Enacted Dec 2007; Compliance date for Plan is Jan 22, How to keep your signs in good condition and yourselves out of court
|
|
- Letitia Allison
- 5 years ago
- Views:
Transcription
1 How to keep your signs in good condition and yourselves out of court Standard: Public agencies or officials having jurisdiction shall use an assessment or management method that is designed to maintain sign retroreflectivity at or above the minimum levels in Table 2A 3 Enacted Dec 2007; Compliance date for Plan is Jan 22, 2012 one or more of the following assessment or management methods should be used Visual Nighttime Inspection Calibration signs Comparison Panels Consistent parameters Measured Sign Retro Combination of Any Expected Sign Life Corridor Replacement Control Signs Future Method Based on Engineering Study Is the sign needed? Is the sign missing? Is the sign the correct one/ in compliance with MUTCD? Is the sign the correct size? Is the sign in the proper location Lateral clearance? Height above the edge of travel lane? Longitudinal placement along the road? Is the sign visible both day and night? If not, why Check the sign face Condition cracking, peeling Fading or discoloration Vandalism, graffiti, bullet holes Contrast Retroreflectivity Is the sign in the clear zone? If so, is the post yielding?
2 Municipality A maintains their signs by Nighttime Inspections and replacing any worn or damaged signs as they find them. Signs are replaced as needed and no schedule of replacements is needed. Municipality B maintains their signs by dividing their community into sections, and replacing all signs in a section each year. Every sign in the community is replaced within the expected life span of the sheeting used. When the first to be replaced are reaching the end of their life span, the cycle starts all over again. Municipality C maintains their signs by road or route, and has a schedule for which road has its signs replaced each year. Every sign in the community is replaced within the expected life span of the sheeting used, and then they start all over again. Municipality D replaces their signs by using the Expected Life of the type and color of sheeting used. They know when each sign was installed and what sheeting type it is, and when the sheeting manufacturer s guidelines say that the sheeting is about to fall below minimum retro levels, the sign is replaced. Parking/Standing/Stopping Walking/Hitchhiking Adopt A Highway Blue or Brown Backgrounds Exclusive Use of Bikes or Peds Support: Compliance with the Standard in par 02 is achieved by having a method to maintain the minimum levels established in Table 2A 3. Provided that a method is being used, an agency or official having jurisdiction would be in compliance even if there are some individual signs that do not meet the minimum levels at a particular point in time.
3 30 STOP Colors New MUTCD Table 2A.3 Which Sheeting is Allowable (Ground Mounted Only) Engineer Beaded Sheeting Super Eng. Hi- Intensity Prismatic Sheeting EG = $40 7 year warranty HI = $48 10 year warranty DG = $94 12 year warranty 2012 Pick a management method 2015 Warning, regulatory, & most guide signs 2018 Post mounted street signs VII VIII IX VII VIII IX CLRP is hiring an intern to assist municipalities in creating their sign management plans. Towns and Villages can also ask their County Highway Departments, and anyone can ask NYSDOT for help Regional offices for funding issues, my office for technical issues. I II III I II III Revisions to Chapter 2C Curve Warning Signs Fhwasa09025.pdf
4 Application of horizontal alignment signs based upon curve differential speed New criteria for the determination of advisory speeds Support: Among the established engineering practices that are appropriate for the determination of the recommended advisory speed for a horizontal curve are the following: A. An accelerometer that provides a direct determination of side friction factors B. A design speed equation C. A traditional ball-bank indicator criteria: 16 degrees of for speeds of 20 mph or less 14 degrees of for speeds of 25 to 30 mph 12 degrees of for speeds of 35 mph and more New variations of combination horizontal alignment- intersection warning signs Use of combination Turn/Advisory Speed sign, Curve/Advisory Speed sign Allowed ONLY as supplement to advance warning sign/advisory speed plaque assembly located at advance posting distance. If used, shall be located at the beginning of the turn or curve. New table for spacing of Chevron signs Chevron signs may be mounted at 4-foot 4 height Advisory Curve Sign Speed Radius Spacing (mph) (feet) (feet) 15 or less Less than to to to to to to 1, More than 60 More than 1,
5 Post mounted sign supports shall be crashworthy if within the clearzone (2A.19) A 3#/ft U-channel directly embedded is crashworthy A 2.25 square tube directly embedded is crashworthy When do you need an Engineer? Engineering JUDGMENT the evaluation of available pertinent information, and the application of appropriate principles, provisions, and practices as contained in this Manual and other sources, for the purpose of deciding upon the applicability, design, operation, or installation of a traffic control device. Engineering judgment shall be exercised by an engineer, or by an individual working under the supervision of an engineer, through the application of procedures and criteria established by the engineer. Documentation of engineering judgment is not required. Engineering STUDY the comprehensive analysis and evaluation of available pertinent information, and the application of appropriate principles, provisions, and practices as contained in this Manual and other sources, for the purpose of deciding upon the applicability, design, operation, or installation of a traffic control device. An engineering study shall be performed by an engineer, or by an individual working under the supervision of an engineer, through the application of procedures and criteria established by the engineer. An engineering study shall be documented. What requires a STUDY in the MUTCD?
