Ref: 132. Cable Management System. Catalogue Ref: 132

Transcription

1 Ref: 132 Cable Management System Catalogue Ref: 132

2 For the calculation and selection of Wire Mesh Tray pemsapro is the brand new software developed by emsa for the calculation and selection of Wire Mesh Tray, Steel Cable Tray and Channel Systems. This program allows the user to enter and define all parameters of the installation, and produces a choice of the most suitable trays, along with the required accessories, brackets, clamps, etc, in order to correctly configure a specific electrical installation. The cable type can also be chosen, thanks to the extensive data base of the main cable manufacturers. pemsa pro provides an easy and intuitive process, via a complete set of on-screen menus, that allows the user to enter all features of the installation. The software has two modes: Quick Calculation and Installation Calculation. The latter allows the breakdown of the project into floors, areas, sections and sub-sections in order to obtain a detailed definition of the installation. pemsapro contains a vast collection of 3 tray assemblies, and a powerful tool for visualising these graphics. The views can be exported and inserted into any report or technical document. Last but not least, the software produces a complete report with all of the technical data and prices of the individual components required for the installation. Metal tray and channel system for

3 Innovations. New Omega bracket 2 Innovations. New range of reinforced supports 3 Innovations. New range of accessories pemsaband 4 dvantages. rejiband RoHS BYCRO 5 dvantages. Fire resistance. E90 7 dvantages. UL Classified 7 Solutions 8 rejiband 9 rejiband false floor 17 rejitech 18 supports&structures 19 pemsaband System 28 inducanal 38 Range Overview. Flexible Conduit System 40 Surface treatment to prevent corrosion 41 Recommendations for the correct installation of cable trays 42 rejiband maximum safe working load 45 Examples of assembly 46 Fire resistance. E90 48 Electrical continuity 50 Earthing 51 Electromagnetic Compatibility (CEM) 52 Index by products 54 cable support and management.

4 TENTO OME BRCKET UNIVERSL Single support for all trays on the market T T E ISTINCT VNTES Compatible with all trays on the market: rejiband, metal and VC. 50% reduction in number of references. Compatibility with other systems. Savings in investment in stock. Savings in storage space. Better service and lower stock. Quick and easy installation. Only 2 steps. 1. lace the tray into the slots 2. Bend the clips up with a tool. Can also be installed with joints or "screws". New strengthened profile system with Omega extra click. Increase mechanical performance by 20%. llows support of the rods in the reinforced rib, improving stability and installation of the tray. VERY IMORTNT, the trays will not release from the bracket. Reinforcing rib and pan support rod Traditional profile section. 2

5 TENTO TENTO TENTO SUORTS New range of Reinforced Supports SINLE SUORT Compatible with all tray types. e.g. Wire Mesh Tray, Metal Tray, VC, etc. T T E VNTES Unified range for both rejiband and pemsaband trays. Logistic savings. Reduced reference numbers. T T E Reinforced Strength The bracket has been designed with curves for greater strength and load bearing capacity. Click System Fixing pin for quickly securing the tray thus avoiding movement in any direction. T T E Lateral rooves Increases the load resistance of the bracket and reinforces the area supporting the tray. etail of fixing Click System Side ressing Fully embossed side enhances the strength of the bracket and improves it s load capacity. Back ressing Embossed back increases the resistance of the bracket and prevents any bending. etail of fixing with pemsaband 3

6 New Range of ccessories pemsaband T T Functionality and Speed of ssembly 90º Bend, Crossover, Tee, Side Entry, with their corresponding covers. New arts, Inside and Outside Risers. Full range in all heights, 35, 60 and 85. Finishes and H... 90º Bend 300, height 60 Crossover 400, height 85 Click System Joint. There is no need to use joints to connect the accessories to the straight sections of pemsaband. ccessory Covers overlap on the tray, improving stiffness and tightness of the assembly. N20 precut conduit exits. In heights 60 and 85 for the installation of fittings or glands of M20, 11 or 13. Inside Riser 4 4

7 rejiband Wire Mesh Tray Corrosion (White) BYCRO Wire Mesh rejiband Featuring: - Enhanced rotection against Corrosion - Safety Edge - Chrome-VI free HOURS E E.B./BYCRO Laboratory Tests performed under STM B117 Standard proves the excellent behaviour of emsa BYCRO finish against corrosion. - Compliant with RoHS 2002/95/CE and WEEE 2002/96/CE cod. CYNW. E

8 The rejiband BYCRO tray from EMS respects the environment and meets the RoHS standard. emsa has made a series of improvements to its rejiband tray and its Bycro finish now offers the following advantages and features: emsa leads the market with its bichromed electro-galvanised rejiband tray. Using the latest generation processes and products, the Bycro finish is fully compliant with the current RoHS legislation and REE directives. emsa is committed to protecting the environment by eliminating hexavalent chromium in its electro-galvanising plants. Its rejiband trays are manufactured without products that are harmful, contaminating or have an adverse effect on the environment. The BYCRO finish still offers superb anti-corrosion protection. The BYCRO finish has a unique iridescent gold finish and superb technical properties. The reference and coding systems for the product remain the same. emsa continues to lead the way with its rejiband BYCRO tray which incorporates superior anti-corrosion properties but is free of hexavalent chromium (Cr VI) and other heavy metals in compliance with 2002/95/CE RoHS. emsa continues to offer its customers a tray which guarantees greater safety, a better finish and an optimum price/quality ratio while protecting our environment. rejiband BYCRO FLNE 35 xb 100x x x x x rejiband BYCRO FLNE 60 xb 060x x x x x x x x x rejiband BYCRO FLNE 100 xb 200x x x x x

9 Fire Resistance rejiband basket tray has successfully exceeded the fire resistance tests defined by the erman Standard IN Fire behaviour of building materials and elements, Fire resistance of electric cable systems required to maintain circuit integrity, by withstanding 1000 ºC (1832ºF) temperature during 90 minutes, thus obtaining the E90 certification. In case of fire, rejiband basket tray does not harm either the people or the installation itself (no fumes of toxic, corrosive or opaque nature at all), and ensures enough structural resistance and the power supply to the most critical systems (emergency lighting, fire detection, etc). For further information, consult pages 48 and 49. UL Classified rejiband ELECTRICL CONTINUITY URNTEE. This certification ensures, when using rejiband basket, that the correct electrical continuity between trays exists which could, under certain circumstances, be used as a protective earth without using any additional protective conductor. ny protective conductor would connect all earthed points of an installation to the earth conductor, in order to eliminate the risks through indirect contact. The UL Classified mark, achieved by EMS, is the result of testing electrogalvanized rejiband basket trays (35, 60 & 100mm flange) joined with the Reinforced Joint Clamp. It certifies that the requirements of the NEM VE Metal Cable Tray Systems standards are met in accordance with the Canadian Electrical Code and the National Electrical Code, NEC. The value of the UL CLSSIFIE marking UL is one of the most renowned safety certification institutions worldwide. UL marked product is an item that has been successfully tested by the UL in accordance with certain safety requirements. These tests ensure the use of this product does not bring any significant risk of fire, electric shock or any other linked danger. The safety requirements are equally met in the long term, since UL performs periodic checks and verifications at the manufacturer s premises. 7

10 EMS EMS EMS EMS REJIBN REJIBN REJIBN EMS EMS Under floor solution REJIBN REJIBN EMS EMS REJIBN REJIBN EMS EMS REJIBN REJIBN FLOOR FOOT REJIBN REJIBN EMS EMS ress fit REJIBN REJIBN Clean and tidy electrical installation. Quick and easy assembly. Material and Time Savings by using the floor foot. Can be used with all sizes of rejiband. For the optimum maintenance, EMS recommends a minimum distance of 40mm between the rack and the floor. If the rack crosses pipes, the rack must always remain above the pipes. rejitech false ceiling solution rejitech fastener click Quick installation. No joints, no accessories - just the rejitech FSTENER. Easy and quick assembly. Cables are inserted from the side. Installation can be carried out by just one person. Tidy cabling. Maximum ventilation. Easy upgrade or modification of the cabling. 60mm high, ideal for small places. 60 CEILIN FSTENER & CBLES INSERTE FROM THE SIE 8

11 TENTO 030/ TENTO 030/ rejiband T T E Length 3000 mm xb iameter sale ack Rod (mm) (length) Unit. 100x m 8 200x m 6 300x m 6 400x m 4 S.S. 304 xb iameter sale ack Rod (mm) (length) Unit. 100x m 8 200x m 6 300x m 6 400x m 4 BYCRO xb iameter sale ack Rod (mm) (length) Unit. 100x m 8 150x m 8 200x m 6 300x m 6 400x m 4 S.S. 316 xb iameter sale ack Rod (mm) (length) Unit. 100x m 8 200x m 6 300x m 6 400x m 4 rejiband T T E For Rejiband 60x60, please use Side Support 60, See page 16 BYCRO xb iameter sale ack Rod (mm) (length) Unit. 060x m 8 100x m 8 150x m 8 200x m 6 300x m 4 400x m 2 450x m 2 500x m 2 600x m 2 xb iameter sale ack Rod (mm) (length) Unit. 060x m 8 100x m 8 150x m 8 200x m 6 300x m 4 400x m 2 500x m 2 600x m 2 S.S. 304 xb iameter sale ack Rod (mm) (length) Unit. 060x m 8 100x m 8 150x m 8 200x m 6 300x m 4 400x m 2 500x m 2 600x m 2 Length 3000 mm S.S. 316 xb iameter sale ack Rod (mm) (length) Unit. 060x m 8 100x m 8 150x m 8 200x m 6 300x m 4 400x m 2 500x m 2 600x m 2 (*) The hot dip galvanized finish is NOT N CCURTE ESTHETIC FINISH. It is a very effective corrosion protection. COLOUR IFFERENCES CN OCCUR (shades of grey), brightness and surface finish (roughness, smoothness), created during the process employed. This is normal and does NOT FFECT THE QULITY N URTION OF THE NTI-CORROSION ROTECTION. 9

12 TENTO 030/ TENTO rejiband 100 rejitech (false-ceiling tray) T T E T T E Length 2000 mm (age 18) Length 3000 mm xb Finish sale (length) ack Unit. 100x BYCRO 2 m 8 BYCRO xb iameter sale ack Rod (mm) (length) Unit. 200x m 2 300x m 2 400x m 2 500x m 2 600x m 2 xb iameter sale ack Rod (mm) (length) Unit. 200x m 2 300x m 2 400x m 2 500x m 2 600x m 2 S.S. 304 xb iameter sale ack Rod (mm) (length) Unit. 200x m 2 300x m 2 400x m 2 500x m 2 600x m 2 S.S. 316 xb iameter sale ack Rod (mm) (length) Unit. 200x m 2 300x m 2 400x m 2 500x m 2 600x m 2 ngle tray 2001 Bolt cutters asymmetrical-cut Length 3000 mm Mount with ngle tray fastener (age 13) xb Finish sale (length) ack Unit. 109x BYCRO 3 m 6 109x m 6 109x S.S m 6 109x S.S m 6 sale Each BYCRO Electrolytic Bichromate BS-EN H... Hot-dip galvanised BS-EN-ISO 1461 E.B. Electrolytic Bichromate BS-EN S.S. assivated stainless steel ISI 304 or ISI 316 re-galvanised BS-EN E.. Electrogalvanised BS-EN 12329, available on request 10

