SHURLOC 150 STANDARD DETAILS
|
|
- Emerald Heath
- 5 years ago
- Views:
Transcription
1 OVER WOOD DECK STANDARD DETAILS Austin - Headquarters/Sales Office 830 Sagebrush Drive Austin, TX (512) (800) Fax (512) info@ctmrs.com Seguin - Plant/Sales Office 720 West IH 10 Seguin, TX (830) (877) Fax (830)
2 ARCHITECT / ENGINEERING DATA 18" MAX 1 1/2" 1" GENERAL DESCRIPTION Rib height : 1 1/2 Coverage widths: Inquire Integral batten. Standard striations (optional without). Minimum slope: 3:12 Panel attachment: Clip (concealed fastener). Panel Substrate: Galvalume or Galvanized. Gauges: 26, 24, or 22 Coatings: Acrylic Coated Galvalume Paint Grip Silicone Modified Polyester Paint System Kynar 500 Paint System Other substrates and finishes available, please inquire. Use a properly aligned and uniform substructure to avoid panel distortion. Typical substructures include plywood and OSB. All substructure must be properly engineered to meet specified design loads. For illustration purposes, details are shown over plywood decking. Any mechanical attachment device that does not lay flat on the deck will telegraph through the panels. Panels can be used on roofs with transitions or slope changes. All panels are subject to surface distortion due to improperly applied fasteners. Overdriven fasteners will cause stress and induce oil canning across the face of the panel at or near the point of attachment. Standard CTMRS fasteners are recommended for attachment to metal and wood for all architectural panels. Use maximum caution when fastening to a wood structure. All panels require sealant at eave or valley conditions. Narrower widths, heavier gauges, striations, and embossing minimize the chance of oil canning. Fastener spacing affects the final appearance of the roof. Oil canning is not a reason for field rejection. SH150 3
3 RIDGE/HIP TYPICAL DETAILS 4" O.C. OR PANEL SEALANT RIDGE FLASHING "Z" CLOSURE 6" O.C. 2 PER FLOATING RIDGE 4" O.C. OR SEALANT RIDGE FLASH PANEL "Z" CLOSURE FASTENER # 14 (POP RIVET) 4" O.C. 2 PER 2"X2"X16GA. ANGLE SH150 4
4 VALLEY TYPICAL DETAILS VALLEY WITH OFFSET 12" MAX 4 1 2" MIN. FOR STD. VALLEY 9" MIN. FOR EXT VALLEY PANEL VALLEY TRIM 2 PER 12" O.C. OFFSET FILL END WITH SEALANT 12" O.C. VALLEY WITH INTEGRATED 12" MAX 4 1 2" MIN. FOR STD. VALLEY 9" MIN. FOR EXT VALLEY VALLEY TRIM PANEL 2 PER FILL END WITH SEALANT SH150 5
5 FIXED RAKE TYPICAL DETAILS FINISHING ON MODULE BOX RAKE 6" O.C. OR PANEL ZEE CLOSURE CONTINUOUS FINISHING OFF MODULE BOX RAKE 6" O.C. OR FIELD TURN PANEL UP 1 1 2" PANEL ZEE CLOSURE CONTINUOUS SH150 6
6 FLOATING RAKE TYPICAL DETAILS FINISHING ON MODULE BOX RAKE RAKE SUPPORT PARAPET RAKE 6" O.C. OR (DO NOT RESTRICT MOVEMENT OF RAKE SUPPORT) CONTINUOUS FINISHING OFF MODULE PARAPET RAKE 6" O.C. OR BOX RAKE RAKE SUPPORT FIELD TURN PANEL UP 1 1/2" (DO NOT RESTRICT MOVEMENT OF RAKE SUPPORT) CONTINUOUS SH150 7
7 ALTERNATE RAKE TYPICAL DETAILS FIELD CUT AND FOLD PANEL CONTINUOUS 2 PER SH150 8
8 EAVE TYPICAL DETAILS PANEL CONTINUOUS SH150 9
9 GUTTER TYPICAL DETAILS PANEL FASTENER # 14 (POP RIVET) TAPE SEALER GUTTER STRAP FASTENER # 14 (POP RIVET) 2 PER 12" O.C. GUTTER SH150 10
10 FIXED SIDEWALL TYPICAL DETAILS FINISHING ON MODULE SIDING SIDEWALL PARAPET RAKE FLASHING 6" O.C. OR FASTENER # 4 ( 1 4 "-14 X 7 8 " LAP) OR #7 ( 1 4 "-14 X 7 8 " LONG LIFE) 6" O.C. FINISHING OFF MODULE SIDING SIDEWALL PARAPET RAKE FLASHING 6" O.C. OR FASTENER # 4 ( 1 4 "-14 X 7 8 " LAP) OR #7 ( 1 4 "-14 X 7 8 " LONG LIFE) FIELD TURN PANEL UP 1 1/2" 6" O.C. SH150 11
11 FLOATING SIDEWALL TYPICAL DETAILS FINISHING ON MODULE SIDING SIDEWALL / PARAPET RAKE FLASHING FLOATING RAKE SUPPORT (DO NOT RESTRICT MOVEMENT OF RAKE SUPPORT) FINISHING OFF MODULE SIDING SIDEWALL / PARAPET RAKE FLASHING FLOATING RAKE SUPPORT (DO NOT RESTRICT MOVEMENT OF RAKE SUPPORT) SH150 12
12 PEAK TYPICAL DETAILS 4" O.C. OR Z CLOSURE W/ URETHANE SEALANT PEAK FLASHING 6" O.C. CONTINUOUS SH150 13
