Shop Drawings: Show fabrication and installation details for signs.

Transcription

1 SECTION SIGNAGE PART 1 - GENERAL RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section. SUMMARY This Section includes the following: 1. Panel signs (interior signage). Related Sections include the following: 1. Division 1 Section "Temporary Facilities and Controls" for temporary Project identification signs and for temporary information and directional signs. 2. Division I 5 Section "Mechanical Identification" for labels, tags, and nameplates for mechanical equipment. 3. Division 16 Section "Electrical Identification" for labels, tags, and nameplates for electrical equipment. 4. Division 16 Section "Interior Lighting" for illuminated Exit signs. DEFINITIONS ADA-ABA Accessibility Guidelines: U.S. Architectural & Transportation Barriers Compliance Board's "Americans with Disabilities Act (ADA) Accessibility Guidelines for Buildings and Facilities; Architectural Barriers Act (ABA) Accessibility Guidelines." SUBMITTALS Product Data: For each type of product indicated. Shop Drawings: Show fabrication and installation details for signs. 1. Show sign mounting heights, locations of supplementary supports to be provided by others, and accessories. Samples for Initial Selection: Manufacturer's color charts consisting of actual units or sections of units showing the full range of colors available for the following: 1. Acrylic sheet. 2. Polycarbonate sheet. 3. Fiberglass sheet. 4. Die-cut vinyl characters and graphic symbols. Samples for Verification: For each of the following products and for the full range of color, texture, and sign material indicated, of sizes indicated:

2 1. Dimensional Characters: Full-size Samples of each type of dimensional character (letter, number, and graphic element). 2. Acrylic Sheet: 8 by 10 inches for each color required. Sign Schedule: Use designations as directed by OwnerIArchitect. See sign schedule at end of Section for signage to be furnished and installed under base bid. Warranty: Special warranty specified in this Section. QUALITY ASSURANCE Fabricator Qualifications: Shop that employs skilled workers who custom-fabricate products similar to those required for this Project and whose products have a record of successful inservice performance. Source Limitations for Signs: Obtain each sign type indicated from one source from a single manufacturer. Regulatory Requirements: Guidelines. Comply with applicable provisions in ADA-ABA Accessibility PROJECT CONDITIONS Weather Limitations: Proceed with installation only when weather conditions permit installation of signs in exterior locations to be performed according to manufacturers' written instructions and warranty requirements. Field Measurements: Verify recess openings by field measurements before fabrication and indicate measurements on Shop Drawings. COORDINATION Coordinate placement of anchorage devices with templates for installing signs. WARRANTY Special Warranty: Manufacturer's standard form in which manufacturer agrees to repair or replace components of signs that fail in materials or workmanship within specified warranty period. 1. Failures include, but are not limited to, the following: a. Deterioration of metal finishes beyond normal weathering. 2. Warranty Period: Five years from date of Substantial Completion.

3 PART 2 - PRODUCTS 2.1 MATERIALS A. Acrylic Sheet: ASTM D 4802, Category A-1 (cell-cast sheet), Type UVA (UV absorbing). B. Polycarbonate Sheet: Of thickness indicated, manufactured by extrusion process, coated on both surfaces with abrasion-resistant coating: 1. Impact Resistance: 16 ft-lbflin. per ASTM D 256, Method A. 2. Tensile Strength: 9000 Ibflsq. in. per ASTM D Flexural Modulus of Elasticity: 340,000 Ibflsq. in. per ASTM D Heat Deflection: 265 deg F at 264 Ibflsq. in. per ASTM D Abrasion Resistance: 1.5 percent maximum haze increase for 100 revolutions of a Taber abraser with a load of 500 g per ASTM D PANEL SIGNS A. Available Manufacturers: Subject to compliance with requirements, manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following: B. Comparable product by one of the following: ACE Sign Systems, Inc. Advance Corporation; Braille-Tac Division. Allen Industries Architectural Signage Allenite Signs; Allen Marking Products, Inc. APCO Graphics, lnc. ASI-Modulex, Inc. Best Sign Systems Inc. Bunting Graphics, Inc. Fossil Industries, Inc. Gemini Incorporated. Grimco, Inc. Innerface Sign Systems, Inc. lnpro Corporation Matthews International Corporation; Bronze Division. Mills Manufacturing Company. Mohawk Sign Systems. Nelson-Harkins Industries. Seton Identification Products. Signature Signs, Incorporated. Supersine Company (The) C. Interior Panel Signs: Provide smooth sign panel surfaces constructed to remain flat under installed conditions within a tolerance of plus or minus 1/16 inch measured diagonally from corner to corner, complying with the following requirements: 1. Acrylic Sheet: inch thick. 2. Edge Condition: Bullnose. 3. Corner Condition: Square. 4. Mounting: Unframed. a. Manufacturer's standard anchors for substrates encountered.

