Joint Systems. System No. FF-D-0044
|
|
- Dina Chase
- 6 years ago
- Views:
Transcription
1 XHBN.FF-D-0044 System No. FF-D-0044 November 05, 2003 Assembly Rating 2 Hr Nom Joint Width 1 in. Class II and III Movement Capabilities 50% Compression or Extension 1. Floor or Wall Assembly Reinforced lightweight or normal weight ( pcf or kg/m 3 ) concrete having a min thickness of 4-1/2 in. (114 mm) at stepped-edges receiving joint cover (Item 3). 2. Mechanical Joint Assembly* Nom width of joint (at time of installation of joint system) is 1 in. (25 mm). The joint system fire barrier consists of a foil heat shield and an insulation block. The joint system fire barrier shall be installed in accordance with the installation instructions accompanying the units. CONSTRUCTION SPECIALTIES INC RFX-1F 3. Joint Cover Min in. (0.76 mm) thick joint cover formed of aluminum, bronze, stainless steel or galv steel. As an alternate, where the linear joint opening is enclosed within a chase wall and is non load bearing, a cover consisting of a creased sheet of min 2 mil stainless steel foil secured with 1 in. wide continuous galv steel washer strips along each side of the joint opening may be used. Joint cover anchored to floor slab on each side of joint opening, continuous over entire length of joint, in accordance with the manufacturer's installation instructions. *Bearing the UL Classification Mark This page and all contents are Copyright 2004 by Underwriters Laboratories Inc.
2 XHBN.WW-D-0060 Page Bottom Design/System/Construction/Assembly Usage Disclaimer Authorities Having Jurisdiction should be consulted in all cases as to the particular requirements covering the installation and use of UL Listed or Classified products, equipment, system, devices, and materials. Authorities Having Jurisdiction should be consulted before construction. Fire resistance assemblies and products are developed by the design submitter and have been investigated by UL for compliance with applicable requirements. The published information cannot always address every construction nuance encountered in the field. When field issues arise, it is recommended the first contact for assistance be the technical service staff provided by the product manufacturer noted for the design. Users of fire resistance assemblies are advised to consult the general Guide Information for each product category and each group of assemblies. The Guide Information includes specifics concerning alternate materials and alternate methods of construction. Only products which bear UL's Mark are considered as Classified, Listed, or Recognized. See General Information for System No. WW-D-0060 July 29, 2004 Assembly Rating 1 Hr Nom Joint Width 1 in. Class II and III Movement Capabilities 50% Compression or Extension
3 1. Wall Assembly Min 4-1/2 in. (114 mm) thick lightweight or normal weight ( pcf or kg/m 3 ) reinforced structural concrete. Wall may also be constructed of any UL Classified Concrete Blocks*. See Concrete Blocks (CAZT) category in the Fire Resistance Directory for names of manufacturers. 2. Mechanical Joint Assembly* Nom width of joint (at time of installation of joint system) is 1 in. (25 mm). The joint system fire barrier consists of an insulation block. The joint system fire barrier shall be installed in accordance with the installation instructions accompanying the units. CONSTRUCTION SPECIALTIES INC RFX-1W 3. Joint Cover Min in. thick joint cover formed of aluminum, bronze, stainless steel or galv steel. Joint covers anchored to each side of wall on both sides of joint opening, continuous over entire length of joint, in accordance with the manufacturer's installation instructions. As an alternate, in the area from the finished ceiling to the floor above, a cover consisting of a creased sheet of min 2 mil stainless steel foil secured with 1 in. wide continuous galv steel washer strips along each side of the joint opening may be used. *Bearing the UL Classification Mark Last Updated on Questions? Print this page Notice of Disclaimer Page Top Copyright 2011 Underwriters Laboratories Inc. The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufactured under UL's Follow-Up Service. Only those products bearing the UL Mark should be considered to be Listed and covered under UL's Follow-Up Service. Always look for the Mark on the product. UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide Information, Designs and/or Listings (files) must be presented in their entirety and in a non-misleading manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from Underwriters Laboratories Inc." must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following format: "Copyright 2011 Underwriters Laboratories Inc. "
4
5 XHBN.WW-D-0049 System No. WW-D-0049 November 05, 2003 Assembly Rating 2 Hr Nom Joint Width 1 in. Class II and III Movement Capabilities 50% Compression or Extension 1. Wall Assembly Min 6 in. (152 mm) thick lightweight or normal weight ( pcf or kg/m 3 ) reinforced structural concrete. Wall may also be constructed of any UL Classified Concrete Blocks*. See Concrete Blocks (CAZT) category in the Fire Resistance Directory for names of manufacturers. 2. Mechanical Joint Assembly* Nom width of joint (at time of installation of joint system) is 1 in. (25 mm). The joint system fire barrier consists of an insulation block. The joint system fire barrier shall be installed in accordance with the installation instructions accompanying the units. CONSTRUCTION SPECIALTIES INC RFX-1W 3. Joint Cover Min in. thick joint cover formed of aluminum, bronze, stainless steel or galv steel. Joint covers anchored to each side of wall on both sides of joint opening, continuous over entire length of joint, in accordance with the manufacturer's installation instructions. As an alternate, in the area from the finished ceiling to the floor above, a cover consisting of a creased sheet of min 2 mil stainless steel foil secured with 1 in. wide continuous galv steel washer strips along each side of the joint opening may be used. *Bearing the UL Classification Mark This page and all contents are Copyright 2004 by Underwriters Laboratories Inc.
