HARNETT COUNTY FINANCE/PURCHASING

Transcription

1 HARNETT COUNTY FINANCE/PURCHASING REQUEST FOR QUOTES WATER AND WASTEWATER TREATMENT CHEMICALS FOR HARNETT COUNTY DEPARTMENT OF PUBLIC UTILITIES FIRM QUOTES FOR SUPPLIES AND DELIVERY FOR THE PERIOD OF JULY 1, 2010 THROUGH JUNE 30, 2011 DUE DATE: NO LATER THAN 12:00 NOON JULY 15, 2010 OPENING DATE: JULY 15, 2010 TIME: 12:00 NOON LOCATION: HARNETT COUNTY PUBLIC UTILITIES BUSINESS CENTER 700 McKINNEY PARKWAY LILLINGTON, NC CONFERENCE ROOM 101A QUESTIONS: ALLAN O BRIANT, WATER PLANT SUPERVISOR P.O. BOX 1119, LILLINGTON, N.C (910) x3238 AOBRIANT@HARNETT.ORG FAXES OR S ARE NOT ACCEPTED FOR THIS QUOTE THE COUNTY OF HARNETT RESERVES THE RIGHT TO REJECT ANY OR ALL BIDS RECEIVED, OR TO SELECT THE BID WHICH, IN OUR OPINION, IS THE BEST OVERALL INTEREST OF THE COUNTY. MAIL OR DELIVER QUOTES IN A SEALED ENVELOPE IDENTIFIED QUOTE ENCLOSED PUWW , YOUR FIRM NAME AND THE OPENING DATE ON THE OUTSIDE OF THE ENVELOPE TO: Kimberly Honeycutt Finance & Budget Analyst 102 E. Front Street P.O. Box 760 Lillington, N.C Page 1 of 40

2 Harnett County Department of Public Utilities Request for Quotes Water and Wastewater Treatment Chemicals Harnett County (the County ) is soliciting firm quotes for the purchase and delivery of water and wastewater chemicals for the period from July 1, 2010 through June 30, Purchases will be in full tanker truck loads (TTL), LTL, totes, pallet loads or as noted below. All pricing is delivered. No fuel surcharges will be considered unless spot diesel fuel prices for over the road vehicles rise above $3.50 per gallon for 60 consecutive days. GENERAL SPECIFICATIONS & INSTRUCTIONS TO BIDDERS Scope It is the intent of this request for quotes to obtain proposals for supplying the materials, supplies and/or equipment listed in the Bid Proposal Sheets, attached hereto and hereby incorporated herein. Compliance with Specifications Supplier s quote must be in strict compliance with the specifications and offer the same or equal materials. (HCDPU) reserves the right to allow or disallow minor deviations from the specifications in order to purchase what best meets the needs of the County from a standpoint of quality, price and service to be rendered. Warranty In submitting a quote, the bidder warrants that all goods furnished shall be free from all defects and shall conform in all respects to the technical specifications established herein. The bidder expressly warrants that all items bid are fit and sufficient for their intended purpose. Shipping All prices are to be quoted F.O.B. delivered, unless otherwise specified. Risk of loss and/or damage shall be upon the seller until such time as the goods have been physically delivered and accepted by the County. LTL deliveries shall be made by the supplier submitting the quote. No subcontracting of these deliveries is allowed. Unit Prices to Prevail Prices shall be submitted on per unit basis by line item. In the event of a disparity between the unit price and the extended price, the unit price shall prevail. Bid Price Corrections No corrections will be permitted after bid opening. Use of Brand Names And References Page 2 of 40

3 Unless otherwise stated, the use of manufacturer's names and product numbers are for descriptive purposes and establishing general quality levels only. Rejection of Bids The County reserves the right to reject any and all bids. Award Award shall be made to the lowest responsible bidder (also referred to as Supplier ) for each item taking into consideration quality, performance and time specified in the proposal for the performance of the contract. Time of delivery and prompt payment discounts will be considered in breaking tie bids. Harnett County reserves the right to award individual bids for each chemical requested or to combine any and all bids dependent upon meeting the best interests of the County. Bidders may provide pricing for one or more items and are not required to submit pricing or forms for those items not bid. Taxes Harnett County is exempt from and will not pay federal taxes. An exemption certificate will be furnished upon request. North Carolina and local sales tax shall be shown as a separate item. Sales tax will not be a consideration in the award. Payment Upon complete delivery and receipt of a correct invoice, payment will be made by County Net 30. Terms and Conditions Terms and Conditions included herein are an integral part of the bid document and shall prevail unless changes or attachments are agreed to and initialed by Harnett County prior to the bid opening. Terms and Conditions attached to the bid by the bidder and made a condition of purchase may render the bid nonresponsive and may be rejected by Harnett County. Default Failure to satisfactorily perform the services required by the contract for the project will be grounds for County to declare the successful bidder in default. Unless otherwise provided herein, the contract may be canceled or annulled with a 30-day notice by County in whole or in part by written notice of default to the bidder upon nonperformance or violation of contract terms. An award may be made to another bidder for services specified, or they may be purchased on the open market and the defaulting supplier shall be liable to County for costs to the County in excess of the defaulted contract prices. The bidder shall continue the performance of this contract to the extent that any part is not terminated under the provisions of this clause. Training/Safety When requested or required, a factory trained representative shall be made available to train County personnel in the use of and/or safety aspects of the equipment or chemical. The successful bidder shall provide a Material Safety Data Sheet (MSDS) for each product prior to the first delivery. The supplier/transporter shall be responsible for adhering to all federal, state and local safety rules and regulations. All supplier/transporter employees shall adhere to all safety practices and use of approved PPE during off loading chemicals. The supplier/transporter shall be responsible for any and all chemical spills during off loading of chemicals (containment, cleanup and abatement) in accordance with the facility s written SPCC plan. Page 3 of 40

