SIDEWALL/ENDWALL EXPOSED FASTENER TRIMS. Details master.dwg 2/15/2017 GULF COAST SUPPLY & MFG., LLC

Transcription

1 CHIMNEY FLASHING CROSS SECTION 1. CHIMNEY FLASHING TRIM IS INTENDED TO FLASH AROUND CHIMNEYS AND LARGE PENETRATIONS. OTHER USE MAY BE ACCEPTABLE IF DESIGNER DETERMINES FITNESS OF USE. 3. LARGE PENETRATIONS SUCH AS CHIMNEYS MAY REQUIRE CRICKETS OR OTHER DETAILING. CHECK WITH LOCAL BUILDING CODES. 4. USE SIDEWALL DETAILS FOR CHIMNEY SIDES AND ENDWALL DETAIL FOR DOWNHILL END OF CHIMNEY. CHIMNEY FLASHING PLAN VIEW 1. VIEW AA: CHIMNEY FLASHING CROSS SECTION 2. VIEW BB: SIDE WALL CROSS SECTION, REGLET OPTION 3. VIEW CC: END WALL CROSS SECTION, REGLET OPTION 4. FLASH BEGINNING FROM DOWNHILL SIDE; OVERLAP SUCCESSIVE UPHILL FLASHING TO PROVIDE CONTINUOUS DRAINAGE PATH. METAL PANEL INSIDE CLOSURE (SEALANT ABOVE AND BELOW) CAULKED GROOVE DRIVE PIN OR OTHER SUITABLE FASTENER REGLET OR OTHER COUNTER FLASHING CHIMNEY FLASHING WRAP UP EDGE OF PENETRATION PANEL EDGE (TYP) PANEL RIB (TYP) A A ROOF PENETRATION (CHIMNEY OR SIMILAR) ROOF SLOPE B B B B ROOF DECKING C EXPOSED FASTENER CHIMNEY OR OTHER LARGE PENETRATION C CH1 DIMENSIONS 2. CH1 CAN BE USED WITH MOST PANEL PROFILES " 12" CHIMNEY FLASHING

2 EAVE CROSS SECTION 1. EAVE DRIP AND FASCIA ARE RECOMMENDED FOR USE AT ROOF EAVES. DIFFERENT STYLES OF EAVE DRIP ARE AVAILABLE SUBJECT TO DESIGNER'S SELECTION. OTHER USE MAY BE ACCEPTABLE IF DESIGNER DETERMINES FITNESS OF USE. INSIDE FASTENER EXPOSED FASTENER, TYP ED1 DIMENSIONS 1. USE DIMENSIONS SHOWN. DO NOT SCALE " " ED3 DIMENSIONS 1. USE DIMENSIONS SHOWN. DO NOT SCALE. 2. ED3 IS A 90 DRIP EDGE " 7 16 EAVE DRIP FASTENER: NAIL AT OC OR USE PANCAKE/DECK SCREW TO MATCH PANEL SPACING EAVE DRIP FACE SCREW OPTIONAL ED2 DIMENSIONS 1. USE DIMENSIONS SHOWN. DO NOT SCALE. 2. ED2 IS DESIGNED TO FIT OVER MOST ED1 STYLE EAVE DRIP. 3½" ¾" 1¾" ED3P DIMENSIONS 1. USE DIMENSIONS SHOWN. DO NOT SCALE. 2. ED3P IS FOR SLOPED ROOFS. SPECIFY PITCH OF ROOF FOR FABRICATION " ROOF DECKING FASCIA (RECOMMENDED) 1 EAVE DRIP

3 SIDEWALL/ENDWALL CROSS SECTION 1. SIDEWALL TRIM IS RECOMMENDED FOR USE WHERE A WALL INTERSECTS A ROOF SECTION PARALLELL TO THE PANEL LENGTH. ENDWALL TRIM IS RECOMMEND WHERE A WALL INTERSECTS A ROOF SECTION PERPENDICULAR TO THE PANEL LENGTH. 2. DIFFERENT STYLES OF SIDEWALL ARE AVAILABLE SUBJECT TO DESIGNER'S SELECTION. OTHER USE MAY BE ACCEPTABLE IF DESIGNER DETERMINES FITNESS OF USE. 3. DIFFERENT METHODS OF COUNTER FLASHING MAY BE USED TO PROVIDE A WEATHERTIGHT TRANSITION. 4. THIS IS A GENERIC DETAIL FOR GENERAL PURPOSE USE. SPECIAL CONDITIONS "STUCCO STOP" STYLE COUNTER FLASHING CAULK WALL FLASHING WITH INTEGRATED CAULK LIP BUTYL TAPE, TYP LOW PROFILE FASTENER SIDING OR OTHER WALL CLADDING, TYP WALL TRIM EXPOSED FASTENER, TYP DRIVE PIN OR OTHER SUITABLE FASTENER OUTSIDE CLOSURE, TYP METAL PANEL, TYP CAULK LIP STYLE COUNTER FLASHING REGLET STYLE COUNTER FLASHING SW1 DIMENSIONS 2. SW1 IS DESIGNED FOR USE WITH GULFRIB. SW4 DIMENSIONS 2. SW4 IS DESIGNED FOR USE WITH 5V CRIMP. SW5 DIMENSIONS 2. SW5 IS DESIGNED FOR USE WITH GULFPBR. EW1 DIMENSIONS 2. EW1 IS DESIGNED FOR USE WITH GULFRIB, GULFPBR, AND 5VCRIMP. EW2 DIMENSIONS 2. EW1 IS DESIGNED FOR USE WITH GULFRIB, GULFPBR, AND 5VCRIMP " 3 4 " " " 1 2 " " " " " SIDEWALL/ENDWALL CLOSED HEM

