SECTION PAINTED PAVEMENT MARKINGS. A. Section Includes: Painted traffic striping and symbols on pavements and curbs.
|
|
- Juniper Cunningham
- 6 years ago
- Views:
Transcription
1 SECTION PAINTED PAVEMENT MARKINGS PART 1 - GENERA 1.1 SUMMARY A. Section Includes: Painted traffic striping and symbols on pavements and curbs. B. Related Documents: The Conditions of the Contract and Division 1 apply to this section as fully as if repeated herein. 1.2 REFERENCES A. The editions of the specifications and standards referenced herein, published by the following organizations, apply to the bituminous concrete paving work only to the extent specified by the reference. Refer to Section for information concerning availability and use of references. Standard Specifications: State of California, Department of Transportation (CALTRANS) Standard Specifications, May 2006, referred to herein as "Standard Specifications". 1.3 SUBMITTALS A. Product Data: Submit certificates of compliance, manufacturer's specifications, and general recommendations for paint and reflective glass beads. B. Shop Drawings: For pavement markings. 1. Indicate pavement markings, colors, lane separations, defined parking spaces, and dimensions to adjacent work. 2. Indicate, with international symbol of accessibility, spaces allocated for people with disabilities. 3. Indicate stencil lettering font, height, text, and locations. C. Submittal procedures and quantities are specified in Section REGULATORY REQUIREMENTS A. Provide pavement markings meeting the accessibility requirements of the 2013 California Building Code (CBC) Title 24 Part 2 Chapter 11B Accessibility; and 2010 ADA Standards for Accessible Design. 1.5 DELIVERY, STORAGE, AND HANDLING A. Deliver paints and paint materials in original sealed containers that plainly show the designated name, batch number, color, and date of manufacture, manufacturer's directions, Painted Pavement Markings
2 and name of manufacturer. Provide storage facilities at the project site for maintaining materials at temperatures recommended by the manufacturer. 1.6 ENVIRONMENTAL CONDITIONS A. Do not apply paint when either air or pavement temperature is below 50 degrees F or above 95 degrees F; or when rain, fog, condensation, or temperatures below 50 degrees F are anticipated during the drying period. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Manufacturers: 1. Plexipave, Division of California Products; 2. Ennis-Flint; Waterborne Traffic Paint. 3. Substitutions: Section Product Substitution Procedures. B. Basis of Design Product: Plexipave; Hi-Hide Plexicolor Line Paint. 1. Colors: As indicated on drawings. 2.2 PAVEMENT MARKNG PAINT A. The Line Paint, as designated on drawings and in specifications, for use over asphaltic and tar emulsion surfaces including slurry coats, shall conform to the following characteristics and performance: 1. The paint shall be a 100% acrylic emulsion type containing no alkyds, butadiene styrene, or vinyls and shall be thinned with water only. The paint shall also be suitable for application by brush, spray, or roller. 2. All materials used in the manufacturing of paint shall be of good commercial quality entirely suitable for the purpose intended under normal conditions for use. For white color, the opaque portion of the pigment shall be rutile titanium dioxide and the vehicle shall consist of 100% acrylic polymer dispersed in water together with the minimum amounts of necessary additives; such as pigment dispersents, anti-foaming agents, and preservatives; but no driers shall be used. 3. The white paint shall meet a minimum requirement of total solids (percent by weight or paint) of 51.5% and a maximum pigment content (percent by weight of paint) of 36%. The white paint shall contain not less than three pounds per gallon of treated rutile titanium dioxide. A minimum fitness of grind of 4 and a viscosity (Krebs Units) of 80 minimum and 95 maximum is required. The paint shall brush easily and have good flowing, leveling, and spreading characteristics and shall be suitable for application by spray equipment or rollers Painted Pavement Markings
3 4. This paint shall be suitable for use over all types of bituminous surfaces and, when applied over emulsified asphalt, it shall not cause lifting, crazing, peeling, or other damage to the base. PART 3 - EXECUTION 3.1 EXAMINATION A. Verify that pavement is dry and in suitable condition to begin pavement marking according to manufacturer s written instructions. B. Proceed with pavement marking only after unsatisfactory conditions have been corrected. 