Rinnai Infinity XR26/HD200 Internal Flueing
|
|
- Amanda Simpson
- 6 years ago
- Views:
Transcription
1 Flueing Options and Rinnai Flue Kits Available Rinnai have developed two flueing kits to make installation of Rinnai Infinity XR26i/XR26ia and HD200i Internal units as easy as possible. Use the kit options (more economical than purchasing individual components) as a starting point and customise by ordering additional components as required. The exception will be for an application that starts horizontally and ends vertically or vice versa. This installation is defined as combination vertical/horizontal flueing and will require flueing components to be purchased separately. Basic Methods of Installation Direct Flueing For installations where the Rinnai Infinity is mounted directly on the inside of an external wall and where the flue centreline is less than 761mm/665mm from the outside face of a suitable external wall. Flue Kit Available: FFKITF Horizontal Extension Flueing The same as Direct Flueing but additional pipe is required due to the longer horizontal distance. Flue Kit Available: FFKITF + Vertical Straight Flueing For installations where the Rinnai Infinity needs to be flued vertically through the roof. Flue Kit Available: FFKITVERT + (as required) Combination Vertical/ Horizontal Flueing Is a combination of all the above and will require flueing components to be ordered separately.
2 General Guidelines for Flueing Internal Units Total flue length Flue dip switch Installations can consist of both horizontal and vertical runs to a maximum length of 9 metres, incorporating a maximum of three 90 bends. Flue dip switch, if flue length exceeds 2m, dip switch 1 of SW1 is to be switched to the OFF position. This increases the combustion speed to overcome the additional friction losses. Flue Length Dipswitch Settings Short Flue: Total flue length less than 2 metres Extended Flue: Total flue length 2 metres or greater Dipswitches SW1 SW SW Dipswitches SW2 SW SW Free flow of air required around For a balanced flue to operate safely and effectively there must be a free flow of air around the. For horizontal direct flueing this generally means being open on two sides with a minimum overhang above. Pipe asthetics Condensate Aesthetics can be a consideration for installation and often we receive queries on painting the white PVC piping. This can be done, first prime with etch primer suitable for PVC before painting with desired colour. Horizontal flues must slope 20mm per metre to the termination point. Ensure condensate drains appropriately. This is particularly relevant to longer horizontal runs where more condensate is produced. Multiple installations Rinnai New Zealand 2 of 6 XR26i/XR26ia/HD200 Interim Flueing Pages: 01-08
3 Direct Flueing Using FFKITF Suitable for; Rinnai Infinity XR26i, XR26ia and HD200i. or (Optional) 127mm Hole or (Optional) 127mm Hole For installations where the Rinnai Infinity is mounted directly on the inside of an external wall and where the flue centreline is less than maximum limits displayed. Drain Tube Cap Drain Tube Cap Contains: FSBEND Starter Bend External Wall Plate Ceiling Ring Horizontal Flue Terminal 761mm maximum 45 minimum 665mm maximum 761mm and 665mm is the maximum length from the flue centreline to the outside face of the wall Horizontal Extension Flueing Suitable for; Rinnai Infinity XR26i, XR26ia and HD200i. When the water heater is mounted against an internal wall and flueing needs to be extended for a longer distance horizontally to exit an external wall. (20mm per metre) Total flue length can be 9m. Drain Tube Cap Use FFKITF as a starting point and customise with. More than one flue pipe may be required.
