SECTION PIER 94 HIGH MAST LIGHTING. A. Replace existing high mast lighting poles M and N located at Pier 94.
|
|
- Gladys Anthony
- 6 years ago
- Views:
Transcription
1 SECTION PIER 94 HIGH MAST LIGHTING PART 1 - GENERAL 1.01 SCOPE A. Replace existing high mast lighting poles M and N located at Pier 94. B. Provide templates of existing pole foundation M and N to ensure new pole base plate will match existing pole foundation, bolt size and pattern. C. Remove and dispose of existing high mast lighting poles and maintain existing pole foundations and electrical raceway and wiring. D. Provide new high mast system complete with new pole to mount on existing pole foundation, motorized lowering ring and LED type fixtures. E. New high mast systems shall interface with existing modified lighting controlled circuits shown on drawings. F. All high mast components shall be new and warranted EXISTING CONDITIONS A. High mast lighting pole foundations are approximately 8 high. B. Lighting controlled circuits consist of three circuits at each pole (2 full lighting circuits and 1 security lighting circuits). Only two circuits at each pole shall be used (1 for full lighting and winch system and 1 for security). C. Circuits are 480V, 3-phase, 3-wire system SUMMARY A. New high mast system will consist of removal and disposal of existing high mast lighting poles, new structural high mast design to mount on existing pole foundation, new mechanical/electrical lowering system design and new lighting design DESCRIPTION A. High mast system shall include but not limited to the following: high mast poles including head frame and lowering ring. 2. Internal winch assembly. 3. Internal circuit wiring (minimum) high mast LED lighting fixtures per pole for normal and security lighting. B. Provide new high mast system consisting of new structural high mast design to mount on existing pole foundation. Obtain templates of existing pole foundation and submit to pole manufacture to ensure base plate will match existing pole foundation, bolt size and pattern
2 C. Provide new lighting design with an average of 5 fc (foot-candle) for full lighting and average of 1 fc for security REQUIRED SUBMITTALS A. Provide design and shop drawings for the following: high mast assemblies, including head frame, lowering ring and internal hoisting assembly. 2. Internal winch assembly. 3. High mast lighting fixtures. 4. Lighting study for full lighting and security lighting for areas as indicated by the PORT of San Francisco. 5. Electrical design. 6. Structural design. B. Additional Submittals: PART 2 - PRODUCTS 1. Structural drawings and calculations shall be completed by a California licensed engineer, and submitted for review by the Port of San Francisco Project Manager. Approval is a prerequisite to fabrication. 2. Worker Qualifications: See paragraph 3.02, A herein HIGH MAST POLES A. Poles shall be Valmont Industries, Inc. Catalog No. HM080-SPCL-LD25, or approved equal. B. Poles shall be 80 feet high and shall include shaft, handhole, support plate, anchor base and nuts. The pole complete with lowering device and luminaries in place shall be capable of withstanding a sustained wind velocity of not less than 80 MPH with gusts up to 130% at three seconds. Poles shall be fabricated from high strength low alloy steel conforming to ASTM A588. C. Tapered tube type to be used for pole sections shall meet tensile strength requirements of ASTM A595, Grade B or ASTM A572 Grade 65. D. Sectional poles shall consist of round and multi-tapered steel tubes with a standard taper of 0.14 inches per foot. Sectional pole sections shall telescope such that the upper section slip-fits the section below by a minimum of 2 inches less than 1.5 times the upper section inside diameter. E. Shaft shall be prime-painted in accordance with painting specification contained herein. Steel used in fabricating the shaft shall have minimum yield strength of 65,000 psi following fabrication. Pole sections shall be fabricated from material per ASTM a-572, Fr. A. F. Shaft shall have a 10 by 30 minimum reinforced handhole to allow adequate clearance for installing, maintaining and servicing the internal lowering device. Handhole reinforcement with a minimum of 1 thick reinforcing bar frame. The bar frame shall be sized such that it will not interfere with the operation of the lowering device. The handhole opening shall begin approximately 15 up from the base of the pole. Opposite the handhole shall be a support plate for mounting of the winch assembly and circuit breakers. A handhole cover shall be provided with a gasketed, padlockable cover
3 G. The anchor base shall be integrally welded base plate designed to meet or exceed the strength of the adjacent pole shaft section. The base plate connection shall be full penetration butt weld with a backup bar. H. Each base plate of each high mast pole shall be field verified to accommodate existing bolt pattern type, anchor bolt circle diameter, bolt projection, and shall be drilled to match the existing bolt circle. Each of the existing bolt circles shall field verified. I. Testing and inspection of welds: The contractor or manufacturer shall employ and pay all costs of an approved testing laboratory to make in-shop ultrasonic tests for base plate welds of all steel poles for compliance with design criteria. Any defective weld shall be chipped out, re-welded and retested. Certification of welds shall be furnished by the testing laboratory and results submitted to the PORT of San Francisco Engineer on record. Welds shall be refinished to the same quality as the pole finish to protect from the elements. When certification of welds has been approved, installation of high mast light systems may begin. J. Pole to be galvanized coating inside and out per ASTM A LOWERING SYSTEM DEVICES A. The lowering system shall be Holophane Catalog No. LD25, or approved equal. B. Lowering system shall consist of head frame, luminaire/lowering ring and winch assembly including motor. C. The head frame structure