2.54mm Pitch Board to Cable Connector
|
|
|
- Doris Jordan
- 6 years ago
- Views:
Transcription
1 2.54mm Pitch Board to Cable Connector FRC5 Series Conforming Standard MIL-DTL-8353 FETURE UL pproved (File No. E72124) Conform to MIL-DTL-8353 Polarizing key prevents from mis-mating. SPECIFICTIONS Rated Voltage Rated Current Insulation Resistance Resistance Dielectric Withstanding Voltage 25V C (r.m.s.) 1 / 1 MΩ min. at 5V DC 15 m Ω max. 5V C (r.m.s) / 1 minute Operating Temperature pplicable Cable WG28 (Stranded Cable / Solid Cable) WG3 (Solid Cable) MTERIL/FINISH Socket Item Material / Finish Housing PBT Resin(UL94V-) / Black Cover PBT Resin(UL94V-) / Black Copper lloy / u over Ni Plating Strain Relief PBT Resin (UL94V-) / Black Header Item Material / Finish Housing PBT Resin (UL94V-) / Black Copper lloy / u over Ni Plating Lock Lever PBT Resin (UL94V-) / Black Spring Pin Stainless Steel 1412
2 Socket Connector FRC5-26-3TS-F Cover Style :Open-end :Closed-end Note)Closed-end cover for 64 contacts are not available 1, 14, 16, 2, 26, 3, 34, 4, 5, 6,64 Plating 1:u (.8 μ m) over Ni Plating 2:u (.4 μ m) over Ni Plating 3:u (Flash) over Ni Plating Plating (Termination rea) T:Sn-g Plating F:Lead Free Strain Relief N:without Strain Relief S:with Strain Relief :1 No Key 14, 16, 2, 26, 3, 34, 4 1 Key 5, 6, 64 2 Keys (H=22.86mm) :5, 6, 64 1 Key C:6, 64 2 Keys (H=27.94mm) D : 1 1 Key Part Number Number of B Cover Strain Relief FRC5-X1-XXXX-F FRC5-X14-XXXX-F Plating Sign Marking T 5 B FRC5-X16-XXXX-F FRC5-X2-XXXX-F FRC5-X26-XXXX-F FRC5-X3-XXXX-F FRC5-X34-XXXX-F FRC5-X4-XXXX-F FRC5-X5-XXXX-F FRC5-X6-XXXX-F FRC5-X64-XXXX-F FRC5-x26~x4-xxxx-F FRC5-x5~x64-xxx-F 5-1T Sign C 5-1T FRC5-x1-xxx-F FRC5-x1-xxDx-F FRC5-x14-xxx-F FRC5-x16-xxx-F FRC5-x2-xxx-F H FRC5-x5~x64-xxx-F FRC5-x6-xxCx-xxCx-F
3 Cover, Strain Relief Open-end Cover FRC Closed-end Cover FRC Inspection Hole Less than 16 s:1 More than 2 s: Part Number Number of FRC2-1-XX FRC2-14-XX FRC2-16-XX FRC2-2-XX FRC2-26-XX FRC2-3-XX FRC2-34-XX FRC2-4-XX FRC2-5-XX FRC2-6-XX FRC2-64-XX Note:Cloosed-end cover for 64 contacts are not available Strain Relief FRC
4 Header Connector FRC5-C26L51T-L-F 1, 14, 16, 2, 26, 3, 34, 4, 5, 6, 64 F:Lead Free Style L:Right ngle S:Straight Lock Lever L:Long Lock S:Short Lock Tail Length 4: G=3.94 5: G=2.9 (Standard) Plating 1:u(.8 μ ) over Ni Plating 2:u(.4 μ ) over Ni Plating 3:u(Flash) over Ni Plating Plating Termination rea) T:Sn-g Plating :1 No Key 14, 16, 2, 26, 3, 34, 4 1 Key 5, 6, 64 2 Keys (H=22.86mm) :5, 6, 64 1 Key C:6, 64 2 Key (H=27.94mm) D:1 1 Key (E) (E) D C X.64.5 J J G Sec. X-X FRC5-CXXLXXX-XX-F G.64.5 Sec. X-X FRC5-CXXSXXX-XX-F Header with Short Lock φ.75 max. 3.4 B X Section Header without Lock Lever 2 C1 2 C1 2 C14 2 C F FRC5-C1XXXX-X-F FRC5-C1XXXX-DX-F FRC5-C14XXXX-X-F FRC5-C16XXXX-X-F 2 C Sign C34 2 C C Lot No. Y Y Marking H Marking FRC5-C2~C3XXXX-X-F Tail Style/Plating FRC5-C34~C4XXXX-X-F FRC5-C5~C64XXXX-X-F FRC5-C5~C64XXXX-X-F FRC5-C6XXXX-CX-F 3 Tapping Number Long Lock Short Lock Part Number of B C D F E J E J FRC5-C1XXXX-XX-F FRC5-C14XXXX-XX-F FRC5-C16XXXX-XX-F FRC5-C2XXXX-XX-F FRC5-C26XXXX-XX-F FRC5-C3XXXX-XX-F FRC5-C34XXXX-XX-F FRC5-C4XXXX-XX-F FRC5-C5XXXX-XX-F FRC5-C6XXXX-XX-F FRC5-C64XXXX-XX-F ±.1 (Nominal Diameter.74±.1 4 注 1.25±.1
