FACT SHEET CPC CERTIFICATE III IN WALL AND CEILING LINING

Transcription

1 FACT SHEET CPC CERTIFICATE III IN WALL AND CEILING LINING This program covers building construction theory and practices related to low rise buildings. This program will provide you with the knowledge and skills to meet the technical qualifications for the qualification of Wall and Ceiling Lining. Completion of the general induction training program specified by the National Code of Practice for Induction Training for Construction Work (ASCC 2007) is required before entering a construction work site. Achievement of unit CPCCOHS1001A covers this requirement. Qualification Pathways Entry Requirements Study Duration and Enrolment Periods Mode of Delivery Cost Upon successful completion of this qualification you will receive a Certificate III in Wall and Ceiling Lining CPC After successful completion of CPC31211 Certificate III in Wall and Ceiling Lining, you may continue with your studies by enrolling in: Managerial Course: (NOTE: BSBSMB401A Establish legal and risk management requirements of small business can be taken as an Elective in CPC31211 Certificate III in Wall and Ceiling Lining as assisting in starting up your Plastering business). Queensland specific. CPC40110 Certificate IV in Building & Construction (Building). (One Certificate III competency counts towards the Certificate IV program) (Builder Low Rise license - QLD only) CPC50210 Diploma of Building & Construction (Building) (Building Practitioner Registration Western Australia only) CPC50210 Diploma of Building & Construction (Building) (Builder Medium Rise license - QLD only) Career opportunities include employment as a: Wall and ceiling liner This qualification does not have any specific entry requirements. However, completion of Year 12 English and Mathematics is recommended. Enrolments are taken on an ongoing basis. Students can enrol at any time 24/7 online, over the phone or in person during business hours. Enrolment is for a period of 12 months. NOTE: Keystone Training delivers this qualification by Recognition of Prior Learning (RPL) and/or Gap Training - NOT FULL TRAINING. The candidate requires a minimum of 3 to 4 years experience within this trade. (Please enquire for verification). Flexible Delivery - Online with face to face/phone/ /online Tutorial support, Face to Face, Distance delivery with face to face/phone/ /online Tutorial. NOTE: Practical training consists of On the Job training and applicants who wish to train with Keystone Training MUST have access to all physical resources. All enrolment fees are inclusive for RPL, learner resources, assessment trainer tutorials, access to internet and issuing of qualification. Please to the Price List section for fee structure. This Document is a controlled document and becomes uncontrolled when downloaded or reproduced. Page 1 of 12

2 How to Enrol Recognition of Prior Learning Credit Transfers Learning Support Work Health & Safety Contact Us NOTE: This program is conducted by a combination of RPL and gap training. To enrol in this mode of delivery and assessment you MUST be currently working in the building and construction industry performing construction type work with a minimum of 3 to 4 years current experience. NOTE: Practical Training consists of On the Job gap training and therefore applicants who wish to train with Keystone Training MUST have access to all physical resources. To enrol in this qualification please contact Keystone Training. Prior to enrolment a copy of the Student Handbook is available via download or via contacting our office. Applicants may receive acknowledgment of their knowledge and experiences through RPL. Evidence for RPL may include: work experience life experiences (including voluntary work and leisure pursuits) previous study e.g. qualifications, industry training professional development programs or units The matrix below is a guide for previously gained units of competency in CPC Keystone Training supports many learning needs. Reasonable adjustments can be made to assist students in achieving a competent result where learning difficulties may be present. For students needing additional Language, Literacy and Numeracy support Keystone recommends Fruition Tuition contact details are contact no Keystone Training offers support via many modes including face to face tutorials, Skype, and phone. Refer to the Student Handbook for detailed information on support offered by Keystone Training. Please note that CPC31211 Certificate III in Wall and Ceiling Lining has practical units requiring field work (On the Job), therefore students must have access to the appropriate personal protective equipment to perform all practical tasks. If you would like additional information about this qualification, or about any of the wide range of qualifications offered by Keystone Training, you can visit our website or contact us via: Office: Monday to Friday: 8.30am to 4.30pm; Fax: (07) Street Address: Units 36 & 37, 17 Cairns Street, Loganholme 4129 Postal Address: PO Box 4262, Eight Mile Plains QLD admin@keystonetraining.com.au To Achieve the Qualification CPC31211 CERTIFICATE III IN WALL AND CEILING LINING requires the successful completion of ALL 19 Core & 7 Elective Units of Competency (26 in Total) listed in COLUMN 1. This Document is a controlled document and becomes uncontrolled when downloaded or reproduced. Page 2 of 12