6 XHBN.WW-D Page 1 of 3 XHBN.WW-D-0059 Page Bottom Print-friendly version Questions? Previous Page See General Information for System No. WW-D-0059 July 29, 2004 Assembly Rating 1 Hr Nom Joint Width 1 in. Class II and III Movement Capabilities 50% Compression or Extension mhtml:file://t:\ul%20listings\rfx\ww-d-0059.mht 5/15/2006
7 XHBN.WW-D mhtml:file://t:\ul%20listings\rfx\ww-d-0059.mht Page 2 of 3 5/15/ Wall Assembly The 1 hr fire rated framed gypsum wallboard wall assembly shall be constructed of the materials and in the manner specified in the individual U300 or U400 Series Wall and Partition Designs in the UL Fire Resistance Directory and shall include the following construction features: A. Studs Steel studs to be min 3-1/2 in. (89 mm) wide and spaced max 24 in. (610 mm) OC. Wood studs to be nom 2 by 4 in. (51 by 102 mm) lumber spaced max 16 in. (406 mm) OC. B. Gypsum Board* Gypsum board sheets to be installed to a min total thickness of 5/8 in. (16 mm) on each side of wall and on each stud face within joint opening. 2. Mechanical Joint Assembly* Nom width of joint (at time of installation of joint system) is 1 in. (25 mm). The joint system fire barrier consists of an insulation block. The joint system fire barrier shall be installed in accordance with the installation instructions accompanying
8 XHBN.WW-D mhtml:file://t:\ul%20listings\rfx\ww-d-0059.mht Page 3 of 3 5/15/2006 the units. CONSTRUCTION SPECIALTIES INC RFX-1W 3. Joint Cover Min in. thick joint cover formed of aluminum, bronze, stainless steel or galv steel. Joint covers anchored to each side of wall on both sides of joint opening, continuous over entire length of joint, in accordance with the manufacturer's installation instructions. As an alternate, in the area from the finished ceiling to the floor above, a cover consisting of a creased sheet of min 2 mil stainless steel foil secured with 1 in. wide continuous galv steel washer strips along each side of the joint opening may be used. *Bearing the UL Classification Mark Last Updated on Page Top UL Listed and Classified Products Notice of Disclaimer UL Recognized Components Questions? Products Certified for Canada Previous Page This page and all contents are Copyright 2005 by Underwriters Laboratories Inc. The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufactured under UL's Follow-Up Service. Only those products bearing the UL Mark should be considered to be Listed and covered under UL's Follow-Up Service. Always look for the Mark on the product. UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide Information, Designs and/or Listings (files) must be presented in their entirety and in a non-misleading manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from Underwriters Laboratories Inc." must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following format: "Copyright 2005 Underwriters Laboratories Inc. "
9 XHBN.WW-D-0048 System No. WW-D-0048 November 05, 2003 Assembly Rating 2 Hr Nom Joint Width 1 in. Class II and III Movement Capabilities 50% Compression or Extension 1. Wall Assembly The 2 hr fire rated framed gypsum board wall assembly shall be constructed of the materials and in the manner specified in the individual U300 or U400 Series Wall and Partition Designs in the UL Fire Resistance Directory and shall include the following construction features: A. Studs Steel studs to be min 3-1/2 in. (89 mm) wide and spaced max 24 in. (610 mm) OC. Wood studs to be nom 2 by 4 in. (51 by 102 mm) lumber spaced max 16 in. (406 mm) OC. B. Gypsum Board* Gypsum board sheets to be installed to a min total thickness of 1-1/4 in. (32 mm) on each side of wall and on each stud face within joint opening. 2. Mechanical Joint Assembly* Nom width of joint (at time of installation of joint system) is 1 in. (25 mm). The joint system fire barrier consists of an insulation block. The joint system fire barrier shall be installed in accordance with the installation instructions accompanying the units. CONSTRUCTION SPECIALTIES INC RFX-1W This page and all contents are Copyright 2004 by Underwriters Laboratories Inc.
10 3. Joint Cover Min in. thick joint cover formed of aluminum, bronze, stainless steel or galv steel. Joint covers anchored to each side of wall on both sides of joint opening, continuous over entire length of joint, in accordance with the manufacturer's installation instructions. As an alternate, in the area from the finished ceiling to the floor above, a cover consisting of a creased sheet of min 2 mil stainless steel foil secured with 1 in. wide continuous galv steel washer strips along each side of the joint opening may be used. *Bearing the UL Classification Mark This page and all contents are Copyright 2004 by Underwriters Laboratories Inc.