4 Contractor s Representative for Business Purposes The name, mailing address, electronic mail address, facsimile number, and telephone number of the supplier's authorized agent with authority to bind the firm and answer official questions concerning the supplier s proposal must be clearly stated. Leaking Containers During Shipment All containers delivered will be inspected for leakage upon arrival and prior to unloading. Leaking containers will not be unloaded and accepted by the County. Response and remediation for any containers determined to be leaking shall remain the responsibility of the transporter. Dented or damaged chlorine cylinders will not be accepted and will be rejected at delivery. Removal of the rejected cylinders will be the supplier s responsibility. Tie Bids In the event of identical bids, the County will base its award recommendation on the following basis: (1) prior service records; and (2) type equipment utilized to service the County. Indemnity and Insurance Bidder will indemnify and hold harmless the County, its officers, agents, and employees from and against all loss, cost, damages, expense and liability caused by accident or other occurrence resulting in bodily injury, including death and disease to any person, or damage or destruction to property, real or personal, arising directly or indirectly from operations, products, or services rendered or purchased under the contract. Bidder, at its sole expense, will purchase and maintain the insurance listed below as A, B, & C. A. Automobile Automobile bodily injury and property damage liability insurance in an aggregate amount of at least $1,000, B. Commercial General Liability-Bodily injury and property damage liability as will protect bidder from claims of bodily injury or property damages which arise from operations of this contract. The amounts of such insurance coverage shall not be less than $2,000, per occurrence and $3,000, aggregate coverage. This insurance shall include coverage for products/completed operations, personal injury liability and contractual liability. C. Workers Compensation and employers liability meeting the statutory requirements of the State of North Carolina. The successful bidder shall provide the County with a certificate of such insurance which shall name County as an additional insured and contain the provision that the County will be given thirty (30) days written notice of any intent to amend or terminate by either the insured or the insuring company. However, a ten (10) day notice is sufficient for cancellation due to non-payment of premium. Equal Opportunity Employer Harnett County is an equal employment opportunity employer. The County is a federal contractor, and therefore the provisions and affirmative action obligations of 41 CFR (a), 41 CFR (a), and 41 CFR are incorporated herein by reference, where applicable. Other 1. Certified copy of chemical analysis shall accompany bid and each delivery. 2. Delivery shall be made F.O.B. plants as directed at time order is placed. 3. Prices shall include loading, unloading, pumping, pallet and all charges related to delivery. Page 4 of 40

5 4. Unit prices calculated other than as requested on the bid proposal sheet will not be considered. Questions Please direct all questions concerning the specifications, the RFQ, points of delivery, etc. to Allan O Briant, Water Plant Supervisor, PO Box 1119, Lillington, NC 27546, (910) x3238 or aobriant@harnett.org. Page 5 of 40

6 Item 1. FLUOROSILICIC ACID BID PROPOSAL Estimated Quantity 40,000 lbs Quote TTL Price per lb dry weight The cost of this chemical varies due to strength. Provide the formula used for calculating the delivered cost from the unit price using the wet weight delivered and chemical analysis. Failure to include the formula may be grounds for dismissal of bid. Manufacturer Brand Notes: In addition to the detailed specifications, the following requirements pertain: 1. Delivery of approximately 45,000 pounds, liquid (TTL) of Fluorosilicic Acid to be made to the water plant from time to time as required by. 2. Delivery shall be made within 72 hours of request between the hours of 8:00 a.m. and 3:30 p.m., Monday through Friday. Item % LIQUID ALUMINUM SULFATE Estimated Quantity 900 Dry Tons Quote TTL Price per dry ton The cost of this chemical varies due to strength. Provide the formula used for calculating the delivered cost from the unit price using the wet weight delivered and chemical analysis. Manufacturer Brand Notes: In addition to the detailed specifications, the following requirements pertain: 1. Delivery of approximately 45,000 pounds (TTL) of 8.3% Liquid Aluminum Sulfate to be made from time to time as required by. 2. Delivery shall be made within 72 hours of request between the hours of 8:00 a.m. and 3:30 p.m., Monday through Friday. Item 3. SODIUM HYPOCHLORITE, 15% Estimated Quantity 220,000 lbs Quote TTL Price per lb available chlorine Estimated Quantity 9,200 gals Quote LTL Price per lb available chlorine The cost of this chemical varies due to strength. Provide the formula used for calculating the delivered cost from the unit price using the wet weight delivered and chemical analysis. Failure to include the formula may be grounds for dismissal of bid. Manufacturer Brand Notes: In addition to the detailed specifications, the following requirements pertain: 1. Delivery of approximately 45,000 pounds (TTL) of Sodium hypochlorite to the water plant and wastewater plants or 500-1,000 gallons (LTL) to be made to the Erwin WWTPS, South 20 th St, Erwin, NC from time to time as required by. Page 6 of 40

