DRY-FLO Separators DRY-FLO DRY-FLO

Transcription

1 DRYFLO eparators The stainless steel separating tube diffuser causes the steam to enter a controlled centrifugal flow. Due to the centrifugal motion, entrained liquids and solids are directed to the outer walls of the separator. Reentrainment breaker plates create a quiet inert zone to prevent liquids and solids from reentering the flow stream once separation has taken place. With correct sizing and proper drainage these separators are designed to eliminate 99% of all entrained liquids and solids that are 10 microns and larger in size. All DRYFLO separators are manufactured in accordance with AME ode ection VIII Div 1. All models are available in carbon steel and stainless grades. Most material types are available upon request. DRYFLO Applications: Keep steam equipment clean and eliminates fouling of regulators, burgines, valves, etc. Removes moisture form compressed air lines in plant service. Removes line scale, liquids and other contaminants from process gas and air lines Removes condensate and oil from compressed gasses in intercooler and aftercooler service at compressor stations.

2 TYPE: Horizontal or Vertical downflow installations MODEL: DryFlo L1 Moisture eparator TB No Date 199 PRODUT, IN. Model L eparators are designed for horizontal or vertical downflow installations. The stainless steel eparating Tuyere Diffuser causes the stream to enter a controlled centrifugal flow. Due to the centrifugal motion, entrained liquids and solids are directed to the outer walls of the separator. Reentrainment breaker plates create a quiet inert zone to prevent liquid from reentering the flow stream once separation has taken place. With correct sizing and proper drainage, these separators are designed to eliminate 99% of all entrained liquids and particles that are 10 microns and larger in size. The Model L eparators can be fabricated from carbon steel or stainless steel and are manufactured in accordance with AME ode ection VIII, Division 1. A B PIPE IZE 1 1/ 2 1/ PIG 500 PIG A B TD WEIGHT WEIGHT DIMENION AND WEIGHT 2 1/ 5 9/1 6 5/ 6 5/ 8 5/ 10 3/ 12 3/ / 1 1/ 1 1/ 2 1/ 2 1/ * * * PHONE FAX

3 PRODUT, IN. TYPE: Horizontal installations MODEL: DryFlo L1 Moisture eparator TB No Date 199 Model L1 eparators are designed f or horizontal flow installations and are similar to the Model L eparators with the addition of a sump area to allow for a liquid holdup capacity. If required, the sump area may be lengthened from the standard dimensions shown below to allow for a larger liquid holdup capacity. The stainless steel epar ating Tuyere Diffuser causes the stream to enter a controlled centrifugal flow. Due to the centrifugal motion, entrained liquids and solids are directed to the outer walls of the separator. Reentrainment breaker plates create a quiet inert zone to prevent liquid from reentering the flow stream once separation has taken place. With correct sizing and proper drainage, these separators are designed to eliminate 99% of all entrained liquids and particles that are 10 microns and larger in siz e. The Model L1 eparators can be fabricated from carbon steel or stainless s teel and are manufactured in accordance with the AME ode ection VIII, Division 1. PIPE IZE 1 1/ 2 1/ A B / 5 9/1 6 5/ 6 5/ 8 5/ 10 3/ 12 3/ DIMENION AND WEIGHT E / 14 1/ 16 1/ 17 1/ 19 1/ F 8 1/ G 6 3/ 6 3/ 6 3/ 6 3/ 6 3/ 6 3/ 6 3/ 7 7/ 7 7/ 7 7/ 7 7/ 7 7/ 9 1/ 9 1/ 10 1/ 10 1/ LIQUID HOLDUP 150 PIG 500 PIG H TD U. FT. WEIGHT WEIGHT / 2 7/ 2 7/ 3 1/ 4 1/ 5 9/1 6 5/ 8 5/ 10 3/ 10 3/ 12 3/ / 1 1/ 1 1/ 2 1/ 2 1/ * * * PHONE FAX

