintenance steps will be needed to keep the look and feel of the finish up to your standards. With this step, an autoscrubber or 175 rpm buffer with a white pad is used with the NewAge Replay Maintenance Cleaner to give a more thorough, deep cleansing. This will minimize the chance of contamination from damaging the floor and reducing overall labor costs. Technical Data Sheet Description NewAge Recoat Conditioner and Prep Cleaner is a specially formulated recoat adhesion system for all types of polyurethane finished hardwood floors, including factory prefinished floors. This product conditions and prepares the existing finish to optimize adhesion of the new coat of finish. Recommended Use Aluminum oxide, ceramic, and other factory prefinished floors Basketball courts Volleyball courts Racquetball Badminton courts Multi-purpose gym and stage Aerobic floors Features Cleans and conditions existing finish to optimize adhesion of new coat of finish. Fast just spray and buff. Easy doesn t require special training or certification. Convenient pre-mixed and ready to use. Recoat Conditioner and Prep Cleaner removes scuffs and surface scratches, rather than just covering them. No extra tools needed. Minimal dust with a Prep Pad. Economical. Economical Fast and easy to use Optimizes adhesion Removes scuffs and surface scratches BILLERICA, MA CS /09

6 DIRECTIONS FOR USE: BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS. NewAge Recoat Conditioner and Prep Cleaner conditions, deep cleans and prepares the existing finish to optimize adhesion of the new coat of finish. This product is designed to be used full-strength as packaged, DO NOT DILUTE. PRIOR TO USE: Prepare a sample test area using the Recoat Conditioner and Prep Cleaner to determine general compatibility prior to recoating. For factory prefinished flooring, contact the manufacturer for specific recoat recommendations. NOTE: Do not use this product on any floor that has been waxed, polished, oiled or has been maintained with a commercial maintenance coating. HOW TO USE: 1. Vacuum or sweep floor thoroughly to remove loose dirt and grit. 2. WHEN USING A STRING MOP: Apply Recoat Conditioner and Prep Cleaner over 3 x 24 sections of the floor at the rate of 2,000 square feet per gallon. Be careful not to apply too heavily. Surface should be damp enough to be slightly wet after abrading using a standard speed (175 rpm) buffer with a Floor Prep Pad (FPP). This cleans the floor to ensure any foreign material is removed, as well as conditions and prepares the old finish to optimize adhesion of the new coat of finish. WHEN USING AN AUTOSCRUBBER: Set at normal maintenance settings for proper application rate and pad pressure. Use a FPP driven by whatever maintenance pad is typically used. NOTE: Regardless of the size of area, be sure to overlap sections to ensure that no areas are missed. 3. Remove all residues immediately using a wrung-out cotton towel or cloth dampened with Recoat Conditioner and Prep Cleaner. 4. Abrade the floor once it has dried using two FPP's (one driving the other) so that the pad more effectively contours to the surface of the flooring. This will ensure abrasion of the edges next to any overwood and in the grain pattern optimizing adhesion of the finish topcoat. Beveled edges and any visibly unabraded areas should be cleaned and abraded by hand. 5. Tack the floor again to remove dust using a wrung-out cotton towel or cloth dampened with Recoat Conditioner and Prep Cleaner. 6. When completely dry, apply a NewAge Sport brand floor finish immediately, following the label directions. Make sure the Recoat Conditioner and Prep Cleaner solution is completely dry before applying finish. STORAGE: FREEZE-THAW STABLE. Product should always be stored in a climate controlled environment. Do not store above 100 F. If frozen, allow product to thaw out at room temperature before applying. CLEAN-UP: Clean all tools and equipment with water. SPECIFICATIONS/PHYSICAL DATA: Physical Characteristics: Ingredients - Surfactants (Proprietary), Dipropylene Glycol Monomethyl Ether ( ), Ethylene Glycol Monoethyl Ether ( ), water, other proprietary ingredients (Proprietary) Color - Amber (wet) Gloss Level - N/A ph Odor - Light antiseptic Solids - <1% Flash Point F Viscosity - (#4 Ford 25 C) 10 seconds Stability - 1 year shelf life in an unopened container Density lbs./gallon (1.0 S.G.) VOC - N/A Packaging - 5-gallon plastic pail gallon plastic bottle Application Characteristics: Clarity - Negligible residue (dry) Coverage - 2,000 sq. ft./gal. (approx.) Leveling - N/A Percent Cured After 24 Hours - N/A Defoaming - N/A Maximum Cure - N/A Drying Time minutes Application Tools - Floor Prep Pad and buffer or autoscrubber

