Model Tubing O.D. (mm) Tubing I.D. (mm) 5 32 " 5 16 " Specifications

Transcription

1 Nylon Tubing Series T/TIA For general pneumatic tubing, Nylon tubing Max. Operating Pressure Max. operating pressure (MPa) T0 T00 Series TIA T3 T003 Other metric size Operating temperature ( C) How to measure the minimum bending radius. Fixed end At a temperature of 0 C, bend the tubing into a U shape. Fix one end and gradually move the other end closer. Measure ter's rate of change is %. Precautions. Applicable for general industrial water. Please consult with SMC if using other kinds of fluid. Surge pressure must be under the max. operating pressure. If the surge pressure exceeds the maximum operating pressure, it will result in damage to fittings and tubes..please exercise caution when using this item in a clean room. There is a possibility of plasticizer and other materials precipitating on the tube surface and detracting from the cleanliness level of the room. Tubing O.D. (mm) Tubing I.D. (mm) White (W) Red (R) Blue (BU) Yellow (Y) Green (G) 0 C or less Max. operating 0 C pressure Note ) 0 C (MPa) 0 C 0 C Applicable fittings Note ) Note ) Min. bending radius (mm) Note 3) Min. bending radius Bending value (Reference) Operating temperature Note ) Metric size (Series T) Inch size (Series TIA) T0 T003 T00 T0 T00 T7 T09 T3 TIA0 TIA0 TIA07 TIA TIA " " m roll 0 m roll (T3 is reel.) Tubing size Air/Water to +0 C, Water: 0 to +70 C (No freezing) Nylon One-touch fittings, Insert fittings, Self-align fittings, Miniature fittings Nominal size (inch) " 3 " " 3 " " Nominal size (mm) 3. Note ) Be sure to operate under the maximum operating pressure conditions using the lower maximum operating specification of either the tubing or fittings. Note ) Mount an inner sleeve when using metal One-touch fittings in high-temperature environments of 0 C or more. Use self-align fittings at a temperature of 0 C or less. Note 3) The minimum bending radius is the representative value measured as shown in the left figure. Therefore, refer to the refraction value and make sure that the tubing is not bent or flattened. by the method in the left figure if the tubing is bent or flattened, etc. T0 B Tubing model Color Symbol Color B Black (Translucent) W White ( color) R (Translucent) BU Blue (Translucent) Y Yellow (Translucent) G Green (Translucent) 0 0 Length per roll Symbol Length 0 0 m roll 0 0 m roll 3 0

2 For general pneumatic tubing Pliable soft nylon tubing Max. Operating Pressure Max. operating pressure MPa. TS0.0. TS00... Other than.0 TS0, TS Operating temperature C Precautions. Compatible with water due to a change in materials. Compatible fluid types are printed on the tube body for differentiation, so please be sure to check this. Note) If using the previous TS/TISA series with water, the tube may shrink and cause air leakage or the tube may fall out.. The products which changed the material are applicable for general industrial water. Please contact SMC if using other kinds of fluid. Surge pressure must be under the max. operating pressure. If the surge pressure exceeds the maximum operating pressure, it will result in damage to fittings and tubes. 3. Please exercise caution when using this item in a clean room. There is a possibility of plasticizer and other materials precipitating on the tube surface and detracting from the cleanliness level of the room. How to measure the minimum bending radius R At a temperature of 0 C, bend the tubing into a U shape. Fix one end and gradually move the other end closer. Measure R at the point where the outside diameter's rate of change is %. Fixed end Made to Order Soft Nylon Tubing Series TS/TISA 0 m roll 0 m roll (TS is reel.) Tubing size Metric size (Series TS) Inch size (Series TISA) TS0 TS00 TS00 TS7 TS09 TS TISA0 TISA0 TISA07 TISA TISA3 Tubing O.D. (mm) Tubing I.D. (mm) White (W) Red (R) Blue (BU) Yellow (Y) Green (G) Printing/ Previous NEW TS00 W Tubing model 3 " " Air/Water Note ) Max. 0 C or less operating 0 C pressure 0 C MPa 0 C Note ) 0 C Applicable fittings Note ) 3) Min. bending Min. bending radius radius mm Note ) Bending value (Reference) Operating temperature Note ) Print code SMC TS 00 SOFTNYLON x SMC TS 00 SOFTNYLON x 0 Length per roll Symbol Length 0 0 m roll 0 0 m roll (Black and white only) Nominal size (inch) " 3 " " 3 " " Air Air/Water Color Symbol Color B Black (Translucent) W White ( color) R Red (Translucent) BU Blue (Translucent) Y Yellow (Translucent) G Green (Translucent) (Please contact SMC for specifications in detail, dimensions, delivery and specifications other than those mentioned above.) 0 m reel Metric size and Inch size except ø: Suffix -X3 to the end of part number. Ex.) TS0R-0-X3 Longer length reel Metric size: Suffix -X3 to the end of part number. Ex.) TS0G-00-X3 0 m roll Inch size: Suffix -X to the end of part number. Ex.) TISA0BU-0-X Made to Order Availability Part no. Length TS0 TS00 TS00 TS7 TS09 TISA0 TISA0 TISA07 TISA TISA3 Color X3 0 m reel Black, White, 0 m reel Red, Blue, 00 m reel Yellow, Green 00 m reel X 0 m roll Red, Blue, Yellow, Green Nominal size (mm) One-touch fittings, Insert fittings, Self-align fittings, Miniature fittings to +0 C, Water: 0 to +0 C (No freezing) Nylon Note ) Refer to the Printing/. Note ) Be sure to operate under the maximum operating pressure and operating temperature conditions using the lower specifications of either the tubing or fittings. Note 3) Mount an inner sleeve when using metal One-touch fittings in high-temperature environments of 0 C or more. Use self-align fittings at a temperature of 0 C or less. Note ) The minimum bending radius is the representative value measured as shown in the left figure. sure that the tubing is not bent or flattened. the method in the left figure if the tubing is bent or flattened, etc. 0