13 ENDWALL TYPICAL DETAILS SIDING END WALL / HIGH SIDE EAVE FLASHING 4" O.C. OR FASTENER # 4 ( 1 4 "-14 X 7 8 " LAP) OR #7 ( 1 4 "-14 X 7 8 " LONG LIFE) "Z" CLOSURE W/ SEALANT 6" O.C. COUNTER FLASHING ALTERNATE COUNTER FLASHING CAULK COUNTER FLASHING END WALL / HIGH SIDE EAVE FLASHING FASTENER # 13 (DRIVE PIN) ALTERNATE COUNTER FLASHING END WALL / HIGH SIDE SH150 14
14 FLOATING ENDWALL TYPICAL DETAILS SIDING END WALL / HIGH SIDE EAVE FLASHING 4" O.C. OR FASTENER # 4 ( 1 4 "-14 X 7 8 " LAP) OR #7 ( 1 4 "-14 X 7 8 " LONG LIFE) "Z" CLOSURE W/ SEALANT 2x2 16 GA ANGLE FASTENER #14 (POP RIVET) 6" O.C. COUNTER FLASHING ALTERNATE COUNTER FLASHING CAULK CAULK COUNTER FLASHING END WALL / HIGH SIDE EAVE FLASHING FASTENER # 13 (DRIVE PIN) ALTERNATE COUNTER FLASHING END WALL / HIGH SIDE EAVE FLASHING SH150 15
* Other widths available upon request. 24 Gauge Galvalume - Standard Surface. Other gauges and aluminium available upon request.
is a concealed fastener architectural standing seam roof panel. The panels are easily installed over decking, utilizing metal clips. panels are ideally suited for decorative mansard, fascia and roofs.
More informationIMPORTANT NOTICE READ THIS MANUAL COMPLETELY PRIOR TO BEGINNING THE INSTALLATION OF THE WEATHER GUARD PANEL.
IMPORTANT NOTICE READ THIS MANUAL COMPLETELY PRIOR TO BEGINNING THE INSTALLATION OF THE WEATHER GUARD PANEL. IF THERE IS A CONFLICT BETWEEN PROJECT ERECTION DRAWINGS PROVIDED OR APPROVED BY WHIRLWIND BUILDING
More informationTRIAD CORRUGATED METAL, INC.
TRIAD CORRUGATED METAL, INC. C O M M E R C I A L R E S I D E N T I A L A G R I C U L T U R A L Snap Loc Panel Guide Snap Loc metal panels are a perfect fit for residential, architectural and commercial
More informationTRIAD CORRUGATED METAL, INC.
TRIAD CORRUGATED METAL, INC. COMMERCIAL RESIDENTIAL AGRICULTURAL MS-216 MS-218 Panel Guide This guide describes the design and performance characteristics of the MS-216 and MS-218 Roof panel system. The
More information5V Crimp DESIGN/INSTALLATION INFORMATION
5V Crimp DESIGN/INSTALLATION INFORMATION IMPORTANT NOTICE READ THIS MANUAL COMPLETELY PRIOR TO BEGINNING THE INSTALLATION OF THE SYSTEM. METAL DEPOTS DETAILS MUST BE FOLLOWED AS A MINIMUM TO INSURE APPROPRIATE
More informationCentral Texas Metal Roofing Supply Co., Inc 36" SHEET WIDTH 38 ¼ 40 ¼ 38 ¼ 40 ¼ 38 ¼ 40 ¼ 40 ¼ 40 ¼ NET COVERAGE
3 4 " 9" 36" GAUGE PANEL FINISH 26 26 26 26 24 24 24 24 FRONTIER RIB LAP GUARD FRONTIER RIB LAP GUARD FRONTIER RIB LAP GUARD LAP GUARD LAP GUARD GALVALUME GALVALUME SMP SMP GALVALUME GALVALUME KYNAR500
More informationTable of Contents. 3. Standing Seam Panels
Table of Contents 895 North Parkway 3. Standing Seam Panels Standing Seam Panels Table of Contents... PS1-2 Double-Lok... PS3-8 Ultra-Dek... PS9-14 BattenLok HS... PS15-18 Curved BattenLok HS... PS19-20
More informationCentral Texas Metal Roofing Supply Co., Inc NET COVERAGE SHEET WIDTH
1 2 " 1 24" GAUGE PANEL FINISH NET COVERAGE SHEET WIDTH WEIGHT PER SQ. 26 5 Vee GALVALUME 24 26 3/8 95.00 PRICE PER SQ. PRICE PER LINEAR FOOT PANEL PRICING: 1. Price per Square is based on 26 3/8 sheet
More informationCentral Texas Metal Roofing Supply Co., Inc 36" NET COVERAGE SHEET WIDTH 38 ¼ 40 ¼ 38 ¼ 40 ¼ 38 ¼ 40 ¼ 40 ¼ 40 ¼
36" 1 2 " 6" GAUGE PANEL FINISH NET COVERAGE SHEET WIDTH WEIGHT PER SQ. 26 26 26 26 24 24 24 24 TEXAS RIB CHANNEL GUARD TEXAS RIB CHANNEL GUARD TEXAS RIB CHANNEL GUARD CHANNEL GUARD CHANNEL GUARD GALVALUME
More informationCentral Texas Metal Roofing Supply Co., Inc SHEET WIDTH 38 ¼ 40 ¼ 38 ¼ 40 ¼ 38 ¼ 40 ¼ 38 ¼ 40 ¼ 38 ¼ 40 ¼
GAUGE PANEL FINISH NET COVERAGE 26 26 26 26 U PBU U PBU GALVALUME GALVALUME SMP SMP (NOTE 1) SHEET WIDTH 38 ¼ 40 ¼ 38 ¼ 40 ¼ WEIGHT PER SQ. 95.00 95.00 95.00 95.00 24 24 24 24 24 24 U PBU U PBU U PBU GALVALUME
More informationEVERSEAM 20 APPLICATION GUIDE
EVERSEAM 20 APPLICATION GUIDE Panel Overview Our Name Says It All!"#$%#&'()*+,!"#$%#&'(-.( Applications: The EverSeam panel is an architectural panel that is ideal for residential and light commercial
