Theut Company,LLC Theut Company, LLC

Transcription

1 Theut Company,LLC Theut Company, LLC P.O. Box 894 Columbus, Texas Phone: FAX: LETTER OF TRANSMITTAL 287 Date: 7/18/13 Project ID: DIV Product data package DIV To: Division One Project: David Anthony Middle School 18 Attn: Danny Struzick We are sending you Attached Under separate cover via the following: Shop Drawings Prints Samples Product Data Change Order Contract Other: Copies Description New Resubmit Checked Delivery 1 Product Data Package FTP SITE 1 Installation Manual FTP SITE 1 Test Data FTP SITE These are transmitted as checked below: For approval For your use As requested For review and comment Remarks: LEED Information will follow Resubmitted for approval Returned Revised sets Other: Physical Samples will be sent to Division One's Office (Haz Com, MSDS,ColorCharts, finish samples) Glass samples will be sent ASAP Kevin Henson Project Manager Theut Company, LLC

2 Submission - DIV Transmittal Date: 7/18/13 Transmittal Type: Product Data Transmittal No. 287 Pages: 77 Method: Theut ftp Site Theut Company, LLC Glass and Glazing Product Data Package David Anthony Middle School Greenhouse Road Cypress, TX Please Send back 1 approved copy of Product Data back to Theut Company, LLC DIV Please contact Theut Company about missing material Submission 18-Jul-13

3 Theut Company, LLC Glass and Glazing Product Data Package Architect: Bay-IBI Architects, Inc Gulf Freeway, P O Bo Houston, TX Contractor: DivisionOne Construction Northwest Freeway, Suite 150 Houston, TX Glazing Contractor: Theut Company, LLC 1317 Business 71 West Columbus, Tx DIV

4 Theut Company, LLC Glass and Glazing Product Data Package Glass and Panels G1 G4 G5 G7 G8 G8G 1/4 Clear Temp Material List System Ext /Int Color Warranty Options Doors Rugged Wide Stile Interior Clear-Class 2 1 Year 1/4" Glazing, 4" Top Rail 8" Mid Rail, 10" Bottom Rail Rugged Wide Stile Exterior Clear-Class 2 1 Year 1" Glazing, 4" Top Rail, 8" Mid Rail,10" Bottom Rail Framing System Reliance TC-IG Exterior Clear-Class 2 1 Year Front Set, 1" Glazing, 2 1/2" x 7 1/4" (2 1/2" x 10 1/8" Vertical members) FG-3000 Screwspline Interior Clear-Class 2 1 Year Center Set 2" x 4 1/2" (1/2" Glazing) FG-2000 Interior Clear-Class 2 1 Year Center Set 1 3/4" x 4 1/2" (1/4" Glazing) Sun Shades Solar Eclipse Exterior Clear 1 Year See shop drawings Sealants Tremco Curtainwall Sealant Black 5 Years Bedding Sealant Film Sonneborn Backer Rod Exterior 1/4 SN-54 on Green Temp - 1/2 Mill Spacer - 1/4 Clear Temp 1/4 Green Frit on Clear HS 1/4 SN-54 on Green#2 Temp - 1/2 Mill Spacer - 1/8 Clear Ann Clear PVB - 1/8 Clear Ann 1/4 Clear Ann Clear PVB - 1/4 Clear Ann 1/4 Clear Ann Clear PVB - 1/4 Clear Ann 5 Years Sealant Backing NP1 Interior Color to be selected 5 Years Perimeter Sealant NP 1 Exterior Color to be selected 5 Years Perimeter Sealant PVB Interlayer Interior Graphic Design 1 Year Design per Architect Light Shelves OBE solar light shelf Interior Clear-Class 2 1 Year See Shop Drawings Sliders Nana Wall SL-45 Interior Clear 1 Year SEE SEPEARATE SUBMITTAL FOR DRAWING Metal Craft Display Slider Interior Clear 1 Year 4" Frame w/ 1/4" Glazing Brake Metal PAC-CLAD Exterior Clear-Class 2 1 Year Break metal Shapes