3 Soft Polyurethane Tubing Series TUS Suitable for piping in confined spaces Extremely flexible Soft Polyurethane Tubing TUS related accessories lnner Sleeve Series TJ Reinforces soft polyurethane tubing. Insert an inner sleeve into soft polyurethane tubing when used with a One-touch fitting. Series Table Tube O.D. (mm) Tube I.D. (mm) White (W) Red (R) Blue (BU) Yellow (Y) Green (G) Opaque (N) () Yellow brown (YB) TUS0. TUS00 TUS00 : 0m roll TUS. : 0m roll TUS0 Part No. TJ-0 TJ-00 TJ-00 TJ- TJ-0 Wall thickness Applicable tube model TUS0 TUS00 TUS00 TUS TUS0 Length C700T (Nickel plated) 0.mm Precautions quse nylon or polyurethane tubing for general industry water to prevent the tubing from coming out or bursting due to possibility of surge pressure generation. wthe value of the max. operating pressure is at a temperature of 0 C. Refer to the burst pressure characteristics curve for other temperatures. Avoid abnormal temperature rise which may burst the tubing. ethe value of the min. bending radius is at a temperature of 0 C. Higher temperatures allows the tubing to bend more. ruse inner sleeve taking the removing force into consideration when used with Onetouch fittings. Max. operating pressure Burst pressure Applicable tube fitting Min. bending radius (mm) Operating temperature () Tube drawing Without strenght N inner sleeve (Using One-touch fitting) With inner sleeve Air 0.MPa at 0 C Refer to burst pressure characteristics curve. One-touch fitting, Insert tube fitting, Hose nipple (3) 9 0 to +0 C (No freezing) Polyurethane Note) Not clear but opaque due to material. Note) Min. bending radius is measured as shown in the figure below. Note3) Always use inner sleeve (Series TJ) in safety circuit or critical area. TUS B Indication of tube model Bend the tube into U-form at a temperature of 0 C. Fix one end and close loop gradually. Measure R when the tube breaks or is crushed. 0 Burst Pressure Characteristics Curve Length per roll Symbol Roll size Colour indication 0 0m roll Symbol Colour 0 0m roll (Black, Blue only) B Black W White R Red BU Blue Y Yellow G Green N Opaque YB Yellow brown

4 Hard Polyurethane Tubing Series TUH TUS Soft Polyurethane TU Polyurethane Hard Polyurethane TUH (Standard Type) Soft Hard Maximum effective area increased nearly % TUH/Standard Type (Compared to polyurethane tubing TU00: O.D. mm, length m) O.D. (ød) I.D. (ød) Tubing inside diameter comparison Tubing O.D. (ød) TUH/Standard type Tubing TUH/High pressure type I.D. (ød) TU (mm). Operating pressure.0mpa (at 0 C) TUH/High Pressure Type Has the same operating pressure as series TS soft nylon tubing, and a bending radius equivalent to series TU polyurethane tubing. Can be restored even after folding Restoration is outstanding compared to nylon tubing, leaving no creases from folding.

