April 30, 2015 PREPARED FOR: Stantec, Inc. 55 Green Mountain Drive South Burlington, VT 05403

Transcription

1 ASBESTOS INSPECTION REPORT 1079/ 1081, 1253 & 1371 Airport Drive, 3 & 4 Delaware Street, 53 North Henry Court, and 11 & 49 South Henry Court South Burlington, VT AIP 88 April 30, 2015 PREPARED FOR: Stantec, Inc. 55 Green Mountain Drive South Burlington, VT 05403

2 TABLE OF CONTENTS Page 1. INSPECTION SUMMARY 1 2. INSPECTION METHODS 2 3. VERMONT REGULATIONS FOR ASBESTOS CONTROL (VRAC) 2 4. CERTIFICATION/ACCREDITATION 2 5. INSPECTION RESULTS 3 6. OBSERVATIONS AND RECOMMENDATIONS 3 TABLE 1 - INSPECTION RESULTS 5 APPENDIX 1 - APPENDIX 2 - APPENDIX 3 KAS, INC. LICENSES/ CERTIFICATIONS LABORATORY ANALYSES RESULTS SITE SKETCH

3 KAS, Inc. April 30, 2015 Asbestos Site Inspection Report AIP INSPECTION SUMMARY Eight vacant single family homes located at 1079/ 1081, 1253 & 1371 Airport Drive, 3 & 4 Delaware Street, 53 North Henry Court, and 11 & 49 South Henry Court, South Burlington, Vermont were inspected for the presence of asbestos containing materials (ACMs) April 1-3, The inspections were predemolition inspections conducted to fulfill US EPA NESHAP requirements in accordance with 40 CFR Part 61 Subpart M and State of Vermont asbestos requirements in accordance with V.S.A. Title 18, Chapter 26. The inspections/sampling included obtaining bulk samples from suspect materials inside and out side the buildings. The inspections are believed to have reasonably determined the ACMs that exist in the buildings. 1079/ 1081 Airport Drive 17 different homogeneous suspect materials were identified and sampled in this house. Joint compound throughout the residence (2% Chrysotile), sink coating (2% Chrysotile) and Vermiculite insulation (assumed ACM) were determined to be ACM Airport Drive 19 different homogeneous suspect materials were identified and sampled in this house. Sheet flooring in the kitchen (20% Chrysotile), sheet flooring in the dining room (20% Chrysotile), sink coating (2% Chrysotlile) and window glaze on garage windows (3% Chrysotile) were determined to be ACM Airport Drive - 9 different homogeneous suspect materials were identified and sampled in this house. Chimney flashing (assumed ACM) was determined to be ACM. 3 Delaware Street - 14 different homogeneous suspect materials were identified and sampled in this house. Vinyl flooring in storage above basement (20% Chrysotile), floor tile in the basement (3% Chrysotile) and chimney flashing (5% Chrysotile) were determined to be ACM. 4 Delaware Street - 14 different homogeneous suspect materials were identified and sampled in this house. Sheet flooring in kitchen (15% Chrysotile), carpet mastic in living room (2% Chrysotile), caulking around chimney fluke (15% Chrysotlile), basement window glaze (2% Chrysotile) and chimney flashing (5% Chrysotile) were determined to be ACM. 53 North Henry Court- 15 different homogeneous suspect materials were identified and sampled in this house. Sheet flooring in kitchen (20% Chrysotile), mastic on insulation (3% Chrysotile) and chimney tar (8% Chrysotile) were determined to be ACM. 11 South Henry Court - 17 different homogeneous suspect materials were identified and sampled in this house. Chimney tar (5% Chrysotile) was determined to be ACM. 1

4 KAS, Inc. April 30, 2015 Asbestos Site Inspection Report AIP South Henry Court - 11 different homogeneous suspect materials were identified and sampled in this house. Composite flooring in kitchen (25% Chrysotile), sink coating (3% Chrysotile) and chimney flashing (5% Chrysotile) were determined to be ACM. A copy of this inspection report should be kept on site during demolitions. Table 1 summarizes the inspection results. 2. INSPECTION METHODS This asbestos site inspection was conducted by an EPA accredited, State of Vermont certified, Asbestos Inspectors/ Management Planners and EPA accredited, State of Vermont certified, Asbestos Inspectors generally in accordance with AHERA inspection guidelines and generally accepted procedures. Bulk sample analysis was conducted by a State of Vermont licensed laboratory, Schneider Laboratories Global, Inc., Richmond, VA. The asbestos inspection consisted of a visual and physical inspection. The entire interior and exterior of the buildings were inspected including opening cavities. Destructive demolition inspections were performed. In accordance with the workscope for this project, bulk samples were collected and analyzed from each suspect material found except chimney flashing at one location and Vermiculite insulation, when present, which has been assumed ACM in accordance with the latest EPA guidance. Bulk samples of suspect ACM were analyzed for asbestos content using PLM methods. 3. VERMONT REGULATIONS FOR ASBESTOS CONTROL (VRAC) The Vermont Regulations for Asbestos Control, as authorized by 18 VSA Chapter 26, detail the procedures, regulations, certifications and licenses required when disturbance of asbestos containing materials occurs in the State of Vermont. In essence, any company, individual or organization that disturbs asbestos containing materials or provides asbestos consulting or laboratory services must be certified by the State of Vermont. Personnel who conducted the inspection, bulk sample collections and laboratory analysis were properly certified by the State of Vermont and also possess current EPA approved training in asbestos site inspections and asbestos laboratory analysis. 4. CERTIFICATION/ACCREDITATION Inspection Locations: 1079/1081, 1253 & 1371 Airport Drive, 3 & 4 Delaware Street, 53 North Henry Court and 11 & 49 South Henry Court, South Burlington, Vermont 2

5 KAS, Inc. April 30, 2015 Asbestos Site Inspection Report AIP 88 Inspection Dates: April 1-3, 2015 Buildings Inspected: Eight vacant residential structures. Inspector Certification/Accreditation: The personnel who conducted the inspection/bulk sampling of the facilities hold the following Certification/Accreditation program requirements: Inspector: Amy King: Vermont Asbestos Inspector AI Aaron Roth: Vermont Asbestos Inspector MP Corporate and inspector licenses and certifications are contained in Appendix 1. Asbestos bulk samples have been analyzed by Schneider Laboratories Global, Inc. of Richmond, VA. 5. INSPECTION RESULTS Building material/sample locations and specific results of the sampling and analysis and visual inspection are contained in Table 1 and Appendices 2 and 3. Several asbestos containing materials were identified and are highlighted in Table OBSERVATIONS AND RECOMMENDATIONS Building Comments: All the houses inspected were former recently occupied single family one and two story residences of wood frame construction with asphaltic roofing. The age of the structures are all believed to be over 60 years old. Most had at least partial basements. Most of the locations had at least one shed or detached garage that was also inspected. The buildings were in different states of repair but were mostly in good condition. They had not been empty long enough to evidence significant deterioration. Finishes in the houses varied but none contained asbestos containing thermal system insulation. Recommendations: An EPA/ state notification of the demolition needs to be submitted to both Region 1 EPA and The State of Vermont Asbestos Control program at least 10 working days before any demolition efforts commence. 3

6 KAS, Inc. April 30, 2015 Asbestos Site Inspection Report AIP 88 Prior to demolition the identified asbestos containing materials need to be removed in full compliance with the Vermont Regulations for Asbestos Control. Proper notifications in accordance with US EPA NESHAP 40 CFR Part 61 Subpart M, asbestos, and State of Vermont asbestos requirements in accordance with V.S.A. Title 18, Chapter 26 need to be submitted before any demolition takes place. 4

7 KAS, Inc. April 30, 2015 Asbestos Site Inspection Report AIP 88 TABLE 1 INSPECTION RESULTS SUMMARY 1079/1081, 1253 & 1371 Airport Drive, 3 & 4 Delaware Street, 53 North Henry Court, and 11 & 49 South Henry Court, South Burlington, Vermont HA/SAMPLE # MATERIAL ANALYTICAL QUANTITY/ LOCATION RESULTS CONDITION Airport Drive HA/SAMPLE # MATERIAL ANALYTICAL ACM QTY/ LOCATION RESULTS CONDITION 1/1081-1, 2, 3 Sheet Flooring (Off-White)/Mastic NAD, not ACM Floor 2/1081-4, 5, 6, Sheet Flooring (Mossaic) NAD, not ACM , 27 Throughout 3/1081-7, 8 Peel-n-Stick FT (Gray) NAD, not ACM Rear Entrance 4/1081-9, 10 Countertop Mastic NAD, not ACM 5/ , 12, 13, Blown-In Insulation (over Vermiculite) NAD, not ACM , 39 Attic 6/ , 15, 16, Drywall NAD, not ACM , 35 Throughout 7/ , 18, 19, Joint Compound 2% Chrysotile ~2,000 sqft/nd , 37 Throughout 8/ , 21, 22 Peel-n-Stick FT (Off-White) NAD, not ACM Floor 9/ , 24, 25 Sheeting Flooring (Yellow) NAD, not ACM Floor 10/ , 29, 30 Peel-n-Stick FT (Brown) NAD, not ACM Bathroom 11/ , 32, 33 Sheeting Flooring (Gray) NAD, not ACM Bathroom 12/ , 41 Sink Coating 2% Chrysotile ~6 SF/Good Sink 13/ , 43 Peel-n-Stick FT (Dark Brown) NAD, not ACM Rear Entrance 14/ , 45, 46 Roofing Materials NAD, not ACM Roof 15/ , 48 Flashing Caulk NAD, not ACM Around Chimneys 16/ , 50 Window Glaze NAD, not ACM Basement Windows 17/ , 52 Roofing Materials NAD, not ACM Shed Roof 18/ 1079 and 1081 Vermiculite Assumed ACM >1,600 SF/Good Attic/Wall Cavities 5