6 DOCUMENTATION Where Why What How When Who When do you need an Engineer? MUTCD Q&A Textor 102 1:15-2:30 & 2:45-4:00
Sign Retroreflectivity Requirements in the MUTCD. Final Rule. MUTCD Changes. Conducting Visual Nighttime Inspections. University of Kentucky
Sign Retroreflectivity Requirements in the MUTCD Eric Green, MSCE, PE, GISP Kentucky Transportation Center Final Rule Published on Dec 21, 2007 Vol 72, No. 245 Revision #2 of the 2003 Edition of the MUTCD
More informationTraffic Solutions. MUTCD Compliance Dates & Systematic Upgrades. John Nisbet State Traffic Engineer. Lynn Peterson Secretary of Transportation
Traffic Solutions MUTCD Compliance Dates & Systematic Upgrades Rick Mowlds State Sign Engineer Lynn Peterson Secretary of Transportation John Nisbet State Traffic Engineer Road & Street Maintenance Supervisors
More informationSelecting a Method to Comply with the Requirements for Traffic Sign Retroreflectivity
Selecting a Method to Comply with the Requirements for Traffic Sign Retroreflectivity James W. Ellison, P.E. Consulting Traffic Engineer Federal Way, WA The Complexity of Sign Retroreflectivity Driver
More informationDEPARTMENT OF THE ARMY U.S. ARMY CORPS OF ENGINEERS 441 G STREET, NW WASHINGTON, DC
DEPARTMENT OF THE ARMY U.S. ARMY CORPS OF ENGINEERS 441 G STREET, NW WASHINGTON, DC 20314-1000 REPLY TO ATTENTION OF S: 30 September 2014 CECW-CO 3 0 December 20 11 MEMORANDUM FOR MSC and District Chiefs,
More information10/23/08. Sign reflectivity rule & the Private sector. Illinois Traffic Engineering & Safety Conference
Sign reflectivity rule & the Private sector Illinois Traffic Engineering & Safety Conference 10/23/08 Michael Conoscenti President 1740 Internationale Pkwy Woodridge, IL 60517 630-972-7770 x1011 mike@westernremac.com
More informationGreat Plains Waste Management Conference April 18, 2013 MUTCD MUTCD. Why Do We Install Signs? MUTCD
Great Plains Waste Management Conference April 18, 2013 Retroreflectivity Assessment and Management Methods Presented by Don Neary Nebraska LTAP Starting at age 20, the amount of light needed to see an
More informationPortable Changeable Message signs have a wide variety of
Part 6F (devices) Minnesota MUTCD 2005 with 2007 09 Revisions Part 6F (devices) Federal MUTCD 2009 Part 6F (devices) MN MUTCD Rearranged Sections 6F.55 Portable Changeable Message Signs Portable Changeable
More information90 th Annual T.H.E. Conference. Sign Retroreflectivity. Mike Staggs Mobility & Safety Team Leader Federal Highway Admin. - Ilinois
90 th Annual T.H.E. Conference Sign Retroreflectivity Mike Staggs Mobility & Safety Team Leader Federal Highway Admin. - Ilinois Overview Retroreflectivity What is it? Materials - How do retroreflective
More informationQUALITY STANDARDS for Temporary Traffic Control Devices
QUALITY STANDARDS for Temporary Traffic Control Devices Contents Introduction 1 Quality Requirements 2 Quality Standards 2 General 2 Barricades, Channelizing Devices, and Signs 3 Warning Lights 3 Flashing
More informationMobile Work Zones. Traffic Control in Short Duration / Guidelines for M0WING ZONE AHEAD WORK ROAD SHOULDER WORK RIGHT LANE CLOSED AHEAD SIGNAL AHEAD
M0WING ZONE ROAD WORK AHEAD SHOULDER WORK RIGHT LANE CLOSED AHEAD SIGNAL WORK AHEAD Guidelines for Traffic Control in Short Duration / Mobile Work Zones Guidelines for Traffic Control in Short Duration
More informationMEMORANDUM. ~ ~ //. -L/'j L!E.