5 Hard Polyurethane Tubing/Standard Type Series TUH Series 0m bundle 0m bundle TUH0 TUH0 TUH0 TUH73 TUH O.D. mm I.D. mm White (W) Blue (BU) Translucent (N) Max. operating pressure (at 0 C) Air Note ) 0.MPa Note ) Min. bending radius mm 30 3 Burst pressure Refer to the burst pressure characteristics curve. R Operating temperature 0 to 0 C Fixed side At a temperature of 0 C bend the tubing into a U shape. Then with one side fixed, gradually close the other side and measure R at the point where the tubing folds or flattens, etc. Polyurethane Note ) Consult SMC regarding other fluids. Water cannot be used due to the occurrence of hydrolysis. Note ) The maximum operating pressure is the value at 0 C. Refer to the burst pressure characteristic curve for other temperatures. Furthermore, an abnormal temperature increase due to adiabatic compression can cause tubing to burst. Note 3) The minimum bending radius is measured at 0 C using the method shown in the figure at the left. At higher temperatures, breakage or flattening, etc., may occur at more than the minimum bending radius. Burst Pressure Characteristic Curve and Operating Pressure TUH0 B 0 Burst pressure MPa 3 Maximum operating pressure Operating temperature C Tubing model Color Symbol B W BU N Symbol 0 0 Color Black White Blue Translucent Bundle length Length 0m bundle 0m bundle

6 Hard Polyurethane Tubing/High Pressure Type Series TUH Series 0m bundle 0m bundle TUH0 TUH00 TUH00 TUH TUH0 O.D. mm I.D. mm.. White (W) Blue (BU) Translucent (N) Max. operating pressure (at 0 C) Air Note ).0MPa Note ) Min. bending radius mm Fixed side R At a temperature of 0 C bend the tubing into a U shape. Then with one side fixed, gradually close the other side and measure R at the point where the tubing folds or flattens, etc. Burst pressure Operating temperature Refer to the burst pressure characteristics curve. 0 to 0 C Polyurethane Note ) Consult SMC regarding other fluids. Water cannot be used due to the occurrence of hydrolysis. Note ) The maximum operating pressure is the value at 0 C. Refer to the burst pressure characteristic curve for other temperatures. Furthermore, an abnormal temperature increase due to adiabatic compression can cause tubing to burst. Note 3) The minimum bending radius is measured at 0 C using the method shown in the figure at the left. At higher temperatures, breakage or flattening, etc., may occur at more than the minimum bending radius. Burst Pressure Characteristic Curve and Operating Pressure 7 TUH00 B 0 Burst pressure MPa 3 Maximum operating pressure Tubing Color Symbol B W BU N Bundle length Symbol Length 0 0m bundle 0 0m bundle Color Black White Blue Translucent Operating temperature C

7 Series TUH/ Specific Product Precautions Be sure to read before handling. Precautions on Usage. Water cannot be used due to the occurance of hydrolysis. Use nylon or polyurethane tubing for general industrial water. Furthermore, consult SMC regarding use with any fluids other than air.. The maximum operating pressure is the value at 0 C. Refer to the burst pressure characteristic curve for other temperatures. Furthermore, an abnormal temperature increase due to adiabatic compression can cause tubing to burst. 3. The minimum bending radius indicates the value at which the tubing will fold at a temperature of 0 C. At higher temperatures, the tubing may fold at more than the minimum bending radius.. Store away from direct sunlight in a location at no more than 0 C. 7

8 FEP Tubing (Fluoropolymer) Heat resistance:00 C It changes according to the operating pressure. Refer to the graph of the max. operating pressures on page. Colour variations Translucent Black Red Blue Size variations Metric size: ø to ø Applicable fittings One-touch fittings (Series KQ,KJ) Miniature fittings (Series M,MS) (Hose nipple type) Insert fittings (Series KF) High Purity Fluoropolymer fittings (Series LQ) Series TH Applications General pneumatic piping Food Semiconductor Medical care Automobile Certified to current Food Sanitation Legislation Ministry of Japanese Health and Safety, directive #370,99