5 Theut Company, LLC Glass and Glazing Product Data Package Leed Project: Yes Engineering Required: No Shop Drawings: Yes MSDS: Yes Schedule of Values: Yes Test Report: Yes Haz Com Manual: Yes Maint. Manual: Yes Install Manual: Yes Color Charts: Yes Finished Samples: Yes

6

7 VISTAWALL Rugged Entrance Systems Vistawall Rugged Entrance systems are engineered to offer long-lasting durability for high traffic areas. Their heavy-duty, tubular door members are securely attached with bolted corner blocks and back-up plates with two welded points per corner. The systems are monumental with 3 16-inch wall thickness and a door depth of 2 inches for even more strength. There are no exposed screws or fasteners to interrupt the door s smooth, clean lines. The Vistawall Nightwatch concealed rotary astragal for pairs of doors can be combined with Rugged Entrance Systems. This unique combination is ideal for schools and other public buildings. The design withstands abusive, heavy traffic during the day, as well as providing extra protection against vandalism at night. Rugged Entrance systems are also available with the Vistawall VIP I or II mid-panel exit device, a concealed vertical rod device unobtrusively placed within the mid-panel. Finishes include anodized black, bronze and clear as well as high performance painted finishes. If you need an entrance that can take some hard knocks and still have a lot of stile, call your local Vistawall sales representative or customer service 3" (76.2mm) RUGGED NS department. You can also reach Vistawall on the world wide web at 4 1/4" (107.9 mm) RUGGED MS RUGGED WS 5 1/2" (139.7 mm)

8 VISTAWALL STEEL BACKUP PLATE CORNER BLOCK MIG FILLET WELD Rugged Entrance Systems STILE MIG FILLET WELD (4) #10 P.H.S.M.S. (3) 1/4-20 BOLTS BOTTOM RAIL Torque resistant corner construction is achieved at all four corners. The 1 4" thick corner block is attached to the stile with (3) bolts, two of which are secured to a.160" thick steel backup plate. The rail is attached to the corner block with (4) #10 screws. The stile, bottom rail and corner block are all further connected with two high quality MIG welds. This construction insures a strong and tight corner connection. Vistawall Rugged Entrance Systems are designed for heavy traffic and abuse without sacrificing aesthetic appeal. These entrances require minimal maintenance and accept many types of hardware. Features of these entrances include: Tubular construction with welded corners 30 % heavier than standard doors 3 16" wall thickness and 2" depth Optional cross rails of 2", 5" & 9" Steel back up plate for hinges Framing also available in 2" x 4 1 2" flush glaze, HP subframe and CW250 subframe Optional Nightwatch security astragal for added security on pairs of doors Optional VIP midpanel exit assemblies Optional interlocking stiles and jambs Optional continuous gear hinges Anodized black, bronze, and clear High performance painted finishes Other Vistawall products include standard entrances, store fronts, window systems and curtain walls as well as Naturalite Skylight Systems, Skywall Translucent Systems and Modu-Line Window Systems. 4 1/2" (114.3 mm) 1 3/4" (44.4 mm) 3/32"(2.4 mm) 3"(76.2mm) 4 1/4"(107.9 mm) 5 1/2"(139.7 mm) 2" (50.8 mm) STANDARD JAMB AND STILES Vistawall locations: Headquarters P.O. Box 629, Terrell, TX Atlanta, GA Chicago, IL Cincinnati, OH Cleveland, OH Dallas, TX Denver, CO. Houston, TX Las Vegas, NV Los Angeles, CA Modesto, CA Newnan, GA San Francisco, CA Seattle, WA St. Louis, MO Tampa, FL Terrell, TX Warwick, RI Washington, DC 4 1/2" (114.3 mm) 2" (50.8 mm) INTERLOCKING JAMB AND STILES 1 3/4" (44.4 mm) 3/32"(2.4 mm) 3"(76.2mm) 4 1/4"(107.9 mm) ENGINEERED TO LAST 5 1/2"(139.7 mm) THE VISTAWALL GROUP BUTLER MANUFACTURING COMPANY