4 UP UP UP UP Rinnai Infinity XR26/HD200 Internal Flueing Vertical Straight Flueing Using FFKITVERT Suitable for; Rinnai Infinity XR26i, XR26ia and HD200i. For installations where the Rinnai Infinity needs to be flued vertically through the roof. Additional lengths of can be added as required. For shorter installations, i.e. ceiling cavities, can be cut to length. Total flue length can be 9m. Minimum clearance 500mm Decktite or lead collar flushing Contains: Flue Pipe 1000mm Vertical Flue Terminal Drain Tube 500mm clearance shown is for simple roof pitches. Complex multiple pitched roofing can interfere with correct flueing of the appliance and greater clearances to flue s may be required. Refer to Rinnai Specification Service for further information. Shorter vertical flueing, air intake to go 500mm clear of the roof line. The top of the Infinity would have to be no higher than 860mm from the outside of the roof (for a fairly flat roof). For a steeper pitched roof the Infinity would need to be higher. Combination Vertical/Horizontal Flueing Suitable for; Rinnai Infinity XR26i, XR26ia and HD200i. Combination of both vertical and horizontal flueing. If starting horizontally and finishing horizontally then use FFKITF as a starting point and customise with parts listed below. Minimum clearance 500mm Decktite or lead collar flushing If starting horizontally and ending vertically or vise versa, individual components will need to be ordered. It must start with an or an. To finish there must be a for horizontal terminations or for vertical terminations. Total flue length can be 9m incorporating a maximum of three 90 bends. Contains: Vertical Roof Terminal External Wall Plate Ceiling Ring Horizontal Flue Terminal Flue Pipe 1000mm 45 o Bends Starter Bend Drain Tube 2 fall to trap Terminal
5 UP Rinnai Infinity XR26/HD200 Internal Flueing Flueing Components All flueing components have zero clearance from combustibles. Starter Bend Starter bend used as the starting component in either direct or combination flueing installations. Ø127 Wall penetration Min o Bends Used to create flueing offsets for combination flueing Supplied as 2 x 45 o bends Maximum of three 90 o bends can be used 64.5 (2x 45 Bends) (As a 90 OFFSET) (As a 45 OFFSET) Horizontal Flue Terminal Flue component used to terminate horizontal installations. Flue pipe and incorporated, can be cut to length. Includes: drain tube silicone lubricant Flue Pipe 1000mm PVC pipe, can be cut to length. Includes wall bracket Ceiling Ring Round trim plate for inside wall. 225 Thickness 1mm
6 Flueing Components External Wall Plate 20 Ø6 x 4 Square trim plate for outside wall Thickness 1mm Vertical Roof Terminal Flue component used to terminate vertical installations. Flue pipe and incorporated. Includes: drain tube silicone lubricant wall bracket Male 26/HD200 Internal Flue Spigot Retrofit male flue spigot for when: Old flueing has been installed and a new XR26i/XR26ia/HD200i unit has been purchased 1 When an older unit (with previous model flie kits) needs to be replaced with a new model 1 Newer models can be determined by the REU numbers displayed on the data plate of each Rinnai Infinity Rinnai New Zealand 6 of 6 XR26i/XR26ia/HD200 Interim Flueing Pages: 01-08
Technical and Dimensional Data. Saf-T Vent SC
Technical and Dimensional Data Saf-T Vent SC 3"/5" & 4"/7" Concentric Reduced Clearance Double Wall for Special Gas Vent and/or Sealed Combustion Systems Copyright 2003 Saf-T Vent is a registered trademark
More information150MM FREE STANDING WOOD FIRE FLUE KIT MKIII INSTALLATION INSTRUCTIONS
150MM FREE STANDING WOOD FIRE FLUE KIT MKIII INSTALLATION INSTRUCTIONS WARNING: THIS FLUE KIT HAS BEEN MANUFACTURED IN ACCORDANCE WITH AS/NZS 2918:2001 AND TESTED TO APPENDIX F. TO ENSURE SAFETY THIS FLUE
More information150MM FREE STANDING WOOD FIRE FLUE KIT MKIII INSTALLATION INSTRUCTIONS
150MM FREE STANDING WOOD FIRE FLUE KIT MKIII INSTALLATION INSTRUCTIONS WARNING: THIS FLUE KIT HAS BEEN MANUFACTURED IN ACCORDANCE WITH AS/NZS 2918:2001 AND TESTED TO APPENDIX F. TO ENSURE SAFETY THIS FLUE
More information150MM FREE STANDING WOOD FIRE FLUE KIT MKIII INSTALLATION INSTRUCTIONS
ULEB 150MM FREE STANDING WOOD FIRE FLUE KIT MKIII INSTALLATION INSTRUCTIONS WARNING: THIS FLUE KIT HAS BEEN MANUFACTURED IN ACCORDANCE WITH AS/NZS 2918:2001 AND TESTED TO APPENDIX F. TO ENSURE SAFETY THIS
More informationFlue gas systems for oil and gas condensing boilers. Flue gas kit DN60 rigid in the duct. Accessories DN60 (additionally available to gas flue kit)
Flue gas kit DN60 rigid in the duct 100193 Flue gas kit No Outlet set plastic 1 x Set 100193 39.10 (Quantities in the image differ from the set) 1003253 1001938 Spacer set * ( pieces) Top inspection opening
More information40CDi conventional. RD 537i. Installation Instructions for Flue Duct Kit AZB 873/1 Vertical Flue Terminal Assembly Ø 60/100 mm Ø135