More informationResidential Pricing Guide
Guide TABLE OF CONTENTS Panels 5V Crimp Slimline 2 4 Accessories Flat Sheets Coils V-Groove Soffit Ridge Caps Roof Jacks Touch-up Paint Insulation Slimline Rib Cover Closure Strips Tube Sealant 6 6 7
More information1.5 mechanical lock ml 150
1.5 mechanical lock ml 150 Strip Width Base Material Thickness Min Tensible Min Yield Coatings Max 16 Steel.0225 to.0336 in 52 - ksi 50 - ski Painted / Galvalume UL CONSTRUCTION NUMBERS: TGKX554 The Mechanical
More information2120 SW Poma Drive; Palm City, Florida Phone Fax
2120 SW Poma Drive; Palm City, Florida 34990 772-223-4055 Phone 772-781-7492 Fax www.sunlastmetal.com sales@sunlastmetal.com IMPORTANT NOTICE READ THIS MANUAL COMPLETELY BEFORE BEGINNING INSTALLATION OF
More information1.5 mechanical lock ml 150
1.5 mechanical lock ml 150 Strip Width Base Material Thickness Min Tensible Min Yield Coatings Max 16 Steel.0225 to.0336 in 52 - ksi 50 - ski Painted / Galvalume UL CONSTRUCTION NUMBERS: TGKX554 The Mechanical
More informationTABLE OF CONTENTS PRODUCT CATALOGUE fax OVERVIEW PBR 7.2 LONGSPAN ECONORIB
PRODUCT CATALOGUE www.metroll.us sales@fontana.metroll.com ph. 909.823.7663 fax 909.693.5153 TABLE OF CONTENTS OVERVIEW PBR Product Overview and Color Charts Panel Information and Trim 7.2 LONGSPAN ECONORIB
More informationTable of Contents. Notes to Designer/User Map of Typical Roof Conditions...3 Fastener Placement...4 Fastener Selection...5
Table of Contents Section Page Notes to Designer/User...................1-2 Map of Typical Roof Conditions..............3 Fastener Placement........................4 Fastener Selection.........................5
More informationTable of Contents. 3. Exposed Fastener Panels
Table of Contents 895 North Parkway 3. Exposed Fastener Panels Exposed Fastener Panels Table of Contents... PE1-2 PBR... PE3-4 PBA... PE5-6 AVP... PE7-8 PBU... PE9-10 PBC... PE11-12 PBD... PE13-14 7.2...
More informationSTILE. Panel Information. Design/Installation Considerations. Flashing Profiles. Detail Conditions. Notes. Accessory Profiles. Testing Information
Table of ontents Product Page No. Product Page No. Panel Information Profile...PST-2 Panel Overview...PST-2 Flashing Profiles Eave...PST- Extended Eave...PST- leat...pst- Stile Starter...PST- Box Gutter...PST-
More informationTYPICAL ROOF CONDITION LAYOUT
FIXED POINTS TYPICAL ROOF CONDITION LAYOUT 15 17 9 16 29 12 14 11 3 7 35 20 6 23 30 31 24 13 18 Typical Roof Condition Layout... 1 Low Eave Isometric View - Fixed/ Floating... 2 Low Eave Section - Fixed/
More informationIMAGE II. Panel Information. Detail Conditions. Flashing Profiles. Accessory Profiles. Testing Information. Design/Installation Considerations PIM-1
Table of ontents Product Page No. Product Page No. Panel Information Profiles... PIM-2 Panel Overview...PIM-2 Flashing Profiles Eave...PIM-3 Extended Eave...PIM-3 leat...pim-3 Offset leat...pim-3 5K Gutter...PIM-3
More information900 SERIES PANEL SHEET INDEX ENDLAP INSTALLATION SEQUENCE L.E. W/ GUTTER VAPOR BARRIER CS-RK-01B-900
CS-PJ-01-900 CS-DS-01-900 CS-PJ-02-900 CS-EL-01-900 CS-EL-02-900 CS-EL-03-900 CS-EL-04-900 CS-RD-01-900 CS-RD-02-900 CS-RD-03-900 CS-EV-01A-900 CS-EV-01B-900 CS-EV-02A-900 CS-EV-02B-900 CS-EV-03A-900 CS-EV-03B-900
More informationCentral Snap. Condition Details C SNAPDETAILS
Central Snap Condition Details D C SNAPDETAILS150612.2 The men and women at Central States Manufacturing, Inc. would like to welcome you. OUR MISSION Central States Manufacturing, Inc. is a 100% employee-owned
More information2120 SW Poma Drive; Palm City, Florida Phone Fax
2120 SW Poma Drive; Palm City, Florida 34990 772-223-4055 Phone 772-781-7492 Fax www.sunlastmetal.com sales@sunlastmetal.com IMPORTANT NOTICE READ THIS MANUAL COMPLETELY BEFORE BEGINNING INSTALLATION OF
More informationPrior to ordering and installing materials, all dimensions should be verified by field measurements.