9 Theut Company, LLC Project Submittal Package storefronts Non-Thermal Flush Glaze FG-2000 Section 5

10 Victoria s Secret Chino Hills, CA Architect: McCall Design Group storefronts 5/2011 S.5 P.1

11 Standard Flush Glaze Storefront Systems a wide range of storefront framing systems for efficient installation Oldcastle BuildingEnvelope offers a complete line of storefront framing systems to meet just about any storefront application and condition. The Series 1000 is 1-3/4" x 4", and the Series 2000 is 1-3/4" x 4-1/2". Both are designed for 1/4" glazing but are easily adapted to 5/16" or 3/8" infills. The Series 3000 (2" x 4-1/2") is designed for 1" glazing and is adaptable to many different infills ranging from 1/4" to 1-1/8". Features Three different assembly methods: Screw Spline, Shear Block and Stacking standard flush glaze systems Tested by independent laboratories: - Air Infiltration: <.06 allowable at 6.24 PSF - Water Resistance: 10 PSF Door framing components Sidelite bases to match door bottom rails Multiple corner post configurations Adjustable and 135 mullion Anodized or painted finishes St. Benedicts Medical Arts Building, Ogden, UT Architect: Babcock Design Group

12 standard flush glaze systems Details FG-1000 FG-2000 FG-3000 Screw Spline Assembly Shear Block Assembly Stack Assembly 135 Corner Adjustable Mullion 2425 Olympic Boulevard, Suite 525-East Santa Monica, CA OLDCASTLE ( ) oldcastlebe.com

13 Storefronts: Non-Thermal Flush Glaze FG-2000 Introduction Oldcastle BuildingEnvelope offers a complete line of storefront framing systems to meet virtually any application and condition. FG-2000 is 1-3/4" x 4-1/2" and is designed for 1/4" glazing but is easily adapted to receive 5/16" or 3/8" infills. storefronts Specifications For specifications on FG-2000 Storefronts products, go to and click on Specifications. Windload Charts For detailed windload charts for FG-2000 Storefronts products log on to and click on Windload Charts. Features and Performance Data Features n Overall system dimensions: 1-3/4" x 4-1/2" n Center set glazing configuration n Screw spline, shear block and stacking assembly n Outside and inside glazed Performance Data n Air Infiltration: <.06 CFM/SQ 6.24 PSF per ASTM E283 n Static Water: 10 PSF per ASTM E331 n Deflection Load and Structural Load per ASTM E330 n Accommodates 1/4" thru 3/8" infill n 90 and 135 corners n Adjustable vertical mullions n Factory-painted Kynar 500 /Hylar 5000 finishes, meeting all provisions of AAMA 2605 nfactory-anodized finishing 5/2011 S.5 P.28

14 storefronts Storefronts: Non-Thermal Flush Glaze FG-2000 Detail Scale = 1/4 Size H0502 H0512 V0502 V0512 V0511 V0515 V0506 V0507 V0508 H0541 H0501 H0543 Detail numbers (e.g., H8801) reference website detail numbers. For those details not shown in this catalog and for additional information see: H /4" 1/4" FG-2122 FG /2" H0502 FG-2122 FG-2103 FG-2102 FG-2103 FG-2106 FG /2" 1/4" 1-3/4" H0501 V0502 V0506 FG-2106 FG-2105 FG-1200 H0509 5/2011 S.5 P Olympic Boulevard n Suite 525-East n Santa Monica, CA OLDCASTLE ( ) n oldcastlebe.com

15 Storefronts: Non-Thermal Flush Glaze FG-2000 Detail Scale = 1/4 Size MO-244 1" MO-243 These members may or may not be used storefronts 1-3/4" FG /2" H0512 FG-2108 FG-2109 FG-2155 FG-2154 FG-2106 FG-2106 FG /4" V0507 V0508 FG-2102 H0541 FG-2110 FG-2106 FG-2106 FG-2141 FG-2169 FG-2110 V0515 H0543 FG-2111 FG-2111 FG-2112 FG-2112 V0511 V0512 5/2011 S.5 P.30