3 TRANSFER & ELIGIBILITY FOR in CPC31211 Certificate III in Wall and Ceiling Lining. If you have successfully completed ANY of the following Units of Competency or Qualifications listed in columns 3 OR 4 and you can produce copies of your qualification you will NOT have to enrol in the corresponding Unit of Competency in COLUMN 1 to complete the full Qualification because you will be given Credit for that Unit. Evidence of your Qualification could include: Certificates and Academic Transcripts from the Registered Training Organisation who issued the qualification. NOTE: You cannot Credit Transfer in ALL of the Qualification; a minimum of ONE Unit MUST be Completed to achieve the Qualification (Contact Keystone Training to discuss the one Unit to enrol in). This Document is a controlled document and becomes uncontrolled when downloaded or reproduced. Page 3 of 12

4 CORE UNITS in CPC31211 UNIT OUTLINE TRANSFER ELIGIBLE CPCCCM1012A Work effectively and sustainably in the construction industry CPCCCM1013A Plan and organise work CPCCCM1014A Conduct workplace communication CPCCCM1015A Carry out measurements and calculations CPCCCM2001A Read and interpret plans and specifications CPCCCM2010B Work safely at heights outcomes required to prepare for and sustain effective work within the construction industry. It covers the identification and clarification of the construction industry work context, scope and employment conditions, responsibility required to be accepted by the individual, working in a team, individual career path improvement activities and sustainable work practices and techniques. outcomes required to plan and organise individual and group work activities on a construction site. The unit includes identifying task requirements, planning steps and organising work. outcomes required to communicate effectively with other workers in a construction workplace environment. It includes gathering, conveying and receiving information through verbal and written forms of communication. outcomes required to carry out measurements and perform simple calculations to determine task and material requirements for a job in a construction work environment. outcomes required to read and interpret plans and specifications relevant to construction operations. It includes the identification of types of plans and drawings and their functions, the recognition of commonly used symbols and abbreviations, the identification of key features and specifications on a site plan, the comprehension of written job specifications and the recognition of document status and amendment detail. outcomes required to work safely on construction sites where the work activity involves working above 1.5 metres from ground level and where CPCCCM1002A Work effectively and sustainably in the construction industry CPCCCM1003A Plan and organise work CPCCCM1004A Conduct workplace communication CPCCCM1005A Carry out measurements and calculations CPCCCM2001A Read and interpret plans and specifications CPCCCM2010B Work safely at heights; OR CPCCCM2010A Work safely at This Document is a controlled document and becomes uncontrolled when downloaded or reproduced. Page 4 of 12