Installation Instructions for Flue Duct Kit AZB 873/1 Vertical Flue Terminal Assembly Ø 60/100 mm 7 719 002 430 Ø100 Ø62 1140 116 3x Ø135 2x Ø100 4x 6 720 611 739-00.1O for Gas Condensing Boilers: R 29
More informationAir flue duct for use with ecotec boilers
For the installer Flue installation instructions Air flue duct for use with ecotec boilers Concentric System Ø 80/5 (Galvanized steel air duct/plastic flue duct) GB Contents Notes on the documentation
More informationfemale pipe. A Wall Support must be installed just above the tee and at least every 8 feet thereafter. If the pipe is to be run through a roof overhang then a Flashing, Storm Collar and Vertical Rain Cap
More informationFlue Accessories & Fitting Guide Ø 60/100 Flue Systems Ø 80/125 Flue Systems Ø 80/80 Twin Flue Systems Plume Displacement Kit (Ø 60/100 Flue Systems)
GUIDANCE NOTES Flue Accessories & Fitting Guide Ø 6/1 Flue Systems Ø 8/125 Flue Systems Ø 8/8 Twin Flue Systems Plume Displacement Kit (Ø 6/1 Flue Systems) READ THESE INSTRUCTIONS IN CONJUNCTION WITH THE
More informationINSTALLATION MANUAL CO-AXIAL HORIZONTAL FLUE KIT FOR SEELEY INTERNATIONAL BRAEMAR ECO-SUPERSTAR SH18, SH25 & WF25 HEATERS
INSTALLATION MANUAL CO-AXIAL HORIZONTAL FLUE KIT FOR SEELEY INTERNATIONAL BRAEMAR ECO-SUPERSTAR SH18, SH25 & WF25 HEATERS This Braemar Eco-SuperStar Heater Flue Kit must be installed in accordance with
More informationGas Fireplaces. P33-10/P33E-10 Gas Fireplace P33 DIMENSIONS WITH VIGNETTE FACEPLATE CLEARANCES WITH VIGNETTE FACEPLATE
Model P33-NG10 P33-LP10 P33E-NG10 P33E-LP10 Fuel Type Natural Gas Propane Natural Gas Propane Minimum Supply Pressure 5 W.C. (1.25 kpa) 11 W.C. (2.74 kpa) 5 W.C. (1.25 kpa) 11 W.C. (2.74 kpa) Manifold
More informationRegency Horizon HZ30E Gas Fireplace
Specifications: Framing Dimensions: Model HZ3E-NG HZ3E-LP Fuel Type Natural Gas Propane Gas Minimum Supply Pressure Manifold Pressure - High Approved Venting Systems Flex Vent Systems: Rigid Pipe Vent
More informationINSTALLATION INSTRUCTIONS OPERATION AND MAINTENANCE MANUAL Models event SD, event, Event Plus, and event Plus2 (Condensing Boiler Systems)
C US INSTALLATION INSTRUCTIONS OPERATION AND MAINTENANCE MANUAL Models event SD, event, Event Plus, and event Plus2 (Condensing Boiler Systems) A MAJOR CAUSE OF VENT RELATED FIRES IS FAILURE TO MAINTAIN
More informationBALCONY FLUE OUTLET KIT
BLCONY FLUE OUTLET KIT LOGIC Combi LOGIC + Combi LOGIC Heat LOGIC + Heat LOGIC System LOGIC + System LOGIC Code Combi i-mini When replacing any part on this appliance, use only spare parts that you can
More informationGas Fireplaces. P36D-10 Gas Fireplace. Unit Dimensions With Vignette Faceplate. *** Important: Framing height requires consideration of the hearth
28-15/16 (735mm) Model P36D-NG10 P36D-LP10 Fuel Type Natural Gas Propane Gas Fireplaces Minimum Supply Pressure Manifold Pressure - High Manifold Pressure - Low 5 W.C. (1.25 kpa) 3.8 W.C. (0.95 kpa) 1.1
More informationP36-10 / P36E-10 Gas Fireplace. 11 W.C. (2.74 kpa) 10 W.C. (2.49 kpa) 6.4 W.C. (1.59 kpa) 22,000 BTU/h (6.44 kw) 28,500 BTU/h (8.
Model P36-NG10 P36-LP10 P36E-NG10 P36E-LP10 Fuel Type Natural Gas Propane Natural Gas Propane Gas Fireplaces P36-10 / P36E-10 Gas Fireplace Minimum Supply Pressure 5 W.C. (1.25 kpa) 12 W.C. (3.00 kpa)
More informationRediflow Concrete Gas Flue System
Rediflow Concrete Gas Flue System Rediflow Concrete Gas Flue System Rediflow the complete gas flue block system Red Bank s range of Rediflow pre-cast concrete gas flue block system manufactured to BS EN
More informationFLUE KIT INSTALLATION MANUAL
FLUE KIT INSTALLATION MANUAL 7 76 9 55 ROOM SEALED TELESCOPIC FLUE 7 76 9 086 PLUME MANAGEMENT SYSTEM GREENSTAR 60/00 HORIZONTAL FLUE FOR USE WITH WORCESTER GREENSTAR GAS-FIRED APPLIANCES: Greenstar FS
More informationOuter Skin Kit & Flue: IB600, IB850, IB1100 Installation Manual
Outer Skin Kit & Flue: IB600, IB850, IB1100 Installation Manual Please see IB series product installation guide for details of installing the gas fire into this preformed metal cavity. Important: The appliance
More informationInstallation Instructions
Installation Instructions Flue Gas System Basic Kit GA-K - Chimney Flue Gas System for GB125 Oil Condensing Boiler For trained and certified installers Please read carefully prior to installation. 6 720
More informationLOGIC FLUE & ACCESSORIES GUIDE.