16 Theut Company, LLC Project submittal package storefronts Non-Thermal Flush Glaze FG Section 5

17 Victoria s Secret Chino Hills, CA Architect: McCall Design Group storefronts 5/2011 S.5 P.1

18 Standard Flush Glaze Storefront Systems a wide range of storefront framing systems for efficient installation Oldcastle BuildingEnvelope offers a complete line of storefront framing systems to meet just about any storefront application and condition. The Series 1000 is 1-3/4" x 4", and the Series 2000 is 1-3/4" x 4-1/2". Both are designed for 1/4" glazing but are easily adapted to 5/16" or 3/8" infills. The Series 3000 (2" x 4-1/2") is designed for 1" glazing and is adaptable to many different infills ranging from 1/4" to 1-1/8". Features Three different assembly methods: Screw Spline, Shear Block and Stacking standard flush glaze systems Tested by independent laboratories: - Air Infiltration: <.06 allowable at 6.24 PSF - Water Resistance: 10 PSF Door framing components Sidelite bases to match door bottom rails Multiple corner post configurations Adjustable and 135 mullion Anodized or painted finishes St. Benedicts Medical Arts Building, Ogden, UT Architect: Babcock Design Group

19 standard flush glaze systems Details FG-1000 FG-2000 FG-3000 Screw Spline Assembly Shear Block Assembly Stack Assembly 135 Corner Adjustable Mullion 2425 Olympic Boulevard, Suite 525-East Santa Monica, CA OLDCASTLE ( ) oldcastlebe.com

20 Storefronts: Non-Thermal Flush Glaze FG-3000 Introduction Oldcastle BuildingEnvelope offers a complete line of storefront framing systems to meet virtually any application and condition. FG-3000 is 2" x 4-1/2" and is designed for 1" glazing but is easily adapted to receive 1/4" thru 1-1/8" infills. storefronts Specifications For specifications on FG-3000 Storefronts products, go to and click on Specifications. Windload Charts For detailed windload charts for FG-3000 Storefronts products log on to and click on Windload Charts. Features and Performance Data Features n Overall system dimensions: 2" x 4-1/2" n Center set glazing configuration n Screw spline, shear block and stacking assembly n Outside and inside glazed Performance Data n Air Infiltration: <.06 CFM/SQ 6.24 PSF per ASTM E283 n Static Water: 10 PSF per ASTM E331 n Deflection Load and Structural Load per ASTM E330 n Accommodates 1/4" thru 1-1/8" infill n 90 and 135 corners n Adjustable vertical mullions n Factory-painted Kynar 500 /Hylar 5000 finishes, meeting all provisions of AAMA 2605 n Factory-anodized finishing 5/2011 S.5 P.31

21 storefronts Storefronts: Non-Thermal Flush Glaze FG-3000 Detail Scale = 1/4 Size H0602 H0612 V0602 V0610 V0611 V0612 V0607 V0608 H0641 H0601 V0606 H0643 H0609 FG-2122 SEE SHOP DRAWINGS FOR SPECIFIC DETAILS 2" 1/4" Detail numbers (e.g., H8801) reference website detail numbers. For those details not shown in this catalog and for additional information see: Elevation Sample A: Storefront FG /2" H0602 FG-3103 FG-3103 FG-3101 FG-2122 H /2" FG-3144 FG-3142 FG-3102 FG /4" H0601 2" V0602 V0602 V0606 V0606 V0610 V0610 H0601 FG-3144 FG-3161 FG-2169 H0609 H Olympic Boulevard Suite 525-East Santa Monica, CA OLDCASTLE ( ) oldcastlebe.com n 5/2011 S.5 P.32 n n