Important Information The application and detail drawings in this manual are strictly for illustration purposes and may not be applicable to all building designs or product installations. All projects
More informationw w w. s a q u l i t y m e ta l s. c o m
san antonio branch 210 W. Peden San Antonio TX 78204 P. (210) 227-7276 F. (210) 227-0329 MCALLEN branch 2221 Austin Ave McAllen TX 78501 P. (956) 627-2966 F. (956) 627-0918 w w w. s a q u l i t y m e ta
More informationSL-16. Design/Installation Information
SL-16 Design/Installation Information IMPORTANT NOTICE READ THIS MANUAL COMPLETELY PRIOR TO BEGINNING THE INSTALLATION OF THE SL Series ROOFING SYSTEM. ALWAYS INSPECT EACH AND EVERY PANEL AND ALL ACCESSORIES
More informationPBR & PBU PANELS. Technical/Installation Information
PBR & PBU PANELS Technical/Installation Information IMPORTANT NOTICE READ THIS MANUAL COMPLETELY PRIOR TO BEGINNING THE INSTALLATION OF THE PANEL S. THE MANUFACTURER DETAILS MUST BE FOLLOWED AS A MINIMUM
More information1.5 snap lock sl 150
1.5 snap lock sl 150 Strip Width Base Material Thickness Min Tensible Min Yield Coatings 12.00 to 24 Steel.0128 to.027 in 52 - ksi 50 - ski Painted / Galvalume UL CONSTRUCTION NUMBERS: TGKX301, tgkx342a,
More informationMAXIMA. Maxima Testing Data, Section Properties, and Load Tables
MAXIMA Maxima Maxima Testing Data, Section Properties, and Load Tables For any available Testing Data, Section Properties, or Load Tables, please visit www.mcelroymetal.com. For additional information,
More informationCONTOUR CORRUGATED PANEL
CONTOUR CORRUGATED PANEL Table of Contents SECTION PAGE Designer Notes............................................... 1 Panel Net Coverage / Fasteners.................................... 2 ROOF Details
More informationWESTERN RIB. Installation, Flashings & Shop Drawing Detail Guide.
WESTERN RIB Installation, Flashings & Shop Drawing Detail Guide 901 W. Watkins Street Phoenix, AZ 85007 Phone: (877) 787-5467 (855) 426-7836 Email: sales@cortenroofing.com sales@metalforroofing.com For
More informationNUCOR VR 16 II STANDING SEAM ROOF SYSTEM TABLE OF CONTENTS
NUCOR VR 16 II STANDING SEAM ROOF SYSTEM TABLE OF CONTENTS Nucor VR16 II Vertical Rib Standing Seam Roof System...2 Nucor VR16 II Property and Span Tables...3 Standard Details...5 ED3010PE - Gutter...5
More information238T and 138T Panel and Accessories Price List 9/29/2017 (price good for shipments through 11/31/2017) Customer Job Date Sales Rep 238T PANEL ITEM #
238T and 138T Panel and Accessories Price List 9/29/2017 (price good for shipments through 11/31/2017) Customer Job Date Sales Rep 238T PANEL ITEM # DESCRIPTION SELLING PRICE UOM 238T 238T Seam Cap 24
More informationTrusted Tested Tough Kalaeloa Blvd, Kapolei, Hawaii Phone (808) Fax (808) Neighbor Islands (800)
MAC 200 STRUCTURAL STANDING SEAM METAL ROOF SYSTEM Trusted Tested Tough 91-104 Kalaeloa Blvd, Kapolei, Hawaii 96707 Phone (808) 682-3000 Fax (808) 682-3636 Neighbor Islands (800) 352-3920 www.kloecknermetals.com
More informationFor Metal Roofing Systems Fascia, Mansards,& Soffits
HIGGINS STEEL ROOFING SERIES 2000 STANDING SEAM DETAIL MANUAL For Metal Roofing Systems Fascia, Mansards,& Soffits Wall Panels/Siding HIGGINS CONSTRUCTION & SUPPLY CO. 3801 U. S. 50 HILLSBORO, OHIO 45133
More informationWestern States 7/8 Corrugated
Western States 7/8 Corrugated Installation, Flashings & Shop Drawing Detail Guide Table of Contents Section Page Section Page Notes to Designer / Installers..1 Fastener Placement and Selection.2-3 Key
More informationSECTION METAL ROOF AND SOFFIT PANELS
Metal Panel Systems, Inc. 11506 Reading Road Cincinnati, Ohio 45241-2512 Telephone: 800-554-6126 or 513-554-6120 Fax: 513-554-6121 www.metalpanelsystems.com info@metalpanelsystems.com Specifications for