XHBN.FF-D Joint Systems. Joint Systems. System No. FF-D-3008
XHBN.FF-D-3008 - Page 1 of 2 XHBN.FF-D-3008 Page Bottom See General Information for System No. FF-D-3008 March 20, 2006 Assembly Rating 2 Hr Nominal Joint Widths 14, 16, 18 and 20 In. (See Item 2A) Class
More informationXHBN.FF-D Joint Systems. Design/System/Construction/Assembly Usage Disclaimer. Joint Systems. System No. FF-D-1066
XHBN.FF-D-1066 - http://database.ul.com/cgi-bin/xyv/template/lisext/1frame/showpage.html?name=xhbn.ff-d-10... Page 1 of 2 9/18/2009 Page Bottom XHBN.FF-D-1066 Design/System/Construction/Assembly Usage
More informationXHBN.HW-D Joint Systems. Design/System/Construction/Assembly Usage Disclaimer. Joint Systems. System No. HW-D-0631
Page Bottom XHBN.HW-D-0631 Joint Systems Design/System/Construction/Assembly Usage Disclaimer Authorities Having Jurisdiction should be consulted in all cases as to the particular requirements covering
More informationBXUV.V481. Fire Resistance Ratings - ANSI/UL 263. Design/System/Construction/Assembly Usage Disclaimer. Fire Resistance Ratings - ANSI/UL 263
Page Bottom BXUV.V481 Fire Resistance Ratings - ANSI/UL 263 Design/System/Construction/Assembly Usage Disclaimer Authorities Having Jurisdiction should be consulted in all cases as to the particular requirements
More informationJB ENGINEERING AND CODE CONSULTING, P.C Cardinal Drive Munster, IN Phone: Fax:
JB ENGINEERING AND CODE CONSULTING, P.C. 1661 Cardinal Drive Munster, IN 46321 Phone: 219-922-6171 Fax: 219-922-6172 E-Mail: JBEngineer@aol.com JULIUS A. BALLANCO, P.E. President January 15, 2008 Mr. Rick
More informationBXUV.U435. Fire Resistance Ratings - ANSI/UL 263. Design/System/Construction/Assembly Usage Disclaimer. Fire Resistance Ratings - ANSI/UL 263
Page Bottom BXUV.U435 Fire Resistance Ratings - ANSI/UL 263 Design/System/Construction/Assembly Usage Disclaimer Authorities Having Jurisdiction should be consulted in all cases as to the particular requirements
More informationDesign No. L565. Design No. L565
1 of 5 3/17/2015 6:18 PM Design No. L565 BXUV.L565 Fire Resistance Ratings - ANSI/UL 263 Page Bottom Design/System/Construction/Assembly Usage Disclaimer Authorities Having Jurisdiction should be consulted
More informationDesign No. M507. Design No. M507
1 of 5 3/17/2015 6:22 PM Design No. M507 BXUV.M507 Fire Resistance Ratings - ANSI/UL 263 Page Bottom Design/System/Construction/Assembly Usage Disclaimer Authorities Having Jurisdiction should be consulted
More informationUL Design System HW-D-1012 continued
UL System No. HW-D-1012 Assembly Ratings 1, 2 and 3 Hr (See Item 2) Nominal Joint Width 3 in. Class II and III Movement Capabilities 100% Compression or Extension Page 1 of 5 1. Floor Assembly The fire-rated
More informationPage 2 of 5 1. Flooring Systems The flooring system shall consist of one of the following: System No. 1 Subflooring Nom 23/32 in. thick wood structura
Page 1 of 5 Page Bottom Design No. L577 BXUV.L577 Fire-resistance Ratings - ANSI/UL 263 Design/System/Construction/Assembly Usage Disclaimer Authorities Having Jurisdiction should be consulted in all cases
More informationDesign No. U415 BXUV.U415 Fire-resistance Ratings - ANSI/UL 263. Design No. U415
Design No. U415 BXUV.U415 Fire-resistance Ratings - ANSI/UL 263 Page Bottom Design/System/Construction/Assembly Usage Disclaimer Authorities Having Jurisdiction should be consulted in all cases as to the
More informationFIRESTOP TECHNICAL PACK TEL: (888) 721-SEAL (7325) FAX: (888) 921-SEAL (7325)
FIRESTOP TECHNICAL PACK FIRESEAL 814 Acrylic Intumescent Caulk Polymer Adhesives Sealant Systems, Inc. 501 Garrett Morris Parkway Mineral Wells, TX 76067 TEL: (888) 721-SEAL (7325) FAX: (888) 921-SEAL
More informationThe System U.S. Patent No. 5,913,788
The System U.S. Patent No. 5,913,788 UL System No. HW-D-0027 2 Hour Rated Assembly (Metal Decking) UL System No. HW-D-0028 1 Hour Rated Assembly (Metal Decking) UL System No. HW-D-0208 1 Hour Rated Assembly
More informationBXUV.U415 - Fire Resistance Ratings - ANSI/UL 263. Fire Resistance Ratings - ANSI/UL 263
Page 1 of 7 Page Bottom BXUV.U415 Fire Resistance Ratings - ANSI/UL 263 Fire Resistance Ratings - ANSI/UL 263 See General Information for Fire Resistance Ratings - ANSI/UL 263 Design No. U415 July 30,
More informationUL Online Certifications Directory
Design No. N782 August 03, 2006 Restrained Beam Ratings 1, 1-1/2, 2, 3 and 4 Hr Unrestrained Beam Ratings 1, 1-1/2, 2, 3 and 4 Hr Load Restricted for Canadian Applications See Guide BXUV7 1. Steel Beam
More informationCEYDC.R25563 Nonmetallic Plumbing System Components Listed for Fire Resistance
INFO 33, page 1 CEYDC.R25563 Nonmetallic Plumbing System Components Listed for Fire Resistance HEATLINK GROUP INC R25563 4603E 13TH ST NE CALGARY, AB T2E 6M3 CANADA Types Purelink PEXa, Heatlink PEXa and
More informationPARKING PLAZA MEXICO COVERED GAS PUMP ISLAND PARKING BUS PARKING AREA. The Evans Group COVERD AREA TACO STAND COVERD AREA AREA FREEZER EXIT EXIT
OFFICE FUEL ISLAND ATTENDANTS OFFICE GAS PUMP ISLAND BUS SIGNAGE AND 6'-0" WALL TACO STAND COVERED RESTROOMS RESTROOMS MARKET TACO STAND PLAZA MEXICO COVERED FREEZER GAS PUMP ISLAND BUS FUEL ISLAND ATTENDANTS
More informationBXUV.U411. Fire Resistance Ratings - ANSI/UL 263. Design/System/Construction/Assembly Usage Disclaimer. Fire Resistance Ratings - ANSI/UL 263
Page Bottom BXUV.U411 Fire Resistance Ratings - ANSI/UL 263 Design/System/Construction/Assembly Usage Disclaimer Authorities Having Jurisdiction should be consulted in all cases as to the particular requirements
