ALAKA TEEL CO. PRODUCT REFERENCE GUIDE
|
|
|
- Elisabeth Hood
- 5 years ago
- Views:
Transcription
1 ALAKA TEEL CO. PRODUCT REFERENCE GUIDE Serving Alaska since 1982
2 Our mission is to build loyal partnerships with our customers through knowledge, a commitment to success, and leading our industry with service-driven quality.
3 STAINLESS STEEL INDEX PAGE Angle...2 Description...1 Plate Weights...8 Rectangular Round Sheet...7 JULY 2012 Steel & Aluminum Distributors for Alaska
4
5 types 304 and 304L - Sheets, Plates, Bars, Angles UNS S30400, Type 304 is the basic 18-8 chromium-nickel stainless steel. It combines excellent mechanical properties with remarkable resistance to many corrosive agents encountered in domestic and industrial use. It is non-magnetic in the annealed condition and not hardenable by heat treatment. Both hardness and tensile strength can be increased by cold working. This is an electric-furnace product manufactured to meet the exacting standards of the aircraft industry. The analysis of Type 304 is similar to that of Type 304L except that Type 304L is modified by lowered carbon content. This provides good resistance to corrosion in welded construction where subsequent heat treatment is not practicable. Bars and Plates are available not only in the regular Type 304 analysis, but also in an extra low carbon analysis Type 304L. The advantage of this analysis is that it precludes any harmful precipitation in the F range, such as might otherwise occur in welding heavier sections. analysis C Mn P S Si Cr Ni Cu Mo Max. Max. Max. Max. Max. Max. Max / / L / / specifications - The following specifications are generally applicable: Sheets & Plates: AMS 5513, ASTM A 167, ASTM A 240 Bars: AMS 5639, ASTM A 276, ASTM A 479 applications - Used where corrosion resistance and good mechanical properties are primary requirements. These grades are widely accepted in such industries as dairy, beverage, and other food products where the highest degree of sanitation and cleanliness is of prime importance. Parts for handling acetic, nitric, and citric acids, organic and inorganic chemicals, dyestuffs, crude and refined oils, etc., are fabricated from this material. Because of its lack of magnetism it is highly desirable for instruments. It is also widely used for architectural trim. Type 304 sheets are used in aircraft applications where corrosion resistance is required, but where gas or arc welding and elevated temperatures are not involved. Type 304L, as noted above, finds particular use in applications requiring welding. corrosion resistance - Types 304 and 304L show good resistance to corrosion. They are highly resistant to strong oxidizing acids, such as nitric acid, and resist attack by a wide variety of organic and inorganic chemicals. Maximum corrosion resistance is obtained in the annealed condition. Intergranular corrosion may occur when material is heated within or cooled through the range of 800 to 1500 F. resistance to scaling - Excellent scale resistance at temperatures up to 1600 F in continuous service. Chromium-nickel grades have a high coefficient of expansion, which should be considered in designing. mechanical properties - Applicable specifications require the following properties of sheets in the annealed condition: Tensile Min. Elongation in 2 Strength.015 Thick.016 Thick.031 Thick (psi) and Under to.030 and Over Type ,000 Max. 40% 40% 40% In practice, annealed sheets and plates will average as follows: Tensile Strength Yield Strength Elongation Rockwell B (psi) (psi) in 2 hardness 90,000 40,000 50% 85 JULY 2012 Steel & Aluminum Distributors for Alaska 1
6 machinability - Types 304 and 304L have a machinability rating of approximately 45% with 1212 rated as 100%. Surface cutting speed on automatic screw machines is approximately 75 feet per minute. weldability - Easily welded by all the commercial processes except forging or hammer welding. The resulting weld has good toughness and ductility. Annealing is recommended after welding to maintain maximum corrosion resistance. forming - These grades have very good drawing and stamping properties. Forging - Forge between 2100 and 2350 F. Do not forge below 1700 F. Annealing - Annealing range is between 1850 and 2050 F. Cool rapidly. Water should be used for heavier sections; air for lighter sections. The stress relieving range is between 400 and 750 F. ANGLE - STAINLESS STEEL TYPE 304 AND Random Lengths Size Pounds Pounds Per in Inches Per Foot 20 Length 3/4 x 3/4 x 1/ x 1 x 1/ x 1 x 3/ x 1 x 1/ /4 x 1 1/4 x 1/ /4 x 1 1/4 x 3/ /4 x 1 1/4 x 1/ /2 x 1 1/2 x 1/ /2 x 1 1/2 x 3/ /2 x 1 1/2 x 1/ x 2 x 1/ x 2 x 3/ x 2 x 1/ x 2 x 5/ x 2 x 3/ /2 x 2 1/2 x 3/ /2 x 2 1/2 x 1/ /2 x 2 1/2 x 5/ /2 x 2 1/2 x 3/ x 3 x 1/ x 3 x 5/ x 3 x 3/ /2 x 3 1/2 x 1/ /2 x 3 1/2 x 5/ /2 x 3 1/2 x 3/ x 4 x 1/ x 4 x 5/ x 4 x 3/ Steel & Aluminum Distributors for Alaska JULY 2012
7 rectangular STAINLESS STEEL Bar TYPE Random Lengths Thickness Width Wght/ Wght/ in Inches in Inches Lin Ft. 12 Lgth 1/8 1/ / / / / / /16 1/ / / / / / / /4 1/ / / / / / / /16 3/ / Standard sizes also available in low carbon grade, (304-L). For sizes not shown, please contact our office. JULY 2012 Steel & Aluminum Distributors for Alaska 3
8 rectangular STAINLESS STEEL Bar TYPE 304 (Continued) Random Lengths Thickness Width Wght/ Wght/ in Inches in Inches Lin Ft. 12 Lgth 3/8 1/ / / / / / /2 3/ / / / / / / /8 3/ / / / / Standard sizes also available in low carbon grade, (304-L). For sizes not shown, please contact our office. 4 Steel & Aluminum Distributors for Alaska JULY 2012
9 round STAINLESS STEEL Bar TYPE 304/316 Size Dec. Lbs/ Inches Equiv. Ft. 1/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / JULY 2012 Steel & Aluminum Distributors for Alaska 5
10 round STAINLESS STEEL Bar TYPE 304/316 (Continued) Size Dec. Lbs/ Inches Equiv. Ft. 1 9/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Steel & Aluminum Distributors for Alaska JULY 2012