7 2. Delivery shall be made within 72 hours of request between the hours of 8:00 a.m. and 3:30 p.m., Monday through Friday. Item 4. Sodium Chlorite (25%) Estimated Quantity 225,000 lbs Quote TTL Price per lb The cost of this chemical varies due to strength. Provide the formula used for calculating the delivered cost from the unit price using the wet weight delivered and chemical analysis. Failure to include the formula may be grounds for dismissal of bid. Manufacturer Brand Notes: In addition to the detailed specifications, the following requirements pertain: 1. Delivery of approximately 45,000 pounds (TTL) of sodium chlorite to be made from time to time as required by. 2. Delivery shall be made within 240 hours of request between the hours of 8:00 a.m. and 3:30 p.m., Monday through Friday. 3. This specification includes a service clause for the existing feed equipment Item 5. Chlorine Gas 150 lb Cylinders Estimated Quantity 30,000 lbs in 150 lb cylinders Quote Price per lb Manufacturer Brand Notes: In addition to the detailed specifications, the following requirements pertain: 1. Delivery of approximately 3-6 cylinders to the water plant from time to time as required by. 2. Delivery shall be made within 72 hours of request between the hours of 8:00 a.m. and 3:30 p.m., Monday through Friday. Item 6a. CAUSTIC SODA (SODIUM HYDROXIDE, 50%) Estimated Quantity 150 Dry Tons Quote TTL Price per dry ton Estimated Quantity 15,000 gallons Quote LTL Price per dry ton Item 6b. CAUSTIC SODA (SODIUM HYDROXIDE, 25%) Estimated Quantity 11,000 gallons Quote LTL Price per dry ton The cost of this chemical varies due to strength. Provide the formula used for calculating the delivered cost from the unit price using the wet weight delivered and chemical analysis. Failure to include the formula may be grounds for dismissal of bid. Manufacturer Brand Notes: In addition to the detailed specifications, the following requirements pertain: 1. Delivery of approximately 45,000 pounds (TTL) of Caustic Soda (50%) to the water plant and 500-1,000 gallons (LTL, 50%/25%) to be made to the Erwin WWTP, 411 South 20 th St, Erwin, NC from time to time as required by. 2. Delivery shall be made within 72 hours of request between the hours of 8:00 a.m. and 3:30 p.m., Monday through Friday. Page 7 of 40

8 Item 7. 93% Sulfuric Acid Estimated Quantity 245,000 lbs Quote TTL Price per lb $ LTL $ The cost of this chemical varies due to strength. Provide the formula used for calculating the delivered cost from the unit price using the wet weight delivered and chemical analysis. Failure to include the formula may be grounds for dismissal of bid. Manufacturer Brand Notes: In addition to the detailed specifications, the following requirements pertain: 1. Delivery of approximately 45,000 pounds (TTL) or (LTL) of 93% Liquid Sulfuric Acid to be made from time to time as required by. 2. Delivery shall be made within 72 hours of request between the hours of 8:00 a.m. and 3:30 p.m., Monday through Friday. 3. The bulk tank for this chemical should be installed by November Item 8. SODIUM BISULFITE, 38% Estimated Quantity 11,000 gals LTL Price per lb $ The cost of this chemical varies due to strength. Provide the formula used for calculating the delivered cost from the unit price using the wet weight delivered and chemical analysis. Failure to include the formula may be grounds for dismissal of bid. Manufacturer Brand Notes: In addition to the detailed specifications, the following requirements pertain: 1. Delivery of approximately 500-1,000 gallons (LTL) or one or more totes of sodium bisulfite to be made to the Erwin WWTPS, South 20 th St, Erwin, NC from time to time as required by Harnett County Department of Public Utilities. 2. Delivery shall be made within 72 hours of request between the hours of 8:00 a.m. and 3:30 p.m., Monday through Friday. Item 9. AQUEOUS AMMONIA Estimated Quantity 25 tons Quote TTL Price per lb The cost of this chemical varies due to strength. Provide the formula used for calculating the delivered cost from the unit price using the wet weight delivered and chemical analysis. Failure to include the formula may be grounds for dismissal of bid. Manufacturer Brand Notes: In addition to the detailed specifications, the following requirements pertain: 1. Delivery of approximately 45,000 lbs (19.2%) to the water plant from time to time as required by. 2. Delivery shall be made within 72 hours of request between the hours of 8:00 a.m. and 3:30 p.m., Monday through Friday. Page 8 of 40

9 Item10. Copper Sulfate Estimated Quantity 10,000 lbs Quote Price per lb. Manufacturer Brand Notes: In addition to the detailed specifications, the following requirements pertain: 1. Delivery of approximately 1,250-2,000 pounds (in 50 lb bags or pails) of copper sulfate to be made from time to time as required by. 2. Delivery shall be made within 120 hours of request between the hours of 8:00 a.m. and 3:30 p.m., Monday through Friday. Item 11. POWDERED ACTIVATED CARBON SLURRY (2 lbs PAC per Gallon) Estimated Quantity 90,000 gals Quote TTL Price per lb Manufacturer Brand Notes: In addition to the detailed specifications, the following requirements pertain: 1. Delivery of approximately 45,000 pounds (TTL) of a two lb/gallon powdered activated carbon slurry to be made from time to time as required by. 2. Delivery shall be made within 72 hours of request between the hours of 8:00 a.m. and 3:30 p.m., Monday through Friday. Item 12. Aqua Mag Estimated Quantity 18,000 gals Quote TTL Price per lb wet weight. Manufacturer: Carus Brand: Aqua Mag Notes: In addition to the detailed specifications, the following requirements pertain: 1. Delivery of approximately 45,000 pounds (TTL) to the water plant from time to time as required by. 2. Delivery shall be made within 72 hours of request between the hours of 8:00 a.m. and 3:30 p.m., Monday through Friday. 3. No substitutes. Item13. Odor Klean Estimated Quantity 110,000 gals Quote LTL Price per lb wet weight. Does the cost of this chemical vary due to strength? Yes No If so, please provide the formula for calculating the cost Manufacturer Brand Notes: In addition to the detailed specifications, the following requirements pertain: 1. Delivery of approximately 2,000 gallons split between multiple sites of Odor Klean or one or more totes to be made from time to time as required by Harnett County Department of Public Utilities. Page 9 of 40