3.2 PREPARATION A. Do not apply pavement-marking paint until layout, colors, and placement have been verified with the Architect. B. Immediately before applying the paint, thoroughly clean the pavement surface of dust, dirt, sand, scale, water, oil, grease or other objectionable matter. Do not use solvent material that will damage pavements as cleaning agents. Immediately before painting, give pavement surfaces a final cleaning by means of a power broom and a power blower using compressed air following the brooming. C. Provide warning devices required to protect the painting operations and the finished work. 3.3 PAVEMENT MARKING A. Equipment: Apply the traffic and parking striping with a traffic stripe-painting machine with a compressor capacity of at least 105 cubic feet and capable of operating at an air pressure of 125 psi. Mechanically agitate paint while the machine is in operation. Equip the striping machine with a pointer so designed that the machine will hold exactly to the alignment. Equip the propelling vehicle with a speedometer or tachometer, and with a suitable device for determining the quantity of paint in the container. Thoroughly clean the paint container and spray nozzles on the machine before starting each day's work. 1. Equipment used for applying reflectorized striping shall be equipped with a bead dispenser capable of applying the beads at the specified rate. 2. Where the configuration or location of a traffic stripe is such that a striping machine is not suitable, use hand spraying equipment and stencils or templates. 3. Apply paint for word markings, letters, numerals, and symbols using hand spraying equipment and paint-resistant, die-cut stencils or templates, firmly secured to pavement. Mark an extended area beyond edges of each stencil to prevent paint application beyond the stencil. Apply paint so that it cannot run beneath the stencil B. Application: Immediately following the preparation of the pavement surface, apply the striping at the rate of 100 to 110 square feet per gallon of paint. Apply lines 4 inches wide Painted Pavement Markings
4 unless otherwise indicated. Apply the stripe of the indicated or specified width, with clean true edges and without sharp breaks. Repaint, to the applicable specifications, portions of the stripe damaged by any type of traffic within 24 hours after the stripe has been applied. 1. Provide International Symbol of Accessibility for each parking stall for the disabled at location indicated. Symbol shall be 36 inches square, white on standard blue background and shall conform to 2013 CBC Title 24 Part 2, Chapter 11B; and 2010 ADA Standards for Accessible Design. 2. Where reflectorized markings are shown, incorporate glass beads into the paint coating at the rate of not less than 5 pounds per gallon. Embed beads into the paint coating to a depth of one half their diameters. C. Tolerances: Apply striping within a tolerance of 1/2 inch in 50 feet. Apply markings and stripings to the widths indicated within a tolerance of 1/4 inch on straight sections and 1/2 inch on curved sections. D. At completion touch up stripes and markings which are not clear and distinct or which are not uniform in color. 3.4 PROTECTING AND CLEANING A. Protect pavement markings from damage and wear during remainder of construction period. B. Clean spillage and soiling from adjacent construction using cleaning agents and procedures recommended by manufacturer of affected construction. END OF SECTION 05/01/ Painted Pavement Markings
5 These paragraphs not used: C. Section Includes: Painted traffic striping and symbols and game markings on pavements and curbs. 1. Striping or other surface marking to identify the accessible path of travel from the edge of the public sidewalk on Mansell Street to the Upper Plaza. 2. Striping and identification at designated accessible parking stalls. 3. Restriping of (e) parking lots after repaving. 3.5 MATERIALS A. Pavement Marking Paint: Vinyl acrylic type for use on asphaltic concrete and portland cement concrete, colors as indicated, specified herein, or required by CBC Title 24 Part 2. Acceptable product or equal: Dunn-Edwards Corp.; W-801 Vin-L-Stripe Painted Pavement Markings
A. Testing Laboratory Services: Section B. Excavation, Site Fill and Rough Grading: Section Sub-Base Course Material (If requested).
SECTION 02500 - PART 1 - GENERAL 1.01 RELATED WORK SPECIFIED ELSEWHERE A. Testing Laboratory Services: Section 01411. B. Excavation, Site Fill and Rough Grading: Section 02200. C. Concrete: Section 03310.
More informationSECTION 14 - RESTORATION OF SURFACES TABLE OF CONTENTS
SECTION 14 - RESTORATION OF SURFACES TABLE OF CONTENTS Section Page SECTION 14 RESTORATION OF SURFACES... 14.1 14-1 GENERAL... 14.1 14-2 PRIVATE ROADS... 14.1 14-3 STREETS AND PARKING LOTS... 14.1 14-3.01
More informationSECTION 14 - RESTORATION OF SURFACES TABLE OF CONTENTS
SECTION 14 - RESTORATION OF SURFACES TABLE OF CONTENTS Section Page 14-1 GENERAL... 14.1 14-2 PRIVATE ROADS... 14.1 14-3 STREETS AND PARKING LOTS... 14.1 14-3.01 Aggregate Base... 14.1 14-3.02 Asphalt
More informationSECTION 2200 PAVING CITY OF BLUE SPRINGS, MISSOURI CONSTRUCTION SPECIFICATIONS