11 STAINLESS STEEL sheet TYPE 304L/304 Gauge Lbs. Per Est. Lbs. and Size Square Per in Inches Foot Sheet 22 Gauge (.0291) 48 x x Gauge (.0355) 48 x x x Gauge (.048) 36 x x x Gauge (.0595) 36 x x x x x Gauge (.075) 36 x x x x x x x x Gauge (.090) 48 x ALASKA STEEL CO. *May be slightly magnetic when cold worked. Cold Rolled, Annealed No. 2B Finish Can also be furnished: No. 3 or No. 4 Finish Polished One or Two Sides Non-Magetic* Paper Interleaved or Vinyl Masked A.S.T.M. A480/A240 A.S.T.M. A666 A.S.T.M. A262 Prac E ASME SA-240 AMS 5511 Gauge Lbs. Per Est. Lbs. and Size Square Per in Inches Foot Sheet 12 Gauge (.105) 48 x x x x x x x x Gauge (.120) 48 x x x x x x Gauge (.135) 48 x x x x x x x x Gauge (.165) 48 x x Gauge (.1874) 48 x x x JULY 2012 Steel & Aluminum Distributors for Alaska 7
12 stainless plate weights Thickness in Inches Fraction Decimal Pounds per Square Foot Pounds per Square Inch Thickness in Inches Fraction Decimal Pounds per Square Foot Pounds per Square Inch 3/ / / / / / / / / / / / / / / / / / / / / / / / Steel & Aluminum Distributors for Alaska JULY 2012
13 ALUMINUM INDEX PAGE Angle...15, 16 Bar...22, 23 Beam...19, 20 Channel Continuous Hinge...31, 32 Hollaender Fittings...27, 28 Marine Extrusions...29, 30 Pipe...25, 26 Pipe Fittings (threaded/weld-on)...inquire Rod...24 Sheet and Plate Square and Rectangular Tubing...33 Tee...21 Tread Plate...13, 14 Useful Information JULY 2012 Steel & Aluminum Distributors for Alaska
14
15 JULY 2012 Steel & Aluminum Distributors for Alaska 9
16 .100 x 60 x x 60 x x 48 x x 48 x x 48 x x 48 x x 60 x x 60 x x 48 x x 48 x x 48 x x 48 x x 60 x Steel & Aluminum Distributors for Alaska JULY 2012
17 .125 x 48 x B JULY 2012 Steel & Aluminum Distributors for Alaska 11
18 Steel & Aluminum Distributors for Alaska JULY 2012
19 H32 Aluminum tread plate JULY 2012 Steel & Aluminum Distributors for Alaska 13
20 The ultimate and yield strengths of alloy 5086-H34, along with its elongation properties, are essentially the same as those for alloy 6061-T6. But because 5086-H34 is a 5XXX alloy, fatigue strength is 50 percent higher and it exhibits better formability. So alloy 5086-H34 tread plate can be substituted for alloy 6061-T6 tread plate with complete confidence in most situations. 14 Steel & Aluminum Distributors for Alaska JULY 2012
21 JULY 2012 Steel & Aluminum Distributors for Alaska 15
22 Steel & Aluminum Distributors for Alaska JULY 2012
23 JULY 2012 Steel & Aluminum Distributors for Alaska 17
24 C B Steel & Aluminum Distributors for Alaska JULY 2012
25 B C JULY 2012 Steel & Aluminum Distributors for Alaska 19
26 B C 20 Steel & Aluminum Distributors for Alaska JULY 2012
27 Aluminum sheet and plate stocked in 48 to 96 widths JULY 2012 Steel & Aluminum Distributors for Alaska 21
28 Steel & Aluminum Distributors for Alaska JULY 2012
29 JULY 2012 Steel & Aluminum Distributors for Alaska 23
30 extruded round rod Steel & Aluminum Distributors for Alaska JULY 2012
31 6063-T6 extruded aluminum pipe JULY 2012 Steel & Aluminum Distributors for Alaska 25
32 26 Steel & Aluminum Distributors for Alaska JULY 2012
33 SPEED-RAIL /NU-RAIL Structural Fittings And Flanges For use with Aluminum or Iron pipe to construct railings, scaffolds, enclosures, truck racks, storage racks or in structural applications. Stocked in Standard Iron Pipe Sizes, 3/4-in., 1-in., 1-1/4-in. 1-1/2-in., 2-in. No. 3 Elbow No. 3AE Adjustable Elbow No. 5 Tee No. 7 Cross No. 9 Side-Outlet Elbow No. 17 Adjustable Elbow or Tee No. 19 Adjustable Cross No. 10 Cross No. 20 Outside Corner JULY 2012 Steel & Aluminum Distributors for Alaska 27
34 No. 45 SBC Flange No. 48 Flange No. 50 Flange No. 52E Flange No. 60 Plug Many more styles and configurations available. Call our sales department for a complete brochure. 28 Steel & Aluminum Distributors for Alaska JULY 2012
35 Designed for the bottom (flat bottom) and gunnel rail for aluminum skiff type design. hat section R R DIA.219 R t lbs. 25 Long 13.0 lbs. 25 Long JULY 2012 Steel & Aluminum Distributors for Alaska 29
36 t6 30 Steel & Aluminum Distributors for Alaska JULY 2012
37 With Fullhard Aluminum Pins 72 Length *With Aluminum Pins / JULY 2012 Steel & Aluminum Distributors for Alaska 31
38 Sample of stocked extrusions 32 Steel & Aluminum Distributors for Alaska JULY 2012
39 6063-T6 SQUARE EXTRUDED ALUMINUM TUBE Sharp Corners Lengths T6 SQUARE EXTRUDED ALUMINUM TUBE Round Corners - 20 Lengths T6 RECTANGULAR EXTRUDED ALUMINUM TUBE Sharp Corners Lengths JULY 2012 Steel & Aluminum Distributors for Alaska 33
40 GENERAL ALLOY CHARACTERISTICS ALUMINUM 34 Steel & Aluminum Distributors for Alaska JULY 2012
41 JULY 2012 Steel & Aluminum Distributors for Alaska 35
42 36 Steel & Aluminum Distributors for Alaska JULY 2012
43 JULY 2012 Steel & Aluminum Distributors for Alaska 37
44 38 Steel & Aluminum Distributors for Alaska JULY 2012
45 JULY 2012 Steel & Aluminum Distributors for Alaska 39
46 40 Steel & Aluminum Distributors for Alaska JULY 2012
47 JULY 2012 Steel & Aluminum Distributors for Alaska 41
48 42 Steel & Aluminum Distributors for Alaska JULY 2012
49 JULY 2012 Steel & Aluminum Distributors for Alaska 43
50 44 Steel & Aluminum Distributors for Alaska JULY 2012
51 0.250 JULY 2012 Steel & Aluminum Distributors for Alaska 45
52 46 Steel & Aluminum Distributors for Alaska JULY 2012
53 JULY 2012 Steel & Aluminum Distributors for Alaska 47
54 48 Steel & Aluminum Distributors for Alaska JULY 2012
55 STEEL AND MISCELLANEOUS INDEX PAGE A-36, A-572, A-992 Product Description...49, 50, 51 Abrasion Resisting Plate (Hardox)...98, 99 Angles Bar Gate (Steel and Fiberglass)...110, 111 Channels Continuous Hinge... (see Aluminum) Expanded Metal Flat Bar , 91 Floor Plate High Strength Sheet & Plate...96, 97 I Beams...60 Junior Beams...57 Pipe and Tubing Plate (UM and A-36) Plate Tolerances Pressure Vessel Plate...94, 95 Re-Bar and Welded Wire Fabric...73, 74 Rounds (A-36)...70, 71 Rounds & Square (CF and Alloy Bars) Safety Grating...115, 116 Sheet Sheet Tolerance...87 Ship Channel...59 Square (A-36)...72 Strip...65 Wide Flange Beam Useful Information JULY 2012 Steel & Aluminum Distributors for Alaska
56
57 We also carry structurals that meet ASTM A-572 grade 50 and beams to ASTM A-992. JULY 2012 Steel & Aluminum Distributors for Alaska 49