10 2. Delivery shall be made within 72 hours of request between the hours of 8:00 a.m. and 3:30 p.m., Monday through Friday. Item14. Lime Slurry Estimated Quantity 700,000 lbs Quote TTL Price per lb wet weight. Estimated Quantity 110,000 gals Quote Partial Deliveries Price per lb wet weight. Does the cost of this chemical vary due to strength? Yes No If so, please provide the formula for calculating the cost. Failure to include the formula may be grounds for dismissal of bid. Manufacturer Brand Notes: In addition to the detailed specifications, the following requirements pertain: 1. Delivery of approximately 45,000 pounds (TTL) of Lime Slurry to the water plant and North Harnett Regional WWTP, partial load deliveries to the, Erwin WWTPs, South Central WWTP and other locations from time to time as required by. 2. Delivery shall be made within 72 hours of request between the hours of 8:00 a.m. and 3:30 p.m., Monday through Friday. 3. This bid contains an equipment supply and service specification. Page 10 of 40

11 Product Specifications 1.1 Scope ITEM NO. 1 HYDROFLUOROSILICIC ACID Hydrofluorosilicic acid (H 2 SiF 6 ) supplied under the contract shall conform to all provisions of ANSI/AWWA B Standard or the latest revision. This specification covers hydrofluorosilicic acid (HFS) for water supply service applications. The estimated annual usage is 17,000 gallons. The bid price and billing price on this product will be on a wet weight basis for 23% HFS. 1.2 Purpose The purpose of this specification is to provide manufacturers and suppliers with the minimum requirements for hydrofluorosilicic acid, including physical, chemical, packaging, shipping, and testing requirements. 1.3 Physical Requirements The fluorosilicic acid supplied under these specifications shall be clean and free of visible suspended matter. The fluorosilicic acid supplied under this specification shall be water white to straw yellow. Straw yellow shall be determined as material with a maximum of 100 units in accordance with Standard Methods 2120B, Visual Comparison Method. 1.4 Chemical Requirements The fluorosilicic acid shall contain between 20 and 30 percent fluorosilicic acid by weight. 1.5 Impurities General. Fluorosilicic acid that meets the requirements of this specification shall contain no mineral or organic substances in quantities capable of producing deleterious or injurious effects on the health of those consuming water that has been properly treated with fluorosilicic acid Specific Impurity Limits. The fluorosilicic acid supplied under this specification shall contain a maximum of 1 percent free acids (other than fluorosilicic acid), expressed as HF (hyfrofluoric acid). 1.6 Sampling and Analysis Sampling. Samples requested by a Harnett County employee shall be taken by the driver at the point of delivery and in the presence of a Harnett County employee. The sample shall be placed in a container that will be provided by the County, which shall include a label to be completed by the driver collecting the sample. The sample shall be given to the Harnett County employee for processing Tank Samples. The sample taken by the driver should be a representative sample of the product delivered. Samples shall be held by County for 30 days before disposal Analysis. No independent analysis of the provided samples will be performed by an outside laboratory unless it is deemed necessary for product verification. A Harnett County employee supervising chemical delivery may perform simple tests such as specific gravity, ph or strength of product on the product before it is Page 11 of 40

12 accepted for offloading into the County s storage vessels. 1.7 Rejection Notice of Nonconformance. If the fluorosilicic acid delivered does not meet the requirements of ANSI/AWWA B standard, a notice of nonconformance shall be given to the supplier by County within ten days of County s discovery of nonconformance. County shall have the right to reject all nonconforming product Material Originating Outside of North America. No material shall be supplied under this contract that was manufactured outside of North America without written approval of the County. The supplier shall inform the County, in writing, that the material was manufactured outside of North America, the origin of the material, and certification of conformance with ANSI/AWWA B Standard. 1.8 Affidavit of Compliance The County requires (1) an affidavit from the manufacturer that the fluorosilicic acid furnished under these specifications complies with all applicable requirements of ANSI/AWWA B Standard. (2) A certified analysis of the fluorosilicic acid and a certified weight certificate shall be furnished by the supplier with each shipment. The analysis shall include product content Product Certifications. Fluorosilicic acid is a direct additive used in the treatment of potable water. This material should be certified as suitable for contact with or treatment of drinking water by an accredited certification organization in accordance with ANSI/NSF Standard 60, Drinking Water Treatment Chemicals - Health Effects. Evaluation shall be accomplished in accordance with requirements that are no less restrictive than those listed in ANSI/NSF Standard 60. Certification shall be accomplished by a certification organization accredited by the American National Standards Institute. 1.9 CHEMICAL SPILL RESPONSE REQUIREMENTS Hazmat Response Team. Each chemical supplier shall furnish the name, address and telephone number of a qualified Hazmat Response Team. This team shall be supplied by the supplier to clean-up and mitigate a chemical spill caused by the supplier or its designee. The Hazmat Response Team must meet OSHA requirements and be available twenty-four (24) hours per day, seven (7) days per week Spill Response. Response to a hazardous material clean-up shall occur within eight (8) hours of notification by the treatment plant or the authorized representative, Spill mitigation actions taken by PWD personnel shall not be construed as a replacement for Chemical Spill Response. The Water Resources Manager or authorized designee shall make the determination of need for Hazmat Response Team assistance. Supplier must supply information on response team prior to first shipment. 2.0 PACKAGING & SHIPPING Packaging and shipping of all fluorosilicic acid solutions shall conform to all applicable local, state and federal regulations (including USDOT regulations and applicable interstate regulations). Page 12 of 40

