CENTRUM CUP STACKER OPERATIONAL INSTRUCTIONS

Transcription

1 TM CENTRUM CUP STACKER OPERATIONAL INSTRUCTIONS Ensure that all personnel read the points listed within this leaflet and that a copy is given to staff involved with the installation and maintenance of this product. Glasdon recommends that a full Health and Safety analysis is carried out prior to installation. CENTRUM CUP STACKER COMPONENTS: ITEM 1 - Cup Stacker Bracket ITEM 2 - Cup Tube ITEM 3 - Quick Release Mechanism ITEM - Drip Tray ITEM 5 - Drip Tray Bracket EMPTYING THE CUP TUBE / DRIP TRAY To transport the Cup Tube, lift the tube off the Cup Stacker Bracket. Using the Stainless Steel ring, open the Quick Release Mechanism to remove cups. To empty or clean the Drip Tray, remove the Drip Tray from the Drip Tray Bracket. 1 of 6

2 CENTRUM TM CUP STACKER WALL FIXING INSTALLATION MANUAL Ensure that all personnel read the points listed within this leaflet and that a copy is given to staff involved with the installation and maintenance of this product. Glasdon recommends that a full Health and Safety analysis is carried out prior to installation. Instructions are for fixing the product to a masonry wall. Other wall types should be assessed for the most appropriate permanent fixing method. FIXING POINT GUIDE ALL MEASUREMENTS IN MM SHADED GREY AREAS REPRESENT THE TWO BRACKETS. 5 CRs INSTALLATION GUIDE KIT CONTENTS: ITEM 1 - Cup Stacker Bracket x 1 ITEM 2 - Brown Wall Plug x 8 ITEM Wood Screw x 8 ITEM - Drip Tray Bracket x 1 ITEM 5 - Cup Tube x 1 ITEM 6 - Drip Tray x 1 EQUIPMENT REQUIRED: - Pencil - Tape Measure - Hand Drill with 7mm drill bit - Hammer - Phillips Head Screwdriver CRS 781CRS * 92CRS *THE DRIP TRAY BRACKET SHOULD BE INSTALLED 00mm FROM GROUND LEVEL 6 2 of 6

3 mm Using the Fixing Point Guide as a reference, measure 1183mm from the ground level and mark with the pencil. Align the base of ITEM 1 with the line against the wall and mark the hole positions. Drill the marked points with the Hand Drill. Repeat steps 1&2 for the Drip Tray Bracket holes. There should be 656mm between the base of ITEM 1 and the top of ITEM. Push 8 x ITEM 2 into the 8 drilled holes. Tap the plugs lightly with the Hammer to ensure they are flush with the wall surface. 5 6 Place the Cup Stacker Bracket against the top fixings holes and thread through ITEM 3. Tighten the Screw with the Screwdriver and repeat for all fixings points securing the Cup Stacker Bracket to the wall. Place ITEM against the wall aligning the holes with the wall plugs, Thread through one of the SCREWS and tighten with the Screwdriver. 7 8 Repeat step 6 for all fixing points securing the Drip Tray Bracket to the wall. Place ITEM 5 onto the Cup Stacker Bracket and place ITEM 6 onto the Drip Tray Bracket. 3 of 6

4 CENTRUM TM CUP STACKER A SIGN KIT WALL FIXING INSTALLATION MANUAL Ensure that all personnel read the points listed within this leaflet and that a copy is given to staff involved with the installation and maintenance of this product. Glasdon recommends that a full Health and Safety analysis is carried out prior to installation. Instructions are for fixing the product to a masonry wall. Other wall types should be assessed for the most appropriate permanent fixing method. INSTALLATION GUIDE KIT CONTENTS: ITEM 1 - A Foamex Sign x 1 ITEM 2 - Red Wall Plug x ITEM Wood Screw x ITEM - Screw Cover Cap x ITEM 5 - Cup Stacker (Installed) x 1 EQUIPMENT REQUIRED: - Tape Measure - Pencil - Hand Drill with 5mm drill bit - Hammer - Phillips Head Screwdriver of 6

5 mm The sign should be positioned 60mm above the top of the Cup Stacker. Place ITEM 1 against the wall 60mm above the top of ITEM 5. Mark fixing points on the wall through the holes in the A Foamex Sign, ensure the sign is horizontal and centrally straight. Drill the marked points with the hand drill. 5 6 Push x ITEM 2 into the drilled holes. Tap the plugs lightly with the Hammer to ensure they are flush with the wall surface. 7 Place ITEM 3 through ITEM. Place the A Foamex Sign against the fixings holes and thread one of the Screw fixings into the wall plug. Fit all fixings, using the Screwdriver to tighten. Close the screw covers when complete. 5 of 6

6 , CENTRUM AND NEXUS ARE TRADEMARKS OR REGISTERED TRADEMARKS OF GLASDON GROUP OR ITS SUBSIDIARIES IN THE U.K. AND OTHER COUNTRIES A planned maintenance schedule or regular inspection is recommended, replacing components as necessary. Replacement components are available direct from GLASDON. GLASDON cannot be held responsible for claims arising from incorrect installation, unauthorised modifications or misuse. of the product. Issue 3 - October Stock No. C000/ DWG No. 07B Copyright October 2017 Glasdon UK Ltd reserve the right to alter specifications without prior notice. Glasdon U.K. Limited Preston New Road BLACKPOOL Lancashire FY UL Tel: (01253) Fax: (01253) sales@glasdon-uk.co.uk web: 6 of 6