SECTION 2200 PAVING CITY OF BLUE SPRINGS, MISSOURI CONSTRUCTION SPECIFICATIONS The City of Blue Springs hereby adopts Section 2200 of the Kansas City Metropolitan Chapter of APWA Construction and Material
More information2014 Capital Project Phase 3 Grand Island Central School District Cannon Design Project No SECTION PAVING PART 1 - GENERAL
SECTION 321200 - PAVING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. The Contractor for this work shall be held to have read all of the Bidding Requirements, the Proposal Forms, the General Conditions of
More informationStanford University Facilities Design Guidelines SECTION SEAL COATS. C. Section : Traffic Striping and Pavement Markings
SECTION 32 12 36 SEAL COATS PART 1 GENERAL 1.1 RELATED WORK A. Section 31 10 00: Site Preparation B. Section 32 12 00: Flexible Paving C. Section 32 17 23 01: Traffic Striping and Pavement Markings 1.2
More informationITEM P-631 REFINED COAL TAR EMULSION WITH ADDITIVES, SLURRY SEAL SURFACE TREATMENT
9/30/2009 AC 150/5370-10E ITEM P-631 REFINED COAL TAR EMULSION WITH ADDITIVES, SLURRY SEAL SURFACE TREATMENT 631-1.1 GENERAL. This item shall consist of a mixture of refined coal tar emulsion, mineral
More informationSection 811. PERMANENT PAVEMENT MARKINGS
811.01 Section 811. PERMANENT PAVEMENT MARKINGS 811.01. Description. This work consists of providing and applying retroreflective permanent pavement markings in accordance with the Michigan Manual on Uniform
More informationSECTION FLEXIBLE PAVING
SECTION 321200 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. Include GENERAL CONDITIONS and applicable parts of Division 1 as part of this Section. B. Examine all Drawings and other Sections of the Specifications
More informationOKLAHOMA DEPARTMENT OF TRANSPORTATION SPECIAL PROVISIONS FOR TRAFFIC STRIPE (MULTI-POLYMER)
856-1(a-g) 09 OKLAHOMA DEPARTMENT OF TRANSPORTATION SPECIAL PROVISIONS FOR TRAFFIC STRIPE (MULTI-POLYMER) These Special Provisions revise, amend, and where in conflict, supersede applicable sections of
More informationCITY OF FORTUNA, CALIFORNIA
CITY OF FORTUNA, CALIFORNIA Community Development Department Building and Safety Division 621 11 th street Fortuna, California 95540 Phone: 707-725-7600 - Fax: 707-725-7610 ACCESSIBLE PARKING REQUIREMENTS
More informationSECTION HIGH DENSITY MINERAL BOND
SECTION 32 01 13.68 HIGH DENSITY MINERAL BOND PART 1 GENERAL 1.1. SECTION INCLUDES A. Mineral aggregate and asphalt binder slurry spread as a high density mineral bond seal coat over a roadway surface.
More informationBITUMEN-SET PRECAST CONCRETE PAVING SLABS
SECTION 32 14 13.16 BITUMEN-SET PRECAST CONCRETE PAVING SLABS (1995 MasterFormat Section 02784) NOTE: This guide specification is the U.S. for concrete paving slabs adhered with a neoprene mastic to a
More informationITEM 25 CHIP SEAL MATERIALS 2 A. Non-Polymer Modified Asphalt Emulsion (Fog Seal) 2 B. Polymer Modified Asphalt Emulsion Binder 2
ITEM 25 CHIP SEAL 25.1 DESCRIPTION 2 25.2 MATERIALS 2 A. Non-Polymer Modified Asphalt Emulsion (Fog Seal) 2 B. Polymer Modified Asphalt Emulsion Binder 2 25.3 AGGREGATES 3 25.4 MIX DESIGN 4 25.5 EQUIPMENT
More informationCEDAR RAPIDS METROPOLITAN AREA STANDARD SPECIFICATIONS FOR PUBLIC IMPROVEMENTS April 2003
SECTION 02850 PAVEMENT MARKINGS PART 1 GENERAL 1.01 - Section Includes A. Traffic Paint. B. Thermoplastic Reflectorized Pavement Markings. C. Permanent Marking Tape. D. Preformed Polymer Marking Material
More informationSECTION CURB RAMPS AND OTHER MINOR CONCRETE FACILITIES. Part 1 - General Work Included Related Requirements...
SECTION 02530 CURB RAMPS AND OTHER MINOR CONCRETE FACILITIES CONTENTS: Part 1 - General... 1 1.01 Work Included... 1 1.02 Related Requirements... 1 1.03 Inspection And Tests... 1 1.04 Quality Assurance...
More informationAsphalt Rubber Chip Sealing DRAFT MAINTENANCE SPECIFICATION. March 22, 2007
Asphalt Rubber Chip Sealing DRAFT MAINTENANCE SPECIFICATION March 22, 2007 Description: This work consists of furnishing and applying asphalt rubber binder followed by an application of treated cover aggregate
More informationSpecial Provision for Hot-Mix Asphalt Prime Coat
All Regional Engineers Omer M. Osman, P.E. Special Provision for Hot-Mix Asphalt Prime Coat July 25, 2014 This special provision was developed by the Bureau of Materials and Physical Research to improve
More informationITEM 6 CONCRETE CURBS, GUTTERS, AND SIDEWALKS
ITEM 6 CONCRETE CURBS, GUTTERS, AND SIDEWALKS 6.1 DESCRIPTION This work shall consist of constructing curbs, gutters, sidewalks, ramps, local depressions and driveways of the form and dimensions shown
More informationAsphalt Paving
University of New Hampshire University of New Hampshire Scholars' Repository Division 32 Exterior Improvements Chapter 5 Technical Construction and Renovation Standards 1-25-2013 321216 - Asphalt Paving
More information1. General Signs shall conform to Section 56, Signs, of the State Specifications, and these Specifications.