shall be zinc coated steel and attached to the pole securely with stainless steel hardware. The head frame shall include a minimum of two nominal diameter steel hoisting cable sheaves for each lowering cable. Cable sheaves shall be spaced so all vertical cable paths are parallel to each other. Cable sheaves shall be made of hot rolled steel and be manufactured by splitting and spin-forming the sheave blank. The cross-section of the spin formed sheave groove shall have a radius to greater than half the nominal cable diameter. The sheave shall be corrosion resistant. Oil impregnated sintered bronze bushings shall be pressed into the steel sheave hub and shall ride on 304 stainless steel shafts. D. A minimum of three stainless steel hoisting cables rated for lifting two times the entire assembly alone. E. The power cord roller assembly shall consist of rollers mounted between two cold-rolled steel plates to ensure power cord does not fall off roller track with a keeper bar on each end to keep the power cord on track during pole erection and during normal operation. The rollers with steel plates shall be spaced to allow the power cord to ride smoothly. Plates shall be corrosion resistant. Rollers to be mounted on AISI 304 stainless steel shafts. A minimum of four rollers shall be provided to allow minimal bending radius of the power cord, and also be spaced so that vertical power cord paths are parallel. F. The head frame shall be provided with a corrosion resistant metallic cover to enclose all internals for protection from the outdoor elements and is attached with stainless steel hardware. G. The head frame shall include guides for each cable assembly of the lowering ring for latching into place when lowering ring is raised. A locking mechanism shall be provided to lock lowering ring into place when raised with means of unlocking for service and maintenance from the ground when being lowered. H. The latching and locking of each latching mechanism shall be signaled to an indicator that will be
4 visible from the ground. The latching mechanism shall not be impaired by formation of ice and shall not require adjustment after the original installation. I. The luminaire ring shall be fabricated to support 12 high-mast fixtures and designed to protect both the pole and shaft while lowered or raised. Luminaire ring shall be stainless steel or galvanized steel. J. Power cable shall be provided with suitable number of conductors rated for the voltage and current carrying capacity for the total load with a maximum voltage drop of 3% and EPR insulation suitable for at least 105 degree C. K. All terminations shall be weather tight wiring chamber through weather tight cable connections. L. Luminaire ring shall be provided with rollers for the centering arm with water-resistant, non-marking material. Spring loaded centering arm design shall be provided for tapered high mast poles which will center the luminaire ring while ascending and descending along the pole. The arm system shall be capable of keeping the ring concentric with the pole in winds up to 30 MPM. All hardware shall be stainless steel. M. Ultimate support of the 12 luminaire ring shall not be sacrificed by individual or total spring failure WINCH SYSTEM A. Assembly: 1. Winch and motor assembly shall be internally located in the pole. 2. Winch motor shall be rated for existing electrical service. Transformer shall be provided as necessary. The transformer shall be properly sized and rated to power a winch motor, and shall be located in the base of the pole and be accessible through the handhole. 3. Motor shall be controlled by a polarity reversing switch connected to a 20 remote cord. 4. The winch shall have an ultimate strength of five times the lifted load with which it will be used. The winch shall include an integral drag brake on the worm shaft to prevent free spooling of the winch. The winch shall be designed for at least intermittent power operation, but also have hand cranked capability. 5. The winch shall be rewound with stainless steel cord of sufficient length to maintain at least four (4) complete wraps on the drum after the device has been lowered to its lowest position. The drum shall be supported at both ends and keepers shall be provided to ensure that uncoiled cable will rewrap onto the drum CIRCUIT BREAKERS AND CABLING SYSTEM A. Feeder circuits shall terminate at 3 phase circuit breakers in a NEMA 3R enclosure installed within the base of the pole so that the circuit breakers are operable through the handhole and interface with existing lighting controls for full lighting, security lighting and winch power. B. Circuit run shall be continued to the luminaire ring by means of a heavy duty cable. A weather tight twist-lock connector for each circuit shall be installed at the lower end of the cable to disconnect cable and permit lowering of luminaire ring for servicing. A water tight cap shall be provided for twist-lock connecter when each cabling systems are not in use
5 C. Furnish for installation three separate cabling systems: 1. Normal lighting. 2. Security lighting. 3. Winch system D. The cabling system shall be of type suitable for this specific application and shall comply with applicable codes LUMINAIRES A. Luminaires shall be Holophane catalog No.HMLED2 12 4K AH G AW FD2 P7 PSC High Mast Gen 11 luminaire, utilizing 12 LED COB modules enclosed with borosilicate glass refractor, opened fixture, IP 66 rated LED modules UL, listed 1598, with symmetric IES Type V distribution or approved equal. B. Luminaires shall be provided with standard NEMA 7 pin receptacle with shorting cap for future connections for wireless and dimming controls. C. Available voltage at existing poles is 480V, 3-phase, 3-wire. D. The luminaires shall be provided with 100,000 hour, 61,410 lumen, 12 chip-on-board (COB) LED Wide Type, UL Listed 40C E. The maximum weight of the luminaires shall not exceed 70 pounds. F. The housing shall be die cast aluminum and shall provide a weather tight environment for