5 .74±.1.9 FRC5 Series Header Connector.74±.1.9 Recommended PCB Mounting Dimensions (Soldering Side).74±.1 C±.12 C±.12 B±.15 B±.15.9 Right ngle Right ngle 注 1 C±.12 B±.15 Right ngle 注 1 注 C±.12 C±.12 F±.15 F±.15 Straight Straight C±.12 F±.15 Straight.25± ±.1 (Nominal Diameter 3 Tapping Screw) 3.2 ± ±.1 (Nominal (Nominal Diameter 3 Diameter Tapping 3 Screw) Tapping Screw) 1 When using M2.6 screw, the hole diameter should be 2.8. When using nominal diameter 3 tapping screw, the hole diameter should be ±.1.25± Long Lock (FRC2-1) Short Lock (FRC2-2) Spring pin (FRC-3) ssembly Tool(357J-452) ssemble/disassemble the lock lever for Socket Part Number:HU-5 HU-5 consists HU-5-1 ND HU-5-2. Material / Finish : Polyamide (UL94V-) / Natural Color HU-5-1 HU-5-2 Key Guide for Header HU-5-1 HU-5-2 Part Number :HU-6 HU-5-1 Material / Finish : Polycarbonate (UL94V-) / Black HU-5-2 When connectors having same number of contacts are used side by side, key guide can prevent from mis-mating. 1(No key)and16 contacts are not applicable. HU-6 HU-6 FRC-1 FRC-1 5
6 Cable ssembly Configurations Cable No. and Position ssembly Tool Cable Cutting Tool :357J-4256 Termination Tool :357J-4674D(Press) :357J-4664N(ttachment) 6
Solutions for Electronic Specialty Markets (ESM)
M Worldwide : United States : Electronics Manufacturing Solutions for Electronic Specialty Markets (ESM) Product Catalog for Electronic Specialty Markets M Electronic Specialty Markets - New Product Releases
0.2 mm Pitch Back-Lock FPC Connector
0.2 mm Pitch Back-Lock FPC Connector FFX2 Series OUTLINE FFX2 series is a FPC connector which is 0.2mm contact pitch and 0.95mm heiht. pplicable FPC is 0.12mm thickness and 0.4mm pitch conductors on both
3M Eurosocket Type C (Rows A & C or A, B & C Filled)
DIN 41612 compatible High density (64 & 96 position) Mates with DIN 41612 Type C headers High reliability contact design Can be daisy-chained or end terminated to flat cable Optional strain relief with
3M Pak Wall Header
M Pak 100 4-Wall Header.100.100 Latch/Ejector, Straight and Right ngle, High Temp Option 000 Series S Military (with M s 518 polarizing key) and centerbump polarization S Optional ejector latches S Mounting
3M Eurosocket Type C (Rows A & C, A & B or A, B & C Filled)
DIN 41612 compatible High density (64 & 96 position) Mates with DIN 41612 Type C headers High reliability contact design Can be daisy-chained or end terminated to flat cable Optional strain relief with
3M Eurosocket Type C (Rows A & C, A & B or A, B & C Filled)
DIN 41612 compatible High density (64 & 96 position) Mates with DIN 41612 Type C headers High reliability contact design Can be daisy-chained or end terminated to flat cable Optional strain relief with
Cannon Trident Connector System
These are low installed cost connectors rated for up to 13 A and 250 V ac. They are typically used for circuit board and internal wiring applications. Snap Together connectors facilitate easy assembly
3M Three-Wall Header Latch/Ejector, Straight and Right Angle 3000 Series
M Three-Wall Header.100.100 Latch/Ejector, Straight and Right ngle 000 Series Military (with M s 518 or N518 polarizing key) and center bump polarization Low profile Optional ejector latches Mounting holes
HS h e n EU omplia t 2002 / 9 5 / C
9 57-30500 0 0 E U 2 C A mp hen 2/ 5 / E omplia Ro HS ol C nt hen z n She 57-30360 DE-09P & DE-09S Standards: UL File: E119881 Connectors according to MIL C24308 SPECIFICATIONS : MATERIALS AND Shells Steel
Ribbon Cable connector Compliant with MIL Standard
Ribbon Cable connector Compliant with MIL Standard HIF3B Series Features 1. Product Compliant with MIL Standard HIF3B series has been developed as a product compliant with MIL standard, and used for wide
3M Four-Wall Header Latch/Ejector, Straight and Right Angle 3000 Series
M Four-Wall Header.100.100 Latch/Ejector, Straight and Right ngle 000 Series Military (with M s 518 & N518 polarizing key) and centerbump polarization Optional ejector latches Mounting holes for securing
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. .100.100 Latch/Ejector, Straight and Right ngle 3000 Series Military (with
3M 4-Wall Header Low Profile, SMT Straight, Straight and Right Angle Thru Hole2500 Series
