SOUTHEASTERN PENNSYLVANIA TRANSPORTATION AUTHORITY 1234 MARKET STREET, PHILADELPHIA, PA SPECIFICATION FOR CERAMIC TILE FOR 15 th STREET STATION

Transcription

1 SOUTHEASTERN PENNSYLVANIA TRANSPORTATION AUTHORITY 1234 MARKET STREET, PHILADELPHIA, PA SPECIFICATION FOR CERAMIC TILE FOR 15 th STREET STATION TABLE OF CONTENTS Specification Sections: Division 1: General Requirements o Section Submittals and Contractor Responsibilities Division 9: Finishes o Section Tile Drawing Schedule: Sheet Title A-114 Platform Level Enlarged Plan 1 A-115 Platform Level Enlarged Plan 2 A-116 Platform Level Enlarged Plan 3 A-117 Platform Level Enlarged Plan 4 A-134 Platform Level Finishes Plan 1 A-135 Platform Level Finishes Plan 2 A-136 Platform Level Finishes Plan 3 A-137 Platform Level Finishes Plan 4 A-213 Elevations 16 th St North Mezzanine A-215 Elevations 16 th St South Mezzanine A-216 Elevations 16 th St South Mezzanine A-221 Elevations Westbound Platform Level A-222 Elevations Westbound Platform Level A-223 Elevations Eastbound Platform Level A-224 Elevations Eastbound Platform Level A-409 Stair W2 Large Scale Views A-410 Stair E2 Large Scale Views A-411 Stair W3 Large Scale Views A-412 Stair E3 Large Scale Views A-413 Stair E1 Large Scale Views A-502 Finishes Platform Level Details A-504 Finishes Typical Details A-506 Finishes Trim Miscellaneous Details A-507 Finishes Trim Miscellaneous Details A-601 Partition Types and Details A-604 Finish Schedule CSK-01 Platform Tile Detail STEP ASIDE ORIGINATOR: Brian Fey, RA Project Architect Bridges and Buildings Department DATE: August 2016 PROJECT: 15 th Street Station

2 City Hall Station Renovations: 15 th Street Phase August 2016 Ceramic Tile PART 1 GENERAL 1.01 Description SECTION SUBMITTALS AND CONTRACTOR RESPONSIBILITIES A. The work of this specification consists of the fabrication and delivery of ceramic tile and all associated materials including tile setting materials, grout, sealants, metal edge strips and other products as specified herein. B. SEPTA shall be responsible for final installation Submittals A. General 1. The Contractor shall provide to SEPTA the required submittals within the timeframe specified in the purchase order and after the Contractor's receipt of Notice to Proceed. 2. The Submittals shall be reviewed by SEPTA's Project Manager. The results of each submittal review shall have the following status stamp: -NO EXCEPTIONS TAKEN -PROCEED AS NOTED; REVISE AND RESUBMIT FOR RECORD -DO NOT PROCEED; REVISE AND RESUBMIT -REJECTED -NOT APPLICABLE 3. Review and Processing shall not relieve the Contractor from responsibility for errors which may exist in the submitted data. 4. Submittals not in compliance with the Contract will be returned to the Vendor for revision. Any loss of time and additional costs associated with re-submittal(s) shall be the Contractor 's responsibility. 5. Submittals that are marked "Proceed as Noted" are for the purpose of expediting procurement and/or fabrication of the intended work. The Contractor shall incorporate all corrections and resubmit to SEPTA within 10 working days the required copies of all submittals marked "Proceed as Noted." 6. The Contractor shall allow 10 working days for review and processing by SEPTA following its receipt of the submittals Substitutions A. Or Equal Substitutions 1. Restricted Items: Where items of equipment and/or materials are specifically identified in the Specifications or on the Drawings by a manufacturer's name, model or catalogue number, only such specific items may be used. When several materials are specified by name for one use, the Contractor may select any of those specified. Materials specified by manufacturer s trade name shall comply with the manufacturer s printed Specifications and data. 2. Equals Considered: Whenever a material or article required is specified or shown on the plans by using the name of the proprietary product or of a particular manufacturer or vendor, any material or article which will, in the opinion of SEPTA's Project Manager, perform adequately the duties imposed by general design will be considered equal and satisfactory provided material or article so proposed is of equal aesthetic, substance and function in SEPTA's Project Manager's opinion. It shall not be purchased or installed without SEPTA's Project Manager's written approval. "Or Equal" requests will be considered only when substantiated by the Contractor's submittal of data documenting the "or equal" nature of material or article within ten (10) calendar days after the date of receipt of Notice to Proceed. PART 2 PRODUCTS Section Submittals and Contractor Responsibilities Page 1 of 2