13 TENTO TENTO Fast click joint NEW T T Finish sale BYCRO ack of ack of 50 Quick Fitting No bolts No special tools Electrical continuity guaranteed Suitable for use with all widths of Rejiband in 60 and 100 depths only. Fast click base joint T T NEW Quick Fitting No bolts No special tools Electrical continuity guaranteed Suitable for use with all widths from 100 upwards. Finish sale BYCRO ack of ack of 10 Light duty wall support NEW ESY INSTLL. Suitable for 35 and 60 flange. 100 and 150 wide. T T E Finish sale BYCRO ack of ack of 25 Light duty ceiling support NEW ESY INSTLL. Suitable for 35 and 60 flange. 60, 100 and 150 wide. T T E Finish sale BYCRO ack of ack of 36 (*) The hot dip galvanized finish is NOT N CCURTE ESTHETIC FINISH. It is a very effective corrosion protection. COLOUR IFFERENCES CN OCCUR (shades of grey), brightness and surface finish (roughness, smoothness), created during the process employed. This is normal and does NOT FFECT THE QULITY N URTION OF THE NTI-CORROSION ROTECTION. 11

14 Luminaire and box support NEW T T Finish sale BYCRO ack of ack of 8 ESY INSTLL. Suitable for 35 and 60 flange heights, and all widths except for 60 and 150. E90 connector NEW E90 connector NEW T T T T ccessory designed to create an E90 assembly when using RLUS Brackets. Further information on request. ccessory designed to create an E90 assembly when using SLUS Brackets. Further information on request. Finish sale ack of 15 Finish sale ack of 60 Channel click joint NEW T T Finish sale INOX ack of 100 Compatible with all of the leading brands of Channel. Can be used with all sizes of Rejiband except 60x60. rejiband pemsaband joint NEW 3301 T T Finish sale Each (**) Each (**) (**) Each package contains two parts, one for each flange. Special joint for coupling rejiband directly to pemsaband. BYCRO Electrolytic Bichromate BS-EN H... Hot-dip galvanised BS-EN-ISO 1461 E.B. Electrolytic Bichromate BS-EN S.S. assivated stainless steel ISI 304 or ISI 316 re-galvanised BS-EN E.. Electrogalvanised BS-EN 12329, available on request 12

15 TENTO TENTO TENTO Reinforced joint clamp T T E JUST 3 RTS! Captive bolt Simplifies assembly 20% improvement in mechanical performance Finish sale E.B. ack of ack of S.S. 316 ack of 50 CONNECTORS NEEE EVERY 3 METRES WIE Click connector T T E REJIBN SECURITY F S T E R Finish sale E.B. ack of ack of 25 CONNECTORS NEEE EVERY 3 METRES WIE S F E T Y Quick fitting No bolts No special tools. Just bend tabs with a screwdriver. Electrical continuity guaranteed Earth terminal for rejiband New design More economical Less weight Smaller pack size. In bags of 20 units Suitable for cable sizes mm 2 Material sale Brass ack of 20 art clamp T T E Finish sale E.B. ack of ack of S.S. 316 ack of 50 ngle tray fastener Use with hexagonal cone point screw M10x (not included) 20 E.B. sale ack of 10 Side joint-plate Splice plate Finish sale E.B. ack of ack of S.S. 316 ack of 50 Finish sale E.B. ack of ack of S.S. 316 ack of 10 Connector plate Wire end cap Finish sale E.B. ack of ack of S.S. 316 ack of 50 Material sale LSTIC ack of 100 (*) The hot dip galvanized finish is NOT N CCURTE ESTHETIC FINISH. It is a very effective corrosion protection. COLOUR IFFERENCES CN OCCUR (shades of grey), brightness and surface finish (roughness, smoothness), created during the process employed. This is normal and does NOT FFECT THE QULITY N URTION OF THE NTI-CORROSION ROTECTION. 13

16 TENTO TENTO ivider, Click type T T E 3m length sale (length) ack Unit m m m 12 sale (length) ack Unit m m m 12 S.S. 316 sale (length) ack Unit m m m 12 Faster Installation The finish on the 25, 50 and 80 flange comes packaged for correct storage. Identification Label Material sale LSTIC ack of 50 T T E BYCRO Electrolytic Bichromate BS-EN H... Hot-dip galvanised BS-EN-ISO 1461 E.B. Electrolytic Bichromate BS-EN S.S. assivated stainless steel ISI 304 or ISI 316 re-galvanised BS-EN E.. Electrogalvanised BS-EN 12329, available on request 14

17 TENTO TENTO Click central suspension Only 1 part with 2 nuts! T T E Cannot be used with Rejiband 60x60. M6 M8 M10 6.2x x x15.5 E.B. sale M ack of 20 M ack of 20 M ack of 20 sale M ack of 20 M ack of 20 M ack of 20 S.S. 316 sale M ack of 20 M ack of 20 M ack of 20 Threaded rod M6/M8/M10 Expanded range E.B. kg x B sale 202 M6x Each 202 M6x Each 407 M8x Each 407 M8x Each 509 M10x Each E.. kg x B sale 202 M6x Each 202 M6x Each S.S. 316 kg x B sale 202 M6x Each 407 M8x Each 407 M8x Each 509 M10x Each rejiband box support ø7 Fixing support for rejiband ø7x13 Suitable for voice, data and fibre optic installations T T E Material sale ress Fit Rejifix LSTIC ack of 20 (See page 17) Material sale LSTIC ack of 20 It is very economical. The support is pressed on. Without the need for any other accessory. It allows no electrical conductivity between the box and the tray. It is very economical and reusable. The support allows for adjacent installation. It requires no bolts or other fastenings for installation. Manufactured from a fire retardant plastic material. (*) The hot dip galvanized finish is NOT N CCURTE ESTHETIC FINISH. It is a very effective corrosion protection. COLOUR IFFERENCES CN OCCUR (shades of grey), brightness and surface finish (roughness, smoothness), created during the process employed. This is normal and does NOT FFECT THE QULITY N URTION OF THE NTI-CORROSION ROTECTION. 15

18 TENTO TENTO Central hanging plate 9 and 11 M8 = ø 9x16 M10 = ø11x18 CNNOT be used with Rejiband 60x60 E.B. Universal bracket Type sale 9 M ack of M ack of 20 9 M ack of M ack of 20 S.S. 316 Side support 60 T T E 9 M ack of M ack of 20 Essential for 60x60 wire mesh tray Finish sale E.B. Each Each S.S. 316 Each For installing boxes, use M5 bolts. Finish sale Each Each S.S. 316 Each Cover land bracket Click fit for fast fixing to tray. oes not require any additional nuts, bolts or clips m m m m m m m m 2 S.S m m m m m m m m 2 ress Fit For conduit size: M20 13 M20 16 M25 21 Finish sale E.B. Each 3m length sale (length) ack Unit m m m m m m m m 2 Mini universal bracket ata outlet T T E For installing boxes, use M5 bolts. Finish sale Each Each S.S. 316 Each Identification plate No text - for marking by the user Material sale LSTIC ack of 50 Zinc paint spray Finish sale LSTIC Each Contents: 400 ml. ress Fit sale Each BYCRO Electrolytic Bichromate BS-EN H... Hot-dip galvanised BS-EN-ISO 1461 E.B. Electrolytic Bichromate BS-EN S.S. assivated stainless steel ISI 304 or ISI 316 re-galvanised BS-EN E.. Electrogalvanised BS-EN 12329, available on request 16

19 EMS EMS TENTO EMS EMS EMS EMS EMS EMS EMS EMS EMS EMS EMS EMS EMS EMS EMS EMS rejiband false floor REJIBN REJIBN REJIBN REJIBN EMS REJIBN REJIBN REJIBN REJIBN EMS REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN Floor foot (reinforced) T T E Quick, easy installation For proper maintenance, the rack should be at least 40 mm away from the floor. If the rack crosses pipes, the rack must always be above the pipes. ress Fit rejiband ensures the highest cleaning and ventilation levels. REJIBN REJIBN REJIBN REJIBN ress Fit EMS EMS land bracket Material sale LSTIC Each ress Fit For conduit size: M20 13 M20 16 M25 21 Rejifix Selfsticking self-adhesive for data, cables and telecommunications. oes not damage the cables. Re-usable. REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN REJIBN Finish sale E.B. Each Earth terminal Suitable for cable sizes mm 2 Material sale Brass ack of 20 Colour Wide sale (length) BLCK 10 mm 25 m Roll dhesive & Hardener Comprises adhesive + hardener Contents: enough for approx. 100 feet sale Each (*) The hot dip galvanized finish is NOT N CCURTE ESTHETIC FINISH. It is a very effective corrosion protection. COLOUR IFFERENCES CN OCCUR (shades of grey), brightness and surface finish (roughness, smoothness), created during the process employed. This is normal and does NOT FFECT THE QULITY N URTION OF THE NTI-CORROSION ROTECTION. 17

20 TENTO TENTO rejitech ssembly in false ceiling T T E Quick installation. The assembly work can be carried out by just one person. Tidy cabling. Easy to modify. Minimum height. Cables can be inserted from the side. Maximum ventilation. rejitech Space needed (for the same number of cables) VC CONUITS Length: 1m. for same cable capacity Cables inserted from the side 2001 Finish sale (length) ack Unit E.B. 2 m 8 Ceiling fastener (ress Fit) Box support for rejitech T T E Mount to boxes with M6 screws. Finish sale E.B. ack of 25 Only for rejitech Finish sale E.B. Each BYCRO Electrolytic Bichromate BS-EN H... Hot-dip galvanised BS-EN-ISO 1461 E.B. Electrolytic Bichromate BS-EN S.S. assivated stainless steel ISI 304 or ISI 316 re-galvanised BS-EN E.. Electrogalvanised BS-EN 12329, available on request 18

21 TENTO TENTO Omega bracket universal T T E NEW NEW CLICK SYSTEM giving an easy and quick installation for LL of the trays on the market. Wire Mesh and Sheet Steel. NEW REINFORCE ROFILE increases the load capacity and the fitting of the tray. The supports can be easily stacked, thanks to the new profile and protector plug, therefore assisting in storage and logistics. Includes an Omega lug (pre-assembled) and the New Omega protector which;- * uarantees and improves the performance of the OME SUORTS. * Makes installation easier and aids the proper fitting of the support. sale Each Each Each Each Each sale Each Each Each Each Each S.S.316. sale Each Each Each Each Each Omega ceiling bracket T T E NEW NEW CLICK SYSTEM giving an easy and quick installation for LL of the trays on the market. Wire Mesh and Sheet Steel. NEW REINFORCE ROFILE increases the load capacity and the fitting of the tray. The supports can be easily stacked, thanks to the new profile and protector plug, therefore assisting in storage and logistics. Includes an Omega lug (pre-assembled) and the New Omega protector which;- * uarantees and improves the performance of the OME SUORTS. * Makes installation easier and aids the proper fitting of the support. sale Each Each Each Each Each sale Each Each Each Each Each S.S. 316 sale Each Each Each Each Each (*) The hot dip galvanized finish is NOT N CCURTE ESTHETIC FINISH. It is a very effective corrosion protection. COLOUR IFFERENCES CN OCCUR (shades of grey), brightness and surface finish (roughness, smoothness), created during the process employed. This is normal and does NOT FFECT THE QULITY N URTION OF THE NTI-CORROSION ROTECTION. 19