M 4-Wall Header.100.100 Low Profile, SMT Straight, Straight and Right ngle Thru Hole2500 Series Low profile, space saving design Center slot polarization prevents mis-insertions and reduces insertion time
3M HDC Header. Physical. Electrical. Environmental Vertical Mount, PCB/Backplane, Solder Tail or Press-Fit HDC Series
M HDC Header High density, up to 240 contacts single bay Early Mate Late Break (EMLB) grounding contacts for hot swapping Mates with three-row and four-row sockets RoHS* compliant. See the Regulatory Information
3M Three-Wall Header Latch/Ejector, Straight and Right Angle 3000 Series
M Three-Wall Header.100.100 Latch/Ejector, Straight and Right ngle 000 Series Military (with M's 518 or N518 polarizing key) and center bump polarization Low profile Optional ejector latches Mounting holes
3M Four-Wall Header Latch/Ejector, Straight and Right Angle 3000 Series
M Four-Wall Header.100.100 Latch/Ejector, Straight and Right ngle 000 Series Military (with M's 518 & N518 polarizing key) and centerbump polarization Optional ejector latches Mounting holes for securing
3M D Sub Socket 50 Position 8350 Series
M D Sub Socket 50 Position 850 Series IDC compatible Lower insertion/withdrawal force than other 50 position products Available in either open or closed end cover Mounting options include #4-40 UNC or
3M Mini D Ribbon (MDR) Connectors.050 Boardmount Through-Hole Right Angle Plug - Shielded 101 Series
Boardmount Through-Hole Right ngle Plug - Shielded 101 Series Wiper-on-wiper contact for reliable repetitive plugging Rugged die cast metal case construction Screw or ground lock PCB retention Normal and
3M Pak Wall Header Latch/Ejector, Straight and Right Angle 3000 Series
Pak 100 4-Wall Header.100.100 Latch/Ejector, Straight and Right ngle 3000 Series Military (with 's 3518 polarizing key) and centerbump polarization Standard ejector latches Mounting holes for securing
3M Shielded Compact Ribbon (SCR) Connectors Boardmount Right Angle Plug
M Shielded Compact Ribbon (SCR) Connectors Boardmount Right Angle Plug 61 Series Robust ribbon style contact for reliable, repetitive plugging Body tabs provide lateral support to solder joints and help
Latch/Ejector, Straight and Right Angle 3000 Series
Military (with M s 518 & N518 polarizing key) and centerbump polarization Optional ejector latches Mounting holes for securing header to board Optional polarizing posts available High temperature insulator
3M Four-Wall Header.100".100" Latch/Ejector, Straight and Right Angle 3000 Series
M Four-Wall Header.100".100" Latch/Ejector, Straight and Right ngle 000 Series Military (with M s 518 & N518 polarizing key) and centerbump polarization Optional ejector latches Mounting holes for securing
Amphenol Amphenol Taiwan Corporation Sheet 1 of 7
Amphenol Amphenol Taiwan Corporation Sheet 1 of 7 Title: Part Number: Description: Micro SD Card Connectors Product Specification GTFP08 SERIES Micro SD Card Connectors push-push type Revisions Control
3M 4-Wall Header Latch/Ejector, Straight and Right Angle 3000 Series
Military (with 's 3518 polarizing key) and centerbump polarization Standard ejector latches Mounting holes for securing header to board RoHS* compliant Optional polarizing posts High temperature insulator
3M Molded Socket for.050 Pitch Cable, Cable Assembly Connector 871 Series
3M Molded Socket.100.100 for.050 Pitch Cable, Cable Assembly Connector 871 Series Part of a complete cable assembly Mates with industry standard 0.025 inch square contacts on.100 inch x.100 inch centers
Distributed by: www.jameco.com 1-800-81-4242 The content and copyrights of the attached material are the property of its owner. M Wiremount Socket.100.100 for.050 Pitch Cable 891 Series Preassembled, terminates
Card Edge Type Ribbon Cable Connectors