3 City Hall Station Renovations: 15 th Street Phase August 2016 Ceramic Tile 2.01 Not Used PART 3 EXECUTION 3.01 Material and Quantities A. Vendor is required to perform material takeoffs and provide enough material for a complete installation. B. Extra Materials: Provide 5 percent of each type of tile for future repair Packing and Shipping A. All items shall be shipped at one time as complete packages, with all components and installation hardware included. B. All components shall be packaged and shipped so as to protect the integrity and finish from any damage whatsoever. C. The Contractor shall contact SEPTA at least 48 hours prior to delivery Installation A. Installation shall be by SEPTA work forces. END OF SECTION Section Submittals and Contractor Responsibilities Page 2 of 2

4 SECTION TILE PART 1 - GENERAL 1.1 Description A. The work of this section includes the supply and delivery of all ceramic tile and installation materials specific herein and as shown on the drawings including but not limited to the following: 1. Ceramic tile. 2. Waterproof membrane. 3. Crack isolation membrane. 4. Metal edge strips. B. Installation by SEPTA. 1.2 Related Work A. Related Documents: Drawings and general provisions of the Contract, and Division 1 Specification Sections, apply to this Section. B. Related Sections: 1. Section Selective Non-Structural Demolition. 2. Section Masonry Units. 3. Section Joint Sealants. 4. Section Stainless-Steel Doors and Frames. 5. Section Sliding Security Grilles. 6. Section Non-Load-Bearing Steel Framing, for partitions. 7. Section Gypsum Board. 1.3 Submittals A. Action submittals 1. Product Data: For each type of product indicated. 2. Samples: a. Each type and composition of tile and for each color and finish required. b. Assembled samples, with grouted joints, for each type and composition of tile and for each color and finish required. c. Stone thresholds in 6-inch lengths. d. Submit tile, sealant and grout color samples at the same time. B. Sustainable Design submittals: 1. Product Data for adhesives, grouts and sealants, documentation including printed statement of VOC content. 2. Product Data for tile floors, documentation from an independent testing agency indicating compliance with the FloorScore Standard. 1.4 Quality Assurance A. Freeze/Thaw: Tiles shall be suitable for exterior use in freeze/thaw applications, with less than 3% water absorption per ASTM C1026. Tile

5 B. Mockups: Build mockups to verify selections made under sample submittals and to demonstrate aesthetic effects and set quality standards for materials and execution. 1. Build mockup of each type of floor tile installation. 2. Build mockup of each type of wall tile installation. 3. Approved mockups may become part of the completed Work if undisturbed at time of Substantial Completion. 1.5 Maintenance Material Submittals A. Furnish extra materials that match and are from same production runs as products installed and that are packaged with protective covering and identified with labels describing contents. PART 2 - PRODUCTS 2.1 Tile Products A. Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the work include the following, or approved equal: 1. Basis of design: Crossville, colors and patterns as scheduled. B. ANSI Ceramic Tile Standard: Provide standard grade tile that complies with ANSI A137.1 for types, compositions, and other characteristics indicated. C. FloorScore Compliance: Tile for floors shall comply with requirements of FloorScore Standard. D. Low-Emitting Materials: Tile flooring systems shall comply with the testing and product requirements of the California Department of Health Services' "Standard Practice for the Testing of Volatile Organic Emissions from Various Sources Using Small-Scale Environmental Chambers." E. Tile Type [CT-1]: Unglazed paver tile (floor field) 2. Face Size: Nominal 12 by Face: Plain with square edges. 5. Finish: Mat, opaque. 6. Tile Color and Pattern: Cross Colors LP series, color LA63 Red Rock; V1 shade variation (basis of design). 8. Trim Units: Coordinated with sizes and coursing of adjoining flat tile where applicable. F. Tile Type [CT-2]: Unglazed paver tile (border) 2. Face Size: Nominal 12 by 12 and 8" x 12" and 12" x 24 Inches for wall applications. Cut tiles as required to fit slopes directly above cove based and at stairs and ramps. 4. Face: Plain with square edges. 5. Finish: Mat, opaque. Tile