22 Storefronts: Non-Thermal Flush Glaze FG-3000 Detail Scale = 1/4 Size 1/4" These members may or may not be used storefronts 1" MO-234/ MO-244 2" FG /2" FG-3108 FG-3180 FG-3181 H0612 FG-3144 FG " V0607 V0608 FG-2141 FG-3102 FG-3110 H0641 FG-3144 FG-3178 FG-3110 V0612 FG-2169 FG-3111 H /2" V0611 FG /2011 S.5 P.33

23 Curtain Wall: Reliance -TC IG Introduction To complement the popular Reliance Curtain Wall platform, Oldcastle BuildingEnvelope has developed a thermal composite inside glazed curtain wall system, Reliance -TC IG. This system takes thermal performance to a higher level through the use of glass reinforced polyamide strips in the construction of all horizontal and vertical members. Reliance -TC IG is available in both 7-1/4" and 6" depths and is available with either captured or structural silicone glazed verticals. This system has dual-color finish capability and allows for entrance door and operable window adaptability. curtain wall Specifications For specifications on Curtain Wall: Reliance -TC IG products, go to and click on Specifications. Windload Charts For detailed windload charts for Curtain Wall: Reliance -TC IG products, go to and click on Windload Charts. Features and Performance Data Features Overall system dimensions: 2-1/2" x 7-1/4" and 2-1/2" x 6" Front set, inside glazed configuration Optional pressure plate horizontal for exterior glazed spandrel areas or exterior reglazing Captured and SSG (Structural Silicone Glazed) vertical mullions Thermal separation provided through insulating strips on all vertical and horizontal members Accommodates ZS-30E projected and casement vents Factory-painted Kynar 500 /Hylar 5000 finishes, meeting all provisions of AAMA 2605 Factory-anodized finishing Performance Data Air Infiltration: <.06 CFM/SQ FT (6.24 PSF) per ASTM E283 Static Water: 15 PSF per ASTM E331 Dynamic Water: 15 PSF per AAMA Deflection Load: 40 PSF per ASTM E330 Structural Load: 60 PSF per ASTM E330 Seismic: Three levels of deflection per AAMA STC: 35 (1/4" -1/2"- 1/4" glazing) 39 (1/4" laminated - 1/2" - 1/4" laminated glazing) Thermal Performance per AAMA 1503 for: Clear 1" insulating glass - U-factor = CRF frame = 76 1" Sunglass, Low-E, Argon filled: - U-factor = CRF frame = 81 NFRC Certified Thermal Performance Characteristics per AAMA 507 5/2011 S2 P.18

24 curtain wall Curtain Wall: Reliance -TC IG Detail Scale = 1/4 Size H8401 V8401 V8421 V8402 H8407 V8452 V8407 V8457 V8417 Operable Windows H8406 H8405 Spandrel Glass Entrances H8404 Detail numbers (e.g., H8801) reference website detail numbers. For those details not shown in this catalog and for additional information see: This system also available in 6" depth. WW /2" WW /2" WW-108 WW-514 WW-150 WW-110 WW WW /4" H8401 H8405 WW-127 WW-108 WW-518 WW H8404 5/2011 S.2 P Olympic Boulevard Suite 525-East Santa Monica, CA OLDCASTLE ( ) oldcastlebe.com

25 Curtain Wall: Reliance -TC IG WW-520 WW-520 WW-504 curtain wall WW /4" 1/2" 2-1/2" V8401 V8402 V8452 WW-520 WW /2" WW-110 WW WW-145 WW /4" H8407 V8407 WW-504 WW-145 WW-516 WW-110 WW WW-150 H8406 WW-131 V8457 5/2011 S.2 P.20

26 curtain wall Curtain Wall: Reliance -TC IG AN-1 WW-520 WW-341 V8417 WW-228 WW-243 WW /4" WW-170 V8421 5/2011 S.2 P Olympic Boulevard Suite 525-East Santa Monica, CA OLDCASTLE ( ) oldcastlebe.com