8 KAS, Inc. April 30, 2015 Asbestos Site Inspection Report AIP 88 TABLE 1 INSPECTION RESULTS SUMMARY (continued) 1079/1081, 1253 & 1371 Airport Drive, 3 & 4 Delaware Street, 53 North Henry Court, and 11 & 49 South Henry Court, South Burlington, Vermont 1253 Airport Drive 1/1253-1, 2, 3 Peel-n-Stick FT/Mastic, Peel-n-Stick/Mastic NAD, not ACM ~100 sqft/nd Floor Sheet Flooring Sheet Flooring- 20% Chrysotile 2/1253-4, 5, 6 Sheet Flooring (Off-White)/Mastic NAD, not ACM 1 st Floor Bathroom 3/1253-7, 8, 9 Sheet Flooring (Red)/Mastic Sheet Flooring 20% Chrysotile ~100 sqft/d Dining Room Mastic NAD, not ACM 4/ , 11, 12 Peel-n-Stick FT/Mastic NAD, not ACM 2 nd Floor Bathroom 5/ , 14, 15 Drywall NAD, not ACM Portions of 1 st and 2 nd Floor 6/ , 17, 18 Joint Compound NAD, not ACM Portions of 1 st and 2 nd Floor 7/ , 20, 21 Wall Mastic NAD, not ACM Dining Room 8/ , 23, 24 Plaster NAD, not ACM Portions of 1 st Floor and Basement 9/ , 26 Sink Coating 2% Chrysotile ~6 sqft/nd Sink 10/ , 28 Wall Mastic NAD, not ACM 2 nd Floor Bathroom 11/ , 30, X 12 Ceiling Tile (no mastic) NAD, not ACM 2 nd Floor Bathroom 12/ , 33, 34 Window Glaze NAD, not ACM Exterior Windows 13/ , 36, 37 Tar Paper NAD, not ACM Exterior Siding 14/ , 39 Siding Paper NAD, not ACM Back Porch Siding 15/ , 41, 42 Roofing Materials NAD, not ACM Roof 16/ , 44 Flashing Caulk NAD, not ACM Chimney/Roof 17/ , 46 Grey Caulking NAD, not ACM Low Roof and Porch 18/ , 48 Window Glaze 3% Chrysotile ~2 sqft/nd Garage Windows 19/ , 50, 51 Roofing Materials NAD, not ACM Garage Roof and Small Peak 6

9 KAS, Inc. April 30, 2015 Asbestos Site Inspection Report AIP 88 TABLE 1 INSPECTION RESULTS SUMMARY (continued) 1079/1081, 1253 & 1371 Airport Drive, 3 & 4 Delaware Street, 53 North Henry Court, and 11 & 49 South Henry Court, South Burlington, Vermont 1371 Airport Drive 1/1371-1, 2, 3 Floor Tile, Flooring and Mastics NAD, not ACM Floor 2/1371-4, 5, 6 Sheet Flooring/Mastic NAD, not ACM 1 st Floor Bathroom 3/1371-7, 8, 9 Sheet Flooring/Mastic NAD, not ACM 2 nd Floor Bathroom 4/ , 11, 12 Blown-in Insulation NAD, not ACM 2 nd Floor 5/ , 14, 15 Plaster NAD, not ACM 1 st and 2 nd Floor 6/ , 17, 18 Drywall NAD, not ACM 1 st and 2 nd Floor 7/ , 20 Window Glaze NAD, not ACM Basement Windows 8/ , 22 Base Cove/Mastic NAD, not ACM Basement 9/ , 24, 25 Roofing Materials NAD, not ACM Roof 10/ Chimney Flashing Assumed ACM ~ 5 LF chimney 3 Delaware Street 1/3-1, 2, 3 Off-White Sheet Flooring/ Mastic NAD, not ACM Bathroom 2/3-4, 5, 6 Tile/ Mastic NAD, not ACM Bathroom 3/ 3-7, 8, 9 Greenish Vinyl Flooring NAD, not ACM 4/3-10, 11 Gray/ Brown Vinyl Flooring 20% Chrysotile ~5 sqft/nd Storage above basement 5/3-12, 13 Window Glaze NAD, not ACM Basement 6/3-14, 15, 16 Lt Grey 12x12 Tile w/ Mastic 3% Chrysotile ~200 sqft/sd Basement Mastic - NAD, not ACM 7/3-17, 18, 19 Drywall NAD, not ACM Living Room, Bedroom #1 8/3-20, 21, 22 Plaster NAD, not ACM Living Room, bedroom #1 9/3-23, 24, 25 Joint Compound NAD, not ACM Basement open/side room 7

10 KAS, Inc. April 30, 2015 Asbestos Site Inspection Report AIP 88 TABLE 1 INSPECTION RESULTS SUMMARY (continued) 1079/1081, 1253 & 1371 Airport Drive, 3 & 4 Delaware Street, 53 North Henry Court, and 11 & 49 South Henry Court, South Burlington, Vermont 3 Delaware Street (continued) 10/3-26, 27, 28 Drywall NAD, not ACM Basement open room basement side room 11/3-29, 30, 31 Paper NAD, not ACM Siding 12/ 3-32, 33 Flashing 5% Chrysotile ~2 sqft/d Chimney slightly dam. 13/3-34, 35, 36 Dark Grey Shingles NAD, not ACM Roof 14/53-37, 38, 39 Lite Grey Shingles NAD, not ACM Shed 4 Delaware Street 1/4-1, 2, 3 2 layers - Sheet Flooring Top Layer not ACM ~80 sqft/nd Bottom Layer ACM, 15% Chrysotile 2/4-4, 5, 6 Floor Tile / Mastic NAD, not ACM 3/ 4-7, 8, Sheet Flooring NAD, not ACM Bathroom 4/ 4-9, 10 Floor Tile NAD, not ACM Bathroom 5/ 4-11, 12, 13 Carpet Mastic 2% Chrysotile ~200 sqft/nd Living Room, Entry Way To Bed 1, Living Room 6/ 4-14, 15, 16 Plaster NAD, not ACM Bedroom 1, Living Room 7/ 4-17, 18, 19 Drywall NAD, not ACM/ Bedroom 1, Living Room, 8/ 4-20, 21, 22 Dryway NAD, not ACM Dining Area, Sitting Area 9/ 4-23, 24, 25 Joint Compound NAD, not ACM Dining Area, Sitting Area 10/ 4-26, 27 Caulking 15% Chrysotile ~4 linft/d Chimney Fluke 11/ 4-28, 29 Window Glaze 2% Chrysotile ~4 linft/d Basement Windows 12/ 4-30, 31, 32 Blown-In Insulation NAD, not ACM Attic 13/ 4-33, 34, 35 Shingles NAD, not ACM Roof 8

11 KAS, Inc. April 30, 2015 Asbestos Site Inspection Report AIP 88 TABLE 1 INSPECTION RESULTS SUMMARY (continued) 1079/1081, 1253 & 1371 Airport Drive, 3 & 4 Delaware Street, 53 North Henry Court, and 11 & 49 South Henry Court, South Burlington, Vermont 4 Delaware Street (continued) 14/ 4-36, 37 Flashing 5% Chrysotile ~2 sqft/d Chimney 53 North Henry Court 1/ 53-1, 2, 3 Tan Sheet Flooring NAD, not ACM Sun Room 2/ 53-4, 5, 6 Brown/ Tan Sheet Flooring 20% Chrysotile ~250 sqft/nd 3/ 53-7, 8, 9 Tan/ White/ Blue Speckled - NAD, not ACM Bathroom Sheet Flooring 4/ 53-10, 11 Cove Molding/ Mastic NAD, not ACM Bathroom 5/ 53-12, 13 Sink Deadener NAD, not ACM 6/ 53-14, 15, -16 Joint Compound NAD, not ACM, Living Room 7/ 53-17, 18, 19 Textured Ceiling NAD, not ACM 8/ 53-20, 21, 22 Dry Wall NAD, not ACM, Living Room 9/ 53-23, 24, 25 1x1 Ceiling Tiles NAD, not ACM Basement Den 10/ 53-26, 27, 28 Paper under Flooring NAD, not ACM Living Room 11/ 53-29, 30, 31 Wall Mastic - Tan NAD, not ACM Basement Bathroom 12/ 53-32, 33, 34 Mastic On Insulation 3% Chrysotile ~400 sqft/d Basement Outer Walls 13/ 53-35, 36, 37 Shingles/ Tar Paper NAD, not ACM Roof 14/ 53-38, 39 Tar 8% Chrysotile ~2 sqft/d Chimney 15/ 53-40, 41, 42 Paper Siding NAD, not ACM Front Siding 11 South Henry Court 1/ 11-1, 2, 3 Gray Sheet Flooring NAD, not ACM ~100 sqft/d 2/ 11-4, 5 Cove Molding / Mastic NAD, not ACM ~10 lnft/nd 9