~e* ~;~:~ent.,o.:-ransportation MEMORANDUM TO: All District Engineers DATE: September 28,2007 ~ ~ //. -L/'j L!E. FROIVI: Carlos A. Lopez, P.E. ~..t::o ce- V '1'~ r. SUBJECT: Revised Barricade and Construction
More informationCan You See The Signs? GIS Solutions for Sign Inventory & Retroreflectivity
Can You See The Signs? GIS Solutions for Sign Inventory & Retroreflectivity Jason Teisinger, M.A. 4/12/2017 Retroreflectivity Retroreflector A Device or Surface That Reflects Light Back to Its Source With
More informationWelcome!! Temporary Traffic Control During Maintenance and Short Duration Activities. Training Course 1-1
Welcome!! Temporary Traffic Control During Maintenance and Short Duration Activities Training Course 1-1 About This Course This material is based upon work supported by the Federal Highway Administration
More information2016 MUTCD CONCEPT TTC COMMENTS. Michael A. Chacon Traffic Operations Division
2016 MUTCD CONCEPT TTC COMMENTS Michael A. Chacon Traffic Operations Division MUTCD 4 Ballot items were discussed at the June 2014 meeting in TTC, as well as additional topics. TTC No. 1 Pedestrian and
More informationPart I. GENERAL PROVISIONS
Part I. GENERAL PROVISIONS 1A-1 Purpose of Traffic Control Devices The purpose of traffic control devices and warrants for their use is to help insure highway safety by providing for the orderly and predictable
More informationTRAFFIC ENGINEERING DIVISION INSTRUCTIONAL & INFORMATIONAL MEMORANDUM
VIRGINIA DEPARTMENT OF TRANSPORTATION TRAFFIC ENGINEERING DIVISION INSTRUCTIONAL & INFORMATIONAL MEMORANDUM GENERAL SUBJECT: Signs Lighting SPECIFIC SUBJECT: Overhead Sign Lighting DIRECTED TO: District
More informationQuality Standard for Work Zone Traffic Control Devices
Quality Standard for Work Zone Traffic Control Devices 2004 Introduction Traffic controls are a necessary part of highway work zones to warn motorists of hazards, advise them of the proper path through
More informationSection 13. Guidelines for the Design of Ground Mounted Sign Supports
Section 13 BDC11MR-04 13.1 Introduction Highway signs fall into two main categories, which are subdivided as follows: 1. Overhead Signs a. Sign Bridge Structures (GO) b. Sign Cantilever Structures (GO)
More informationCHAPTER 16: TRAFFIC. In either situation, the plan must contain the detail for the interim pavement markings.
CHAPTER 16: TRAFFIC ADVANCE WARNING SIGN SPACING The Advance Warning Sign Spacing for 0-30 mph has been reduced from 300 feet to 100 feet. This is more in line with the Federal MUTCD and accounts for more
More informationSPECIFICATIONS FOR TRAFFIC CONTROL SIGNS STREET MARKER BLADES SIGN POSTS MOUNTING BRACKETS AND INSTALLATION AT CUMMINGS RESEARCH PARK
SPECIFICATIONS FOR TRAFFIC CONTROL SIGNS STREET MARKER BLADES SIGN POSTS MOUNTING BRACKETS AND INSTALLATION AT CUMMINGS RESEARCH PARK I. GENERAL A. Cummings Research Park (CRP) Master Plan established
More informationCHAPTER ONE INTRODUCTION
5 CHAPTER ONE INTRODUCTION Pavement markings are an important means of communicating information to drivers. There are many differences in pavement marking practices among state and local transportation
More informationMONTEZUMA COUNTY COLORADO ROAD AND BRIDGE STANDARD SPECIFICATIONS
MONTEZUMA COUNTY COLORADO ROAD AND BRIDGE STANDARD SPECIFICATIONS The following Standard Specifications for Road and Bridge Construction in Montezuma County, Colorado have been amended this 22 nd, day
More informationNCUTCD Proposal for Changes to the Manual on Uniform Traffic Control Devices
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 TECHNICAL COMMITTEE: ITEM NUMBER: TOPIC: ORIGIN OF REQUEST: AFFECTED SECTIONS OF MUTCD: NCUTCD Proposal for
More informationPAVEMENT MARKINGS. F. Grooves Cut for Pavement Markings, Symbols, and Legends
PAVEMENT MARKINGS PART 1 - GENERAL 1.01 SECTION INCLUDES A. Permanent Pavement Markings, Symbols, and Legends B. Removable Pavement Markings, Symbols, and Legends C. Temporary Delineators D. Raised Pavement
More informationGENERAL NOTES FOR WORK ZONE SAFETY SET UP GUIDE
FORWARD It shall be the responsibility of the person in charge to institute the placing of all appropriate cautionary devices and controls as may be required for the particular job. Traffic protection
More informationField Guide on. Safe Maintenance and. Work Zone Operations
Field Guide on Installation and Removal of Temporary Traffic Control for Safe Maintenance and Work Zone Operations August 2008 Introduction This field guide provides field personnel with introductory guidance