7 REPLAY MAINTENANCE CLEANER CLEANER FOR HARDWOOD FLOORS Environment, Health & Safety No alcohols No ammonia ph Neutral Non-hazardous What the Pros Know Preventative Maintenance will extend the life of your floor finish. Simple steps such as placing walk-off mats in door ways to keep out dirt and grit and avoiding excess moisture from tracked in water or leaks will prolong the life of your floor. Having a planned daily maintenance schedule of dry mopping or damp mopping over spills can help reduce overall labor costs. Periodic maintenance steps will be needed to keep the look and feel of the finish up to your standards. With this step, an autoscrubber or 175 rpm buffer with a white pad is used with the NewAge Replay Maintenance Cleaner to give a more thorough, deep cleansing. This will minimize the chance of contamination from damaging the floor and reducing overall labor costs. Technical Data Sheet Description A waterborne, environmentally responsible cleaner specifically formulated for use in the preparation of old wood sport floors, or for periodic maintenance to clean all polyurethane finished wood floors without leaving any residue. NewAge Replay Maintenance Cleaner is a concentrate, to be diluted with water according to directions. Recommended Use Aluminum oxide, ceramic, and other factory prefinished floors Basketball courts Volleyball courts Racquetball Badminton courts Multi-purpose gym and stage floors Aerobic floors Features Formulated for use on all waterborne or oil-modified polyurethane finishes For deep cleaning and periodic maintenance For spot cleaning of food spills and other stains Leaves no oily or waxy residue ph neutral Nonflammable ph neutral Formulated for use with all urethane finishes Virtually odorless No oily or waxy residues Excellent for spot & deep cleaning BILLERICA, MA CS /09

8 DIRECTIONS FOR USE: SHAKE WELL BEFORE USING. IMPORTANT! NEVER POUR CLEANER DIRECTLY ONTO THE FLOOR. FOR DAILY MAINTENANCE OF FINISHED FLOORS: 1. Sweep or dust mop (with untreated mop only) daily to remove dust, grit or other abrasive particles. 2. Lightly mist your clean mop head with diluted (1 part cleaner to 8 parts water) Replay Maintenance Cleaner Concentrate. Replace soiled mop covers as necessary. (Continued use of soiled covers will cause streaking.) 3. For spills or spots, damp wipe with Replay Maintenance Cleaner Concentrate diluted at the 1 to 8 ratio. NOTE: DO NOT USE ANY DUST MOP TREATMENTS. FOR PERIODIC MAINTENANCE OF FINISHED FLOORS: 1. Dilute 1 part Replay Maintenance Cleaner Concentrate to 8 parts water for a tacking solution. Tack with a well wrung-out cotton towel wrapped around a push broom. Be sure to clean towels regularly and change the solution as needed. 2. Shoe marks and scuffs can be removed by using a white pad and a low or variable-speed buffer (175 rpm) with a (1:8) solution of Replay Maintenance Cleaner Concentrate. Lightly mist the floor with the solution as you buff. Periodically clean or replace white pad. Continued use of soiled pads will cause streaking. 3. Make sure all residue from the white pad buffing/cleaning procedure is removed from floor surface by immediately tacking the surface with water dampened, well wrung-out cotton towels. 4. For deep cleaning dilute 1 part Replay Maintenance Cleaner Concentrate to 5 parts water to be used as a spray-buff solution with a white pad and a low or variable-speed buffer (175 rpm). STORAGE: FREEZE-THAW STABLE. Product should always be stored in a climate controlled environment. Do not store above 100 F. If frozen, allow product to thaw out at room temperature before applying. CLEAN-UP: Clean all tools and equipment with water. SPECIFICATIONS/PHYSICAL DATA: Physical Characteristics: Ingredients - Water ( ), anionic and nonionic surfactants (Proprietary), and glycol ether solvents (Proprietary). Color - Brilliant purple solution (wet) Gloss Level - N/A ph Odor - Non-offending Solids - 2% Flash Point - Non-flammable Viscosity - (#4 Ford 25 C) 10 seconds Stability - One year shelf life in unopened container Density lbs./gallon (1.01 S.G.) VOC - Does not exceed 3% Packaging - 5-gallon plastic pail gallon plastic bottle Application Characteristics: Clarity - Negligible residue (dry) Coverage - N/A Leveling - N/A Percent Cured After 24 Hours - N/A Defoaming - N/A Maximum Cure - N/A Drying Time minutes Application Tools - Varies with task; see label

