Wet Areas Using Plasterboard
|
|
- Lillian Hodge
- 5 years ago
- Views:
Transcription
1 INSTALLATION 168 DEFINITIONS 168 WET AREA REQUIREMENTS 168 WATERPROOFING REQUIREMENTS BY AREA 169 GENERAL REQUIREMENTS 171 FRAMING 171 PLASTERBOARD LAYOUT 171 PLASTERBOARD FIXING 171 CONSTRUCTION DETAILS 173 Wet Areas Using Plasterboard Australian Standard AS Waterproofing of Wet Areas within Residential Buildings defines a wet area as an area within a building supplied with water from a water supply system and includes bathrooms, showers, laundries and sanitary compartments. Waterproofing of wet areas may be achieved by systems using water resistant s such as WaterShield or TruRock. This section contains: Installation instructions for wet area walls. Waterproofing treatment methods for WaterShield and TruRock walls. Construction details for wet areas. Some elements of wet area installation will be carried out by a plasterer, and other elements will be completed by trades such as plumbers and tilers. All waterproofing must be carried out by an approved applicator [Refer to 2.3 for more information on wet areas]. 167
2 3.1.4 WET AREAS USING PLASTERBOARD Installation Definitions and Wet Area Requirements Definitions WATERPROOF MEMBRANE s are a layer of material impervious to water that are usually liquid applied. They must comply with AS/NZS 4858:2004, Wet Area Membranes and be applied according to the manufacturer s instructions. FLASHING Flashing is a strip or sleeve of impervious material such as metal angle, or a liquid applied product such as a waterproof membrane. It must provide a barrier to moisture movement. SHOWER AREA Shower areas consist of enclosed and unenclosed areas: Unenclosed shower areas extend 1500mm horizontally from the shower connection on the wall, up to a height of 1800mm from the finished floor. Enclosed shower areas are bounded by walls or screens up to a height of 1800mm from the finished floor. Walls or screens include hinged or sliding doors that control the spread of water to within the enclosure A shower fitted with a frameless glass shower screen or screen over a bath less than 1500mm long is not an enclosed shower. Wet Area Requirements Different wet areas require different levels of treatment to protect them from moisture. WET AREA INSTALLATION REQUIREMENTS Area Level of Risk Walls Junctions Penetrations + Shower area High Water Resistant Waterproof Waterproof Bathrooms Medium Waterproof^ Areas adjacent to baths and spas Medium Water Resistant Waterproof Waterproof * Walls adjoining other vessels Low Water Resistant Waterproof Waterproof * Laundries and WCs Low Waterproof^ Bathrooms and laundries requiring a floor waste High Waterproof^ Waterproof + Including mechanical fixings or fasteners. ^ Applies to wall/floor junctions only. * Horizontal surface waterproof, vertical surface water resistant. to 150mm high behind tiles WaterShield or TruRock FIGURE 1 Basin 168 Technical Advice knaufmetal.com.au
3 WET AREAS USING PLASTERBOARD Waterproofing Requirements Installation Waterproofing Requirements by Area Water Resistant Walls Use WaterShield or TruRock covered with a waterproof membrane and tiles. For all joints, corners and fastener heads use MastaBase or MastaLongset. [Refer to waterproof membrane manufacturer for application instructions] Walls Adjoining Other Vessels Ensure walls within 75mm of a vessel such as a sink, basin or laundry tub are water resistant to a height of 150mm minimum above the vessel. Seal all edges where the vessel is fixed to the wall. Waterproof Penetrations Use a waterproof sealant or a proprietary flange system to waterproof penetrations. Waterproof Vertical Junctions (where required) Use a waterproof membrane as vertical flashing that has a minimum overlap of 40mm to the wall sheeting for each leg. Wall/Floor Junctions in Shower Areas and Adjacent to Baths and Spas Use a waterproof membrane on walls to: 150mm minimum above the finished shower floor level or lip of bath And 25mm minimum above the maximum retained water level And with the horizontal leg width a minimum of 50mm. Wall/Floor Junctions Outside Shower Areas Use a waterproof membrane or metal angle as flashing with a vertical leg a minimum of 25mm above the finished floor level with the horizontal leg width a minimum of 50mm. WaterShield or TruRock to 150mm high behind tiles to walls of bath as flashing 25mm min. above finished floor level Tiles FIGURE 2 Bath (without shower) installation on timber flooring Technical Advice knauf.com.au 169
4 3.1.4 WET AREAS USING PLASTERBOARD Installation Waterproofing Requirements Finishing or all-purpose compounds are only permitted outside of tiled areas WaterShield or TruRock Use only MastaBase or MastaLongset in shower area to 1800mm high Tiles as flashing with horizontal leg width of 50mm and 25mm above finished floor level 1500mm min from shower outlet. Timber floors in wet areas must be completely covered with a waterproof membrane. FIGURE 3 Internal in situ tray for unenclosed shower on concrete or compressed fibre cement floor Finishing or all-purpose compounds are only permitted outside of tiled areas Use only MastaBase or MastaLongset in shower area to 1800mm high WaterShield or TruRock Optional reinforcing angle behind as flashing 25mm min. above finished floor level External shower tray (installed before wall lining) Tiles FIGURE 4 External tray for enclosed shower on timber flooring 170 Technical Advice knaufmetal.com.au