4 PRODUT, IN. TYPE: Vertical Upflow installations MODEL: DryFlo L2 Moisture eparator TB No Date 199 Model L eparators are designed for vertical upflow installations only. The stainless steel eparating Tuyere Diffuser causes the stream to enter a controlled centr ifugal flow. Due to the centrifugal motion, entrained liquids and solids are directed to the outer walls of the separator. Reentrainment breaker plates create a quiet iner t zone to prevent liquid from reentering the flow stream once separation has taken place. With correct sizing and proper dr ainage, these separators are designed to eliminate 99% of all entr ained liquids and particles that are 10 microns and larger in siz e. The Model L eparators can be fabricated from carbon steel or stainless steel and are manufactured in accordance with the AME ode ection VIII, Division I. B A PIPE IZE 1 1/ 2 1/ DIMENION AND WEIGHT 150 PIG 500 PIG A B TD WEIGHT WEIGHT / 6 5/ 8 5/ 8 5/ 10 3/ / 1 1/ 1 1/ 2 1/ 2 1/ * * * PHONE FAX

5 PRODUT, IN. TYPE: Vertical down / Horizontal out flow installations MODEL: DryFlo L3 Moisture eparator TB No Date 199 Model L eparators are designed for vertical down and a horizontal out flow installation only. The stainless steel eparating Tuyere Diffuser causes the stream to enter a controlled centr ifugal flow. Due to the centrifugal motion, entrained liquids and solids are directed to the outer w alls of the separ ator. Reentrainment breaker plates create a quiet inert zone to prevent liquid from reentering the flow stream once separation has taken place. With correct sizing and proper drainage, these separators are designed to eliminate 99% of all entrained liquids and particles that are 10 microns and larger in siz e. The Model L eparators can be fabricated from carbon steel or stainless steel and are manufactured in accordance with the AME ode ection VIII, Division I. R T PIPE IZE 1 1/ 2 1/ DIMENION AND WEIGHT 150 PIG 500 PIG R T TD WEIGHT WEIGHT 2 1/ 5 9/1 6 5/ 6 5/ 8 5/ 10 3/ 12 3/ / / / 1 1/ 1 1/ 2 1/ 2 1/ * * * PHONE FAX

6 PRODUT, IN. TYPE: Horizontal In / Vertical downflow installations MODEL: DryFlo L4 Moisture eparator TB No Date 199 Model L eparators are designed for horizontal inlet and a vertical down outlet flow installation only. The stainless steel eparating Tuyere Diffuser causes the stream to enter a controlled centrifugal flow. Due to the centrifugal motion, entrained liquids and solids are directed to the outer walls of the separator. Reentrainment breaker plates create a quiet iner t zone to prevent liquid from reentering the flow stream once separation has taken place. With correct sizing and proper drainage, these separators are designed to eliminate 99% of all entrained liquids and particles that are 10 microns and larger in siz e. The Model L eparators can be fabricated from carbon steel or stainless steel and are manufactured in accordance with the AME ode ection VIII, Division I. V U K PIPE IZE 1 1/ 2 1/ DIMENION AND WEIGHT 150 PIG 500 PIG K U V TD WEIGHT WEIGHT 2 1/ 5 9/1 6 5/ 6 5/ 8 5/ 10 3/ 12 3/ / / / 1 1/ 1 1/ 2 1/ 2 1/ * * * PHONE FAX

7 PRODUT, IN. TYPE: Horizontal In / Vertical Upflow installations MODEL: DryFlo L5 Mositure eparator TB No Date 199 Model L eparators are designed for horizontal inlet and a vertical upflow installation only. The stainless steel eparating Tuyere Diffuser causes the stream to enter a controlled centr ifugal flow. Due to the centrifugal motion, entrained liquids and solids are directed to the outer w alls of the separator. Reentrainment breaker plates create a quiet iner t zone to prevent liquid from reentering the flow stream once separation has taken place. With correct sizing and proper drainage, these separators are designed to eliminate 99% of all entrained liquids and particles that are 10 microns and larger in siz e. The Model L eparators can be fabricated from carbon steel or stainless steel and are manufactured in accordance with the AME ode ection VIII, Division I. E F G PIPE IZE 1 1/ 2 1/ DIMENION AND WEIGHT 150 PIG 500 PIG E F G TD WEIGHT WEIGHT 2 1/ 6 5/ 8 5/ 8 5/ 10 3/ / 1 1/ 1 1/ 2 1/ 2 1/ * * * PHONE FAX