Section 32 TRAFFIC SIGNS, MARKINGS, AND BARRICADES 32-1 TRAFFIC SIGNS 1. General Signs shall conform to Section 56, Signs, of the State Specifications, and these Specifications. 2. Overhead Sign Structures
More informationSECTION 1045 PAINT FOR STRUCTURAL STEEL
SECTION 1045 PAINT FOR STRUCTURAL STEEL 1045.1 Paint and Paint Material. 1045.1.1 General. All single component paints shall be ready-mixed at the factory to comply with the specification formula for the
More informationREQUEST FOR PROPOSAL Asphalt & Concrete Repair
REQUEST FOR PROPOSAL 2017 Asphalt & Concrete Repair English Landing Elementary School Union Chapel Elementary School Lakeview Middle School Park Hill High School Prairie Point Elementary School Congress
More informationSample Specification
Sample Specification Section 02760 Paving Specialties StencilCoat Commercial Asphalt and Concrete Surfacing System 1.0 GENERAL 1.1 Summary The StencilCoat Commercial Asphalt Surfacing System is a 100%
More informationSECTION CONCRETE PAVING SLABS SET IN MORTAR
SECTION 32 14 13.16 CONCRETE PAVING SLABS SET IN MORTAR (1995 MasterFormat Section 02784) Note: This guide specification for the U.S. is for paving slabs mortared to a concrete base and grouted joints
More informationCAPE SEAL SPECIFICATIONS
CAPE SEAL SPECIFICATIONS DESCRIPTION The Contractor shall furnish all labor, equipment, material, supplies, environmental protection, no parks, raised markers, signage, traffic control, secondary sweeping,
More informationCITY OF SANTA ANA PROPOSAL PROJECT NO.: CHESTNUT AVE & BUSH/CYPRESS BIKE LANES FAID#: U58DP005861
PROPOSAL BID PROPOSAL TO: CITY COUNCIL OF THE CITY OF SANTA ANA FROM: REQUIREMENT: The undersigned bidder declares that they have carefully examined the location of the proposed work, that they have examined
More informationA. Texas Department of Transportation 2004 Standard Specifications for Construction and Maintenance of Highways, Streets and Bridges (TxDOT).
SECTION 32 01 16 ASPHALT OVERLAY PART 1 - GENERAL 1.1 SCOPE OF WORK A. This Section specifies the requirements for scarifying, grinding, sweeping and repair of existing asphalt concrete pavement to establish
More informationARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound
ARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound SECTION 03 01 30 MAINTENANCE OF CAST-IN-PLACE CONCRETE
More informationPAINTS AND ENAMELS. Package the paint in new containers marked with the following information:
PAINTS AND ENAMELS 3501 BASIC REQUIREMENTS FOR PAINTS 3501.1 SCOPE Provide paints for construction and maintenance. 3501.2 REQUIREMENTS A Package Stability Ensure the paint does not cake, liver, thicken,
More informationA. Texas Department Transportation 2004 Standard Specifications for Construction of Highways, Streets and Bridges (TxDOT):
SECTION 31 32 13.16 CEMENT STABILIZATION PART 1 GENERAL 1.1 SCOPE OF WORK A. This Section pertains to the specifications for cement stabilization of sandy or silty soil and consists of pulverizing, addition
More information610 - DOUBLE ASPHALT SURFACE TREATMENT SECTION 610 DOUBLE ASPHALT SURFACE TREATMENT
SECTION 610 DOUBLE ASPHALT SURFACE TREATMENT 610.1 DESCRIPTION Construct a wearing surface composed of an asphalt prime coat followed by the applications of 2 asphalt seal coats and cover material as specified
More information1301 SCOPE. This section covers asphaltic concrete (AC) pavement for roadways and parking areas.
SECTION 1300 - ASPHALTIC CONCRETE PAVEMENT 1301 SCOPE. This section covers asphaltic concrete (AC) pavement for roadways and parking areas. 1302 GENERAL. Pavement shall be constructed to the lines, grades,
More informationROOF BALLAST MATERIALS ARCHITECTURAL CONCRETE PAVING SLABS SRS LEVELING BLOCK SYSTEM INSTALLATION PART GENERAL 1.