13 ITEM NO. 2 LIQUID ALUMINUM SULFATE 1.1 Scope Liquid Aluminum Sulfate supplied under the contract shall conform to all provisions of ANSI/AWWA B Standard or the latest revision. This specification covers purified aluminum sulfate in liquid form for use in water treatment. The estimated annual usage is 900 dry tons. Pricing is requested for full truck loads (TTL) on a dry weight basis. 1.2 Purpose The purpose of this specification is to provide manufacturers and suppliers with the minimum requirements for aluminum sulfate, including physical, chemical, packaging, shipping, and testing requirements. 1.3 Physical Requirements Liquid alum shall be of such clarity as to permit the reading of flow-measuring devices without difficulty. 1.4 Chemical Requirements Liquid alum shall contain water-soluble aluminum of not less than 4.23 percent as AL or 8.0 percent as Al 0. The 2 3 water-soluble matter shall not exceed 0.2 percent in liquid alum. 1.5 Impurities General. Aluminum sulfate that meets the requirements of this standard shall contain no soluble material or organic substances in quantities capable of producing deleterious or injurious effects on the health of those consuming water that has been treated properly with the aluminum sulfate Specific Impurity Limits. The total water-soluble iron (expressed as Fe2O3) content of aluminum sulfate shall be no more than 0.75 percent, on a basis of 17 percent Al2O3 (9 percent as Al), in dry aluminum sulfate; or 0.35 percent, on a basis of 8.0 percent Al2O3 (4.23 percent as Al), in liquid aluminum sulfate. 1.6 Sampling and Analysis 1.6 Sampling and Analysis Sampling. Samples requested by a Harnett County employee shall be taken by the driver at the point of delivery and in the presence of a Harnett County employee. The sample shall be placed in a container that will be provided by the County, which shall include a label to be completed by the driver collecting the sample. The sample shall be given to the Harnett County employee for processing Tank Samples. The sample taken by the driver should be a representative sample of the product delivered. Samples shall be held by County for 30 days before disposal. Page 13 of 40

14 1.7 Rejection Analysis. No independent analysis of the provided samples will be performed by an outside laboratory unless it is deemed necessary for product verification. A Harnett County employee supervising chemical delivery may perform simple tests such as specific gravity, ph or strength of product on the product before it is accepted for offloading into the County s storage vessels Notice of Nonconformance. If the aluminum sulfate delivered does not meet the requirements of ANSI/AWWA B standard, a notice of nonconformance shall be given to the supplier by County within ten days of County s discovery of nonconformance. County shall have the right to reject all nonconforming product Material Originating Outside of North America. No material shall be supplied under this contract that was manufactured outside of North America without written approval of the County. The supplier shall inform the County, in writing, that the material was manufactured outside of North America, the origin of the material, and certification of conformance with ANSI/AWWA B Standard. 1.8 Affidavit of Compliance The County requires (1) an affidavit from the manufacturer that the fluorosilicic acid furnished under these specifications complies with all applicable requirements of ANSI/AWWA B Standard. (2) A certified analysis of the aluminum sulfate and a certified weight certificate shall be furnished by the supplier with each shipment. The analysis shall include product content Product Certifications. Aluminum sulfate is a direct additive used in the treatment of potable water. This material should be certified as suitable for contact with or treatment of drinking water by an accredited certification organization in accordance with ANSI/NSF Standard 60, Drinking Water Treatment Chemicals - Health Effects. Evaluation shall be accomplished in accordance with requirements that are no less restrictive than those listed in ANSI/NSF Standard 60. Certification shall be accomplished by a certification organization accredited by the American National Standards Institute. 1.9 CHEMICAL SPILL RESPONSE REQUIREMENTS Hazmat Response Team. Each chemical supplier shall furnish the name, address and telephone number of a qualified Hazmat Response Team. This team shall be supplied by the supplier to clean-up and mitigate a chemical spill caused by the supplier or its designee. The Hazmat Response Team must meet OSHA requirements and be available twenty-four (24) hours per day, seven (7) days per week Spill Response. Response to a hazardous material clean-up shall occur within eight (8) hours of notification by the treatment plant or the authorized representative, Spill mitigation actions taken by PWD personnel shall not be construed as a replacement for Chemical Spill Response. The Water Resources Manager or authorized designee shall make the determination of need for Hazmat Response Team assistance. Supplier must supply information on response team prior to first shipment. 2.0 PACKAGING & SHIPPING Packaging and shipping of liquid aluminum sulfate shall conform to all applicable local, state and federal regulations (including USDOT regulations and applicable interstate regulations). Page 14 of 40