More informationPBR & PBU PANELS. Technical/Installation Information
PBR & PBU PANELS Technical/Installation Information IMPORTANT NOTICE READ THIS MANUAL COMPLETELY PRIOR TO BEGINNING THE INSTALLATION OF THE Retro-R PANELS. THE MANUFACTURER DETAILS MUST BE FOLLOWED AS
More informationPROLOK EAVE PROLOK ROOFING PANEL ROOFING NAIL
EAVE ROOFING NOTE: ROOF PITCH IS REQUIRED FOR FABRICATION LOW SLOPE ADD SEALER TAPE ROOFING NAIL 2x4 SUB- 2x8 EAVE TRIM 1. Install the eave trim using roofing nails. 2. If sealer tape is being used, install
More information5V CRIMP. Technical/Installation Information
5V CRIMP Technical/Installation Information IMPORTANT NOTICE READ THIS MANUAL OCMPLETELY PRIOR TO BEGINNING THE INSTALLATION OF THE SYSTEM. ALWAYS INSPECT EACH AND EVERY PANEL AND ALL ACCESSORIES BEFORE
More informationRESIDENTIAL LIGHT GAUGE APPLICATION GUIDE
Our Name Says It All RESIDENTIAL LIGHT GAUGE APPLICATION GUIDE Lebanon, PA 888.339.0059 Bridgton, ME 800.677.2060 Howe, IN 866.562.3782 www.everlastroofing.com Residential Light Gauge Table of Contents
More informationR PANEL / PBR PANEL. Installation, Flashings & Shop Drawing Detail Guide.
R PANEL / PBR PANEL Installation, Flashings & Shop Drawing Detail Guide 901 W. Watkins Street Phoenix, AZ 85007 Phone: (877) 787-5467 (855) 426-7836 Email: sales@cortenroofing.com sales@metalforroofing.com
More informationS BI COM P ON E NT CA T ALOG
SBI METAL BUILDINGS & COMPONENTS S BI COM P ON E NT CA T ALOG Date: 03 / 16 / 2017 COMMERCIAL PRODUCTS Commercial Panels and Trim Cee, Zee, Eave Struts, Angle, Channel, and Clips Accessories FT 0 1 2 3
More informationINSTALLATION INSTRUCTIONS for MP-RC1 TWO PIECE CONSTRUCTION TO BE INSTALLED ON COMPLETED ROOF DECK
INSTALLATION INSTRUCTIONS for MP-RC1 TWO PIECE CONSTRUCTION TO BE INSTALLED ON COMPLETED ROOF DECK A. 1. Using curb ribs as a guide, layout and mark roof openings on completed roof deck as outside curb
More informationRoofing Installation Manual: Concealed Fastener Panels Material Data, Trim Details, and Step-by-Step Instructions
Roofing Installation Manual: Concealed Fastener Panels Material Data, Trim Details, and Step-by-Step Instructions 1974 Livengood Ave Fairbanks, AK 99701 907-479-6002 allsteel.info@gmail.com Roof Installation
More informationLokSeam. Design/Installation Information. This booklet includes: Trims and Accessories Design and Installation Information
LokSeam Design/Installation Information This booklet includes: Trims and Accessories Design and Installation Information IMPORTANT NOTICE READ THIS MANUAL COMPLETELY PRIOR TO BEGINNING THE INSTALLATION
More informationCONTINUOUS VENTILATORS
CONTINUOUS VENTILATORS used on metal roofing systems roofs conform to high standards and specifications which have been developed, tested and proven over many years. They provide an excellent value for
More informationSIDEWALL/ENDWALL STANDING SEAM TRIMS SIDEWALL/ENDWALL CROSS SECTION NTS SIDING OR OTHER WALL CLADDING, TYP LOW PROFILE FASTENER, TYP
CHIMNEY FLASHING CROSS SECTION 1. CHIMNEY FLASHING TRIM IS DESIGNED TO FLASH AROUND CHIMNEYS AND LARGE PENETRATIONS (E.G. SKYLIGHTS). CH1 AND CH7 ARE INTENDED FOR USE WITH MOST EXPOSED FASTENER AND STANDING
More informationCONSTRUCTION DETAILS HANDBOOK
100 AMBOY AVENUE PERTH AMBOY, NJ 08861 TEL 73-86-8614 FAX 73-86-8865 www.englertinc.com CONSTRUCTION DETAILS HANDBOOK For METAL ROOFING SYSTEMS FASCIA, MANSARDS, & SOFFITS WALL PANELS/SIDING INTRODUCTION
More informationCLIP-LOC. Panel Information. Detail Conditions. Flashing Profiles. Notes. Accessory Profiles. Testing Information. Design/Installation Considerations
LIP-LO Table of ontents Product Page No. Product Page No. Panel Information lip-loc Panel Profile... PL-2 Panel Overview... PL-2 Flashing Profiles Eave... PL- leat... PL- Box Gutter... PL- Box Gutter End...