4 5. Color: As selected by Architect from manufacturer's full range. 6. Tactile Characters: Characters and Grade 2 Braille raised 1/32 inch above surface with contrasting colors. 2.3 ACCESSORIES A. Anchors and Inserts: Provide nonferrous-metal or hot-dip galvanized anchors and inserts for exterior installations and elsewhere as required for corrosion resistance. Use toothed steel or lead expansion-bolt devices for drilled-in-place anchors. Furnish inserts, as required, to be set into concrete or masonry work. 2.4 FABRICATION A. General: Provide manufacturer's standard signs of configurations indicated. 1. Welded Connections: Comply with AWS standards for recommended practices in shop welding. Provide welds behind finished surfaces without distortion or discoloration of exposed side. Clean exposed welded surfaces of welding flux and dress exposed and contact surfaces. 2. Mill joints to tight, hairline fit. Form joints exposed to weather to exclude water penetration. 3. Preassemble signs in the shop to greatest extent possible. Disassemble signs only as necessary for shipping and handling limitations. Clearly mark units for reassembly and installation, in location not exposed to view after final assembly. 4. Conceal fasteners if possible; otherwise, locate fasteners where they will be inconspicuous. 2.5 FINISHES, GENERAL A. Comply with NAAMM's "Metal Finishes Manual for Architectural and Metal Products" for recommendations for applying and designating finishes. B. Protect mechanical finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping. C. Appearance of Finished Work: Variations in appearance of abutting or adjacent pieces are acceptable if they are within one-half of the range of approved Samples. Noticeable variations in the same piece are not acceptable. Variations in appearance of other components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast. 2.6 ACRYLIC SHEET FINISHES A. Colored Coatings for Acrylic Sheet: For copy and background colors, provide colored coatings, including inks, dyes, and paints, that are recommended by acrylic manufacturers for optimum adherence to acrylic surface and that are UV and water resistant for five years for application intended.

5 PART 3 - EXECUTION EXAMINATION Examine substrates, areas, and conditions, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of work. Verify that items are sized and located to accommodate signs. Proceed with installation only after unsatisfactory conditions have been corrected. INSTALLATION Locate signs and accessories where indicated, using mounting methods of types described and complying with manufacturer's written instructions. 1. Install signs level, plumb, and at heights indicated, with sign surfaces free of distortion and other defects in appearance. 2. Interior Wall Signs: Install signs on walls adjacent to latch side of door where applicable. Where not indicated or possible, such as double doors, install signs on nearest adjacent walls. Locate to allow approach within 3 inches of sign without encountering protruding objects or standing within swing of door. Wall-Mounted Signs: Comply with sign manufacturer's written instructions except where more stringent requirements apply. 1. Two-Face Tape: Mount signs to smooth, nonporous surfaces. Do not use this method for vinyl-covered or rough surfaces. 2. Shim Plate Mounting: Provide 118-inch- thick, concealed aluminum shim plates with predrilled and countersunk holes, at locations indicated, and where other mounting methods are not practicable. Attach plate with fasteners and anchors suitable for secure attachment to substrate. Attach panel signs to plate using method specified above. 3. Mechanical Fasteners: Use nonremovable mechanical fasteners placed through predrilled holes. Attach signs with fasteners and anchors suitable for secure attachment to substrate as recommended in writing by sign manufacturer. 4. Signs Mounted on Glass: Provide matching opaque plate on opposite side of glass to conceal mounting materials. CLEANING AND PROTECTION After installation, clean soiled sign surfaces according to manufacturer's written instructions. Protect signs from damage until acceptance by Owner. SIGN SCHEDULE A. Furnish and install one (1) 8"x8" ADA accessible sign with graphic designation and Braille characters at the following locations: 1) MEN'S RESTROOM (wall outside door 107-A) 2) WOMEN'S RESTROOM (wall outside door 109-A)