More informationSystem No. HW-D-0548
System No. Ì73hwdÇ%P+11bÎ ANSI/UL2079 Assembly atings - 1 and 2 Hr (See Item 2) Maximum Joint Width - 3/4, 1 or 1-1/2 In. (See Item 3) Class II Movement Capabilities - 50 or 100 %Compression or Extension
More informationFire Protection Products. Firestop Submittal Package FIP 1-Step Firestop Foam. Electrical Trade
Fire Protection Products Firestop Submittal Package FIP 1-Step Firestop Foam Electrical Trade Manufacturer: Fire Protection Products Ryan Fenstermaker 732.921.1503 rfenstermaker@mmm.com Electrical Products
More informationEVALUATION REPORT OF CENTRAL STATES MANUFACTURING, INC. 'CENTRAL-LOC PANEL' FLORIDA BUILDING CODE 5TH EDITION (2014) FLORIDA PRODUCT APPROVAL
- EVALUATION REPORT OF CENTRAL STATES MANUFACTURING, INC. 'CENTRAL-LOC PANEL' FLORIDA BUILDING CODE 5TH EDITION (2014) FLORIDA PRODUCT APPROVAL FL 14016.2-R2 STRUCTURAL COMPONENTS ROOF DECK Prepared For:
More informationSLOTTED STUD WIND-LOAD & NON-LOAD BEARING DEFLECTION WALL SYSTEM. U.L. FIRE RATED Head-of-Wall Joint Systems
SLOTTED STUD WIND-LOAD & NON-LOAD BEARING DEFLECTION WALL SYSTEM U.L. FIRE RATED Head-of-Wall Joint Systems 1-800-275-2279 STEELER INC. SLOTTED STUD 1-800-275-2279 The STEELER SLOTTED STUD is an innovative
More informationCAJ. Combos. C-AJ of 5. Through Penetrations Series. Concrete. 3Fire Protection Products
System No. C-AJ-8073 September 07, 2004 F Rating 2 Hr T Ratings 0, 3/4 and 2 Hr C-AJ-8073 1 of 5 1. Floor or Wall Assembly Min 4-1/2 in. thick reinforced normal weight (140-150 pcf) concrete. Wall may
More informationSystem No. HW-D-0119
System No. HW-D-0119 August 03, 2007 Assembly Rating 1, 2 and 3 Hr (See Item 2) Nominal Joint Width 1 In. Class II and III Movement Capabilities 100% Compression or Extension 1. Floor Assembly The fire-rated
More informationFIRESTOP JOINT SPRAY CFS-SP WB. 2mm (0.079") WET FILM ± 7.5 ± 5
Design No. CEJ 27 P (HI/JS 20-05) Table. CONCRETE FLOOR ASSEMBLY: Max. two-hour rated concrete floor assembly made from either lightweight or normal weight concrete with a density of 00-50 pcf, with a
More informationLISTING INFORMATION OF International Fireproof Technology Inc. - Joint Systems SPEC ID: 43848
LISTING INFORMATION OF International Fireproof Technology Inc. - Joint Systems SPEC ID: 43848 International Fireproof Technology Inc. 17528 Von Karman Avenue Irvine, CA 92614 This report is for the exclusive
More informationThrough-Fastener Panel UL Listing documentation
Through-Fastener Panel UL Listing documentation Class-4 Impact Rating Class-90 Fire Rating Tensile Strength: Grade 80/E Coil Thickness Range for 29 ga.: 0.0142 0.015 Coil Thickness Range for 26 ga.: 0.0182
More informationDesign No. D929 February 07, Restrained Assembly Rating 1, 1-1/2, 2, or 3 Hr. (See Items 1, 5, 9, 10, 14)
Design No. D929 February 07, 2003 Restrained Assembly Rating 1, 1-1/2, 2, or 3 Hr (See Items 1, 5, 9, 10, 14) Unrestrained Assembly Ratings 0 Hr (See Item 4 & 5) Unrestrained Beam Ratings 1, 1-1/2 or 2
More informationSUBMITTAL INDEX. Product Datasheets: Product Approvals:
Product Datasheets: HFP Pro Series Sleeve RevA HFP CD Plates RevA HFP Sleeve Extenions RevA HFP Water Dam RevA HFP Water Module RevA HFP Hollow Sleeve RevB HFP Cable Line Set RevA HFP Closet Flange RevA
More informationSubject: NRCA MRCA Joint Technical Bulletin. Date: January 2008 NOT COMPROMISE.
Roofing No. 3001 NRCA MRCA Joint Technical Bulletin Attached is a copy of the NRCA/MRCA Joint Technical Bulletin which was presented at the 1987 MRCA Convention. This document is entitled, In-Service R-Values
More informationDesign No. L551. Design No. L551
1 of 7 3/17/2015 6:13 PM Design No. L551 BXUV.L551 Fire Resistance Ratings - ANSI/UL 263 Page Bottom Design/System/Construction/Assembly Usage Disclaimer Authorities Having Jurisdiction should be consulted
More informationDuct Wrap Flexible Wraps
Design No. 3MU/ 60-01 December 23, 2010 VENTILATION DUCT PROTECTION 3M Company 3M Fire Barrier Duct Wraps: 615 and 615+ 3M Fire Barrier Sealants: Water-Tight 1000-NS Silicone, Water-Tight 1003-SL Silicone
More informationBXUV.L576 - Fire Resistance Ratings - ANSI/UL 263. Fire Resistance Ratings - ANSI/UL 263
Page 1 of 7 Page Bottom BXUV.L576 Fire Resistance Ratings - ANSI/UL 263 Fire Resistance Ratings - ANSI/UL 263 See General Information for Fire Resistance Ratings - ANSI/UL 263 Design No. L576 August 15,
More informationDesign No. D923 December 10, Restrained Assembly Ratings 3/4, 1, 1-1/2, 2 or 3 Hr. (See Items 2, 7, 8, 9 and 12)
Design No. D923 December 10, 2001 Restrained Assembly Ratings 3/4, 1, 1-1/2, 2 or 3 Hr (See Items 2, 7, 8, 9 and 12) Unrestrained Assembly Rating 0 Hr (See Item 4) Unrestrained Beam Ratings 1, 1-1/2, 2
More informationI-STUD Shaftwall System
I-STUD Shaftwall System Summit Tower I-Stud and CertainTeed Shaftliner TM MILL CERTIFIED Steel-Con 00% GALVANIZED Steel Construction Systems UL Evaluation Report No. ER3660-02 Intertek The I-Stud is approved
More informationFirestopping Submittal Package
Firestopping Submittal Package Project: Architect: General Contractor: Installation Contractor: Distributor (and Contact): Manufacturer's Representative: Rectorseal - Technical Services Ph (713) 263-8001
More informationSystem No. C-AJ-8048
System No. C-AJ-8048 F Rating - 2 Hr T Ratings - 0, 1/2, 3/4, 1 and 1-1/2 Hr (See Item 2) L Rating At Ambient Less Than 1 CFM / Sq. Ft. L Rating At 400 F 5 CFM / Sq. Ft. System No. C-AJ-8048 System No.