5 WET AREAS USING PLASTERBOARD General Requirements, Framing, Plasterboard Layout and Fixing Installation General Requirements For WaterShield [Refer to non-fire rated requirements] For TruRock [Refer to fire rated requirements] Waterproof all cut edges of WaterShield or TruRock that may be affected by moisture, including all penetrations and the bottom edge over a preformed shower base. Only use paper tape and MastaBase or MastaLongset for jointing in tiled areas to strengthen the joint and provide a continuous surface for the waterproof membrane. Recess pre-formed shower bases, baths and spas sufficiently into the wall to allow the tiles to pass down the inside perimeter rebate of the shower base [Refer to Construction Details] After the installation of tiles, apply a waterproof sealant to all wall/floor junctions and vertical corner joints. Masonry adhesive and stud adhesive are not permitted in tiled areas. Frame movement should be limited at junctions in high risk areas such as showers. For this purpose use a min. 35 x 35 x 0.7mm BMT metal angle fixed to the frame in internal corners. Framing For internal steel walls [Refer to 3.1.1]. Masonry walls lined with tiles on WaterShield or TruRock must use the furring channel method. For masonry walls with [Refer to 3.1.3] Plasterboard Layout For WaterShield [Refer to non-fire rated requirements] For TruRock [Refer to fire rated requirements] Plasterboard Fixing Use the Fastener Only Method in tiled or fire rated areas. Masonry or stud adhesives are not permitted. Drive fasteners to just below the sheet surface, taking care not to break the paper linerboard. Laminating screws can be used to fix butt joints in the second and third layer. Tiles weighing up to 22 kg/m² (porcelain 9mm thick) may be installed when fasteners are spaced at imum centres. Tiles weighing from 22 to 32 kg/m² may be installed when fasteners are spaced at imum centres on studs at 450mm centres, or fasteners spaced at 100mm centres on studs at 600mm maximum centres. Technical Advice knauf.com.au 171
6 3.1.4 WET AREAS USING PLASTERBOARD Installation Plasterboard Fixing FIGURE 55 WaterShield in in Tiled Tiled Areas Areas 1 Layer 1 Layer Horizontal - Horizontal Screw Screw Only Only Method Method Butt Joints Fix at centres. Stagger by 300mm min on adjoining sheets and on opposite sides of the wall Plasterboard must not be fixed to to head track Sealant If If required, use sealant to to maintain Fix on on each stud mm Field 200mm min Recessed Edges Fix on each stud 10-50mm Sheet Edges Fix screws mm from sheet edges except at head and base tracks Corners Openings vertical screw spacing Tile Weights Tiles weighting up to 22 kg/m 2 (porcelain 9mm thick) use, screws at imum centres when studs are at 600mm centres Tiles weighing from 22 to 32 kg/m 2 use, screws at imum centres when studs are at 450mm centres, or screws at 100mm maximum centres when studs are at 600mm centres. Fix on each stud 50mm FIGURE FIGURE 66 WaterShield WaterShield in in Untiled Untiled Areas Areas 1 Layer 1 Layer Horizontal - Horizontal Screw Screw and and Adhesive Adhesive Method Method Butt Joints Stagger by 600mm min on adjoining sheets and an opposite sides of the wall Plasterboard must not be fixed to head track Sealant If required, use sealant to maintain Fix on each stud mm 300mm max 200mm min Recessed Edges Fix on each stud 10-50mm Butt Joints Float between framing for Level 4 and Level 5 finishes Temporary holding block, if required Sheet Edges Fix screws 10-50mm from sheet edges except at head and base tracks 300mm max Corners 300mm max Openings 300mm max vertical screw spacing Adhesive daubs 200mm min from screw points and edges Fix on each stud 50mm Field Adhesive daubs 25mm diameter, 15mm high and 300mm max spacing Sheet Width Fixing Pattern 900mm S A A A S 1200mm S A A A A S 1350mm S A A A A A S 172 Technical Advice knaufmetal.com.au
7 WET AREAS USING PLASTERBOARD Construction Details Details NON-FIRE RATED SHOWER NON-FIRE WALL RATED DETAILS SHOWER WALL DETAILS Bond breaker Sealant, if required to maintain Sealant, if required to maintain FIGURE 7 Shower Base Class 2 membrane shown - FIGURE 8 Shower Base Class 3 membrane shown - 2 layers of Knauf Watershield used to prevent recessing pre-formed shower base into stud work Furring channel Additional horizontal furring channel along shower base Sealant, if required to maintain FIGURE 9 Shower Base Pre-formed shower tray - 6mm gap and flexible wet FIGURE 10 Shower Base over Masonry Wall Class 3 membrane shown - Optional vertical reinforcing angle in shower area Refer to proprietry waterproof membrane manufacturer for specific application instructions. FIGURE 11 Shower Corner Plan Technical Advice knauf.com.au 173