12 KAS, Inc. April 30, 2015 Asbestos Site Inspection Report AIP 88 TABLE 1 INSPECTION RESULTS SUMMARY (continued) 1079/1081, 1253 & 1371 Airport Drive, 3 & 4 Delaware Street, 53 North Henry Court, and 11 & 49 South Henry Court, South Burlington, Vermont 11 South Henry Court (continued) 3/ 11-6, 7, 8 Textured Ceiling NAD, not ACM ~100 sqft/d slightly dam. 4/ 11-9, x12 tile/ mastic NAD, not ACM ~20 sq ft/ Bathroom slightly damag. 6/ 11-13, 11-14, x12 White Self Adhesive Tiles NAD, not ACM ~80 sq ft/ Bathroom 12x12 Brown Tiles not damaged 7/ 11-16, 11-17, Maroon Sheet Flooring w/ Mastic NAD, not ACM ~200 sq ft/ Bedroom 1-2 nd Floor, slightly damage. Bed Hallway 2 nd Floor, Bedroom 2 2 nd Floor 8/ 11-19, 11-20, Plaster NAD, not ACM ~ sq ft/ Master Bedroom, Bedroom 1 1 st Floor, Living Room 9/ 11-22, 11-23, Sheetrock NAD, not ACM ~ sq ft/ Master Bedroom, Bedroom 1 1 st Floor, Living Room 10/ 11-25, 11-26, Sheetrock NAD, not ACM ~150 sq feet/ Master Bedroom, Bedroom 1 2nd Floor, 11/ 11-28, 11-29, Joint Compound NAD, not ACM ~20 sq feet/, Master Bedroom Bedroom 1 2 nd Floor 12/ 11-31, 11-32, Black paper under Flooring NAD, not ACM ~100 sq ft/ Living Room not damaged Master Room 13/ 11-34, 11-35, Window Glaze NAD, not ACM ~10 ft/ Basement damaged 14/ 4-37, 4-38 Sink Deadener NAD, not ACM ~2 sq ft/ not damaged 15/ 11-39, 11-40, Tar Paper NAD, not ACM ~500 sq ft/ Outside not damaged 16/ 11/42, 11-43, Shingles/ Tar Paper NAD, not ACM ~ s. ft/ House Roof, Garage Roof 17/ 11-45, Tar 5% Chrysotile ~2 sq ft/ Chimney not damaged 49 South Henry Court 1/49-1, 2 Sink Coating 3% Chrysotile ~2 sq ft/nd 2/49-3, 4, 5 Composite Flooring 25% Chrysotile ~80 sq ft/nd mastic not ACM 3/ 49-6, 7 9x9 floor tile Lite Green NAD, not ACM Bedroom Off 10

13 KAS, Inc. April 30, 2015 Asbestos Site Inspection Report AIP 88 TABLE 1 INSPECTION RESULTS SUMMARY (continued) 1079/1081, 1253 & 1371 Airport Drive, 3 & 4 Delaware Street, 53 North Henry Court, and 11 & 49 South Henry Court, South Burlington, Vermont 49 South Henry Court (continued) 4/49-8, 9 Black Cove Molding/ Mastic NAD, not ACM 5/49-10, 11, 12 Lt Brown Sheet Flooring NAD, not ACM Bathroom 6/49-13, 14, 15 Paper under Flooring NAD, not ACM Living Room 7/49-16, 17, 18 Drywall NAD, not ACM, Room off 8/49-19, 20, 21 Plaster NAD, not ACM, Room off kitchen, bedroom 1 9/49-22, 23, 24 Textured Ceiling NAD, not ACM 10/49-25, 26, 27 Blown In Insulation NAD, not ACM Attic 11/49-28, 29, 30 1x1 Ceiling Tiles NAD, not ACM Finished Room Basement 12/49-31, 32 Flashing coating 5% Chrysotile ~2 ft/d Chimney 13/49-33, 34, 35 Shingles/ Tar Paper NAD, Not ACM House Roof/ Garage Roof 14/49-36, 37, 38 Rolled Roof NAD, Not ACM Porch Roof 8/49-19, 21 Plaster NAD, not ACM, Room off, bedroom 1 9/49-22, 23, 24 Textured Ceiling NAD, not ACM 10/49-25, 26, 27 Blown In Insulation NAD, not ACM Attic 11/49-28, 29, 30 1x1 Ceiling Tiles NAD, Not ACM Finished room basement Notes: 1. HA homogeneous area, flr floor, apt apartment, sqft square feet, lnft linear feet 2. ACM asbestos containing material (greater than 1% asbestos content) 3. Materials equal to or less than 1% asbestos are not considered ACM however when working with the materials VOSHA worker protection procedures must be used. 11

14 KAS, Inc. April 30, 2015 Asbestos Site Inspection Report AIP 88 APPENDIX 1 KAS LICENSES/ CERTIFICATIONS

15

16

17

18 KAS, Inc. April 30, 2015 Asbestos Site Inspection Report AIP 88 APPENDIX 2 LABORATORY ANALYSIS REPORTS

19 Analysis Report Schneider Laboratories Global, Inc 2512 W. Cary Street Richmond, Virginia LABS (5227) Fax Customer: Address: Attn: Project: Location: Number: KAS, Inc. (4771) 368 Ave. D Suite 15 Williston, VT Burlington Airport Buyout 1079 & 1081 Airport Dr Order #: Received 04/08/15 Analyzed 04/08/15 Reported 04/14/15 PO Number: Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Layer 1: Sheet Flooring White, Organically Bound Layer 2: Glue Beige, Soft /03/ Layer 1: Sheet Flooring White, Organically Bound Layer 2: Glue Beige, Soft /03/ Layer 1: Sheet Flooring White, Organically Bound Layer 2: Glue Beige, Soft /03/ Living Room Layer 1: Sheet Flooring Tan/Green, Org.Bound/Fibrous 40% 60% /03/ Living Room Layer 1: Sheet Flooring Tan/Green, Org.Bound/Fibrous 45% 55% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 1 of 9

20 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Layer 1: Sheet Flooring Tan/Green, Org.Bound/Fibrous Bedroom 2 35% 65% /03/ Back Entrance Layer 1: Floor Tile 2% Gray, Organically Bound 98% Layer 2: Glue Clear, Soft /03/ Back Entrance Layer 1: Floor Tile/Mastic Gray/Green, Org.Bound/Fibrous/Soft 15% 85% /03/ Layer 1: Counter Top 10% White/Brown, Hard 90% Layer 2: Mastic 2% Brown, Soft 98% /03/ Layer 1: Counter Top 12% White/Brown, Hard 88% Layer 2: Mastic 3% Brown, Soft 97% /03/ Attic Space Layer 1: Insulation 98% Gray, Fibrous 2% /03/ Attic Space Layer 1: Insulation 95% Gray, Fibrous 5% /03/ Attic Space Layer 1: Insulation 96% Gray, Fibrous 4% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 2 of 9

21 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Layer 1: Drywall 20% White, Powdery 80% Layer 2: Joint Compound White, Granular /03/ Living Room Layer 1: Drywall 15% White, Powdery No Joint Compound Found. 85% /03/ Bedroom 2 Layer 1: Drywall 12% White, Powdery 88% Layer 2: Joint Compound White, Granular /03/ Layer 1: Joint Compound Tan, Granular 2% CHRYSOTILE 98% Layer 1: 04/03/ Joint Compound Living Room Not analyzed due to positive stop instructions /03/ Bedroom 2 Layer 1: Joint Compound Not analyzed due to positive stop instructions /03/ Layer 1: Floor Tile Off White, Organically Bound Layer 2: Glue 3% Yellow, Soft 97% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 3 of 9

22 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Layer 1: Floor Tile Off White, Organically Bound Layer 2: Glue 2% Beige, Soft 98% /03/ Layer 1: Floor Tile Off White, Organically Bound Layer 2: Glue 2% Beige, Soft 98% /03/ Layer 1: Sheet Flooring Yellow, Org.Bound/Fibrous 40% 60% Layer 2: Glue Yellow, Brittle /03/ Layer 1: Sheet Flooring Yellow, Org.Bound/Fibrous 45% 55% Layer 2: Glue Yellow, Brittle /03/ Layer 1: Sheet Flooring Yellow, Org.Bound/Fibrous 35% 65% Layer 2: Glue Yellow, Brittle Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 4 of 9