More informationresearch report Fire Resistance Ratings of Load Bearing Steel Stud Walls With Gypsum Wallboard Protection RESEARCH REPORT RP REVISION 2007
research report Fire Resistance Ratings of Load Bearing Steel Stud Walls With Gypsum Wallboard Protection RESEARCH REPORT RP81-1 1981 REVISION 2007 American Iron and Steel Institute Fire Resistance Ratings
More informationSystem No. C-AJ-8133
System No. C-AJ-8133 March 09, 2011 F Ratings - 1, 1-1/2, 2 and 3 Hr (See Item 2) T Ratings - 0, 1/2, 3/4, 1, 1-1/2, 2 and 3 Hr (See Item 2) 1. Floor or Wall Assembly Min 4-1/2 in. (114 mm) thick reinforced
More informationHow to modify a tested fire-rated wall to improve its STC sound rating, while maintaining its official fire-rated qualification
How to modify a tested fire-rated wall to improve its STC sound rating, while maintaining its official fire-rated qualification Harold FORESTER, Eng. 1 Forester Controls Canada ABSTRACT Local regulatory
More informationLISTING INFORMATION OF International Beams - IB Series Joists SPEC ID: 27316
LISTING INFORMATION OF International Beams - IB Series Joists SPEC ID: 27316 International Beams Inc. 2010 Boul. St-Elzear Quest Laval, QC H7L 3N4 CANADA This report is for the exclusive use of Intertek
More informationSystem No. C-AJ-8096
F Rating -- Hr T Rating -- 0, / and Hr (See Item ) B B E E G G F F A A C C D D 4B 4A SECTION A-A SECTION B-B July 0, 005 Page: of 5 F Rating -- Hr T Rating -- 0, / and Hr (See Item ) B A SECTION C-C SECTION
More informationI-STUD Shaftwall System
I-STUD Shaftwall System Summit Tower Spokane, WA I-Stud and CertainTeed Shaftliner MILL CERTIFIED 00% GALVANIZED UL Evaluation Report No. ER3660-02 Intertek SCAFCO I-Stud is approved with the following
More informationFIRESTOP SUBMITTAL PACKAGE
FIESTOP SUBMITTAL PACKAGE Head of Wall Firestop Submittal POJECT: DATE: September 28, 2011 SUBMITTED BY: Brent Johnson STI Firestop 415-515-3767 bjohnson@stifirestop.com 200 Evans Way Somerville, NJ 08876
More informationCONTRACT NUMBER: W912DQ-08-C % CORRECTED DESIGN 28 JULY 2008
SECTION 092900 - GYPSUM BOARD 1.1 SUMMARY A. This Section includes the following: 1. Interior gypsum board. 2. Tile backing panels. B. Related Sections include the following: 1. Division 06 Section "Rough
More informationBXUV.L548 - Fire Resistance Ratings - ANSI/UL 263. Fire Resistance Ratings - ANSI/UL 263
Page 1 of 8 Page Bottom BXUV.L548 Fire Resistance Ratings - ANSI/UL 263 Fire Resistance Ratings - ANSI/UL 263 See General Information for Fire Resistance Ratings - ANSI/UL 263 Design No. L548 December
More informationBXUV.U465. Fire Resistance Ratings - ANSI/UL 263. Design/System/Construction/Assembly Usage Disclaimer. Fire Resistance Ratings - ANSI/UL 263
Page Bottom BXUV.U465 Fire Resistance Ratings - ANSI/UL 263 Design/System/Construction/Assembly Usage Disclaimer Authorities Having Jurisdiction should be consulted in all cases as to the particular requirements
More informationDesign No. HI/BP PERIMETER FIRE BARRIER SYSTEM Hilti, Inc. ASTM E 2307 Table 1
FIRESTOP JOINT SPRAY CFS-SP WB SILICONE JOINT SPRAY CFS-SP SIL F-RATING 2-HR. 2-HR. T-RATING -HR. -HR. APPLICATION THICKNESS PERIMETER FIRE BARRIER SYSTEM Hilti, Inc. ASTM E 2307 Table /8" WET FILM (/6"
More informationSystem No. W-J-4050 ANSI/UL1479 (ASTM E814) CAN/ULC S115 4F2 4E. Reproduced by HILTI, Inc. Courtesy of. Underwriters Laboratories, Inc.