07555 - ROOF BALLAST MATERIALS ARCHITECTURAL CONCRETE PAVING SLABS SRS LEVELING BLOCK SYSTEM INSTALLATION PART 1.00 - GENERAL 1.01 SUMMARY: A. The work of this section consists of furnishing and installing
More informationThe GREENBOOK 2015 Standard Specifications for Public Works Construction
203-3.4.4 Rubberized Polymer Modified Emulsion (RPME). 203-4.4.4.1 General. RPME shall consist of a mixture of emulsified asphalt, crumb rubber, and latex. RMPE shall contain between 0.55 pounds per gallon
More informationPAVEMENT MARKINGS. F. Grooves Cut for Pavement Markings, Symbols, and Legends
PAVEMENT MARKINGS PART 1 - GENERAL 1.01 SECTION INCLUDES A. Permanent Pavement Markings, Symbols, and Legends B. Removable Pavement Markings, Symbols, and Legends C. Temporary Delineators D. Raised Pavement
More informationVIRGINIA DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR LATEX MODIFIED EMULSION TREATMENT (MICRO-SURFACING)
S312EM2-1110 VIRGINIA DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR LATEX MODIFIED EMULSION TREATMENT (MICRO-SURFACING) August 10, 2010 I. DESCRIPTION This work shall include furnishing and placing
More informationSECTION BITUMINOUS CONCRETE PAVEMENT
SECTION 321216 BITUMINOUS CONCRETE PAVEMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationS-1 (2356) BITUMINOUS SEAL COAT REVISED 9/26/07 SP Mn/DOT 2356 is deleted and replaced by the following:
S-1 (2356) BITUMINOUS SEAL COAT REVISED 9/26/07 SP2005-136 Mn/DOT 2356 is deleted and replaced by the following: S-1.1 DESCRIPTION Construct a seal coat on a prepared surface. A seal coat is the application
More information507 SLURRY SEAL AND MICRO-SURFACING 1 of 8 CATEGORY 500 PAVING SECTION 507 SLURRY SEAL SECTION 507 SLURRY SEAL AND MICRO-SURFACING
507 SLURRY SEAL AND MICRO-SURFACING 1 of 8 CATEGORY 500 PAVING SECTION 507 SLURRY SEAL 489 DELETE: SECTION 507 SLURRY SEAL in its entirety. INSERT: The following. SECTION 507 SLURRY SEAL AND MICRO-SURFACING
More informationITEM 275 PORTLAND CEMENT TREATED MATERIALS (ROAD MIXED)
ITEM 275 PORTLAND CEMENT TREATED MATERIALS (ROAD MIXED) 275.1. Description. This Item shall govern for treating subgrade, new and/or existing base [with or without asphaltic concrete pavement (ACP)], or
More informationSECTION CONTROLLED LOW STRENGTH MATERIAL
SECTION 03300 CONTROLLED LOW STRENGTH MATERIAL PART 1 GENERAL 1.1 DESCRIPTION A. This Section specifies Controlled Low Strength Material (CLSM) to be used as described in this specification, including
More informationSKATE ON LAYKOLD Specification
Acrylic Sport & Recreational Surfaces SKATE ON LAYKOLD Specification PART 1 GENERAL 1.1 DESCRIPTION Scope: This guide specification covers the construction and installation for the SKATE ON LAYKOLD inline
More informationSection 505. CHIP SEALS
Section 505. CHIP SEALS 505.01. Description. This work consists of preparing the pavement surface and providing and placing a single chip seal, double chip seal, or shoulder chip seal. 505.02. Materials.
More informationSECTION CAST-IN-PLACE CONCRETE
SECTION 03300 CAST-IN-PLACE CONCRETE PART 1 GENERAL 1.01 SECTION INCLUDES A. The Contractor shall furnish all work and materials, including cement, sand and coarse aggregate, water, admixtures, curing
More informationProudly Made in the U.S.A.
5-Year Warranty Proudly Made in the U.S.A. Cast-In-Place (wet-set) 2 Cast-In-Place (wet-set) Tactile Proudly Made in the U.S.A. In stock colors White 37875 Brick Red 20109 Yellow 33538 Blue 15187 Safety
More informationPAVING SLABS ON A CONCRETE BASE
SECTION 32 14 13.16 PAVING SLABS ON A CONCRETE BASE (1995 MasterFormat Section 02784) Note: This guide specification for the U.S. is for paving slabs on a sand bed over concrete for pedestrian applications.