23 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Layer 1: Sheet Flooring Tan/Green, Org.Bound/Fibrous Living Room 55% 45% Layer 2: Glue 2% Brown, Brittle 98% /03/ Living Room Layer 1: Sheet Flooring Tan/Green, Org.Bound/Fibrous 30% 70% Layer 2: Glue 3% Brown, Brittle 97% /03/ Bathroom Layer 1: Sheet Flooring Brown/Gray, Organically Bound Layer 2: Glue 2% Clear, Soft 98% /03/ Bathroom Layer 1: Sheet Flooring Brown/Gray, Organically Bound Layer 2: Glue 5% Clear, Soft 95% /03/ Bathroom Layer 1: Sheet Flooring Brown/Gray, Organically Bound Layer 2: Glue 3% Clear, Soft 97% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 5 of 9

24 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Layer 1: Sheet Flooring Gray, Org.Bound/Fibrous Bathroom 40% 60% Layer 2: Glue Beige, Soft /03/ Bathroom Layer 1: Sheet Flooring Gray, Org.Bound/Fibrous 45% 55% Layer 2: Glue Beige, Soft /03/ Bathroom Layer 1: Sheet Flooring Gray, Org.Bound/Fibrous 30% 70% Layer 2: Glue Beige, Soft /03/ Living Room Layer 1: Drywall 20% White, Powdery 80% /03/ Bedroom 2 Layer 1: Drywall 12% White, Powdery 88% /03/ Living Room Layer 1: Drywall 20% White, Powdery 80% Layer 2: Joint Compound Tan, Granular 2% CHRYSOTILE 98% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 6 of 9

25 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Bedroom 2 Layer 1: Drywall 10% White, Powdery 90% Layer 2: Joint Compound Not analyzed due to positive stop instructions /03/ Attic Space Layer 1: Insulation 98% Gray, Fibrous 2% /03/ Attic Space Layer 1: Insulation 95% Gray, Fibrous 5% /03/ Layer 1: Coating Black, Bituminous 2% CHRYSOTILE 98% Layer 1: 04/03/ Coating Not analyzed due to positive stop instructions /03/ Back Entrance Layer 1: Flooring Blue/Beige, Organically Bound Layer 2: Glue Clear, Soft /03/ Back Entrance Layer 1: Flooring Blue/Beige, Organically Bound Layer 2: Glue Clear, Soft Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 7 of 9

26 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Layer 1: Roofing Material Black, Bituminous/Granular Roof 1079/1081 Airport Dr 20% 80% MINERAL/GLASS WOOL Layer 2: Roofing Material 40% Black, Bituminous/Fibrous 60% /03/ Roof 1079/1081 Airport Dr Layer 1: Roofing Material Black, Bituminous/Granular 18% 82% MINERAL/GLASS WOOL Layer 2: Roofing Material 35% Black, Bituminous/Fibrous 65% /03/ Roof 1079/1081 Airport Dr Layer 1: Roofing Material Black, Bituminous/Granular 15% 85% MINERAL/GLASS WOOL Layer 2: Roofing Material 40% Black, Bituminous/Fibrous 60% /03/ Flashing Caulk Chimney Layer 1: Caulk White, Soft /03/ Flashing Caulk Chimney Layer 1: Caulk White, Soft /03/ Basement Window Layer 1: Window Glaze White, Brittle /03/ Basement Window Layer 1: Window Glaze White, Brittle Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 8 of 9

27 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Layer 1: Roofing Material Black, Bituminous/Granular Garage Roof 10% 90% MINERAL/GLASS WOOL /03/ Garage Roof Layer 1: Roofing Material Black, Bituminous/Granular 12% 88% MINERAL/GLASS WOOL Analyst: Eldanaf, Hind /14/15 09:16 AM Reviewed By: Elsamani Abdelfadiel Analyst Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 9 of 9

28

29

30

31

32

33

34 Analysis Report Schneider Laboratories Global, Inc 2512 W. Cary Street Richmond, Virginia LABS (5227) Fax Customer: Address: Attn: Project: Location: Number: KAS, Inc. (4771) 368 Ave. D Suite 15 Williston, VT Burlington Airport Buyout 1253 Airport Dr Order #: Received 04/08/15 Analyzed 04/10/15 Reported 04/14/15 PO Number: Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Layer 1: Sheet Flooring White, Organically Bound Layer 2: Glue Clear, Soft Layer 3: Sheet Flooring White/Beige, Org.Bound/Fibrous 20% CHRYSOTILE 35% 45% /03/ Layer 1: Sheet Flooring White, Organically Bound Layer 2: Glue Clear, Soft Layer 3: Sheet Flooring Not analyzed due to positive stop instructions /03/ Layer 1: Sheet Flooring White, Organically Bound Layer 2: Glue Clear, Soft Layer 3: Sheet Flooring Not analyzed due to positive stop instructions. Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 1 of 8

35 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Layer 1: Sheet Flooring Off White, Org.Bound/Fibrous Bathroom 1 Fl 30% 10% 60% MINERAL/GLASS WOOL Layer 2: Glue Yellow, Brittle /03/ Layer 1: Sheet Flooring Off White, Org.Bound/Fibrous Bathroom 1 Fl 40% 5% 55% MINERAL/GLASS WOOL Layer 2: Glue Yellow, Brittle /03/ Layer 1: Sheet Flooring Off White, Org.Bound/Fibrous Bathroom 1 Fl 30% 5% 65% MINERAL/GLASS WOOL Layer 2: Glue Yellow, Brittle /03/ Dining Room Layer 1: Sheet Flooring Red/Beige, Org.Bound/Fibrous 20% CHRYSOTILE 20% 60% Layer 2: Glue Yellow, Brittle Layer 1: 04/03/ Sheet Flooring Dining Room Not analyzed due to positive stop instructions. Layer 2: Glue Yellow, Brittle Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 2 of 8

36 Method: Sample ID Layer 1: EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Dining Room Sheet Flooring Not analyzed due to positive stop instructions. Layer 2: Glue Yellow, Brittle /03/ Bathroom 2 Fl Layer 1: Tile Black, Organically Bound Layer 2: Glue Clear, Soft /03/ Bathroom 2 Fl Layer 1: Tile Black, Organically Bound Layer 2: Glue Clear, Soft /03/ Bathroom 2 Fl Layer 1: Tile Black, Organically Bound Layer 2: Glue Clear, Soft /03/ Bedroom 2 Closet Layer 1: Drywall 10% White, Powdery 90% /03/ Dining Room Layer 1: Drywall 20% White, Powdery 80% /03/ Bathroom Layer 1: Drywall 12% White, Powdery 88% /03/ Bedroom 2 Closet Layer 1: Joint Compound White, Granular Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 3 of 8

37 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Dining Room Layer 1: Joint Compound White, Granular /03/ Bathroom Layer 1: Joint Compound White, Granular /03/ Dining Room Layer 1: Mastic 2% Yellow, Soft 98% /03/ Dining Room Layer 1: Mastic 4% Yellow, Soft 96% /03/ Dining Room Layer 1: Mastic 3% Yellow, Soft 97% /03/ Dining Room Layer 1: Plaster 2% Gray, Granular 98% /03/ Basement Stairwell Layer 1: Plaster 2% Gray, Granular 98% /03/ Basement Stairwell Layer 1: Plaster 2% Gray, Granular 98% /03/ Sink Layer 1: Coating Beige, Granular 2% CHRYSOTILE 98% Layer 1: 04/03/ Coating Sink Not analyzed due to positive stop instructions. Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 4 of 8

38 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Bathroom 2 Fl Layer 1: Mastic 2% Brown, Brittle 98% /03/ Bathroom 2 Fl Layer 1: Mastic 4% Brown, Brittle 96% /03/ Living Room Layer 1: Ceiling Tile 98% White/Brown, Fibrous 2% /03/ Bedroom 1 Layer 1: Ceiling Tile 95% White/Brown, Fibrous 5% /03/ Dining Room Layer 1: Ceiling Tile 96% White/Brown, Fibrous 4% /03/ Exterior Windows Layer 1: Window Glaze White, Brittle /03/ Exterior Windows Layer 1: Window Glaze White, Brittle /03/ Exterior Windows Layer 1: Window Glaze White, Brittle /03/ Exterior Siding Layer 1: Tar Paper 45% Black, Bituminous/Fibrous 55% /03/ Exterior Siding Layer 1: Tar Paper 40% Black, Bituminous/Fibrous 60% /03/ Exterior Siding Layer 1: Tar Paper 35% Black, Bituminous/Fibrous 65% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 5 of 8

39 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Exterior Porch Layer 1: Paper 98% Pink, Fibrous 2% /03/ Exterior Porch Layer 1: Paper 95% Pink, Fibrous 5% /03/ Roof Layer 1: Roofing Material Black/White, Bituminous/Granular 20% 80% Layer 2: Roofing Material 35% Black, Bituminous/Fibrous 65% Layer 3: Roofing Material Black, Bituminous/Fibrous 12% 88% MINERAL/GLASS WOOL /03/ Roof Layer 1: Roofing Material Black, Bituminous/Granular 10% 90% Layer 2: Roofing Material 40% Black, Bituminous/Fibrous 60% Layer 3: Roofing Material Black, Bituminous/Fibrous 20% 80% MINERAL/GLASS WOOL /03/ Roof Layer 1: Roofing Material Black/White, Bituminous/Granular 12% 88% Layer 2: Roofing Material 30% Black, Bituminous/Fibrous Only Two Layers Of Roofing Found. 70% /03/ Chimney Layer 1: Flashing 10% Black, Bituminous 90% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 6 of 8