58 ASTM A572 Structural Shapes Chemical Requirements (Heat Analysis) Grade Grade Carbon max, % Manganese max, % % 42 [290] [345] [380] [415] [450] Silicon Grade Shapes to 426 lb/ft [634 kg/m] Sheet Piling, Bars, Zees, and Rolled Tees max % range % 42 [290] [345] [380] [415] 0.40 N/A 65 [450] 0.40 N/A Alloy Content Elements Heat Analysis, % Columbium Vanadium Tensile Requirements Phosphorus max, % Shapes Over 426 lb/ft [634 kg/m] Sulfur, max, Yield Point, min Tensile Strength, min Minimum Elongation, % ksi [MPa] ksi [MPa] in 8 in. in 2 in. [200 mm] [50 mm] 42 [290] 42 [290] 60 [415] [345] 50 [345] 65 [450] [380] 55 [380] 70 [485] [415] 60 [415] 75 [520] [450] 65 [450] 80 [550] Steel & Aluminum Distributors for Alaska JULY 2012
59 ASTM A-992 Structural Shapes This designation was implemented in 1998 to cover beam sections for use in building frames, bridges or for general structural purposes to allow engineering closer tensile and yield design criteria than ASTM A-36. Chemical Requirements (Heat Analysis) Element Composition, % Carbon, max 0.23 Manganese 0.50 to 1.50 A Silicon, max 0.40 Vanadium, max 0.11 B,C Columbium, max 0.05 B Phosphorus, max Sulfur, max Copper, max 0.60 Nickel, max 0.45 Chromium, max 0.35 Molybdenum, max 0.15 A Provided that the ratio of manganese to sulfur is not less than 20 to 1, the minimum limit for manganese for Group 1 shapes shall be 0.30%. B The sum of columbium and vanadium shall not exceed 0.15%. C When vanadium is added as the only nitrogen-binding element, nitrogen shall be reported and the ratio of vanadium to nitrogen shall be 4 to 1 or higher if the nitrogen content is greater than 0.012%. Tensile Requirements Tensile strength, min kis [MPa] 65 [450] Yield point, ksi [MPa] 50 to 65 [345 to 450] Yield to tensile ratio, max 0.85 Elongation in 8 in. [200 mm], min, % 18 Elongation in 2 in. [50 mm], min, % 21 JULY 2012 Steel & Aluminum Distributors for Alaska 51
60 52 Steel & Aluminum Distributors for Alaska JULY 2012
61 Production sawing with 27 width cut capacity JULY 2012 Steel & Aluminum Distributors for Alaska 53
62 54 Steel & Aluminum Distributors for Alaska JULY 2012
63 JULY 2012 Steel & Aluminum Distributors for Alaska 55
64 56 Steel & Aluminum Distributors for Alaska JULY 2012
65 JULY 2012 Steel & Aluminum Distributors for Alaska 57
66 and A-572 grade 50 20, 40, 50 and 60 Feet 58 Steel & Aluminum Distributors for Alaska JULY 2012
67 10 x 3-1/ /2* / x 3-1/ JULY 2012 Steel & Aluminum Distributors for Alaska 59
68 and A-572 grade Steel & Aluminum Distributors for Alaska JULY 2012
69 JULY 2012 Steel & Aluminum Distributors for Alaska 61
70 Steel & Aluminum Distributors for Alaska JULY 2012
71 JULY 2012 Steel & Aluminum Distributors for Alaska 63
72 Steel & Aluminum Distributors for Alaska JULY 2012
73 JULY 2012 Steel & Aluminum Distributors for Alaska 65
74 66 Steel & Aluminum Distributors for Alaska JULY 2012
75 JULY 2012 Steel & Aluminum Distributors for Alaska 67
76 68 Steel & Aluminum Distributors for Alaska JULY 2012
77 JULY 2012 Steel & Aluminum Distributors for Alaska 69
78 70 Steel & Aluminum Distributors for Alaska JULY 2012
79 JULY 2012 Steel & Aluminum Distributors for Alaska 71
80 72 Steel & Aluminum Distributors for Alaska JULY 2012
81 1-1/8 1-1/4 1-3/8 Rebar stocked in 60 lengths JULY 2012 Steel & Aluminum Distributors for Alaska 73
82 Common Stock Styles of Welded Wire Fabric new DESIGNATION (BY W-Number) STYLE DESIGNATION OLD DESIGNATION (BY STEEL WIRE GAUGE) steel area sq. in. per ft. LONGIT. TRANS. WEIGHT APPROX. LBS. PER 100 S.F. ROLLS 6x6 W1.4xW1.4 6x6 10x SHEETS 6x6 W1.4xW1.4 6x6 10x x6 W2.1xW2.1 6x6 8x x6 W2.9xW2.9 6x6 6x x6 W4.0xW4.0 6x6 4x x6 W5.5xW5.5 6x6 2x2** x4 W4.0xW4.0 4x4 4x *Exact W-number size for 2 gauge is W5.4. Wire Size Designation The new method of designating wire sizes is a complete departure from the steel wire gauge system previously used. Shown above is a comparison of W and D number wire sizes to nominal decimal diameters and to the steel wire gauge system. Cross-sectional area is the basic element used in specifying wire size. Smooth wire sizes are specified by the letter W followed by a number indicating the cross-sectional area of the wire in hundredths of a square inch. For example: W16 denotes a smooth wire with cross-sectional area of 0.16 sq. in.; W5.5 identifies a smooth wire with cross-sectional area of sq. in., etc. Similarly, deformed wire sizes are specified by the letter D followed by a number which indicates hundredths of a square inch. For example: D10 is a deformed wire with a cross-sectional area of 0.10 sq. in. 74 Steel & Aluminum Distributors for Alaska JULY 2012
83 Automated rebar line JULY 2012 Steel & Aluminum Distributors for Alaska 75
84 Outside 7-1/2 and 10 ton crane bays 76 Steel & Aluminum Distributors for Alaska JULY 2012
85 JULY 2012 Steel & Aluminum Distributors for Alaska 77
86 Our modern delivery fleet 78 Steel & Aluminum Distributors for Alaska JULY 2012
87 JULY 2012 Steel & Aluminum Distributors for Alaska 79
88 1/2 x 12 mechanical plate shear 80 Steel & Aluminum Distributors for Alaska JULY 2012
89 Per Length JULY 2012 Steel & Aluminum Distributors for Alaska 81
90 A Steel & Aluminum Distributors for Alaska JULY 2012
91 A1011 Plate Bay JULY 2012 Steel & Aluminum Distributors for Alaska 83
92 A Steel & Aluminum Distributors for Alaska JULY 2012
93 Our high definition plasma with 8 x20 table JULY 2012 Steel & Aluminum Distributors for Alaska 85
94 86 Steel & Aluminum Distributors for Alaska JULY 2012
95 JULY 2012 Steel & Aluminum Distributors for Alaska 87
96 88 Steel & Aluminum Distributors for Alaska JULY 2012
97 JULY 2012 Steel & Aluminum Distributors for Alaska 89
98 90 Steel & Aluminum Distributors for Alaska JULY 2012
99 JULY 2012 Steel & Aluminum Distributors for Alaska 91
100 92 Steel & Aluminum Distributors for Alaska JULY 2012
101 260 High Definition Plasma Burning JULY 2012 Steel & Aluminum Distributors for Alaska 93
102 /.40.15/.40.15/.40.15/.40.15/.40.15/.40.15/.40.15/ Steel & Aluminum Distributors for Alaska JULY 2012
103 75,000 90,000 90,000 Class 1 4 Class 1. A537 Class 1 1-1/2 1-1/2 to / /2 2-1/2 to 4 70,000/90,000 65,000/85,000 45,000 JULY 2012 Steel & Aluminum Distributors for Alaska 95
104 Specifications: The listed steels are an open hearth low alloy steel to ASTM Specs. A-588-Grade A, ASTM A-572 Grade 50 and ASTM A-441. Our flexible buying policy normally enables us to supply any trade name or its ASTM equivalent specification. Our A-572 Grade 50 is ordered with a tested charpy V-notch at -50 F for low temperature applications Steel & Aluminum Distributors for Alaska JULY 2012