9 OMU POLY 500/43 SPORT FLOOR FINISH Environment, Health & Safety Passes ASTM D for Slip Resistance (MFMA test procedure) Lower aromatic solvents than most competitors What the Pros Know Preventative Maintenance will extend the life of your floor finish. Simple steps such as placing walk-off mats in door ways to keep out dirt and grit and avoiding excess moisture from tracked in water or leaks will prolong the life of your floor. Having a planned daily maintenance schedule of dry mopping or damp mopping over spills can help reduce overall labor costs. Periodic maintenance steps will be needed to keep the look and feel of the finish up to your standards. With this step, an autoscrubber or 175 rpm buffer with a white pad is used with the NewAge Replay Maintenance Cleaner to give a more thorough, deep cleansing. This will minimize the chance of contamination from damaging the floor and reducing overall labor costs. OMU Poly 500/43 exceeds the minimum slip resistance requirements for floor finishes when tested in accordance with ASTM D (MFMA test procedure) Technical Data Sheet Description OMU Poly 500/43 is a premium quality, oil-modified polyurethane developed specifically for the wood sport floor industry. OMU Poly 500/43 provides an extremely tough, high build gloss finish with superior flow and leveling. Recommended Use Basketball courts Volleyball courts Racquetball Badminton courts Multi-purpose gym and stage Aerobic floors Features Provides a tough protective coat Provides excellent chemical resistance Superior flow and leveling Protects against perspiration and routine cleaning Light amber color enhances natural color of wood Easy to maintain Available in gloss Will adhere to most solvent-based and waterborne finishes after proper preparation, drying, and curing times Provides a tough protective coat Excellent chemical resistance Superior flow and leveling Easy to maintain BILLERICA, MA CS /09

10 DIRECTIONS FOR USE: BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS FOR THIS PRODUCT. Use directly from the can, do not thin. Non-photochemically reactive (not an ozone precursor). NewAge OMU Poly 500/43 Sport Floor Finish is a premium quality, oil-modified polyurethane developed specifically for the wood sport floor market. OMU Poly 500/43 provides an extremely tough, high build gloss finish with superior flow and leveling. ABRADE AND RECOAT EXISTING FLOORS: 1. Be sure floor is free from wax or oily residue. 2. Clean floor thoroughly with NewAge Replay Maintenance Cleaner and use NewAge Recoat Conditioner and Prep Cleaner system (see label for directions). 3. When recoating over other manufacturers finishes, check with manufacturer for abrading recommendations. 4. Vacuum thoroughly. 5. Tack with untreated dust mop or slightly water-dampened towel. 6. Apply 1-2 coats of a NewAge finish (see finish directions). Note: OMU Poly 500/43 will adhere to most finishes after proper preparation and dry times. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DE- TERMINE COMPATIBILITY AND ADHESION SANDING AND FINISHING NEW FLOORS: 1. Sand and prepare floor using MFMA-accepted methods. 2. Make your final cut with grit paper. Screen with grit screen. 3. Vacuum thoroughly. 4. Tack with mineral spirits. 5. Apply sealer and paint using MFMA-accepted methods then apply finish system (see finish directions). INTERCOAT ABRASION FOR FLOORS WITH GAME LINES: Apply game lines over either the sealer coat or the first coat of finish. Before applying game lines, abrade with a Floor Prep Pad (FPP) or 120-grit screen and vacuum and tack thoroughly. BEFORE APPLYING GAME LINES, ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY AND ADHESION. After applying game lines, abrade dry game lines with a FPP or 120-grit screen. If coating or applying game lines more than 24 hours after abrading, floor must be re-abraded to ensure adhesion of finish. Always vacuum and tack thoroughly after abrading. Apply finish coat. INTERCOAT ABRASION FOR FLOORS WITHOUT GAME LINES: Abrade between all sealer and finish coats of OMU Poly 500/43 to ensure adhesion. Always vacuum and tack thoroughly after abrading. FINISH INSTRUCTIONS: REMOVE LID AND STIR WELL WITH A PROPER STIRRING DEVICE BEFORE USING. 