40 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Chimney Layer 1: Flashing 8% Black, Bituminous 92% /03/ Low Roof Flashing Layer 1: Caulk Gray, Brittle /03/ Around Back Flue Layer 1: Caulk Gray, Brittle /03/ Garage Windows Layer 1: Window Glaze Beige, Soft Layer 2: Bituminous Material Black/Silver, Bituminous/Brittle 3% CHRYSOTILE 2% 95% Unable to separate individual layers /03/ Garage Windows Layer 1: Window Glaze Beige, Soft Layer 2: Bituminous Material Not analyzed due to positive stop instructions. Unable to separate individual layers /03/ Small Peaks Roof House Layer 1: Roofing Material Black/White/Green, Bituminous/Granular 20% 80% Layer 2: Tar Paper 40% Black, Bituminous/Fibrous 60% /03/ Garage Roof Layer 1: Roofing Material Black/White/Green, Bituminous/Granular 18% 82% Layer 2: Tar Paper 25% Black, Bituminous/Fibrous 75% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 7 of 8

41 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Layer 1: Roofing Material Black/Gray, Bituminous/Granular Garage Roof 12% 88% Layer 2: Tar Paper 35% Black, Bituminous/Fibrous 65% Analyst: Eldanaf, Hind /14/15 09:58 AM Reviewed By: Elsamani Abdelfadiel Analyst Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 8 of 8

42

43

44

45

46

47

48 Analysis Report Schneider Laboratories Global, Inc 2512 W. Cary Street Richmond, Virginia LABS (5227) Fax Customer: Address: Attn: Project: Location: Number: KAS, Inc. (4771) 368 Ave. D Suite 15 Williston, VT Burlington Airport Buyout 1371 Airport Drive Order #: Received 04/08/15 Analyzed 04/09/15 Reported 04/14/15 PO Number: Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Layer 1: Floor Tile Red, Organically Bound Layer 2: Mastic Tan, Soft Layer 3: Backing Black, Bituminous/Fibrous 65% 15% 20% MINERAL/GLASS WOOL Layer 4: Mastic Brown, Brittle /03/ Layer 1: Floor Tile Red, Organically Bound Layer 2: Mastic Tan, Soft Layer 3: Backing Black, Bituminous/Fibrous 65% 15% 20% MINERAL/GLASS WOOL Layer 4: Mastic Brown, Brittle Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 1 of 5

49 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Layer 1: Floor Tile Red, Organically Bound Layer 2: Mastic Tan, Soft Layer 3: Backing Black, Bituminous/Fibrous 65% 15% 20% MINERAL/GLASS WOOL Layer 4: Mastic Brown, Brittle /03/ Layer 1: Sheet Flooring Beige, Org.Bound/Fibrous 1 Fl Bath 35% 15% 50% MINERAL/GLASS WOOL Layer 2: Mastic Tan, Soft /03/ Layer 1: Sheet Flooring Beige, Org.Bound/Fibrous 1 Fl Bath 35% 15% 50% MINERAL/GLASS WOOL Layer 2: Mastic Tan, Soft /03/ Layer 1: Sheet Flooring Beige, Org.Bound/Fibrous 1 Fl Bath 35% 15% 50% MINERAL/GLASS WOOL Layer 2: Mastic Tan, Soft Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 2 of 5

50 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Layer 1: Sheet Flooring Beige, Org.Bound/Fibrous 2 Fl Bath 35% 15% 50% MINERAL/GLASS WOOL Layer 2: Mastic Tan, Soft /03/ Layer 1: Sheet Flooring Beige, Org.Bound/Fibrous 2 Fl Bath 35% 15% 50% MINERAL/GLASS WOOL Layer 2: Mastic Tan, Soft /03/ Layer 1: Sheet Flooring Beige, Org.Bound/Fibrous 2 Fl Bath 35% 15% 50% MINERAL/GLASS WOOL Layer 2: Mastic Tan, Soft /03/ Crawl Space 2 Fl Layer 1: Insulation 90% MINERAL/GLASS WOOL Beige, Fibrous 10% /03/ Crawl Space 2 Fl Layer 1: Insulation 90% MINERAL/GLASS WOOL Beige, Fibrous 10% /03/ Crawl Space 2 Fl Layer 1: Insulation 90% MINERAL/GLASS WOOL Beige, Fibrous 10% /03/ Fl Bedroom Layer 1: Plaster Gray, Granular Layer 2: Skim Coat White, Granular Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 3 of 5

51 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Living Room Layer 1: Plaster Gray, Granular Layer 2: Skim Coat White, Granular /03/ Bedroom 1 Fl Layer 1: Plaster Gray, Granular Layer 2: Skim Coat White, Granular /03/ Fl Bedroom Layer 1: Drywall 4% White, Powdery 96% /03/ Living Room Layer 1: Drywall 4% White, Powdery 96% /03/ Bedroom 1 Fl Layer 1: Drywall 4% White, Powdery 96% /03/ Basement Layer 1: Window Glaze White, Granular /03/ Basement Layer 1: Window Glaze Beige, Granular /03/ Basement Layer 1: Cove Base Gray/Beige, Rubbery Layer 2: Mastic Tan, Soft Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 4 of 5

52 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/03/ Basement Layer 1: Cove Base Gray/Beige, Rubbery Layer 2: Mastic Tan, Soft /03/ Layer 1: Roofing Material Black/Red, Bituminous/Granular Roof 5% 5% 90% MINERAL/GLASS WOOL Layer 2: Felt 65% Black, Fibrous 15% MINERAL/GLASS WOOL 20% Layer 3: Roofing Material Black/Red, Bituminous/Granular /03/ Roof Layer 1: Roofing Material Black/Red, Bituminous/Granular 5% 5% 90% 5% 5% 90% MINERAL/GLASS WOOL MINERAL/GLASS WOOL Layer 2: Felt 65% Black, Fibrous 15% MINERAL/GLASS WOOL 20% Layer 3: Roofing Material Black/Red, Bituminous/Granular /03/ Roof Layer 1: Roofing Material Black/Beige, Bituminous/Granular 5% 5% 90% 5% 5% 90% MINERAL/GLASS WOOL MINERAL/GLASS WOOL Layer 2: Felt 65% Black, Fibrous 15% MINERAL/GLASS WOOL 20% Analyst: Abdelfadiel, Elsamani /14/15 11:13 AM Reviewed By: Hind Eldanaf Microscopy Supervisor Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 5 of 5

53

54

55

56

57 Analysis Report Schneider Laboratories Global, Inc 2512 W. Cary Street Richmond, Virginia LABS (5227) Fax Customer: Address: Attn: Project: Location: Number: KAS, Inc. (4771) 368 Ave. D Suite 15 Williston, VT Burlington Airport Buyout 3 Delaware Street Order #: Received 04/09/15 Analyzed 04/11/15 Reported 04/11/15 PO Number: Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/02/ Bathroom Layer 1: Sheet Flooring White, Rubbery Layer 2: Mastic Yellow, Soft /02/ Bathroom Layer 1: Sheet Flooring White, Rubbery Layer 2: Mastic Yellow, Soft /02/ Bathroom Layer 1: Sheet Flooring White, Rubbery Layer 2: Mastic Yellow, Soft /02/ Bathroom Layer 1: Tile White, Hard Layer 2: Mastic Yellow, Soft /02/ Bathroom Layer 1: Tile White, Hard Layer 2: Mastic Yellow, Soft Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 1 of 5

58 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/02/ Bathroom Layer 1: Tile White, Hard Layer 2: Mastic Yellow, Soft /02/ Layer 1: Vinyl Flooring 15% MINERAL/GLASS WOOL Light Green, Rubbery 85% Layer 2: Mastic Yellow, Soft /02/ Layer 1: Vinyl Flooring 15% MINERAL/GLASS WOOL Light Green, Rubbery 85% Layer 2: Mastic Yellow, Soft /02/ Layer 1: Vinyl Flooring 15% MINERAL/GLASS WOOL Light Green, Rubbery 85% Layer 2: Mastic Yellow, Soft /02/ Storage Basement Stairs Layer 1: Vinyl Flooring Gray/Brown, Org.Bound/Fibrous 20% CHRYSOTILE 25% 55% Sample was inhomogenous, subsamples of each component were analyzed separately /02/ Storage Basement Stairs Layer 1: Vinyl Flooring Not analyzed due to positive stop instructions /02/ Basement Windows Layer 1: Window Glaze Gray, Granular /02/ Basement Windows Layer 1: Window Glaze Gray, Granular /02/ Basemnt Layer 1: Tile Light Gray, Organically Bound 3% CHRYSOTILE 97% Layer 2: Mastic Black, Bituminous Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 2 of 5