8 PRODUT, IN. TYPE: Horizontal In / Vertical downflow installations MODEL: DryFlo L6 Moisture eparator TB No Date 199 Model L eparators are designed for horizontal inlet and vertical down outlet or vertical up inlet and horizontal outlet flow installation only. The stainless steel eparating Tuyere Diffuser causes the stream to enter a controlled centrifugal flow. Due to the centrifugal motion, entrained liquids and solids are directed to the outer walls of the separator. Reentrainment breaker plates create a quiet iner t zone to prevent liquid from reentering the flow stream once separation has taken place. With correct sizing and proper drainage, these separators are designed to eliminate 99% of all entrained liquids and particles that are 10 microns and larger in siz e. The Model L eparators can be fabricated from carbon steel or stainless steel and are manufactured in accordance with the AME ode ection VIII, Division I. W T X PIPE IZE 1 1/ 2 1/ DIMENION AND WEIGHT 150 PIG 500 PIG T W X TD WEIGHT WEIGHT 2 1/ 5 9/1 6 5/ 6 5/ 8 5/ 10 3/ 12 3/ / / 1 1/ 1 1/ 2 1/ 2 1/ * * * PHONE FAX

9 PRODUT, IN. TYPE: Vertical Up / Horizontal outflow installations MODEL: DryFlo L7 Moisture eparator TB No Date 199 Model L7 eparators are designed for vertical upflow inlet and a horizontal outlet flow installation only. The stainless steel eparating Tuyere Diffuser causes the stream to enter a controlled centrifugal flow. Due to the centrifugal motion, entrained liquids and solids are directed to the outer walls of the separator. Reentrainment breaker plates create a quiet inert zone to prevent liquid from reentering the flow stream once separation has taken place. With correct sizing and proper drainage, these separators are designed to eliminate 99% of all entrained liquids and particles that are 10 microns and larger in siz e. The Model L7 eparators can be fabricated from carbon steel or stainless steel and are manufactured in accordance with the AME ode ection VIII, Division I. G H J PIPE IZE 1 1/ 2 1/ DIMENION AND WEIGHT 150 PIG 500 PIG G H J TD WEIGHT WEIGHT 2 1/ 6 5/ 8 5/ 8 5/ 10 3/ / 1 1/ 1 1/ 2 1/ 2 1/ * * * PHONE FAX

10 PRODUT, IN. TYPE: Horizontal flow installations only MODEL: DryFlo T Moisture eparator TB No Date 199 Gas, laden with moisture, enters the inlet of the separator where a deflector plate directs the flow in a downward centrifugal motion. The entrained moisture is then separated out of the flow by a reduction in velocity. The separated liquid is sent to the outer walls of the separator and falls below the reentrainment breaker plate where it is prevented for reentering the flow stream. A dry, clean flow then results, exiting upward through the outlet of the separ ator. With correct sizing and proper drainage, these separators are designed to eliminate 99% of all entrained liquids and particles that are 10 microns and larger in siz e. The Model T eparators can be fabricated from carbon steel or stainless steel and are manufactured in accordance with the AME ode ection VIII, Division I. A A B G B G PIPE IZE 1 1/ 1 1/ 2 1/ THREADED OR OKET WELD & THREADED OR OKET WELD 150 PIG PHONE FAX PIG WEIGHT UTOMER PEIFIATION A A B G TD WEIGHT WEIGHT 6 3/ 10 1/ 10 1/ 1 5 9/ / 10 1/ 10 1/ 1 5 9/ / 11 1/ 12 1/ 6 5/ / 11 1/ 12 1/ 6 5/ / / 5 3/ / 5 3/ 1 1/ / 1 1/ / 1 1/ / / / 2 1/ / 2 1/ / / / / / * DIMENION AND WEIGHT

11 PRODUT, IN. TYPE: Horizontal flow installations only MODEL: DryFlo T Moisture eparator TB No Date 199 Gas, laden with moisture, enters the inlet of the separ ator where a deflector plate directs the flow in a downward centrifugal motion. The entrained moisture is then separated out of the flow by a reduction in velocity. The separated liquid is sent to the outer walls of the separ ator and falls below the reentrainment breaker plate where it is prevented for reentering the flow stream. The addition of a sump area will allow for a liquid holdup capacity. A dry, clean flow then results, exiting upward through the outlet of the separ ator. With correct sizing and proper drainage, these separators are designed to eliminate 99% of all entrained liquids and particles that are 10 microns and larger in siz e. The Model T eparators can be fabricated from carbon steel or stainless steel and are man ufactured in accordance with the AME ode ection VIII, Division I. A B G FOUR ANGLE LEG w/ BAE PLATE OPTIONAL UPPORT KIRT w/ FOUR AE OPENING EQUALLY PAED PIPE IZE 1 1/ 1 1/ 2 1/ A 10 1/ 10 1/ 11 1/ 11 1/ DIMENION AND WEIGHT 150 PIG 500 PIG B G TD WEIGHT WEIGHT 5 9/1 5 9/1 6 5/ 6 5/ 8 5/ 10 3/ 12 3/ / 10 1/ 10 1/ 10 1/ 11 7/ 11 7/ 11 7/ 12 5/ 12 5/ 12 5/ 1 1 1/ 1 1/ 1 1/ 2 1/ 2 1/ * PHONE FAX LIQUID HOLDUP APAITY (UBI FEET)