More informationImportance of Pavement Marking Retroreflectivity Standards
Importance of Pavement Marking Retroreflectivity Standards Paul Carlson, Ph.D., P.E. Research Engineer Texas A&M Transportation Institute Texas A&M University TTI s Visibility Research Laboratory Research
More informationDoor County Uniform Addressing Manual
Door County Uniform Addressing Manual Purposes of Manual 1) To supplement Door County Ordinance No. 02-00, Uniform Addressing System. 2) To establish the procedures used to implement and administer a uniform
More informationMODULE 10 Road Ranger Work Zones
MODULE 10 Road Ranger Work Zones Module 10 1 Purpose of the Course To train personnel who may be required to assist motorists and emergency personnel within the highway right-of-way, as part of their Road
More informationTemporary Traffic Control Design Specialist. Training Course
Temporary Traffic Control Design Specialist Training Course About This Course This material is based upon work supported by the Federal Highway Administration (FHWA) under grant agreement No. DTFH61-06-G-00004
More informationIowa Prison Industries
Iowa Prison Industries Iowa Municipal Finance Officers Association Agenda About IPI IPI s products and services and the skills learned in their production Iowa DOT s sign retro-reflectivity standards Iowa
More informationTABLE OF CONTENTS. Manual Section. Introduction 1. Using This Manual 2-3. Administrative Actions 4-6. Road and Bridge Project Types 7
ii TABLE OF CONTENTS Manual Section Pages Introduction 1 Using This Manual 2-3 Administrative Actions 4-6 Road and Bridge Project Types 7 Road and Bridge Funding Programs 8-9 Project Planning and Eligible
More informationCITY OF FARGO SPECIFICATIONS SIGNING
SIGNING PART 1 DESCRIPTION OF WORK The work to be done under this section of the Specifications and the accompanying plans consists of furnishing all labor, material and accessories necessary to complete
More informationTRB Webinar: Maintenance Practices for Traffic Sign Retroreflectivity
TRB Webinar: Maintenance Practices for Traffic Sign Retroreflectivity Today s Presenters and Moderator Paul Carlson, Texas Transportation Institute at Texas A&M University, Paul-Carlson@tamu.edu Jim Ellison,
More informationCITY OF FARGO SPECIFICATIONS SIGNING
SECTION 4300 SIGNING PART 1 DESCRIPTION OF WORK The work to be done under this section of the Specifications and the accompanying plans consists of furnishing all labor, material and accessories necessary
More informationGEOMETRIC DESIGN CRITERIA for Non-freeway Resurfacing, Restoration, and Rehabilitation Projects
GEOMETRIC DESIGN CRITERIA for Non-freeway Resurfacing, Restoration, and Rehabilitation Projects SEPTEMBER 1989 Arkansas State Highway and Transportation Department GEOMETRIC DESIGN CRITERIA for Non-freeway
More informationQuality Standards. for Temporary Traffic Control Devices OKLAHOMA DEPARTMENT OF TRANSPORTATON
Quality Standards for Temporary Traffic Control Devices OKLAHOMA DEPARTMENT OF TRANSPORTATON April 2009 Introduction Temporary traffic control devices (TCD) are a necessary part of highway work zones.
More informationAPPLICATION SPECIFICATION CONVENTIONAL PAVEMENT MARKING MATERIALS 3 MINUTE DRY ALKYD AND HIGH SOLIDS LATEX
APPLICATION SPECIFICATION CONVENTIONAL PAVEMENT MARKING MATERIALS 3 MINUTE DRY ALKYD AND HIGH SOLIDS LATEX Values stated in the International System of Units SI apply only to projects to be constructed
More informationLOCATION AND DESIGN DIVISION
VIRGINIA DEPARTMENT OF TRANSPORTATION LOCATION AND DESIGN DIVISION INSTRUCTIONAL AND INFORMATIONAL MEMORANDUM GENERAL SUBJECT: Design Exceptions / Waivers SPECIFIC SUBJECT: Design Exception Request Form
More informationWork Zone Inspection Process
Work Zone Inspection Process 2013 Louisiana Transportation Conference Barry L. Lacy, P.E. Work Zone/Claims/Audit Engineer Louisiana State Motto Why is Temporary Traffic Control Important? www.workzonesafety.org
More informationNew Jersey Turnpike Authority
New Jersey Turnpike Authority DOCUMENT UPDATE REQUEST Forward to Assistant Chief Engineer, Design Initiator Russell Saputo, PE Submittal Date 6/21/16 Firm Stantec Consulting Services Inc. Telephone 201-587-9040
More informationWelcome!! Traffic Control Supervisor. Training Course
Welcome!! Traffic Control Supervisor Training Course Traffic Control Supervisor Training Course Two-day course Begins promptly at 8:00 AM Ends no later than 5:00 PM Flexible schedule!! 0-2 Course Objectives