9 FEP Tubing (Fluoropolymer) Series TH Series Tubing O.D. (mm) Tubing I.D. (mm) -0m roll -0m roll Metric size TH00 TH0 TH00 TH00 TH7 TH0 TH09 TH Colour Symbol Translucent N Red (Translucent) R Blue (Translucent) BU Black (Opaque) B How to measure the minimum bending radius. Fixed end R At a temperature of 0 C, bend the tubing into a U shape. Fix one end and gradually move the other end closer. Measure R at the point where the outside diameter's rate of change is %. Max. Operating Pressure Max. Operating Pressure MPa 3 0. TH00 TH0 TH00 TH0/TH TH00/TH7/TH Operating Temperature C Note) The maximum operating pressure varies dependant on the I.D. bore size even if the O.D. is the same. Applicable fittings Note ) Note ) Metric size Inch nominal size /3" Inch nominal size /" One-touch fittings: Series KQ, KJ Insert fittings: Series KF Fluoropolymer fittings: Series LQ Miniature fittings: Series M, MS (Hose nipple type) Max. operating pressure Refer to below Max. Operating Pressure. Min. bending Note 3) radius (mm) Note ) Operating temperature Air, Inert gas: -0 to 00 C Water: 0 to 0 C (No freezing) FEP (Fluorinated Ethylene Propylene Resin) Note ) When using a fluid in liquid form, the surge pressure must not exceed the maximum operating pressure. A surge pressure higher than the maximum operating pressure can cause breakage of the fittings, or rupture of the tubing. Furthermore, an abnormal temperature increase due to adiabatic compression can also result in ruptured tubing. Note ) Do not use in locations where the FEP tubing will move. Be sure to operate under the maximum operating pressure conditions using the lower maximum operating specification of either the tubing or fittings. After long term use or under high temperatures, some fittings leakage may occur due to material deterioration with age. Perform periodic inspections, and if any leakage is detected, replace with a new product immediately. (Refer to maintenance part of "Tubing Precautions " on the page 7-.) Refer to Best Pneumatics in "Fittings and Tubing" for all other precautions. For High Purity Fluoropolymer, refer to the precautions of CAT.ES70-7, "High Purity Fluoropolymer Fittings & Tubing." Note 3) Minimum bending radius is measured as shown left as representative values. Allow extra length when piping since the tubing may crush if bent more than the min. bending radius. Note ) Consult SMC if using any other fluids. TH00 N 0 Indication of tubing model Colour indication Symbol Colour N Translucent R Red (Translucent) BU Blue (Translucent) B Black (Opaque) Air, Water Note ), Inert gas Length per roll Symbol Roll size 0 0m roll 0 0m roll ) ) The 0m roll is only in the colour natural as standard available 9