105 JULY 2012 Steel & Aluminum Distributors for Alaska 97
106 Alaska Steel is the distributor of Hardox abrasion resisting wear plates. This product has excellent through hardness and, because of its low carbon content, can be easily welded and formed. Lining dump boxes, excavation equipment blades and buckets, and conveyor wear areas are just a few applications. Welding and fabrication information is available on request. Hardox 400 chemical composition Typical values Thickness Mn Cr Ni Mo inch C Si max max max max B CE* 3 /16-3 /4.10/.20.10/ / ( 3 /4)-1 1 /4.10/.20.10/ / (1 1 /4)-2.10/.20.10/ / (2 )-3.15/.26.10/ / * Carbon equivalent CE = C + Mn + Cr + Mo + V + Cu + Ni hardness HB. mechanical properties Yield strength Tensile strength Elongation A 5 ksi ksi % 145* * HARDOX 400 can be supplied with a guaranteed yield strength of 130 ksi. impact properties Charpy-V, longitudinal specimen 40 F Typical value 22 ft. lbs Hardox 500 chemical composition Typical values Thickness inch C Si Mn Cr Mo B CE 1 /4-3.20/.30.10/ max 1.0 max 0.5 max.001/ /.59 hardness HB (>2 thickness slightly lower value) mechanical properties Yield strength Tensile strength Elongation A 5 ksi ksi % Typical values impact properties Charpy-V, longitudinal specimen 40 F Typical values 15 ft. lbs 98 Steel & Aluminum Distributors for Alaska JULY 2012
107 Custom shape burning to minimize wastage JULY 2012 Steel & Aluminum Distributors for Alaska 99
108 100 Steel & Aluminum Distributors for Alaska JULY 2012
109 JULY 2012 Steel & Aluminum Distributors for Alaska 101
110 102 Steel & Aluminum Distributors for Alaska JULY 2012
111 Ornamental tubing stored inside to minimize rust JULY 2012 Steel & Aluminum Distributors for Alaska 103
112 Nominal Size Wall Lbs. per In. In. Foot 1/2 x 1/ /8 x 5/ /4 x 3/ x /4 x 1-1/ /2 x 1-1/ /4 x 1-3/ x Our private railsiding serviced by overhead crane or forklift 104 Steel & Aluminum Distributors for Alaska JULY 2012
113 Nominal Size Wall Lbs. per Nominal Size Wall Lbs. per In. In. Foot In. In. Foot 2 X /2 x 2-1/ x /2 x 3-1/ x /2 x 4-1/ x x x x x x x x JULY 2012 Steel & Aluminum Distributors for Alaska 105
114 Nominal Size Wall Lbs. per In. In. Foot 1-1/2 x x x 1-1/ /2 x 1-1/ x x 1-1/ Vast inventory of expanded metal 106 Steel & Aluminum Distributors for Alaska JULY 2012
115 Nominal Size Wall Lbs. per Nominal Size Wall Lbs. per In. In. Foot In. In. Foot 3 X x x x x x x x x x x x x x x x x x x JULY 2012 Steel & Aluminum Distributors for Alaska 107
116 Steel & Aluminum Distributors for Alaska JULY 2012
117 10XH XH JULY 2012 Steel & Aluminum Distributors for Alaska 109
118 110 Steel & Aluminum Distributors for Alaska JULY 2012
119 Pultruded Fiberglass the sensible choice Low Installation Costs Weighing considerably less than conventional metal gratings, fiberglass grating is easier and less expensive to transport, install, and remove. Only simple hand tools are required for installation and removal, eliminating the need for costly equipment and labor costs associated with heavy lifting, cutting, and welding. Slip-Resistant Surface Strategically angled lower I-bars allow for easy fluid runoff which aids self-cleaning. Patented Flush-Top Cross-Rod and Bearing Bar Topped by a standard epoxy grit slip-resistant surface, this system mechanically locks cross rods and bearing bars together, increasing unidirectional strength and enabling easy fabrication. Non-Conductivity Amico-Seasafe s glass and resin formulations are non-sparking and create a safety barrier for personnel in electrical applications, including electrical work platforms and fencing around high-voltage equipment. In addition, its nonmagnetic properties make it transparent to electromagnetic waves in applications involving radio, television and microwave installations. A coarse epoxy grit is bonded to the walking surfaces of all Gator Deck pultruded grating and Gator Deck stair treads for improved traction, especially in high-traffic areas. Two-Part Mechanical Locking Cross-Rod A continuous pultruded groove rod interlocked with spacer bar provide a mechanical lock at each bearing bar. This interlocking design increases the support and stability of Gator Deck under extreme loads. Reliability You can count on Gator Deck s superior ability to fight the elements with its durable light-weight construction and quality. Self-Draining JULY 2012 Steel & Aluminum Distributors for Alaska 111
120 Weight Strand Thickness ga. 4 x Steel & Aluminum Distributors for Alaska JULY 2012
121 Weight Strand Thickness Note: 1. Opening Size is the approximate inside opening of diamond-shaped holes. 2. Flattened sizes are expanded from heavier gage and flattened to the lighter gage, e.g. 3/4 x was 14 ga. sheet expanded and flattened to 16 ga. JULY 2012 Steel & Aluminum Distributors for Alaska 113
122 4 x Steel & Aluminum Distributors for Alaska JULY 2012
123 JULY 2012 Steel & Aluminum Distributors for Alaska 115
124 A-IS 3200-A-IS 4200-A-IS 5200-A-IS 8200-A-IS Steel & Aluminum Distributors for Alaska JULY 2012
125 JULY 2012 Steel & Aluminum Distributors for Alaska 117
126 118 Steel & Aluminum Distributors for Alaska JULY 2012
127 JULY 2012 Steel & Aluminum Distributors for Alaska 119
128 c a 90 b a 2 + b 2 = c Steel & Aluminum Distributors for Alaska JULY 2012
129 CONVERSION FACTORS FOR WEIGHTS AND MEASURES U.S. TO METRIC Pounds (Avoirdupois) X = Kilograms Tons (2000 pounds) X = Metric Tons Tons (2240 pounds) X = Metric Tons Inches X = Centimeters Inches X = Millimeters Feet X = Meters Square Inches X = Square Centimeters Square Feet X.0929 = Square Meters Cubic Inches X = Cubic Centimeters Cubic Feet X = Cubic Meters Pounds per Foot X = Kilos per Meter Ounces per Square Foot X = Grams per Square Centimeter Ounces per Square Foot X = Grams per Square Meter Pounds per Square Inch X = Kilograms per Square Centimeter Pounds per Square Inch X = Kilograms per Square Millimeter Pounds per Square Foot X = Kilograms per Square Meter Pounds per Cubic Foot X = Kilograms per Cubic Meter METRIC TO U.S. Kilograms X = Pounds (Avoirdupois) Metric Tons X = Tons (2000 pounds) Metric Tons X = Tons (2240 pounds) Centimeters X.3937 = Inches Millimeters X = Inches Meters X = Feet Square Centimeters X.155 = Square Inches Square Meters X = Square Feet Cubic Centimeters X = Cubic Inches Cubic Meters X = Cubic Feet Kilograms Per Meter X = Pounds per Foot Grams per Square Centimeter X = Ounces per Square Ft Grams per Sq Meter X = Ounces per Square Ft Kilograms per Square Centimeter X = Pounds per Sq Inch Kilograms per Square Millimeter X = Pounds per Sq Inch Kilos per Sq Meter X = Pounds per Sq Inch Kilos per Cubic Meter X = Pounds per Cubic Foot JULY 2012 Steel & Aluminum Distributors for Alaska 121