22 TENTO TENTO TENTO Omega pendant bracket T T E Light duty wall support NEW (Example) T T E NEW ESY INSTLL. Suitable for 35 and 60 flange. 100 and 150 wide. Finish sale BYCRO ack of ack of 25 Omega rotector NEW sale Each Each Each Each Omega lug T T NEW Each Each Each Each S.S Each Each Each Each New esign. rotects the installer when fitting trays. Mini universal bracket For installing boxes, use M5 bolts. New reinforced profile increases the load capacity. T T Material sale LSTIC ack of 50 revents the crushing of the SLUS Omega Bracket. vailable for Omega SLUS Brackets, SLUS Ceiling Brackets and SLUS Mesh Channel. Material sale LSTIC ack of 50 Finish sale Each Each S.S. 316 Each Light duty ceiling support ESY INSTLL. Suitable for 35 and 60 flange. 60, 100 and 150 wide. Side support 60 Stand off bracket T T E NEW Finish sale BYCRO ack of ack of 36 Essential for 60x60 wire mesh tray Finish sale E.B. Each Each S.S. 316 Each Finish sale Each Each S.S. 316 Each Each Each S.S. 316 Each BYCRO Electrolytic Bichromate BS-EN H... Hot-dip galvanised BS-EN-ISO 1461 E.B. Electrolytic Bichromate BS-EN S.S. assivated stainless steel ISI 304 or ISI 316 re-galvanised BS-EN E.. Electrogalvanised BS-EN 12329, available on request 20

23 TENTO TENTO TENTO TENTO Medium uty Cantilever SINLE SUORT COMTIBLE WITH LL TRY TYES. E.. WIRE MESH TRY, METL TRY, VC ETC. B NEW 7x20 x B sale 100x Each 150x Each 200x Each 300x Each 400x Each 500x Each 600x Each T T E Medium uty Cantilever H... and S.S. 316 B 43 12x16 30 NEW T T E 12x20 S.S. 316 x B sale x B sale 100x Each 150x Each 200x Each 300x Each 400x Each 500x Each 600x Each 7x x Each 150x Each 200x Each 300x Each 400x Each 500x Each 600x Each Heavy uty Cantilever x16 NEW T T E djustable Heavy uty Cantilever T T E x12 30 NEW 7x20 7x x B sale x B sale 300x Each 400x Each 500x Each 600x Each B B 100x Each 150x Each 200x Each 300x Each 400x Each 500x Each 600x Each (*) The hot dip galvanized finish is NOT N CCURTE ESTHETIC FINISH. It is a very effective corrosion protection. COLOUR IFFERENCES CN OCCUR (shades of grey), brightness and surface finish (roughness, smoothness), created during the process employed. This is normal and does NOT FFECT THE QULITY N URTION OF THE NTI-CORROSION ROTECTION. 21

24 Heavy duty pendant drop ouble heavy duty pendant drop kg sale Each Each kg sale Each Each Heavy duty pendant channel Heavy duty pendant boss Example M8x65 screws, not included (pag 27) 106 sale Each Each 106 sale Each Ceiling bracket Use with M8/M10 rods Variable ceiling rod bracket M8 Rod connector sale Each sale Each E.B. sale ack of 50 Threaded rod M6/M8/M10 E.B. kg x B sale 202 M6x Each 202 M6x Each 407 M8x Each 407 M8x Each 509 M10x Each E.. kg x B sale 202 M6x Each 202 M6x Each S.S. 316 kg x B sale 202 M6x Each 407 M8x Each 407 M8x Each 509 M10x Each BYCRO Electrolytic Bichromate BS-EN H... Hot-dip galvanised BS-EN-ISO 1461 E.B. Electrolytic Bichromate BS-EN S.S. assivated stainless steel ISI 304 or ISI 316 re-galvanised BS-EN E.. Electrogalvanised BS-EN 12329, available on request 22

25 TENTO TENTO Omega Mesh channel NEW T T E Hang with M10 threaded rod (age 15) kg sale 152/254(*) Each 152/254(*) Each 152/254(*) Each 254(**) Each 254(**) Each 152/254(*) Each 152/254(*) Each 152/254(*) Each 254(**) Each 254(**) Each NEW CLICK SYSTEM giving an easy and quick installation for LL of the trays on the market. Wire Mesh and Sheet Steel. NEW REINFORCE ROFILE increases the load capacity and the fitting of the tray. (*) Can be hung with 1 or 2 threaded rods. (**) Hang only with 2 threaded rods. Omega channel sale (length) m m m sale (length) m m m T T E Horizontal angle hanger assivated sale ack of ack of 100 Vertical angle hanger assivated sale ack of ack of 100 Beam clamp hanging assembly E.B. sale Each (*) The hot dip galvanized finish is NOT N CCURTE ESTHETIC FINISH. It is a very effective corrosion protection. COLOUR IFFERENCES CN OCCUR (shades of grey), brightness and surface finish (roughness, smoothness), created during the process employed. This is normal and does NOT FFECT THE QULITY N URTION OF THE NTI-CORROSION ROTECTION. 23

26 Light duty channel 41x21 e Light duty channel 41x41 e= 1.5 mm Length 3 mts. sale (length) m e= 1.5 mm Length 3 mts. sale (length) m Heavy duty channel 41x21 e= 2.5 mm Length 3 mts. sale (length) m m Heavy duty channel 41x m e= 2.5 mm Length 3 mts. sale (length) m S.S m S.S m Heavy duty channel 41x82 Spring channel nut 21 and Finish sale e= 2.5 mm Length 3 mts. sale (length) m ack of ack of ack of ack of 100 End plug 21 and 41 Spring channel screw 25 sale ack of Material sale lastic ack of lastic ack of 100 BYCRO Electrolytic Bichromate BS-EN H... Hot-dip galvanised BS-EN-ISO 1461 E.B. Electrolytic Bichromate BS-EN S.S. assivated stainless steel ISI 304 or ISI 316 re-galvanised BS-EN E.. Electrogalvanised BS-EN 12329, available on request 24

27 Splice plate N1 U shape splice plate N sale Each sale Each ngle bracket N3 ngle bracket N sale 98 sale Each Each 45º angle bracket N5 45º angle bracket N6 45º 45º sale Each 63 sale Each L Bracket N T joint N sale Each 104 sale Each T joint N9 3 Way Bracket N sale Each 41 sale Each (*) The hot dip galvanized finish is NOT N CCURTE ESTHETIC FINISH. It is a very effective corrosion protection. COLOUR IFFERENCES CN OCCUR (shades of grey), brightness and surface finish (roughness, smoothness), created during the process employed. This is normal and does NOT FFECT THE QULITY N URTION OF THE NTI-CORROSION ROTECTION. 25

28 Reinforced ngle Bracket N Clamp 41 N sale sale Each Each Clamp 82 N Clamp 21 N sale sale Each Each ouble 90º Bracket N15 90º Tee Bracket N sale 98 sale Each Each Channel floor boss 41x41 Channel floor boss 41x82 sale 88 sale 88 41x Each 41x Each Channel beam clamp sale Each djustable angle bracket 41x82 sale Each BYCRO Electrolytic Bichromate BS-EN H... Hot-dip galvanised BS-EN-ISO 1461 E.B. Electrolytic Bichromate BS-EN S.S. assivated stainless steel ISI 304 or ISI 316 re-galvanised BS-EN E.. Electrogalvanised BS-EN 12329, available on request 26

29 Washer Finish sale M E.. ack of 100 M E.. ack of 100 M E.B. ack of 100 M E.B. ack of 100 M ack of 100 M ack of 100 M S.S. 316 ack of 100 M S.S. 316 ack of 100 Serrated washer M8 M10 M10 Finish sale assivated ack of assivated ack of S.S. 316 ack of 100 llen screw E.. sale Hexagonal set screw M10x ack of 50 Finish sale Hexagonal cone point screw M10x20 E.B. sale ack of 10 Shoulder screw c/in 603 M6x12 M6x20 M6x20 M6x12 M6x20 M6x20 Finish sale E.. ack of E.. ack of E.B. ack of ack of ack of S.S. 316 ack of 100 M6x E.. ack of 100 M8x E.. ack of 100 M8x E.. ack of 100 M8x E.. ack of 100 M10x E.. ack of 100 M10x E.. ack of 100 M10x E.. ack of 100 M8x ack of 100 M8x ack of 100 M10x ack of 100 M10x ack of 100 M10x ack of 100 M8x S.S. 316 ack of 100 M8x S.S. 316 ack of 100 M10x S.S. 316 ack of 100 M10x S.S. 316 ack of 100 M10x S.S. 316 ack of 100 Serrated hexagon flange nut M6 M6 M6 M6 Finish sale E.. ack of E.B. ack of ack of S.S. 316 ack of 50 Hexagonal nuts Finish sale M E.. ack of 100 M E.. ack of 100 M E.B. ack of 100 M E.B. ack of 100 M ack of 100 M ack of 100 M S.S. 316 ack of 100 M S.S. 316 ack of 100 lain Channel nut M6 M8 M8 M8 M10 Finish sale E.. ack of E.. ack of ack of S.S. 316 ack of S.S. 316 ack of 100 (*) The hot dip galvanized finish is NOT N CCURTE ESTHETIC FINISH. It is a very effective corrosion protection. COLOUR IFFERENCES CN OCCUR (shades of grey), brightness and surface finish (roughness, smoothness), created during the process employed. This is normal and does NOT FFECT THE QULITY N URTION OF THE NTI-CORROSION ROTECTION. 27

30 030/ T T Click Joggled end coupling system for ease of connection without the need for additional couplers. emsa have optimized its range of metal tray by developing three different ranges of pemsaband : Metal tray with the base embossed and perforated, it comes packaged to protect the corners and interior parts and also to facilitate handling and transport. The slotted perforations provide maximum strength for equal weight and thickness. pemsaband SX has a new joggled coupling system which increases the ease of connection between lengths and substantially reduces installation time. Thanks to this Click system, you do not need any couplers just two screws for assembly. The range of pemsaband SX trays are designed and manufactured to the highest standards of quality, based on the product standard IEC This quality is confirmed by the N mark from ENOR, which guarantees all of its technical characteristics, and the E90 Fire Resistance Certification. Full range of heights 35, 60, 85 and 100. Widths of 100 to 600 mm. pemsaband RX High load capacity. Thickness = 1.5 mm. erforated and solid tray manufactured from thicker material to withstand higher loads. vailable in 60, 85 and 100 depths. pemsaband LX erforated and embossed tray with Rapid Click Coupling System in 35 and 60 depths. Overall length is 3.05 metres. BYCRO Electrolytic Bichromate BS-EN H... Hot-dip galvanised BS-EN-ISO 1461 E.B. Electrolytic Bichromate BS-EN S.S. assivated stainless steel ISI 304 or ISI 316 re-galvanised BS-EN E.. Electrogalvanised BS-EN 12329, available on request 28