10 Chemical Resistance of the Fluoropolymer FEP Chemicals in this table are inactive against FEP material Note ), however physical properties may be effected by temperature or pressure change. Please make sure that operating conditions do not cause problems since the use of FEP tubing under chemical environment is unsecured. -nitro--methyl propanol -nitrobutanol Pentabasic benzamide N-butylamine N-octadecanol N-butyl acetate O-cresol Di-isobutyl adipate Acetophenone Acetone Alniline Abietic acid Sulphuric chloride Isooctane Liquid ammonia Ethyl alcohol Ethyl ether Ethylene glycol Ethylenediamine Zinc chloride Aluminum chloride Ammonium chloride Calcium chloride Sulphuric chloride Iron chloride (III) Benzoyl chloride Magnesium chloride Hydrochloric acid Chlorine (absolute) Aqua regia Ozone Hydrogen peroxide Natrium peroxide Gasoline Permanganate Formic acid Xylene Chromic acid Chlorosulfonic acid Chloroform Paraffinum liquidum Allyl acetate Ethyl acetate Potassium Butyl acetate Sodium hypochlorite Carbon tetrachloride Dioxane Cyclohexanone Cyclohexane Dimethyl ether Dimethylsulfoxide Dimethylformamide Bromine Deionized water Nitric acid Mercury Ammonium hydroxide Potassium hydroxide Sodium hydroxide Cetane Soap, detergent Dibutyl sebacate Diethyl carbonate Tetrachloroethylene Tetrahydrofuran Tetrabromoethane Triethanolamine Trichloroethylene Trichloroacetic acid Toluene Naphtha Naphthalene Naphthol Lead Carbon dioxide Nitrogen dioxide Nitrobenzene Nitromethane Perchloroethylene Perphloroxylene Unsymmetrical dimethylhydrazine Hydrazine Pinene Piperidine Glacial acetic acid (Acetic acid) Pyridine Phenol Phthalic acid Dybutyl phthalate Dimethyl phthalate Hydrofluoric acid Naphthalene fluoride Nitrobenzene fluoride Furan Hexachlorethane Hexane Ethyl hexanoate Phenylcarbinol Benzaldehyde Benzonitrile Borax Boric acid Formic aldehyde (Formalin) Acrylic anhydride Acetic anhydride Methacrylic acid Allyl methacrylate Vinyl methacrylate Methyl alcohol Methyl ethyl ketone Methylene chloride Sulphuric acid Phosphoric acid Iron phosphate (III) Tri-n-butyl phosphate Tricresyl phosphate Note ) Inactive in chemistry terminology means - not to cause any chemical reaction. Reference cited: Teflon, the fluoropolymer handbook, Manual for the chemical applications of Teflon. Du Pond-Mitsui Fluorochemicals Co., Ltd. Teflon is a registered trademark for the fluoropolymer produced by E.I du Pond de Nemours & Company (Inc.) and Du Pond-Mitsui Fluorochemicals Co., Ltd.

11 Series TH Tubing Precautions Be sure to read before handling. Selection Warning. Confirm the specifications. The products appearing in this catalogue are designed for use only in compressed air systems (including vacuum). Do not use outside the specified ranges of pressure, temperature, etc., as this may cause damage or malfunction. (Refer to specifications.) SMC cannot assure the product quality when fluids other than air, water and inert gas are used. Consult with SMC for details.. In case of using the product for medical care This product is designed for use with compressed air system applications for medical care purposes. Do not use in contact with human bodily fluids, body tissues or transfer applications to a human living body.. Do not use in locations where the connecting threads and tubing connection will slide or rotate. The connecting theads and tubing connection will come apart under these conditions. Use rotary type one-touch fittings (Series KS, KX) in cases where sliding or rotation will occur. Only air can be used as the operating fluid, when using rotary type one-touch fittings.. Use tubing at or above the minimum bending radius. Using below the minimum bending radius can cause breakage or flattening of the tubing. 3. Never use the tubing for anything flammable, explosive or toxic such as, gas, fuel gas, or cooling mediums, since the contents can penetrate outward. Mounting. Before mounting confirm the model and size, etc. Also, confirm that there are no blemishes, nicks or cracks in the product.. When tubing is connected, consider factors such as changes in the tubing length due to pressure, and allow sufficient leeway. 3. Mount so that fittings and tubing are not subjected to twisting, pulling or moment loads. This can cause damage to fittings and flattening, bursting or disconnection of tubing, etc.. Mount so that tubing is not damaged due to tangling and abrasion. This can cause flattening, bursting or disconnection of tubing, etc. Piping. Preparation before piping Before piping is connected, it should be thoroughly blown out with air (flushing) or washed to remove chips, cutting oil and other debris from inside the pipe. Do not allow chips of the piping thread or the seal material to go in. Air Supply Warning. Types of fluid This product is designed for use with compressed air. Consult SMC if a different fluid is to be used. Consult SMC regarding products for use with general purpose fluids, to confirm which fluids can be used.. When there is a large amount of drainage. Compressed air containing a large amount of drainage can cause the malfunction of pneumatic equipment. An air dryer or Drain Catch should be installed upstream from filters. 3. Drain management If air filter drains are not flushed regularly, the drainage will flow downstream leading to the malfunction of pneumatic equipment. In cases where the management of drain flushing will be difficult, the use of filters with automatic drains is recommended. For details on the quality of compressed air mentioned above, refer to SMC's "Best Pneumatics" catalogue vol.. Operating Environment Warning. Do not operate in locations in an explosive atmosphere.. Do not operate in locations where vibration or impact occurs. 3. In locations near heat resources, block off radiant heat. Maintenance. Check for the following during regular maintenance, and replace components as necessary. a) Scratches, gouges, abrasion, corrosion b) Leakage c) Twisting, flattening or distortion of tubing d) Hardening, deterioration or softness of tubing. Do not repair or patch the replaced tubing or fittings for reuse. 3. When using insert or miniature fittings over a long period, some leakage may occur due to age deterioration of the materials. Perform periodic inspections, and if any leakage is detected, correct the problem by additional tightening. If tightening becomes ineffective, replace the fittings with a new product immediately.