15 ITEM NO. 3 SODIUM HYPOCHLORITE 1.1 Scope Sodium hypochlorite supplied under this specification shall conform to all provisions of AWWA B Standard. This specification covers sodium hypochlorite for use in water treatment. The estimated annual usage is 220,000 gallons for full truck loads (TTL) and 9,200 gallons for less than truck loads (LTL). Pricing will be on the basis of pounds available chlorine by weight. 1.2 Purpose The purpose of this specification is to provide manufacturers and suppliers with the minimum requirements for sodium hypochlorite, including physical, chemical, packaging, shipping, and testing requirements. 1.3 Physical Requirements Sodium Hypochlorite solution shall be a clear light-yellow liquid containing up to 200 g/l available chlorine (20 percent). Sodium hypochlorite shall not contain more than 0.15 percent insoluble matter by weight. 1.4 Chemical Requirements Sodium hypochlorite delivered under this contract shall have a minimum of 120 grams per liter available chlorine equivalent to 12 percent sodium hypochlorite by weight. 1.5 Impurities General. The sodium hypochlorite supplied according to this specification shall contain no soluble material or organic substances in quantities capable of producing deleterious effects on the health of those consuming water that has been treated properly with the sodium hypochlorite Specific Impurity Limits. The total free alkali (expressed as NaOH) in sodium hypochlorites shall not exceed 1.5 percent by weight. Sodium hypochlorite delivered under this contract shall meet the following containment concentration limits: Iron < 0.3 mg/l Copper < 0.03 mg/l Nickel < 0.03 mg/l Chlorate < 2,500 mg/l Bromate 20 mg/l 1.6 Sampling and Analysis Sampling. Samples requested by a Harnett County employee shall be taken by the driver at the point of delivery and in the presence of a Harnett County employee. The sample shall be placed in a container that will be provided by the County, which shall include a label to be completed by the driver collecting the sample. The sample shall be given to the Harnett County employee for processing Tank Samples. The sample taken by the driver should be a representative sample of the product delivered. Samples shall be held by County for 30 days before disposal Analysis. No independent analysis of the provided samples will be performed by an outside laboratory unless it is deemed necessary for product verification. A Harnett County employee supervising chemical delivery may perform simple tests such as specific gravity, ph or strength of product on the Page 15 of 40

16 product before it is accepted for offloading into the County s storage vessels. 1.7 Rejection Notice of Nonconformance. If the sodium hypochlorite delivered does not meet the requirements of ANSI/AWWA B standard, a notice of nonconformance shall be given to the supplier by County within ten days of County s discovery of nonconformance. County shall have the right to reject all nonconforming product Material Originating Outside of North America. No material shall be supplied under this contract that was manufactured outside of North America without written approval of the County. The supplier shall inform the County, in writing, that the material was manufactured outside of North America, the origin of the material, and certification of conformance with ANSI/AWWA B Standard. 1.8 Affidavit of Compliance The County requires (1) an affidavit from the manufacturer that the sodium hypochlorite furnished under these specifications complies with all applicable requirements of ANSI/AWWA B Standard. (2) A certified analysis of the sodium hypochlorite and a certified weight certificate shall be furnished by the supplier with each shipment. The analysis shall include product content Product Certifications. Sodium hypochlorite is a direct additive used in the treatment of potable water. This material should be certified as suitable for contact with or treatment of drinking water by an accredited certification organization in accordance with ANSI/NSF Standard 60, Drinking Water Treatment Chemicals - Health Effects. Evaluation shall be accomplished in accordance with requirements that are no less restrictive than those listed in ANSI/NSF Standard 60. Certification shall be accomplished by a certification organization accredited by the American National Standards Institute. Sodium hypochlorite is required to be registered with USEPA under FIFRA. 1.9 CHEMICAL SPILL RESPONSE REQUIREMENTS Hazmat Response Team. Each chemical supplier shall furnish the name, address and telephone number of a qualified Hazmat Response Team. This team shall be supplied by the supplier to clean-up and mitigate a chemical spill caused by the supplier or its designee. The Hazmat Response Team must meet OSHA requirements and be available twenty-four (24) hours per day, seven (7) days per week Spill Response. Response to a hazardous material clean-up shall occur within eight (8) hours of notification by the treatment plant or the authorized representative, Spill mitigation actions taken by PWD personnel shall not be construed as a replacement for Chemical Spill Response. The Water Resources Manager or authorized designee shall make the determination of need for Hazmat Response Team assistance. Supplier must supply information on response team prior to first shipment. 2.0 PACKAGING & SHIPPING Packaging and shipping of all sodium hypochlorite solutions shall conform to all applicable local, state and federal regulations (including USDOT regulations and applicable interstate regulations). Page 16 of 40

17 ITEM NO. 4 SODIUM CHLORITE 1.1 Scope Sodium chlorite supplied under this specification shall conform to all provisions of AWWA B Standard. This specification covers sodium chlorite for use in the generation of chlorine dioxide for use in water treatment. The estimated annual usage is 225,000 pounds. Pricing is requested for full truck loads (TTL). This product specification includes a service requirement listed as Item No. 15, below. 1.2 Purpose The purpose of this specification is to provide manufacturers and suppliers with the minimum requirements for sodium chlorite, including physical, chemical, packaging, shipping, and testing requirements. 1.3 Physical Requirements Sodium chlorite solution shall be clear, or a light-tan to straw brown color. Sodium chlorite shall have a clarity that permits the reading of flow-measuring devices. 1.4 Chemical Requirements Sodium chlorite delivered under this contract shall have a minimum of 77.5 percent by weight NaClO 2 (25%). 1.5 Impurities General. The sodium chlorite supplied according to this specification shall contain no soluble material or organic substances in quantities capable of producing deleterious effects on the health of those consuming water that has been treated properly with the sodium chlorite Specific Impurity Limits. Sodium chlorite based on 80 percent sodium chlorite content shall contain no more than the following percentages of specific impurities by weight: 1.6 Sampling and Analysis Sodium Chloride, 17% Sodium Hydroxide, 3 % Arsenic, % Sodium Carbonate, 2% Sodium Sulfate, 3% Sodium Nitrate, 0.1% Sodium Chlorate, 4 % Sampling. Samples requested by a Harnett County employee shall be taken by the driver at the point of delivery and in the presence of a Harnett County employee. The sample shall be placed in a container that will be provided by the County, which shall include a label to be completed by the driver collecting the sample. The sample shall be given to the Harnett County employee for processing Tank Samples. The sample taken by the driver should be a representative sample of the product delivered. Samples shall be held by County for 30 days before disposal Analysis. No independent analysis of the provided samples will be performed by an outside laboratory unless it is deemed necessary for product verification. A Harnett County employee supervising chemical delivery may perform simple tests such as specific gravity, ph or strength of product on the Page 17 of 40