1. Apply 1 coat of sealer according to label directions, followed by 2 coats of OMU Poly 500/ Apply OMU Poly 500/43 with a clean NewAge Heavyweight (HW) Applicator. Go with the grain of the wood applying a thin, uniform coat. 3. Ensure coverage rate of sq. ft. per gallon is maintained; heavier applications will increase dry times. 4. Feather out all applicator marks, turn marks, puddles, etc. 5. Allow your first coat to dry thoroughly, 8 hours under ideal conditions F and 40-60% relative humidity. High humidity and/or low temperature conditions will extend the dry time, while increased ventilation and airflow will reduce dry time. 6. For proper adhesion, abrade with a FPP between coats of finish. 7. Always vacuum and tack with water thoroughly after abrading. Allow final coat to dry a minimum of 72 hours before use. NOTE: OMU Poly 500/43 is not recommended over shellac, lacquer sanding sealers, fillers or stains containing stearates. Oil-modified finishes will have a slight ambering effect over light-colored surfaces. STORAGE: Product should always be stored in a climate controlled environment. Do not store above 100 F. DRY TIME/CURING: With conditions of 65 to 80 F and 40 to 60% humidity this finish will dry in 8 hours. The curing process takes approximately 14 days. The floor may be walked on after 24 hours, but the floor is susceptible to scuffing or marring prior to completion of the curing time. Do not replace athletic or walk-off mats until finish is fully cured. Do not clean with water or detergent during the curing process. MAINTENANCE: Place walk-off mats at all entrance doorways to keep out excessive dirt and grit. See NewAge Replay Maintenance Cleaner instructions for cleaning and maintenance information CLEAN-UP: Clean application tools and equipment with mineral spirits. SPECIFICATIONS/PHYSICAL DATA: Physical Characteristics: Ingredients - Oil-modified polyurethane resin (Proprietary), mineral spirits ( ), driers (Proprietary). Color - Light amber Gloss Level - (60 ) 90+ ph - N/A Odor - Mineral spirits Solids - 43% Flash Point F (PMCC) Viscosity - (#4 Ford 25 C) approx seconds Stability - One year shelf life in unopened container Density lbs./gallon (0.9 S.G.) VOC - Does not exceed 500 grams per liter (4.2 pounds per gallon) Packaging - 5-gallon pail Application Characteristics: Clarity - Clear when dry Coverage sq. ft. per gallon Leveling - Excellent Percent Cured After 24 Hours - 50% Defoaming - Excellent Maximum Cure - 2 weeks Drying Time - 8 hours Application Tools - NewAge Heavyweight (HW) Applicator, brush, lambswool applicator

11 OMU POLY 450/50 SPORT FLOOR FINISH Environment, Health & Safety Passes ASTM D for Slip Resistance (MFMA test procedure) Lower aromatic solvents than most competitors What the Pros Know Preventative Maintenance will extend the life of your floor finish. Simple steps such as placing walk-off mats in door ways to keep out dirt and grit and avoiding excess moisture from tracked in water or leaks will prolong the life of your floor. Having a planned daily maintenance schedule of dry mopping or damp mopping over spills can help reduce overall labor costs. Periodic maintenance steps will be needed to keep the look and feel of the finish up to your standards. With this step, an autoscrubber or 175 rpm buffer with a white pad is used with the NewAge Replay Maintenance Cleaner to give a more thorough, deep cleansing. This will minimize the chance of contamination from damaging the floor and reducing overall labor costs. OMU Poly 450/50 exceeds the minimum slip resistance requirements for floor finishes when tested in accordance with ASTM D (MFMA test procedure) Technical Data Sheet Description NewAge OMU Poly 450/50 is a premium quality, oil-modified polyurethane developed specifically for the wood sport floor market. OMU Poly 450/50 provides