12 Polyurethane Coil Tubing Series TCU For flexible tubing Compact piping possible Burst Pressure Characteristics Curve Number of tubes Tube O.D. (mm) Tube I.D. (mm) Max. operating pressure () Burst prssure Operating temperature Colour TCU 0B- TCU 0B- TCU 0B-3 TCU 00B Air () TCU 00B- 0.MPa at 0 C Refer to pressure characteristics curve. 0 to +0 C Polyurethane Black Note ) Consult SMC if using for other fluids than air. Note ) Refer to burst pressure characteristics curve for other temperatures. Avoid abnormal temperature rises. Dimensions TCU 00B-3 TCU 00B- Spec. Part No. TCU0B- TCU0B- TCU0B-3 TCU00B- TCU00B- TCU00B-3 TCU00B- Made to Order Change of coil turns, Color change Tube size (mm) O.D. I.D.. Dimensions are changeable due to material. Dimension of coil (mm) No. of tubes No. coil windings per tube length L ød (Consult SMC for detailed specifications, dimensions and delivery.) Max. operating length (m).. Standard unit of packing tubes/ case Spec. Tube size (mm) Coil (mm) No. coil No. of windings Max. operating Part No. O.D. I.D. L ød tubes per tube length length (mm) TCU0 -- N -X N X 3 to 90 L X TCU0 -- N -X. N X 3 to 90 L X TCU0-3- N -X N X 3 3 to 3 L X TCU00 -- N -X N X 3 to 90 L X TCU00 -- N -X N X 37 3 to L X TCU00-3- N -X N X to L X B (Black), W (White), R (Red), BU (Blue), Y (Yellow), G (Green), C (Clear), YR (Orange) N Coil turns Spec. Part No. TCU00 -- N -X TCU00 -- N -X TCU -- N -X TCU -- N -X TCU0 -- N -X TCU0 -- N -X Tube size (mm) Coil (mm) O.D. I.D. L ød N X 3 N X. N X N X 0 N X 7 N X 7 No. of tubes No. coil windings per tube length 3 to 90 L X to 0 3 to 3 to 3 3 to 3 3 to 30 Max. operating length (mm) L X L X + 00 L X L X + 00 L X

13 Polyurethane Flat Tubing Series TFU Compact piping possible Burst Pressure Characteristics Curve Part No. Number of tubes Tube O.D. (mm) Tube I.D. (mm) Max. operating pressure () Burst prssure Operating temprature Colour Min. bending radius (mm) Tube length per roll (m) TFU 0B- TFU 0B-3 3 TFU 00B- TFU 00B-3 3 Air () TFU 00B-. 0.MPa at 0 C Refer to burst pressure characteristics curve 0 to +0 C (No freezing) Polyurethane Black 0 Note) Consult SMC if using for other fluids than air. Note) Refer to burst pressure characteristics curve for other temperatures. Avoid abnormal temperature rises. TFU 00B-3 3 TFU0 B Indication of tube model Colour indication Symbol Colour B Black Number of tubes Symbol Number 3 3 Made to Order q Colour change (m roll) Suffix X to the end of part number. Ex.) TFU00BU--- X W: White, R: Red, BU: Blue, Y: Yellow, G: Green, C: Clear, YR: Orange (All tubes are same colour.) w Longer roll length (0m or 0m roll) Suffix X3 to the end of part number. Ex.) TFU0B--0- X3 e Number of tubes (m roll) Suffix X to the end of part number. Ex.) TFU00B--- X TFU0 TFU00 TFU00 TFU TFU0 Tube O.D. (mm) Tube I.D. (mm).. Number of tubes 3 7 (Consult SMC for detailed specifications, dimensions and delivery.) : m roll : 0m roll : 0m roll 3