More informationSuperior Structural Standing Seam Roof Systems
07 61 00/MBC BuyLine 3903 Superior Structural Standing Seam Roof Systems OUR PANELS MAKE THE difference www.mbci.com Superior Structural Standing Seam Roof Systems Illustrious Standing Seam Roof Systems
More informationTABLE OF CONTENTS IMAGE II. Detail Conditions. Panel Information. Flashing Profiles
TABLE OF ONTENTS Product Page No. Product Page No. Panel Information Profi les...pim-2 Panel Overview...PIM-2 Flashing Profiles Eave...PIM-3 Extended Eave...PIM-3 leat...pim-3 Offset leat...pim-3 5K Gutter...PIM-3
More informationENERGY STAR PARTNER. PBR & R Panel
ENERGY STAR PARTNER 1 Table of Contents Important Information Installation Information Technical Information Trims and Flashings Illustration Roo ng Installation Details Eave Flashing (EF-3) Eave Flashing
More information5V and CORRUGATED Accessory Detail Manual
5V and CORRUGATED Accessory Detail Manual NOA # 06-0921.07 Miami Dade Approved - 5V Only Site Specific Engineering Required Thompson Architectural Metal Roofing is proud to be a partner of the Energy Star
More informationCOMMERCIAL & INDUSTRIAL CI-CFR-INDEX SHEET INDEX CI-CFR-INDEX SHEET INDEX CI-CFR-INFO C & I DISCLAIMER
CI-CFR-INDEX SHEET INDEX CI-CFR-INFO C & I DISCLAIMER CI-CFR-LG LEGEND CI-CFR-JT-01 PANEL JOINT CI-CFR-JT-02 PANEL JOINT SEQUENCE CI-CFR-JT-03 PANEL JOINT LAYOUT CI-CFR-SQ-01 PANEL INSTALLATION SEQUENCE
More informationPBR & PBU Panels. Technical/Installation Information
PBR & PBU Panels Technical/Installation Information TABLE OF CONTENTS A. PBR Panel 1. General Description..................................................................... 2 2. Architect/Engineer Information............................................................
More informationa division of NCI Standing Seam Roof Systems
a division of NCI Standing Seam Roof Systems Building Benefits You Can Expect From A&S Materials Standing Seam roof panels weigh a relatively modest 11/2 pounds per square foot. When long life is required
More informationArchitectural Roofing
ArcTray 1. GENERAL This section deals with the supply and fixing of ArcTray overlap rigid sheet metal profiled roofing and/or cladding complete with accessories. Documents 1.1 DOCUMENTS REFERRED TO Documents
More informationPRODUCT SPECIFICATIONS
LokSeam LokSeam 12" One of the most versatile architectural metal panels available today, LokSeam by ABC, is a snap-together, concealed fastener, standing seam roof system with a 13/4" tall vertical rib,
More informationSTANDING SEAM METAL ROOFING. Presented by MBCI Credit: 1 AIA LU/HSW AIA course number: SSRLU2B
STANDING SEAM METAL ROOFING Presented by MBCI Credit: 1 AIA LU/HSW AIA course number: SSRLU2B Credit earned on completion of this course will be reported to AIA CES for AIA members. To receive a certificate
More informationSuperior Structural Standing Seam Roof Systems
07 61 00/MBC BuyLine 386 Superior Structural Standing Seam Roof Systems OUR PANELS MAKE THE difference www.mbci.com Superior Structural Standing Seam Roof Systems The Strongest Standing Seam Roof System
More informationStile. Spanish Tile Installation Guide
Stile Spanish Tile Installation Guide IMPORTANT INFORMATION THE APPLICATION AND DETAIL DRAWINGS IN THIS MANUAL ARE STRICTLY FOR ILLUSTRATION PURPOSES AND MAY NOT BE APPLICABLE TO ALL BUILDING DESIGNS OR
More informationClassic Rib Roofing Panels DETAIL MANUAL
Metal Roofing Wholesalers Classic Rib Roofing Panels DETAIL MANUAL www.metalroofingwholesalers.com 1170 Topside Rd Louisville, TN 37777 The Classic Rib Roofing Panel Figure 1 House With Classic Rib Metal
More informationw w w. s a q u l i t y m e ta l s. c o m
san antonio branch 210 W. Peden San Antonio TX 78204 P. (210) 227-7276 F. (210) 227-0329 MCALLEN branch 2221 Austin Ave McAllen TX 78501 P. (956) 627-2966 F. (956) 627-0918 w w w. s a q u l i t y m e ta
More informationCentral Seam Plus. Central-Loc
Central Seam Plus Central-Loc Product Guide HELPFUL INFORMATION ON PANELS, TRIMS, GUTTERS AND ACCESSORIES 3" 3" " or 18" COVERAGE " or 18" COVERAGE Central Seam Plus Field seamed Central-Loc Snaps together