6 6. Tile Color and Pattern: Retro Active series, color B110 Antico Taupe. 8. Trim Units: Coordinated with sizes and coursing of adjoining flat tile where applicable. Provide shapes as follows, selected from manufacturer's standard shapes: a. Base Cove: Cove, module size 2 by 12 [CT-4]. G. Tile Type [CT-3]: NOT USED H. Tile Type [CT-4]: NOT USED I. Tile Type [CT-5]: glazed wall tile (field) 2. Face Size: Nominal 3x12 4. Face: Plain with eased edges. 5. Finish: Glossy, opaque. 6. Tile Color and Pattern: Retro Active series, color A215 Empress White J. Tile Type [CT-6]: glazed wall tile (custom accent) 2. Face Size: Nominal 4x12 4. Face: Plain with eased edges. 5. Finish: Glossy, opaque. 6. Tile Color and Pattern: Custom color (allow up to 3) a. Pantone color: PMS 370 (Trolley line) b. Pantone color: PMS 285 (MF line) K. Tile Type [CT-7]: Embossed metallic wall tile (accent). 1. Composition: Solid stainless steel 2. Face Size: Nominal 1 by Finish: Smooth with embossed pattern. 5. Color and Pattern: Metals, Stainless Steel series, color MT280 Squares. 6. Grout Color: As selected by Architect from manufacturer's full range. L. Tile Type [CT-8]: glazed wall tile (accent) 2. Face Size: Nominal 6x6 4. Face: Plain with bullnose edge. 5. Finish: Matte, opaque. 6. Tile Color and Pattern: Retro Active series, color B110 Antico Taupe. M. Tile Type [CT-9]: NOT USED N. Tile Type [CT-10]: glazed wall tile 2. Face Size: Nominal 12x12 Tile

7 4. Face: Plain with eased edges. 5. Finish: Gloss 6. Tile Color and Pattern: Retro Active series, color A215 Empress White O. Tile Type [CT-11]: outside cove base corner 2. Face Size: Nominal 2x4 4. Face: outside cove base corner 5. Finish: Matte 6. Tile Color and Pattern: Retro Active series, color B110 Antico Taupe. 2.2 Crack Isolation and Waterproof Membrane A. General: Manufacturer's standard product that complies with ANSI A and is recommended by the manufacturer for the application indicated. B. Product: Bostik Hydroment Gold TM (basis of design) or approved equal. 2.3 Setting Materials A. Water-Cleanable, Tile-Setting Epoxy: ANSI A118.3, with a VOC content of 65 g/l or less when calculated according to 40 CFR 59, Subpart D (EPA Method 24). 1. Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following: a. Bostik Stone Wall TM (basis of design) b. Laticrete International, Inc. c. MAPEI Corporation Grout Materials A. Water-Cleanable Epoxy Grout: ANSI A118.3, with a VOC content of 65 g/l or less when calculated according to 40 CFR 59, Subpart D. 1. Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following: a. Bostik True Color TM (basis of design) b. Laticrete International, Inc. c. MAPEI Corporation. 2. Grout to provide antimicrobial protection which inhibits the growth of bacteria, mold, or mildew on the surface of dried grout and enables it to resist stains caused by mold. 3. Color: to be UV stable. 4. Vertical surfaces: provide non-sag performance 2.5 Elastomeric Sealants A. General: Provide sealants, primers, backer rods, and other sealant accessories that comply with the following requirements and with the applicable requirements in Division 07 Section "Joint Sealants." Tile

8 1. Sealants shall have a VOC content of 250 g/l or less when calculated according to 40 CFR 59, Subpart D (EPA Method 24). B. One-Part, Mildew-Resistant Silicone Sealant: ASTM C 920; Type S; Grade NS; Class 25; Uses NT, G, A, and, as applicable to nonporous joint substrates indicated, O; formulated with fungicide, intended for sealing interior ceramic tile joints and other nonporous substrates that are subject to in-service exposures of high humidity and extreme temperatures. C. Multipart, Pourable Urethane Sealant for Use T: ASTM C 920; Type M; Grade P; Class 25; Uses T, M, A, and, as applicable to joint substrates indicated, O. 2.6 MISCELLANEOUS MATERIALS A. Trowelable Underlayments and Patching Compounds: Latex-modified, portland cementbased formulation provided or approved by manufacturer of tile-setting materials for installations indicated. B. Metal Edge Strips: Angle or L-shape, stainless steel, ASTM A 666, 300 Series exposededge material. C. Grout Sealer: Manufacturer's standard silicone product for sealing grout joints and that does not change color or appearance of grout. PART 3 - EXECUTION 3.1 General A. Installation of tile and accessories will be by SEPTA. 3.2 Examination A. Examine substrates, areas, and conditions where tile will be installed, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of installed tile. Verify that substrates for setting tile are firm, dry, clean, free of coatings that are incompatible with tile-setting materials including curing compounds and other substances that contain soap, wax, oil, or silicone; and comply with flatness tolerances required by ANSI A for installations indicated. 3.3 Preparation A. Remove loose or chipped terrazzo. B. Fill cracks, holes, and depressions in concrete substrates for tile floors installed with adhesives or thin-set mortar with trowelable leveling and patching compound specifically recommended by tile-setting material manufacturer. C. Blending: For tile exhibiting color variations, use factory blended tile or blend tiles at Project site before installing. D. Field-Applied Temporary Protective Coating: If indicated under tile type or needed to prevent grout from staining or adhering to exposed tile surfaces, pre-coat them with continuous film of temporary protective coating, taking care not to coat unexposed tile surfaces. Tile