12 PRODUT, IN. TYPE: Horizontal In/ Vertical Downflow Out MODEL: DryFlo TF Filter eparator TB No Date 214 The ircle Filter eparator is a multistage separator that provides optimal removal of both Liquids and olids from a gas steam. The gas must flow through the filter element. The solid particulate is captured on the surface of the filter, and in the depth filter media. The fine liquid particles flow through the element and coalesce with other liquid particles to form larger particles. These larger particles emerge from the inner core and are carried down stream to the final separation region. The model TF can be fabricated from carbon or stainless steel and are manufactured in accordance with AME ode ection VIII, Division 1. With correct sizing and proper drainage, these separators are designed to eliminate 99% of all entrained liquids and particles that are 1 microns and larger in size. DIMENION AND WEIGHT IZE 1/ 3/ 1 1/4' 1 1/ A B D P(PIG) T ( F) " 4" 5" 6" / 4 1/ 5 9/1 6 5/ 6 5/ 1/ 3/ / PHONE FAX

13 PRODUT, IN. TYPE: Horizontal flow installations only (ast Iron) MODEL: DryFlo T Moisture eparator TB No Date 199 Gas laden with moisture, enters the inlet of the separ ator where a deflector plate directs the flo w in a downward centrifugal motion. The entrained moisture is then separated out of the flow by a reduction in velocity. The separated liquid is sent to the outer walls of the separ ator and falls below the reentrainment breaker plate where it is pre vented from reentering the flow stream. A dry, clean flow then results, exiting upward through the outlet of the separ ator. With correct sizing and proper drainage, these separators are designed to eliminate 99% of all entr ained liquids and particles that are 10 microns and larger in siz e. DIMENION AND WEIGHT IZE 1 1/ 2 1/ FLG D A B P(PIG) T ( F) 7 1/ 8 1/ 9 3/ / 11 5/ / 19 1/ 4 3/ 4 3/ 4 3/ 4 3/ 5 3/ 5 1/ 6 5/ 7 3/ 9 1/ 11 1/ 1 1/ 1 1/ 1 1/ PHONE FAX

14 PRODUT, IN. TYPE: Horizontal MODEL: DryFlo Moisture eparator TB No Date 199 DryFlo model separators are cast iron which meets ATMA278 lass 35 standards. All pressure parts are designed and built to meet AME ode, ection VIII for unfired pressure vessels. Removes over 99% of all particulates in excess of 10 microns in size over a wide range of flow rates. ompact trap design features stainless steel moving parts and permits easy access for service. Manual draining is also available. Unit is lightweight can be supported by just the piping. Optional heating element prevents freezing. : F (Non ode) : F (Non ode) : 150 PIG (Non ode) DIMENION AND WEIGHT A B D E F WEIGHT PHONE FAX

15 PRODUT, IN. TYPE: Horizontal or Vertical downflow installations MODEL: DryFlo L1 oalescer TB No Date 199 The Model L1 oalescereparators are designed for horizontal or vertical down flow installations. These separators use a two stage separation process. tage one utilizes a wire mesh pad that increases the siz e of the droplets as they travel through the pad. In stage two the stainless steel eparating Tuyere Diffuser causes the stream to enter a controlled centrifugal flow. Due to the centrifugal motion, entrained liquids and solids are directed to the outer w alls of the separator. Reentrainment breaker plates create a quiet iner t zone to prevent liquid from reentering the flow stream once separation has taken place. With correct sizing and proper drainage, these separators are designed to eliminate 99% of all entr ained liquids and particles that are 5 microns and larger in siz e. The Model L1 oalescereparators can be fabricated from carbon steel or stainless steel and are man ufactured in accordance with AME ode ection VIII Division I. As a standard, these separators come with the AME ode tamp. PIPE IZE 2 1/ PREURE 150 PI / DIMENION AND WEIGHT A B TD WEIGHT / 8 5/ 10 3/ 12 3/ / 1 1/ 1 1/ 2 1/ 2 1/ DIMENION AN BE LIGHTLY DIFFERENT AT HIGHER PREURE AND TEMPERATURE AND ARE AVAILABLE UPON REQUET. PHONE FAX