31 030/ The base of the tray is embossed and perforated, certified by the ENOR N mark and E90 IN It comes packaged to protect the corners and interior parts and also to facilitate handling and transport. Finish 3001 T T Rapid Click Coupling System with 35 and 60 depths. xb Thickness (mm) H... Finish 3001 sale (length) 100x m 150x m 200x m 300x m 400x m 500x m 600x m 100x m 150x m 200x m 300x m 400x m 500x m 600x m Rapid Click Coupling System with 35 and 60 depths. System uses couplers with 85 and 100 depths. xb Thickness (mm) Connects with couplers and comes in 3 metre lengths. sale (length) 200x m 300x m 400x m 500x m 600x m 200x m 300x m 400x m 500x m 600x m On request ø8x20 Useful Tray = 3000 mm L=3050 mm B 50 Length 3050 mm. Useful Tray 3000 mm xb Thickness (mm) sale (length) 100x m 150x m 200x m 300x m 400x m 500x m 600x m 100x m 150x m 200x m 300x m 400x m 500x m 600x m System uses couplers with 85 and 100 depths. xb Thickness (mm) sale (length) 200x m 300x m 400x m 500x m 600x m 200x m 300x m 400x m 500x m 600x m On request ø8x20 Useful Tray = 3000 mm L=3050 mm B 50 (*) The hot dip galvanized finish is NOT N CCURTE ESTHETIC FINISH. It is a very effective corrosion protection. COLOUR IFFERENCES CN OCCUR (shades of grey), brightness and surface finish (roughness, smoothness), created during the process employed. This is normal and does NOT FFECT THE QULITY N URTION OF THE NTI-CORROSION ROTECTION. 29

32 solid Solid, smooth base tray certified by the ENOR N mark and E90 IN It comes packaged to protect the corners and interior parts and also to facilitate handling and transport. 030/ Finish 3001 Rapid Click Coupling System with 35 and 60 depths. T T xb sale (length) 100x m 150x m 200x m 300x m 400x m 500x m 600x m 100x m 150x m 200x m 300x m 400x m 500x m 600x m On request System uses couplers with 85 and 100 depths. xb sale (length) 200x m 300x m 400x m 500x m 600x m 200x m 300x m 400x m 500x m 600x m ø8x20 B Useful Tray = 3000 mm L=3050 mm Length 3050 mm. Useful Tray 3000 mm 50 H... Finish 3001 Connects with couplers and comes in 3 metre lengths. Rapid Click Coupling System with 35 and 60 depths. xb sale (length) 100x m 150x m 200x m 300x m 400x m 500x m 600x m 100x m 150x m 200x m 300x m 400x m 500x m 600x m System uses couplers with 85 and 100 depths. xb Thickness (mm) Thickness (mm) Thickness (mm) Thickness (mm) sale (length) 200x m 300x m 400x m 500x m 600x m 200x m 300x m 400x m 500x m 600x m On request ø8x20 Useful Tray = 3000 mm L=3050 mm B 50 BYCRO Electrolytic Bichromate BS-EN H... Hot-dip galvanised BS-EN-ISO 1461 E.B. Electrolytic Bichromate BS-EN S.S. assivated stainless steel ISI 304 or ISI 316 re-galvanised BS-EN E.. Electrogalvanised BS-EN 12329, available on request 30

33 EMS High load capacity. Thickness = 1.5 mm. erforated and solid tray manufactured from thicker material to withstand higher loads. The entire range can be supplied on request. vailable in 60, 85 and 100 depths CHECK VILBILITY NEW xb Thickness (mm) sale (length) 200x m 300x m 400x m 500x m 600x m 200x m 300x m 400x m 500x m 600x m 200x m 300x m 400x m 500x m 600x m xb Thickness (mm) sale (length) 200x m 300x m 400x m 500x m 600x m 200x m 300x m 400x m 500x m 600x m 200x m 300x m 400x m 500x m 600x m ø8x20 solid EMS NEW xb Thickness (mm) sale (length) 200x m 300x m 400x m 500x m 600x m 200x m 300x m 400x m 500x m 600x m xb Thickness (mm) sale (length) 200x m 300x m 400x m 500x m 600x m 200x m 300x m 400x m 500x m 600x m CHECK VILBILITY (*) The hot dip galvanized finish is NOT N CCURTE ESTHETIC FINISH. It is a very effective corrosion protection. COLOUR IFFERENCES CN OCCUR (shades of grey), brightness and surface finish (roughness, smoothness), created during the process employed. This is normal and does NOT FFECT THE QULITY N URTION OF THE NTI-CORROSION ROTECTION. 31

34 EMS erforated and embossed tray with Rapid Click Coupling System in 35 and 60 depths. Overall length is 3.05 metres. Finish 3002 xb Thickness (mm) sale (length) 100x m 150x m 200x m 300x m 400x m 500x m 600x m 100x m 150x m 200x m 300x m 400x m 500x m 600x m On request N E T T N E ø8x20 L=3000 mm 50 B Coupler Flange sale Flange sale Each Each Each Each Each Each Central joiner Use only with trays sale sale Each Each Each Each Each Each Each Each Universal bracket (pemsaband ) ø7x20 For installing boxes, use M5 bolts. sale Each Each Connector plate Suitable for mm I /Cu cables Finish sale E.B. ack of ack of 50 BYCRO Electrolytic Bichromate BS-EN H... Hot-dip galvanised BS-EN-ISO 1461 E.B. Electrolytic Bichromate BS-EN S.S. assivated stainless steel ISI 304 or ISI 316 re-galvanised BS-EN E.. Electrogalvanised BS-EN 12329, available on request 32

35 Reducer T T N E Facilitates the reduction of width in the pemsaband tray NEW The finish unit is supplied flat for later assembly. The H... finish unit is pre-formed. Reducer Flange Sale Reducer Flange Sale End cover T T N E NEW The finish unit is supplied flat for later assembly. The H... finish unit is pre-formed. Final end unit for the pemsaband tray system. Ensures overall security of the assembly. End Cover Flange Sale End Cover Flange Sale Cover Click fit cover remains fixed even in a vertical position 3m length sale ack (length) Unit m m m m m m m m 2 Click fit for fast fixing to tray. oes not require any additional nuts, bolts or clips sale (length) ack Unit m m m m m m m m 2 ivider, Click type T N E T 3m length sale (length) ack Unit m m m 12 sale ack (length) Unit m m m 12 (*) The hot dip galvanized finish is NOT N CCURTE ESTHETIC FINISH. It is a very effective corrosion protection. COLOUR IFFERENCES CN OCCUR (shades of grey), brightness and surface finish (roughness, smoothness), created during the process employed. This is normal and does NOT FFECT THE QULITY N URTION OF THE NTI-CORROSION ROTECTION. 33

36 B B 90º Bend Click T T The finish unit is supplied flat for later assembly. The H... finish unit is pre-formed. 90º Bend Click Cover Tee Click T T T T The finish unit is supplied flat for later assembly. The H... finish unit is pre-formed. xb sale 100x Each 150x Each 200x Each 300x Each 100x Each 150x Each 200x Each 300x Each 400x Each 500x Each 600x Each 200x Each 300x Each 400x Each 500x Each 600x Each 200x Each 300x Each 400x Each 500x Each 600x Each sale Each Each Each Each Each Each Each xb sale 100x Each 150x Each 200x Each 300x Each 100x Each 150x Each 200x Each 300x Each 400x Each 500x Each 600x Each 200x Each 300x Each 400x Each 500x Each 600x Each xb sale 100x Each 150x Each 200x Each 300x Each 100x Each 150x Each 200x Each 300x Each 400x Each 500x Each 600x Each 200x Each 300x Each 400x Each 500x Each 600x Each 200x Each 300x Each 400x Each 500x Each 600x Each sale Each Each Each Each Each Each Each xb sale 100x Each 150x Each 200x Each 300x Each 100x Each 150x Each 200x Each 300x Each 400x Each 500x Each 600x Each 200x Each 300x Each 400x Each 500x Each 600x Each Tee Click Cover T T sale Each Each Each Each Each Each Each sale Each Each Each Each Each Each Each (*) The hot dip galvanized finish is NOT N CCURTE ESTHETIC FINISH. It is a very effective corrosion protection. COLOUR IFFERENCES CN OCCUR (shades of grey), brightness and surface finish (roughness, smoothness), created during the process employed. This is normal and does NOT FFECT THE QULITY N URTION OF THE NTI-CORROSION ROTECTION. 35

37 Side Entry Click B Side entry Click Cover Crossover Click Crossover Click cover T T T T Creates a Tee at any point using trays of different widths (e.g ) T T T T The finish unit is supplied flat for later assembly. The H... finish unit is pre-formed. The finish unit is supplied flat for later assembly. The H... finish unit is pre-formed. B xb sale 100x Each 150x Each 200x Each 300x Each 100x Each 150x Each 200x Each 300x Each 400x Each 500x Each 600x Each 200x Each 300x Each 400x Each 500x Each 600x Each 200x Each 300x Each 400x Each 500x Each 600x Each sale Each Each Each Each Each Each Each xb sale 100x Each 150x Each 200x Each 300x Each 100x Each 150x Each 200x Each 300x Each 400x Each 500x Each 600x Each 200x Each 300x Each 400x Each 500x Each 600x Each sale Each Each Each Each Each Each Each xb sale 100x Each 150x Each 200x Each 300x Each 100x Each 150x Each 200x Each 300x Each 400x Each 500x Each 600x Each 200x Each 300x Each 400x Each 500x Each 600x Each 200x Each 300x Each 400x Each 500x Each 600x Each sale Each Each Each Each Each Each Each xb sale 100x Each 150x Each 200x Each 300x Each 100x Each 150x Each 200x Each 300x Each 400x Each 500x Each 600x Each 200x Each 300x Each 400x Each 500x Each 600x Each sale Each Each Each Each Each Each Each BYCRO Electrolytic Bichromate BS-EN H... Hot-dip galvanised BS-EN-ISO 1461 E.B. Electrolytic Bichromate BS-EN S.S. assivated stainless steel ISI 304 or ISI 316 re-galvanised BS-EN E.. Electrogalvanised BS-EN 12329, available on request 36

38 Inside Riser Click T T xb sale 100x Each 150x Each 200x Each 300x Each xb sale 100x Each 150x Each 200x Each 300x Each B 100x Each 150x Each 200x Each 300x Each 400x Each 500x Each 600x Each 100x Each 150x Each 200x Each 300x Each 400x Each 500x Each 600x Each The finish unit is supplied flat for later assembly. The H... finish unit is pre-formed. 200x Each 300x Each 400x Each 500x Each 600x Each 200x Each 300x Each 400x Each 500x Each 600x Each Inside Riser Cover Click Outsider Riser Click T T T T The finish unit is supplied flat for later assembly. The H... finish unit is pre-formed. B sale Each Each Each Each Each Each Each xb sale 100x Each 150x Each 200x Each 300x Each 100x Each 150x Each 200x Each 300x Each 400x Each 500x Each 600x Each 200x Each 300x Each 400x Each 500x Each 600x Each sale Each Each Each Each Each Each Each xb sale 100x Each 150x Each 200x Each 300x Each 100x Each 150x Each 200x Each 300x Each 400x Each 500x Each 600x Each 200x Each 300x Each 400x Each 500x Each 600x Each Outside Riser Cover Click T T sale Each Each Each Each Each Each Each sale Each Each Each Each Each Each Each (*) The hot dip galvanized finish is NOT N CCURTE ESTHETIC FINISH. It is a very effective corrosion protection. COLOUR IFFERENCES CN OCCUR (shades of grey), brightness and surface finish (roughness, smoothness), created during the process employed. This is normal and does NOT FFECT THE QULITY N URTION OF THE NTI-CORROSION ROTECTION. 37