14 Flame Resistance (Equivalent to UL-9 Standard V-0) FR Soft Nylon Tubing Series TRS Applicable for general air pressure and water in a spark atomosphere such as spot welding. Flame resistance tube Series Table Tube O.D. (mm) Tube I.D. (mm) White (W) TRS003 3 TRS00 : 0m roll : 0m roll TRS TRS0. Burst Pressure Characteristics Curve Red (R) Blue (BU) Green (G) Max. operating pressure Burst pressure Min. bending radius (mm) 7 Air, Water.MPa at 0 C Refer to burst pressure characteristics curve Operating temperature 0 to +0 C (Water: 0 to 0 C)(No freezing) Flame resistance nylon (UL-9 Standard V-0) Precautions qapplicable for general industry water. Consult SMC if using for other kinds of fluid. Surge pressure must be under the max. operating pressure. If exceeding that value, fitting may be damaged and tubing may be burst. wthe value of the max. operating pressure is at a temperature of 0 C. Refer to the burst pressure characteristics curve for other temperatures. Avoid abnormal temperature rises which may burst the tubing. ethe value of the min. bending radius is at a temperature of 0 C and O.D. variable rate % max. In case that operating temperature is higher than 0 C, O.D. variable rate may be over % even if bending radius is within the specified range. TRS B Indication of tube model 0 Colour indication Symbol Colour B Black W White R Red BU Blue G Green Length per roll Symbol Roll size 0 0m roll 0 0m roll

15 Flame Resistance (Equivalent to UL-9 Standard V-0) FR Double Layer Tubing Series TRB Suitable for air and water piping in environments where sparks from spot welders, etc., may be a problem. Double layer design using flame resistant resin (equivalent to UL-9 Standard V-0) for outer layer. Series Table Inner tube O.D. (mm) Inner tube I.D. (mm) Outer layer thickness (mm) () Outer layer colour White (W) Red (R) Blue (BU) Yellow (Y) Green (G) : 0m roll : 0m roll TRB00 TRB00 TRB7 TRB Minimum bending () radius (mm) 3 Burst Pressure Characteristics Curve Air, Water () Max. operating pressure (3) Burst pressure Ambient and fluid temperature Inner tube Outer layer.0mpa at 0 C Refer to burst pressure characteristics curve. 0 to +0 C (Water: 0 to 0 C) (No freezing) Nylon PVC (Equivalent to UL-9 Standard V-0) Note) The colour of all inner tube is black. Note) Applicable for general industry water. Consult SMC if using for other kinds of fluid. Surge pressure must be under the max. operating pressure. Note3) Refer to burst pressure characteristics curve for other temperatures. Avoid abnormal temperature rises. Note) The value for a temperature of 0 C and O.D.variable rate % max. TRB7 B 0 Indication of tube model Colour indication Symbol Colour Symbol Colour B W R Black White Red BU Y G Blue Yellow Green Length per roll Symbol 0 0 Roll size 0m roll 0m roll

16 FR Double Layer Tubing Series TRB How to Install to One-touch Fitting Length of tube to be inserted into One-touch fitting is indicated on the outer layer of TRB tubing. Cut the tube according to this indication. (Procedureq) and then strip off the outer layer. (Procedurew) for installing tube. Precautions qapplicable for general industrial water. Consult SMC if using for other kinds of fluid. Surge pressure must be under the max. operating pressure. If exceeding that value, fitting may be damaged and tubing may be burst. wthe value of the max. operating pressure is at a temperature of 0 C. Refer to the burst pressure characteristics curve for other temperatures. Avoid abnormal temperature rises which may burst the tubing. ethe value of the min. bending radius is at a temperature of 0 C and O.D. variable rate % max. In case that operating temperature is higher than 0 C, O.D. variable rate may be over % even if bending radius is within the specified range.