all components and shall pass the UL listed to operate in 40 degree C ambient. The cast aluminum bracket arm clamp shall allow for +/- 3 degree adjustment for leveling the luminaire. All components shall be of non-corrosive material or have positive corrosion protection and the complete fixture shall be 3G vibration tested. Provide pre-treatment and painting process yields a finish that achieves a scribe creep age rating of 8 (ASTM D1654) after over 5,000 hours exposure to salt fog chamber (ASTM B117). G. Luminaire shall have Class I rated LED drivers rated for 100,000 hours life at 25C, L80 at 100,000. Luminaire s surge protection shall meet ANSI/IEEEC62.41 category C high for AS voltage, C low for AH voltage. The luminaire must function normally and show no evidence of failure upon completion of the test. H. All driver components shall be factory tested and pre-wired to the quick disconnect. I. Luminaire s optical assembly shall be symmetric distribution. J. Fixture shall be provided with dark sky cutoff. PART 3 - INSTALLATION 3.01 REQUIREMENTS A. All electrical installations shall confirm to the codes and standards outlined in this Section. In general, and unless otherwise indicated on drawings, follow equipment manufactures written instructions for
6 installation of electrical equipment WORKMANSHIP A. Qualifications: All electrical work shall be performed by electricians who have completed an apprenticeship training program for electricians approved by the California Division of Apprenticeship Standards, each of whom shall have a minimum of five (5) years of journeyman level experience performing similar electrical work in similar facilities. Workers performing electrical work on medium voltage switchgear shall have a minimum of five years experience working with medium voltage. The Contractor shall require the workers hired to perform electrical work on this Contract to submit documentation proving that these training and experience requirements are met. Prior to engaging the workers on the electrical work, the contractor shall submit an AFFIDAVIT to the Port identifying the workers and stating that each of the electrical workers meet these minimum requirements. B. Ensure that all equipment and materials fit properly in their installations. C. Perform any required work to correct improperly fit installations at no additional expense to the City INSTALLATION OF POLES, HIGH MAST LUMINARES, AND LOWERING DEVICES A. Optical assemblies shall be inspected and cleaned prior to hoisting to final operating position. B. Poles shall be assembled and cleaned prior to erection on foundation. Any damage to the finish caused during erection shall be repaired and restored to its specified condition. C. Contractor to provide or clean weep holes under the base of the pole to prevent accumulation of moisture. D. Pole leveling nuts shall be adjusted to make the poles true and vertical, after which any space between the base and the existing concrete footing shall be packed with grout. E. Luminaire assemblies shall be checked for loose nuts, bolts, rivets, screws, equipment finish, position of reflector, ballast and electrical connections before raising to top of pole. F. Contractor shall have a manufacturer s representative on site to inspect assembly and setting of all high mast lights. Manufacturer s representative shall submit a written report confirming all high mast lights are installed per the manufacturer s recommendations TESTING OF HIGH MAST LUMINARES & LOWERING DEVICES A. Contractor shall test all systems of high mast luminaires to ensure they are working properly after electrical connection is made. Each high mast shall be tested individually. Contractor shall demonstrate that the high mast lights are operational at the request of the Engineer. B. Contractor shall also test lowering device for proper operation. Contractor shall also demonstrate that the lowering devices are operation at the request of the Engineer. END OF SECTION
HIGH MAST CAMERA POLE ASSEMBLY GENERAL
10-3.24 HIGH MAST CAMERA POLE ASSEMBLY GENERAL The Contractor must furnish and install the following equipment for high mast camera pole assembly as described herein and as shown on the plans: 1. Camera
More informationSECTION CHAIN-LINK FENCES AND GATES 02821/1
SECTION 02821 - CHAIN-LINK FENCES AND GATES 02821/1 PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Chain-Link Fences: 2. Gates: horizontal slide or swing. 3. Fences installed where
More informationITEM 686 TRAFFIC SIGNAL POLE ASSEMBLIES (STEEL)
ITEM 686 TRAFFIC SIGNAL POLE ASSEMBLIES (STEEL) 686.1. Description. This Item shall govern for designing, fabricating, furnishing and erecting steel traffic signal pole assemblies of the various types
More informationA. Product Data shall be provided for each type of product indicated.
32 31 13 CHAIN LINK FENCES AND GATES SECTION 1 GENERAL 1.1 SUMMARY This Section includes the following: 1. Chain Link Fences 2. Gates for Chain Link Fences. See electrical specifications for electrical
More informationSECTION CRL50 AND CRL51 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS
SECTION 08 32 20 CRL50 AND CRL51 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS Page 1 of 6 USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,
More informationThis guide can be used to prepare a specification for incorporating free standing jib cranes into a competitively bid construction project.
SECTION 14651 FREE STANDING JIB CRANE ***** Gorbel, Inc. manufacturers a broad range of material handling cranes including monorail, bridge, gantry, and jib cranes. Numerous work station and industrial
More informationSECTION GROUNDING AND BONDING
SECTION 16060 PART 1 GENERAL 1.01 DESCRIPTION A. Section includes requirements for an electrical grounding system, including electrodes, grounding rods, connectors, insulators, equipment grounding and
More informationThis guide can be used to prepare a specification for incorporating free standing jib cranes into a competitively bid construction project.