More informationDetail Conditions. Panel Information. Flashing Profiles. Notes. Accessory Profiles. Testing Information. Design/Installation Considerations PEF-1
Table of ontents Product Page No. Product Page No. Panel Information T3 Panel Profiles... PEF-2 T3 Panel Overview... PEF-2 T6- Panel Profiles... PEF-3 T6- Panel Overview... PEF-3 T- Panel Profiles... PEF-4
More informationTREMLOCK SL INSTALLATION MANUAL
TREMLOCK SL INSTALLATION MANUAL TREMLOCK SL TremLock SL i a concealed fatener architectural tanding eam roof panel. The TremLock SL panel are eaily intalled over decking, utilizing metal clip. TremLock
More information1. Selective Demolition Section Adhered PVC Roofing System Section Sealants and Caulking Section 07920
SECTION 07620 - FLASHING AND SHEET METAL PART 1 - GENERAL 1.01 DESCRIPTION A. Work included: Provide all flashing and sheet metal not specifically described in other Sections of these Specifications but
More informationCS-100 Guide Specifications
MANUFACTURER CUSTOM-BILT METALS 1333 Corporate Drive, Suite 103 Irving, Texas 75038-2520 (800) 826-7813 or info@custombiltmetals.com www.custombiltmetals.com CS-100 Guide Specifications This Guide Specification
More informationFACE CFP - HORIZONTAL PANELS - OPTION 'B'
- Vertical Transitions 12F - H10.3 VHB TAPE 5.000" 127.0mm 5" FORMED TRANSITION STRIP w/ FLAT FACE CFP - - OPTION 'B' H10.3 CONCEALED FASTENED Panel Index 12F - H0 BASE DETAILS JOINT DETAIL PARAPET ROOF
More informationSIDEWALL/ENDWALL EXPOSED FASTENER TRIMS. Details master.dwg 2/15/2017 GULF COAST SUPPLY & MFG., LLC
CHIMNEY FLASHING CROSS SECTION 1. CHIMNEY FLASHING TRIM IS INTENDED TO FLASH AROUND CHIMNEYS AND LARGE PENETRATIONS. OTHER USE MAY BE ACCEPTABLE IF DESIGNER DETERMINES FITNESS OF USE. 3. LARGE PENETRATIONS
More informationHORIZON-LOC EXPOSED FASTENER TRIMS
Horizon -Loc Horizon-Loc is available in 6ga AZ50 painted Galvalume and bare Galvalume. Central States uses either the CentralGuard or Kynar 500 /Hylar 5000 paint system on all painted metals. Bare (non-painted)
More informationFairfield Metal 9 Audrey Place, Fairfield, NJ Phone: SEALANT COUNTER FLASHING FASTENER RAKEWALL FLASHING
SEALANT COUNTER FLASHING RAKEWALL FLASHING TUBE SEALANT Z CLOSURE FLASHING RIVET TAPE SEALANT SEE OPTION 1 & 2 NAILER TUBE SEALANT TUBE SEALANT SIDING OPTION 1 TAPE SEALANT FASTNER SILL FLASHING RAKEWALL
More informationSECTION MANUFACTURED ROOF AND WALL PANELS SECTION SHEET METAL ROOFING
SPECIFICATIONS www.englertinc.com MANUFACTURER ENGLERT, INC. 1200 Amboy Avenue Perth Amboy, New Jersey 08861 Tel: (732) 826-8614 Fax: (732) 826-8865 PART I - GENERAL 1.01 WORK INCLUDED SECTION 07410 -
More informationDrexel Metals Inc. DMC 5V 26 Gauge min. Face-Fastening Metal Roof System over Plywood
Drexel Metals Inc. DMC 5V 26 Gauge min. Face-Fastening Metal Roof System over Plywood Section 07411 Metal Roof Panels Part 1 General 1.1 Summary A. This section includes the following: a. Factory-formed
More informationcomponents your source. exceptional service
components your source. exceptional service VP Components, established in 1998, serves customers across North America by providing building components and accessories designed to meet the needs of the
More informationLokSeam. Design/Installation Information
Design/Installation Information IMPORTANT NOTICE READ THIS MANUAL COMPLETELY PRIOR TO BEGINNING THE INSTALLATION OF THE ROOFING SYSTEM. MBCI DETAILS MUST BE FOLLOWED AS A MINIMUM TO INSURE APPROPRIATE
More informationSECTION METAL ROOF PANELS
SECTION 07 41 13 PART 1 GENERAL 1.1 SECTION INCLUDES A. Standing-seam roof panels. B. Metal roofing accessories. 1.2 RELATED SECTIONS A. Section 07 62 00 - Sheet Metal Flashing. B. Section 07 72 00 - Roof
More informationProduct Guide HELPFUL INFORMATION ON PANELS, TRIMS, GUTTERS AND ACCESSORIES
5V Product Guide HELPFUL INFORMATION ON PANELS, TRIMS, GUTTERS AND ACCESSORIES ½" 24" COVERAGE Copyright 2018, Central States Manufacturing, Inc., All Rights Reserved. D C GUID_PROD_5V_180201 The men
More informationML-150. w w w. s a q u l i t y m e ta l s. c o m. san antonio branch 210 W. Peden San Antonio TX P. (210) F.