More informationAASHTO S NATIONAL TRANSPORTATION PRODUCT EVALUATION PROGRAM (NTPEP)
AASHTO S NATIONAL TRANSPORTATION PRODUCT EVALUATION PROGRAM (NTPEP) TEMPORARY TRAFFIC CONTROL DEVICES DATA USAGE GUIDE INRODUCTION The NTPEP program has successfully supplied material performance data
More informationNYSDOT TRANSPORTATION MAINTENANCE DIVISION PAVING PROJECT QUALITY ASSURANCE ASSESSMENT Rating Guidelines (Revision #1)
NYSDOT TRANSPORTATION MAINTENANCE DIVISION PAVING PROJECT QUALITY ASSURANCE ASSESSMENT Rating Guidelines (Revision #1) INTRODUCTION The condition assessment is intended to be performed from a customer
More information805 - WORK ZONE TRAFFIC CONTROL & SAFETY SECTION 805 WORK ZONE TRAFFIC CONTROL AND SAFETY
SECTION 805 WORK ZONE TRAFFIC CONTROL AND SAFETY 805.1 DESCRIPTION Provide, erect, maintain and remove traffic control devices as shown in the Contract Documents. On roadways that carry traffic through
More informationAssessment of Sign Retroreflectivity Compliance for Development of a Management Plan
Assessment of Sign Retroreflectivity Compliance for Development of a Management Plan Travis Evans, Kevin Heaslip, Wesley Boggs, David Hurwitz, and Kevin Gardiner The Manual on Uniform Traffic Control Devices
More informationDraft. Not yet Approved
2016 Part 3.2.5 Recommended Design Criteria and Functional/Operating Guidelines for Overhead Bridge and Cantilever Structures and Placement of Grade Crossing Warning Devices Revised 2017 (8 Pages) A. Purpose
More informationMOBILE FOOD VENDOR LICENSE APPLICATION
MOBILE FOOD VENDOR LICENSE APPLICATION BUSINESS NAME AS DISPLAYED ON THE VEHICLE OR CART: Write the name and address of the location where the food truck/cart is kept overnight: APPLICANT INFORMATION:
More informationAMENDMENTS Manual of STANDARD SPECIFICATIONS. Adopted by Standard Specifications Committee. Amendment. No. 7. Published by
AMENDMENTS to 2012 Manual of STANDARD SPECIFICATIONS Adopted by Standard Specifications Committee Amendment No. 7 Published by Utah LTAP Center Utah State University 8305 Old Main Hill Logan UT 84322-8205
More informationOKLAHOMA TURNPIKE AUTHORITY SPECIAL PROVISION FOR SECTION 880 CONSTRUCTION SIGNING AND TRAFFIC CONTROL
OKLAHOMA TURNPIKE AUTHORITY SPECIAL PROVISION FOR SECTION 880 These Special Provisions revise, amend, and where in conflict, supercede applicable Sections of the Standard Specifications for Turnpike Construction,
More informationKANSAS DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION TO THE STANDARD SPECIFICATIONS, 1990 EDITION
KANSAS DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION TO THE STANDARD SPECIFICATIONS, 1990 EDITION Sheet 1 of 7 NOTE: This special provision is generally written in the imperative mood. The subject, the
More informationDIVISION I TRAFFIC IMPACT STUDY GUIDELINES ENGINEERING STANDARDS
CITY OF ALBANY DEPARTMENT OF PUBLIC WORKS DIVISION I TRAFFIC IMPACT STUDY GUIDELINES ENGINEERING STANDARDS Prepared By PUBLIC WORKS DEPARTMENT ALBANY, OREGON 97321 Telephone: (541) 917-7676 TABLE OF CONTENTS
More informationQ18-06 REQUEST FOR PROPOSALS REPAINT EPOXY PAVEMENT MARKINGS ON S. MAIN STREET. RFP Issuance Date: April 17, 2018 Proposal Due Date: May 8, 2018
Q18-06 REQUEST FOR PROPOSALS REPAINT EPOXY PAVEMENT MARKINGS ON S. MAIN STREET Engineering Department RFP Issuance Date: April 17, 2018 Proposal Due Date: May 8, 2018 The City of West Bend (City) is requesting
More informationStudent Services & Classroom Addition
SECTION 321723 - PAVEMENT MARKINGS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationBEST PRACTICES FOR WORK ZONE TRAFFIC CONTROL ON HIGHWAYS, STREETS AND BRIDGES
BEST PRACTICES FOR WORK ZONE TRAFFIC CONTROL ON HIGHWAYS, STREETS AND BRIDGES Developed by: The Dallas Area Road Construction Work Zone Task Force WORK ZONE TRAFFIC CONTROL BEST PRACTICES I Management
More informationMEDIAN OPENINGS AND ACCESS MANAGEMENT
Approved: Effective: February 20, 2013 Office: Systems Planning Topic No.: 625-010-021-h Department of Transportation PURPOSE: MEDIAN OPENINGS AND ACCESS MANAGEMENT This procedure provides direction on
More informationSpecial Specification 6148 Inverted Profile Pavement Marking (Audible)
Special Specification Inverted Profile Pavement Marking (Audible) 1. DESCRIPTION 2. MATERIALS Furnish and install an Inverted Profile Pavement Marking (Audible) that is hot applied to the pavement surface.