6 B. Furnish and install one (1) 3"x5" ADA accessible sign with Braille characters and the following designation listed below at the following locations: 1) EXIT (wall at doors 101-A and 103-A) C. Furnish and install one (1) 8"x8" ADA accessible sign with the following designation listed below. Location to be determined in field by OwnerlArchitect. 1) MAXIMUM OCCUPANCY: 80 OCCUPANTS END OF SECTION 10431

7 SECTION FIRE-PROTECTION SPECIALTIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section. 1.2 SUMMARY A. This Section includes the following: 1. Portable fire extinguishers. 2. Fire-protection cabinets for portable fire extinguishers. 1.3 SUBMITTALS A. Product Data: Include construction details, material descriptions, dimensions of individual components and profiles, and finishes for fire-protection cabinets. 1. Fire Extinguishers: Include rating and classification. 2. Fire-Protection Cabinets: Include roughing-in dimensions, details showing mounting methods, relationships of box and trim to surrounding construction, door hardware, cabinet type, trim style, and panel style. B. Maintenance Data: For fire extinguishers and fire-protection cabinets to include in maintenance manuals. 1.4 QUALITY ASSURANCE A. Source Limitations: Obtain fire extinguishers and fire-protection cabinets through one source from a single manufacturer. 6. NFPA Compliance: Fabricate and label fire extinguishers to comply with NFPA 10, "Portable Fire Extinguishers." C. Fire Extinguishers: Listed and labeled for type, rating, and classification by an independent testing agency acceptable to authorities having jurisdiction. 1.5 COORDINATION A. Coordinate size of fire-protection cabinets to ensure that type and capacity of fire extinguishers indicated are accommodated. FIRE-PROTECTION SPECIALTIES

8 1.6 WARRANTY A. Special Warranty: Manufacturer's standard form in which manufacturer agrees to repair or replace components of portable fire extinguishers that fail in materials or workmanship within specified warranty period. 1. Failures include, but are not limited to, the following: a. Failure of hydrostatic test according to NFPA 10. b. Faulty operation of valves or release levers. 2. Warranty Period: Six years from date of Substantial Completion. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. In other Part 2 articles where titles below introduce lists, the following requirements apply to product selection: 1. Available Manufacturers: Subject to compliance with requirements, manufacturers offering products that may be incorporated into the Work include, but are not limited to, manufacturers specified. 2.2 MATERIALS A. Cold-Rolled Steel Sheet: ASTM A 1008lA 1008M, Commercial Steel (CS), Type B. B. Tempered Float Glass: ASTM C 1048, Kind FT, Condition A, Type I, Quality q3, 3 mm thick, Class 1 (clear). 2.3 PORTABLE FIRE EXTINGUISHERS A. Available Manufacturers: 1. JL Industries, Inc. 2. Kidde Fyrnetics. 3. Larsen's Manufacturing Company. B. General: Provide fire extinguishers of type, size, and capacity for each fire-protection cabinet and mounting bracket indicated. 1. Valves: Manufacturer's standard. 2. Handles and Levers: Manufacturer's standard. 3. Instruction Labels: Include pictorial marking system complying with NFPAIO, Appendix B. C. Multipurpose Dry-Chemical Type in Steel Container FE-1: UL-rated 4-A:60-B:C, 10-lb nominal capacity, with monoammonium phosphate-based dry chemical in enameled-steel container. FIRE-PROTECTION SPECIALTIES