an extremely tough, high build gloss finish with excellent chemical resistance, protecting against perspiration and routine cleaning. Recommended Use Basketball courts Volleyball courts Racquetball Badminton courts Multi-purpose gym and stage Aerobic floors Features High solids, oil-modified polyurethane Provides a tough protective coat Provides excellent chemical resistance Protects against perspiration and routine cleaning Light amber color enhances natural color of wood Easy to maintain Self-leveling Available in gloss Will adhere to most solvent-based and waterborne finishes after proper preparation, drying, and curing times High Solids Provides a tough protective coat Excellent chemical resistance Self-leveling Easy to maintain BILLERICA, MA CS /09

12 DIRECTIONS FOR USE: BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS FOR THIS PRODUCT. Use directly from the can, do not thin. Non-photochemically reactive (not an ozone precursor). NewAge OMU Poly 450/50 Sport Floor Finish is a premium quality, oil-modified polyurethane developed specifically for the wood sport floor market. For new installation of sport floors, use only in structures with humidity and temperature controls. DO NOT USE over channel and clip floor systems in environments not controlled for temperature and humidity. ABRADE AND RECOAT EXISTING FLOORS: 1. Be sure floor is free from wax or oily residue. 2. Clean floor thoroughly with NewAge Replay Maintenance Cleaner and use NewAge Recoat Conditioner and Prep Cleaner system (see label for directions). 3. When recoating over other manufacturers finishes, check with manufacturer for abrading recommendations. 4. Vacuum thoroughly. 5. Tack with untreated dust mop or slightly water-dampened towel. 6. Apply 1-2 coats of a NewAge finish (see finish directions). Note: OMU Poly 450/50 will adhere to most finishes after proper preparation and dry times. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY. SANDING AND FINISHING NEW FLOORS: 1. Sand and prepare floor using MFMA-accepted methods. 2. Make your final cut with grit paper. Screen with grit screen. 3. Vacuum thoroughly. 4. Tack with mineral spirits. 5. Apply sealer and paint using MFMA-accepted methods then apply finish system (see finish directions). INTERCOAT ABRASION FOR FLOORS WITH GAME LINES: Apply game lines over either the sealer coat or the first coat of finish. Before applying game lines, abrade with a Floor Prep Pad (FPP) or 120-grit screen and vacuum and tack thoroughly. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY AND ADHESION. After applying game lines, abrade dry game lines with a FPP or 120-grit screen. If coating or applying game lines more than 24 hours after abrading, floor must be re-abraded to ensure adhesion of finish. Always vacuum and tack thoroughly after abrading. Apply finish coat. INTERCOAT ABRASION FOR FLOORS WITHOUT GAME LINES: Abrade between all sealer and finish coats of OMU Poly 450/50 to ensure adhesion. Always vacuum and tack thoroughly after abrading. FINISH INSTRUCTIONS: REMOVE LID AND STIR WELL WITH A PROPER STIRRING DEVICE BEFORE USING. 1. Apply 1 coat of sealer according to label directions, followed by 2 coats of OMU Poly 450/ Apply OMU Poly 450/50 with a clean NewAge Heavyweight (HW) Applicator. Go with the grain of the wood applying a thin, uniform coat. 3. Ensure coverage rate of 500 sq. ft. per gallon is maintained; heavier applications will increase dry times. 4. Feather out all applicator marks, turn marks, puddles, etc. 5. Allow your first coat to dry thoroughly, 8-12 hours under ideal conditions (65-80 F and 40-60% relative humidity). High humidity and/or low temperature conditions will extend the dry time, while increased ventilation and airflow will reduce dry time. 6. For proper adhesion, abrade with a FPP between coats of finish. 