More informationAsphalt Maintenance PRODUCTS INFORMATION AND INSTALLATION GUIDE
Asphalt Maintenance PRODUCTS INFORMATION AND INSTALLATION GUIDE TABLE OF CONTENT About RESISTO 2 Asphalt Cleaner and Degreaser 3 Oil Spot Primer 3 Liquid Crack Filler 4 Rubberized Crack Filler 4 Levelling
More informationMunicipality of Waterville Public Sidewalk Repair Policy
Municipality of Waterville Public Sidewalk Repair Policy Purpose - The purpose of this policy is to protect the public health, safety and welfare of the citizens and inhabitants of the Municipality by
More informationSAMPLE SPECIFICATION
SAMPLE SPECIFICATION Section 02760 Paving Specialties ROADCOLOR Epoxy Modified Bike Lane Coating System IDEAL FOR VEHICULAR BIKE LANE, BIKE LANES, for ASPHALT and CONCRETE SURFACES 1.0 GENERAL 1.1 Summary
More informationPRODUCT GUIDE SPECIFICATION
PRODUCT GUIDE SPECIFICATION Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat,
More informationTEX COTE 600 TEXTURED COATING MASONRY PROTECTIVE COATING
SECTION 09960 - TEXTURED COATINGS Coating System Submittals Guide Specification TEX COTE 600 TEXTURED COATING MASONRY PROTECTIVE COATING (SPLIT FACE OR SAND FINISH BLOCK) 1. TEX COTE 600, Textured Coating
More informationStudent Services & Classroom Addition
SECTION 321216 - ASPHALT PAVING PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationCold-in-Place Recycling
Design Manual Chapter 5 - Roadway Design 5J - Pavement Rehabilitation Program 5J-2 Cold-in-Place Recycling A. General Cold-in-place recycling (CIR) is the process of recycling an asphalt pavement in-place
More informationItem P-629 Thermoplastic Coal Tar Emulsion Surface Treatments
Item P-629 Thermoplastic Coal Tar Emulsion Surface Treatments DESCRIPTION 629-1.1. This item shall consist of an application of a thermoplastic resin coal tar emulsion Spray Seal Coat applied to an existing,
More informationCONCRETE STEPS, HANDRAILS, AND SAFETY RAIL
SUDAS Standard Specifications Division 9 - Site Work and Landscaping Section 9080 - Concrete Steps, Handrails, and Safety Rail CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL PART - GENERAL.0 SECTION INCLUDES
More informationSECTION LAGUNA SERIES TOP HUNG SLIDING DOOR SYSTEM
Page 1 of 6 SECTION 08 32 20 LAGUNA SERIES TOP HUNG SLIDING DOOR SYSTEM USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS SLIDING DOORS. SECTION INCLUDES OVERHEAD SLIDING TUBE ASSEMBLY, MOUNTING
More informationGuideline Specification ACRYMAX ARS-1-C Reinforced Composite Elastomeric Membrane System for Concrete Roofs Fluid-Applied Roofing
221 Brooke Street Media, PA 19063 610-566-7470 Fax 610-891-0834 Website www.acrymax.com e-mail info@acrymax.com This document is intended to provide guidelines for the proper specification and application
More informationMDC MicroTex Eggshell Micro-Textured Ceramic Coating for Walls
MicroTex Eggshell Micro-Textured Ceramic Coating for Walls Specification Guide 95: 9770 Special Wall Finishes 88: 9800 Special Coatings Part 1 General 1.01 SUMMARY A. This section specifies the furnishing
More informationSection 1 OBC FADS /13 Access to Parking Areas
Section 1 OBC 3.8.2.2 4.3.12/13 Access to Parking Areas A barrier-free path of travel is provided from: a) the entrance to the exterior parking area b) at least one parking level where a passenger elevator
More information1.02 DESCRIPTION A. This Section specifies furnishing and installing Surface Applied Detectable/Tactile Warning Surface Tiles where indicated.
SURFACE APPLIED DETECTABLE/TACTILE WARNING SURFACE TILE PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Special Conditions and Division 1 Specifications
More informationSection 508. CHIP SEALS Description. Prepare the surface and apply the specified single chip seal, double chip seal or shoulder chip seal.
508.01 Section 508. CHIP SEALS 508.01 Description. Prepare the surface and apply the specified single chip seal, double chip seal or shoulder chip seal. 508.02 Materials. Use materials meeting the following.
More informationThe following specification refers to the Stepstone, Inc. product known as: Steptreads
The following specification refers to the Stepstone, Inc. product known as: Steptreads If you need any additional information please call Stepstone, Inc. at 800-572-9029 or visit our website www.stepstoneinc.com
More informationA Design Review of Waterproofing Codes
A Design Review of Waterproofing Codes Section 1807 of Chapter 18 of the International Building Code addresses waterproofing under the section title of Dampproofing and Waterproofing. The section defines
More informationFLEXIBLE PAVING. A. Full depth asphaltic concrete paving over prepared subgrade
FLEXIBLE PAVING PART 1 GENERAL 1.1 SECTION INCLUDES A. Full depth asphaltic concrete paving over prepared subgrade 1.2 REFERENCES A. ASTM C29: Unit Weight and Voids in Aggregate B. ASTM C88: Soundness
More informationADA APPROVED SURFACE APPLIED DETECTABLE WARNING SYSTEM
ADA APPROVED SURFACE APPLIED DETECTABLE WARNING SYSTEM PART 1 GENERAL 1. RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Special Conditions, apply to this Section.
More informationCONSTRUCTION STANDARDS SECTION CS 3 TRENCH FOUNDATION, BEDDING AND BACKFILL
CONSTRUCTION STANDARDS SECTION CS 3 TRENCH FOUNDATION, BEDDING AND BACKFILL CS 3-01 GENERAL: A. The foundation, bedding and backfill for all trenches shall conform with the requirements of the City Standard
More informationSECTION 633 PAVEMENT MARKERS DESCRIPTION
633 SECTION 633 PAVEMENT MARKERS DESCRIPTION 633.01.01 GENERAL A. This work shall consist of furnishing and placing pavement markers at the locations shown on the plans or where directed by the Engineer.