Card Edge Type Ribbon Cable Connectors HIF5 Series Product Specifications Rating 1. Insulation Resistance 1000M min. 2. Withstanding voltage No flashover or insulation breakdown. 3. Contact Resistance
FEMALE SOCKET CONNECTORS
PRODUCT DESCRIPTION The Thomas & Betts Female Socket Connectors are designed to mate with a wide variety of Male Headers in PC board applications which require repeated connection and disconnection. The
Distributed by: www.jameco.com 1-800-81-4242 The content and copyrights of the attached material are the property of its owner. M Four-Wall Header Low Profile, SMT Straight, Straight and Rt ngle Through-Hole
Physical. Electrical. Environmental. Insulation: Contact: Plating: Marking: 3M Logo, Part Identification Number and Orientation Triangle
3M Polarized Boardmount Socket.100.100 Centerbump Polarization with Right Angle Solder Tails 5100 Series Centerbump polarization Mates with standard low profile shrouded headers Part number on each piece
NARROW PITCH (0.4mm) CONNECTORS P4S SERIES
FOR BOARD-TO-BOARD AND BOARD-TO-FPC CONNECTION AXT3, 4 NARROW PITCH (0.4mm) CONNECTORS P4S SERIES NEW 2. Strong resistance to adverse environments! Utilizes construction for high contact reliability. 1)
Features. FX22 Series NEW
NEW FX22 Series Floating range: ±.6mm Z X Fig.1 Features 1. The floating design Structure provides for an mis-alignment of ±.6mm in both X and Z directions in.5mm pitch product. (Fig.1) 2. A double-beam
Series 805 Mighty Mouse Triple-Start ACME Thread Receptacle
Series 0 Mighty Mouse Triple-Start ACME Thread Receptacle 0-00 and 0-00 Ordering Information Series 0 Three Shell Mounting Options: Jam nut with O-ring for rear panel mounting, square flange for front
PLCC Sockets Through Hole - M43 Series
Through Hole - M43 Series PART NUMBER LEGEND M43X-XX-XX NUMBER OF CONTACTS 20, 28, 32, 44, 52, 68, 84, 100 (-10 Style) 44, 52, 68, 84 (-11 Style) STYLE -10 Standard wall thickness, through hole -11 Thin
3M Mini D Ribbon (MDR) Connectors.050 Boardmount Through-Hole Right Angle Receptacle - Shielded 102 Series
M Mini D Ribbon (MDR) Connectors.050 Boardmount Through-Hole Right Angle Receptacle - Shielded 102 Series Wiper-on-wiper contact for reliable repetitive plugging Surface mount compatible PCT insulator
3M Wiremount Socket Position for.050 Pitch Cable 79 Series
3M Wiremount Socket.100.100 64 Position for.050 Pitch Cable 79 Series Standard profile plastic strain relief Mates with 3M headers, plugs, and pin strips for quick connect/disconnect capability Centerbump
D-SUBMINIATURE DESCRIPTION/APPLICATION DESIGN ADVANTAGES D-SUB INDEX. IDC Systems D-Subminiature
DESCRIPTION/APPLICATION Fine Pitch D-Sub Connectors are designed for reliable interfaces in modern, high-density applications. Conforms with SCSI 2/3 internal cabling specification. The low-profile design
3M Pin Strip Header 2 mm and 2 mm x 2 mm Straight, Surface Mount 951 Series
3M Pin Strip Header 2 mm and 2 mm x 2 mm Straight, Surface Mount 951 Series High temperature dielectric No lead reflow solder compatible Maximizes use of PC board space End stackable feature Mates with
3.96 mm Pitch Miniature Connectors for Internal Power Supplies (UL,C-UL and TÜV Listed)
ll non-rohs products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales
Contents B Description
Contents Description Page CONTACT TECHNOLOGY 1-12 General Technical Specifications 1 CLIPS 4 Printed Circuit Pins, Pin Connectors 5 Pin Receptacles, Sockets Contacts 8 DUAL-IN-LNE Sockets & PGA Sockets
4.5 mm pitch, Horizontal Mating 2-Piece System Connectors
NW 4.5 mm pitch, Horizontal Mating 2-Piece System Connectors D64 Series (UL pending) The floating structure of the BTB connection provides increased flexibility by absorbing the movement of the PCB s.