More informationSPECIFICATION FOR NOISE MITIGATION
SPECIFICATION FOR NOISE MITIGATION 1. SCOPE This specification covers the design, construction, documentation and postconstruction review of state highway road-traffic noise mitigation. This specification
More informationVillage of Glendale Quiet Zone Evaluation. Final Report Presented by: Railroad Controls, LP March, 2007
Village of Glendale Quiet Zone Evaluation Final Report Presented by: Railroad Controls, LP Sharon Road Albion Avenue Oak Street Quiet Zone Evaluation Village of Glendale, OH Introduction The Village of
More informationTable of Contents TOC. General Information. Street Classifications. Geometric Design Criteria
Design Manual Chapter 5 - Roadway Design Table of Contents TOC Table of Contents Chapter 5 - Roadway Design 5A General Information 5A-1---------------------------------General Information A. Concept.....
More informationASSEMBLY, No STATE OF NEW JERSEY. 218th LEGISLATURE PRE-FILED FOR INTRODUCTION IN THE 2018 SESSION
ASSEMBLY, No. STATE OF NEW JERSEY th LEGISLATURE PRE-FILED FOR INTRODUCTION IN THE 0 SESSION Sponsored by: Assemblywoman ELIANA PINTOR MARIN District (Essex) SYNOPSIS Port Support Zone Act of 0. CURRENT
More informationMay 2004 Traffic Control 600-i. Table of Contents 601 WORK ZONE TRAFFIC CONTROL DESCRIPTION OF WORK
DIVISION 600 Traffic Control SOUTH CAROLINA DEPARTMENT OF TRANSPORTATION May 2004 May 2004 Traffic Control 600-i Section Table of Contents Page 601 WORK ZONE TRAFFIC CONTROL...601-1 601.1 DESCRIPTION
More informationOKLAHOMA DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR PAVEMENT AND BRIDGE DECK SMOOTHNESS
430-2QA(a-i) 09 OKLAHOMA DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR PAVEMENT AND BRIDGE DECK SMOOTHNESS These Special Provisions amend and where in conflict, supersede applicable sections of the
More informationBetween existing Interstate 70 in St. Louis, MO to west of the IL 203 Interchange on existing I-55/70 in Madison, IL
American Association of State Highway and Transportation Officials An Application from the State Highway or Transportation Department of Illinois for: Elimination of a U.S. (Interstate) Route Establishment
More informationCommonwealth of Pennsylvania Department of Transportation SPECIFICATION FOR PLASTIC SIGNS. January 25, 2008
Commonwealth of Pennsylvania Department of Transportation SPECIFICATION FOR PLASTIC SIGNS January 25, 2008 1. SCOPE This specification covers folding plastic traffic signs and plaques for use within maintenance
More informationSECTION 6. ROAD CONSTRUCTION STANDARDS
SECTION 6. ROAD CONSTRUCTION STANDARDS Construction of new roads or reconstruction of existing roads proposed for dedication to the County shall conform to the standards set forth in this section. Roads
More informationTRAFFIC CONTROL STANDARDS
SIGNALS, SIGNS & SPEED THE STATE ROLE TRAFFIC CONTROL STANDARDS 2 Ohio Township Conference 1 TCD STANDARDS o The Rule book for traffic control devices is the Ohio Manual of Uniform Traffic Control Devices
More informationTHE SASKATCHEWAN CODES OF PRACTICE GAS INSTALLATION SUPPLEMENT CSA-B PROPANE STORAGE AND HANDLING CODE
THE SASKATCHEWAN CODES OF PRACTICE GAS INSTALLATION SUPPLEMENT CSA-B149.2-15 PROPANE STORAGE AND HANDLING CODE Revision Date: CONTENTS The following clauses have been amended, noted, explained or added
More informationSTREET IMPROVEMENTS (Refer to Title 18, chapter entitled "STREETS" of the Layton Municipal Code.)