9 FIRE-PROTECTION CABINET Available Manufacturers: 1. JL Industries, Inc. 2. Kidde Fyrnetics. 3. Larsen's Manufacturing Company. Cabinet Type: Suitable for fire extinguisher Cabinet Construction: Rated per adjacent wall construction. Cabinet Material: Enameled-steel sheet. 1. Shelf: Same metal and finish as cabinet. Semirecessed Cabinet: Cabinet box partially recessed in walls of shallow depth to suit style of trim indicated; with one-piece combination trim and perimeter door frame overlapping surrounding wall surface with exposed trim face and wall return at outer edge (backbend). 1. Rolled-Edge Trim: inch backbend depth. Cabinet Trim Material: Steel sheet. Door Material: Steel sheet. Door Style: Fully glazed panel with frame. Door Glazing: Tempered float glass (clear). Door Hardware: Manufacturer's standard door-operating hardware of proper type for cabinet type, trim style, and door material and style indicated. 1. Provide projecting door pull and friction latch. 2. Provide continuous hinge, of same material and finish as trim, or concealed hinge permitting door to open 180 degrees. Accessories: 1. Mounting Bracket: Manufacturer's standard steel, designed to secure fire extinguisher to fire-protection cabinet, of sizes required for types and capacities of fire extinguishers indicated, with plated or baked-enamel finish. Finishes: I. Manufacturer's standard baked-enamel paint for the following: a. Exterior of cabinet, door, and trim, except for those surfaces indicated to receive another finish. b. Interior of cabinet and door. 2. Steel: Baked enamel, color and texture as selected by Architect from manufacturer's full range. FIRE-PROTECTION SPECIALTIES

10 FABRICATION Fire-Protection Cabinets: Provide manufacturer's standard box (tub), with trim, frame, door, and hardware to suit cabinet type, trim style, and door style indicated. 1. Weld joints and grind smooth. 2. Construct fire-rated cabinets with double walls fabricated from inch- thick, coldrolled steel sheet lined with minimum 518-inch- thick, fire-barrier material. a. Provide factory-drilled mounting holes. Cabinet Doors: Fabricate doors according to manufacturer's standards, from materials indicated and coordinated with cabinet types and trim styles selected. 1. Fabricate door frames with tubular stiles and rails and hollow-metal design, minimum 112 inch thick. 2. Miter and weld perimeter door frames. Cabinet Trim: Fabricate cabinet trim in one piece with corners mitered, welded, and ground smooth. FINISHES, GENERAL Comply with NAAMM's "Metal Finishes Manual for Architectural and Metal Products" for recommendations for applying and designating finishes. Protect mechanical finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping. Finish fire-protection cabinets after assembly. Appearance of Finished Work: Variations in appearance of abutting or adjacent pieces are acceptable if they are within one-half of the range of approved Samples. Noticeable variations in the same piece are not acceptable. Variations in appearance of other components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast. STEEL FINISHES Surface Preparation: Clean surfaces of dirt, oil, grease, mill scale, rust, and other contaminants that could impair paint bond using manufacturer's standard methods. Baked-Enamel Finish: Immediately after cleaning and pretreating, apply manufacturer's standard two-coat, baked-enamel finish consisting of prime coat and thermosetting topcoat. Comply with paint manufacturer's written instructions for applying and baking to achieve a minimum dry film thickness of 2 mils. FIRE-PROTECTION SPECIALTIES

