SIKA EGYPT ENG. HOSSAM ABD ELMAGIED SPECIFICATION DEPARTMENT DEC. 2016

Transcription

1 SIKA EGYPT ENG. HOSSAM ABD ELMAGIED SPECIFICATION DEPARTMENT DEC. 2016

2 TARGET MARKETS Concrete Waterproofing Roofing Flooring Sealing & Bonding Refurbishment Industry 2 December 27, 2016

3 3 WATERPROOFING

4 PROJECT DESCRIPTION: Secon Towers project - located in El Maadi Kournish El Nile Cairo Egypt. The project consists of 3 multi-storey underground car park with an area that exceeds m2 near Nile River that makes the ground water table less than 4.50 m. Sika Solution: Sika proposed Sika compartment system that includes : - Sika Plan WP HL as a PVC layer 2mm thick. as a flexible High tensile& elongation Waterproofing membrane sheets. - Sika Waterstop AR-31, AR-25 AND AR 20 High quality PVC Waterstop for long durability. 4 December 27, 2016Specification training 2016 / MLg

5 SECON TOWERS 5 December 27, 2016Specification training 2016 / MLg

6 6 December 27, 2016Specification training 2016 / MLg

7 NEW WATERPROOFING PRODUCTS : TOP SEAL 107 ELASTIC High elastic waterproofing Cement based Slurry. Capable of accommodating substrate flexural strains. Crack bridging capability. In thermal movements and vibrations. Optimum adhesion onto almost all substrates Uses : in different structures including those subjected to thermal movement and vibrations Hydraulic structure, terraces, Balcones and Precast concrete

8 ROOFING

9 MARASSI BEACH CLUB 9 December 27, 2016Specification training 2016 / MLg

10 Project Description - The Club house located in Marassi Project in North coast where there Is a heavy rain the winter cause a lot of Leakage on the roof - There is two different roofs in using, One is accessible which Sika suggested the Combo roof system in and the second is non-accessible which Sika suggested the Sika Lastic 560 system reinforced with Sika Lastic Fleece Requirements: - A durable System for roofing the Club house accessible roof - New innovation system for the non-accessible roofs - Easy maintain system which can be maintained easily - For the non-accessible areas they need a roofing system which can be used without removing the old tiles and Insulation - Fast application system 10 December 27, 2016Specification training 2016 / MLg

11 COMBO ROOF SYSTEM 11 December 27, 2016Specification training 2016 / MLg

12 SIKA INTEGRATED ROOFING SYSTEM ( COMBO ROOF) 1- Sika Topseal 107 Elastic 1 2- Screed in panels and Slopes 3- Separation Layer 4- Sika Raintite Acrylic Paint 5- SIKA PU foam Spray 6- Roof Slab WHY CHOOSE??? 1- Cost effectiveness: application, repair and maintenance is a seamless and easy process allowing long term investment. VID GP 2- Double layered waterproofing system: due to its double layer of monolithic system and its closed cell construction in the foam forms an impermeable waterproofing layer. 3- Saving Energy: it is based on the latest PU technology keeping the heat out reducing the use of air conditions which in turn saves up to 40% in electricity bills 12

13 SIKA INTEGRATED ROOFING SYSTEM TECHNICAL EVALUATION AGAINST THE CONVENTIONAL SYSTEM SIKA INTEGRATED ROOFING SYSTEM Integrated Roofing System is offering comprehensive system by a single manufacturer BITUMEN MEMBRANE SYSTEM Non-availability of any comprehensive roofing system by single manufacturer - spray polyurethane foam with average density Kg/m3 & thickness 4(±1) cm. Sika PU foam Spray - apply an acrylic UV protection waterproof coating sika Raintite - - lay a geotextile filter fabric over the roof area as a protection layer prior to the start of screeding works. - lay protective screed with average thickness 5cm making all required paneling work to attain the desired slope levels as well as sealant filling to all expansion joints (Sikaflex 1a). Apply Elastomeric cementitious coating sika topseal 107 elastic Heat Insulation and waterproofing joints free Provides a monolithic continuous surface with no edges, seams, gaps or joints. Offers best K-value 0.02w/mk means 3cm PU foam is equivalent to 5cm extruded polystyrene. - Install torch applied water proofing membrane making all required flashing. - lay polyethylene 1000g protective sheet on the membrane. - Install extruded polystyrene heat insulation boards with 7cm thickness. - Supply & lay a geotextile filter fabric over the roof area as a protection layer prior to the start of screeding works. - Supply & lay protective screed with average thickness 5cm making all required paneling work to attain the desired slope levels as well as sealant filling to all expansion joints (by others). 6- Elastomeric cementitious coating. Heat Insulation and waterproofing with joints Required to be cut & welded taking into consideration overhangs, overlaps, seams & joints. K-value w/mk means 5cm extruded polystyrene is equivalent to 3cm PU foam.