CLSS to UL 1479 and CN/ULC-S115 NSI/UL1479 (STM E814) CN/ULC S115 4 4F 4F1 4F 4F1 4 CONFIGURTION SECTION - Page: 1 of 5 CLSS to UL 1479 and CN/ULC-S115 NSI/UL1479 (STM E814) CN/ULC S115 4F 1 4G 4 4H CONFIGURTION
More informationDesign No. U553 BXUV.U553 Fire-resistance Ratings - ANSI/UL 263. Design No. U553
BXUV.U553 - Fire-resistance Ratings - ANSI/UL 263 Home Quick Guide Contact Us UL.com Design No. U553 BXUV.U553 Fire-resistance Ratings - ANSI/UL 263 Page Bottom Design/System/Construction/Assembly Usage
More informationInstallation. Resilmount A237R. Installation Instructions. Furring channel sound isolation clip
Resilmount A237R Furring channel sound isolation clip Installation Instructions Another Quality Building Product Installation A237R SPECIFICATIONS Width: 1-3/8 eight (including rubber): 1-1/16 Length:
More informationBXUV.L521 - Fire Resistance Ratings - ANSI/UL 263. Fire Resistance Ratings - ANSI/UL 263
Page 1 of 8 Page Bottom BXUV.L521 Fire Resistance Ratings - ANSI/UL 263 Fire Resistance Ratings - ANSI/UL 263 See General Information for Fire Resistance Ratings - ANSI/UL 263 Design No. L521 November
More informationDIVISION: THERMAL AND MOISTURE PROTECTION SECTION: FIRESTOPPING REPORT HOLDER: PASSIVE FIRE PROTECTION PARTNERS
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2996 Reissued 12/2017 This report is subject to renewal 12/2019. DIVISION: 07 00
More informationSUBMITTAL INDEX. Product Datasheets: Product Approvals:
Product Datasheets: SUBMITTAL INDEX HF Corrugated Deck Cast In Place Sleeve Non Met HF Corrugated Deck Optional Pipe Sleeve Non Met HF Corrugated Deck Seal Sleeve Non Met HF Optional Pipe Size Sleeve Non
More informationAPPENDIX DETAIL (1) INSULATION HAS 3-INCH TOP INSPECTION GAP AND EXTENDS 24 INCHES BELOW GRADE
The sections and construction details in Details 502.2.1.5(1), 502.2.1.5(2), 502.2.1.5(3), 502.2.1.5(4) and 502.2.1.5(5), and Tables 502.2.3.1(1), 502.2.3.1(2), 502.2.3.1(3), 502.2.3.2, 502.2.3.3, 502.2.3.5
More informationSECTION GYPSUM WALLBOARD SYSTEMS. A. Gypsum board at new wall partitions or where indicated on drawings. B. ASTM C442 - Gypsum Backing Board
SECTION 09260 GYPSUM WALLBOARD SYSTEMS PART 1 - GENERAL 1.1 SECTION INCLUDES A. Gypsum board at new wall partitions or where indicated on drawings. 1.2 REFERENCED STANDARDS A. ASTM C36 - Gypsum Wallboard
More informationStark Truss Company, Inc. Revised December 14, 2018
Fire-Rated Assemblies PR-S223 Stark Truss Company, Inc. Revised December 14, 2018 Products: SI-40, SI-60, and SI-80 Prefabricated Wood I-Joists Stark Truss Company, Inc. 8655 Chestnut Ridge Road, N.W.
More informationDesign No. D927 December 10, Restrained Assembly Ratings 3/4, 1, 1-1/2, 2 & 3 Hr. (See Items 1, 6, 7, 8 & 11) Unrestrained Assembly Ratings 0 Hr
Design No. D927 December 10, 2001 Ratings 3/4, 1, 1-1/2, 2 & 3 Hr (See Items 1, 6, 7, 8 & 11) Ratings 0 Hr (See Item 3) Beam Ratings 1, 1-1/2, 2 & 3 Hr (See Items 4, 4A, 7 & 11) Supports W8x28 min size
More informationDesign No. P725 December 10, Restrained Assembly Rating-1, 1-1/2 or 2 H (See Item 8) Unrestrained Assembly Rating-1, 1-1/2 or 2 H (See Item 8)
Design No. P725 December 10, 2003 Restrained Rating-1, 1-1/2 or 2 H (See Item 8) Rating-1, 1-1/2 or 2 H (See Item 8) Rating-1, 1-1/2 or 2 H (See Item 8) 1. Steel Supports W8X28 steel beam min size, 10K1
More informationThe GlasRoc Shaftliner Type X advantage...