ML-150 san antonio branch 210 W. Peden San Antonio TX 78204 P. (210) 227-7276 F. (210) 227-0329 MCALLEN branch 2221 Austin Ave McAllen TX 78501 P. (956) 627-2966 F. (956) 627-0918 w w w. s a q u l i t
More informationwww.nucorbuildingsystems.com NBS - THE BRAND OF CHOICE Nucor CFR Roof Systems Foundation of Performance... 1... 2 Application and Guidelines... 3 Clip & Insulation Options... 4... 6 Warranties... 8 Details...
More informationPrestige Series 12. Installation guide
Prestige Series 12 Installation guide PIONEERING INSULATED METAL PANEL TECHNOLOGY CONTENTS Section Page Notes to Designer/User.................... 2 Panel Options............................. 3 Panel Details..............................
More information1 Exam Prep Architectural Sheet Metal Manual Tabs and Highlights
1 Exam Prep Architectural Sheet Metal Manual Tabs and Highlights These 1 Exam Prep tabs are based on the 2012 Sheet Metal and Air Conditioning Contractors' National Association, Inc., seventh edition.
More information4572 N Old US 31, Rochester, IN Toll Free: Fax: DETAIL MANUAL. and guide to Ramco Supply products
DETAIL MANUAL and guide to Ramco Supply products Metal Roofing and Siding Panels & Accessories 1 Ramco Supply s RAM Roofing Panels Ramco Supply s RAM panels are a strong, durable, economic, and attractive
More informationINSULATED PANEL OVERVIEW
INSULATED PANEL OVERVIEW Our various series of wall and roof panels are filled with non CFC polyisocyanurate foam. The panels are manufactured in a uniform pressure laminating process that bonds metal
More informationSECTION MANUFACTURED ROOF AND PANELS SECTION SHEET METAL ROOFING
SPECIFICATIONS www.englertinc.com MANUFACTURER ENGLERT, INC. 1200 Amboy Avenue Perth Amboy, New Jersey 08861 Tel: (732) 826-8614 Fax: (732) 826-8865 PART I - GENERAL 1.01 WORK INCLUDED SECTION 07410 -
More informationAgricultural Pricing Guide
Guide TABLE OF CONTENTS Panels Rain Guard Perma-Clad, WeatherSafe and Stormproof Stormproof with Drip Stop Corrugated 2 4 6 7 Accessories Flat Sheets Coils Roof Jacks Ventilators Light Transmitting Panels
More informationPanel / Trim /Accessories. Corporate Office 1500 Hamilton Rd. Bossier City, LA
Panel / Trim /Accessories Corporate Office 1500 amilton Rd. Bossier City, LA 71111 www.mcelroymetal.com MAXIMA Maxima Maxima Load Tables and Section Properties Load Tables and Section Properties for Maxima
More informationTremLock Metal Roofing and Wall Solutions
TremLock Metal Roofing and Wall Solutions ROOFING & BUILDING MAINTENANCE TABLE OF CONTENTS PRODUCT SYSTEMS OVERVIEW APPLICATION TremLock Roofing and Wall Solutions...4-5 STANDING SEAM TremLock T-138 Roof,
More informationRIB PANEL INSTALLATION
GOLDIN METALS, INC. www.goldinmetals.com 12440 SEAWAY ROAD Mailing Address: 14231 SEAWAY ROAD, SUITE 7000 GULFPORT, MS 39503 (228) 896-6216, Ext. 230 FAX (228) 896-4873 4400 PETERS ROAD P.O. BOX 700 HARVEY,
More informationGeneral Overview SECTION PBR & R PANEL - PREFORMED ROOF AND WALL PANELS
SECTION 07410 - PREFORMED ROOF AND WALL PANELS # Specifier: Notation (#) means that text following is a specifier s note or sample. PART 1 - GENERAL 1.01 Description # Specifier: Do not alter paragraph
More informationStrongSeam SSFF1 Panel
StrongSeam SSFF1 Panel Installation Manual May 2016 12 TO 24 COVERAGE CLIP OFFSET STRIATED PANEL (2 STRIATION BEADS ON PANEL) 0.875 0.9375 26 ga. & 24 ga. UL90 #529 UL2218 Class IV/Impact UL790 Class A/Fire
More informationENVELOPE The Ultimate In Performance In A Wet-Sealed System ROUT & RETURN (RR) SYSTEM TECHNICAL MANUAL
ENVELOPE 2000 ROUT & RETURN (RR) SYSTEM The Ultimate In Performance In A Wet-Sealed System TECHNICAL MANUAL System Assembly Substrate Layouts CAD Sections/Details Physical Properties Performance Properties
More informationInstallation Guide MATTERHORN METAL ROOFING TO LAST A LIFETIME. MATTERHORN Tile
Installation Guide MATTERHORN METAL ROOFING TO LAST A LIFETIME MATTERHORN Tile Watch detailed installation videos online at matterhornmetalroofing.com/tile-installation Table of Contents Accessories: Most
More informationSPECIFICATIONS FOR PROPOSED
SPECIFICATIONS FOR PROPOSED PROFILED ROOF / WALL CLADDING Client: Site address: Proposed material: Proposed profile: Rib / Seam centers: Seam height: www.archtech.co.nz 0800 252 383 info@archtech.co.nz
More information