18 product before it is accepted for offloading into the County s storage vessels. 1.7 Rejection Notice of Nonconformance. If the sodium chlorite delivered does not meet the requirements of ANSI/AWWA B standard, a notice of nonconformance shall be given to the supplier by County within ten days of County s discovery of nonconformance. County shall have the right to reject all nonconforming product Material Originating Outside of North America. No material shall be supplied under this contract that was manufactured outside of North America without written approval of the County. The supplier shall inform the County, in writing, that the material was manufactured outside of North America, the origin of the material, and certification of conformance with ANSI/AWWA B Standard. 1.8 Affidavit of Compliance The County requires (1) an affidavit from the manufacturer that the sodium chlorite furnished under these specifications complies with all applicable requirements of ANSI/AWWA B Standard. (2) A certified analysis of the sodium chlorite and a certified weight certificate shall be furnished by the supplier with each shipment. The analysis shall include product content Product Certifications. Sodium chlorite is a direct additive used in the treatment of potable water. This material should be certified as suitable for contact with or treatment of drinking water by an accredited certification organization in accordance with ANSI/NSF Standard 60, Drinking Water Treatment Chemicals - Health Effects. Evaluation shall be accomplished in accordance with requirements that are no less restrictive than those listed in ANSI/NSF Standard 60. Certification shall be accomplished by a certification organization accredited by the American National Standards Institute. 1.9 CHEMICAL SPILL RESPONSE REQUIREMENTS Hazmat Response Team. Each chemical supplier shall furnish the name, address and telephone number of a qualified Hazmat Response Team. This team shall be supplied by the supplier to clean-up and mitigate a chemical spill caused by the supplier or its designee. The Hazmat Response Team must meet OSHA requirements and be available twenty-four (24) hours per day, seven (7) days per week Spill Response. Response to a hazardous material clean-up shall occur within eight (8) hours of notification by the treatment plant or the authorized representative, Spill mitigation actions taken by PWD personnel shall not be construed as a replacement for Chemical Spill Response. The Water Resources Manager or authorized designee shall make the determination of need for Hazmat Response Team assistance. Supplier must supply information on response team prior to first shipment. 2.0 PACKAGING & SHIPPING Packaging and shipping of all sodium chlorite solutions shall conform to all applicable local, state and federal regulations (including USDOT regulations and applicable interstate regulations). Item No. 4 Sodium Chlorite continued on next page 2.1 Service & Maintenance Requirements Maintenance and Repair. The supplier shall provide all scheduled maintenance and repair of supplier-owned equipment as well as the County s chlorine dioxide generators. A service representative shall be on call and shall Page 18 of 40

19 respond within twenty four (24) hours after notification of an emergency situation (i.e., breakdown, repair or required service). The supplier shall ensure that the generator(s) and equipment is not out of service more than eight (8) hours at any one time during the period from April 1st thru October 31st of each year, or out of service more than fortyeight (48) hours at any other time Site Visits. The supplier shall conduct quarterly site visits (minimum) to provide the following (minimum): Check the operational modes of the generator(s) Check chlorine dioxide residuals Check the operational efficiency of the generator(s) Review plant operational records Provide a written service report to the Water Plant Supervisor Provide technical assistance, maintenance and calibration of component rotameters, pumps, solenoids, valves, vacuum system, etc Provide maintenance parts and components for the generator as required up to $ per site visit. The customer will be required to pay the total cost of the replacement parts that exceed $ Annual Efficiency Testing. The supplier will perform an annual on site efficiency test of the generators via a laboratory ampherometric instrument and provide a written report of the results, areas of deficiencies and the required steps to improve the generators operating efficiencies. Page 19 of 40

20 1.1 Scope ITEM NO. 5 LIQUID CHLORINE Liquid Chlorine supplied under this specification shall conform to all provisions of AWWA B Standard. This specification covers liquid chlorine for use in water treatment. The estimated annual usage is 30,000 pounds. Delivery will be in 150 pound cylinders and pricing is per pound chlorine. There will be no cylinder deposits or fees paid under this specification. 1.2 Purpose The purpose of this specification is to provide manufacturers and suppliers with the minimum requirements for liquid chlorine, including physical, chemical, packaging, shipping, and testing requirements. 1.3 Physical Requirements Liquid chlorine shall be amber colored and vaporize to a greenish-yellow gas. 1.4 Chemical Requirements The liquid chlorine supplied according to this standard shall be 99.5 percent pure by volume. 1.5 Impurities General. The liquid chlorine supplied according to this specification shall contain no soluble mineral or organic substances in quantities capable of producing deleterious effects on the health of those consuming water that has been treated properly with the sodium hypochlorite Specific Impurity Limits. Liquid chlorine shall contain no more than the following percentages of specific impurities by weight: Moisture, 0.015% Heavy Metals, % Lead, 0.001% Mercury, % Arsenic, % Total Residue, 0.015% Carbon Tetrachloride, 0.01 % Trihalomethanes, 0.03 % 1.6 Sampling and Analysis Sampling. If required by the County, samples will be taken at the point of shipment according to ASTM E410, ASTM E412and ASTM E806. Also see Chlorine Institute Pamphlet 77 on sampling chlorine Inspection. All containers shall be carefully examined by the supplier as discussed in Chlorine Institute Pamphlet 17 and in Compressed Gas Association Pamphlet C6, including proper holding of filled containers to check for leaks before filling. Any containers that show evidence of leakage, damage, or corrosion shall be rejected. Chlorine cylinders, valves, valve threads, and valve packings shall be in good mechanical order and shall operate normally with a wrench that is no longer than 8 in. (0.2 m). If the condition of the container and valves does not conform to any recommended practice in the above pamphlets in all applicable respects, the manufacturer or packager supplying the chlorine shall be notified immediately and shall take immediate action to ensure compliance. Routine inspection and cleaning of the interiors of chlorine cylinders shall be Page 20 of 40