STREET IMPROVEMENTS (Refer to Title 18, chapter 18.24 entitled "STREETS" of the Layton Municipal Code.) I. Street widths STREET TYPE (ALL MEASUREMENTS IN FEET) ROW WIDTH LAYTON CITY STANDARD STREET SECTIONS
More informationRoadway Surfaces and Traffic Control Elements
Roadway Surfaces and Traffic Control Elements Lines of Business: General Liability, Public Officials Liability www.tridentinsurance.net Risk Control Strategy/Key Issues: To establish and document a program
More informationHennepin County Transportation Department ADDENDUM
Hennepin County Transportation Department ADDENDUM TO PLANS, SPECIFICATIONS AND SPECIAL PROVISIONS FOR CSAH 5 INTERSECTION IMPROVEMENTS HENNEPIN COUNTY TRANSPORTATION DEPARTMENT (To be opened Tuesday,
More informationCHAPTER 7 ROADWAY STANDARDS AND TECHNICAL CRITERIA
Table of Contents CHAPTER 7 ROADWAY STANDARDS AND TECHNICAL CRITERIA Table of Contents 7-01 ROADWAY DESIGN AND TECHNICAL CRITERIA...1 7-01-01 General...1 7-01-02 Required Design Submittals...2 7-01-03
More informationDepartment of Building and Zoning Approaches and Sidewalks for ONE AND TWO FAMILY CONSTRUCTION
Department of Building and Zoning Approaches and Sidewalks for ONE AND TWO FAMILY CONSTRUCTION GENERAL ITEMS SUBGRADE Prior to pouring concrete all subgrades must be wetted and compacted. All formwork
More informationSPECIAL SPECIFICATION 8625 All-Weather Traffic Markings
2004 Specifications CSJ 6203-45-001, 6225-40-001 & 0045-02-031 SPECIAL SPECIFICATION 8625 All-Weather Traffic Markings 1. Description. This work will consist of furnishing and installing a wet reflective
More informationSECTION 616 TEMPORARY TRAFFIC CONTROL
SECTION 616 TEMPORARY TRAFFIC CONTROL 616.1 Description. This work shall consist of furnishing, installing, operating, maintaining, cleaning, relocating and removing temporary traffic control devices and
More informationEvaluation of Sign Sheeting Service Life in Wyoming
PAPER #-0 Evaluation of Sign Sheeting Service Life in Wyoming by Adam M. Pike, P.E. (Corresponding Author) Assistant Research Engineer Signs and Marking Program Texas A&M Transportation Institute TAMU
More information53.20 PAINTED ROADWAY LINES
53.20 PAINTED ROADWAY LINES 53.20.1 GENERAL The Work consists of supplying paint and painting roadwaylines on pavement surfaces. The various configurations of roadway lines are shown on drawing TEB 2.25.
More informationDMS-8300, Flat Surface Reflective Sheeting
Overview Effective Date: February 2003 April 2003. This specification governs for the materials, composition, quality, sampling, and testing of five (5) types of flat-surface, reflective sheeting. Type
More informationCITY OF LA QUINTA GENERAL NOTES GENERAL NOTES
CITY OF LA QUINTA GENERAL NOTES GENERAL NOTES 1. ALL WORK SHALL BE DONE IN ACCORDANCE WITH THE LATEST EDITION OF THE STANDARD PLANS OF THE CITY OF LA QUINTA, THE LATEST EDITION OF THE STANDARD SPECIFICATIONS
More informationFading of Fluorescent Yellow Signs
Version 2/15/2017 TITLE OF PROJECT: IMPLEMENTATION PLAN AND PROJECT PROPOSAL PROJECT PROPOSED BY: Josie Tayse Fading of Fluorescent Yellow Signs LRRB INV #: SP&R #: ARTS Project #: Page 1 of 7 POSITION
More informationSTANDARD SHELTER SPECIFICATIONS ATTACHMENT A
STANDARD SHELTER SPECIFICATIONS 16-04 ATTACHMENT A Issued: November 2, 2015 Technical Specifications ---------------------------------------------------------------------------------------------------------------
More informationJ&C Construction Agency
Traffic Control Inspection conducted for J&C Construction Agency Date and Time of Inspection 04 May 2018 06:57 AM Project Number JCCA-1234 Competent Person Steeve Rogerson Inspected by SafetyCulture Staff
More informationSECTION PORTLAND CEMENT CONCRETE
PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including the supplemental documents as indicated in the Site Work General Provisions, apply to work of this
More information805 - WORK ZONE TRAFFIC CONTROL & SAFETY SECTION 805 WORK ZONE TRAFFIC CONTROL AND SAFETY
SECTION 805 WORK ZONE TRAFFIC CONTROL AND SAFETY 805.1 DESCRIPTION Provide, erect, maintain and remove traffic control devices as shown in the Contract Documents. BID ITEMS UNITS Work Zone Signs (0 to
More informationKANSAS DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION TO THE STANDARD SPECIFICATIONS, 1990 EDITION