7. Always vacuum and tack with water thoroughly after abrading. Allow final coat to dry a minimum of 72 hours before use. NOTE: OMU Poly 450/50 is not recommended over shellac, lacquer sanding sealers, fillers or stains containing stearates. Oil-modified finishes will have a slight ambering effect over light-colored surfaces. STORAGE: Product should always be stored in a climate controlled environment. Do not store above 100 F. DRY TIME/CURING: With conditions of 65 to 80 F and 40 to 60% humidity this finish will dry in 8-12 hours. The curing process takes approximately 14 days. The floor may be walked on after 24 hours, but the floor is susceptible to scuffing or marring prior to completion of the curing time. Do not replace athletic or walk-off mats until finish is fully cured. Do not clean with water or detergent during the curing process. MAINTENANCE: Place walk-off mats at all entrance doorways to keep out excessive dirt and grit. See NewAge Replay Maintenance Cleaner instructions for cleaning and maintenance information. CLEAN-UP: Clean application tools and equipment with mineral spirits. STORAGE: Product should always be stored in a climate controlled environment. Do not store above 100 F. SPECIFICATIONS/PHYSICAL DATA: Physical Characteristics: Ingredients - Oil-modified polyurethane resin (Proprietary), mineral spirits ( ), driers (Proprietary). Color - Light amber Gloss Level - (60 ) 90+ ph - N/A Odor - Mineral spirits Solids - 50% Flash Point F (PMCC) Viscosity - (#4 Ford 25 C) approx seconds Stability - One year shelf life in unopened container Density lbs./gallon (.90 S.G.) VOC - Does not exceed 450 grams per liter (3.8 pounds per gallon) Packaging - 5-gallon pail Application Characteristics: Clarity - Clear when dry Coverage sq. ft. per gallon Leveling - Good Percent Cured After 24 Hours - 50% Defoaming - Excellent Maximum Cure - 2 weeks Drying Time hours Application Tools - NewAge Heavyweight (HW) Applicator, brush, lambswool applicator

13 OMU POLY 350/55 SPORT FLOOR FINISH Environment, Health & Safety Passes ASTM D for Slip Resistance (MFMA test procedure) Lower aromatic solvents than most competitors VOC compliant (except for SCAQMD) What the Pros Know Preventative Maintenance will extend the life of your floor finish. Simple steps such as placing walk-off mats in door ways to keep out dirt and grit and avoiding excess moisture from tracked in water or leaks will prolong the life of your floor. Having a planned daily maintenance schedule of dry mopping or damp mopping over spills can help reduce overall labor costs. Periodic maintenance steps will be needed to keep the look and feel of the finish up to your standards. With this step, an autoscrubber or 175 rpm buffer with a white pad is used with the NewAge Replay Maintenance Cleaner to give a more thorough, deep cleansing. This will minimize the chance of contamination from damaging the floor and reducing overall labor costs. OMU Poly 350/55 exceeds the minimum slip resistance requirements for floor finishes when tested in accordance with ASTM D (MFMA test procedure) Technical Data Sheet Description NewAge OMU Poly 350/55 is a premium quality, high solids oil-modified polyurethane developed specifically for the wood sport floor market. OMU Poly 350/55 is low VOC, and provides an extremely tough, high build gloss finish with excellent chemical resistance, protecting against perspiration and routine cleaning. OMU Poly 350/55 is specially formulated to meet all federal and state clean air quality standards (except for SCAQMD). Recommended Use Basketball courts Volleyball courts Racquetball Badminton courts Multi-purpose gym and stage Aerobic floors Features High solids, oil-modified polyurethane Provides a tough protective coat Provides excellent chemical resistance Light amber color enhances natural color of wood Easy to maintain Self-leveling Available in high gloss Will adhere to most solvent-based and waterborne finishes after proper preparation, drying, and curing times High Solids Provides a tough protective coat Excellent chemical resistance Self-leveling Easy to maintain 350 VOC BILLERICA, MA CS /09