& ACCESSORIES GUIDE. COMBI C COMBI ESP1 + COMBI C SYSTEM S + SYSTEM S HEAT H + HEAT H CODE COMBI ESP1 WWW.IDEALBOILERS.COM This manual is for guidance only and must be read in conjunction with the Installation
More informationP36 - P36D Zero Clearance Direct Vent Gas Fireplace. 12 W.C. (3.00 kpa) 11 W.C. (2.74 kpa) 2.9 W.C. (0.72 kpa) 15,000 BTU/h (3.
P36 - P36D Zero Clearance Direct Vent Gas Fireplace Model P36-NG4 P36-LP4 P36D-NG1 P36D-LP1 Fuel Type Natural Gas Propane Natural Gas Propane Minimum Supply Pressure 5 W.C. (1.25 kpa) 12 W.C. (3. kpa)
More informationLOGIC FLUE & ACCESSORIES GUIDE.
& ACCESSORIES GUIDE. COMBI C COMBI ESP1 + COMBI C SYSTEM S + SYSTEM S HEAT H + HEAT H CODE COMBI ESP1 WWW.IDEALBOILERS.COM This manual is for guidance only and must be read in conjunction with the Installation
More informationGREENSTAR OILFIT FLUE RS
FLUE KIT INSTALLATION INSTRUCTIONS 7 76 90 06 ROOM SEALED 80/mm STANDARD TELESCOPIC FLUE 7 76 90 06 ROOM SEALED 80/mm SHORT TELESCOPIC FLUE 7 76 90 09 80mm PLUME MANAGEMENT SYSTEM 7 76 90 0 ROOM SEALED
More informationP36 / P36E Gas Fireplace. 11 W.C. (2.74 kpa) 10 W.C. (2.49 kpa) 6.4 W.C. (1.59 kpa) 22,000 BTU/h (6.44 kw) 28,500 BTU/h (8.35 kw)
P36 / P36E Gas Fireplace Model P36-NG10 P36-LP10 P36E-NG10 P36E-LP10 Fuel Type Natural Gas Propane Natural Gas Propane Minimum Supply Pressure 5 W.C. (1.25 kpa) 12 W.C. (3.00 kpa) 5 W.C. (1.25 kpa) 11
More informationPlease consult the manufacturer s installation manual for all details and requirements before making a final design layout decision.
Please consult the manufacturer s installation manual for all details and requirements before making a final design layout decision. 72" Direct Vent Gas Fireplace MODEL FRONT HEIGHT WIDTH FRONT BACK WIDTH
More informationDuraPlus. All-fuel, triple-wall chimney system. UL 103 HT.
DuraPlus ll-fuel, triple-wall chimney system. UL 103 HT. Specifications pplications DuraPlus himney is a triple-wall, all-fuel chimney for use with wood stoves, fireplaces, furnaces, boilers, stoves, ranges,
More informationAPPENDIX "B" November 5, 2002 Page 1 of 6 BOILERSMITH LTD. STACKS AND BREECHING
APPENDIX "B" November 5, 2002 Page 1 of 6 BOILERSMITH LTD. STACKS AND BREECHING NOTE The Stack and Breeching shall be installed in conformance with national, regional and local codes and standards and/or
More informationSI T T FST
SI 440-600-700-700T-780-780T-900-1100 Freestanding TAPER TOP Open Fire - Wood Burner Installation Instructions Note: FLUE SYSTEMS Casing. Flue System may require to be Doubled Lined to Comply. Ref ASNZS:2918:2001
More informationSimpson Dura-Vent Engineered Excellence
DuraPlus Simpson Dura-Vent Engineered Excellence pplications DuraPlus himney is a triple-wall, all-fuel chimney for use with wood stoves, fireplaces, furnaces, boilers, stoves, ranges, water heaters, or
More informationInstallation instructions
Installation instructions for contractors Flue gas system for Vitocrossal (type CU3), Vitodens and Vitoladens Safety instructions Please follow these safety instructions closely to prevent accidents and
More informationINSTALLATION MANUAL CO-AXIAL VERTICAL FLUE KIT FOR SEELEY INTERNATIONAL BRAEMAR ECO-SUPERSTAR SH18, SH25 & WF25 HEATERS
INSTALLATION MANUAL CO-AXIAL VERTICAL FLUE KIT FOR SEELEY INTERNATIONAL BRAEMAR ECO-SUPERSTAR SH18, SH25 & WF25 HEATERS Employers and Employees Responsibility The installation and maintenance of gas space
More informationTC54. for architects & designers. Dimensions Clearances Venting
for architects & designers TC54 Series D Dimensions Clearances enting IMPORTANT This booklet is intended as a basic specification guide for architects, designers and builders. Please refer to the Instruction
More informationNatural Gas Service Installation and Meter Clearance Requirements
Natural Gas Service Installation and Meter Clearance Requirements Call SJG s new construction line at 1-844-611-5605 for more information. Builder/Owner/Developer Requirements The clearances in this handout
More informationConcentric Vent/Air System Supplement
Concentric Vent/Air System Supplement This document is intended to be used by a qualified heating contractor or service technician. Read all instructions within this document and within the CHAL- LENGER
More informationoptional parts for geberit Duofix carrier
geberit Duofix carrier.335.00.5 Installation accessories for concealed tank and carrier for wall-hung toilet. Accessories shall be for alternate frame installation and connection sets between carrier and
More informationNEW CODE DESCRIPTION PART NO LIST PRICE CODE DESCRIPTION PART NO LIST PRICE LIST PRICES EFFECTIVE. Vogue. F & P Wholesale.