8 3.1.4 WET AREAS USING PLASTERBOARD Details Construction Details NON-FIRE RATED BATH DETAILS BATH DETAILS Fix angle to stud at Fix 100mm angle to max stud centres at 100mm and max 50mm centres max and from ends 50mm max from ends sheet Fix 50mm bottom from Knauf WaterShield Knauf WaterShield (compatible Tiles and tile with adhesive waterproof (compatible membrane) with area Flexible sealant wet Steel stud frame to Steel support stud frame bath to support bath Notch stud 35mm max and insert Notch minimum stud 35mm 50x25, max and 1.15mm insert minimum BMT top 50x25, hat 1.15mm BMT top hat 400mm long 35x35, Bathtub 0.7mm 400mm BMT long steel 35x35, Bathtub angle 0.7mm for BMT stud steel support angle for stud support area Flexible sealant wet Waterproof membrane Waterproof membrane NON-FIRE RATED clearance to Sealant, if required to Sealant, maintain if required acoustic to maintain integrity GENERAL WET AREA DETAILS GENERAL WET AREA DETAILS FIGURE 12 Bathtub FIGURE 12 Bathtub Refer to proprietry waterproof membrane Refer to proprietry manufacturer waterproof for specific membrane application manufacturer instructions. for specific application instructions. (compatible Tiles and tile with adhesive waterproof (compatible membrane) with area Flexible sealant wet Waterproof membrane Waterproof membrane Sealant, if required to Sealant, maintain if required acoustic to maintain integrity FIGURE 13 Wall Base in General Wet Area FIGURE 13 Wall Base in General Wet Area Outside shower Class membrane shown Outside shower - Class 3 membrane shown 174 Technical Advice knaufmetal.com.au
9 WET AREAS USING PLASTERBOARD Construction Details Details FIRE RATED SHOWER WALL DETAILS SHOWER WALL DETAILS Knauf fire rated and moisture resistant Knauf fire rated and moisture resistant Knauf fire rated Knauf fire rated Bond breaker Bond breaker Knauf Bindex Fire and Acoustic Sealant required to maintain integrity Knauf Bindex Fire and Acoustic Sealant required to maintain integrity FIGURE 14 Shower Base Class 2 membrane shown - FIGURE 15 Shower Base Class 2 membrane shown - Knauf fire rated and moisture resistant Knauf Watershield Knauf fire rated and moisture resistant Knauf Watershield Knauf fire rated Knauf fire rated Support framing for bath Knauf Bindex Fire and Acoustic Sealant required to maintain integrity FIGURE 16 Shower Base Pre-formed shower tray with upstand FIGURE 17 Bathtub Knauf Bindex Fire and Acoustic Sealant required to maintain integrity Refer to proprietry waterproof membrane manufacturer for specific application instructions. For fire rated penetration details, refer to Technical Advice knauf.com.au 175
WET AREA CONSTRUCTION AUSTRALIA SEPTEMBER 2006 DESIGN MANUAL
WET AREA CONSTRUCTION AUSTRALIA SEPTEMBER 2006 DESIGN MANUAL 1 INTRODUCTION CONTENTS 1 INTRODUCTION 2 2 SUITABLE WET AREA SUBSTRATES 3 Wall and ceiling linings 3 Structural flooring sheets 3 Tile underlays
More informationExternal Steel Stud and Top Hat Walls. Details SYSTEMS 176 NON-FIRE RATED SYSTEMS 176 FIRE RATED SYSTEMS 178 BRICK VENEER SYSTEMS 183 INSTALLATION 185
Details SYSTEMS 176 NON-FIRE RATED SYSTEMS 176 FIRE RATED SYSTEMS 178 BRICK VENEER SYSTEMS 183 INSTALLATION 185 GENERAL REQUIREMENTS 185 FRAMING 185 PLASTERBOARD LAYOUT 189 PLASTERBOARD FIXING 190 EXTERIOR
More informationPLASTERBOARD WET AREA SYSTEMS MANUAL
PLASTERBOARD WET AREA SYSTEMS MANUAL USGBoral.com Plasterboard Ceilings Cornice Compounds System Solutions Plasterboard General Information GENERAL INFORMATION Contents Walls 6 Water Proofing of Wet Areas
More informationFC:101 WET AREA SYSTEMS CSR CEMINTEL RESIDENTIAL INTERIOR WET AREA LINING & FLOORING SYSTEMS
CSR CEMINTEL WET AREA SYSTEMS FC:101 RESIDENTIAL INTERIOR WET AREA LINING & FLOORING SYSTEMS AUGUST 2012 CeminSeal features waterblock technology, which provides improved water resistance and jointing
More informationSECTION D Masonry Wall Systems. Contents. Introduction. Design Considerations. Installation. Components. System Specifications.
SECTION D Wall Systems. Contents. SUBJECT Introduction Design Considerations Installation Components PAGE D2 D2 D4 D5 System Specifications Stud One Side Stud Both Sides Stud and Furring Channel Resilient
More informationGTEK TM WET AREA GTEK TM FIRE & WET AREA
APRIL 2016 TECHNICAL BROCHURE GTEK TM WET AREA GTEK TM FIRE & WET AREA gtekplasterboard.com.au WET AREA SOLUTIONS GTEK TM WET AREA WHY GTEK TM? WITH OUR ALL-AUSTRALIAN GTEK RANGE OF INTERIOR LINING PRODUCTS,
More informationCEMENT BOARD INDOOR INORGANIC CEMENT WALL AND CEILING LINING SYSTEM
CEMENT BOARD INDOOR INORGANIC CEMENT WALL AND CEILING LINING SYSTEM Contents Disclaimer Products manufactured and systems designed by Knauf are produced in accordance with the Building Code of Australia
More informationSECTION B Steel Frame Wall Systems. Contents. Steel Stud Selection Tables. Introduction. Design Considerations. Installation.