39 inducanal cover 3m length sale ack (length) Unit m 8 inducanal 3001 Central hanging plate 7 E.. B ( M6= Ø 7x14 ) sale M ack of 20 ø8x20 90 Threaded rod M6 ø ø21 Safety edge xb sale ack (length) Unit. 60x m 8 Well-finished side/edge USH E.. xb sale M6x Each M6x Each E.B. xb sale M6x Each M6x Each Universal bracket Coupler see page 32 see page 32 Self fix lid cover BYCRO Electrolytic Bichromate BS-EN H... Hot-dip galvanised BS-EN-ISO 1461 E.B. Electrolytic Bichromate BS-EN S.S. assivated stainless steel ISI 304 or ISI 316 re-galvanised BS-EN E.. Electrogalvanised BS-EN 12329, available on request 38

40 Inducanal 90º Bend Inducanal 90º Bend Cover T T T T xb sale 60x Each sale Each Inducanal Side Entry Inducanal Side Entry Cover T T T T xb sale 60x Each sale Each Inducanal Inside Riser Inducanal Inside Riser Cover T T T T xb sale 60x Each sale Each Inducanal Outside Riser Inducanal Outside Riser Cover T T T T xb sale 60x Each sale Each (*) The hot dip galvanized finish is NOT N CCURTE ESTHETIC FINISH. It is a very effective corrosion protection. COLOUR IFFERENCES CN OCCUR (shades of grey), brightness and surface finish (roughness, smoothness), created during the process employed. This is normal and does NOT FFECT THE QULITY N URTION OF THE NTI-CORROSION ROTECTION. 39

41 Range Overview Flexible Conduit System Conduits, Connectors and accessories. emsaflex has a wide range of conduits, connectors and accessories, manufactured in polyamide and other engineering plastics that provide different solutions in industrial environments. emsaflex is characterized by a wide range of connectors and accessories that perfectly complement the protection of the wiring installation. ngle connectors 45º and 90º, plastic and metallic threads and other special fittings increase the range available. These connectors and accessories use the Click System that allows fast and easy assembly, providing excellent levels of protection. Within the emsaflex range, you can find Conduits systems in other plastic materials such as TF Conduit or metal flexible conduits such as the TM and TM-VC, focused for applications with high mechanical requirements and strong protection. These Conduit systems are manufactured and tested under the features detailed within IEC61386 standards under the CE marking according to the European directive on low voltage. emsa manufactures under the ISO 9001 quality standard, ensuring they provide a high level of technical excellence whilst making their products highly competitive. dvantages Wide range of types and sizes. Excellent properties, and flexibility. Quick and easy installation. Excellent Cable protection and liquid and solid tight. 40

42 Surface treatment to prevent corrosion ll the steel products made by EMS are protected by one of the following coatings: Sendzimir alvanizing BS-EN (NOT TO BE CONFUSE WITH HOT-I LVNIZIN) Used solely for protecting sheet metal of below 3 mm in thickness. roduced by dipping the rolls of steel in a zinc bath at 450 ºC. This technique is widely used in the manufacture of bar-cut parts and stamped parts. The cuts arising in the machining are partially regenerated by the galvanic pair formed by the steel and the zinc. The thickness of the protective coating is from 8 to 15 microns. Recommended for indoor installations in a dry atmosphere with no aggressive contaminants. BYCRO/E.B. Electrogalvanized bichromate (yellow colour) BS-EN This involves the above process plus subsequent treatment that improves the anti-corrosion performance - see table II. The thickness of the coat applied is 8-12 microns. The process as used by EMS involves no CYNIE and no CHROME VI. Recommended for use in dry, contaminant-free atmospheres. Better performance than and E.. E.. Electrogalvanizing (white colour) BS-EN This involves protecting parts made of iron and steel electrolytically using zinc. The thickness of the coating applied varies from 8 to 12 microns - see table I. The Standard recommends applying a chrome-conversion layer (BS ). To solve this problem, after the manufacturing work (punching, welding), EMS subjects all its rejiband S.S. rack and accessories to a special process, known as THERMICRON, for regenerating the protective layer. 304 STINLESS STEEL ISI-304 Suitable for: Fresh water Industrial atmosphere Normal chemical industry Food industry (except high temperatures). 316 STINLESS STEEL ISI-316 Specially recommended for marine and coastal areas, aggressive chemical environments and high temperature food applications. Laboratory tests carried out in a salt-spray chamber in accordance with STM-B117 produced the following results: TBLE I Corrosion resistance in hours E.B./BYCRO Electrolytic zinc coating, birchromate (yellow) 440 E.. Electrolytic zinc coating (white) 290 H... Hot-dip galvanizing >600 SS Stainless steel ISI 316 No trace after 450 * the oxidation stopped when in contact with circulating air. Recommended for indoor installations in a dry atmosphere with no aggressive contaminants. H... Hot-ip alvanizing BS-EN ISO 1461 Used for all kinds of products. It involves immersing the individual pieces to be protected into a bath full of zinc at 450 ºC after the parts have been machined. The average thickness of the protective coating is 70 microns. Recommended for outdoor, marine, rural, industrial and aggressive indoor installations. STINLESS STEELS These are carbon steels alloyed with chromium, nickel, magnesium and molybdenum. The best-known ones are ISI 304 (18/8) and ISI 316. Contrary to widespread belief, these steels LSO SUFFER CORROSION, though their performance when properly handled is generally much better than any type of protective coating. Their specific behaviour is the result of the chromium and nickel spontaneously generating a film of chromium oxide in the presence of an oxidising environment, this film then preventing subsequent oxidisation. The film is very delicate, and can be broken by blows, machining, welding etc. Stainless steels are easily CONTMINTE, thus losing their properties, when they are machined with tools that use other types of steel. In such cases, the protective film must be generated by a chemical-attack process. 41

43 pemsa CORROSION E.B./BYCRO 440 E HOURS Recommendations for the correct installation of cable trays (BS-EN 61537, BS , REBT 2002, ITC-BT 20 and 21) Standards 1.- LOCTION Must NOT be installed under water, steam, gas, tubing, etc ISTNCE BETWEEN TRYS For correct cable ventilation, at least the minimum distance indicated in the drawing must be maintained. Rejiband Security emsa Rejiband Security emsa Rejiband Security emsa Rejiband Security emsa 2.- ROTECTION The trays are for conveying cables, NOT FOR ROTECTIN THEM. In the majority of installations, the characteristics of current cables makes it unnecessary to protect them. If necessary, use the appropriate covers. 3.- VENTILTION Cables heat up while being used due to the passage of current. t the same ambient temperature and power, this heating can increase according to the type of tray being used (open or closed). With less ventilation, a greater cable cross section is required and, as a result, cost increases ISTNCE TO WLLS When trays are fastened to a wall on supports, a separation of at least 20 mm must be maintained between the tray and the wall in order to allow for cable ventilation. t EMS, all wall supports have a total length of 50 mm more than the width of the tray to be installed, thereby complying with legislation in force. Example: 300 support has a length of 350 mm. Maximum ventilation: rejiband or ladder-type trays. Medium ventilation: perforated metal sheet trays. Minimum ventilation: solid metal sheet trays. The use of solid bottom trays is, in most cases, due to aesthetic criteria. Voice-data cables Line 7/3 lant 7 (Company) 4.- MRKINS Trays should facilitate labelling through markings. 42

44 TENTO 5.- SUORTS These are fundamental in a tray installation. If they are not suitable, the whole installation will be flawed. The following factors should be borne in mind when choosing them: The load-bearing capacity of the support. Its corrosion resistance. Ease of installation. The recommended distance between supports or bearing points is normally 1500 mm. When this distance is changed, the performance of the tray changes. When attaching the supports to the wall or ceiling, particular attention must be paid to the fixings used, making sure it is right for the characteristics of the building. The use of CHNNEL gives better load distribution, whilst also facilitating adjustment. 6.- RECOMMENE OSITIONS FOR SUORTS (Same for rejiband steel wire cable trays) 7.- TRY N SUORT EFORMTION The weight of cables deforms trays, the most visible point being in the centre between supports. The allowable value (F) of deformation is purely aesthetic, always taking care not to exceed the values indicated by the manufacturer, which, in accordance with international standard BS F max=l/100 mm. EN 61537, should be as follows: On supports, maximum F deformation and twisting occurs at the ends. The standard requires that the maximum F = L/20 mm. The deformation, F is called deflection, and is expressed in mm. T T E T T The designs, products and technical information contained in this document are protected by intellectual property rights and include the following utility models: , , , , , , , , , , , , , , , , , , , , ,

45 8.- CONNECTORS The trays are shipped in pre packed lengths of 2 or 3 metres. The pieces called CONNECTORS are used for connecting them. For mechanical purposes, the weakest points in a tray installation are the joints. Only the use of the right number of CONNECTORS in the right positions as recommended by the manufacturer can ensure that the entire system will perform satisfactorily. The ideal spot for employing the CONNECTOR is at L/5 from the nearest support. Fitting the CONNECTORS between L/4 and L/5 is the most advisable approach. LL THE LO N ERFORMNCE VLUES IVEN IN THIS CTLOUE WERE OBTINE FROM TESTS CRRIE OUT IN CCORNCE WITH INTERNTIONL EN STNR. It is often found that similar trays from different manufacturers give different values. This may be due to the load tests not being carried out in accordance with this standard. For proper comparisons to be made between two similar trays from different manufacturers, check that the values given were found under equivalent test conditions ERTHIN (ELECTRICL CONTINUITY) ll metal tray systems must have proper electrical continuity. However, to ensure safety, it is advisable to make an earth connection using a suitable conductor for each part of the system. This CNNOT be done on painted or epoxy-coated trays without removing the protective layer at that point and at the join-points between the various lengths, which will inevitably lead to oxidisation WITHOUT ENSURIN safety. The CONNECTORS should NOT be fitted at point L/2 (halfway between the supports), or on the supports. When L=1.5 metres, which is the commonest case, the use of 3-metre lengths ensures the best placing of the joints, unlike using 2-metre lengths. L/2 L NO 11.- THROUH-WLL MOUNTIN When the trays have to go through a wall, the trays should have a clear space of approximately 100 mm on each side. The earth connection must always be maintained. L/2 L NO If the characteristics of the two rooms separated by the wall are different and may pose risks associated with moisture, gas or fire, the hole in the wall should be blocked off using suitable systems from among those available. 9.- LO-BERIN CCITY This is the load (uniformly distributed, NOT concentrated) that a tray can safely cope with. It is expressed in kilos or kg per running metre, in the form of graph curves or tables. 1 kg = 9.81 Newtons The values are obtained through experiments carried out in accordance with the pertinent standards. 44

46 Rejiband 35 E.., BYCRO and H... Width: MXIMUM SFE WORKIN LO (Kg/m) STINLESS STEEL Width: kg = 9.8 N Kg/m Kg/m ,0 1,5 2,0 istance between supports (metre) 15 1,0 1,5 2,0 istance between supports (metre) 15 Rejiband 60 MXIMUM SFE WORKIN LO (Kg/m) 1 kg = 9.8 N E.., BYCRO and H... Width: ,0 1,5 2,0 istance between supports (metre) Kg/m STINLESS STEEL Width: ,0 1,5 2,0 istance between supports (metre) Kg/m Rejiband 100 MXIMUM SFE WORKIN LO ((Kg/m) 1 kg = 9.8 N E.., BYCRO and H... Width: STINLESS STEEL Width: ,0 1,5 2,0 istance between supports (metre) Kg/m ,0 1,5 2,0 istance between supports (metre) Kg/m Values obtained from test according to the UNE-EN standard, with a safety coefficient of 170% without ever reaching the collapse point. uaranteed only using our reinforced joint clamp. Tray section joints be situated at a support distance of between L/4 and L/5, L being the distance between supports. t completed tray extreme ends, tray support distance should be a maximum of 0.4L without any type of joint. 45

47 Horizontal Wall assembly Side Support 60 Mini Universal Bracket Omega Bracket Omega Bracket on channel dmissible load❶ 25 Kg 50 Kg 59/167 Kg 59/167 Kg Fitting to ceiling dmissible load❶ with threaded roods 25 Kg 89 Kg 89 Kg 69 Kg + ESY CBLE LYIN Omega System Fitting to ceiling Vertical Force ❶ * Bending moment 1 ❷ **Bending moment 2 ❷ 32/96 Kg /382 Kg 20 Kg x m 11 Kg x m 338 Kg 42 Kg x m 16 Kg x m 338 Kg 42 Kg x m 16 Kg x m 46 Mounting with rejiband Mounting with pemsaband ❶ Values obtained from test according to the UNE-EN with a safety coefficient of 170% without ever reaching the collapse point. uaranteed only for our hanger with security plug and supports reinforced with the EMS structural reinforcement.