4 RIDGE CROSS SECTION ` 1. RIDGE CAP IS RECOMMENDED FOR USE AT ROOF EAVES. DIFFERENT STYLES OF RIDGE CAP ARE AVAILABLE SUBJECT TO DESIGNER'S SELECTION. OTHER USE MAY BE ACCEPTABLE IF DESIGNER DETERMINES FITNESS OF USE. MAY REQUIRE ALTERNATIVE DESIGN BY THE INSTALLER OR ARCHITECT/ENGINEER. 3. "NOTCHABLE" RIDGE CAP (RC3 & RC4) IS DESIGNED TO BE FIELD NOTCHED SO THE NOTCHED RIDGE CAP PROVIDES CLOSURE OVER THE RIBS. RC3 IS DESIGNED FOR GULF RIB AND RC4 IS DESIGNED FOR 5V. 4. CLOSURES (SOLID OR VENTED) ARE RECOMMENDED TO PROVIDE CLOSURE OVER THE RIBS. 5. USE OF VENTED CLOSURE RECOMMENDED WHEN ROOF IS DESIGNED TO VENTILATE AT THE RIDGE. EXPOSED FASTENER (THROUGH RIDGE CAP AND PANEL RIB) METAL ROOFING PANEL (TYP) RIDGE CAP (RC1, RC2, RC3, RC4, RC18, OR SIMILAR) EXPOSED FASTENER (THROUGH PANEL) DECKING VENTED OR SOLID CLOSURE, TYP (RECOMMENDED) RC1 DIMENSIONS RC3/RC4 DIMENSIONS 2. RC3 IS DESIGNED FOR GULF RIB, RC4 IS DESIGNED FOR 5V. 3. THE NOTCHABLE EDGE MUST BE CUT TO MATCH THE PROFILE OF THE PANEL RC2 DIMENSIONS RC18 DIMENSIONS 6" 6" ⅞" 4⅛" 6" ⅞" 4¾" 9" 1¼" 4⅛" RIDGE CAP

5 HIGH SIDE RIDGE CROSS SECTION 1. HIGH SIDE RIDGE CAP IS RECOMMENDED FOR USE AT THE RIDGE OF A MONOSLOPE ROOF. DIFFERENT STYLES OF RIDGE CAP ARE AVAILABLE SUBJECT TO DESIGNER'S SELECTION. OTHER USE MAY BE ACCEPTABLE IF DESIGNER DETERMINES FITNESS OF USE. 4. CLOSURES (SOLID OR VENTED) ARE RECOMMENDED TO PROVIDE CLOSURE OVER THE RIBS. 5. USE OF VENTED CLOSURE RECOMMENDED WHEN ROOF IS DESIGNED TO VENTILATE AT THE RIDGE. HS1 DIMENSIONS 2. HS1 IS DESIGNED FOR USE WITH GULFRIB. 6" CLOSURE HIGH SIDE RIDGE CAP (HS1, HS5, HS7, OR SIMILAR) METAL PANEL HS5 DIMENSIONS 2. HS5 IS DESIGNED FOR USE WITH GULFPBR. 7/16" 5½" 3½" EXPOSED FASTENER (TYP) HS7 DIMENSIONS 2. HS7 IS DESIGNED FOR USE WITH GULFLOK. 7/16" DECKING FASCIA BOARD FASCIA (FA4, FA5, FA6, OR SIMILAR) 5½" FASCIA FASTENER (NAIL OR LOW PROFILE SCREW) RECOMMENDED 12" MAX OC SPACING Details master.dwg 7/16" 2/15/2017 HIGH SIDE CAP

6 VALLEY CROSS SECTION 1. VALLEY FLASHING IS USED AT THE LOW POINT WHERE TWO ROOF SECTIONS MEET. DIFFERENT STYLES ARE AVAILABLE SUBJECT TO DESIGNER'S SELECTION. OTHER USE MAY BE ACCEPTABLE IF DESIGNER DETERMINES FITNESS OF USE. EXPANDING FOAM (TYP) MIN 6" OVERLAP METAL PANEL (TYP) VALLEY (PV1, PV2, OR SIMILAR) MIN 2" REVEAL DECKING (SELF-ADHERING RECOMMENDED FOR USE IN VALLEYS) EXPOSED FASTENER (TYP) CLOSED HEM 1" PV2 DIMENSIONS 2. PV2 CAN BE USED WITH MOST PROFILES AND FOR MOST PROJECTS 9" VALLEY