Sheet 1 of 7 KANSAS DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION TO THE STANDARD SPECIFICATIONS, 1990 EDITION SECTION TRAFFIC CONTROL Page 628, subsection.01. Delete the following bid items: Advance
More information5.0 Plan Development. 5.1 Introduction. 5.2 Design References
5.0 Plan Development 5.1 Introduction The plan development section of this manual is intended to assist the LPA and the designer through the preliminary engineering phase of project development. Information
More informationSUBDIVISION SECTION STREET DESIGN MANUAL
CITY OF ANAHEIM SUBDIVISION SECTION STREET DESIGN MANUAL A. INTRODUCTION : POLICY STATEMENT B. STREET CLASSIFICATION C. STREET STANDARDS REQUIREMENTS Requirements Approval of Street Improvement Plans Widening
More informationDOWNTOWN OXNARD PARKLET PILOT PROGRAM PARKLET DESIGN GUIDELINES
Development Services Planning Division 214 South C Street Oxnard, California 93030 (805) 385-7858 Fax (805) 385-7417 DOWNTOWN OXNARD PARKLET PILOT PROGRAM PARKLET DESIGN GUIDELINES I. INTRODUCTION As part
More informationFLORIDA DEPARTMENT OF TRANSPORTATION
FLORIDA DEPARTMENT OF TRANSPORTATION ADDENDUM NO. 2 DATE: December 28, 2011 RE: RFP NUMBER: RFP TITLE: ITS Equipment Replacement in Broward County OPENING OF TECHNICAL PROPOSAL DATE: January 5, 2012 Notice
More informationTender No. [ ] Page 1
Tender No. [ ] Page 1 1.0 GENERAL 1.1 TRAFFIC ACCOMMODATION STRATEGY.1 Provide a Traffic Accommodation Strategy detailing the measures proposed to safely accommodate the travelling public. The minimum
More informationChapter 8 WORK ZONE TRAFFIC CONTROLS
October 31, 2009 Chapter 8 WORK ZONE TRAFFIC CONTROLS TABLE OF CONTENTS Page 8-1.00 INTRODUCTION..........................................................8-3 1.01 Purpose 1.02 Scope 1.03 Relation to Other
More informationMUTCD Part 6F: Temporary Traffic Control Zone Devices
MUTCD Part 6F: Temporary Traffic Control Zone Devices 6F.01 Types of Devices FHWA policy requires that all roadside appurtenances such as traffic barriers, barrier terminals and crash cushions, bridge
More informationKANSAS DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION TO THE STANDARD SPECIFICATIONS, 1990 EDITION
Sheet 1 of 6 KANSAS DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION TO THE STANDARD SPECIFICATIONS, 1990 EDITION SECTION TRAFFIC CONTROL Page 628, subsection.01. Delete the following bid items: Advance
More informationB STEEL BEAM GUIDE RAIL - OPSS 721
B721-2 - - OPSS 721 721-2.1 GENERAL Design guidance and a description of Steel Beam Guide Rail systems, including various types and treatments, are provided in the Roadside Design Manual (RDM). 721-2.2
More informationACRP Report 52. Available since late 2011 Download from TRB web site Provide airport operators updated resource on wayfinding and signing guidelines
Available since late 2011 Download from TRB web site Provide airport operators updated resource on wayfinding and signing guidelines 1 Panel Broward County Aviation Dept. Port of Oakland Massachusetts
More informationTraffic standards and guidelines 2001/2002 survey. RSS 19 Traffic signs. March 2003 ISSN ISBN
Traffic standards and guidelines 2001/2002 survey RSS 19 Traffic signs March 2003 ISSN 1174 7161 ISBN 0 478 241445 Survey of traffic standards and guidelines The Land Transport Safety Authority (LTSA)
More informationCITY UTILITIES DESIGN STANDARDS MANUAL
CITY UTILITIES DESIGN STANDARDS MANUAL Book 2 (SW) SW7 September 2017 SW7.01 Purpose The purpose of this Chapter is to establish a basis for inlet design utilizing City of Fort Wayne standard inlets and
More informationCONSTRUCTION SPECIFICATION FOR PAVEMENT MARKING
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 710 NOVEMBER 2010 CONSTRUCTION SPECIFICATION FOR PAVEMENT MARKING TABLE OF CONTENTS 710.01 SCOPE 710.02 REFERENCES 710.03 DEFINITIONS 710.04 DESIGN
More informationCONSTRUCTION SPECIFICATION FOR PAVEMENT MARKING
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 532 JUNE 1991 CONSTRUCTION SPECIFICATION FOR PAVEMENT MARKING 532.01 SCOPE 532.02 REFERENCES 532.03 DEFINITIONS TABLE OF CONTENTS 532.04 SUBMISSION
More informationTEST REPORT. Lucideon Reference: (QT-49195/1/GMB)/Ref. 1. Testing of OnLevel TL6020 Balustrade System in Accordance with BS 6180:2011
TEST REPORT Lucideon Reference: 18125 (QT-49195/1/GMB)/Ref. 1 101 Project Title: Client: For the Attention of: Author(s): Testing of OnLevel TL6020 Balustrade System in Accordance with BS 6180:2011 OnLevel
More information