48 TENTO Identification Label N E T T N E rotector (for ends & edges) Material sale LSTIC ack of 50 sale m length Supplied in 10m lengths Riser/ropper rotector EMS Flange sale Each Each Bolts not included Four units required for each Riser/ropper EMS EMS Each Each rejiband pemsaband joint 3301 T T NEW Finish sale Each (**) Each (**) (**) Each package contains two parts, one for each flange. Special joint for coupling rejiband directly to pemsaband. djustable bend Click Variable angle 90º-180º T T E Side Entry rejiband pemsaband T N E T xb Flange NEW Sale 100x x x x x x x x xb Flange Sale 100x x x x x x x x xb Flange Sale 100x x xb Flange Sale 100x x NEW BYCRO Electrolytic Bichromate BS-EN H... Hot-dip galvanised BS-EN-ISO 1461 E.B. Electrolytic Bichromate BS-EN S.S. assivated stainless steel ISI 304 or ISI 316 re-galvanised BS-EN E.. Electrogalvanised BS-EN 12329, available on request 34

49 Sloping Vertical Rejiband Security emsa Medium uty Cantilever Heavy uty Cantilever djustable Heavy uty Cantilever Mini Universal Bracket Stand off Bracket 119/254 Kg 119/254 Kg 121/206 Kg 50 Kg 100 Kg REINFORCE SUORTS RETER LO-BERIN CCITY with threaded roods 69 Kg 78 Kg 176/196 Kg 176/332 Kg 432/489 Kg + SSEMBLY TIME SVIN reinforced supports 378 Kg 36 Kg x m 44 Kg x m 378 Kg 36 Kg x m 44 Kg x m 428 Kg 93 Kg x m 73 Kg x m 428 Kg 93 Kg x m 73 Kg x m 70 Kg - - REINFORCE SUORTS RETER LO-BERIN CCITY ❷ Values obtained in accordance with International Standard UNE - EN (Section H) relating to the information for safe installation of trays with horizontal supports. For further information please contact EMS. * Bending moment 1 : Resulting bending moment on ceiling plane. * Bending moment 2 : Resulting bending moment from cantilever bracket. 47

50 Fire Resistance rejiband Safety is a growing concern within electrical installations. In the event of a fire the behaviour of electrical equipment, when exposed to high temperatures, determines whether the installation achieves a certain safety level. rejiband wire mesh cable tray complies with these requirements with a number of features and properties as described in the E90 Certification. rejiband wire mesh cable tray is manufactured in accordance with the requirements and tests of the product standard IEC "Cable Tray and Cable Ladder Systems". So far this standard has not yet covered the fire risks and fire resistance. IN Cable Tray and Cable Ladder Systems E30 E60 When studying the properties of rejiband wire mesh cable tray against fire, emsa has used the erman Standard IN which is the main reference in other European countries. This standard tests the complete installations, in order to evaluate the structural integrity of the assembly and how the components react when exposed to fire. 3m length of wire mesh tray, accessories and power cables are the subject of the test. ccording to the final results, the certification may be issued at three different levels: Table 1. Standards. STNRS E30 E60 E90 Time 30 min. E660 min.0 E990 min.0 Temperature 840 ºC 950 ºC 1000 ºC0 The purpose of this test is to validate the correct operation of the electrical system and to ensure that critical services (fire suppression system, emergency lighting, ventilation and other basic installations) remain functional for long enough to organise evacuation in the event of fire. 48

51 Fire Resistance Figure 1: eneral View Of The ssembly Test Set-up The test set-up consisted of a 3m length of wire mesh tray, including joints and accessories, supported on brackets at intervals of 1.2m. The power cables, up to 1kV, should be fire resistant at the same or higher level than halogen free, high safety cables. The wire mesh tray was then loaded with chains to simulate the cable weight and other standard conditions of the test. uring the test, a standardised temperature vs. time curve is imposed in the test oven, obtaining the 3 levels of certification and their corresponding times and temperatures as shown on table 1. The results prove that the cables maintain electrical continuity during the test, and therefore the operational integrity of the installation is maintained. s the test was progressing, both cables and trays were damaged by the high temperatures as defined in IN Trays are deformed but maintain their support function. The cable sheathing starts to burn causing risk to the correct functioning of the system. Figure 2: ssembly Before Test s shown in figure 3, rejiband wire mesh cable tray and its accessories neither collapsed nor were they detached from the supports, ensuring enough structural resistance within the system. Conclusions Figure 3: ssembly fter Test rejiband The wire mesh cable tray exceeded the fire resistance test, qualifying for the highest level of resistance proposed by this standard, the E90. The tray with cables were tested for 90 minutes at temperatures of 1000ºC (in accordance with the conditions of IN ), maintaining circuit integrity against fire. The combined use of rejiband wire mesh tray with high safety halogen-free electrical cables improves substantially the safety of the installation. Since both components provide a self extinguishing system, which does not produce toxic, corrosive or opaque fumes (more typical for polymeric & halogen materials), this allows a period of time long enough for evacuation and emergency works. Investing in safety equipment and systems with high fire resistance must be accompanied by a safe installation that ensures their correct functioning in the most critical situations. 49

52 To ensure electrical safety in a cable-carrying tray installation, the installation must have suitable electrical continuity. Electrical continuity The design of the joining has decisive importance in the R1 value, as do the material, the surface finish and the method of assembly. This is stipulated in Standard IEC section 11.1, which gives the pertinent tests for checking this. This is done in this way: measuring the electrical-resistance values at the most unfavourable point R1 (joining between racks) and R2 (material resistance) measured across two points that are 500 mm apart in the same straight run. Contact between different materials or finishes encourages oxidisation, thereby reducing electrical continuity. The same condition may arise through insufficient contact pressure at the join point. O NOT SSEMBLE TRYS N JOINTS WITH IFFERENT FINISHES The maximum admissible values according to IEC are: R1< 50 mω R2< 5 mω R 1 R 2 In tests performed at emsa s request in the Central Laboratory of the Electrical Engineering Office under number on 10/12/99, involving various samples of rejiband and pemsaband., the values given in the following tables were found: Rack mm Connector used and number Tigtening torque at connectors RESISTNCE (mω) R1 R2 4 connectors 3 Nm x60 E.B. / BYCRO 4 connectors 2 connectors REJIBN SECURITY - 3 Nm x60 REJIBN 2 connectors REJIBN SECURITY connectors 3 Nm H x60 REJIBN SECURITY 4 connectors EMSBN Inox x60 100x60 400x60 2 connectors 2 connectors 2 side connectors 3 Nm 3 Nm 3 Nm central connector 50

53 EMS Earthing If it is deemed, in view of the installation, to be necessary to have an independent earth conductor, its section must be at least 16 mm 2, and must be mounted on the outside throughout the tray system, connected using the right accessories to each length of the installation. cable-carrying tray system comprises straight lengths and accessories (bends, crossovers, Tee-joints) joined together using suitable fasteners. The electrical continuity in the system ifself (in the case of metal trays), which is necessary to achieve proper earthing and to ensure personal safety, can be adversely affected by a wide range of causes (oxidisation, nuts coming loose, insulating coatings, etc.). To avoid this, it is advisable to install an independent earth circuit by connecting up every single element in the system (trays and accessories) to a suitable sized conductor - with a section of at least 16 mm 2. In the case of trays that are painted or coated with epoxy resin, the electrical continuity needed in the system is broken. In such cases, arranging an earth connection is absolutely essential. That is a difficult operation, since it can only be done by removing the protective layer by mechanical means at the earth-connection point. This inevitably creates an oxidisation zone which further hinders the earthing. That is why electrically safe tray systems must be made of metal with metal coating or made solely of insulating material. The earth connection is to be made using the right parts - rejiband or pemsaband. Rejiband emsaband 51

54 Electromagnetic Compatibility (CEM) ower supply cables and signal cables can share the same cable conveyance systems (Trays, Channels, etc.). dequate separation must be provided (by distance or shielding) between power cables and signal cables. ower cables and signal cables must cross at right angles. In order to prevent disturbances, the minimum separation between power cables and signal cables depends on many factors, such as the following: a) The level of immunity from the various electromagnetic interference (surges, overcurrents, lighting impulses, ring waves, continuous waves, etc.) of the equipment connected to the signal cabling system. b) The connection of the equipment to the grounding system. c) The local electromagnetic environment (the simultaneous appearance of disturbances: for example, harmonics added to discharges and to continuous waves). d) The electromagnetic spectrum. e) The distances that the cables run parallel to each other (the coupling zone). f) The kind of cable. g) Cable attenuation against coupling. h) The quality of the connections between the connectors and the cable. i) The type of cable conveyance system and its accessories. Separation between signal cabling and power cabling istance Type of instalation Unshielded power cable and unshielded signal cable Unshielded power cable and shielded signal cable (2) Shielded power cable and unshielded signal cable Shielded power cable and shielded signal cable (2) Without a dividing wall or with a non metal divider(1) luminium divider Steel divider 200 mm 100 mm 50 mm 50 mm 20 mm 5 mm 30 mm 10 mm 2 mm 0 mm 0 mm 0 mm 1) It is assumed that in the event of a metal divider, the design of the cable conveyance system will provide shielding attenuation that is approximate to the material used in the divider. 2) Shielded signal cables must comply with the EN series. 52