More informationCement Stabilized Soil (CSS) (Portland cement)
Cement Stabilized Soil (CSS) (Portland cement) 1.0 DESCRIPTION. This specification shall govern the process known as Cement Stabilized Soil (CSS). CSS consists of mixing the existing base, subbase and
More informationColor Stain 5100 System APPLICATION INSTRUCTIONS
Color Stain 5100 System APPLICATION INSTRUCTIONS SUPER-KRETE PRODUCTS REQUIRED: S-12000 Heavy Duty Degreaser S-1300 Pene-Krete S-9500 Color Stain SK-P5100 Clear Gloss or Clear Satin or SK-P5100 VOC Clear
More information550 Surface Treatments
Table of Contents 550 Surface Treatments... 550-1 550.1 Introduction... 550-1 551 Crack Sealing... 550-1 551.1 Project Selection... 550-1 551.2 Design Considerations... 550-1 552 Chip Sealing... 550-2
More informationfor Mortar-Set Concrete Tiling Installations
The following specification refers to the Stepstone, Inc. product known as: Large Scale CalArc Pavers for Mortar-Set Concrete Tiling Installations Large Scale CalArc Pavers are part of the California Architectural
More information1. Division 09 Section "Rough Carpentry."
GREENSPOINT AND LAUDER RD. EC/PRE-KlK PAGE 1 SECTION 096400 - WOOD FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary
More informationUNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-07 11 13 (August 2011) Change 1-05/17 --------------------------- Preparing Activity: NAVFAC Superseding UFGS-07 11 13 (April 2006) UNIFIED FACILITIES GUIDE SPECIFICATIONS
More informationPart 1 - General. Spec Component Sikadur 32 Hi-Mod. DIVISION 3 -CONCRETE Section Cast-in-Place Concrete Bonding Agents for Concrete
Spec Component 042-0101 Sikadur 32 Hi-Mod DIVISION 3 -CONCRETE Section 03300 Cast-in-Place Concrete Bonding Agents for Concrete Part 1 - General 1.01 Summary A. This specification describes the bonding
More informationSpecial Specification 3005 Scrub Seal Treatment
Special Specification 3005 Scrub Seal Treatment 1. DESCRIPTION 2. MATERIALS 3. EQUIPMENT Construct a surface treatment consisting of 1 or more applications of a single layer of asphalt emulsion that is
More informationSection 504. MICRO-SURFACING
504.01 Section 504. MICRO-SURFACING 504.01. Description. This work consists of preparing existing pavement and providing and placing a micro-surfacing mixture. 504.02. Materials. Provide materials in accordance
More informationSAMPLE SPECIFICATION
SAMPLE SPECIFICATION Section 02760 Paving Specialties STREETCOAT Epoxy Modified Traffic Coating System IDEAL FOR VEHICULAR TRAFFIC, BIKE LANES AND COATING STAMPED ASPHALT SURFACES 1.0 GENERAL 1.1 Summary
More informationSECTION INTERLOCKING CONCRETE PAVERS
SECTION 23 14 13 INTERLOCKING CONCRETE PAVERS (1995 MasterFormat Section 02780) Note: This guide specification for concrete paver applications in the U.S. for concrete pavers and bedding sand over a compacted
More informationExtraction and Sieve Analysis ( µm minus) Forming Marshall Specimens, Field Method
3.56 COLD IN-PLACE RECYCLING 3.56.1 GENERAL This specification covers the requirements for Cold In-Place Recycling (CIR) which consists of reclaiming the existing asphalt pavement; sizing the reclaimed
More informationSUPPLEMENTAL SPECIFICATION HIGH PERFORMANCE CHIP SEAL
May 21, 2008 HIGH PERFORMANCE CHIP SEAL 411 High Performance Chip Seal 411.1 Description High Performance Chip Seal is a high macro-texture surface treatment that is applied in a continuous operation.
More informationSECTION 26 - COLD PLANE ASPHALT CONCRETE PAVEMENT TABLE OF CONTENTS
SECTION 26 - COLD PLANE ASPHALT CONCRETE PAVEMENT TABLE OF CONTENTS Section Page 26-1 GENERAL... 26.1 26-2 PAVEMENT KEYCUTTING... 26.1 26-3 PAVEMENT PLANING... 26.2 26-4 PLANED PAVEMENT CONFORMS... 26.3
More informationHARD COURT/RUNNING TRACK CONSTRUCTION. A. Section Includes: Tennis courts, basketball/volleyball courts, and running tracks.
PART 1 GENERAL 1.01 SUMMARY SECTION 02545 HARD COURT/RUNNING TRACK CONSTRUCTION A. Section Includes: Tennis courts, basketball/volleyball courts, and running tracks. B. Related Sections: 1. 02200 - Earthwork.