80 BOILERS NATURAL GAS Ideal Vogue Combi Ideal Vogue System CODE DESCRIPTION PART NO CURRENT LIST LIST PRICE PRICES CODE DESCRIPTION PART NO CURRENT LIST LIST PRICE PRICES COMBI OCTOBER 2016 NOVEMBER 2016
More informationInstallation instructions
Installation instructions Holetherm Double-walled flue gas discharge system (DW) 2016 All information in this release is subject to misprints. No liability is accepted for the consequences of misprints.
More informationGas Fireplaces. P33 Zero Clearance Direct Vent Gas Fireplace. *** Important: Framing height requires consideration of the hearth
P33 Zero Clearance Direct Vent Gas Fireplace P33 WITH THE FLUSH OR BAY FRONT Model P33-NG4 P33-LP4 Fuel Type Natural Gas Propane Minimum Supply Pressure 5 W.C. (1.25 kpa) 12 W.C. (3.00 kpa) Manifold Pressure
More informationInstallation Instructions. PolyPro Double-Wall Flex Gas Vent System for Category II & IV Gas-Burning Appliances. PolyPro Flex
Installation Instructions PolyPro Double-Wall Flex Gas Vent System for Category II & IV Gas-Burning Appliances PolyPro Flex A MAJOR CAUSE OF VENT RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES
More informationNouveau BBQ Single Flue
Nouveau BBQ 900-1100-1250-1500 Single Flue Outdoor BBQ Cooking Fire Wood Burner Installation Instructions FLUE SYSTEMS Casing. Flue system may require to be doubled lined to comply. Ref ASNZS:2918:2001
More informationA. Provide floor drains in all restrooms placed a minimum of 7 from back of wet wall, janitor closets, and mechanical rooms.
SECTION 22 13 00 FACILITY SANITARY SEWERAGE PART 1 - GENERAL 1.1 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design.
More informationBosch 4000S Internal Room-sealed continuous flow water heater and flue components
Bosch 4000S Internal Room-sealed continuous flow water heater and flue components Australian Models The Bosch 4000S Internal offers: 3 6 Star efficiency 3 Room sealed appliance 3 Inbuilt temperature controller
More informationHeat only boiler Potterton Promax HE Plus
Heat only boiler Potterton Promax HE Plus You can rely on Potterton The ultimate in reliability and service With Potterton on your side, you can be sure that you re offering your customers the ultimate
More informationHeat only boiler. Potterton Promax HE Plus
Heat only boiler Potterton Promax HE Plus You can rely on Potterton The ultimate in reliability and service With Potterton on your side, you can be sure that you re offering your customers the ultimate
More informationDur aflex stainless steel
Dur aflex stainless steel Simpson Dura-Vent Engineered Excellence DuraFlex SW DuraFlex SW is a smooth inner-wall, flexible stainless steel chimney liner. The smooth inner wall provides for no output reduction
More informationRSH ENGINEERING, INC. FINAL WALK THROUGH INSPECTION REPORT INSP#: S05092 DATE:08/27/06 PAGE #: 1 Address: 1234 Anywhere St, Anywhere, TX
PAGE #: 1 1 2 3 4 FRONT VIEW OF HOUSE INSPECTED SEE PIC. # 3 TO PIC. # 15 FOR DETAILS THE SPRINKLER HEAD IS BROKEN OFF AND SOIL HAS WASHED OUT FROM BASE OF SLAB. REPAIR SPRINKLER AND REPLACE THE SOIL.
More informationConcentric Vent/Air System Supplement
Concentric Vent/Air System Supplement This document is intended to be used by a qualified heating contractor or service technician. Read all instructions within this document and within the CHAL- LENGER
More informationICC - Model VIP+ Positive Pressure Chimney System and Grease Duct
Scope and Recommendations ICC - Model VIP+ Positive Pressure Chimney System and Grease Duct INSTALLATION AND MAINTENANCE INSTRUCTIONS The ICC Model VIP+ is a double wall construction listed venting system
More informationFlue Pipe Considerations
Flue Pipe Considerations Objective The application summary outlined here will communicate the necessary flue piping arrangement for EnergyLogic (EL) furnaces and boilers and give a fundamental understanding
More informationSlim-Line Heat only boiler. Potterton Promax HE Plus (SL)
Slim-Line Heat only boiler Potterton Promax HE Plus (SL) You can rely on Potterton The ultimate in reliability and service With Potterton on your side, you can be sure that you re offering your customers
More informationMULTILINE FLUE KIT EVOMAX P - 80P
MULTILINE FLUE KIT EVOMAX 30-150 30P - 80P When replacing any part on this appliance, use only spare parts that you can be assured conform to the safety and performance specification that we require. Do
More informationInoxSabiana 25 Flues. Stainless Steel Double Wall
Cert. n 0545/5 Flues Stainless Steel Double Wall Introduction and main constructional characteristics Double Wall, Stainless Steel Flues The is the result of innovative development based on over 0 years
More informationSECTION PLUMBING PIPING SYSTEM
SECTION 15410 - PLUMBING PIPING SYSTEM PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Basic Requirements: Provisions of Section 15010, BASIC MECHANICAL REQUIREMENTS, are a part of this Section. 1.02 SUMMARY
More informationDuraFlex. Flexible stainless steel relining for masonry chimney. UL 1777 and ULC S635.