59 Method: Sample ID Layer 1: EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/02/ Basemnt Tile Not analyzed due to positive stop instructions. Layer 2: Mastic Black, Bituminous Layer 1: 04/02/ Tile Basemnt Not analyzed due to positive stop instructions. Layer 2: Mastic Black, Bituminous /02/ Living Room Layer 1: Drywall 4% White, Powdery 96% /02/ Living Room Layer 1: Drywall 4% White, Powdery 96% /02/ Bedroom 1 Layer 1: Drywall 4% White, Powdery 96% /02/ Living Room Layer 1: Plaster Gray, Granular Layer 2: Skim Coat White, Granular /02/ Living Room Layer 1: Plaster Gray, Granular Layer 2: Skim Coat White, Granular /02/ Bedroom 1 Layer 1: Plaster Gray, Granular Layer 2: Skim Coat White, Granular /02/ Basement Open Room Layer 1: Joint Compound White, Granular Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 3 of 5

60 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/02/ Basement Open Room Layer 1: Joint Compound White, Granular /02/ Basement Side Room Layer 1: Joint Compound White, Granular /02/ Basement Open Room Layer 1: Drywall 4% White, Powdery 96% /02/ Basement Open Room Layer 1: Drywall 4% White, Powdery 96% /02/ Basement Side Room Layer 1: Drywall 4% White, Powdery 96% /02/ Siding Layer 1: Paper 65% Silver, Fibrous 35% /02/ Siding Layer 1: Paper 65% Silver, Fibrous 35% /02/ Siding Layer 1: Paper 65% Silver, Fibrous 35% /02/ Chimney Layer 1: Flashing Gray/Black, Bituminous 5% CHRYSOTILE 95% Layer 1: 04/02/ Flashing Chimney Not analyzed due to positive stop instructions /02/ Roof Layer 1: Shingle Dark Gray, Granular/Bituminous 20% MINERAL/GLASS WOOL Sample was inhomogenous, subsamples of each component were analyzed separately. Layer 2: Felt Paper 55% Black, Bituminous/Fibrous 10% 35% SYNTHETIC FIBER Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 4 of 5

61 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/02/ Layer 1: Shingle Dark Gray, Granular/Bituminous Roof Sample was inhomogenous, subsamples of each component were analyzed separately. 20% 80% MINERAL/GLASS WOOL Layer 2: Felt Paper 55% Black, Bituminous/Fibrous 10% 35% SYNTHETIC FIBER /02/ Layer 1: Shingle Dark Gray, Granular/Bituminous Roof Sample was inhomogenous, subsamples of each component were analyzed separately. 20% 80% MINERAL/GLASS WOOL Layer 2: Felt Paper 55% Black, Bituminous/Fibrous 10% 35% SYNTHETIC FIBER /02/ Layer 1: Shingle Light Gray, Granular/Bituminous Shed Roof Sample was inhomogenous, subsamples of each component were analyzed separately /02/ Shed Roof Layer 1: Shingle Gray/Brown, Granular/Bituminous 15% 70% 15% 20% 80% SYNTHETIC FIBER MINERAL/GLASS WOOL Sample was inhomogenous, subsamples of each component were analyzed separately /02/ Shed Roof Layer 1: Shingle Light Gray, Granular/Bituminous Sample was inhomogenous, subsamples of each component were analyzed separately. 15% 70% 15% SYNTHETIC FIBER Analyst: Abdelfadiel, Elsamani /11/15 02:54 PM Reviewed By: Hind Eldanaf Microscopy Supervisor Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 5 of 5

62

63

64

65

66

67 Analysis Report Schneider Laboratories Global, Inc 2512 W. Cary Street Richmond, Virginia LABS (5227) Fax Customer: Address: Attn: Project: Location: Number: KAS, Inc. (4771) 368 Ave. D Suite 15 Williston, VT Burlington Airport Buyout 4 Delaware Street Order #: Received 04/09/15 Analyzed 04/10/15 Reported 04/14/15 PO Number: Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/02/ Layer 1: Sheet Flooring Beige, Org.Bound/Fibrous 40% 60% Layer 2: Sheet Flooring Yellow/Blue, Org.Bound/Fibrous 15% CHRYSOTILE 30% 55% /02/ Layer 1: Sheet Flooring Beige, Org.Bound/Fibrous 40% 60% Layer 2: Sheet Flooring Not analyzed due to positive stop instructions /02/ Layer 1: Sheet Flooring Beige, Org.Bound/Fibrous 40% 60% Layer 2: Sheet Flooring Not analyzed due to positive stop instructions. Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 1 of 6

68 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/02/ Layer 1: Floor Tile Beige, Organically Bound Layer 2: Mastic 3% Black, Soft 97% /02/ Layer 1: Floor Tile Beige, Organically Bound Layer 2: Mastic 2% Black, Soft 98% /02/ Layer 1: Floor Tile Beige, Organically Bound Layer 2: Mastic 3% Black, Soft 97% /02/ Bathroom Layer 1: Sheet Flooring Off White, Organically Bound Layer 2: Sheet Flooring 90% Light Gray, Fibrous 10% /02/ Bathroom Layer 1: Sheet Flooring Off White, Organically Bound Layer 2: Sheet Flooring 90% Light Gray, Fibrous 10% /02/ Bathroom Layer 1: Floor Tile Gray, Organically Bound Layer 2: Mastic 2% Yellow, Soft 98% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 2 of 6

69 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/02/ Bathroom Layer 1: Floor Tile Gray, Organically Bound Layer 2: Mastic 2% Yellow, Soft 98% /02/ Living Room Layer 1: Carpet Mastic Brown, Brittle 2% CHRYSOTILE 3% 95% Layer 1: 04/02/ Carpet Mastic Entry Way To Bed 1 Not analyzed due to positive stop instructions /02/ Living Room Layer 1: Carpet Mastic Not analyzed due to positive stop instructions /02/ Bedroom 1 Layer 1: Plaster 97% Gray, Granular 3% SYNTHETIC FIBER Layer 2: Skim Coat White, Granular /02/ Living Room Layer 1: Plaster 98% Gray, Granular 2% SYNTHETIC FIBER Layer 2: Skim Coat White, Granular /02/ Layer 1: Plaster 97% Gray, Granular 3% SYNTHETIC FIBER Layer 2: Skim Coat White, Granular Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 3 of 6

70 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/02/ Bedroom 1 Layer 1: Drywall 4% White, Powdery 96% /02/ Living Room Layer 1: Drywall 4% White, Powdery 96% /02/ Layer 1: Drywall 5% White, Powdery 95% /02/ Dining Area Layer 1: Drywall 4% White, Powdery 96% /02/ Dining Area Layer 1: Drywall 5% White, Powdery 95% /02/ Sitting Area Layer 1: Drywall 4% White, Powdery 96% /02/ Dining Area Layer 1: Joint Compound White, Granular /02/ Dining Area Layer 1: Joint Compound White, Granular /02/ Sittin garea Layer 1: Joint Compound White, Granular /02/ Chimney Flue Layer 1: Caulking White, Powdery/Fibrous 15% CHRYSOTILE 35% 50% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 4 of 6

71 Method: Sample ID Layer 1: EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/02/ Chimney Flue Caulking Not analyzed due to positive stop instructions /02/ Basement Windows Layer 1: Window Glaze Beige, Soft 2% CHRYSOTILE 98% Layer 1: 04/02/ Window Glaze Basement Windows Not analyzed due to positive stop instructions /02/ Attic Layer 1: Insulation 80% Gray, Fibrous 20% /02/ Attic Layer 1: Insulation 80% Gray, Fibrous 20% /02/ Attic Layer 1: Insulation 85% Gray, Fibrous 15% /02/ Roof Layer 1: Shingle Black/Gray, Bituminous/Granular 15% 85% MINERAL/GLASS WOOL /02/ Roof Layer 1: Shingle Black/Gray, Bituminous/Granular 15% 85% MINERAL/GLASS WOOL /02/ Roof Layer 1: Shingle Black/Gray, Bituminous/Granular 15% 85% MINERAL/GLASS WOOL /02/ Chimney Layer 1: Flashing Black, Bituminous 5% CHRYSOTILE 95% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 5 of 6

72 Method: Sample ID Layer 1: EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/02/ Chimney Flashing Not analyzed due to positive stop instructions. Analyst: Eldanaf, Hind /14/15 08:13 AM Reviewed By: Elsamani Abdelfadiel Analyst Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 6 of 6

73

74

75

76

77

78 Analysis Report Schneider Laboratories Global, Inc 2512 W. Cary Street Richmond, Virginia LABS (5227) Fax Customer: Address: Attn: Project: Location: Number: KAS, Inc. (4771) 368 Ave. D Suite 15 Williston, VT Burlington Airport Buyout 53 North Henry Court Order #: Received 04/09/15 Analyzed 04/13/15 Reported 04/14/15 PO Number: Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Sun Room Layer 1: Sheet Flooring Tan, Organically Bound Layer 2: Mastic Tan, Soft /01/ Sun Room Layer 1: Sheet Flooring Tan, Organically Bound Layer 2: Mastic Tan, Soft /01/ Sun Room Layer 1: Sheet Flooring Tan, Organically Bound Layer 2: Mastic Tan, Soft /01/ Layer 1: Sheet Flooring Brown/Tan, Org.Bound/Fibrous 20% CHRYSOTILE 20% 60% Layer 2: Mastic Tan, Soft Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 1 of 7