130 122 Steel & Aluminum Distributors for Alaska JULY 2012
131 JULY 2012 Steel & Aluminum Distributors for Alaska 123
132 124 Steel & Aluminum Distributors for Alaska JULY 2012
133 JULY 2012 Steel & Aluminum Distributors for Alaska 125
134 Heating steels to approximately 100 F above the critical temperature range followed by cooling to below that range in still air at ordinary temperatures. This heat treat operation is used to erase previous heat treating results in carbon steels and to produce a uniform grain structure in forged and cold worked steel parts. 126 Steel & Aluminum Distributors for Alaska JULY 2012
135 JULY 2012 Steel & Aluminum Distributors for Alaska 127
136 128 Steel & Aluminum Distributors for Alaska JULY 2012
137 JULY 2012 Steel & Aluminum Distributors for Alaska 129
138 130 Steel & Aluminum Distributors for Alaska JULY 2012
139 JULY 2012 Steel & Aluminum Distributors for Alaska 131
140
141 PHONE LIST Anchorage 1200 W. Dowling Rd. Anchorage, AK Telephone (907) Fax (907) Toll Free Fairbanks 2800 South Cushman Fairbanks, AK Telephone (907) Fax (907) Kenai 205 Trading Bay Rd. Kenai, AK Telephone (907) Fax (907)
The Convenience Stores For Metal
STEEL Data and Specifications 303 Chromium-nickel stainless steel with added sulfur or selenium and phosphorus to improve machinability and non-seizing properties. It is the most free machining of the
STAINLESS STEEL SHEETS
STAINLESS & NICKEL ALLOY CHATHAM STEEL CORPORATION 59 STAINLESS STEEL SHEETS TYPE 04, 04L, 6, 6L No. 2B Finish Cold Rolled, Annealed *No. 2D Finish No. Finish Polished One Side No. 4 Finish Polished One
SPECIFICATION FOR STAINLESS STEEL BARS AND SHAPES
SPECIFICATION FOR STAINLESS STEEL BARS AND SHAPES A02 (Identical with ASTM Specification A 276-97.) 1. Scope 1.1 This specification covers hot-finished or coldfinished bars except bars for reforging (Note
Stainless Steel & Stainless Steel Fasteners Chemical, Physical and Mechanical Properties
Stainless Steel & Stainless Steel Fasteners Chemical, Physical and Mechanical Properties Stainless steel describes a family of steels highly resistant to tarnishing and rusting that contain at least two
Steel Corporation. Standard weights & gauges of Steel
Steel Corporation Standard weights & gauges of Steel STANDARD WEIGHTS AND GAUGES OF STEEL AUBURN COATING OFFICE AND WAREHOUSE 0 Lund Road Auburn, WA 9800 Local Phone (2) 7-070 Toll Free (800) 8-076 FAX
Mechanical Properties - Standard. Standard Mild Steel Studs AWS Type A
General Material Specifications Material Specifications Nelson s studs may be made of one of the following materials, as specified on individual specification sheets. Certificates of chemical analysis
ITEM 442 METAL FOR STRUCTURES
ITEM 442 METAL FOR STRUCTURES 442.1. Description. This Item shall govern for all structural steel, high strength bolts, forgings, steel castings, iron castings, wrought iron, bronze, steel pipe and tubing,
Structural Channels A-36:20-40 LG. Standard Beams
Floor Plates #/Sq. Ft. 14 Ga. 3.75 12 Ga. 5.25 1/8 6.16 3/16 8.71 1/4 11.26 5/16 13.81 3/8 16.37 Plates #/Sq. Ft. 3/16 7.66 1/4 10.21 5/16 12.76 3/8 15.32 7/16 17.87 1/2 20.42 9/16 22.97 5/8 25.52 3/4
SPECIFICATION FOR STAINLESS STEEL BARS AND SHAPES FOR USE IN BOILERS AND OTHER PRESSURE VESSELS
2007 SECTION II, PART A SA-479/SA-479M SPECIFICATION FOR STAINLESS STEEL BARS AND SHAPES FOR USE IN BOILERS AND OTHER PRESSURE VESSELS SA-479/SA-479M (Identical with ASTM Specification A 479/A 479M-04
SPECIFICATION FOR PRECIPITATION-HARDENING NICKEL ALLOY BARS, FORGINGS, AND FORGING STOCK FOR HIGH-TEMPERATURE SERVICE
SPECIFICATION FOR PRECIPITATION-HARDENING NICKEL ALLOY BARS, FORGINGS, AND FORGING STOCK FOR HIGH-TEMPERATURE SERVICE (Identical with ASTM Specification B 637-93a) 1. Scope 1.1 This specification covers
Molybdenum. Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium- Designation: A 387/A 387M 03
Designation: A 387/A 387M 03 Used in USDOE-NE Standards Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium- Molybdenum 1 This standard is issued under the fixed designation A 387/A
TABLE OF CONTENTS. Hot Roll (Angles, Beams, Channels, Flats, Squares, Rounds) 3. Pipe, Pipe Tube, Tube. Sheets & Plates
DRI1529-McNeilus-Revised 12/12/05 12:18 PM Page 1 McNeilus Steel, Inc. TABLE OF CONTENTS Page Hot Roll (Angles, Beams, Channels, Flats, Squares, Rounds) 3 Cold Roll (Flats, Hex, Rounds) 17 Pipe, Pipe Tube,
XI'AN LINKUN STEEL PIPE CO., LTD
Designation: A 334/A 334M 04a Standard Specification for Seamless and Welded Carbon and Alloy-Steel Tubes for Low-Temperature Service 1 This standard is issued under the fixed designation A 334/A 334M;
Standard Specification for Seamless and Welded Carbon and Alloy-Steel Tubes for Low-Temperature Service 1
Designation: A 334/A 334M 04a Standard Specification for Seamless and Welded Carbon and Alloy-Steel Tubes for Low-Temperature Service 1 This standard is issued under the fixed designation A 334/A 334M;
ATI 825 ATI 825. Technical Data Sheet. Nickel-base Alloy INTRODUCTION PRODUCT FORMS SPECIFICATIONS & CERTIFICATES (UNS N08825)
ATI 825 Nickel-base (UNS N08825) INTRODUCTION ATI 825 alloy (UNS N08825) is an austenitic nickel-iron-chromium-molybdenum-copper alloy containing high levels of chromium, nickel, molybdenum and copper
FSection F. Sheets and Plates. Plates. Plates and Sheets. Plates. Plates. Sheets and Plates
FSection F HIGH STRENGTH LOW ALLOY STEELS HEAT TREATED CONSTRUCTIONAL ALLOY STEELS ABRASION RESISTING STEELS HIGH STRENGTH LOW ALLOY STEELS... 2-3 Sheets and Plates HEAT TREATED CONSTRUCTIONAL ALLOY STEELS...