5 CORE UNITS in CPC31211 UNIT OUTLINE TRANSFER ELIGIBLE Fixing (hanging) field of work CPCCPB3001A Fix standard plasterboard wall sheets CPCCPB3002A Fix standard plasterboard ceiling sheets CPCCPB3003A Fix battens CPCCPB3004A Fix wet area sheets CPCCPB3005A Fix ceiling sheets to external protected areas CPCCPB3006A Fix fibre cement board fall protection measures are required. outcomes required to fix standard plasterboard wall sheets to comply with manufacturer and job specifications. outcomes required to fix standard plasterboard ceiling sheets to comply with manufacturer and job specifications. outcomes required to fix battens to ceiling joists or roof trusses when preparing to fix ceiling system sheets. outcomes required to fix wet area sheets to comply with manufacturer and job specifications. outcomes required to fix ceiling sheets to external protected areas to comply with manufacturer and job specifications. outcomes required to fix fibre cement board to comply with manufacturer and job specifications. Finishing (stopping, sanding and cornices) field of work CPCCPB3007A Apply levels of finish standards to planning and inspection of own work CPCCPB3008A Mix plastering compounds CPCCPB3009A Finish plasterboard joins manually outcomes required to identify the level of finish standards and their application to the planning and inspection of own work. outcomes required to mix plastering compounds using hand or mechanical mixing techniques. outcomes required to finish plasterboard joins to comply with manufacturer instructions, job specifications and Australian standards. heights CPCCPB3001A Fix standard plasterboard wall sheets CPCCPB3002A Fix standard plasterboard ceiling sheets CPCCPB3003A Fix battens CPCCPB3004A Fix wet area sheets CPCCPB3005A Fix ceiling sheets to external protected areas CPCCPB3006A Fix fibre cement board CPCCPB3001A Fix standard plasterboard wall sheets CPCCPB3002A Fix standard plasterboard ceiling sheets CPCCPB3003A Fix battens This Document is a controlled document and becomes uncontrolled when downloaded or reproduced. Page 5 of 12

6 CORE UNITS in CPC31211 UNIT OUTLINE TRANSFER ELIGIBLE CPCCPB3010A Manually sand plaster work outcomes required to hand sand joins in plaster walls, ceilings or cornices. CPCCPB3004A Fix wet area sheets CPCCPB3011A Finish category 1 and 2 wet areas outcomes required to finish wet area systems to comply with manufacturer's instructions, job specifications and Australian standards. CPCCPB3005A Fix ceiling sheets to external protected areas CPCCPB3012A Cut and fix paperfaced cornices outcomes required to measure, cut and fix paper-faced cornices. CPCCPB3006A Fix fibre cement board This Document is a controlled document and becomes uncontrolled when downloaded or reproduced. Page 6 of 12

7 ELECTIVE UNIT DETAILS Elective units Unit outline Credit Transfer Eligible Elective units (7 Electives required) Commercial wall and ceiling lining field of work CPCCCA3014A Construct bulkheads CPCCCA3015A Assemble partitions CPCCCM2006B Apply basic levelling procedures outcomes required to construct bulkheads to conceal services or for decorative purposes. It includes straight, curved and geometric shaped bulkheads, generally constructed in situ and includes prefabricated fitments. outcomes required to set out and assemble partitions for the purpose of dividing areas into useable spaces. It includes prefabricated and demountable partitions constructed of timber or metal. outcomes required to carry out levelling in a single plane for the purposes of establishing correct and accurate set of building components. It includes the set up, testing and use of levelling devices, and establishing and transferring heights using a range of levelling equipment. CPCCCA3014A Construct bulkheads CPCCCA3015A Assemble partitions CPCCCM2006B Apply basic levelling procedures; OR CPCCCM2006A Apply basic levelling procedures A maximum of two of the seven required elective units may be substituted by selecting relevant units of competency from any Certificate III or IV construction qualification or qualification in another endorsed Training Package. This Document is a controlled document and becomes uncontrolled when downloaded or reproduced. Page 7 of 12

8 Elective units Unit outline Credit Transfer Eligible CPCCCM2007B Use explosive power tools CPCCWC3001A Install and finish plasterboard and fibre cement sheeting to curved walls and ceilings CPCCWC3003A Install dry wall passive fire-rated systems CPCCWC3004A Install suspended ceilings Plasterboard handling field of work CPCCPB3023A Load and unload plaster and plasterrelated CPCCPB3024A Use manual handling equipment to manoeuvre plaster outcomes required to apply safe and effective operation of explosive power tools (EPT), used to fasten materials or fix fasteners to bases. It includes both direct action and indirect action explosive powered fastening tools. outcomes required to fix and finish plasterboard and fibre cement sheeting to steel and timber framed curved walls and curved ceilings. the work, preparation of the work area for the installation process, measuring and cutting the material, fixing the material, jointing and finishing, and completion of post work clean-up activities. outcomes required to select and install dry wall fire-rated systems to walls and ceilings. installation; installation of approved systems for timber stud walls, steel stud partitions, shaft walls, timber joist and suspended ceilings; and completion of post-installation activities. outcomes required to install exposed and concealed suspended ceilings. work; set-out and installation of the ceiling suspension system; installation of lining material; and completion of clean-up activities. outcomes required to identify critical characteristics of plaster loads and to safely load and unload plaster and plaster-related in accordance with workplace requirements and relevant government regulations. outcomes required to use mechanical aids in the shifting of loads. CPCCCM2007B Use explosive power tools; OR CPCCCM2007A Use explosive power tools CPCCWC3001A Install and finish plasterboard and fibre cement sheeting to curved walls and ceilings CPCCWC3003A Install dry wall passive fire-rated systems CPCCWC3004A Install suspended ceilings CPCCPB3023A Load and unload plaster and plaster-related CPCCPB3024A Use manual handling equipment to manoeuvre plaster This Document is a controlled document and becomes uncontrolled when downloaded or reproduced. Page 8 of 12