55 Electromagnetic Compatibility (CEM) Metal systems for cable conveyance: trays, channels, etc. Metal systems for cable conveyance should always be connected to the local ground at both ends. Over long distances (more than 50 m), additional connections to the ground systems are recommended at irregular intervals. ll ground connections should be as short as possible. Non-metal systems for cable conveyance: trays, channels, etc. In order to improve the EMC behaviour of non-metal systems for cable conveyance, when devices connected to the wiring systems with unshielded cables are not affected by low frequency disturbances, it is advisable to add a cable to the cable conveyance system, such as a parallel ground conductor connected at both ends to the local ground system. Connections should be made to metal parts with low impedance (for example, to a large piece of the sheet metal of an electrical cabinet). The parallel ground conductor should be designed to resist the common mode and fault currents. rounds and equipotential connections Overview. The basic purposes of connection and grounding applicable to unshielded and shielded wiring systems are as follows: - Safety: to limit contact voltage and provide a return path in the event of a fault to ground; - EMC: to have zero potential and equipotentiality, which provide a shielding effect. Source: UNE-EN Rejiband installed with a divider. 53

56 roduct Index by escription roduct age roduct age 3 Way Bracket N Tee Bracket (N16) and double (N15) 26 dhesive & Hardener 17 ngle Bracket N3 and N4 25 ngle Bracket, 45º N5 and N6 25 ngle Hanger, Horizontal and Vertical 23 ngle Tray 10 ngle Tray Fastener 13 ngle Bracket, djustable 26 ngle Bracket, reinforced N11 26 Beam Clamp Hanging ssembly 23 Bend 90º 35 Bend 90º, Inducanal 39 Bend Click, djustable 34 Bolt Cutters 10 Box Support for rejitech 18 Box Support for rejiband 15 Ceiling Fastener (rejitech ) 18 Ceiling Bracket 22 Central Hanging late Central Joiner 32 Central Suspension, Click 15 Channel 41x21 and 41x41, Heavy uty 24 Channel 41x82, Heavy uty 24 Channel 41x21 and 41x41, Light uty 24 Channel Beam Clamp 26 Channel click joint 12 Channel Floor Boss 41x41 and 41x82 26 Channel Nut, lain 27 Clamps 21, 41 and 82 (N12, N13 and N14) 26 Connector, E90 RLUS and SLUS 12 Connector late Connector, Click 13 Coupler Cover, 90º Bend 35 Cover, 90º Bend, Inducanal 39 Cover, Crossover 36 Cover, inducanal 38 Cover, Inside Riser Click 37 Cover, Inside Riser Inducanal 39 Cover, Side Entry 36 Cover, Side Entry Inducanal 39 Cover, Tee 35 Cover, Tray Cover, Outside Riser Click 37 Cover, Outside Riser Inducanal 39 Crossover 36 Channel, Omega SLUS 23 ata Outlet 16 ivider, Click Type End Cover 33 End plug 21 and Earth Terminal Fast click joint 11 Fast click base joint 11 Fixing Support for rejiband 15 Floor Foot 17 land Bracket Heavy uty Cantilever RLUS 21 Heavy uty Cantilever adjustable RLUS Heavy uty endant Boss 22 Heavy uty endant Channel 22 Heavy uty endant rop 22 Heavy uty endant rop, ouble 22 Identification Label Identification late 16 inducanal 38 Inside Riser Click 37 Inside Riser, Inducanal 39 Joint Clamp, Reinforced 13 Joint, rejiband pemsaband L Bracket N7 25 Light duty ceiling support Light duty wall support Luminaire and box support 12 Medium uty Cantilever RLUS 21 Mesh Channel, Omega SLUS 23 Nut 21and 41, spring channel 24 Nuts 27 Omega Bracket universal SLUS 19 Omega Ceiling Bracket SLUS 19 Omega endant Bracket SLUS 20 Outside Riser Click 37 Outside Riser, Inducanal 39 art Clamp 13 pemsaband SX 28 pemsaband SX solid 30 pemsaband RX 31 pemsaband LX 32 lug, Omega 20 rotector 34 rotector, Omega 20 Reducer 33 rejiband 9-10 rejiband False Floor 17 Rejifix rejitech Riser / ropper 34 Rod Connector, M8 22 Screw, spring channel 24 Screws 27 Side Entry Click 36 Side Entry, Inducanal 39 Side Entry rejiband pemsaband 34 Side Joint late 13 Side Support Splice late 13 Splice late N1 25 Stand Off Bracket 20 Tee 35 T Joint N8 and N9 25 Threaded Rod U shape splice late N2 25 Universal Bracket Universal Bracket, Mini Variable Ceiling Rod Bracket 22 Washers 27 Wire End Cap 13 Zinc aint Spray 16

57 TERMS N CONITIONS 1 Interpretation 1.1 In these Conditions, unless the context otherwise requires: "the Company" means emsa UK Limited of Unit 2, Hunslet Trading Estate, Severn Road, Leeds, LS10 1BL; "the Customer" means the person, firm or corporation with whom the Company contracts for the sale of the oods upon these Conditions; "the oods" means the goods (including any instalments of the goods or any part of them) which the Company is to manufacture and supply to the Customer in accordance with the Contract; "the Contract" means the contract for the sale and purchase of the oods by the Customer; "Business day" means any day other than Saturday, Sunday or a bank or public holiday. 2 Limitation of Contract 2.1 ll orders accepted by the Company shall be based upon these Conditions which shall override and take the place of any other terms or conditions produced or referred to by the Customer. 2.2 If the Customer places an order with which the Company wishes to proceed, an order confirmation (the Confirmation ) will be sent to the Customer containing details of the order. The Confirmation in con junction with these Conditions shall form the basis of the contract between the Company and the Client. In the event of any conflict or inconsistency between these Conditions and the terms of the Confirmation, the terms of the Confirmation shall prevail. No variations shall be binding unless agreed in writing between authorised representatives of the Company and the Customer. 2.3 ll representations, whether written or oral, made prior to the acceptance of the Customer's order by the Company are expressly excluded from the Contract, unless otherwise agreed in writing by both parties. 2.4 No variation of or addition to these Conditions shall be binding unless agreed in writing between an authorised representative of the Company and the Customer, and no order placed may be cancelled, deferred or varied without the written agreement of an authorised representative of the Company 3 rices 3.1 ll prices quoted, price lists or estimates (whether written or oral) issued by the Company from time to time shall not bind the Company and the price charged may be adjusted to take account of any fluctuations in VT, government duties or in the cost of manufacture unless the price was stated to be fixed and the Customer has complied in all respects with the terms and conditions specified by the Company subject to which the price was stated to be fixed. 3.2 Where oods are to be delivered to a destination outside the United Kingdom, prices unless expressly stated to be otherwise, are ex-works. 3.3 ll prices quoted are exclusive of VT and will be subject to VT at the rate in force at the time. 4 Cancellation 4.1 The Customer may cancel an order once accepted, however, cancellation of the order by the Customer for whatever reason shall entitle the Company to recover for any loss of profit and all costs, charges and expenses incurred by the Company in respect of the order up to the date of receipt by the Company of written notification of cancellation from the Customer. 5 cceptance 5.1 The Company routinely inspects any oods supplied to the Customer. If the Customer requests any bespoke or specialist testing the additional costs or expenses if any, incurred by the Company shall be charged to the Customer in addition to the price. 5.2 In the event that the Customer requires the testing to be carried out in its' presence or before a representative then the Customer shall attend at the Company's premises upon the Company giving notice of availability of the oods for testing within 7 days of the date of the notice. If the Customer does not attend or if within 14 days of the Customer having attended the Customer does not notify the Company that the oods do not accord with the Contract specifying reasons, then the Customer shall be deemed to have accepted that the oods are in accordance with the Contract and shall not be entitled to reject them or to claim damages or compensation from the Company on the grounds of anything which the testing revealed or would have revealed if it had been carried out. 5.3 Irregardless of the above, the Customer shall inspect the oods immediately upon their arrival at the delivery destination in order to ascertain: that the number of items and packages and the quantities are as specified and the oods are as described in the Company's delivery note; whether the oods have been damaged in transit; that the oods are those specified in the Customer's order stated on the Company's elivery Note. ny discrepancy between the oods delivered and those described in the Company's delivery note and any damage to the oods in transit must be notified to the Company in writing within three Business ays of receipt of the oods. In the case of oods dam aged in transit, the Customer shall retain the damaged oods for a period of one month from the date of receipt by the Customer during which period the Customer will permit the Company and its representatives to examine the oods and any damage to them incurred in transit. In the case of non-delivery of the oods the Customer must notify the Company in writing within 10 Business ays of the receipt by the Customer of the Company's delivery note. 5.4 The Customer shall be deemed to have accepted the oods as being in accordance with the Contract unless within 10 Business ays of receipt of the oods the Customer notifies the Company in writing of any defect in materials or workmanship or failure to comply with designs, drawings, specifications or other data supplied by the Customer or any other failure of the oods to conform with the Contract which would be apparent upon such inspection and testing as it is reasonable for the Customer to undertake within such 10 Business ays. 5.5 Where the oods are not manufactured by the Company, are delivered direct to the Customer by, or collected by the Customer from the manufacturer, the Company shall not be liable for any loss or damage to the oods whatsoever and whensoever occurring. 6 ayment 6.1 The price for the oods including any charges for packaging, freight, insurance or any other charge whatsoever must be paid upon presentation of a pro-forma invoice and in any event prior to delivery. The Company reserves the right to refuse delivery if the price has not been so paid and shall not be liable for any loss caused to the Customer. 6.2 Where the Customer has been offered a credit account with the Company, unless other wise agreed, payment for the oods shall be made not later than the last day of the month following the month in which the oods were despatched from the Company's premises. The time stipulated for payment shall be of the essence and failure to pay within the period specified shall entitle the company on the expiration of 14 days notice in writing to the Customer to suspend further performance of the Contract pending payment and in addition the Company shall be entitled without liability wholly or partly to cancel the Contract or any other contract between the Company and the Customer without prejudice to any other remedy available to the Company. 6.3 Where oods are delivered by instalments, the Customer shall pay for each instalment in accordance with the terms of this Condition. 6.4 The Company shall be entitled to interest (as well before as after any judgment) any part of the Contract price not paid by its due date from that date until actual payment at the rate of 4% per annum above HSBC Bank plc's base lending rate prevailing from time to time during such period. 6.5 Unless otherwise agreed in writing the Customer shall not be entitled to set off against any monies due to the Company under the Contract, any amount claimed by or due to the Customer from the Company whether pursuant to the Contract or on any other account whatsoever. 6.6 Unless otherwise agreed in writing, all accounts shall be paid at the Company s registered office. Cheques and money orders shall be made payable to or to the order of the Company. Only the company s official receipt will be treated as valid. 7 roperty and Title to the oods 7.1 The oods shall be at the risk of the Customer from the time at which they are loaded on the vehicle on which they are to be delivered to the Customer whether such vehicle is the Customer's own vehicle or a third party's vehicle. 7.2 Notwithstanding section 7.1 the legal and beneficial ownership of the oods shall remain with the Company until such time as the Customer shall have paid to the Company in cash or cleared funds payment in full of the price of the oods and all other goods agreed to be sold by the Company to the Customer for which payment is due. 7.3 Until the title to and property in the oods pass to the Customer the following provisions shall apply: The Customer shall hold the oods solely as fiduciary agent and bailee for the Company and shall keep them separate from the Customer s own oods or those of any third party and in a manner which makes them readily identifiable as the oods of the Company The oods shall be properly stored, protected and insured and the Company shall be entitled to examine them in storage at any time during normal business hours and upon giving the Customer reasonable notice of its intention to do so and to enter upon any premises owned or occupied or access to which is controlled by the Customer for that purpose; The Company may at any time without prior notice to the Customer (and provided the oods are still in existence and have not been resold) repossess and resell the oods if any of the events specified in section 13 occurs or if any sum due from the Customer to the Company under the Contract or on any other account or pursuant to any other contract is not paid on the due date for payment. For the purpose of exercising its rights under this subparagraph the Company, its employees or agents together with any vehicles considered by the Company to be necessary shall be entitled at any time without prior notice to the Customer to free and unrestricted entry upon and access to the Customer's premises and/or other locations where any of the oods are situated. 7.4 Notwithstanding section 7.2 above the Customer may as principal in the ordinary course of business sell the oods by bona fide sale at full market value; in which case; the oods shall be deemed sold or used in the order delivered to the Customer any resale by the Customer of the oods in which property has not passed to the Customer shall (as between the Company and the Customer only) be treated as if made by the Customer as agent for the Company; the proceeds of sale of any oods shall be held by the Customer in trust for the Company to the extent of all sums recoverable by the Company under section 7.2 above; the Customer shall keep any proceeds of sale as referred to in section in a separate account and not mingled with other monies or paid into any overdrawn account and shall at all times be identifiable as the Company s money. In any event the Company shall have the right to trace such proceeds. 7.5 The Company may at any time appropriate to such indebtedness as it thinks fit sums received from the Customer notwithstanding any purported appropriation or designation by the Customer; 7.6 The rights and remedies conferred upon the Company by this section 7 are in addition to shall not in anyway prejudice, limit or restrict any other rights or remedies of the Company under the Contract. 8 elivery 8.1 ny date or time given by the Company to the Customer for the delivery of the oods is approximate only and it is not of the essence of the Contract and such failure shall not constitute a breach of contract by the Company entitling the Customer to terminate the Contract and/or to claim damages against the Company and the Company shall be entitled to an extension of the time fixed for delivery which is reasonable in all the cir cumstances. 8.2 The Company may deliver the roduct in advance of the quoted delivery date on giving reasonable notice to the Customer. 8.3 Where the company is to make separate deliveries under a single order or where 55

