DML-Series. Pelton wheel flow meter

Transcription

1 DML-Series Pelton wheel flow meter

2 Flow meter manufacture As a specialist in flow measurement technology, TrigasDM supplies high-quality measuring instruments, electronics and calibrators for liquids and gases. Made in Germany Our products are exclusively developed and manufactured in Neufahrn, 20 km north of Munich, ensuring world-class technical knowhow for our customers. Contact We are proud of our high-quality products and friendly customer service and welcome you as a valued customer to our growing family. You can benefit from our long-standing experience and our comprehensive technical support. TrigasDM GmbH Tel.: Erdinger Str. 2b Fax: info@trigasdm.com Neufahrn, Germany TrigasDM GmbH - June

3 Technical data Flow range: Response time: see "Measuring ranges" table <4 ms Temperature range: -50 C to +150 C Operating pressure: Viscosity: up to 400 bar, Depending on connection, optionally also higher pressures possible Each turbine is calibrated according to customer specifications and delivered with individual calibration protocols. (Standard viscosity: 1.3 mm²/s) Liquid Calibration accuracy: Repeatability: Accuracy: Linearity: ±0,05% of measured value ±0,01% of measured value ±0,25% of measured value in the linear flow range ±0.1% of the measured value in the linear flow range Gas Calibration accuracy: Repeatability: Accuracy: Linearity: ±0, 3% of measured value ±0,2% of measured value ±0,60% of measured value in the linear flow range ±0,1% of the measured value in the linear flow range Standard material: Stainless steel TrigasDM GmbH - June

4 Measuring ranges a) Gas Linear Extended max. Range Flowrange K-Faktor 1) Frequenz 1) [ml/min] [ml/min] Model min. max. min. max. [Pulse/ml] [Hz] DML , DML , DML , DML , DML , , ) The K-factors and frequency data are average values. Each turbine is calibrated according to customer specifications and delivered with individual calibration protocols. b) Liquid Linear Extended max. K-Faktor 1) Range Flowrange Frequenz 1) [ml/min] [ml/min] Model min. max. min. max. [Pulse/ml] [Hz] DML 0.6 7,57 75,7 3, DML , DML , DML , DML , ) The K-factors and frequency data are average values. Each turbine is calibrated according to customer specifications and delivered with individual calibration protocols. TrigasDM GmbH - June

5 Dimensions, Align while installing align Model InnerØ DML0.6 0,6 DML1.0 1,0 DML2.0 2,0 DML4.0 4,0 DML5.0 5,0 length A Housing height/depth B 1) Measuring sensor (pickoff) Screw in depth Thread Type 76,2 SW 36* 17,7 5/8-18UNF-2B 1) The total height is calculated from the height (B) of the flow meter plus measuring element minus the screw-in depth. *) AF = Width across flats TrigasDM GmbH - June

6 End Fitting types and operating pressure Female threads (GF) Model DML0.6 - DML5.0 A B [Zoll] 76,2 G1/2 (20,955mm) C max. operating pressure [bar] 0,6 400 NOTE Other end fittings can be supplied on request TrigasDM GmbH - June

7 Piping Configuration Turbine flow meters can be affected by the velocity profile of the fluid being measured. Installation with proper pipe runs will reduce or completely eliminate flow profile induced measurement errors during calibration and operation. Inlet section and outlet section, schematic diagram A straight run of pipe of at least 10 times the pipe diameter in an upstream direction, and 5 times the pipe diameter in a downstream direction are recommended (see figure and table). The upstream section should be fitted with flow straightening vane. Appropriate flow straightening sets (up- and downstream) are available on request. Contamination / filter All pipe sections and components in the metering line must be cleaned prior to the installation of the flow meter. Pipe Sealants, metal shavings and slag can damage the flow meter. If the cleanliness of the fluid cannot be guaranteed, a filter should be installed upstream of the flow meter, subject to the diameter of the flow meter. The selection of the filter depends on the precision opening of the flow meter and the bearing of the rotor. Contamination between the inside of the housing and Pelton wheel can lead to a blockage of the flow. A filter must always be used for gas measurements Model InnerØ Filter mesh size for Jewels Pivot bearing Filter mesh size for Ball bearings DML0.6-0,6 min.100 Mikrometer min.10 Mikrometer DML5.0 TrigasDM GmbH - June

8 Explosion protection (ATEX) All DM-Series turbine flow meters are available in intrinsically safe design. The design consists of the turbine flow meter and the ATEX Pickoff. The following type of protection applies to this construction: - Flow Sensor ATEX: II 1G Ex ia IIC (Zone 0,1,2) - Temperature Sensor ATEX: EX II 2G Ex ib IIC T4 Gb (Zone 1,2) The turbine flow meter is installed in the hazardous area. The mounting of the barrier and the TriLIN is carried out in the safe area. Without barriers, the turbine flow meter must not be operated in the hazardous area. Cable lengths of up to 400 m are possible depending on the safety barrier used. TrigasDM GmbH - June

9 Model Numbering key DML - Serie (z.b. DML-0.6GF-BA-1) DML -0.6 GF -BA -1 Pickoff (f.e. L02 L5 T) L 02 L5 T Construction Material - 1 stainless steel Bearing -BA = Ball bearings, standard -BC = Ball bearings, ceramic -JP = Jewel Pivot Bearing -BA = Ball Bearing End Fitting AN = threaded connection HS = hose connection GF = ½ G Female threads Temperature Sensor T = Integrated in Pickoff 0 = without Connector C2 = MS Connector 2 Pins C3 = MS Connector 3 Pins C4 = MS Connector 4 Pins L1 = 1m cable outlet L3 = 3m cable outlet L5 = 5m cable outlet Thread 01 = 5/8-16, High Profile 02 = 5/8-16, Low Profile 03 = 5/8-16, High Profile, Explosion Proof 04 = 5/8-16, High Profile, High Temp. 06 = 11/16-24, High Profile 07 = 11/16-24, Low Profile 08 = 11/16-24, High Profile, Explosion Proof 09 = 11/16-24, High Profile, High Temp. Base Model Model R = Frequenzmoduliert (RF) M = Magnetisch (Mag) L = Lysis SMART-RF Product Name TrigasDM GmbH - June