14 SIKA INTEGRATED ROOFING SYSTEM TECHNICAL EVALUATION AGAINST THE CONVENTIONAL SYSTEM SIKA INTEGRATED ROOFING SYSTEM Self adhering without fasteners preventing water migration laterally under insulation if any damage occur. Self flashing Higher density Kg/m3 means higher mechanical properties like compressive strength. Self adhering without fasteners resisting wind uplift problems. Excellent application for irregular surfaces such as corrugated, critical, inaccessible or curved areas. Rapid installation times BITUMEN MEMBRANE SYSTEM water migrates laterally under insulation if any damage occur making it very difficult to find or repair a leak. Mechanically Attached flashing Lower density Kg/m3 means lower mechanical Properties. Mechanically Secured to roof with fasteners & can lift off under high wind. Only can be used on flat areas. Much more time needed especially in hard to treat areas. 14 December 27, 2016 Title of Presentation / Meeting Name

15 LIQUID APPLIED MEMBRANE ( SIKA LASTIC 560 ) 15 December 27, 2016Specification training 2016 / MLg

16 16 FLOORING

17 ARAB AMERICAN VEHICLES FACTORY AAV CAIRO SUEZ DESERT ROAD 17 December 27, 2016Specification training 2016 / MLg

18 Project description : - Arab American Vehicles Company (120,000 square meter) facility located on the out skirts of Cairo with a production capacity of 17,600 vehicles annually. Project requirements : 1. Petrol and oil resistant floor 2. Minimum maintenance 3. Cost effective solution 4. Fast completion in the shortest possible time 18 December 27, 2016Specification training 2016 / MLg

19 Photos from site 19 December 27, 2016Specification training 2016 / MLg

20 20 December 27, 2016Specification training 2016 / MLg

21 SYSTEM SPECS : - Primer : Sika Floor Epoxy Mortar ( 4 mm ) : Sika Floor 161 ( A+B+C ) - Self leveling ( 2-3 mm ) Sika Floor 263SL 21 December 27, 2016Specification training 2016 / MLg

22 JOINT SEALING Sikaflex supported by a Sika Rod joint base. Sikaflex SikaRod 22 D b S ifi ti t i i 2016 /ML

23 REFURBISHMENT

24 RAGAB SCHOOL COMPLEX 24 December 27, 2016Specification training 2016 / MLg

25 RAGAB SCHOOL COMPLEX one of the newest educational projects in Alexandria, with a special design and theme. 3 Schools inside one big complex ( m2 ) PROJECT REQUIREMENTS - Indoor and Outdoor Tile Adhesive for fixing tiles and Facades all over the school, Tiles are by Restic Tiles a new technology. PROJECT PARTICIPANTS: Consultant: EL Oraibi Architects Contractor : MASS, Abu Shabana Conc, EL Bishbichi Conc 25 December 27, 2016Specification training 2016 / MLg

26 Photos from site 26 December 27, 2016Specification training 2016 / MLg

27 TILE ADHESIVE: SIKA CERAM 205 LARGE (C2TE classified according to EN 12004) - SikaCeram -205 Large is one-pack, premixed adhesive consisting of high resistance cements, high polymers content, selected silicon/quartz mineral charges and specific additives. Suitable for laying in over-tiling, swimming pools, façade or heavy traffic environments. 27

28 3. TILE ADHESIVES 3.1 SPECIFIED CODE OR STANDARD EN ( European Norm) EN For Tile Adhesives EN For Grouting Material ANSI ( American National Standard Institute) ANSI For Tile Adhesives and Grouting 28 December 27, 2016 Title of Presentation / Meeting Name

29 3. TILE ADHESIVES 3.1 NORMS Definition of types based on binder s chemical nature. C Cement-based binder D Dispersion of resins R Reactive binder Classes related to final performances as adhesion strength: 1 Normal 2 Improved (meets requirements for additional characteristics) Classes related to products workability features: F Fast (only for class C) T Thixotropic E Extended Open Time (only for class C and D) Classes related to Transversal deformation level (Only for type C) S1 deformable S2 highly deformable 29 December 27, 2016 General Overview

30 HOW TO KEEP IN TOUCH

31 WE ARE HERE FOR YOU - Sika Product finder application - Sika Egypt site - Sika Egypt Pages in social media : Facebook & Linked In & Twitter Or contact us directly : Specification team Sales team Technical support team 31 December 27, 2016Specification training 2016 / MLg

32 THANK YOU FOR YOUR ATTENTION