MOA Project # Golden View Drive Intersection & Safety Upgrades

Size: px

Start display at page:

Download "MOA Project # Golden View Drive Intersection & Safety Upgrades"

Peregrine Davidson
6 years ago
Views:

1 Appropriate transitions can include extending the insulation beyond the roadway improvements, reducing the insulation thickness, or angling the insulation downward. Use of a frost tolerant section, an alternative to the insulated section, may be warranted where subgrade soil has low to moderate frost susceptibility or where groundwater is relatively deep and subgrade soil is not saturated most of the year. A frost tolerant section could be considered at the beginning of the project, from approximate station to about station Soil borings in this area encountered shallow weathered rock, between 2.5 feet to 12 feet below ground surface. A frost tolerant section may also be considered at the north end of the project, between approximate stations to General appearance of the pavement surface suggests that roadway performance in this segment is better than the remainder of the alignment. A frost tolerant section in these two segments would consist of approximately 2.25 feet of NFS fill material. For both an insulated and frost tolerant section, a non-woven geotextile is included along the base of the structural section to separate the native silty subgrade materials from the imported subbase fill. When peat is exposed in the base of the excavation, it is recommended that the peat be excavated out and replaced with imported fill. H. Retaining Walls Due to the steep adjacent terrain along the project corridor, retaining walls will be required to reduce the impacts from roadway grading and slopes. Retaining walls should be installed as needed to minimize impacts to utilities, the environment, and adjacent properties. 1. Retaining Wall Types Below is a description of the four basic types of retaining walls along with their characteristics. March

Gravity: Gravity retaining walls rely on the mass of the wall structure for stability. The wall mass must be sufficient to counteract sliding and overturning forces from the retained soil.

These are the most common type of retaining walls and include gabions, bin walls, and Example rock-gabion retaining wall Example modular block retaining wall modular block concrete construction.

2 Gravity: Gravity retaining walls rely on the mass of the wall structure for stability. The wall mass must be sufficient to counteract sliding and overturning forces from the retained soil. These systems can use stone, concrete or other heavy material as well as mechanically stabilized earth (MSE) for stability. These are the most common type of retaining walls and include gabions, bin walls, and Example rock-gabion retaining wall Example modular block retaining wall modular block concrete construction. In most cases the slope behind the wall needs to be temporarily removed during construction. For mechanically stabilized earth walls, the reinforcing often extends horizontally into the embankment about as far as the exposed wall face is tall. Piling: Piling retaining walls have structures that extend significantly below grade to provide support to counteract horizontal forces from the retained soils. Typically two thirds of the structure height is embedded below grade. The structures are usually steel sheet piles or H beams. Piles are driven into the soil while H beams can either be driven in or set into drilled holes. Quite often, the structural face of a piling wall is covered with a facade of concrete blocks or panels. These are some of the most expensive types of retaining walls but they do allow construction with very little removal of soil behind the wall. Cantilever: Cantilever retaining walls have a large effective mass due to the soil placed over a horizontal section of the wall. These walls are typically constructed of cast-in-place, reinforced concrete. The horizontal (cantilevered) leg of the March

3 structure can either extend back into the retained soil or out away from the slope. The slope behind the wall typically needs to be temporarily removed during construction. Cantilever walls are relatively expensive due to the work required to build concrete forms, install reinforcing, pour concrete, and provide joints between pours. The concrete needs ample time to cure before the soil can be replaced behind the wall. Basic types of retaining walls Anchored: Anchored (or tieback) retaining walls use cables driven horizontally into the soil to counteract opposing horizontal forces from the retained soils. The anchors, which typically pull horizontal plates or sheets against the soil, can be soil nails, tieback cables, or screw anchors. The soil behind the wall does not need to be removed during construction. The anchors may need to extend into March

4 the embankment quite a ways, which can impact buried utilities or future development. Combination: Many retaining walls use a combination of the above types. For example, many piling walls use anchors to reduce embedment depth and structure strength. 2. Considerations Below are important considerations that affect the decision to provide a retaining wall and which type of wall should be constructed. The decision to construct a retaining wall can be subjective and must balance the cost of installing a retaining wall with the overall impacts to utilities, wetlands, the environment, or adjacent properties. Impacts to wetlands often demand construction of retaining walls due to permitting requirements to avoid or minimize wetlands impacts if possible. Exact locations of retaining walls will require further refinement during the design phase. Embankment Impacts: Gravity and cantilever retaining walls typically require some of the soil behind the wall to be temporarily removed during construction. In some cases the slope can be cut to stand near vertical for short periods of time to reduce impacts but OSHA embankment guidelines and worker safety must be accounted for. Piling walls can minimize impacts to adjacent properties and structures. Foundation Soils: Gravity and cantilever retaining walls require a solid foundation to resist the forces of the wall and soil. Where foundation soils are weak, a piling or anchor wall should be considered or the weak soil replaced. The bedrock encountered near the south end of the Golden View Drive project provides an excellent foundation but makes driving sheet piles very difficult (see APPENDIX E for the geotechnical report). Groundwater/Drainage: Groundwater needs to be removed from behind the retaining wall to reduce hydrostatic forces. Many types of wall are inherently porous while other types, like reinforced concrete, require weep holes to be integrated into the design to relieve pressure from water behind the wall. In areas where substantial groundwater and glaciation is expected, a subdrain should be March

considered to direct the runoff to drainage ditches or a piped storm drain collection system. Utilities: Some types of retaining walls impact a considerable amount of soil behind the face of the wall.