16 PRODUT, IN. TYPE: Horizontal In / Vertical Upflow installations only MODEL: DryFlo L5 oalescereparator TB No Date 199 The Model L5 oalescereparators are designed f or horizontal inlet and v ertical up flow installations. These separators use a two stage separation process. tage one utilizes a wire mesh pad that increases the siz e of the droplets as they travel through the pad. In stage two a stainless steel eparating Tuyere Diffuser causes the stream to enter a controlled centrifugal flow. Due to the centrifugal motion, entrained liquids and solids are directed to the outer walls of the separator. Reentrainment breaker plates create a quiet iner t zone to prevent liquid from reentering the flow stream once separation has taken place. With correct sizing and proper drainage, these separators are designed to eliminate 99% of all entrained liquids and particles that are 5 microns and larger in siz e. Model L5 oalescereparators can be fabricated from carbon steel or stainless steel and are manufactured in accordance with AME ode ection VIII Division I. As a standard, these separators come with the AME ode tamp. PIPE IZE 2 1/ A PREURE 150 PI / DIMENION AND WEIGHT B E TD / 10 3/ / 1 1/ 1 1/ 2 1/ 2 1/ PHONE FAX WEIGHT lbs DIMENION AN BE LIGHTLY DIFFERENT AT HIGHER PREURE AND TEMPERATURE AND ARE AVAILABLE UPON REQUET.

17 PRODUT, IN. TYPE: Horizontal In / Vertical downflow installations only MODEL: DryFlo L6 oalescereparator TB No Date 199 The Model L6 oalescereparators are designed for a horizontal inlet and and vertical up flow installations. These separators use a two stage separation process. tage one utilizes a wire mesh pad that increases the size of the droplets as they travel through the pad. In stage two a stainless steel eparating Tuyere Diffuser causes the stream to enter a controlled centrifugal flow. Due to the centr ifugal motion, entrained liquids and solids are directed to the outer walls of the separator. Reentrainment breaker plates create a quiet zone to prevent liquid from reenter ing the flow stream once separation has taken place. With correct sizing and proper drainage, these separators are designed to eliminate 99% of all entrained liquids and particles that are 5 microns and larger in siz e. Model L6 oalescereparators can be fabricated from carbon steel or stainless steel and are manufactured in accordance with AME ode ection VIII Division I. As a standard, these separators come with the AME ode tamp. PIPE IZE 2 1/ A DIMENION AND WEIGHT B E TD / 8 5/ 10 3/ 12 3/ / 1 1/ 1 1/ / 2 1/ 2 1/ PHONE FAX WEIGHT lbs DIMENION AN BE LIGHTLY DIFFERENT AT HIGHER PREURE AND TEMPERATURE AND ARE AVAILABLE UPON REQUET.

18 APPLIATION For use to remove entrained air. IRLE PRODUT, IN. PEIFIATION Air eparator shall be arbon teel constr uction AME ode tamped for maximum working pressure to 150 psig. Vessel is designed for a maximum temperature of 450 F. Pipe connections are for sizes thru 2 1/ and ANI RF flanges for and larger. FEATURE Tangential design results in smaller unit requirement. It provides air free flow which protects against damage and system noise, and helps to prevent water logged plain steel expansion tanks. MODEL: A Air eparator TB No Date 101 TANDARD These vessels are designed in accordance with AME ode ection VIII, Div. 1 and can be AME ode tamped for 150 psig. OPTION tainless teel construction. Working Pressures to 3000PIG Pipe connections to 2 pecial exterior finish For options specification and pricing consult ircle Products, Inc. DIMENION AND WEIGHT INLET / OUTLET A B D E F G 2 1/ / 16 5/ 19 3/ 21 3/ 21 3/ / / / 19 1/ 19 1/ 39 3/ 39 3/ / / / 6 1/ 6 3/ 9 1/ 9 1/ 13 1/ 13 1/ / 32 1/ / 12 3/ 12 3/ /1 4 1/1 3 3/ 4 1/ 3 3/ 6 1/ 5 3/1 9 1/ 8 1/ 10 3/1 12 1/ 13 5/ / 1 1/ 1 1/ 1 1/ 1 1/ WEIGHT LB PHONE FAX