GORBEL PRODUCT SPECIFICATIONS 2010 Gorbel, Inc., P.O., Box 593, Fisher, New York 14453-0593 PHONE: 800-821-0086, FAX: 585-924-6273; WEBSITE: www.gorbel.com November SECTION 41 22 31PRIVATE FREE STANDING
More informationBUSWAY LOW VOLTAGE (POW-R-WAY III) SECTION SECTION 16466
BUSWAY LOW VOLTAGE (POW-R-WAY III) PART 1 GENERAL 1.01 1.02 SCOPE The Contractor shall furnish and install the busway system including all necessary fittings, hangers and accessories as specified herein
More informationSECTION SECTIONAL OVERHEAD DOORS
SECTION 08360 SECTIONAL OVERHEAD DOORS PART 1 GENERAL 1.1 SECTION INCLUDES A. Aluminum Doors B. Track and Framing 1.2 RELATED SECTIONS A. Section 04810 - Unit Masonry Assemblies: Prepared opening in masonry.
More informationSECTION (Master Template Final-05) ELECTRICAL BOXES. A. Provide boxes for electrical equipment and wiring devices as follows:
SECTION 16130 (Master Template Final-05) ELECTRICAL BOXES PART 1 GENERAL 1.01 SECTION INCLUDES A. Provide boxes for electrical equipment and wiring devices as follows: 1. Wall and ceiling outlet boxes.
More informationDIVISION 1100 TRAFFIC
SECTION 1102 STREET LIGHTING GENERAL INFORMATION The Idaho State Electrical Board has determined that all street lights are to be provided with an external fuse disconnect, in a junction box between the
More information1. Vertical reciprocating conveyor, Hydraulic straddle VRC.
PART 1: GENERAL 1.01 Section Includes: 1. Vertical reciprocating conveyor, Hydraulic straddle VRC. a. Machine, controller, platform, structural steel hoist frame. b. Wire mesh enclosure and gates. Related
More informationSECTION HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMS
SECTION 26 05 29 HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMS PART 1 GENERAL 1.1 DESCRIPTION A. Scope: 1. CONTRACTOR shall provide all labor, materials, equipment, and incidentals as shown, specified, and
More informationFOUR FOLD DOORS-WITH SINGLE OVERHEAD MTD OPERATOR
FOUR FOLD DOORS-WITH SINGLE OVERHEAD MTD OPERATOR Section 083713- Four Fold Doors- With Single Overhead Mounted Operator Part 1-General 1.1 Related Document: A. Drawing and general provisions of contract,
More informationSECTION 1043 FENCE MATERIAL
SECTION 1043 FENCE MATERIAL 1043.1 Scope. This specification covers the material required in the construction of chainlink fence and woven wire fence. 1043.2 Basis of Acceptance. The basis of acceptance
More informationA-Series Aluminum Gantry Crane
SPANCO PRODUCT SPECIFICATIONS 1 A-Series Aluminum Gantry Crane This guide can be used to prepare a bid specification for the incorporation of an A-Series Gantry Crane into a competitive bid project or
More informationSECTION PRE-ENGINEERED MEMBRANE STRUCTURE
SECTION 13125 PART 1 - GENERAL 1.1 SUMMARY A. Section includes the design, engineering, fabrication and erection of a frame-supported, tensilemembrane structure complete with entrance and exit doors and
More informationITEM L-119 AIRPORT OBSTRUCTION LIGHTS DESCRIPTION
SECTION 74 AIRPORT OBSTRUCTION LIGHTS (FAA L-119) 74-1 GENERAL The Contractor shall perform all work required by the plans and specifications for construction of obstruction lights in accordance with the
More informationB. Polyethylene samples shall be submitted for Owner approval of color and quality.
Glass Rail ENGINEERED DASHERBOARD SPECIFICATIONS PART 1 - GENERAL 1.01 PROJECT SCOPE A. Contractor shall furnish and install one complete set of steel framed dasherboards as indicated on the drawings and
More informationHouston Community College 3200 Main Parking Garage November 15, 2010 Houston Community College
SECTION 323113 - CHAIN LINK FENCES AND GATES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSUGGESTED SPECIFICATIONS Pump Frames through 64132
TYPE HBB - HORIZONTAL SOLIDS-HANDLING WASTEWATER PUMPS Pump Frames 44081 through 64132 GENERAL Furnish and install Horizontal Flexible Coupled Dry Pit Pumping Units complete with all accessories and appurtenances
More information1. Cast-in-place concrete is specified in Section
SECTION 03 38 00 PART 1 - GENERAL 1.01 DESCRIPTION A. This Section describes the requirements for furnishing and installing post-tensioned slabs, jacks, jacking and anchors at Parking Structure, and record
More informationSECTION MECHANICAL SPECIFICATION GRIT COLLECTION EQUIPMENT
SECTION 11322 MECHANICAL SPECIFICATION GRIT COLLECTION EQUIPMENT PART 1 GENERAL 1.01 SCOPE There shall be furnished ( ) Grit Separator Mechanism(s) suitable for installation in (a) concrete tank(s) -ft.
More informationUNDERGROUND SERVICES SECONDARY
Reference UNDERGROUND SERVICES SECONDARY Underground services secondary... U- 1 General requirements for underground service... U- 2 Name of parts for underground service... U- 3 Conduit layouts... U-
More informationSPORTS AND STADIUM LIGHTING. Solutions for Amatuer and Professional Athletic Venues
SPORTS AND STADIUM LIGHTING Solutions for Amatuer and Professional Athletic Venues ENGINEERED SUPPORT STRUCTURES Now a global network of 50 facilities spanning 15 countries, Valmont Industries consists
More informationSECTION CHAIN LINK FENCES AND GATES (GALVANIZED) A. Fence framework, fabric, gates, and accessories.