9 Elective units Unit outline Credit Transfer Eligible CPCCPB3025A Store plasterboard and related General Electives BSBSMB301A Investigate micro business opportunities BSBSMB406A Manage small business finances CPCCCA3001A Carry out general demolition of minor building structures CPCCCM2008B Erect and dismantle restricted height scaffolding CPCCCM3001C Operate elevated work platforms outcomes required to store plaster and plaster on site or in warehouses. This unit describes the performance outcomes, skills and knowledge required to develop business ideas, and to investigate market needs and factors affecting potential markets. Specific legal requirements apply to the management of a micro business. This unit describes the performance outcomes, skills and knowledge required to implement, monitor and review strategies for the ongoing management of a small business's finances. It also includes day to day financial management of the small business. Specific legal requirements apply to the management of a small business. outcomes required to carry out general demolition work of minor building structures to facilitate alterations, extensions and additions to a building. It includes work being completed to a work schedule, plans and specifications. outcomes required to erect and dismantle restricted height scaffolding to provide work platforms for various occupational applications. It includes placement of safety barriers and only involves modular scaffolding restricted to a height of 4 metres. outcomes required to safely and effectively operate some types of elevated work platforms (EWPs) in a variety of different terrains and situations to access isolated work areas. The unit includes locating, setting up, operating and shutting down EWPs. CPCCPB3025A Store plasterboard and related BSBSMB301A Investigate micro business opportunities BSBSMB406A Manage small business finances CPCCCA3001A Carry out general demolition of minor building structures CPCCCM2008B Erect and dismantle restricted height scaffolding; OR CPCCCM2008A Erect and dismantle restricted height scaffolding CPCCCM3001C Operate elevated work platforms; OR CPCCCM3001B Operate elevated work platforms This Document is a controlled document and becomes uncontrolled when downloaded or reproduced. Page 9 of 12

10 Elective units Unit outline Credit Transfer Eligible CPCCPB3013A Plan travel routes CPCCPB3014A Install batt insulation CPCCPB3015A Install acoustic and thermal environmental protection systems CPCCPB3016A Install and finish columns CPCCPB3017A Rectify faults in plaster applications CPCCPB3018A Use vacuum and electric sanding equipment to finish plaster work CPCCPB3019A Inspect equipment for serviceability CPCCPB3020A Match, mitre and install cast ornamental cornices CPCCPB3021A Install and fix residential acoustic plaster outcomes required to transport self and others, or deliver product, to the work site. outcomes required to install thermal and acoustic insulation to comply with manufacturer and job specifications. outcomes required to install wall and ceiling systems that satisfy environmental requirements in terms of acoustic ratings and energy efficiency ratings in accordance with sustainable building practices. work, installation of insulation to wall cavities and plenum, installation of acoustic systems and completion of post work clean-up activities. outcomes required to install columns to comply with customer orders, manufacturer's instructions, contractual requirements, specifications and Australian standards. outcomes required to identify faults and causes of faults in plasterboard applications and to rectify the faults. outcomes required to machine sand plaster joins in walls and ceilings. outcomes required for equipment users to inspect and report on the safety and operational effectiveness of equipment. outcomes required to measure, match, cut and fix cast ornamental cornices. outcomes required to install residential acoustic plaster systems under direction. CPCCPB3013A Plan travel routes CPCCPB3014A Install batt insulation CPCCPB3015A Install acoustic and thermal environmental protection systems CPCCPB3016A Install and finish columns CPCCPB3017A Rectify faults in plaster applications CPCCPB3018A Use vacuum and electric sanding equipment to finish plaster work CPCCPB3019A Inspect equipment for serviceability CPCCPB3020A Match, mitre and install cast ornamental cornices CPCCPB3021A Install and fix residential acoustic plaster This Document is a controlled document and becomes uncontrolled when downloaded or reproduced. Page 10 of 12