Think Stainless, Think Encore STAINLESS STEEL FOR SPECIALTY APPLICATIONS. Specialty Metals to Support Innovative Manufacturing
STAINLESS STEEL FOR SPECIALTY APPLICATIONS Specialty Metals to Support Innovative Manufacturing Specialty Metals to Support Innovative Manufacturing Encore Metals is a specialist supplier of high grade
1. Scope :- 2. Referenced Documents :-
Standard Specification for Forged or Rolled N06030, N06022, N06035, N06200, N06059, N06686, N08020, N08024, N 08026, N08367, N10276, N10665, N10675, N 10629, N08031, N06045, N06025, and R20033 Alloy Pipe
STOCK LIST COQUITLAM, BC, CANADA SHEET PLATE COIL PIPE TUBE ROD BAR FITTINGS FLANGES EXTRUSIONS ALUMINUM BRASS BRONZE COPPER COPPER-NICKEL
STOCK LIST SHEET PLATE COIL PIPE TUBE ROD BAR FLANGES EXTRUSIONS ALUMINUM BRASS BRONZE COPPER COPPER-NICKEL STAINLESS STEEL COQUITLAM, BC, CANADA S T AINLESS STEEL ALLOYS 303, 304, 304L, 316, 316L, 317L,
Standard Specification for UNS N08020, UNS N08024, and UNS N08026 Nickel Alloy Bar and Wire 1
Designation: B 473 96 (Reapproved 2002) e Standard Specification for UNS N08020, UNS N08024, and UNS N08026 Nickel Alloy Bar and Wire This standard is issued under the fixed designation B 473; the number
ATI 15-7 ATI Technical Data Sheet. Semi-Austenitic Stainless Steel INTRODUCTION
ATI 1-7 Semi-Austenitic Stainless Steel (UNS S1700) INTRODUCTION ATI 1-7 Precipitation Hardening Alloy (S1700, AISI Type 632) is a chromium-nickel-molybdenum-aluminum semi-austenitic precipitation hardening
Standard Specification for Seamless and Welded Austenitic Stainless Steel Sanitary Tubing 1
Designation: A 270 01 An American National Standard Standard Specification for Seamless and Welded Austenitic Stainless Steel Sanitary Tubing 1 This standard is issued under the fixed designation A 270;
Stainless Steel 310/310S (UNS S31000/ UNS S31008)
Stainless Steel 310/310S (UNS S31000/ UNS S31008) Austenitic Stainless Steel 310/310S offers excellent resistance to oxidation up to 2000oF. It is a low grade steel that prevents embrittlement and sensitization.
Standard Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes 1
Designation: A 564/A 564M 04 Standard Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes 1 This standard is issued under the fixed designation A 564/A 564M; the
ATI 321 /ATI 347 /ATI 348
ATI 321 /ATI 347 /ATI 348 Stainless Steel: Austenitic (UNS S32100, S34700, S34800) GENERAL INFORMATION ATI 321 (UNS S32100), ATI 347 (UNS S34700), and ATI 348 (UNS S34800) alloys are stabilized stainless
Standard Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service
SA-268/SA-268M ASME BPVC.II.A-2015 Standard Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service 1. Scope 1.1 This specification covers a number of
High-Strength Low-Alloy Steels
High-Strength Low-Alloy Steels Introduction and Overview High-strength low-alloy (HSLA) steels, or microalloyed steels, are designed to provide better mechanical properties and/or greater resistance to
SPECIFICATION FOR PRESSURE VESSEL PLATES, CARBON STEEL, FOR MODERATE- AND LOWER-TEMPERATURE SERVICE
Technical Literature: ASME SA-516 [ASTM A516] Company Website: www.metalspiping.com SA-516/SA-516M Carbon & Low Alloy Steels From Hebei Metals Industrial Limited SPECIFICATION FOR PRESSURE VESSEL PLATES,
The ATI 17-4 precipitation hardening stainless steel (S17400) is covered by the following wrought product specifications.
ATI 17-4 Precipitation Hardening Stainless Steel (UNS S17400) INTRODUCTION ATI 17-4 precipitation hardening stainless steel (S17400), Type 630, is a chromium-nickel-copper precipitation hardening stainless
ATI 201 HP /ATI 201L HP
Stainless Steel: Austenitic (UNS S20100 and S20103) GENERAL PROPERTIES and L austenitic stainless steels belong to the 200 series of Cr-Mn-Ni stainless alloys, which are similar to the 300 series of Cr-Ni
Nickel Based Superalloy Hastelloy B-3 (UNS N10675)
Nickel Based Superalloy Hastelloy B-3 (UNS N10675) Hastelloy B-3 is manufactured for providing excellent resistance to reducing acids at the different content %s and temperature limits. It shows better
STULZ-SICKLES STEEL COMPANY
STULZ-SICKLES STEEL COMPANY SINCE 1916 Providing Years of Wear Resistant Service to the Railroad Industry Railroad ELIZABETH, NEW JERSEY COLTON, CALIFORNIA 800-351-1776 800-572-5809 www.stulzsicklessteel.com
Alloys SUPER SQUARE
Alloys ETD 150...8-2 ETD 150 Rounds...8-2 AISI 4140/41L40 - Annealed...8-3 AISI 4140 - Annealed Flats And Squares... 8-4 thru 8-5 AISI 4140 - Annealed Rounds... 8-5 thru 8-6 AISI 4140 Rounds HR Q&T...8-7
VDM Alloy 80 A Nicrofer 7520 Ti
VDM Alloy 80 A Nicrofer 7520 Ti Material Data Sheet No. 4048 February 2017 February 2017 VDM Alloy 80 A 2 VDM Alloy 80 A Nicrofer 7520 Ti VDM Alloy 80 A is a nickel-chromium alloy that can be age-hardened.
Government Recognized Export House OHSAS 18001:2007 ISO 14001:2004 PED Approved Company.
Government Recognized Export House OHSAS 18001:2007 ISO 14001:2004 PED Approved Company. Phone : +91 22 4343 1313 (25 Lines) Fax : +91 22 2389 4311 Email : sales@rolfalloy.com Designation: A 334/A 334M
Standard Specification for Seamless and Welded Austenitic and Ferritic/Austenitic Stainless Steel Sanitary Tubing 1
Designation: A 270 03 Standard Specification for Seamless and Welded Austenitic and Ferritic/Austenitic Stainless Steel Sanitary Tubing 1 This standard is issued under the fixed designation A 270; the
Designation: B
Designation: B 446 0 Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625), Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N0629), and Nickel-Chromium-Molybdenum-Tungsten Alloy
Incoloy Alloy 800H/800HT (UNS N08810/088011)
Incoloy 800H/800HT (UNS N08810/088011) Incoloy 800H/HT is an outstanding corrosion resistant alloy that is recommended for use in the high temperature industrial conditions. It has higher strength than
RELIABLE PIPES & TUBES LTD.