C e r t a i n T e e d SHAFTLINER F o r A r e a S e p a r a t i o n F i r e w a l l s Shaftliner S Type X for Area Separation GlasRoc Shaftliner is a specially formulated product for applications where
More informationENGINEERING GROUP N. Dale Mabry Hwy. Suite 179 Tampa, FL, USA Tel: FL. C.O.A. #: 27620
00 & 00 0 Bruce B Downs Blvd MDC 6, Tampa FL 6 ISSUE DATE: 09/0/0 ISSUE PHASE: BID DOCUMENTS HALL ENGINEERING GROUP PROJECT NO. 07A H A L L ENGINEERING GROUP 99 N. Dale Mabry Hwy. Suite 79 Tampa, FL, USA
More informationSt. Monica Food Pantry
St. Monica Food Pantry 07 8400-1 SECTION 07 8400 - FIRESTOPPING PART 1 - GENERAL 1.1 SUMMARY: A. Related work: 1. Concrete. 2. Mortar and grout. 3. Brick masonry. 4. Concrete unit masonry. 5. Structural
More informationExpansion Joint Covers
Expansion Joint Covers 07 95 00 (079513) PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General Conditions, Supplementary Conditions and Division-1
More informationEDGEWATER, FLORIDA JUNE 14, 2010
SECTION 09 2900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationLISTING INFORMATION OF Mitek Design No. MCI/WI SPEC ID: MiTek Canada, Inc. 100 Industrial Road Bradford, ON L3Z 3G7 Canada
LISTING INFORMATION OF Mitek Design No. MCI/WI 60-02 SPEC ID: 27680 MiTek Canada, Inc. 100 Industrial Road Bradford, ON L3Z 3G7 Canada This report is for the exclusive use of Intertek s Client and is provided
More informationNATIONAL GYPSUM COMPANY 3-Hour Area Separation Wall System
-Hour Wall System The -hour Wall System is a -hour fire wall consisting of two layers of in. (. mm) shaftliner panels friction-fit between in. (0. mm) light-gauge steel H-Studs and a layer of /" Fire-Shield
More informationPinkWood Ltd. Revised September 29, 2017
Fire-Rated Assemblies PR-S315 PinkWood Ltd. Revised September 29, 2017 Products: Series I-Joists PinkWood Ltd., 5929 6 th St. NE, Calgary, Alberta, Canada T2K 5R5 (403) 279-3700 www.pinkwood.ca 1. Basis
More informationFlorida Building Code Edition Section D (Steep Sloped Roof System) Owens Corning
Florida Building Code Edition 2010 High-Velocity Hurricane Zone Uniform Permit Application Form. Section D (Steep Sloped Roof System) Roofs System Manufacturer Notice of Acceptance Number: Owens Corning
More informationFIRESTOP SUBMITTAL PACKAGE
FIRESTOP SUBMITTAL PACKAGE 200 Evans Way Somerville, NJ 08876 (800) 992-1180 (908) 526-8000 Fax (908) 526-9623 SPECIFIED TECHNOLOGIES INC. THE FIRESTOPPING SPECIALISTS Mechanical Wood Floor-Ceilings SYSTEM
More informationExpansion Joint Covers (079513)
Expansion Joint Covers 07 95 00 (079513) PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General Conditions, Supplementary Conditions and Division-1
More informationDesign No. D925 December 10, Restrained Assembly Ratings 3/4, 1, 1-1/2, 2 or 3 Hr. (See Items 1, 6 and 10)
Design No. D925 December 10, 2003 s 3/4, 1, 1-1/2, 2 or 3 (See Items 1, 6 and 10) 0 (See Items 3, 4, 4A and 10) s 1, 1-1/2, 2, 3 and 4 (See Items 4, 4A and 10) Supports W8x28 or W12x16 min size steel beam
More informationBoise Cascade Company Revised June 25, 2018
Fire-Rated Assemblies PR-S255 Boise Cascade Company Revised June 25, 2018 Products: GPI, WI, and BSI I-Joists Boise Cascade Company, 1000 North Park Drive, Roxboro, North Carolina 27573 (336) 599-1000
More informationTYPICAL BEARING WALL FRAMING
BASIC WOOD FRAMING City of Grand Rapids Building Safety Division 218-326-7601 www.grandrapidsmn.org This handout is intended only as a guide and is based in part on the 2007 Minnesota State Building Code,
More informationICC-ES Evaluation Report Reissued May 1, 2010 This report is subject to re-examination in two years.
ICC-ES Evaluation Report ESR-1255 Reissued May 1, 2010 This report is subject to re-examination in two years. www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council
More informationAssemblies Evaluated For 1. Non Axial Load Bearing Wall 2. Transverse Load Capacity 3. Fire Resistance 4. Abuse Resistance
Pei Evaluation Service is an accredited ISO Standard 17065 Product Certifier, accredited by the IAS. This Assembly Evaluation Report represents a product that Pei ES has Evaluated. This Assembly Evaluation
More informationDesign No. P922 September 26, Restrained Assembly Rating 1, 1-1/2 or 2 Hr (See Items 6, 7) Unrestrained Assembly Rating 0 Hr (See Item 6)
Design No. P922 September 26, 2003 Restrained Assembly Rating 1, 1-1/2 or 2 Hr (See Items 6, 7) Unrestrained Assembly Rating 0 Hr (See Item 6) Unrestrained Beam Rating 1, 1-1/2 or 2 Hr (See Item 7) 1.
More informationDesign No. P921 April 16, Restrained Assembly Rating 1, 1-1/2 or 2 Hr (See Items 4, 6, 7 and 9) Unrestrained Assembly Rating 0 Hr (See Item 7)
Design No. P921 April 16, 2003 Restrained Assembly Rating 1, 1-1/2 or 2 Hr (See Items 4, 6, 7 and 9) Unrestrained Assembly Rating 0 Hr (See Item 7) Unrestrained Beam Rating 1, 1-1/2 or 2 Hr (See Items
More informationDivision 07 Thermal and Moisture Protection Thermal Protection Blanket Insulation Page 1 of 11
07 21 16 Blanket Insulation Page 1 of 11 Unifrax I LLC Design No. UNI/BI 120-14 FIRE RESISTANT GREASE DUCT FyreWrap Elite 1.5 Duct Insulation ASTM E 2336-16 and ICC-ES Acceptance Criteria for Grease Duct
More informationNATIONAL GYPSUM COMPANY 2-Hour Area Separation Wall System
0 00/NGC NATIONAL GYPSUM COMPANY -Hour Wall System The -Hour is a -hour fire wall consisting of in. (0. mm) light-gauge steel H-Studs that secure two layers of in. (. mm) shaftliner panels friction-fit
More informationDivision 07 Thermal and Moisture Protection Thermal Protection Blanket Insulation Page 1 of 17
07 21 16 Blanket Insulation Page 1 of 17 Design Number UNI/BI 120-03 FIRE RESISTANT GREASE DUCT Unifrax I LLC FyreWrap Elite 1.5 Duct Insulation CAN/ULC S144 Fire Resistance Rating 2 hours Fire Inside
More informationTYPICAL BEARING WALL FRAMING Joints in plates must be offset by 24 min.