21 1.7 Rejection performed by the supplier because of the potential buildup of contaminants when chlorine is removed as a gas Notice of Nonconformance. If the liquid chlorine delivered does not meet the requirements of ANSI/AWWA B standard, a notice of nonconformance shall be given to the supplier by County within ten days of County s discovery of nonconformance. County shall have the right to reject all nonconforming product Material Originating Outside of North America. No material shall be supplied under this contract that was manufactured outside of North America without written approval of the County. The supplier shall inform the County, in writing, that the material was manufactured outside of North America, the origin of the material, and certification of conformance with ANSI/AWWA B Standard. 1.8 Affidavit of Compliance The County requires (1) an affidavit from the manufacturer that the liquid chlorine furnished under these specifications complies with all applicable requirements of ANSI/AWWA B Standard. (2) A certified analysis of the liquid chlorine and a certified weight certificate shall be furnished by the supplier with each shipment. The analysis shall include product content Product Certifications. Liquid chlorine is a direct additive used in the treatment of potable water. This material should be certified as suitable for contact with or treatment of drinking water by an accredited certification organization in accordance with ANSI/NSF Standard 60, Drinking Water Treatment Chemicals - Health Effects. Evaluation shall be accomplished in accordance with requirements that are no less restrictive than those listed in ANSI/NSF Standard 60. Certification shall be accomplished by a certification organization accredited by the American National Standards Institute. 1.9 CHEMICAL SPILL RESPONSE REQUIREMENTS Hazmat Response Team. Each chemical supplier shall furnish the name, address and telephone number of a qualified Hazmat Response Team. This team shall be supplied by the supplier to clean-up and mitigate a chemical spill caused by the supplier or its designee. The Hazmat Response Team must meet OSHA requirements and be available twenty-four (24) hours per day, seven (7) days per week Spill Response. Response to a hazardous material clean-up shall occur within eight (8) hours of notification by the treatment plant or the authorized representative, Spill mitigation actions taken by PWD personnel shall not be construed as a replacement for Chemical Spill Response. The Water Resources Manager or authorized designee shall make the determination of need for Hazmat Response Team assistance. Supplier must supply information on response team prior to first shipment. 2.0 PACKAGING & SHIPPING Packaging and shipping of all liquid chlorine solutions shall conform to all applicable local, state and federal regulations (including USDOT regulations and applicable interstate regulations). Page 21 of 40

22 1.1 Scope ITEM NO. 6 a. SODIUM HYDROXIDE(50%) b. SODIUM HYDROXIDE (25%) Sodium hydroxide supplied for water plant use under this specification shall conform to all provisions of AWWA B Standard. This specification covers sodium hydroxide for use in water and wastewater treatment. The estimated annual usage is a.)150 dry tons (water plant) for full truck loads (TTL) and, b.) 26,000 gallons (wastewater plants) for less than truck loads (LTL). Sodium Hydroxide for the water plant shall be membrane grade. Sodium Hydroxide for the wastewater plants can be diaphragm grade. Pricing will be per dry ton. 1.2 Purpose The purpose of this specification is to provide manufacturers and suppliers with the minimum requirements for sodium hydroxide, including physical, chemical, packaging, shipping, and testing requirements. 1.3 Physical Requirements Liquid sodium hydroxide is a solution of anhydrous sodium hydroxide and water. 1.4 Chemical Requirements Sodium hydroxide delivered under this contract for the water plant shall contain approximately 50 percent sodium hydroxide (NaOH), sodium hydroxide for the wastewater plants may be either approximately 50 percent or approximately 25 percent as required by the County. 1.5 Impurities General. The sodium hydroxide supplied according to this specification shall contain no soluble material or organic substances in quantities capable of producing deleterious effects on the health of those consuming water that has been treated properly with the sodium hydroxide Specific Impurity Limits. Sodium hydroxide supplied to the water plant shall contain no more than the following percentages of specific impurities: Mercury 0.5 ppm Arsenic 1.5 ppm Lead 5 ppm Heavy Metals(as lead) 15 ppm Iron, % dry weight basis Sodium Chloride, 2.2% dry weight basis 1.6 Sampling and Analysis Sampling. Samples requested by a Harnett County employee shall be taken by the driver at the point of delivery and in the presence of a Harnett County employee. The sample shall be placed in a container that will be provided by the County, which shall include a label to be completed by the driver collecting the sample. The sample shall be given to the Harnett County employee for processing Tank Samples. The sample taken by the driver should be a representative sample of the product delivered. Samples shall be held by County for 30 days before disposal Analysis. No independent analysis of the provided samples will be performed by an outside laboratory unless it is deemed necessary for product verification. A Harnett County employee supervising chemical delivery may perform simple tests such as specific gravity, ph or strength of product on the Page 22 of 40