79 Method: Sample ID Layer 1: EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Sheet Flooring Not analyzed due to positive stop instructions. Layer 2: Mastic Tan, Soft Layer 1: 04/01/ Sheet Flooring Not analyzed due to positive stop instructions. Layer 2: Mastic Tan, Soft /01/ Bathroom Layer 1: Sheet Flooring White/Tan, Organically Bound Layer 2: Mastic Tan, Soft /01/ Bathroom Layer 1: Sheet Flooring Tan/White, Organically Bound Layer 2: Mastic Tan, Soft /01/ Bathroom Layer 1: Sheet Flooring Tan/White, Organically Bound Layer 2: Mastic Tan, Soft /01/ Bathroom Layer 1: Cove Base White, Rubbery Layer 2: Mastic Tan, Soft Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 2 of 7

80 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Bathroom Layer 1: Cove Base White, Rubbery Layer 2: Mastic Tan, Soft /01/ Sink Layer 1: Bituminous Material 2% Black, Bituminous 98% /01/ Sink Layer 1: Bituminous Material 2% Black, Bituminous 98% /01/ Layer 1: Joint Compound White, Granular /01/ Layer 1: Joint Compound White, Granular /01/ Living Room Layer 1: Joint Compound White, Granular /01/ Layer 1: Textured Ceiling White, Granular /01/ Layer 1: Textured Ceiling White, Granular /01/ Layer 1: Textured Ceiling White, Granular /01/ Layer 1: Drywall 15% White, Powdery 85% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 3 of 7

81 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Layer 1: Drywall 15% White, Powdery 85% /01/ Living Room Layer 1: Drywall 15% White, Powdery 85% /01/ Basement Den Layer 1: Ceiling Tile 40% Beige, Fibrous 40% MINERAL/GLASS WOOL 20% /01/ Basement Den Layer 1: Ceiling Tile 40% Beige, Fibrous 40% MINERAL/GLASS WOOL 20% /01/ Basement Den Layer 1: Ceiling Tile 40% Beige, Fibrous 40% MINERAL/GLASS WOOL 20% /01/ Living Room Layer 1: Paper 80% Brown, Fibrous 20% /01/ Living Room Layer 1: Paper 80% Brown, Fibrous 20% /01/ Living Room Layer 1: Paper 80% Brown, Fibrous 20% /01/ Basement Bathroom Layer 1: Mastic Tan, Soft Layer 2: Fibrous Material 65% Brown, Fibrous 15% MINERAL/GLASS WOOL 20% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 4 of 7

82 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Basement Bathroom Layer 1: Mastic Tan, Soft Layer 2: Fibrous Material 65% Brown, Fibrous 15% MINERAL/GLASS WOOL 20% /01/ Basement Bathroom Layer 1: Mastic Tan, Soft Layer 2: Fibrous Material 65% Brown, Fibrous 15% MINERAL/GLASS WOOL 20% /01/ Layer 1: Mastic Black, Bituminous Basement Out Walls 3% CHRYSOTILE 97% Layer 2: Spongy Material White, Spongy Layer 1: 04/01/ Mastic Basement Out Walls Not analyzed due to positive stop instructions. Layer 2: Spongy Material White, Spongy Layer 1: 04/01/ Mastic Basement Out Walls Not analyzed due to positive stop instructions. Layer 2: Spongy Material White, Spongy Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 5 of 7

83 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Layer 1: Shingle Black/Green, Bituminous/Granular Living Room Area Roof 20% 80% MINERAL/GLASS WOOL Layer 2: Mastic 2% Black, Bituminous 98% Layer 3: Tar Paper 65% Black, Fibrous/Bituminous 15% MINERAL/GLASS WOOL 20% /01/ Layer 1: Shingle Black/Green, Bituminous/Granular Living Room Area Roof 20% 80% MINERAL/GLASS WOOL Layer 2: Mastic 2% Black, Bituminous 98% Layer 3: Tar Paper 65% Black, Fibrous/Bituminous 15% MINERAL/GLASS WOOL 20% /01/ Roof Area Layer 1: Shingle 20% MINERAL/GLASS WOOL Black/Green, Granular/Bituminous 80% Layer 2: Mastic 2% Black, Bituminous 98% Layer 3: Tar Paper 65% Black, Fibrous/Bituminous 15% MINERAL/GLASS WOOL 20% /01/ Layer 1: Tar Black, Bituminous Chimney 8% CHRYSOTILE 92% Layer 1: 04/01/ Tar Chimney Not analyzed due to positive stop instructions /01/ Front Siding Layer 1: Paper 80% Black/Silver, Fibrous 20% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 6 of 7

84 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Front Siding Layer 1: Paper 80% Black/Silver, Fibrous 20% /01/ Front Siding Layer 1: Paper 80% Black/Silver, Fibrous 20% Analyst: Abdelfadiel, Elsamani /14/15 01:17 PM Reviewed By: Hind Eldanaf Microscopy Supervisor Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 7 of 7

85

86

87

88

89

90

91 Analysis Report Schneider Laboratories Global, Inc 2512 W. Cary Street Richmond, Virginia LABS (5227) Fax Customer: Address: Attn: Project: Location: Number: KAS, Inc. (4771) 368 Ave. D Suite 15 Williston, VT Burlington Airport Buyout 11 South Henry Court Order #: Received 04/09/15 Analyzed 04/13/15 Reported 04/14/15 PO Number: Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Layer 1: Sheet Flooring Gray, Org.Bound/Fibrous 40% 60% Layer 2: Backing 95% Brown, Fibrous 5% /01/ Layer 1: Sheet Flooring Gray, Org.Bound/Fibrous 40% 60% Layer 2: Backing 95% Brown, Fibrous 5% /01/ Layer 1: Sheet Flooring Gray, Org.Bound/Fibrous 40% 60% Layer 2: Mastic 5% Yellow, Soft 95% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. The test results reported relate only to the samples submitted. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 1 of 8

92 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Layer 1: Cove Base Black, Rubbery Layer 2: Mastic 5% Brown, Soft 95% Layer 3: Backing 95% Brown, Fibrous 5% /01/ Layer 1: Cove Base Black, Rubbery Layer 2: Mastic 5% Brown, Soft 95% Layer 3: Backing 95% Brown, Fibrous 5% /01/ Layer 1: Textured Ceiling 5% White, Granular 95% /01/ Layer 1: Textured Ceiling 5% White, Granular 95% /01/ Layer 1: Textured Ceiling 5% White, Granular 95% /01/ Master Bath Layer 1: Tile Tan, Organically Bound Layer 2: Mastic 5% Yellow, Soft 95% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. The test results reported relate only to the samples submitted. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 2 of 8

93 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Master Bath Layer 1: Tile Tan, Organically Bound Layer 2: Mastic 5% Yellow, Soft 95% /01/ Bathroom Layer 1: Mastic 5% Yellow, Brittle 95% /01/ Bathroom Layer 1: Tile White, Brittle Layer 2: Mastic Yellow/White, Soft/Fibrous 35% 65% Unable to separate individual layers /01/ Bathroom Layer 1: Tile White, Organically Bound Layer 2: Mastic 2% Clear, Soft 98% Layer 3: Tile Brown, Organically Bound Layer 4: Mastic 3% Brown, Brittle 97% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. The test results reported relate only to the samples submitted. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 3 of 8

94 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Bathroom Layer 1: Tile White, Organically Bound Layer 2: Mastic 2% Clear, Soft 98% Layer 3: Tile Brown, Organically Bound Layer 4: Mastic 3% Brown, Brittle 97% /01/ Bathroom Layer 1: Tile White, Organically Bound Layer 2: Mastic 2% Clear, Soft 98% Layer 3: Tile Brown, Organically Bound Layer 4: Mastic 3% Brown, Brittle 97% /01/ Bed 1 2 Fl Layer 1: Sheet Flooring Maroon, Organically Bound Layer 2: Mastic/Fibrous Mtrl Black, Fibrous/Bituminous 60% 40% Unable to separate individual layers /01/ Bed Hall 2 Fl Layer 1: Sheet Flooring Maroon, Organically Bound Layer 2: Mastic/Fibrous Mtrl Black, Fibrous/Bituminous 60% 40% Unable to separate individual layers. Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. The test results reported relate only to the samples submitted. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 4 of 8

95 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Bed 2 2 Fl Layer 1: Sheet Flooring Maroon, Organically Bound Layer 2: Mastic/Fibrous Mtrl Black, Fibrous/Bituminous 60% 40% Unable to separate individual layers /01/ Master Bedroom Layer 1: Skim Coat White, Granular Layer 2: Plaster Gray, Granular Layer 3: Drywall 20% White, Powdery 80% /01/ Bedroom 1 Fl Layer 1: Skim Coat White, Granular Layer 2: Plaster Gray, Granular /01/ Living Room Layer 1: Skim Coat White, Granular/Fibrous 30% 70% Layer 2: Plaster Gray, Granular /01/ Master Bedroom Layer 1: Sheetrock 20% White, Powdery 80% /01/ Bedroom 1 Fl Layer 1: Sheetrock 20% White, Powdery 80% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. The test results reported relate only to the samples submitted. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 5 of 8