7 GABLE CROSS SECTION 1. GABLE/RAKE TRIM IS USED WHERE THE ROOF TERMINATES AT A PANEL SIDE. DIFFERENT STYLES ARE AVAILABLE SUBJECT TO DESIGNER'S SELECTION. OTHER USE MAY BE ACCEPTABLE IF DESIGNER DETERMINES FITNESS OF USE. EF1 DIMENSIONS 2. EF1 IS DESIGNED FOR USE WITH GULFRIB. 3 4 " EF4 DIMENSIONS 2. EF4 IS DESIGNED FOR USE WITH 5VCRIMP. 1 2 " GABLE RAKE TRIM EXPOSED FASTENER, TYP 7 16 " " BUTYL TAPE EF1B DIMENSIONS 2. EF1B S DESIGNED FOR USE WITH GULFRIB AND HAS A LONGER VERTICAL FACE FOR USE OVER BATTENS EF5 DIMENSIONS 2. EF5 IS DESIGNED FOR USE WITH GULFPBR " 3 4 " " " METAL PANEL (PBR SHOWN) " ROOF DECK 7 16 " 7 16 " RAFTER OR OTHER STRUCTURAL MEMBER FASCIA GABLE

8 GF1 DIMENSIONS 2. GF1 IS SUITABLE FOR USE WITH MOST PANEL PROFILES " METAL PANEL, TYP " INSIDE CLOSURE ROOF DECKING GAMBREL FLASHING, GF-1 OR SIMILAR INSTALL UNDER TOP PANEL AND OVER BOTTOM PANEL GAMBREL CROSS SECTION 1. GAMBREL FLASHING IS USED AT THE POINT WHERE ROOF SLOPES CHANGE. DIFFERENT STYLES ARE AVAILABLE SUBJECT TO DESIGNER'S SELECTION. OTHER USE MAY BE ACCEPTABLE IF DESIGNER DETERMINES FITNESS OF USE. OUTSIDE CLOSURE GAMBREL

9 METAL PANEL, TYP " TF1 DIMENSIONS 2. TF1 IS DESIGNED FOR USE WITH GULFRIB, GULFPBR, AND 5VCRIMP " EXPOSED FASTENER, TYP CLOSED HEM INSIDE CLOSURE TRANSITION FLASHING INSTALL UNDER TOP PANEL AND ABOVE BOTTOM PANEL OUTSIDE CLOSURE ROOF DECKING TRANSITION CROSS SECTION 1. TRANSITION FLASHING IS USED AT THE POINT WHERE ROOF SLOPES CHANGE. DIFFERENT STYLES ARE AVAILABLE SUBJECT TO DESIGNER'S SELECTION. OTHER USE MAY BE ACCEPTABLE IF DESIGNER DETERMINES FITNESS OF USE. 2. USE OF A LONGER TRANSITION FLASHING IS NECESSARY WHEN THE DIFFERENCE BETWEEN SLOPES IS SMALL. 3. THIS IS A GENERIC DETAIL FOR GENERAL PURPOSE USE. SPECIAL CONDITIONS TRANSITION

10 VENT PIPE OR SIMILAR PENETRATION PIPE BOOT FASTENER, TYP SEALANT BETWEEN PANEL AND BASE OF PIPE BOOT PIPE BOOT PLAN VIEW 1. PIPE BOOTS ARE DESIGNED TO FLASH AROUND PIPES AND SIMILAR PENETRATIONS. 2. TYPICAL INSTALLATION PROCESS: CUT OPENING OF PIPE BOOT TO FIT TIGHTLY AROUND PIPE. APPLY SEALANT TO BASE OF PIPE BOOT. SLIDE BOOT OVER PIPE. FORM TO ROOF PROFILE. FASTEN PIPE BOOT WITH FASTENERS AT 1-2" OC OR AS REQUIRED TO ENSURE TIGHT FIT. APPLY ADDITIONAL SEALANT AS REQUIRED. 3. WHENEVER POSSIBLE, PLACE THE PENETRATION IN THE CENTER OF THE PAN. IF PENETRATION MUST FALL ON PANEL RIB, PIPE BOOT MAY BE INSTALLED ON RIB. EXTREME CARE MUST BE EXERCISED TO ENSURE THE BASE OF THE PIPE BOOT HAS SUFFICIENT SEALANT, THAT THE BASE IS WELL FORMED TO THE RIB, AND THAT SUFFICIENT FASTENERS ARE USED TO MAINTAIN A WATERTIGHT SEAL. APPLY ADDITIONAL SEALANT AFTER INSTALLATION IF REQUIRED. 4. SIZE PIPE BOOT TO FIT THE PIPE/PENETRATION AND PANEL IN USE. 5. THIS IS A GENERIC DETAIL FOR GENERAL PURPOSE USE. SPECIAL CONDITIONS 6. IF CONSTRAINT OF THERMAL MOVEMENT IS A CONCERN FOR LONG PANEL RUNS, DESIGNER SHOULD CONSIDER INSTALL OPTIONS TO AVOID PINNING ROOF PANEL TO THE ROOF DECK. PANEL RIB, TYP Details master.dwg 7/72017 GENERAL TRIMS PIPE BOOT