SECTION B Steel Frame Wall Systems. Contents. SUBJECT Steel Stud Selection Tables Introduction Design Considerations Installation Components PAGE B2 B4 B4 B6 B7 System Specifications Single Stud Staggered
More informationUSG BORAL WET AREA SYSTEMS. Product. Scope. Building Regulations. Appraisal No. 955 (2017) BRANZ Appraisals
USG BORAL WET AREA SYSTEMS s Technical Assessments of products for building and construction. USG Boral Building Products NZ PO Box 11-155 Ellerslie Auckland 1542 Tel: 0800 874 267 Fax: 0800 332 123 Web:
More informationInterHome SEPARATING WALL SYSTEM FOR MULTI-RESIDENTIAL CONSTRUCTION
InterHome SEPARATING WALL SYSTEM FOR MULTI-RESIDENTIAL CONSTRUCTION B Contents DISCLAIMER Products manufactured and systems designed by Knauf are produced in accordance with the Building Code of Australia
More informationBRANZ Appraisal Certificate # 461 (2010) Internal wet areas.
SPECIFICATION FOR PROTECTO WRAP AFM-WM FOR INTERNAL WET AREAS BRANZ Appraisal Certificate # 461 (2010) Internal wet areas AFM/WM INTERNAL 0104 Page 1 AFM-WM INTERNAL SPECIFICATION PRODUCT DESCRIPTION Anti
More informationGypLyner (walls) Metal framed wall lining system. GypLyner.
GypLyner GypLyner (walls) Metal framed wall lining system GypLyner is a cost-effective, virtually independent metal frame drylining system for lining walls. General purpose and suitable for all internal
More information5.0 GIB PERFORMANCE SYSTEMS INSTALLATION
5.0 GIB PERFORMANCE SYSTEMS INSTALLATION The GIB Performance Systems section covers installation of GIB EzyBrace and GIB Aqualine Wet Area Systems. For other systems including 5.1 GIB BRACING SYSTEMS This
More informationCEMINTEL FIBRE CEMENT SYSTEMs. fc101 july 2009
CEMINTEL FIBRE CEMENT SYSTEMs wet area systems residential INTERIOR wet area lining Featuring waterblock technology, providing 95% stronger joint and compound adhesion, as well as 100% paint adhesion.
More informationFIRE RATING MATERIAL FIXING NOTES
FIRE RATING MATERIAL FIXING NOTES FIRE RATING MATERIAL FIXING NOTES... 1 External Wall Systems... 2 Non load bearing steel stud walls... 3 LOAD-BEARING STEEL STUD WALLS... 3 NON LOAD-BEARING TIMBER STUD
More informationContents. Timber framing to be installed in accordance with AS:1684 Metal framing to be installed in accordance with BCA Volume: 2
Contents BCA Codes 3 General 4 Fire Performances Thermal and Acoustic Insulation Wall Installation 4 Timber Frame Separation Walls 5 Steel Frame Separation Walls 6 External Fire Rated Walls 7 Floor Installation
More informationKnauf Wall Liner. Head Track. Brackets. Wall Lining Stud. Fixings. Knauf Plasterboard. Floor Track. 98 Wall Liner
The Knauf Wall Liner System is extremely versatile and can be specified for application on masonry backgrounds with moderate irregularities between 20mm and 125mm. It can accommodate any of the range of
More informationCHAPTER 10: Finishes CONTENTS 10.1 PLASTERWORK 10.2 SECOND AND THIRD FIX FINISHES. Chapter 10
CONTENTS 10.1 PLASTERWORK 10.2 SECOND AND THIRD FIX FINISHES 283 Chapter 10 FUNCTIONAL REQUIREMENTS FUNCTIONAL REQUIREMENTS 10.1 PLASTERWORK Workmanship i. All workmanship must be within the tolerances
More informationARDEX UNDERTILE SHEET MEMBRANE (WPM 750 AND WPM 1000) Product. Scope. Building Regulations. Appraisal No. 727 [2017]
ARDEX UNDERTILE SHEET MEMBRANE (WPM 750 AND WPM 1000) This Appraisal replaces BRANZ Appraisal No. 727 (2011) BRANZ Appraisals Technical Assessments of products for building and construction. ARDEX New
More informationCHAPTER 10: Finishes CONTENTS 10.1 PLASTERWORK ND AND 3 RD FIX FINISHES
CONTENTS 10.1 PLASTERWORK 10.2 2 ND AND 3 RD FIX FINISHES FUNCTIONAL REQUIREMENT 10.1 Plasterwork Workmanship Design Technical Manual TS-011-09-010412 i. All workmanship must be within defined tolerances
More informationGypWall QUIET Acoustic separating wall system
Acoustic separating wall system 90 Al Mafraq Hospital, Abu Dhabi 0 R w db 90 0 mins is a lightweight, non-loadbearing, twin framed acoustic separating wall, primarily used as a sound resisting wall in
More informationTile Safe Shower System
Tile Safe Shower System Tile Safe Shower System CONTENTS ABOUT SHOWERWELL 2 THE SHOWERWELL TILE SAFE SHOWER SYSTEM 4 SHOWERWELL STERLING 10MM DOOR 6 SHOWERWELL 10MM SLIDING DOOR 9 SHOWERWELL STERLING
More informationWaterproofing Handbook
Waterproofing Handbook Wet-seal R Your Waterproofing Specialists Your Waterproofing Specialists Basic Hand Book for Waterproofing Builder s/client Responsibilities Safe Working Site Duty Of Care The Builder/Client
More informationPTY LTD. Paskaseal SRB. Screed Replacement Base
PTY LTD Paskaseal SRB Screed Replacement Base brochure main 3 - bluegreen.indd 1 About Us Visit us at paskaltileandstone.com.au We encourage you to come in and speak to our highly trained experts. Paskal
More informationGypLyner IWL Independent wall lining system
Independent wall lining system Photograph courtesy of Philip Brier 0 Independent wall lining system independent wall lining is a lightweight, nonloadbearing drylining which is erected independently of
More informationInstruction and Safety Manual Resilient Sound Isolation Clips (SIC Clips)
SOUND ISOLATION CLIPS Installation Manual Instruction and Safety Manual Resilient Sound Isolation Clips (SIC Clips) SOUND ISOLATION CLIP SPECIFICATIONS Width...1.00 inch Height...1.06 inch Length...3.86
More informationTiling Tiling Finishes C08
C08 Finishes In rooms subject to high or intermittent moisture conditions, the range of boards available for tiling offers flexibility of design and peace of mind when installed in both wall linings, lightweight
More informationSECTION GYPSUM BOARD
SECTION 092900 GYPSUM BOARD PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Interior gypsum wallboard. 2. Tile backing panels. B. Related Sections: 1. Section 012300 Alternates. 1.2 SUBMITTALS A.