3M Mini D Ribbon (MDR) Connectors.050 Boardmount Thru-Hole Right Angle Receptacle-Shielded 102 Series
3M Mini D Ribbon (MDR) Connectors.050 Boardmount Thru-Hole Right ngle Receptacle-Shielded 102 Series Wiper-on-wiper contact for reliable repetitive plugging Rugged die cast metal case construction SMT
PIN Sockets & PIN Connectors General Specifications Part Numbers And Product Identification
Sockets & Connectors General Specifications Part Numbers And Product Identification GENERAL SPECIFICATIONS The values listed below are general specs applying for LEYCONN socket and pin connectors. Please
0.35mm Pitch 0.8mm Height Hybrid Power/Signal Connectors for Board-to-Board and FPC-to-Board
NEW.35mm Pitch.8mm Height Hybrid Power/Signal Connectors for Board-to-Board and FPC-to-Board BM24 Series Conventional type (P=.35 mm, 2 contacts) Features 1 Rated current : 5A The compact BM24 Series features
2 2.2mm Pitch, Wire-to-Wire Connectors for Small Spaces
2 2.2mm Pitch, Wire-to-Wire Connectors for Small Spaces DF62 Series / DF62W Series Features 1. The slim, sleek design and smooth contour combine to complete connections in tight spaces. These connectors
Card Edge Type Ribbon Cable Connector
Card Edge Type Ribbon Cable Connector HIF5 Series pplications Computers, FDD, various kinds of electronic equipment. Features 1. Product Variation The area to install the connector body is classified into
Physical. Electrical. Environmental. Insulation: Contact: Plating: Shroud: Temperature Rating: -55 C to +85 C
M I/O Interconnect System 2.0 mm for IEEE 194 Right Angle, Horizontal, Through-Hole Plug (Male) E106 Series Robust ribbon style contact for reliable, repetitive plugging Body tabs provide lateral support
NARROW PITCH (0.4mm) CONNECTORS P4S SERIES
FOR BOARD-TO-BOARD AND BOARD-TO-FPC CONNECTION NARROW PITCH (0.4mm) CONNECTORS P4S SERIES Compliance with RoHS Directive http://www.mew.co.jp/ac/e/ FEATURES 1. Space saving Compared to the currently sold
3M MetPak 2-FB Socket
M MetPak 2-FB Socket End-to-end stackable Offset dual-beam contact minimizes insertion force Molded guide fingers provide integrated alignment Alignment wafer for true position Mates with MP2-P inverse
VMiniature Basic Switch
that Offers High Reliability and Security Wide variation of best-selling microswitches with switching currents of 10 to 21. Can be used for interrupting current when doors are opened or closed. vailable
3M Interconnect Products
3M Interconnect Products Molded-On Cable Assembles www.ttiinc.com T h e NWeo rvl d e s r L e as d ihn g o Pr a t s s i vo e n & C So non el c ut o tr is po e cn i as l i s t 3M Molded-On Cable Assemblies
3M Link Connector.100" Boardmount, Straight and Right Angle 382 Series
3M Link Connector.100" Boardmount, Straight and Right Angle 382 Series Mates with 3M Wiremount Link Connector 38104 Vertical or right angle configuration Accepts latch mechanism of Wiremount Link Connector
3M Card Connector SD Normal Polarization, Push-Push, Surfacemount SD Series
M Card Connector SD Low profile, light weight, and small size Compatibility with both SD card and multimedia card formats Smooth push push eject mechanism protect switch indicator Card polarization Card
3M Mini D Ribbon (MDR) Connectors.050 Surface Mount Right Angle Receptacle - Shielded 102 Series
3M Mini D Ribbon (MDR) Connectors.050 Surface Mount Right Angle Receptacle - Shielded 102 Series Wiper-on-wiper contact for reliable repetitive plugging Ultra-low signal skew for high data rate transmission
N-Series: High-Temperature Connectors
N-Series: High-Temperature Connectors DIMENSIONS NMHT I/O Cable (Male) NMHT interconnects are used in hightemperature applications. These rugged cable connectors come with a variety of termination, hardware
Contacts for Full Duplex Ethernet Link
8D Series Twinax & Quadrax Contacts Contacts for Full Duplex Ethernet Link Twinax and Quadrax contacts with robust MIL-DTL-38999 compliant screw coupling system for networks and high vibration environments.