SECTION 02830 CHAIN LINK FENCES AND GATES (GALVANIZED) 1.0 GENERAL 1.1 Section Includes A. Fence framework, fabric, gates, and accessories. B. Excavation for post bases; concrete footing for posts. C.
More informationAmerican Metal Specialties, Inc.
American Metal Specialties, Inc. www.cablerailings.com (253) 272-9344 (253) 627-3843 Fax PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 05 73 00 STAINLESS STEEL ORNAMENTAL HANDRAILS AND RAILINGS For best
More informationAluminum Component Pipe Railings
1 SECTION 05 7360 ALUMINUM COMPONENT PIPE RAILINGS PART 1 GENERAL 1.01 SECTION INCLUDES A. Aluminum component pipe handrails and railings. 1.02 RELATED REQUIREMENTS A. Section 02 9000: Landscaping: Installation
More informationANSI/ ASME HST Performance Standard For Overhead Electric Wire Rope Hoists
SECTION 412213- BRIDGE CRANES Part 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationEVALUATION REPORT. PFC-5551 Reissued April 1, Filing Category: DESIGN Steel (038)
ICBO Evaluation Service, Inc. 5360 WORKMAN MILL ROAD WHITTIER, CALIFORNIA 90601-2299 A subsidiary corporation of the International Conference of Building Officials EVALUATION REPORT Copyright 2001 ICBO
More informationArchitectural Single-Hung Aluminum Window Series L701T SH-AW130 GUIDE SPECIFICATION
Architectural Single-Hung Aluminum Window Series L701T SH-AW130 GUIDE SPECIFICATION Section 08520 Aluminum Windows PART 1: WORK INCLUDED A. The conditions of the contract and applicable sections of Division
More information1. Hangers and supports for electrical equipment and systems. 2. Construction requirements for concrete bases.
SECTION 260529 - HANGERS AND SUPPORTS PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Hangers and supports for electrical equipment and systems. 2. Construction requirements for concrete bases. 1.2
More informationDBI-SALA Uni 8 Overhead Horizontal Lifeline Cable System SECTION HORIZONTAL FALL PROTECTION - OVERHEAD CABLE
SECTION 112429.18 - HORIZONTAL FALL PROTECTION - OVERHEAD CABLE PART 1 - GENERAL 1.1 SECTION INCLUDES A. Provide overhead horizontal cable fall protection system, including end anchors, energy absorbers,
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 26 0526 - GROUNDING AND BONDING FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationSECTION SLUICE GATES
SECTION 11100 SLUICE GATES PART 1--GENERAL Fill in the blank with a short description of sluice gate usage, i.e., for isolation of wastewater, or for tank drainage, or for control of water surface. 1.01
More informationELECTRICAL CONTRACTORS THE UNIVERSITY OF TENNESSEE KNOXVILLE, TENNESSEE SECTION PAGE 1 SECTION EXTERIOR ATHLETIC LIGHTING
KNOXVILLE, TENNESSEE SECTION 16461 PAGE 1 SECTION 16526 EXTERIOR ATHLETIC LIGHTING 1PART - LIGHTING PERFORMANCE The lighting systems manufacturer shall supply equipment to meet or exceed the following
More informationSECTION VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions, apply to this Section. 1.2 SUMMARY A. This Section includes the
More informationThis product specification is written according to the Construction Specifications Institute MasterFormat, 2014 Update.
Kaf-Tech Product Specification This product specification is written according to the Construction Specifications Institute MasterFormat, 2014 Update. SECTION 260519 METAL CLAD CABLE - MC-PLUS Neutral
More informationE-Series Steel Gantry Crane
SPANCO PRODUCT SPECIFICATIONS 1 E-Series Steel Gantry Crane This guide can be used to prepare a bid specification for the incorporation of an E-Series Gantry Crane into a competitive bid project or application.
More informationSection SECTIONAL INSULATED STEEL DOORS
1 GENERAL 1.1 GENERAL REQUIREMENTS General Conditions and Division 01 apply to this section. 1.2 RELATED WORK Section 05500: Miscellaneous Metal Fabrication Section 07900: Joint Sealers Section 09900:
More informationSeries - 1
SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word
More informationSECTION VIBRATION CONTROLS FOR HVAC PIPING AND EQUIPMENT
SECTION 230548 - PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Elastomeric Isolation pads. 2. Elastomeric Isolation mounts. 3. [Freestanding] [Restrained] [Freestanding and restrained]
More informationMETAL HANDRAILS AND RAILINGS. A. Properly identified manufacturer's literature, including shop and erection drawings before starting work.
SECTION 05520 METAL HANDRAILS AND RAILINGS PART 1 GENERAL 1.01 SUBMITTALS A. Properly identified manufacturer's literature, including shop and erection drawings before starting work. B. Railing Assemblies
More informationNorthpointe Renovation EPN #1701 F/A Project #17027 September 8, 2017
SECTION 055213 - PIPE AND TUBE RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION HEAVY GLASS TOP HUNG SLIDING BI-FOLD DOOR SYSTEMS
Page 1 of 6 SECTION 08 32 20 HEAVY GLASS TOP HUNG SLIDING BI-FOLD DOOR SYSTEMS USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED BI-FOLD GLASS PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,
More informationSECTION PANEL AND POST AND PYLON SIGNAGE. 1. Non-illuminated Panel and Post signs. 2. Internal illumination Pylon (Cabinet and Post) signs.
PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Non-illuminated Panel and Post signs. 2. Internal illumination Pylon (Cabinet and Post) signs. 1.2 PERFORMANCE REQUIREMENTS A. Structural
More informationSECTION ROLLER GATES
GENERAL SUMMARY A. The Contractor shall provide all labor, materials, equipment, and incidentals required to furnish and install roller gates, complete and operational with all necessary accessories as
More informationSECTION BASIC ELECTRICAL MATERIALS AND METHODS
SECTION 26 05 05 BASIC ELECTRICAL MATERIALS PART 1 - GENERAL 1.1 SUMMARY A. Section includes the limited scope construction materials and methods for application with electrical installations as follows:
More information2. Cab, interior finishes, control panel and facings including cab doors. 3. Fire rated hoistway doors, sills, and frames.
PART 1: GENERAL 1.01 Summary Section Includes: 1. Electric traction Dumbwaiter system. 2. Cab, interior finishes, control panel and facings including cab doors. 3. Fire rated hoistway doors, sills, and
More informationDiffused Aeration Piping Equipment
1.0 General 1.1. The specifications in this section include all components of the Diffused Aeration System with the exception of the individual diffuser units. Refer to additional specification sections
More informationTRANSPORT II " 10.5" MOUNTING POSTS FENCE LINE POST. Classic gate shown GATE OPENING CANTILEVER GATE SAFETY WARNING
TRANSPORT ESTATE TRANSPORT IS TRANSPORT LINK ADAPTRACK 2"sq x.25" UPRIGHTS & DIAGONAL BRACES 1"sq x.125" PICKETS GATE TRACKS PRE-DRILLED FOR LEFT OR RIGHT OPENINGS FENCE LINE POST 13.8125" 10.5" MOUNTING
More information2000-SG STAINLESS STEEL SLIDE GATES
2000-SG STAINLESS STEEL SLIDE GATES 1. GENERAL CONDITIONS 1.1. SCOPE. This section covers Stainless Steel Flow Control Slide Gates and operators. 1.2. GENERAL. Slide gates, including actuation devices,
More informationPIPE AND TUBE RAILINGS
SECTION 05521 - PIPE AND TUBE RAILINGS PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationWestgate Entrematic, Parking Security Gates Section OVERHEAD SECURITY GATE Prepared by: Digicon Information Inc. Page 1
Prepared by: Digicon Information Inc. Page 1 This section includes overhead type Parking Security Gates, as manufactured by Westgate Entrematic, a division of Helton Group of Companies. DISCLAIMER: This
More informationAttachment A-Flagpole(s) Specifications
Attachment A-Flagpole(s) Specifications PART 1-GENERAL 1.1 SCOPE A. The scope of work includes the removal of existing flagpole(s) and associated concrete bases, and installation of a new flagpole(s) and
More informationSST-II HYDRAULIC BI-FOLD SPECIFICATIONS
PART 1 GENERAL 1.01 DESCRIPTION A. General 1. Furnish SST-II Hydraulic Bi-Fold System complete from one manufacturer. Provide all labor, materials, tools and equipment to furnish the SST-II Bi-Fold System
More informationOptics Mounting Lamping Finish Voltage Options. T6 Metal Halide* H039T6 1 39wT6 H070T6 2 70wT6. H w H070 70w H w
Quadro Project: Type: Qty: QD _ Series Optics Mounting Lamping Finish Voltage _ Option Pole Series Height Finish Options Series QD Quadro Optics Mounting Lamping Finish Voltage Options MA Type III MTR
More informationSIERRA MODEL 12 X 24 SPECIFICATIONS
SIERRA MODEL 12 X 24 SPECIFICATIONS Dimensions: Roof Dimensions 12-0 x 24-0 Column Dimensions (center to center) 9-0 x 21-0 Minimum Clearance 8-0 Shed Roof 1:12 pitch Square Feet Under Roof 288 Columns
More informationINSTALLATION INSTRUCTIONS FOR ELECTRICAL CONTRACTORS
INSTALLATION INSTRUCTIONS FOR ELECTRICAL CONTRACTORS Rev. 1.5 1.10.13 Toll free (800) 288-6000 or www.hubbell-wiring.com P a g e 0 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING- When using
More informationSECTION REINFORCING STEEL
SECTION REINFORCING STEEL 1. DESCRIPTION This specification shall govern the furnishing and placing of reinforcing steel, deformed and smooth, of the size and quantity designated on the plans and in accordance
More informationSECTION ENTRANCE FLOOR GRILLES STAINLESS STEEL GRATING
7160 Krick Rd., Walton Hills, OH 44146 800-321-3827 - Tel 440-439-8650 - Fax 440-439-6889 SECTION 12 48 16 ENTRANCE FLOOR GRILLES STAINLESS STEEL GRATING PART 1. GENERAL 1.01 SUMMARY: This section includes
More informationSECTION SECTIONAL OVERHEAD DOORS 522 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS. Display hidden notes to specifier. (Don't know how?