More informationHYDRATHANE INTERIOR WATERPROOFING MEMBRANE. Product. Scope. Building Regulations. Appraisal No. 957 [2017] Appraisal No. 957 (2017) BRANZ Appraisals
HYDRATHANE INTERIOR WATERPROOFING MEMBRANE BRANZ Appraisals Technical Assessments of products for building and construction. Construction Chemicals NZ Ltd 16 Carpenter Road East Tamaki Auckland Phone (09)
More informationC08. S04. P02 P08 Tiling
! This section includes updated information, added since it was first published in December 2015. Last updated 29/03/2018 C08. S04. P02 P08 Including C08. S01. P02 Finishes introduction C08 Finishes Introduction
More informationSPAPANEL WALL LINING SYSTEM. Product. Scope. Building Regulations. Appraisal No. 906 [2016] Appraisal No. 906 (2016) Amended 11 December 2017
SPAPANEL WALL LINING SYSTEM Amended 11 December 2017 BRANZ Appraisals Technical Assessments of products for building and construction. AB Building Products Level 13, Citigroup 2 Park St Sydney NSW 2000
More informationwet area systems Product BRANZ APPRAISAL No. 427 (2007) Scope Building Regulations
Product Appraisal No.427 [2007] 1.1 GIB Aqualine Wet Area Systems are for the interior lining of timber and steel frame walls and ceilings in wet areas such as bathrooms, laundries, kitchens and toilets
More informationDesign No. HI/BP PERIMETER FIRE BARRIER SYSTEM Hilti, Inc. ASTM E 2307 Table 1
FIRESTOP JOINT SPRAY CFS-SP WB SILICONE JOINT SPRAY CFS-SP SIL F-RATING 2-HR. 2-HR. T-RATING -HR. -HR. APPLICATION THICKNESS PERIMETER FIRE BARRIER SYSTEM Hilti, Inc. ASTM E 2307 Table /8" WET FILM (/6"
More informationA. Environmental Limitations: Comply with ASTM C 840 requirements or gypsum board manufacturer's written instructions, whichever are more stringent.
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationInstallation Guide and Safety Manual Resilient Sound Isolation Clips (SIC Clips)
Installation Guide and Safety Manual Resilient Sound Isolation Clips (SIC Clips) SOUND ISOLATION CLIP SPECIFICATIONS Width...1.00 inch Height...1.06 inch Length...3.86 inch Weight....025 lbs Max Spacing...48
More informationSYSTEMS+ STEEL STUD WALLS INNOVATIVE SYSTEMS SOLUTIONS USGBORAL.COM
USGBORAL.COM S+ C 2 C 14 C 19 C 26 C 42 C 57 C 73 INTRODUCTION QUICK SELECTION TABLES LINED ONE SIDE LINED BOTH SIDES QUIET STUD STAGGERED STUD TWIN STUD C STEEL STUD WALLS INNOVATIVE S SOLUTIONS C STEEL
More informationDAVCO K10 PLUS AND K10 RAPID WET AREA MEMBRANES. Product. Scope. Building Regulations. Appraisal No. 609 [2017]
DAVCO K10 PLUS AND K10 RAPID WET AREA MEMBRANES This Appraisal replaces BRANZ Appraisal No. 609 (2008) Amended 24 May 2018. BRANZ Appraisals Technical Assessments of products for building and construction.
