Blender. Instruction Manual

Transcription

1 Blender Model BL-020B Instruction Manual Version Pepper Mill Court, Mississauga, ON, L5L 4X Witmer Industrial Estates, Unit 4, Niagara Falls, NY,

2 Table of Contents Model BL-020B Section General Information Safety and Warranty Page Technical Specifications Operation Parts Breakdowns Electrical Schematics Warranty Registration

3 General Information Omcan Manufacturing and Distributing Company Inc. and Food Machinery Of America, Inc. dba Omcan are not responsible for any harm or injury caused due to any person s improper or negligent use of this equipment. The product shall only be operated by someone over the age of 18, of sound mind, and not under the influence of any drugs or alcohol, who has been trained in the correct operation of this machine, and is wearing authorized, proper safety clothing. Any modification to the machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of the machine while in operation. Important Safeguards Safety and Warranty 1. Read all instructions. 2. To protect against risk of electrical shock, do not put motor base in water or other liquid. 3. Close adult supervision is necessary when the appliance is used by or near children. 4. Unplug the power cord from the wall outlet when the machine is not in use. Unplug before assembling or disassembling parts, and before cleaning other than washing the container. 5. Never touch or make contact with moving parts. 6. Do not operate any appliance with a damaged cord or plug; or after the appliance malfunctions; or is dropped or damaged in any manner. Call Omcan at once for possible replacement, examination, and repair, electrical or mechanical adjustment. 7. Do not use outdoors. 8. Do not let the power cord hang over edge of table or counter, or touch hot surfaces. 9. Keep hands and utensils out of the container while motor is running to prevent the possibility of severe personal injury and/or damage to the blender. A rubber scraper may be used, but only when the blender is not in use. 10. CAUTION: Blade is sharp. Handle carefully. Never try to remove blade while container is sitting on the motor base. Do not operate with loose or damaged blades. To reduce the risk of personal injury, never place blade assembly on motor base without the blender container properly attached. 11. Always operate with the lid in place. 12. Display window area will scratch when contacted with a scouring pad or sharp object. Use a soft cloth to wipe the control panel area clean. 3

4 Technical Specifications Features This blender was developed based on years of experience and technology. The powerful motor with stainless steel blades are designed for blending various foods. The Industrial high-speed motor can reach a maximum speed of 29,000 rpm. The thermally protected motor is Fan cooled. The speed control is designed to provide a steady current, while protecting the motor. Over current protection system. Durable Stainless steel driven connector. Blades group is geared by ball bearings. Built with special durable materials and waterproof adhesive. Voltage Capacity Endurance of Container Power Weight Operation 110V-120V /60Hz 2000c.c -40 C~180 C 1300W 5.5kgs Length of Cord 1.8M Dimension Protector *110V-120V machine is available in 15A plug. Fruit Smoothies 200 x 230 x 490mm Current protector, Thermal protector for motor 1. Ingredients: Ice, Fruits, Water. 2. Put the material into the container; cover with the lid; when making thick drinks, please insert the blending stick. 3. Set the variable button to the lowest speed, then turn on, gradually increasing to the highest speed. 4. Turn on the unit; if water is limited, please use the blending stick. 5. After 3-5 seconds, when the blending sound suddenly diminishes, the ingredients have been blended enough. Over blending will turn the ice into water. Blending Fruit & Vegetable 1. Put fruit or vegetables and a little water into the container. 2. Set the variable button to the lowest speed, then turn on, gradually increasing to the highest speed. 3. Turn on the unit; after 4-6 seconds of blending, the ingredients should roll smoothly. Do not over blend. 4

5 Operation Note: 1. Pulse switch is mainly used for testing or blending special materials do not use it frequently. 2. Do not run for more than 2 minutes when blending dry materials. Control Panel Mechanical Control Panel ON/OFF Switch Up for ON; Down for OFF. HIGH/LOW Pulse Switch Up for High speed at 29000rpm; Down for Low speed at 16000rpm. Pulse button can only be used when the power switch is ON, The PULSE switch can be used to quickly refresh product in the container by depressing the switch and holding down as long as needed. Variable Speed Dial It allows the user to select continuous variable speeds ranging from 16000rpm to 29000rpm. The PULSE switch overrides the variable speed dial. Remark: 1. On all units the built-in thermal sensor keeps track of how hot the motor gets and will automatically shut down the motor if it is overheating. User should remove the container and wait until the machine cools down. This takes about 2 minutes. 2. Special Note: Please check your operation when the motor is overheated. If the machine runs all day or the material is too thick, it can easily overheat. 5

6 Parts Breakdown Model BL-020B

7 Parts Breakdown Model BL-020B Description Position Description Position Description Position Fill Cap 1 Stainless Steel Pad 11 Circuit Board 21 Jug Lid 2 Rubber Pad 12 Safety Switch 22 Plastic Jug 3 ABS Top Cover 13 Safety Switch Fitting 23 Blades Group 4 On/Off Switch 14 Motor 24 Blades Sealing 5 Power Switch 15 Fuse 25 Jug Sealing 6 Pulse Switch 16 Base 26 Stainless Steel Nut 7 Speed Knob 17 Anti-Slip Rubber Feet 27 Aluminum Positioning Pin 8 Safety Switch Transmitter 18 Air Outlet Panel 28 Clutch 9 Spring 19 Power Cable & Plug 29 Motor Positioning Screw 10 Shock Proof Ring 20 7

8 Electrical Schematics Model BL-020B

9 Warranty Registration Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at the perforation and then send to the address specified below. You can also register online by visiting: For mailing in Canada OMCAN INC. PRODUCT WARRANTY REGISTRATION 3115 Pepper Mill Court, Mississauga, Ontario Canada, L5L 4X5 For mailing in the US OMCAN PRODUCT WARRANTY REGISTRATION 4450 Witmer Industrial Estates, Unit 4, Niagara Falls, New York USA, Purchaser s Information Name: Company Name: Address: Telephone: City: Province or State: Postal or Zip: Address: Country: Type of Company: Restaurant Bakery Deli Dealer from which Purchased: Butcher Supermarket Caterer Dealer City: Dealer Province or State: Institution (specify): Invoice: Other (specify): Model Name: Model Number: Serial Number: Machine Description: Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY): Thank you for choosing Omcan 9

10

11

12 Over the last 60 years, Omcan has grown to become a leading supplier to the food service industry in Canada and the USA. Our success over these many years is directly attributed to our established relationships with all of our valued customers and through providing them with Diverse, Dependable and Proven products. Omcan continues to help our customers remain competitive. With associates in North America, Europe, Asia, and South America, our global footprint continues to expand as we hold to the principle that clients benefit from the accessibility and familiarity of our sales team. In 2013 as our geography and brand recognition continued to grow, we changed to one name Omcan Food Machinery. In over 200,000 sq ft of warehouse space we stock over 2,500 quality food equipment and supplies for the food preparation market.