RELIABLE PIPES & TUBES LTD. OHSAS 18001:2007 CERTIFIED ISO 9001:2008 CERTIFIED ISO 14001:2004 CERTIFIED PED CERT NO 01 202 IND/Q-11-0033 GOVT. RECOGNIZED EXPORT HOUSE Manufacturer & Exporters of Monel,
409 Ni STAINLESS STEEL
409 Ni STAINLESS STEEL P R O D U C T D ATA B U L L E T I N Superior Corrosion Resistance to Mild and Low-Alloy Steels Cost Effective Alternative to Austenitic Stainless AK Steel 409 Ni Stainless Steel
RA17-4 stainless. Introduction
RA17-4 stainless Introduction RA17-4 is an age-hardening martensitic alloy combining high strength with the corrosion resistance of stainless steel. Hardening is achieved by a short-time, simple lowtemperature
Standard Specification for Carbon Steel Forgings for Piping Applications 1
Addr: 29, 227 Changle Rd., Shanghai, 2000. Tel: 86-2-6470807 Designation: A 0/A 0M 0 Endorsed by Manufacturers Standardization Society of the Valve and Fittings Industry Used in USDOE-NE Standards Standard
Standard Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip 1
Designation: A 69 06 Standard Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip 1 This standard is issued under the fixed designation A 69; the number
Standard Specification for Nickel-Iron-Chromium Alloy Plate, Sheet, and Strip 1
Designation: B 40 06 Standard Specification for Nickel-Iron-Chromium Alloy Plate, Sheet, and Strip This standard is issued under the fixed designation B 40; the number immediately following the designation
ASTM A105/A105M-10. Standard Specification for Carbon Steel Forgings for. Piping Applications ¹
Standard Specification for Carbon Steel Forgings for Piping Applications ¹ 1. Scope :- 1.1 This specification covers forged carbon steel piping components for ambient and higher temperature service in
Grades : SS 304, 304L, 304H, 316, 316L, 316LN, 316Ti, 309, 310S, 317L, 321, 347,
Unifit MetalloysInc (UMI) is one of the leading Manufacturer, Exporter and Supplier of High Quality Stainless Steel Pipes & Tubes, Flanges, Pipe Fittings, Round Bars, Sheets and Plates Etc.Stainless steel
409 Ni STAINLESS STEEL
409 Ni STAINLESS STEEL Bus Frames Dryer Component Intermodal Containers Rail Cars Trailers AK STEEL 409 Ni is an ideal material for applications requiring weldability and toughness superior to standard
Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes 1
Designation: A 213/A 213M 99a e1 An American National Standard Used in USDOE-NE standards Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger
ATI 13-8 ATI Technical Data Sheet. Precipitation Hardening Alloy INTRODUCTION FORMS AND CONDITIONS. (UNS S13800, ASTM Type XM-13)
ATI 13-8 Precipitation Hardening Alloy (UNS S13800, ASTM Type XM-13) INTRODUCTION ATI 13-8 alloy (UNS S13800) is a martensitic precipitation-hardening stainless steel that has excellent strength, high
Subway Cars. Applications Potential
301 STAINLESS STEEL P R O D U C T D ATA B U L L E T I N Aircraft Structural Parts Roof Drainage Cooking Utensils Automotive Trim Subway Cars Applications Potential Type 301 is an austenitic chromium-nickel
Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service 1
Designation: A 269 04 Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service 1 This standard is issued under the fixed designation A 269; the number immediately
Item 442 Metal for Structures
Item 442 Metal for Structures 1. DESCRIPTION 2. MATERIALS Provide structural steel, high-strength bolts, forgings, steel castings, iron castings, wrought iron, steel pipe and tubing, aluminum castings
AEROSPACE MATERIAL SPECIFICATION
AEROSPACE MATERIAL SPECIFICATION AMS 5659L Issued SEP 1965 Revised JAN 2004 Superseding AMS 5659K Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 15Cr - 4.5Ni - 0.30CB (Nb) - 3.5Cu
Standard Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service 1
Designation: A 268/A 268M 0 An American National Standard Standard Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service This standard is issued under
Standard Specification for Structural Steel for Ships 1
Designation: Standard Specification for Structural Steel for Ships 1 This standard is issued under the fixed designation A 131/A 131M; the number immediately following the designation indicates the year
AEROSPACE MATERIAL SPECIFICATION
AEROSPACE MATERIAL SPECIFICATION Licensed to Juan Rodriguez AMS 5754M Issued MAY 1954 Revised AUG 2007 Superseding AMS 5754L Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 47.5Ni
DATA SHEET ZERON 100 UNS S32760 THE GLOBAL LEADER IN SPECIALTY ALLOYS ALLOYS AND PROCESSING
DATA SHEET ZERON 100 UNS S32760 THE GLOBAL LEADER IN SPECIALTY ALLOYS ALLOYS AND PROCESSING ZERON 100 Data Sheet Contents Specifications, Chemical Composition, Applications and Features...2 Performance
Standard Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip 1
Designation: A69 06 Standard Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip 1 This standard is issued under the fixed designation A69; the number immediately
Applications Potential
P R O D U C T D A T A B U L L E T I N STAINLESS 301STEEL UNS S30100 High Strength and Good Ductility When Cold Worked Excellent Corrosion Resistance Readily Welded Readily Formed and Drawn Economical Oxidation
DATA SHEET ZERON 100 UNS S32760 THE GLOBAL LEADER IN SPECIALTY ALLOYS
DATA SHEET ZERON 100 UNS S32760 THE GLOBAL LEADER IN SPECIALTY ALLOYS corrosion resistant alloys ZERON 100 Data Sheet Contents Specifications, Chemical Composition, Applications and Features...2 Performance
301 STAINLESS STEEL. Aircraft Structural Parts. Automotive Trim. Cooking Utensils. Roof Drainage. Subway Cars
301 STAINLESS STEEL Aircraft Structural Parts Automotive Trim Cooking Utensils Roof Drainage Subway Cars TYPE 301 is an austenitic, chromium-nickel stainless steel. This alloy is non-magnetic in the annealed
SPECIFICATION FOR PRESSURE VESSEL PLATES, ALLOY STEEL, QUENCHED AND TEMPERED 8 AND 9% NICKEL
Technical Literature: ASTM A553 [ASME SA-553] Company Website: www.metalspiping.com You Reliable Supplier of Ferrous & Non-Ferrous Piping Materials SPECIFICATION FOR PRESSURE VESSEL PLATES, ALLOY STEEL,
Nickel Based Superalloy Incoloy 800 (UNS N08800)
Nickel Based Superalloy Incoloy 800 (UNS N08800) Nickel-Iron-Chromium alloy Incoloy 800 has fine strength and suitable resistance to oxidation and carburization at high temperatures. It offers elevated
201 STAINLESS STEEL. Appliances. Architectural Applications. Automotive Trim. Cooking Utensils
201 STAINLESS STEEL Appliances Architectural Applications Automotive Trim Cooking Utensils TYPE 201 is an austenitic, chromium-nickel-manganese stainless steel that was developed originally to conserve
Standard Specification for Precipitation-Hardening Nickel Alloy Bars, Forgings, and Forging Stock for High-Temperature Service 1
Designation: B 67 98 AMERICAN SOCIETY FOR TESTING AND MATERIALS 00 Barr Harbor Dr., West Conshohocken, PA 9428 Reprinted from the Annual Book of ASTM Standards. Copyright ASTM Standard Specification for
ATI 601 ATI 601. Technical Data Sheet. Nickel-base Alloy INTRODUCTION PRODUCT FORMS SPECIFICATIONS & CERTIFICATES (UNS N06601)
Nickel-base Alloy (UNS N06601) INTRODUCTION alloy (UNS Designation N06601) is an austenitic nickel-chromium-iron alloy designed for both heat and corrosion resistance. As compared to ATI 600 alloy (UNS
ATI ATI 2205 Alloy (UNS S31803 and S32205) Duplex Stainless Steel. Technical Data Sheet
Alloy (UNS S31803 and S32205) Duplex Stainless Steel GENERAL PROPERTIES alloy (UNS S31803 and/or S32205) is a nitrogenenhanced duplex stainless steel alloy. The nitrogen serves to significantly improve
ASTM A335 Chrome Moly Pipe. Welcome to Sunny Steel Enterprise Ltd. By Mr. Sum Xu
ASTM A335 Chrome Moly Pipe By Mr. Sum Xu ASTM A335 Pipe (ASME S/A335, Chrome-Moly) is a seamless ferritic Alloy-Steel Pipe for high temperature service. Welcome to Sunny Steel Enterprise Ltd. Sunny Steel
15-5 PH STAINLESS STEEL
Aerospace Chemical Food Processing Metalworking Paper Industries AK STEEL offers a combination of high strength and hardness, good corrosion resistance plus excellent transverse mechanical properties.
ATI 332 ATI 332. Technical Data Sheet. Stainless Steel: Austenitic GENERAL PROPERTIES TYPICAL ANALYSIS PHYSICAL PROPERTIES
ATI 332 Stainless Steel: Austenitic (UNS N08800) GENERAL PROPERTIES ATI 332 alloy is a nickel and chromium austenitic stainless steel designed to resist oxidation and carburization at elevated temperatures.