ORDERING INFORMATION: P/N K S 5 E U x CAT. 5e TOOLLESS RJ45 KEYSTONE JACKS (UNSHIELDED) P111
CAT. 5e TOOLLESS RJ45 KEYSTONE JACKS (UNSHIELDED) Insulation Resistance: 500M ohms (min.) Contact Resistance: 20m ohms (max.) Current Rating: 1.5 Amps. DC Resistance: 0.1 ohm (max.) Withstanding Voltage:
Floating Stacking 0.5mm Pitch Board to Board Connector
Floating Stacking 0.5mm Pitch Board to Board Connector FX20 Series X direction Floating range : 0.6 to 0.8mm Y direction Floating range : 0.6mm Features 1. 0.5mm pitch 2. Connection type: Stacking 3. Number
3M MetPak 2-FB Socket 2 mm 4/5-Row, Solder Tail or Press-Fit With Tail Cover, Right Angle MP2 Series
M MetPak 2-FB Socket End-to-end stackable Offset dual-beam contact minimizes insertion force Expanded pin counts Protective Push-Cap Monoblockable Press or heat stake peg 12 mm modular units Meets global
Physical. Electrical. Environmental
M MetPak 2-FB Inverse Header 2 mm 5-Row, Right Angle, Solder MP2 Series Three levels of early mate, late break (EMLB) sequencing or selective loading options Footprint compatible with standard Futurebus+
Extended-Frequency SMA Connectors
Extended-Frequency SM Connectors Extended-Frequency SM Connectors This brochure introduces two new series of connectors that extend SM performance beyond the MIL-PRF-39012 upper frequency limit of 18 GHz,
DISCONTINUED. Replaced by
M DIN R-Form Plug Inverse Mount, Vertical, Solder Tail or Press-Fit Termination DIN 41612 Series Early mate late break (EMLB) grounding contacts for hot swapping Select load capability Expanded pin counts
DISCONTINUED. 3M PC Card Header Single Slot, No Ejector. Physical. Electrical. Environmental. UL File No.: E68080
M PC Card Header Meets PCMCIA specifications Tapered header pins provide easy insertion High temperature plastic insulator Solder retention clips option for secure hold-down Stand-off height options ESD
Features. FX22 Series
FX22 Series Floating range: ±.6mm Z X Features 1. The floating design Structure provides for an mis-alignment of ±.6mm in both X and Z directions in.5mm pitch product. (Fig.1) 2. A double-beam contact
High Speed, Matched-Impedance, Parallel Board-to-board Connector System
High Speed, Matched-Impedance, Parallel Board-to-board Connector System IT Series Receptacle (2 required) IT Series Outline High-speed matched-impedance parallel board-to-board connector designed for applications
3M Pin Strip Header 2 mm 2 mm Solder Tail Straight & Right Angle, Surface Mount Straight 1512 Series
M Pin Strip Header Industry standard compatible High temperature dielectric "No lead" wave and reflow solder compatible Unique lengths available Maximizes use of PC board space Mates with boardmount and
3M PCB Connector.100 Four Row 3400 Series
PCB Connector.00 Four Row 300 Series Low profile Standard staggered grid Variety of pin lengths and plating options available See Regulatory Information Appendix (RIA) for chemical compliance information
DISCONTINUED. 3M PC Card Header Dual Slot, Low Profile, Integrated Ejector. Physical. Electrical. Environmental. UL File No.
PC Card Header Meets PCMCIA specifications Tapered header pins provide easy insertion High temperature plastic insulator Left or right ejector options ESD clips and plastic pegs for secure hold-down See
3M Mini D Ribbon (MDR) Connectors.050 Boardmount Through-Hole R. A. Condo Receptacle - Shielded 102 Series
M Mini D Ribbon (MDR) Connectors.050 oardmount Through-Hole R. A. Condo Receptacle - Shielded 102 Series Wiper-on-wiper contact for reliable repetitive plugging Rugged die cast metal case construction
Connector Selection Guide
Connector Selection Guide my.rs-online.com (Malaysia) www.rs-components.com (International) International Thermocouple Colour Codes for Connector Bodies All THERMOCOUPLE connectors use true thermocouple
3M MetPak HSHM Press-Fit Header 2 mm Type B25, 125 Signal Contacts, 5 Rows, Straight HSHM Series
M MetPak HSHM Press-Fit Header Up to 5 Gb/s data rates Low crosstalk at high frequencies 50/100 Ω (single-ended /differential) impedance Modular/scalable format IEC 61076-4-101 6 mated lines per linear
3M MetPak HSHM Press-Fit Header 2 mm Type B19, 95 Signal Contacts, 5 Rows, Straight HSHM Series
M MetPak HSHM Press-Fit Header Up to 5 Gb/s data rates Low crosstalk at high frequencies 50/100 Ω (single-ended /differential) impedance Modular/scalable format IEC 61076-4-101 6 mated lines per linear
3M CF Card Header CompactFlash Type I, Surface Mount
CF Card Header Meets CF standards Single row solder tails with 0.635 mm spacing Board component clearance with 1.64 mm standoff Ejector option for easy removal of CF Card Retainer clip option permits stability
DTS-HC High-Current Connectors
ROBUST DTS-HC High-Current Connectors Signal and power contacts in same housing Up to four 150 A or one 300 A high-current contacts Threaded coupling with self-locking mechanism for anti-vibration 100%
Photo. JBX Push Pull Sealed IP68 (Mated) The Solution for both Outdoor and Indoor waterproof applications. Secure for Outdoor applications.