27 The Aluminum Framed Monumental Folding/ Paired Panel System The SL45 is a monumental, standard aluminum folding or paired panel system. As a folding system, it is designed to provide an opening glass wall up to 43' wide. With additional paired panels, the width can be virtually unlimited. It is a top-hung system. For benefi ts of all NanaWall systems, see the General Introduction section. For features common to aluminum folding systems, see the Aluminum Folding Systems Introduction. Stacking Configurations for Special Applications Options exist for a variety of confi gurations: all inward-opening panels, all outward-opening panels, some panels opening in and some panels opening out, or center-pivoted panels. Unhinged paired panel options give maximum stacking fl exibility. In addition, angled units of 90º and 135º or segmented units allow designers to create large bay or curved openings. To see these operable wall concepts in action, visit com and click the Animations link. SL45 Introduction Monumental Sized System Monumental sized panels are possible, with frame heights up to 9'6" and panel widths up to 3'7". Heavier and/or thicker glass (such as bullet-resistant laminated glazing) can be used (limitations on panel sizes). Florida Approval The SL45 straight system with panel size of up to 36 x 98 is Florida statewide approved with Product Approval number FL This information can be viewed at oridabuilding.org Rated Swing Panel The Swing panel(s) or Egress door(s) within the system has been engineered for "normal" commercial traffi c and has been independently tested to half a million opening and closing cycles per AAMA 920. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 1

28 SL45 Technical Description General Description The SL45 is a monumental, standard aluminum folding system designed to provide an opening glass wall or storefront up to 43 wide and a paired panel system for unlimited total width; see Maximum Size Chart. The folding system is available in various confi gurations utilizing one to twelve panels or more with unhinged pairs of panels; see elevation drawings. The option exists for swing entry/exit panel(s), but note panel size constraints with a swing panel not hinged to a side jamb. There are many design possibilities; units can be either: all inwardopening or all outward-opening; some panels inward-opening and some panels outward- opening; panels can be centerpivoted; see details in section drawings. Frame and Panels The nominal extruded aluminum frame and panel thickness is 1 3/4 (45 mm); see section drawings. In addition to the choices from the NanaWall Powder Coating Finish Chart, the full range of RAL high gloss and matte powder coatings are available. Anodized and fl ouropolymar kynar painted fi nished are also available; see Aluminum Finish Options in the General Introduction. Panels are pre-assembled, and all pins and screws needed to assemble frames are provided. On a folding pair of panels hinged to a side jamb, the panel hinged to the side jamb is 2 (52mm) narrower in nominal width than the other panels. Besides the standard sill that can match the frame fi nish, various fl ush sills (shown in section drawings) are available as an option in a clear or dark bronze anodized fi nish. Glazing Units can be supplied either glazed with 1/4 (6 mm) single tempered or laminated glass; or 3/4 (20 mm) clear insulating tempered or insulating Low-E tempered glass or other high performing safety glass such as Heat Mirror, special tint, etc., or other glass on request. See Glazing in the General Introduction for other glass thickness possible. Weatherstripping All weatherstripping (consisting of EPDM or brush seals) is provided for sealing between panels and between panel and frame; see section drawings. Sliding/Folding Hardware For sliding and folding each pair of panels, a patented, loadbearing, upper-running carriage is attached to the upper corner of a panel; see section drawings. Attached to the lower corner is a lower-running carriage as a guide. The double pair, twin-tandem, upper-running carriage is constructed to ensure even pressure distribution on all four rollers. Rollers have sealed bearings and are coated with toughened Polyamide to ensure a quiet running and optimal resistance to extreme. Two to fi ve hinges per connection are provided to connect panels together and to connect panels to frames. Finish for zinc die cast hinges would be closest powder coat match to panel profi le. Available as an option are stainless steel hinges. Locking Hardware and Handle Options For each pair of folding panels (except for the pair to be opened fi rst in a unit with no swing panel) and on the secondary swing panel, provided is two point locking hardware consisting of top and bottom Polyamide capped locking rods operated by a 180º turn of a fl at handle on the inside only. If there is a swing panel, there are the following hardware options on the main entry panel: Multi-point Locking. Consisting of lever handles on both sides, a Schlage compatible lockset, lockable latch, deadbolt and rods at the top and the bottom. After turn of key or thumbturn, depression of handles withdraws latch, lifting of engages rods and turn of key or thumbturn engages deadbolt and locks. Deadbolt Lock. Consisting of push/pull handles on both sides with deadbolt(s) operated by a lockset. Turn of key or thumb turn operates lock. Available is a lockset option of having key operation on both sides. To keep the panel closed, a door closer should be fi eld installed, but note that a door closer can only be installed for a swing panel that is attached to the side jamb. No Hardware. For panic hardware to be installed by others, the main entry panel can be supplied with no locking hardware. For a unit with no swing panel, on the folding pair to be opened fi rst, provided is two point locking hardware consisting of top and bottom Polyamide capped locking rods operated by a 180 º turn of an L-shaped handle for an inward opening unit and a fl at handle for an outward opening unit on the inside. In both cases, there will be a fl at handle on the outside. Lockable with a lockset. Turn of key or thumb turn operates lock. Please note that for an outward opening unit, locking from the inside will need to be with a key that may not meet egress requirements. For a unit where locking/handles on the inside only is desired, like in window applications, on all swing panels or pair of folding panels to be opened fi rst, provided is two point locking with a U-shaped handle on the inside only. Handle Finish Schemes: Standard - Stainless steel lever, fl at, and L shaped handles in brushed satin or black titanium fi nish. Optional - Brass lever handles in oil rubbed, satin nickel or white fi nish, fl at handles closest powdercoat match to panel aluminum fi nish and nylon L shaped handles in dark brown, gray or white fi nish. Nylon push/pull handles are in dark brown, gray or white fi nish NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