DuraFlex Flexible stainless steel relining for masonry chimney. UL 1777 and ULC S635. Specifications DuraFlex SW Applications DuraFlex SW smooth wall flexible relining for masonry chimney. Use with gas,
More informationTCWS54 FOR ARCHITECTS & DESIGNERS SERIES D2. Dimensions Clearances Venting
FOR ARCHITECTS & DESIGNERS TCWS54 SERIES D2 Dimensions Clearances enting IMPORTANT This booklet is intended as a basic specification guide for architects, designers and builders. Please refer to the Instruction
More informationCounty of Yolo Development Services Building Inspection Division
County of Yolo Development Services Building Inspection Division 292 W. Beamer Street Woodland, CA. 95695 www.yolocounty.org (530) 666-8775 Mechanical Plan Review Comments Plan Review No. Owners Name Job
More informationViking Enviroclad Waterproofing Membrane. EC01 Enviroclad Drip Edge Specify from the above three options
*lum ngle 50x50x1.6mm min. with 20mm lum fixing bar to mechanically secure membrane Enviroclad Waterproofing Membrane Substrate to comply with current Roofspec Masterspec specification Substrate Checksheet
More informationRegency Bellerive & Berwick Zero Clearance Box and Flue Kit Part No Assembly Instructions
Regency Bellerive & Berwick Zero Clearance Box and Flue Kit Part No 946-762 Assembly Instructions Kit Contents 63 screws Base assembly LH Inner side panel RH Inner side panel Back Inner panel Top Inner
More informationA. Codes and Standards that are standard at the University. C. Coordinate cleanout locations with Architect.
PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
More informationCI/SfB Oct 12 (52.5) Uniclass L7314
CI/SfB Oct 12 (52.5) Uniclass L7314 Bailey Flow-therm Product Selector A RANGE OF QUALITY AND ROBUST RAINWATER OUTLET AND VENTILATION SYSTEMS FOR FLAT ROOFS, MANUFACTURED FROM RIGID POLYURETHANE. Bailey
More informationInstallation Instructions
Installation Instructions Flue Gas System Basic Kit HT-K - Horizontal Flue Gas System For GB125 Oil Condensing Boiler For trained and certified Installers Please read carefully prior to installation. 6
More informationInstallation Instructions
Installation Instructions Roof edge trim profile Series TA-4F multi-piece extruded aluminium profile front face height series TA-4F: 150-200 mm with patented 4F brackets height-adjustable, horizontally
More informationCI/SfB Oct 12 (52.5) Uniclass L7314
CI/SfB Oct 12 (52.5) Uniclass L7314 Bailey Flow-therm Product Selector A RANGE OF QUALITY AND ROBUST RAINWATER OUTLET AND VENTILATION SYSTEMS FOR FLAT ROOFS, MANUFACTURED FROM RIGID POLYURETHANE. Bailey
More informationGas Fireplaces. B41XTE-10 Gas Fireplace. Framing Dimensions: Unit Dimensions: Non-Combustible 1012mm Requirements: V Opening for gas connection
1XTE-1 Gas Fireplace Model 1XTE-NG1 1XTE-LP1 Fuel Type Natural Gas Propane Gas Minimum Supply Pressure Manifold Pressure - High Manifold Pressure - Low 5 W.C. (1.5 kpa) 3.5 W.C. (.7 kpa) 1. W.C. (. kpa)
More informationContemporary Collection
HZ5E Gas Fireplace Model HZE-NG HZ5E-LP Fuel Type Natural Gas Propane Gas Minimum Supply Pressure 5 W.C.(1.5 kpa) 1 W.C. (.9 kpa) Manifold Pressure - High 3.5 W.C. (.7 kpa) 1 W.C. (.9 kpa) Manifold Pressure
More informationDIRECT-TEMP SELKIRK DIRECT VENT SYSTEM
C I NT ER T EK Wa r noc k CM He r sey US U L LISTED CAUTION: WEAR GLOES WHILE HANDLING SHEET METAL PARTS TO AOID PERSONAL INJURY. SHARP EDGES OR PROJECTIONS CAN CUT YOU. Selkirk DIRECT-TEMP Direct ent