Photo Environmentally Integrated Backshell Sealed Fire JBX proof onnector The Solution for both Outdoor and Indoor waterproof applications Secure for Outdoor applications Waterproof, IP68 (Mated) Reliable
Amphenol PT, SP, MS/PT Proprietary/MIL-C-26482, Series 1 solder type
Amphenol PT, SP, MS/PT Proprietary/MIL-C-26482, Series 1 solder type Amphenol solder contact miniature cylindrical connectors meet the most critical application needs. esign versatility combined with high
36,50 21,50. RJ45, CAT6a FEEDTHROUGH CONNECTOR GROUNDED TO OUTER SHELL DATA TRANSFER RATE TESTED TO 10 GIGABIT, CONTACT SALES OFFICE FOR TEST RESULTS
29,36 TYPICAL 26,98 TYPICAL 2,50 M28x - 6g TO SUIT H INTERFACE 4,93,250-0,P-0,3L-TS 3,25, CAT6a FEEDTHROUGH CONNECTOR GROUNDED TO OUTER SHELL DATA TRANSFER RATE TESTED TO 0 GIGABIT, CONTACT OFFICE FOR
solutions HIGH DENSITY CONNECTORS Custom designed Contact arrangements
Custom designed HIGH DENSITY CONNECTORS NANO-D PITCH As the need for increased miniaturisation is becoming ever greater, AXON has developed an ultra-high density solution within the existing micro connector
Amphenol Amphenol Taiwan Corporation Sheet 1 of 8
Amphenol Amphenol Taiwan Corporation Sheet 1 of 8 Title: Part Number: Description: Micro Power Plus Product Specification G88MP Series 3.0 mm Pitch, PCB Mount / Cable Crimping Type Revisions Control Rev.
Overall Length
CABLE DRAWING: POSEIDON SCIENTIFIC INSTRUMENTS PTY LTD 17 QUEEN VICTORIA ST, FREMANTLE WA 6160. PHONE (08) 9430 6639 FAX (08) 9335 4650 MWA-3004 DRAWING TITLE: ASC2 to SBC(ASC2) I2C Control Cable DRAWING
3M Pin Strip Header 2 mm 2 mm Solder Tail Straight & Right Angle, Surface Mount Straight 1512 Series
M Pin Strip Header Mates with a variety of dual row 2 board mount and wire mount sockets High temperature insulator compatible with lead-free solder processes Extensive pin count availability from 4 to
3M CF Card Header CompactFlash Type I, Surface Mount
Meets CFA standards Single row solder tails with 0.65 mm spacing Board component clearance with 1.64 mm standoff Ejector option for easy removal of CF Card Retainer clip option permits stability for mobile
3M CF Card Header CompactFlash Type I, Surface Mount
Meets CFA standards Single row solder tails with 0.635 mm spacing Board component clearance with 1.64 mm standoff Ejector option for easy removal of CF Card Retainer clip option permits stability for mobile
DISCONTINUED. 3M PC Card Header Single Slot, Low Profile, Integrated Ejector. Physical. Electrical. Environmental. UL File No.
3M PC Card Header Single Slot, Low Profile, Integrated Ejector MCH Series Meets PCMCIA specifications Tapered header pins provide easy insertion High temperature plastic insulator Left or right ejector
Amphenol Amphenol Taiwan Corporation Sheet 1 of 9
Amphenol Amphenol Taiwan Corporation Sheet 1 of 9 Title: Part Number: Description: USB3.1 Connector Product Specification GSB4X series A / B type, Receptacle, Thru hole, PCB mount Revisions Control Rev.