More informationShower Tray - Timber Floors
Shower Tray - Timber Floors Assembly information Assembly information The JACKOBOARD shower unit consists of a floor panel and a drainage system. Both components are coordinated with each other and form
More informationHYDRATHANE INTERIOR WATERPROOFING MEMBRANE. Product. Scope. Building Regulations. Appraisal No. 959 [2017] Appraisal No. 959 (2017) BRANZ Appraisals
Appraisal No. 959 [2017] HYDRATHANE INTERIOR WATERPROOFING MEMBRANE BRANZ Appraisals Technical Assessments of products for building and construction. Construction Chemicals Pty Ltd 49-57 Davis Street Wingfield
More informationMAJESTIC FLOOR MEMBRANE PRODUCT GUIDE
PRODUCT GUIDE p13 p7 p9 PRODUCT DETAIL The Majestic Floor Membrane is a self-adhesive waterproof membrane designed for use prior to the application of ceramic tiles and natural stone onto timber and solid
More informationFIRE PROTECTION. GTEC Shaftwall systems 244 GTEC Shaftwall Stairwell systems 248 GTEC Horizontal Shaftwall systems 249 GTEC Encasement systems 250
FIRE PROTECTION GTEC Shaftwall range uses a specially designed system to protect voids and shafts in buildings. It resists pressure changes and enables installation from one side of the shaft only. GTEC
More informationfermacell Powerpanel H 2 O Linear Shower Outlet 2.0
fermacell Product Data Sheet fermacell Powerpanel H 2 O Linear Shower Outlet 2.0 Product The prefabricated is the quick and economic dry solution for flush-to-floor installation of shower trays (included
More informationGypWall TM ROBUST 4.4. GypWall ROBUST. Durable impact resistant partition system. Key facts. Sector Guide
GypWall TM ROBUST GypWall ROBUST is a high impact resistant partition system for use where a more durable structure is required. The system provides a lightweight, cost-effective, non-loadbearing partition
More informationNATIONAL GYPSUM COMPANY Wood Frame Walls And Ceilings Single- And Double-Layer Construction
Walls And Ceilings Single- And Double-Layer Construction 09 9 00/NGC Single-Layer Construction The single-layer construction system consists of a single layer of Gold Bond brand Gypsum Board applied to
More informationIndependent twin frame high performance acoustic separating wall system
C04 Partitions Independent twin frame high performance acoustic separating wall system All our systems are covered by SpecSure when using genuine Gyproc and Isover products is a lightweight, non-loadbearing
More informationC05. S03. P02 P08 FireWall
! This section includes updated information, added since it was first published in December 2015. Last updated 16/12/2016 C05. S03. P02 P08 Including C05. S01. P02 Specialist partitions introduction C05
More informationAS The External Waterproofing Membranes Standard
AS 4654-2 The External Waterproofing Membranes Standard NOTE This external waterproofing standard contains solutions for problems which have not been addressed in other countries. CONFORMANCE CONDITIONS
More informationConcrete Soffit Direct Fix
Installation Guide Concrete Soffit Direct Fix Recommended Pattern insulation boards may be installed in any pattern. The recommended pattern is a square-set pattern, for simplest and quickest configuration
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 092650 - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More information06 FINISH 0621p PARCHEM waterproofing wet areas
0621P PARCHEM WATERPROOFING WET AREAS Branded worksection This branded worksection Template has been developed by NATSPEC in conjunction with PARCHEM and may be used whilst the Product Partner is licensed
More informationFIRESTOP JOINT SPRAY CFS-SP WB. 2mm (0.079") WET FILM ± 7.5 ± 5
Design No. CEJ 27 P (HI/JS 20-05) Table. CONCRETE FLOOR ASSEMBLY: Max. two-hour rated concrete floor assembly made from either lightweight or normal weight concrete with a density of 00-50 pcf, with a
More informationGypWall AUDIO The ultimate cinema wall system
The ultimate cinema wall system 9 Vox Cinemas, Muscat City Centre - Sultanate of Oman 7 0 R w db 0 0 mins is a non-loadbearing, twin frame high performance wall system that provides exceptionally high
More information0621p DUROTECH waterproofing wet areas
0621P DUROTECH WATERPROOFING WET AREAS Branded worksection This branded worksection Template has been developed by NATSPEC in conjunction with DUROTECH and may be used whilst the Product Partner is licensed
More informationC05. S03. P02 P08 FireWall
! This section includes updated information, added since it was first published in December 2015. Last updated 29/03/2018 C05. S03. P02 P08 Including C05. S01. P02 Specialist partitions introduction C05
More informationLIQUID APPLIED WATERPROOF ROOF COATINGS
J31 LIQUID APPLIED WATERPROOF ROOF COATINGS To be read with Preliminaries/General conditions. TYPE(S) OF COATING 120 WARM DECK ROOF COATING Substrate: Suitable structural roof deck (e.g. plywood, OSB3,
More informationThe extra strong, extra durable, sound resistant system that you can direct fix to
C0 Partitions The extra strong, extra durable, sound resistant system that you can direct fix to All our systems are covered by SpecSure when using genuine Gyproc and Isover products gyproc.ie Utilising