5 considered to direct the runoff to drainage ditches or a piped storm drain collection system. Utilities: Some types of retaining walls impact a considerable amount of soil behind the face of the wall. For example, modular block walls and MSE walls rely on reinforcing geotextile fabric embedded into the soil as part of the structure. The fabric behind the wall can impact existing utilities or limit future placement of utilities. Anchor wall cables also extend into surrounding soils and affect utilities. Aesthetics: Retailing walls are often very noticeable along a roadway corridor and they should be selected to compliment the landscaping design and blend in with the surrounding neighborhood. Sometimes retaining walls are chosen to match existing walls on adjacent properties. Many of the existing retaining walls along Golden View Drive are large irregular boulders. Although many PM&E roadway project use concrete modular block retaining walls, gabion walls may be more appropriate for this project area where residents have expressed a desire to retain the rural feel. Gabion walls have also been used in other Anchorage hillside areas including along Birch Road and for South Anchorage High School. Safety Fence or Handrail: When the vertical face of the retaining wall is more than 2.5 feet tall, a fence, handrail, or guardrail should be provided for safety. Moose should be discouraged from walking over the wall. Where space is limited, a fence or handrail can be placed near the face of a reinforced concrete wall. Most other types of wall require the fence to be set back in the soil behind the wall. March

Construction Schedule: In some cases, the amount of time required to construct a retaining wall is very important since it can affect impacts to adjacent property owners or the

They are typically not a good option for stream culvert headwalls that need to be completed quickly to reduce environmental impacts.

6 Construction Schedule: In some cases, the amount of time required to construct a retaining wall is very important since it can affect impacts to adjacent property owners or the environment. Reinforced concrete headwalls take a considerable amount of time to construct. They are typically not a good option for stream culvert headwalls that need to be completed quickly to reduce environmental impacts. Construction of gabion-type retaining wall Maintenance: Retaining walls and associated fences or handrails should be designed to require little if any maintenance. Concrete surfaces can be provided with coatings to facilitate removal of spray paint vandalism. Construction of modular block retaining wall March

Cost: The estimated installed cost for retaining walls varies considerably from $45 to more than $200 per square foot of the exposed vertical face.

7 Cost: The estimated installed cost for retaining walls varies considerably from $45 to more than $200 per square foot of the exposed vertical face. Some of the biggest factors include soil conditions, wall height, tiebacks, construction Example modular block retaining wall with railing access, type of fence and the amount of soil to be removed behind the wall for construction. Below is a summary of order-of-magnitude cost for various types of retaining walls for comparison purposes. These costs include a chain link fence above the wall. Retaining Wall Type Modular block (Keystone), without tiebacks Modular block (Keystone), geogrid tiebacks Summary of Unit Costs Cost per Square foot of Excavation wall face, installed full excavation behind blocks, $45 limited to 4' height $60 full excavation behind geogrid Mechanically Stabilized Earth (MSE) $75 with concrete face, full excavation behind wall and tieback Gabion Basket $75 full excavation behind wall Reinforced concrete, cast-in-place Soldier pile, without tiebacks $120 $130 full excavation behind base of structure with block facade, minimal excavation behind wall Soldier pile, with tiebacks $190 Sheet pile, without tiebacks $180 Sheet pile, with tiebacks $210 with block facade, minimal excavation behind wall with block facade, no excavation behind wall with block facade, no excavation behind wall March

8 3. Estimated Project Cost The conceptual drawings located in APPENDIX B indicate where retaining walls should be considered to limit impacts to utilities, the environment or adjacent property. The potential areas for retaining walls for the preferred alternative (Alternative 1) are summarized below in TABLE 7. Note: this summary does not include stream culvert headwalls. Street Table 7 Summary of Retaining Walls (preferred alternative) Approx. Start Station Ave Height (ft) Length (ft) Area (sf) Utility Purpose Offset Environment Property Golden View Left X Golden View Right X X Golden View Right X Golden View Right ,824 X X Golden View Left X Golden View Left X Golden View Left X Golden View Right ,668 X X Golden View Right X Golden View Left ,002 X X Golden View Left ,355 X Golden View Left ,385 X Romania Left X A modular block or gabion basket type retaining wall can be used in nearly all of the areas identified above. Assuming a unit cost from $60 to $75 for modular block and gabion basket wall types respectively, this represents an approximate cost of $880 thousand to $1.01 million for the recommended Alternative 1. I. Traffic Calming Based on speed studies and comments from local residents, speeding is a concern. Various methods for traffic calming were investigated, including: Vertical traffic calming measures (ex. speed hump) Horizontal traffic calming measures (ex. neckdowns) March

CHAPTER 11: WALLS.

CHAPTER 11: WALLS. CHAPTER 11: WALLS MODULAR BLOCK WALL (DRY CAST) Rather than being pre-approved as systems, the components of Modular block walls (dry cast) are pre-approved separately. The approved MBW components are