D*M High Density 104 Contacts 90 Bent PCB Terminations
Features/Benefits Compliant with ESA/ESCC specification Solderable PCB terminations Available with ot without brackets High density layouts Typical Applications Space equipments Avionics / Military Industrials
DISCONTINUED 10/20/2011
Physical Electrical Environmental Insulation Material: Glass filled LCP Flammability: UL 94V-0 Color: White Material: Copper Alloy Plating Underplating: Nickel Wiping Area: 2 μ [ 0.05 μm ] min. Gold over
656T Series Thermally Enhanced XSOP Socket
0805 656T Thermally Enhanced XSOP Socket Open top, Zero Insertion Force design for automatic loading Thermal contact for interfacing to thermal pad on package Thermal contact is timed to interface last
3M MetPak 2-FB Power Socket 2 mm 4/5-Row, Right Angle, Solder or Press-Fit Tail MP2 Series
6.50 Amps per contact End-to-end stackable Press or heat stake peg (solder tail) Futurebus+ compatible See the Regulatory Information Appendix (RIA) in the RoHS compliance section of www.mconnectors.com
.050" 4 thru 25 Contacts
.050" 4 thru 25 Contacts MM-11... MM-12... MM-12, MK-16, MK-18 receptacles MM-11, MK-15, MK-17 plugs PAGE 1 OF 4 PAGES BODY CONTACTS OPTIONS SERIES SIZE HARDWARE MM.050" Rugged Metal I/O Connector (MM
DETAIL SPECIFICATION SHEET
INCH-POUND MIL-DTL-55302/138C 10 September 2018 SUPERSEDING MIL-DTL-55302/138C 24 March 2004 DETAIL SPECIFICATION SHEET CONNECTORS, PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES: PLUG, PIN, 160 CONTACT POSITIONS,
3M Low Profile Header Straight and Right Angle, Four-Wall 303 Series
.100.100 Straight and Right ngle, Four-Wall 303 Series ll over gold flash Sturdy body End windows Low cost Straight or right angle Ejector/latch option not available See Regulatory Information ppendix
DISCONTINUED. 3M Accessories. Physical
3M ccessories.100.100 EMI System 3705/3706 Series Spring latch attachment allows quick, easy connect/ disconnect Fits existing 3M connectors Intra-cabinet grounding eliminates pigtails/ drain wires and
MAY-16 REV B2
Product Specification 108-20025 06-MAY-16 REV B2 The product described in this document has not been fully tested to ensure conformance to the requirements outlined below. Therefore, TE Connectivity (TE)
SMB. Aliner Industries, Inc. No. 32, Lane 387, Min-an Rd., Sinjhuang City, Taipei County 24256, Taiwan
SMB Aliner Industries, Inc. No. 32, Lane 387, Min-an Rd., Sinjhuang City, Taipei County 24256, Taiwan Tel : +886-2-2205-5791 E-mail : sales@aliner.com.tw Fax : +886-2-2203-8052 / 2205-5628 http://www.aliner.com.tw
Accessories / Screwlocks
3401-022 Accessories / Screwlocks Product Features Male or female screwlocks Residual magnetism level - Brass parts: NMB (200 Gamma max) - Stainless Steel parts: NMB (200 Gamma max) 1 part number for 1
Amphenol Amphenol Taiwan Corporation Sheet 1 of 9
Amphenol Amphenol Taiwan Corporation Sheet 1 of 9 Title: Part Number: Description: Micro Power Wafer Product Specification G881A / G881B / G881MA / G881H / G881C 3.0 mm Pitch, PCB Mount / SMT Type / CRIMPING
3M Mini D Ribbon (MDR) Connectors.050 Surfacemount Vertical Receptacle - Shielded 102 Series
M Mini D Ribbon (MDR) Connectors Wiper-on-wiper contact for reliable repetitive plugging Interface latch design for connection stability I 1284C Interface as a 6 contact connector Contacts: 20, 26 and
MIL-DTL Series I Connectors
RUGGED Self-locking bayonet coupling system 100% scoop proof 500-mating-cycle durability Excellent shock and vibration resistance Environmentally sealed and hermetic versions available VERSATILE Available
Amphenol RF- SMA Connector Series
Page 1 of 8 enter part number Products 7/16 1.0/2.3 1.6/5.6 AMC BNC / RP-BNC C FAKRA SMB FME HN MCX Mini-UHF Mini 75 Ohm SMB MMCX Precision (APC) QDS QMA QWS SC SlimLine BNC SMA / RP-SMA SMB SMC SMP TNC