More informationWall Linings. As well as complete dry lining solutions we also provide fast-drying parge coat to ensure airtightness,
Wall Linings Our versatile range of wall lining systems makes it easy to produce a high-quality, high-performance finished wall regardless of the background. Whether your priority is acoustic control,
More informationPulaski County, Virginia
Pulaski County, Virginia Typical Carport Enclosure Details Based on the 2009 International Residential Code CONTENTS General Requirements... 2 Emergency Escape and Rescue... 2 Foundation and Floor... 3
More informationAQUABLOK INTERIOR WATERPROOFING MEMBRANES. Product. Scope. Appraisal No. 724 [2017]
WATERPROOFING MEMBRANES This Appraisal replaces BRANZ Appraisal No. 724 (2011) BRANZ Appraisals Technical Assessments of products for building and construction. Sika (NZ) Ltd PO Box 19 192 Avondale Auckland
More informationAugust 2008: Issue 1. Non - Residential New Build 4.5 Basements
Non - Residential New Build 4.5 Basements August 2008: Issue 1 Non-residential new build 4.0 Non-residential New Build Basements Contents Introduction find online page Solution optimiser and pathfinder
More informationAS Interpretation of External Waterproofing as it applies to Melbourne, Class 1 buildings
AS4654.2 Interpretation of External Waterproofing as it applies to Melbourne, Class 1 buildings Climate Zone: 6 Wind Class: N1 Membrane Types: Liquid Applied Class II and Class III as defined and tested
More informationDriLyner 5.2. DriLyner. Drywall masonry lining systems. Key facts. Sector Guide
systems provide simple and effective techniques for fixing Gyproc plasterboards or Gyproc thermal laminates to brick, block, and concrete walls. They can be used in all building types in both new-build
More informationHOW TO: CREATE METAL PARTITIONS WALL LININGS AND CEILINGS GTEC FRAMES
HOW TO: CREATE METAL PARTITIONS WALL LININGS AND CEILINGS GTEC FRAMES 1 METAL OR TIMBER? When creating stud partitions, wall linings and suspended ceilings the traditional method of installation has been
More informationProject No: Pakenham Branch Library, Pakenham, Ontario Section DECEMBER, 2016 Page 1 of 6
DECEMBER, 2016 Page 1 of 6 1 GENERAL 1.01 RELATED SECTIONS.1 Section 01 33 00 - Submittal Procedures..2 Section 07 21 16 - Batt and Blanket Insulation..3 Section 07 92 10 - Sealants..4 Section 09 91 00
More informationSuspended timber upper floors
Exposed Soffit Floors Exposed soffit Exposed soffit design Many clients perceive that rooms above exposed upper floors will be cold. However, it is possible to achieve very high levels of thermal insulation
More informationFire Door Installation
FA LCON PANEL PRODUCTS LTD 14.1 It is vital that performance doorset are installed by competent tradesmen and It is strongly recommended that the installer is a member of a recognised quality assurance
More informationDuct Wrap Flexible Wraps
Design No. 3MU/ 60-01 December 23, 2010 VENTILATION DUCT PROTECTION 3M Company 3M Fire Barrier Duct Wraps: 615 and 615+ 3M Fire Barrier Sealants: Water-Tight 1000-NS Silicone, Water-Tight 1003-SL Silicone
More informationCurved partition and wall lining system
C05 Specialist partitions Curved partition and wall lining system All our systems are covered by SpecSure when using genuine Gyproc and Isover products is a lightweight system specifically designed to
More informationCONTRACT NUMBER: W912DQ-08-C % CORRECTED DESIGN 28 JULY 2008
SECTION 092900 - GYPSUM BOARD 1.1 SUMMARY A. This Section includes the following: 1. Interior gypsum board. 2. Tile backing panels. B. Related Sections include the following: 1. Division 06 Section "Rough
More informationExterior Wall Solutions Building Shell
A strong, water tight and thermally insulated building shell will ensure the buildings sustainability of usage over time. The Exterior Shell is the most important factor of protection to ensure that the
More informationIntertenancy Barrier Systems for Terrace Homes
Intertenancy Barrier Systems for Terrace Homes Specification & Installation Manual CBI5113 NATIONAL SUPPORT VISIT: POST: Winstone Wallboards Limited 37 Felix Street, Penrose, Auckland 1061, New Zealand
More informationCONSTRUCTAFLOOR WET AREA FLOORING Residential Internal Wet Area Flooring System
DESIGN AND INSTALLATION GUIDE CONSTRUCTAFLOOR WET AREA FLOORING Residential Internal Wet Area Flooring System 2 CONSTRUCTAFLOOR Wet Area Flooring CONTENTS DESCRIPTION 2 APPLICATIONS 2 ADVANTAGES 2 COMPONENTS
More informationChevy Chase Club June 30, 2008 Bowie Gridley Architects SECTION GYPSUM BOARD SHAFT WALL ASSEMBLIES
SECTION 092116.23 - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationThe Passive Fire Protection Handbook
The Passive Fire Protection Handbook The UK s comprehensive guide to passive fire protection Chapter Ceilings, Floors and Roofs AUGUST 0 The Passive Fire Protection Handbook Contents Chapter : Introduction
More informationSECTION GYPSUM BOARD
SECTION 092900 GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationConcrete Slab-on-Ground
Concrete Slab-on-Ground This training package provides information on concrete slab-on-ground construction, including reinforcement, formwork, mix, placement and curing, for village infrastructure and
More informationGypLyner (Ceilings) Concealed grid ceiling lining system. GypLyner UNIVERSAL.