17 Flame Resistant (Equivalent to UL-9 Standard V-0) FR Double Layer Polyurethane tubing SeriesTRBU Series Table - 0m bundle - 0m reel TRBU00 Internal tube O.D. mm Internal tube I.D. mm External layer thickness mm TRBU00 TRBU TRBU0. Internal tube External layer Note ) External layer colour White (W) Red (R) Blue (BU) Yellow (Y) Green (G) Sectional view of FR double layer tube Note ) Minimum bend radius mm Note ) Air, Water Note 3) Maximum operating pressure (at 0 C) Burst pressure Ambient and fluid temperature 0.MPa {.kgf/cm } Refer to burst pressure characteristics curve 0 to 0 C For water 0 to 0 C (without freezing) Burst Pressure Characteristics Curve and Operating Pressure.0 s Internal tube External layer Polyurethane PVC (equivalent to UL-9 standard V-0) Note ) The colour of all internal tubes is black. Note ) Can be used with general industrial water. Contact SMC if used with other fluids. Also keep surge pressure at or below the maximum operating pressure. Note 3) In case of other temperatures, refer to the burst pressure characteristics curve. In addition, operate so that abnormal temperature rise due to adiabatic compression does not occur. Note ) Indicates the bending value of the tubing at a temperature of 0 C. TRBU B 0 Burst pressure MPa Burst pressure Maximum operating pressure Operating temperature C Tube model Colour Symbol B W R Colour Black White Red Roll length Symbol 0 0 Symbol BU Y G Length 0m bundle 0m reel Colour Blue Yellow Green 7

18 FR Double Layer Polyurethane Tubing Series TRBU Installation on One-touch Fittings Since the pitch length for installation on a One-touch fitting is indicated on the external layer of TRBU tubing, cut the tubing according to this indication (Step ), strip off the external layer only (Step ), and then install on the One-touch fitting. x SMC FR TUBE TRBU00 x Pitch indication: All installation lengths with same pitch Step x SMC FR TUBE TRBU00 x Step Cut internal and external layers x SMC FR TUBE Strip off external layer only Precautions on Useage. Useage is possible with general industrial water. Contact SMC if product will be used with other fluids. Also, keep surge pressure at or below the maximum operating pressure. If surge pressure exceeds the maximum operating pressure, this can cause damage to fittings or bursting of the tubing.. The maximum operating pressure is the value when at 0 C. In case of other temperatures, refer to the burst pressure characteristics curve. Furthermore, bursting of the tubing can be caused by an abnormal temperature rise due to adiabatic compression. 3. The minimum bend radius indicates the bending value of the tubing at a temperature of 0 C. The tubing may bend beyond the minimum bend radius at higher temperatures.. Tubing should be stored in a location out of direct sunlight and at 0 C or below.

19 Antistatic Tubing Series TA Conductive tubing prevents troubles caused by static electricity. Antistatic soft nylon tubing/series TAS For air pressure piping to product or assembly while preventing static electricity. Flame resistant tube (UL-standard, V-0) Burst Pressure Characteristics Curve Series Table Tube O.D. (mm) Tube l.d. (mm) TAS3 3.. TAS0. TAS00 : 0m roll : 0m roll TAS00 TAS. TAS0 () Max. operating pressure.mpa at 0 C Burst pressure Refer to burst pressure characteristics curve. Min. bending radius (mm) () Operating temperature 0 to 0 C Surface resistance Conductive nylon + Flame resistant nylon (UL-9standard, V-0) to 7 Ω Note) Refer to burst pressure characteristics curve for other temperatures. Avoid abnormal temperature rises. Note) The value at temperature of 0 C and O.D. variable rate % max. TAS B 0 Indication of tube model Colour indication Symbol Colour B Black Length per roll Symbol Roll size 0 0m roll 0 0m roll For air pressure piping to product or assembly while preventing static electricity. Flexible tube Antistatic polyurethane tubing/se ries TAU Series Table Tube O.D. (mm) Tube l.d. (mm) TAU30 3. TAU0. TAU00 : 0m roll : 0m roll TAU00 TAU. TAU0 Burst Pressure Characteristics Curve () Max. operating pressure Burst pressure 0.9MPa at 0 C Refer to burst pressure characteristics curve. Min. bending radius (mm) () Operating temperature 0 to 0 C Conductive polyurethane Surface resistance to 7 Ω Note) Refer to burst pressure characteristics curve for other temperatures. Avoid abnormal temperature rises. Note) The value at temperature of 0 C. TAU B 0 Indication of tube model Colour indication Symbol Colour B Black Length per roll Symbol Roll size 0 0m roll 0 0m roll 9