96 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Living Room Layer 1: Sheetrock 20% White, Powdery 80% /01/ Master Bedroom Layer 1: Sheetrock 20% White, Powdery 80% /01/ Bedroom 1 2 Fl Layer 1: Sheetrock 20% White, Powdery 80% /01/ Layer 1: Sheetrock 20% White, Powdery 80% /01/ Layer 1: JC/Particle Board White/Brown, Granular/Fibrous 45% 55% /01/ Master Bedroom Layer 1: JC/Particle Board White/Brown, Granular/Fibrous 45% 55% /01/ Bedroom 1 2 Fl Layer 1: JC/Particle Board White/Brown, Granular/Fibrous 45% 55% /01/ Living Room Layer 1: Paper 55% Black, Fibrous/Bituminous 45% /01/ Master Bedroom Layer 1: Paper 55% Black, Fibrous/Bituminous 45% /01/ Master Bedroom Layer 1: Paper 55% Black, Fibrous/Bituminous 45% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. The test results reported relate only to the samples submitted. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 6 of 8

97 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Basement Window Layer 1: Window Glaze 2% Gray, Granular 98% /01/ Basement Window Layer 1: Window Glaze 2% Gray, Granular 98% /01/ Basement Window Layer 1: Window Glaze 2% Gray, Granular 98% /01/ Layer 1: Coating 15% Gray, Granular 85% /01/ Layer 1: Coating 15% Gray, Granular 85% /01/ Outside Layer 1: Tar Paper 60% Black, Fibrous/Bituminous 40% /01/ Outside Layer 1: Tar Paper 60% Black, Fibrous/Bituminous 40% /01/ Outside Layer 1: Tar Paper 60% Black, Fibrous/Bituminous 40% /01/ House Roof Layer 1: Shingle Black/Gray, Bituminous/Granular 20% 80% Layer 2: Tar Paper 60% Black, Fibrous/Bituminous 40% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. The test results reported relate only to the samples submitted. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 7 of 8

98 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Layer 1: Shingle Black/Gray, Bituminous/Granular Garage Roof 20% 80% Layer 2: Tar Paper 60% Black, Fibrous/Bituminous 40% /01/ Garage Roof Layer 1: Shingle Black/Gray, Bituminous/Granular 20% 80% Layer 2: Tar Paper 60% Black, Fibrous/Bituminous 40% /01/ Chimney Center Roof Layer 1: Tar Black, Bituminous 5% CHRYSOTILE 95% Layer 1: 04/01/ Tar Chimney Center Roof Not analyzed due to positive stop instructions. Analyst: Abdelfadiel, Elsamani /14/15 02:44 PM Reviewed By: Hind Eldanaf Microscopy Supervisor Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. The test results reported relate only to the samples submitted. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 8 of 8

99

100

101

102

103 Analysis Report Schneider Laboratories Global, Inc 2512 W. Cary Street Richmond, Virginia LABS (5227) Fax Customer: Address: Attn: Project: Location: Number: KAS, Inc. (4771) 368 Ave. D Suite 15 Williston, VT Burlington Airport Buyout 49 South Henry Court Order #: Received 04/09/15 Analyzed 04/09/15 Reported 04/14/15 PO Number: Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Layer 1: Coating Black, Bituminous 3% CHRYSOTILE 97% Layer 1: 04/01/ Coating Not analyzed due to positive stop instructions /01/ Layer 1: Flooring Gray, Organically Bound Layer 2: Backing Gray, Fibrous 25% CHRYSOTILE 30% 45% Layer 3: Mastic 5% Yellow, Soft 95% /01/ Layer 1: Flooring Gray, Organically Bound Layer 2: Backing Not analyzed due to positive stop instructions. Layer 3: Mastic 5% Yellow, Soft 95% Layer 4: Backing 95% Brown, Fibrous 5% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 1 of 6

104 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Layer 1: Flooring Gray, Organically Bound Layer 2: Backing Not analyzed due to positive stop instructions. Layer 3: Mastic 5% Yellow, Soft 95% /01/ Bedroom Off Layer 1: Tile Gray, Organically Bound Layer 2: Mastic 5% Brown, Brittle 95% /01/ Bedroom Off Layer 1: Tile 5% Gray, Organically Bound 95% Layer 2: Mastic 5% Brown, Brittle 95% /01/ Layer 1: Cove Base Black, Rubbery Layer 2: Mastic 5% Brown, Soft 95% /01/ Layer 1: Cove Base Black, Rubbery Layer 2: Mastic 5% Brown, Soft 95% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 2 of 6

105 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Bathroom Layer 1: Flooring Brown, Organically Bound Layer 2: Backing 60% Gray, Fibrous 20% MINERAL/GLASS WOOL 20% Layer 3: Backing 95% Brown, Fibrous 5% /01/ Bathroom Layer 1: Flooring Brown, Organically Bound Layer 2: Backing 60% Gray, Fibrous 20% MINERAL/GLASS WOOL 20% Layer 3: Backing 95% Brown, Fibrous 5% /01/ Bathroom Layer 1: Flooring Brown, Organically Bound Layer 2: Backing 60% Gray, Fibrous 20% MINERAL/GLASS WOOL 20% Layer 3: Backing 95% Brown, Fibrous 5% /01/ Living Room Layer 1: Paper 95% Brown, Fibrous 5% /01/ Living Room Layer 1: Paper 95% Brown, Fibrous 5% /01/ Living Room Layer 1: Paper 95% Brown, Fibrous 5% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 3 of 6

106 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Layer 1: Drywall 10% White, Powdery 90% /01/ Room Off Layer 1: Drywall 10% White, Powdery 90% Layer 2: Drywall 20% Gray, Powdery 80% /01/ Room Off Layer 1: Drywall 10% White, Powdery 90% /01/ Layer 1: Skim Coat White, Granular Layer 2: Plaster 95% Gray, Granular 5% SYNTHETIC FIBER /01/ Roof Off Layer 1: Skim Coat White, Granular Layer 2: Plaster 95% Gray, Granular 5% SYNTHETIC FIBER /01/ Bedroom 1 Layer 1: Skim Coat White, Granular Layer 2: Plaster 95% Gray, Granular 5% SYNTHETIC FIBER /01/ Layer 1: Textured Ceiling 2% White, Granular 98% /01/ Layer 1: Textured Ceiling 2% White, Granular 98% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 4 of 6

107 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Layer 1: Textured Ceiling 2% White, Granular 98% /01/ Bedroom 1 Acess Layer 1: Insulation 80% Brown, Fibrous 15% MINERAL/GLASS WOOL 5% /01/ Bedroom 1 Acess Layer 1: Insulation 80% Brown, Fibrous 15% MINERAL/GLASS WOOL 5% /01/ Bedroom 1 Acess Layer 1: Insulation 80% Brown, Fibrous 15% MINERAL/GLASS WOOL 5% /01/ Finished Room Basement Layer 1: Ceiling Tile 85% White, Fibrous 15% /01/ Finished Room Basement Layer 1: Ceiling Tile 85% White, Fibrous 15% /01/ Finished Room Basement Layer 1: Ceiling Tile 85% White, Fibrous 15% /01/ Chimney Layer 1: Flashing Black, Bituminous 5% CHRYSOTILE 95% Layer 1: 04/01/ Flashing Chimney Not analyzed due to positive stop instructions /01/ House Roof Front Layer 1: Shingle Black/Gray, Bituminous/Granular 20% 80% MINERAL/GLASS WOOL Layer 2: Tar Paper 60% Black, Fibrous/Bituminous 40% Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 5 of 6

108 Method: Sample ID EPA 600/R-93/116 & 600/M PLM Analysis Collected Cust. ID Location Asbestos Fibers Other Materials 04/01/ Layer 1: Shingle Black/Gray, Bituminous/Granular Garage Roof 20% 80% MINERAL/GLASS WOOL Layer 2: Tar Paper 60% Black, Fibrous/Bituminous 40% /01/ House Roof Back Layer 1: Shingle Black/Gray, Bituminous/Granular 20% 80% MINERAL/GLASS WOOL Layer 2: Tar Paper 60% Black, Fibrous/Bituminous 40% /01/ Layer 1: Roofing Material Black/White, Bituminous/Granular Porch Roof /01/ Porch Roof Layer 1: Roofing Material Black/White, Bituminous/Granular /01/ Porch Roof Layer 1: Roofing Material Black/White, Bituminous/Granular Analyst: Abdelfadiel, Elsamani /14/15 01:24 PM 10% 10% 80% 10% 10% 80% 10% 10% 80% MINERAL/GLASS WOOL MINERAL/GLASS WOOL MINERAL/GLASS WOOL Reviewed By: Hind Eldanaf Microscopy Supervisor Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory. Accrediting bodies: AIHA-LAP, LLC , NVLAP , NYELAP 11413, VELAP/NELAC Page 6 of 6

109