58 deliveries are to be made in instalments then failure to comply with any delivery date shall not be deemed to be a repudiation of the balance of the contract. 8.4 If the Company agrees that the Customer may collect the oods, the Customer shall collect them within 3 days of being notified that they are ready for collection failing which the Company may despatch the oods at the Customer's risk and expense or store them in which case the Customer shall pay the Company's reasonable storage charges and the oods shall be stored at the Customer's risk. It the Customer requests the Company to delay despatch of the oods and the Company agrees to do so the Customer shall pay the Company's reasonable storage charges and the oods shall be stored at the Customer's risk as from the date upon which the oods are ready for despatch. 8.5 If the Company arrives at the Customer's desired delivery site on the delivery date and on attending the site is unable to affect delivery of the roduct due to the Customer being unprepared or absent, or if the Customer fails to give the Company adequate delivery instructions at the time stated for delivery then, without limiting any other right or remedy available to the Company, the Company may store the roduct until actual delivery and charge the Customer for the reasonable costs (including insurance) of storage and redelivery. 9 Warranty and Liability Subject to the following provisions the Company warrants that the oods will correspond with their specification at the time of delivery and will be free from defects in material and workmanship. 9.1 The above warranty is given by the Company subject to the following conditions: the Company shall be under no liability in respect of any defect in the oods arising from any drawing, design or specification supplied by the Customer; the Company shall be under no liability in respect of any defect arising from fair wear and tear, wilful damage, negligence, abnormal working conditions, failure to follow the Company's instructions (whether oral or in Writing), misuse or alteration or repair of the oods without the Company's approval; the Company shall be under no liability under the above warranty (or any other warranty, condition or guarantee) if the total price for the oods has not been paid by the due date for payment; the above warranty does not extend to parts, materials or equipment not manufactured by the Company, in respect of which the Customer shall only be entitled to the benefit of any such warranty or guarantee as is given by the manufacturer to the Company. 9.2 Subject as expressly provided in these Conditions, and except where the oods are sold to a person dealing as a consumer (within the meaning of the Unfair Contract Terms ct 1977), all warranties, conditions or other terms implied by statute or common law are excluded to the fullest extent permitted by law. 9.3 Where the oods are sold under a consumer transaction (as defined by the Consumer Transactions (Restrictions on Statements) Order 1976) the statutory rights of the Customer are not affected by these Terms. 9.4 Subject to section 6, a claim by the Customer which is based on any defect in the quality or condition of the oods or their failure to correspond with specification shall (whether or not delivery is refused by the Customer) be notified to the Company within seven days from the date of delivery or (where the defect or failure was not apparent on reasonable inspection) within a reasonable time after discovery of the defect or failure. If delivery is not refused, and the Customer does not notify the Company accordingly, the Customer shall not be entitled to reject the oods and the Company shall have no liability for such defect or failure, and the Customer shall be bound to pay the price as if the oods had been delivered in accordance with the Contract. 9.5 Where a valid claim in respect of any of the oods which is based on a defect in the quality or condition of the oods or their failure to meet specification is notified to the Company in accordance with these Terms, the Company may replace the oods (or the part in question) free of charge or, at the Company's sole discretion, refund to the Customer the price of the oods (or a proportionate part of the price), in which case the Company shall have no further liability to the Customer. 9.6 Except in respect of death or personal injury caused by the Company's negligence, or liability for defective products under the Consumer rotection ct 1987, the Company shall not be liable to the Customer by reason of any representation (unless fraudulent), or any implied warranty, condition or other term, or any duty at common law, or under the express terms of the Contract, for loss of profit or for any indirect, special or consequential loss or damage, costs, expenses or other claims for compensation whatsoever (whether caused by the negligence of the Company, its employees or agents or otherwise) which arise out of or in connection with the supply of the oods (including any delay in supplying or any failure to supply the oods in accordance with the Contract or at all) or their use or resale by the Customer, and the entire liability of the Company under or in connection with the Contract shall not exceed the price of the oods, except as expressly provided in these Terms. 10 Force Majeure 10.1 The Company shall not be liable or be deemed to be in breach of these Conditions by reason of any delay in performing, or any failure to perform, any of the Company's obligations in relation to the oods, if the delay or failure was due to any cause beyond the Company's reasonable control. Without limiting the foregoing, the following shall be regarded as causes beyond the Company's reasonable control: ct of od, explosion, flood, tempest, fire or accident; war or threat of war, sabotage, insurrection, civil disturbance or requisition; acts, restrictions, regulations, bye-laws, prohibitions or measures of any kind on the part of any governmental, parliamentary or local authority; import or export regulations or embargoes; strikes, lock-outs or other industrial actions or trade disputes (whether involving employees of the Company or of a third party); difficulties in obtaining raw materials, labour, fuel, parts or machinery; power failure or breakdown in machinery. In the event of the foregoing the Company may suspend further performance of the Contract for so long as it is so delayed or prevented and such suspension shall not constitute a breach of the Contract on the part of the Company. The Company shall inform the Customer in writing of any such suspension of performance of the Contract and if such suspension continues for more than 12 weeks either the Company or the Customer may by notice in writing to the other terminate the Contract but without prejudice to the Company's right to be paid in accordance with the Contract for any part of the oods which may have been despatched to the Customer prior to the suspension of performance by the Company and to be reimbursed all other costs, charges and expenses incurred by the Company pursuant to the Contract up to the date of such notice of termination where it is given by the Company and up to the date of receipt thereof by the Company where it is given by the Customer. 11 Customers own esigns 11.1 The Customer shall be responsible for the accuracy of its own designs and drawings and other data supplied to the Company by the Customer its employees or agents notwith standing that the Company may have examined, inspected, studied or commented to the Customer upon any such designs, drawings, specifications or other data If the Company is required in connection with the manufacture of the oods to carry out any research or development work all intellectual property rights therein shall be the property of the Company and the Customer shall keep confidential all information disclosed by the Company to it concerning such research and development work and shall not exploit such information for its own purposes without the prior written consent of the Company provided that the foregoing provision shall not prevent the Customer from using the oods for whatever purpose it may think fit. 12 Intellectual roperty 12.1 The Customer warrants that any design or instruction furnished or given to the Company shall not be such as to cause the Company to infringe any letters patent registered designs or trade marks in the execution of the Customer s order. The Customer shall indemnify the Company against all claims actions and costs made or brought against the Company (whether in England or elsewhere) in respect of the infringement of any United Kingdom or foreign patent, trademark, trade name, registered design or similar right 13 Breach of Contract by or Insolvency of the Customer 13.1 If any of the following events occurs or in the opinion of the Company is reasonably likely to occur: the Customer commits any breach of the Contract; or any distress or execution is levied upon any of the oods or property of the Customer and is not paid out within 7 days; or the Customer (or where the Customer is a partnership any partner thereof) offers to make any arrangements with or for the benefit of its or his creditors generally or a petition is pre sented to make the Customer or any such partner bankrupt; or the Customer (being a limited company) has an dministrative Receiver or a Receiver and Manager appointed of the whole or any part of its undertaking property or assets or a petition is presented or an order is made or a resolution is passed for the winding up of the Customer or for the appointment of an dministrator thereof the Company may without prejudice to any other rights or remedies it may have against the Customer suspend further performance of the Contract or by notice in writing to the Customer terminate the Contract as it thinks fit. Notwithstanding any such suspension or termination, the Customer shall pay the Company in accordance with the Contract for all oods despatched by the Company up to that date and shall indemnify the Company against any loss, liability or expense incurred by the Company in connection with the Contract including (without prejudice to the generality of the foregoing) loss of profit, liabilities and expenses in connection with raw materials and tooling obtained or produced for the purposes of the Contract and the cost of labour and overhead expenses reasonably attributable to the Contract 14 Notices 14.1 ny notice to be given pursuant to these Conditions shall in the case of a notice to the Company be sent to it at its registered office and shall in the case of a notice to the Customer be sent to the Customer at its registered office if the Customer is a Company and in any other case to the address of the Customer last known to the Company. ny such notice may be given by post, telex or facsimile transmission. To prove service in the case of a notice given by post it shall be sufficient to show that the entice was despatched by first class recorded delivery service in a correctly addressed and adequately stamped envelope and to prove service in the case of a notice given by telex or facsimile trans mission it shall be sufficient to show that it was made to the correct telex or telephone number Service shall be deemed to have been effected 24 hours after despatch by post telex or facsimile transmission. 15 eneral 15.1 If any clause or sub-clause of these Conditions is held by any competent authority to be invalid or unenforceable in whole or in part, the validity of the other clauses or sub-claus es and the remainder of the provisions in question shall not be affected hereby The headings to these Conditions are inserted for ease of reference and shall not affect their construction The Company may subcontract any or all of its obligations hereunder without the prior consent of the Customer ny concession granted to the Customer by the Company or any waiver by the Company of its rights under these Conditions in respect of any particular transaction or series of transactions shall not be deemed an agreement to confer the same concessions in respect of any further transactions This contract shall not bestow any rights on any third parties and to this end the Contracts (Rights of third arties) ct 1999 is excluded to the fullest extent possible The law applicable to this contract is English law and the Customer and the Company hereby submit to the exclusive jurisdiction of the Courts of England and Wales. 56

59 cod. CYNW. E305934