SECTION 08360 SECTIONAL OVERHEAD DOORS 522 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Glazed Aluminum
More informationREV. 9/08. Mounting Structure PRE-INSTALLATION GUIDE for Ergon Skybooms
REV. 9/08 Mounting Structure PRE-INSTALLATION GUIDE for Ergon Skybooms SKYTRON MOUNTING STRUCTURES for Ceiling Mounted Equipment Foreword Skytron s objective is to provide a program and guideline to assist
More informationSECTION SLOPED TRANSLUCENT METAL SKYLIGHT SYSTEM
PART 1- GENERAL 1.1 SUMMARY A. Section Includes: SECTION 084523 - SLOPED TRANSLUCENT METAL SKYLIGHT SYSTEM 1. Flat factory prefabricated structural insulated translucent sandwich panels; with glazed endwalls.
More informationCentral Dartmouth Section Exterior Envelope Renovations METAL-CLAD WOOD DOORS Page 1 of 5 Dartmouth, NS
Exterior Envelope Renovations METAL-CLAD WOOD DOORS Page 1 of 5 Part 1 General 1. RELATED SECTIONS 1. Section 07 92 10 Joint Sealing 2. Section 08 71 00 Door Hardware 2. REFERENCES 1. American Society
More informationA. Access doors and frames are part of an access door and frame allowance.
SECTION 08 31 13 ACCESS DOORS AND FRAMES PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationTitle: YALE OFFICE OF FACILITIES PROCEDURE MANUAL Chapter: 01 - Yale Design Standard Division: Electrical Standards
Date Description of Change Pages / Sections Modified ID 6/15/16 Updated format, division title, and removed references to other sections. - mgl44 A. Summary This section contains design criteria for the
More informationMERCHANTS METALS. A. ASTM F552 Standard Terminology Relating to Chain Link Fencing
MERCHANTS METALS SECTION 32 31 13 COLORBOND CHAIN LINK FENCE AND GATES 2014 PART 1 GENERAL 1.1 RELATED DOCUMENTS A. DIVISION 01 - GENERAL REQUIREMENTS: Drawings, quality, product and performance requirements,
More informationSection 906. STRUCTURAL STEEL
906.01 Section 906. STRUCTURAL STEEL 906.01. General Requirements. Finished rolled shapes must be free from imperfections that affect strength and durability in accordance with ASTM A 6. Rolled shapes
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 12 2113 - LOUVER BLINDS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationPRODUCT SPECIFICATIONS
PART 1 GENERAL 1.01 SUMMARY A. Section Includes: High density cast resin architectural products, including columns, panels, caps, bases, trim elements and balustrade systems. Specifier Note: Article below
More informationMCINTOSH COUNTY SCHOOLS TODD GRANT (K-5) SCHOOL DEMOLITION AND FINISHED SITE WORK
MCINTOSH COUNTY SCHOOLS TODD GRANT (K-5) SCHOOL DEMOLITION AND FINISHED SITE WORK ADDENDUM NO. 2 DATE: April 18, 2016 John A. Tuten & Associates, Inc. 4680 Hwy 17 North Brunswick, GA 31525 PROJECT MANUAL
More informationA. This Section includes automatic entrance door systems operating as follows: 1. Swinging operation.
SECTION 08462 - SWINGING AUTOMATIC ENTRANCE DOORS PART 1 - GENERAL.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General, Supplementary, and Special Conditions and Division
More informationA. Submit the following in addition to the standard requirements.
SECTION [13120] OMNIFLEX 300 MODULAR WALL SYSTEM SECTION 1 GENERAL 1.01 SECTION INCLUDES A. This Section specifies all requirements necessary to furnish and install a complete modular wall system including,
More informationSECTION DECORATIVE METAL AND GLASS RAILING
SECTION 05 73 00 DECORATIVE METAL AND GLASS RAILING PART 1 GENERAL 1.1 SUMMARY A) This section includes both standard and custom handrails as shown in the contract drawings. B) These include aluminum,
More informationSECTION PACKAGE BOOSTER PUMP STATIONS
SECTION 331223 PACKAGE BOOSTER PUMP STATIONS Scope: The Contractor shall install a pump station at two locations to be determined by the Owner. These pump stations shall be designed to deliver flow to
More informationService Entrance Cable Fittings
Suggested Specifications for Service Entrance Fittings All service fittings shall be approved for the purpose by a nationally recognized testing laboratory, inspection agency or product evaluation organization.