More informationCONSTRUCTION SPECIFICATION FOR UNTREATED GRANULAR, SUBBASE, BASE, SURFACE SHOULDER AND STOCKPILING
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 314 DECEMBER 1993 CONSTRUCTION SPECIFICATION FOR UNTREATED GRANULAR, SUBBASE, BASE, SURFACE SHOULDER AND STOCKPILING 314.01 SCOPE 314.02 REFERENCES
More informationSection PANEL SIGNAGE
Section 10 14 23 PANEL SIGNAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including FDOT DIVISION I GENERAL REQUIREMENTS & COVENANTS Specification Sections,
More informationItem P-629 Thermoplastic Coal Tar Emulsion Surface Treatments Micro-Surface Type A
Item P-629 Thermoplastic Coal Tar Emulsion Surface Treatments Micro-Surface Type A DESCRIPTION 629-1.1. This item shall consist of an application of a Thermoplastic Resin Coal Tar Emulsion Micro- Surface,
More informationCity of Brandon Division 2 Standard Construction Specifications Section January 2000 Page 1 of 10 SOIL CEMENT BASE COURSE PART 1 GENERAL
January 2000 Page 1 of 10 PART 1 GENERAL 1.01 OTHER CONTRACT DOCUMENTS 1.02 DESCRIPTION OF WORK 1.03 RELATED WORK 1.04 APPROVALS PART 2 PRODUCTS 2.01 CEMENT 2.02 WATER The General Conditions of the Contract,
More informationNarrow Modular Pavers (NMP) for Mortar-Set Concrete Tiling Installations
The following specification refers to the Stepstone, Inc. product known as: Narrow Modular Pavers (NMP) for Mortar-Set Concrete Tiling Installations Narrow Modular Pavers are part of the California Architectural
More informationSACRAMENTO COUNTY ASPHALT RUBBER HOT MIX-GAP GRADED (ARHM-GG):
SACRAMENTO COUNTY ASPHALT RUBBER HOT MIX-GAP GRADED (ARHM-GG): ARHM-GG shall conform to the provisions for Type "A" asphalt concrete in Section 39, "Asphalt Concrete," of the State Standard Specifications
More informationSECTION TERRAZZO FLOOR TILE
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 66 16 SPEC WRITER NOTES: 1. Use this section only for NCA projects. 2. Delete between // ----- // if not applicable to project. Also delete any other item or
More informationA. Section Includes: SpectraPour Poured-in-Place Playground Surfacing System
SpectraPour Poured-in-Place Specification SpectraTurf 500 E. Rincon Street #100 Corona, CA 92879-1352 Phone: (800) 875-5788 Fax: (951) 734-3630 E-mail: info@spectraturf.com www.spectraturf.com PART 1 GENERAL
More informationTECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS ITEM 00663 TRAFFIC BUTTONS & PAVEMENT MARKERS 663.1 Description. This item shall consist of furnishing and installing traffic buttons and reflectorized pavement markers and jiggle
More informationMANUFACTURER S (SHORT FORM) SPECIFICATION / SECTION
STUC-O-FLEX - ELASTOMERIC ACRYLIC FINISH APPLICATION TO PORTLAND CEMENT PLASTER / CONCRETE RENDER MANUFACTURER S (SHORT FORM) SPECIFICATION / SECTION 09220-09 24 00 PART 1-GENERAL SCOPE: Manufacturer's
More informationCONCRETE POLISHING SPECIFICATION NEW OR EXISTING CONCRETE
CONCRETE POLISHING SPECIFICATION NEW OR EXISTING CONCRETE PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division
More informationSeries - 1
SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word
More informationSECTION High Performance Coatings Field Applied Acrylic Urethanes (Solid Color, Pearl and Metallic Finishes)
- 1 - SECTION 099600 High Performance Coatings Field Applied Acrylic Urethanes (Solid Color, Pearl and Metallic Finishes) PART 1 GENERAL 1.1 SECTION INCLUDES A. Systems for field applied acrylic urethane
More informationFIVE STAR PRODUCTS, INC. (800)
FIVE STAR PRODUCTS, INC. www.fivestarproducts.com (800) 243-2206 Page 1 of 11 DESIGN-A-SPEC GUIDELINES FIVE STAR RS ANCHOR GEL CONTENTS PART A - GENERAL CONDITIONS PART B - MATERIAL SPECIFICATIONS PART
More informationELASTOFLEX ELASTOMERIC TEXTURED ACRYLIC WALL COATING SPECIFICATION
ELASTOFLEX ELASTOMERIC TEXTURED ACRYLIC WALL COATING SPECIFICATION PART 1 - GENERAL 1.01 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions,
More informationSECTION PANEL SIGNAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 10 14 23 - PANEL SIGNAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSPECIAL PROVISIONS - SP2014 BOOK Page 1 October 8, 2013
SPECIAL PROVISIONS - SP2014 BOOK Page 1 S-1 (2104) REMOVE AND REPLACE BITUMINOUS PAVEMENT (ADA) Always include SP2014-119 (PLANT MIXED ASPHALT PAVEMENT) or SP2014-121 (PLANT MIXED ASPHALT PAVEMENT FOR
More information