11 PART 3 - EXECUTION 3.1 EXAMINATION A. Examine walls and partitions for suitable framing depth and blocking where semirecessed cabinets will be installed. B. Examine fire extinguishers for proper charging and tagging. 1. Remove and replace damaged, defective, or undercharged units. C. Proceed with installation only after unsatisfactory conditions have been corrected. 3.2 PREPARATION A. Prepare recesses for semirecessed fire-protection cabinets as required by type and size of cabinet and trim style. 3.3 INSTALLATION A. General: Install fire-protection specialties in locations and at mounting heights indicated or, if not indicated, at heights indicated below. 1. Fire-Protection Cabinets: 40 inches above finished floor to center of cabinet handle. B. Fire-Protection Cabinets: Fasten fire-protection cabinets to structure, square and plumb. 1. Unless otherwise indicated, provide recessed fire-protection cabinets. If wall thickness is not adequate for recessed cabinets, provide semirecessed fire-protection cabinets. 2. Provide inside latch and lock for break-glass panels. 3. Fasten mounting brackets to inside surface of fire-protection cabinets, square and plumb. 3.4 ADJUSTING AND CLEANING A. Remove temporary protective coverings and strippable films, if any, as fire-protection specialties are installed, unless otherwise indicated in manufacturer's written installation instructions. B. Adjust fire-protection cabinet doors to operate easily without binding. Verify that integral locking devices operate properly. C. On completion of fire-protection cabinet installation, clean interior and exterior surfaces as recommended by manufacturer. D. Touch up marred finishes, or replace fire-protection cabinets that cannot be restored to factoryfinished appearance. Use only materials and procedures recommended or furnished by fireprotection cabinet manufacturer. E. Replace fire-protection cabinets that have been damaged or have deteriorated beyond successful repair by finish touchup or similar minor repair procedures. END OF SECTION FIRE-PROTECTION SPECIALTIES

12

13 SECTION TOILET AND BATH ACCESSORIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section. 1.2 SUMMARY A. This Section includes the following: 1. Toilet accessories. 1.3 SUBMITTALS A. Product Data: For each type of product indicated. Include the following: 1 Construction details and dimensions. 2. Anchoring and mounting requirements, including requirements for cutouts in other work and substrate preparation. 3. Material and finish descriptions. 4. Features that will be included for Project. 5. Manufacturer's warranty. B. Product Schedule: Indicating types, quantities, sizes, and installation locations by room of each accessory required. 1. Identify locations using room designations indicated on Drawings. 2. Identify products using designations indicated on Drawings. C. Maintenance Data: For toilet and bath accessories to include in maintenance manuals. 1.4 QUALITY ASSURANCE A. Source Limitations: For products listed together in the same articles in Part 2, provide products of same manufacturer unless otherwise approved by Architect. 1.5 COORDINATION A. Coordinate accessory locations with other work to prevent interference with clearances required for access by people with disabilities, and for proper installation, adjustment, operation, cleaning, and servicing of accessories. B. Deliver inserts and anchoring devices set into concrete or masonry as required to prevent delaying the Work. TOILET AND BATH ACCESSORIES

14 1.6 WARRANTY A. Special Mirror Warranty: Manufacturer's standard form in which manufacturer agrees to replace mirrors that develop visible silver spoilage defects and that fail in materials or workmanship within specified warranty period. 1. Warranty Period: 15 years from date of Substantial Completion. PART 2 - PRODUCTS 2.1 MATERIALS A. Stainless Steel: ASTM A 666, Type 304, inch minimum nominal thickness, unless otherwise indicated. B. Brass: ASTM B 19 flat products; ASTM B 16, rods, shapes, forgings, and flat products with finished edges; or ASTM B 30, castings. C. Steel Sheet: ASTM A 1008lA 1008M, Designation CS (cold rolled, commercial steel), inch minimum nominal thickness. D. Galvanized Steel Sheet: ASTM A 653lA 653M, with G60 hot-dip zinc coating. E. Galvanized Steel Mounting Devices: ASTM A 153lA 153M, hot-dip galvanized after fabrication. F. Fasteners: Screws, bolts, and other devices of same material as accessory unit and tamperand-theft resistant where exposed, and of galvanized steel where concealed. G. Chrome Plating: ASTM B 456, Service Condition Number SC 2 (moderate service). H. Mirrors: ASTM C 1503, Mirror Glazing Quality, clear-glass mirrors, nominal 6.0 mm thick. 2.2 TOILET ACCESSORIES A. Basis-of-Design Product: The design for accessories is based on products indicated. Subject to compliance with requirements, provide the named product or a comparable product by one of the following: 1. A & J Washroom Accessories, Inc. 2. American Specialties, Inc. 3. Bobrick Washroom Equipment, Inc. 4. Bradley Corporation. B. Grab Bar: 1. Basis-of-Design Product: Bobrick; Series B Mounting: Flanges with concealed fasteners. 3. Material: Stainless steel, 0.05 inch (18 guage) thick. a. Finish: Smooth, No. 4, satin finish. 4. Outside Diameter: inches. TOILET AND BATH ACCESSORIES