More informationCHAIN LINK FENCES AND GATES
SECTION 02831 CHAIN LINK FENCES AND GATES PART 1 GENERAL 1.01 SUMMARY A. Alternate Material for Fence Post and Framing Material: Where schedule 40 galvanized steel is specified, the following will be accepted:
More informationPASSAIC COUNTY TECHNICAL INSTITUTE CCA 1422 NEW S.T.E.M. BUILDING 2017
SECTION 10505 - METAL STUDENT LOCKERS PART 1 - GENERAL 1.01 SCOPE OF WORK A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationG. UNDERWRITERS LABORATORY, INC.: 1. UL 325: Electrical Door, Drapery, Gate, Louver, and Window Operators and Systems
B6.0 DIVISION 8 - DOORS AND WINDOWS SECTION 08460 - AUTOMATIC ENTRANCE DOORS Specifier Note: Coordinate and edit articles and paragraphs below to suit project requirements. Add section numbers and titles
More informationGUIDE SPECIFICATION EXETER VERSA SHIELD SECURITY SCREEN SYSTEM
1 GUIDE SPECIFICATION EXETER VERSA SHIELD SECURITY SCREEN SYSTEM 1.01 WORK INCLUDED PART 1: GENERAL A. Provide for all labor, equipment, materials, and services to furnish and install VERSA SHIELD Window
More informationSPECIFICATION SECTION 05515: LADDERS O Keeffe s Aluminum Ladders
Welcome to the O Keeffe s Guide Specification System prepared as an aid to specify in preparing written construction documents. For specification assistance with specific product applications, please contact
More informationSECTION SECTIONAL OVERHEAD DOORS
SECTION 08360 SECTIONAL OVERHEAD DOORS PART 1 GENERAL PART 1.1 SECTION INCLUDES A. Overhead doors. B. Bi-fold doors. PART 1.2 RELATED SECTIONS A. Section 03300 - Cast-In-Place Concrete: Prepared opening
More informationSignature Series 5 Lap SECTION ALUMINUM WINDOWS
Signature Series 5 Lap SECTION 08 51 13 ALUMINUM WINDOWS PART 1 GENERAL 1.01 SUMMARY A. Related Documents: Conditions of the Contract, Division 1 - General Requirements, and Drawings apply to Work of this
More informationSECTION ORNAMENTAL HANDRAILS AND RAILINGS
SECTION 05720 PART 1 - GENERAL ORNAMENTAL HANDRAILS AND RAILINGS 1.1 SUMMARY A. Section Includes: 1. Ornamental Handrails and Railings. 2. Glazed Panel Railings. 1.2 DEFINITIONS A. Guardrail: System of
More informationSECTION ORNAMENTAL ALUMINUM RAILING. ** NOTE TO SPECIFIER ** Superior Aluminum Products, Inc.; Ornamental aluminum railing products.
SECTION 05720 ORNAMENTAL ALUMINUM RAILING ** NOTE TO SPECIFIER ** Superior Aluminum Products, Inc.; Ornamental aluminum railing products. This section is based on the products of Superior Aluminum Products,
More information800 Series Aluminum Overhead Doors, by Northwest Door Section ALUMINUM SECTIONAL DOORS Digicon Information Inc.
Digicon Information Inc. Page 1 This section includes Model 800 aluminum insulated overhead sectional doors manufactured by Northwest Doors, with manual, chain or electric operation, with our without windows.
More informationSECTION RADIO FREQUENCY SHIELDING ENCLOSURE RF Welded System
SECTION 13096 RADIO FREQUENCY SHIELDING ENCLOSURE RF Welded System Prepared by: 90 Dayton Avenue, Unit 4B, Suite 13 Passaic, NJ 07055 (973) 574-9077 13096-1 RF WELDED SYSTEM PART 1 GENERAL 1.1 SECTION
More informationSection BUILDINGS, SHELTERS, ENCLOSURES
Section 13121 BUILDINGS, SHELTERS, ENCLOSURES Part 1 GENERAL 1.1 SECTION INCLUDES 1.2 A. Pre-engineered buildings. B. Pre-engineered shelters. C. Pre-engineered enclosures. D. Electrical wiring and devices
More informationADDENDUM No. 6. ITB No. 4424: W.R. Wheeler (Swift Run) Service Center PUD Non-motorized Improvements Phase 1
ADDENDUM No. 6 ITB No. 4424: W.R. Wheeler (Swift Run) Service Center PUD Non-motorized Improvements Phase 1 Due: June 9, 2016 at 2:00 p.m. (local time) The following changes, additions, and/or deletions
More informationSECTION CHAIN LINK FENCES AND GATES
SECTION 32 31 13 SPEC WRITER NOTES: Use this section only for NCA projects. Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section
More informationSECTION PREFABRICATED PIPE BRIDGE(s)
SECTION 13135 - PREFABRICATED PIPE BRIDGE(s) PART 1 - GENERAL 1.01 Scope A. The Contractor is responsible for all engineering design, detailing, fabricating, installation including foundations for the
More informationUFGS (April 2006) UNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-08 11 73 (January 2007) ---------------------------- Preparing Activity: NAVFAC Replacing without change UFGS-08 11 73 (April 2006) UNIFIED FACILITIES GUIDE SPECIFICATIONS
More informationWelcome to Douglas County PUD
Welcome to Douglas County PUD We are committed to providing the best possible utility services at the lowest possible cost consistent with sound business principles. To better serve you, please fill out
More informationSECTION ACOUSTICAL PANEL CEILINGS
SECTION 095113 ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationThe following document can be provided to an Engineer, Contractor, or Owner to allow them to
MESAN series MXL Engineering Guide Specifications The following document can be provided to an Engineer, Contractor, or Owner to allow them to properly specify MESAN s MXL series Cooling Towers. 15XXX-
More informationUNIVERSITY OF WASHINGTON Facilities Services Design Guide. Electrical. Medium Voltage Switchgear. Basis of Design.
Basis of Design This section applies to the design and selection of medium voltage switchgear, primarily for use in substations. Design Criteria 13.8kV equipment shall be 15kV class, 4.16kV and 2.4kV equipment
More informationSECTION LIGHTING
PART 1 - GENERAL 1.1. RELATED SECTIONS: 1.2. SCOPE OF SECTION: This section contains the requirements for equipment and installation related to exterior, interior, and special lighting applications. 1.3
More informationSECTION METAL MATERIALS, METHODS AND FASTENING
PART 1 - GENERAL 1.01 DESCRIPTION SECTION 05025 METAL MATERIALS, METHODS AND FASTENING Work Specified Herein and Elsewhere: A. This Section includes the basic materials and methods required for the work
More information