14 DIRECTIONS FOR USE: BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS FOR THIS PRODUCT. Use directly from the can, do not thin. Non-photochemically reactive (not an ozone precursor). NewAge OMU Poly 350/55 Sport Floor Finish is a premium quality, high solids oil-modified polyurethane developed specifically for the wood sport floor market. OMU POLY 350/55 is low VOC, and provides an extremely tough, high build gloss finish with excellent chemical resistance, protecting against perspiration and routine cleaning. ABRADE AND RECOAT EXISTING FLOORS: 1. Be sure floor is free from wax or oily residue. 2. Clean floor thoroughly with NewAge Replay Maintenance Cleaner and use NewAge Recoat Conditioner and Prep Cleaner system (see label for directions). 3. When recoating over other manufacturers finishes, check with manufacturer for abrading recommendations. 4. Vacuum thoroughly. 5. Tack with untreated dust mop or slightly water-dampened towel. 6. Apply 1-2 coats of a NewAge finish (see finish directions). NOTE: OMU Poly 350/55 will adhere to most finishes after proper preparation and dry times. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY. SANDING AND FINISHING: 1. Sand and prepare floor using MFMA-accepted methods. 2. Make your final cut with grit paper. Screen with grit screen. 3. Vacuum thoroughly. 4. Tack with mineral spirits. 5. Apply sealer and paint using MFMA-accepted methods then apply finish system (see finish directions). INTERCOAT ABRASION FOR FLOORS WITH GAME LINES: Apply game lines over the sealer coat. Before applying game lines, abrade with a Floor Prep Pad (FPP) or 120-grit screen and vacuum and tack thoroughly. BEFORE APPLYING GAME LINES, ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY AND ADHESION. After applying game lines, abrade dry game lines with a FPP or 120-grit screen. If coating or applying game lines more than 24 hours after abrading, floor must be re-abraded to ensure adhesion of finish. Always vacuum and tack thoroughly after abrading. Apply finish coat. INTERCOAT ABRASION FOR FLOORS WITHOUT GAME LINES: Abrade between all sealer and finish coats of OMU Poly 350/55 to ensure adhesion. Always vacuum and tack thoroughly after abrading. FINISH INSTRUCTIONS: REMOVE LID AND STIR WELL WITH A PROPER STIRRING DEVICE BEFORE USING. 1. Apply 1 coat of sealer according to label directions, followed by 2 coats of OMU Poly 350/ Apply OMU Poly 350/55 with a clean NewAge Heavyweight (HW) Applicator. Go with the grain of the wood applying a thin, uniform coat. 3. Ensure coverage rate of sq. ft. per gallon is maintained; heavier applications will increase dry times. 4. Feather out all applicator marks, turn marks, puddles, etc. 5. Allow your first coat to dry thoroughly, 18 hours under ideal conditions (65-80 F and 40-60% relative humidity). High humidity and/or low temperature conditions will extend the dry time, while increased ventilation and airflow will reduce dry time. 6. For proper adhesion, abrade with a FPP between coats of finish. 7. Always vacuum and tack with water thoroughly after abrading. Allow final coat to dry a minimum of 72 hours before use. NOTE: OMU Poly 350/55 is not recommended over shellac, lacquer sanding sealers, fillers or stains containing stearates. Oil-modified finishes will have a slight ambering effect over light-colored surfaces. STORAGE: Product should always be stored in a climate controlled environment. Do not store above 100 F. DRY TIME/CURING: With conditions of 65 to 80 F and 40 to 60% humidity this finish will dry in 18 hours. The curing process takes approximately 14 days. The floor may be walked on after 24 hours, but the floor is susceptible to scuffing or marring prior to completion of the curing time. Do not replace athletic or walk-off mats until finish is fully cured. Do not clean with water or detergent during the curing process. MAINTENANCE: Place walk-off mats at all entrance doorways to keep out excessive dirt and grit. See NewAge Replay Maintenance Cleaner instructions for cleaning and maintenance information. CLEAN-UP: Clean application tools and equipment with mineral spirits. SPECIFICATIONS/PHYSICAL DATA: Physical Characteristics: Ingredients - Oil-modified polyurethane resin (Proprietary), mineral spirits ( and ), polysiloxane ( ), linseed oil ( ). Color - Amber Gloss Level - (60 ) 90+ ph - N/A Odor - Mineral spirits Solids % Flash Point F (PMCC) Viscosity - (#4 Ford 25 C) approx seconds Stability - One year shelf life in unopened container Density lbs./gallon (.91 S.G.) VOC - Does not exceed 350 grams per liter (2.9 pounds per gallon) Packaging - 5-gallon pail Application Characteristics: Clarity - Clear when dry Coverage sq. ft. per gallon Leveling - Good Percent Cured After 24 Hours - 50% Defoaming - Excellent Maximum Cure - 2 weeks Drying Time - 18 hours (based on recommended coverage rate, under ideal conditions) Application Tools - NewAge Heavyweight (HW) Applicator