More informationBosch OptiFlow Professional Internal
Bosch OptiFlow Professional Internal Room-sealed continuous flow water heater and flue components. The OptiFlow Professional Internal offers: 3 6 Star efficiency 3 Room sealed appliance 3 Inbuilt temperature
More informationRosette Modular Scaffolding System
Rosette Modular Scaffolding System The rosette modular security scaffolding system to be used in facades, has been produced in accordance with the structural design conditions stated by the following applicable
More informationSECTION SECURITY GRILLES 670 SERIES UPCOILING SECURITY GRILLE
SECTION 08 33 00 SECURITY GRILLES 670 SERIES UPCOILING SECURITY GRILLE Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word click on round
More informationHOME SYSTEMS CONSTRUCTION PROCEDURE
HOME SYSTEMS WWW.QUICKBUILTHOMES.COM.AU CONSTRUCTION PROCEDURE INDEX - PARTS LIST PARTS LIST QBRC75(C) QBRM75C) QBSIPS75 QBRFSZ75C QBRFBC75C QBRF3030G QBRGSQC QBRFRC75C QBRFZEC QBRF4040C QBSACC75 QBFR7330WC
More informationSECTION PLUMBING EQUIPMENT AND SPECIALTIES
FULTON H3 PLUMBING EQ. AND SPECIALTIES 221114-1 SECTION 221114 PLUMBING EQUIPMENT AND SPECIALTIES 1.PART I - GENERAL 1. 01 All plumbing equipment included in this Specification shall be furnished and installed,
More information60/100 VERTICAL FLUE INSTRUCTION MANUAL FLUE KIT INSTALLATION ROOM SEALED FLUE
INSTRUTION MANUAL FLUE KIT 7 716 191 156 ROOM SEALED FLUE 60/100 VERTIAL FLUE FOR USE WITH WORESTER APPLIANES: Greenstar FS 30Di Regular, Greenstar FS 42Di Regular, Greenstar Highflow 440Di, Greenstar
More informationStudent Services & Classroom Addition. A. This Section includes the following sanitary drainage piping specialties:
SECTION 221319 - SANITARY WASTE PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following sanitary drainage piping specialties: 1. Cleanouts. 2. Floor drains. 3. Roof flashing
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey. A. This Section includes the following sanitary drainage piping specialties:
SECTION 221319 - SANITARY WASTE PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following sanitary drainage piping specialties: 1. Cleanouts. 2. Floor drains. 3. Roof flashing
More informationPowermax HE 85, 115 & 150 Litre Condensing Boilers with Integrated Hot Water Storage
Installation Instructions - Systems Powermax HE 85, 115 & 150 Litre Condensing Boilers with Integrated Hot Water Storage These instructions cover the installation of the following kits and their options:
More informationAssembly Instructions
QSM-BSB3 Railway Station Building - TEMPLETON Assembly Instructions MAIN PARTS DIAGRAM LAMP ROOM END WALL BUILDING FRONT PLATFORM SIDE STORE ROOM END WALL WAITING AREA REAR WALL INTERNAL WALL (x2) MAIN
More informationInstallation Instructions
InnoFlue Single Wall, Flex, Concentric Vent System The installation instructions should be kept with the appliance for maintenance. Examine all components for possible shipping damage prior to installation.
More informationMASPORT I5000 INSERT FIRE, AUSTRALIAN MODEL
MASPORT I5000 INSERT FIRE, AUSTRALIAN MODEL INSTALLATION INSTRUCTIONS Manufactured in New Zealand by: GLEN DIMPLEX AUSTRALASIA LIMITED PO Box 58-473 Botany Auckland 2163 Ph: 0800 666 2824 Fax: 09274 8472
More informationA. Codes and Standards that are Standards at the University. A. Provide floor drains in all toilet rooms, janitor closets, and mechanical rooms.