FRAMING TIPS City of Grand Rapids Building Safety Division 218-326-7601 www.grandrapidsmn.org This handout is intended only as a guide and is based in part on the 2007 Minnesota State Building Code, Grand
More informationStandard Installation Fire Damper Models: 119, 119(F), 119(SS), D19
Standard Installation Fire Damper Models: 119, 119(F), 119(SS), D19 Page 1 or 8 APPLICATION This fi re damper is intended to restrict the passage of fl ame. The standard installation requires that the
More informationCode Compliance for Fire Resistance-Rated Assemblies in Light-Frame Buildings
Code Compliance for Fire Resistance-Rated Assemblies in Light-Frame Buildings Michelle Kam-Biron, PE, SE, SECB Senior Director, Education American Wood Council Copyright This presentation is protected
More informationResponse to Bidder Questions
Arcus Design Group - Architects, Inc. 101 Church Street, Suite 10 Malvern, Pennsylvania 19355 610-458-9900 Fax: 610-647-2883 www.arcusdg.com Response to Bidder Questions PROJECT NAME: Bryn Mawr Trust 400
More informationDSC BUILDING 1200 ALTERATIONS OCTOBER 2011 SECTION DUCT INSULATION
SECTION 230713 DUCT INSULATION PART 1 GENERAL 1.1 SUMMARY A. Related Sections: 1. 233113 Ductwork and Accessories 1.2 REFERENCES A. American Society for Testing and Materials (ASTM): 1. E84-96a Test Method
More informationPromat PROMASEAL Fire Barrier
Promat PROMASEAL Fire Barrier PRODUCT DESCRIPTION Promat PROMASEAL Fire Barriers are slabs of high density rock wool with a white endothermic, ablative coating. APPLICATION Promat PROMASEAL Fire Barriers
More informationSECTION GYPSUM BOARD
SECTION 09 29 00 GYPSUM BOARD PART 1 - GENERAL 1.01 SUMMARY A. Section Includes 1. Gypsum board screw attached to wood framing and furring members, joint treatment, and accessories. 2. Installation of
More informationENGINEERING EVALUATION
ENGINEERING EVALUATION REPORT NUMBER: 318773MID-003 ORIGINAL ISSUE DATE: August 28, 2009 REVISION AND DATE: Original EVALUATION CENTER Intertek 8431 Murphy Drive Middleton, WI 53562 RENDERED TO Hanchett
More information2009 International Building Code Errata (Portions of text and tables not shown are unaffected by the errata)
TWELFTH PRINTING (Updated December 6, 2016) Note for 706.5.1: This is an erratum in the 8 th, 9 th, 10 th and 11 th printing only. The reference is correct in other editions. 706.5.1 Exterior walls. Where
More informationA. Product Data: Identify thermal conductivity, thickness, and jackets (both factory and field applied, if any), for each type of product indicated.
SECTION 23 07 13 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationGarage/Accessory Structures
Garage/Accessory Structures City of New Prague Building Inspections Department 118 Central Ave N New Prague, MN 56071 (952) 758-4401 Fax (952) 758-1149 Requirements for submitted Building Plans Signed
More informationICC ES SYSTEM SYSTEM. Trusted DIVISION: 07 SECTION: AND FINISH REPORT HOLDER: ICC-ES Evaluation. Reissued 08/2016.
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.orgg ESR 2562 Reissued 08/206 This report is subject to renewal 08/208. DIVISION: 07 00 00
More informationSpecial Applications. Dorn Equipment, Corporation 27 Upham Street Melrose, MA Phone: Fax:
Special Applications Outdoor Protection When using the FIRSTO units outdoors, or wherever vapor or moisture barrier is needed, an application of FIWA sealant is used. The sealant should be applied to any
More informationSECTION WALL AND DOOR PROTECTION
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 10 26 00 WALL AND DOOR PROTECTION SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable to
More information(Project Location) (your firm's name)
SECTION 07 21 00 THERMAL INSULATION PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including the Conditions of the Contract and Division 01 Specification Sections
More informationBUILDING CODE REQUIREMENTS
Wood-frame walls and floors offer designers a unique opportunity to provide structures with economy as well as proven energy performance. Where these assemblies are required by the building codes to achieve
More informationSystem No. HW-D System No. HW-D-0262
8/24/2015 XHBN.HW-D-0262 - Joint Systems System No. HW-D-0262 XHBN.HW-D-0262 Joint Systems Page Bottom Design/System/Construction/Assembly Usage Disclaimer Authoritie s Having Jurisdiction should be consulte
More informationDIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER: TRESPA NORTH AMERICA, LTD.
0 ICC ES Report ICC ES (800) 423 6587 (562) 699 0543 www.icc es.org 000 Most Widely Accepted and Trusted ESR 1687 Reissued 02/2016 This report is subject to renewal 02/2017. DIVISION: 07 00 00 THERMAL
More informationDECEMBER Phone: Fax:
DECEMBER 007 TM system components www.nsiindustries.com Phone: 800.1.587 Fax: 800.81.5566 Table of Contents FireStop System Components Intumescent Caulk...1 Silicone...1 Silicone SL... FireStop81.... FireBlock16...
More information138 H-STUD AREA SEPARATION WALL SYSTEM
H-STUD AREA SEPARATION WALL SYSTEM The fire-protection of gypsum-based Area Separation Walls is demonstrated in dramatic fashion by the results of this actual townhouse fire in which the two-hour fire-rated
More information