11 Elective units Unit outline Credit Transfer Eligible CPCCPB3022A Use mechanical jointing equipment to finish joints CPCCPB3026B Erect and maintain trestle and plank systems CPCCPB3027A Install ceiling insulation CPCCSP3003A Apply trowelled texture coat finishes CPCCSP3005A Install pre-cast decorative mouldings CPCCWC2001A Complete penetrations and flashings outcomes required to use mechanical taping and filling tools to finish joints. outcomes required to erect and monitor trestle and plank work platforms. outcomes required to install ceiling insulation to comply with safety requirements as well as environmental requirements for energy efficiency ratings in accordance with sustainable building practices. It includes identifying and complying with applicable legislative requirements, planning and preparing for work, installing ceiling insulation, and completing installation and post-work clean-up activities. outcomes required to mix and apply trowelled texture coat finishes. the work; preparation of the background surface; mixing, application and finishing of the texture coats; and completion of clean-up activities. outcomes required to install pre-cast decorative mouldings to masonry, plasterboard and fibre cement sheets. work; preparation of the work area; measuring, cutting and fixing of cast plaster; finishing junctions for painting; and completion of post work clean-up activities. outcomes required to complete the penetrations and flashings associated with wall and ceiling lining. It does not cover the technical aspects of passive fire systems. CPCCPB3022A Use mechanical jointing equipment to finish joints CPCCPB3026B Erect and maintain trestle and plank systems; OR CPCCPB3026A Erect and maintain trestle and plank systems CPCCPB3027A Install ceiling insulation CPCCSP3003A Apply trowelled texture coat finishes CPCCSP3005A Install pre-cast decorative mouldings CPCCWC2001A Complete penetrations and flashings This Document is a controlled document and becomes uncontrolled when downloaded or reproduced. Page 11 of 12

12 Elective units Unit outline Credit Transfer Eligible CPCCWC3002A Install and finish plasterboard and fibre cement sheeting to arches CPPCMN3001B Participate in environmentally sustainable work practices BSBSMB401A Establish legal and risk management requirements of small business work, selection and safe use of tools and equipment to complete the penetrations and flashings, restoration of the integrity of the wall or ceiling, and completion of post work clean-up activities. outcomes required to fix and finish plasterboard and fibre cement sheeting to arches. It includes the planning and preparation for the work, the preparation of the work area for the installation process, the measuring and cutting of the material, the fixing of the material, the jointing and finishing and the completion of post work clean-up. outcomes required to participate in environmentally sustainable work practices. The unit requires the ability to identify current resource usage in the workplace and contribute to ensuring compliance with legislative requirements. It also requires the capacity to contribute to improvements in sustainable work practices. It is essential that the organisation s approach to ensuring environmentally sustainable work practices, and the benefits that they bring, are understood. The unit must be applied strictly according to relevant state or territory legislative and industry requirements. This unit describes the performance outcomes, skills and knowledge required to identify and comply with the regulatory, legal, taxation and insurance requirements, and risk management needs of small business. Specific legal requirements apply to the management of a small business. CPCCWC3002A Install and finish plasterboard and fibre cement sheeting to arches CPPCMN3001B Participate in environmentally sustainable work practices; OR CPPCMN3001A Participate in environmentally sustainable work practices BSBSMB401A Establish legal and risk management requirements of small business This Document is a controlled document and becomes uncontrolled when downloaded or reproduced. Page 12 of 12