Standard Specification for Nickel Rod and Bar 1
Designation: B 60 05 Standard Specification for Nickel Rod and Bar This standard is issued under the fixed designation B 60; the number immediately following the designation indicates the year of original
J.I.C. HYDRAULIC TUBING Seamless & Welded Hydraulic Fluid Line 23 Seamless Burst Pressures & Working Pressures 24 Welded Burst Pressures 25
TABLE OF CONTENTS STEEL & ALLOY ROUND MECHANICAL TUBING Drawn Over Mandrel (DOM) 3-15 Cold Drawn Seamless (CDS) 3-15 Hot Rolled Seamless (HRS) 3-15 Electric Resistance Welded (ERW) 3-15 Seamless 4130/4140
SECTION 9 Aluminum. SECTION 9: Aluminum General Information Diamond Floor Plate
Plate & Sheet Expanded Metal & Grating Structurals & Bar Shapes HR Bars & Reinforcing SECTION 9 Aluminum SECTION 9: Aluminum... 131 General Information... 132-134 Sheets... 135-137 Diamond Floor Plate...
Custom 455, UNS S45500
Custom 455, UNS S45500 Shaped, Flat, Square, Round, Fine Wire, Plated and Un-plated Specifications: AMS 5617, AMS 5860, ASTM A313 ASTM A564, ASTM A693 Custom 455 Alloy Description Custom 455 stainless
Stainless Sheet 201, 301, 304, 304L, 309, 7 gauge - 28 gauge 316, 316L, 321, 409, 410, (.1793 to.0149 ) up to 72 wide 410S, 430, 439
Providing a World of Metals to Canada Diversified is a stainless steel and aluminum service center providing sheet, plate, bar, strip, tubing and structural angle to the Canadian market since 1971. After
Hastelloy G-30 (UNS N06030) Chemical Composition
Hastelloy G-30 (UNS N06030) Hastelloy G-30 is commonly used for providing excellent resistance to chemical conditions. It offers resistance to nitric acid, phosphoric acid, hydrochloric acid and hydrofluoric
Specification Product Form ASTM ASME AMS Federal or Military Plate, Sheet and Strip B 127 SB QQ-N-281 B 163 B165 B164 B564
ATI 400 Nickel-Base Alloy (UNS N04400) INTRODUCTION ATI 400 alloy (UNS N04400) is a ductile nickel-copper alloy with resistance to a variety of corrosive conditions. The alloy is most frequently applied
41003 STAINLESS STEEL
41003 STAINLESS STEEL D ATA S H E E T Formable and Weldable in Heavy Sections Refined Grain Structure Leads to Good Toughness Ferritic as Annealed Low Cost AK Steel 41003 is an economical ferritic stainless
Standard Specification for Carbon and Alloy Steel Forgings for Thin-Walled Pressure Vessels 1
Designation: A 372/A 372M 03 An American National Standard Standard Specification for Carbon and Alloy Steel Forgings for Thin-Walled Pressure Vessels 1 This standard is issued under the fixed designation
316/316L STAINLESS STEEL
316/316L STAINLESS STEEL P R O D U C T D ATA B U L L E T I N Valve and Pump Trim Digesters Chemical Equipment Evaporators Pharmaceutical and Photographic Equipment Applications Potential Type 316 Stainless
WWR For Structural Applications A Discussion of Current Product Knowledge and Practices
TF 208-R-08 WWR For Structural Applications A Discussion of Current Product Knowledge and Practices INTRODUCTION With its greater strength, generally higher ductility, and significantly lower placing and
ITEM 442 METALS FOR STRUCTURES
AFTER NOVEMBER 1, 2008 ITEM 442 METALS FOR STRUCTURES 442.1 Description. These specifications shall govern for materials such as structural steel, wrought iron, bronze, and other metals used in structures,
NORRIS. Drive Rods. Engineered performance. Designed tough.
NORRIS Drive Rods Engineered performance. Designed tough. 1 (25,4 mm) Norris Drive Rods with 7/8 (22,23 mm) fullsize couplings Tubing size Improvement 27/8 (73,0 mm) 37% improvement in flow area when compared
AMERICAN NATIONAL STANDARD ANSI/NAAMM STANDARD. Maximum Bearing Bar Depth / 2 (63.5 mm)
METAL BAR GRATING AMERICAN NATIONAL STANDARD ANSI/NAAMM STANDARD MBG 531-17 GRATINGS 5 ANSI/NAAMM MBG 531-17 SEPTEMBER 7, 2017 METAL BAR GRATING MANUAL EIGHTH EDITION Maximum Bearing Bar Depth... 2 1 /
Nominal Composition. Weight %
HASTELLOY HYBRID-BC1 Principal Features High Resistance to Hydrochloric Acid, Sulfuric Acid, Pitting, and Crevice Corrosion HASTELLOY HYBRID-BC1 (UNS N10362) alloy possesses much higher resistance to hydrochloric
ASTM A420-Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service
ASTM A420-Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service 1. Scope 1.1 This specification 2 covers wrought carbon steel and alloy steel fittings
Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing for General Service 1
Designation: A 789/A 789M 08b Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing for General Service 1 This standard is issued under the fixed designation A 789/A
NITRONIC 19D LEAN DUPLEX STAINLESS STEEL. Excellent Stress Corrosion Cracking Resistance. Improved Welding Characteristics
NITRONIC 19D LEAN DUPLEX STAINLESS STEEL P R O D U C T D ATA B U L L E T I N Excellent Stress Corrosion Cracking Resistance High Strength Improved Welding Characteristics Resists Sigma Phase Formation
CHROMESHIELD 22 STAINLESS STEEL
CHROMESHIELD 22 STAINLESS STEEL P R O D U C T D ATA B U L L E T I N Appliances Food Service Equipment Architectural Welded Components Tubing Cookware Applications Potential CHROMESHIELD 22 Stainless Steel
SECTION MISCELLANEOUS METALS
PART 1 GENERAL 1.1 WORK OF THIS SECTION A. Contractor shall provide all labor, materials, equipment and incidentals as shown, specified and required to furnish and install all miscellaneous metal fabrications
SPECIFICATION FOR NICKEL ALLOY FORGINGS
SPECIFICATION FOR NICKEL ALLOY FORGINGS 01 (Identical with ASTM Specification B 564-00 except that certification has been made mandatory.) 1. Scope 1.1 This specification covers forgings of nickel alloy
Mission Statement. State Steel strives to provide quality products and services at competitive
Mission Statement State Steel strives to provide quality products and services at competitive prices. This commitment is demonstrated with several branch locations all offering large, diverse inventories
Standard Specification for Heat-Resisting Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels 1
Designation: A 240/A 240M 00 Standard Specification for Heat-Resisting Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels 1 This standard is issued under the fixed
MATERIAL PROPERTIES. Spring Characteristics
MATERIAL PROPERTIES The highest grades of spring-wire materials are used in fabricating our springs. To create cost-effective warehousing of our stock spring inventory for our customers, we can only offer
304/304L STAINLESS STEEL
304/304L STAINLESS STEEL P R O D U C T D ATA B U L L E T I N Architectural Moldings and Trim Textile Kitchen Equipment Paper Pharmaceutical and Chemical Industry Processing Equipment Applications Potential
Material Selection Jacob Klinginsmith, Russ Glass Naomi Sanders, Becky Moffitt
Material Selection Jacob Klinginsmith, Russ Glass Naomi Sanders, Becky Moffitt The most significant feature of our poster is the slider bar graph at the top of each material category. This quick reference
Standard Specification for Welded Stainless Steel Mechanical Tubing 1
Designation: A 554 98 e An American National Standard Standard Specification for Welded Stainless Steel Mechanical Tubing This standard is issued under the fixed designation A 554; the number immediately
316/316L STAINLESS STEEL
316/316L STAINLESS STEEL Chemical Processing Equipment Exhaust Manifold Furnace Pans Marine Exposed Tubing TYPE 316 is widely used in applications requiring corrosion resistance superior to Type 304, or
Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing for General Service 1
Designation: A789/A789M 17 Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing for General Service 1 This standard is issued under the fixed designation A789/A789M;