9 3.4 Installation A. Comply with Tile Council of America's "Handbook for Ceramic Tile Installation" for TCA installation methods applicable to the types of installations specified and shown on drawings. Comply with parts of the ANSI A108 Series "Specifications for Installation of Ceramic Tile" that are referenced in TCA installation methods, and apply to types of setting and grouting materials used. B. Extend tile work into recesses and under or behind equipment and fixtures to form complete covering without interruptions unless otherwise indicated. Terminate work neatly at obstructions, edges, and corners without disrupting pattern or joint alignments. C. Accurately form intersections and returns. Perform cutting and drilling of tile without marring visible surfaces. Carefully grind cut edges of tile abutting trim, finish, or built-in items for straight aligned joints. Fit tile closely to electrical outlets, piping, fixtures, and other penetrations so plates, collars, or covers overlap tile. D. Provide manufacturer's standard trim shapes where necessary to eliminate exposed tile edges. E. Jointing Pattern: Lay tile in grid pattern unless otherwise indicated. Lay out tile work and center tile fields in both directions in each space or on each wall area. Lay out tile work to minimize the use of pieces that are less than half of a tile. Provide uniform joint widths unless otherwise indicated. Lay out tile work so that joints are continuous between floor, base and wall tile, as shown. F. Expansion Joints: Provide expansion joints and other sealant-filled joints, including control, contraction, and isolation joints, where indicated. Form joints during installation of setting materials, mortar beds, and tile. Do not saw-cut joints after installing tiles. 1. Where joints occur in concrete substrates, locate joints in tile surfaces directly above them. 2. Prepare joints and apply sealants to comply with requirements in Division 07 Section "Joint Sealants." G. Salvaged Wall Tile: 1. If required by job conditions during installation of new work or demolition of existing finished walls, and approved by the SEPTA Project Manager, carefully remove, clean and salvage tiles attached to substrate affected by the Work. 2. Protect, package and store any salvaged tile in location on site as directed by the SEPTA Project Manager. END OF SECTION Tile

10 NOTE: S T E P A S I D E 1. DETAIL OCCURS AT EIGHTEEN (18) LOCATIONS ON BOTH THE EASTBOUND AND THE WESTBOUND PLATFORMS. COORDINATE LOCATIONS IN THE FIELD WITH MFL OPERATIONS. 2. CUT TILES AS REQUIRED TO COORDINATE WITH CONTROL JOINTS IN PLATFORM. 24" X 48" PLASTIC TACTILE PAVER PLASTIC RUBBING EDGE CENTERLINE OF TRAIN DOOR 15th STREET STATION MARKET FRANKFORD LINE CITY HALL STATION RENOVAITONS ARCHITECTURE "STEP ASIDE" TILE DETAIL 8-INCH TALL LETTERS CUT FROM TILE CT-12 12x12 BORDER TILE, CT-2 12x12 FIELD TILE, CT-1 SCALE: DATE: WORK ORDER NO.: SHEET NUMBER DWG. NO.: SCALE FACTOR: 3/4"=1'-0" 1:1 9/1/16 CCS-CH DRAWN BY: CHECKED BY: CSK-01 1 OF 1 BJF JM STATUS DATE PRINTED: 9/8/2016 3:31:41 PM S:\BRIDGESANDBUILDINGS_FACILITIESENGINEERING\PROJECTS\2015\15AH\ARCH\MATERIALS\PORCELAIN TILE\DRAWINGS\MFL 15TH TILE DET.DWG