15 5. Configuration and Length: As indicated on Drawings. C. Mirror Unit (ADA): 1. Basis-of-Design Product: Bobrick; Series: B Frame: Stainless-steel channel. a. Corners: Welded and ground smooth. 3. Hangers: Produce rigid, tamper- and theft-resistant installation, using method indicated below. a. One-piece, galvanized steel, wall-hanger device with spring-action locking mechanism to hold mirror unit in position with no exposed screws or bolts. 4. Size: As indicated on Drawings. D. Toilet Tissue (Roll) Dispenser: 1. Basis-of-Design Product: Bobrick;: B Description: Single dispenser. 3. Mounting: Surface mounted. 4. Operation: Tissue rolls are loaded on spindle. 5. Capacity: Designed for 5 % -inch- diameter tissue rolls. 6. Material and Finish: Stainless steel, No. 4 finish (satin). E. Combination Towel (Folded) DispenserNVaste Receptacle: 1. Basis-of-Design Product: Bobrick; B Description: Combination unit for dispensing C-fold or multifold towels, with removable waste receptacle. 3. Mounting: Surface mounted. 4. Minimum Towel-Dispenser Capacity: 350 C-fold or 475 multifold paper towels. 5. Minimum Waste-Receptacle Capacity: 2.6 gal.. 6. Material and Finish: Stainless steel, No:4 finish (satin). 7. Lockset: Tumbler type for towel-dispenser compartment. F. Liquid-Soap Dispenser: 1. Basis-of-Design Product: Bobrick; B Description: Designed for dispensing soap in liquid or lotion form. 3. Mounting: Vertically oriented, surface mounted. 4. Capacity: 40 oz. 5. Material and Finish: Stainless steel, No. 4 finish (satin). 6. Lockset: Tumbler type. 7. Refill Indicator: Window type. TOILET AND BATH ACCESSORIES

16 2.3 FABRICATION A. General: Fabricate units with tight seams and joints, and exposed edges rolled. Hang doors and access panels with full-length, continuous hinges. Equip units for concealed anchorage and with corrosion-resistant backing plates. PART 3 - EXECUTION A. Install accessories according to manufacturers' written instructions, using fasteners appropriate to substrate indicated and recommended by unit manufacturer. Install units level, plumb, and firmly anchored in locations and at heights indicated. B. Grab Bars: Install to withstand a downward load of at least 250 Ibf, when tested according to method in ASTM F ADJUSTING AND CLEANING A. Adjust accessories for unencumbered, smooth operation. Replace damaged or defective items. B. Remove temporary labels and protective coatings. C. Clean and polish exposed surfaces according to manufacturer's written recommendations. 3.3 SCHEDULE RESTROOM 107: 1 Mirror (18"x36") 1 Liquid Soap Dispenser (surface) 1 Grab Bars, 36" 1 Grab Bar, 42" 1 Grab Bar, 18" 1 Combination Paper Towel DispenserIWaste 1 Toilet Tissue Dispenser RESTROOM 109: 1 Mirror (18"x36") 1 Liquid Soap Dispenser (surface) 1 Grab Bars, 36" 1 Grab Bar, 42" TOILET AND BATH ACCESSORIES

17 1 Grab Bar, 18" Combination Paper Towel DispenserMaste B Toilet Tissue Dispenser B-6857 END OF SECTION TOILET AND BATH ACCESSORIES

18