GypLyner UNIVERSAL GypLyner (Ceilings) Concealed grid ceiling lining system GypLyner ceiling is a general purpose ceiling lining system suitable for most internal applications. It is used in all types
More informationSECTION GYPSUM BOARD SYSTEM
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 09 29 00 GYPSUM BOARD SYSTEM A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification sections,
More informationSECTION GYPSUM BOARD ASSEMBLIES
PART 1 GENERAL 1.01 SECTION INCLUDES SECTION 09260 - A. Metal stud wall framing. Denoted on drawings as "metal studs". B. Metal channel ceiling framing. C. Acoustic insulation and sealant. D. Cementitious
More informationJune Non - Residential Refurbishment 5.5 Basements
June 2010 Non - Residential Refurbishment 5.5 Basements Non-residential refurbishment 5.0 Non-residential Refurbishment Basements Contents Introduction find online page Solution optimiser and pathfinder
More informationMAPEGUM WPS AND MAPELASTIC WET AREA MEMBRANES
Product 1.1 Mapegum WPS premixed and Mapelastic two-part Wet Area Membranes are liquid-applied waterproofing membranes for use under ceramic or stone tile finishes in internal wet areas. BRANZ Appraisals
More informationLIQUID APPLIED WATERPROOF ROOF COATINGS
J31 LIQUID APPLIED WATERPROOF ROOF COATINGS To be read with Preliminaries/General conditions. TYPE(S) OF COATING 120 WARM DECK ROOF COATING Substrate: Suitable structural roof deck (e.g. Plywood, OSB3,
More informationImpresa. The Standard in Custom Showers. impresa. tile showers
Impresa. The Standard in Custom Showers impresa tile showers Contents: 01. Impresa Defined 02. Impresa Sets the Standard 03. METRO 11. Stile 19. Stile Stainless 23. QuikNICHE Recessed Shampoo Shelf 25.
More informationSchluter -KERDI-BOARD Substrate, building panel, bonded waterproofing
Schluter -KERDI-BOARD Substrate, building panel, bonded waterproofing Schluter -KERDI-BOARD The universal substrate for tiles Flat. Level. Plumb. Square. No matter the quality, cost, or extravagance of
More informationChevy Chase Club June 30, 2008 Bowie Gridley Architects
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationJune Residential Refurbishment Basements
June 2010 Residential Refurbishment 3.5.1 Basements Residential refurbishment 3.0 Residential Refurbishment Basements Contents Introduction find online page Solution optimiser and pathfinder 293 Design
More informationexangle installation guide EXANGLE Finishing Sections
exangle installation guide EXANGLE Finishing Sections rondo exangle FINISHING SECTIONS GENERAL INFORMATION The Rondo EXANGLE and EXANGLE Render & Texture range has been developed over 45 years by Rondo
More informationGypWall RAPID db Plus
Metal stud housing partition system! This section includes updated information, added since it was first published in July 009. Please see the WHITE BOOK update document for details. Last updated 0/0/00
More informationSIKALASTIC-152 EXTERIOR WATERPROOFING MEMBRANE. Product. Scope. Appraisal No. 811 [2013] Appraisal No. 811 (2013) Amended 28 August 2017
SIKALASTIC-152 EXTERIOR WATERPROOFING MEMBRANE Amended 28 August 2017 BRANZ Appraisals Technical Assessments of products for building and construction. Sika (NZ) Ltd PO Box 19 192 Avondale Auckland 1746
More informationSingle frame acoustic separating wall system
GypWall QUIET SF GypWall QUIET SF Single frame acoustic separating wall system GypWall QUIET SF metal stud partition is a lightweight, non-loadbearing, single frame wall system. Subject to Local Authority
More informationMULTICOM WALL PANEL SYSTEM. Product. Scope. Building Regulations. Appraisal No. 869 [2014] Appraisal No. 869 (2014) Amended 06 March 2015
MULTICOM WALL PANEL Amended 06 March 2015 BRANZ Appraisals Technical Assessments of products for building and construction. Resco Limited 12 Kahu Crescent Te Rapa Hamilton Tel: 0800 800 950 Fax: 07 850
More informationSECTION GYPSUM BOARD
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 29 00 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationProduct. BRANZ APPRAISAL No. 474 (2010) Scope. Flexco (NZ) Ltd P O Box South Auckland Mail Centre Manukau City
Product 1.1 Flexi-Seal Interior Waterproofing Systems are of two types, one a two-part cementitious, acrylic modified, the other (Flexi-Seal PUD) a single part water based polyurethane modified. Both are
More informationSECTION GYPSUM BOARD SYSTEM
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 09 29 00 GYPSUM BOARD SYSTEM A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification sections,
More informationSpecifications for Insulation Board wall and ceiling applications
Specifications for Insulation Board wall and ceiling applications Product Ref: Marmox Multiboard 600mm wide, 1250/2500mm long. 10, 12.5, 20, 30, 40, 50, 60mm thick. Also known as Marmox Board- Pro and
More informationWPM WATERPROOFING MEMBRANE
WPM 300 - WATERPROOFING MEMBRANE Description WPM 300 Waterproofing Membrane is a single-pack, water based polyurethane modified synthetic rubber polymer, liquid membrane developed specifically as a tough,
More informationStaggered stud acoustic partition system
C0 Partitions Staggered stud acoustic partition system All our systems are covered by SpecSure when using genuine Gyproc and Isover products is a non-loadbearing stud partition incorporating a single framework
More information84 Lapping & Jointing 86 Service Pipe Penetrations 87 Sealing to Cavity Wall Constructions 88 Protecting Membranes System Components.
84 Lapping & Jointing 86 Service Pipe Penetrations 87 Sealing to Cavity Wall Constructions 88 Protecting Membranes 90 System Components installation/ SYSTEM COMPONENTS INSTALLATION ADVICE LAPPING and JOINTING
More information