PART 1: GENERAL 1.01 Purpose A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
More informationChimney Lining Systems
R Chimney Lining Systems Gas or Propane Fired Appliances Table of Contents 1. General Instructions and Warnings U.L. and Manufacturers Specifi cations...2 2. Types of Liner Systems...3 3. FLEXJET Installation
More informationF Ü R D I E ZU K U N FT G E DAC HT. Flat roof vents. Soil vent pipes Refurbishment vents Cold roof vents
F Ü R D I E ZU K U N FT G E DAC HT. Flat roof vents 1 Soil vent pipes Refurbishment vents Cold roof vents F Ü R D I E ZU K U N FT G E DAC HT. alwitra waterproofing system Flat roof vents are part of the
More informationZ-Vent Model SVE Series III
Special Stainless Steel Venting System for Gas Burning Appliances Category I, II, III, & IV Tested and Listed By Underwriters Laboratories Inc. UL 1738 & BH636 Note the following before installation of
More informationHigh Performance Pumice Based Concrete Flue Linings
High Performance Pumice Based Concrete Flue Linings 7mm Pumice Based Flue Liners High performance pumice based concrete flue liners Red Bank s range of 7mm High Performance Pumice Based Concrete Liners
More informationSPECIFICATION FOR TUBULAR STEEL LIGHTING COLUMN. Reference is made in this Specification to the following:
SPECIFICATION FOR TUBULAR STEEL LIGHTING COLUMN 1. SCOPE This specification covers the design, fabrication and testing of tubular section, galvanised steel friction fit jointed street light columns of
More informationPo tterton Suprima HE Range>>
M ain supports The code of practice for the installation, commissioning & servicing of central heating systems. Po tterton Suprima HE Range>> The Suprima HE Range has an energy rating B on a scale of A
More informationRIGID SOLAR INSTALLATION MANUAL
RIGID SOLAR INSTALLATION MANUAL Sunlover Heating Factory 5, 9 Jersey Road Bayswater VIC 3153 T: 03 9720 2133 F: 03 9720 3266 New South Wales 2/20-22 Foundry Road Seven Hills, NSW 2147 T: 02 9838 0000 F:
More informationNU-WALL EXTRUDED ALUMINIUM CLADDING. Installation Specifications Vertical orientation (over cavity)
September 2014 NU-WALL EXTRUDED ALUMINIUM CLADDING Installation Specifications Vertical orientation (over cavity) 1. NW-V001C; Cavity batten layout 2. NW-V002C; Battening options 3. NW-V002C; Battening
More informationSECTION PLUMBING PIPING SYSTEMS
SECTION 15300 PLUMBING PIPING SYSTEMS PART 1 - GENERAL 1.01 SPECIAL NOTICE A. Each contractor shall read all relevant documents, become familiar with the job, the scope of work, type of general construction,
More informationO B R O U N D G R E A S E D U C T
TM O B R O U N D G R E A S E D U C T SlimVent OBROUND GREASE DUCT SlimVent is a UL Classified zero-clearance grease duct system with the space saving profile of a field fabricated rectangular product.
More informationDunbrik Mini Clearflow Gas Flue Block System
Dunbrik Mini Clearflow Gas Flue Block System System Guide for traditional and timber frame domestic dwellings Certificate No.FM24104 Dunbrik Mini Clearflow Gas Flue Block System General system details
More informationBUILD A SHOWER CUBICLE
BUILD A SHOWER CUBICLE Building a shower cubicle requires some experience in carpentry and tiling. You also need a degree of expertise in wiring and plumbing in order to install a shower unit. By all means
More informationEcoteck Amalfi Freestanding. Wood Pellet Burning Heater
coteck Amalfi reestanding Wood Pellet urning Heater c o t e c k A m a l fi r e e s t a n d i n g Wood Pellet urning Heater Installation Specifications Safety testing of the coteck Amalfi reestanding Wood
More informationPipe Flashing Systems
Uniclass L52944:P71 EPIC E375:X71 CI/SfB (47) In6 Pipe Flashing Systems Pipe Flashing Systems The widest range of pipe flashings available to the market Contents Page Front Cover 1 Contents 2 Introduction
More informationSI T T FSS/FSTT Open Fire
SI 440-600-700-700T-780-780T-900-1100 FSS/FSTT Open Fire Freestanding Solid Fuel Burner - Indoor Open Wood Fire Available in Square Top or Taper Top Options Installation Instructions Note: Flue System
More informationSECTION CONDUITS AND BACKBOXES FOR COMMUNICATIONS SYSTEMS
SECTION 16711-27 05 28.33 PART 1 - GENERAL 1.01 SUMMARY A. This section includes Labor, materials and equipment necessary to complete the installation required for the items specified under this Section,
More informationDuraFlex. Flexible stainless steel relining for masonry chimney. UL 1777 and ULC S635.
DuraFlex Flexible stainless steel relining for masonry chimney. UL 1777 and ULC S635. Specifications DuraFlex Pro Applications DuraFlex Pro ultra flexible relining for masonry chimney. Use with gas, wood
More informationModel: 31ST-ACC-AU. Model: 31M-ACC-AU
QUADRA-FIRE 3100 SERIES ACC WOOD BURNER INSTALLATION INSTRUCTIONS Model: 31ST-ACC-AU Model: 31M-ACC-AU INSTALLATIONS TO COMPLY WITH AS/NZS2918:2001 AND WILL REQUIRE A BUILDING CONSENT IMPORTANT: Read all
More informationFor over 75 years, Main has manufactured domestic gas appliances designed to make life more affordable and comfortable for as many people as possible.
MAIN HE RANGE For over 75 years, Main has manufactured domestic gas appliances designed to make life more affordable and comfortable for as many people as possible. Today, Main is part of one of Europe
More informationUniversity of Delaware
University Contact: Energy & Engineering Group (302) 831-1744 SECTION 22 13 00 _SANITARY SEWER PIPING SYSTEMS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Sanitary sewer piping buried 2. Sanitary
More information