29 SL45 Performance of the SL45 NanaWall - Testing Results LOW PROFILE SADDLE / FLUSH SILL Type of Test Inward Opening Units Outward Opening Units * Air Infi ltration: ASTM E-283,cfm/ft 1.6 psf (75 Pa): 6.2 psf (300 Pa): 0.78 * Water Penetration: ASTM E-547 Not applicable for fl ush 1.6 psf (75 Pa): 6.2 psf (300 Pa): 0.78 No uncontrolled water 3.76 psf (180 Pa) subject to the following adaptations of the sill in the field by others: 1. Remove the gaskets covering the inner channel. 2. Drill weep holes through the bottom of this channel (about one 1 x ¼ weep slot per panel.) 3. Drill weep holes through the lower front face of the sill to drain water collected to a lower point (about one 3/8 circular weep hole per panel.) Please note that due to varying site requirements and conditions, these sills will not be prepared for drainage by Nana Wall Systems, Inc. If this drainage system is desired, we recommend that a qualified professional construct this system on the project site strictly in accordance with NanaWall instructions and good waterproofing techniques. Note that in some applications drain connections may not be possible. * Structural Load Defl ection ASTM E-330: pass See design windload charts for other sized panels. Note that the structural test pressures were 50% higher than the design pressures. Unit With Reinforced Locking Design Pressure 35 psf (1675 Pa) Design Pressure 35 psf (1675 Pa) Unit With Reinforced Locking Design Pressure 35 psf (1675 Pa) Design Pressure 35 psf (1675 Pa) Thermal Performance: Summary of NFRC U- Factor Computer Simulation Report prepared by Architectural Testing-not NFRC certified Clear (air filled) Low E (air filled) Low E (argon filled) 1/4 Single Glazed Operation / Cycling Performance: AAMA 920 With 20 mm (.78 ) thick Insulated Glass U-Factor For incorporated swing panel 500,000 cycles - pass * Forced Entry Resistance In accordance with AAMA and CAWM 300 requirements. With 20 mm (.78 ) thick Insulated Glass U-Factor *(Excerpts of results of a 9 6 W x 8 6 1/2 H three panel unit with saddle sill tested by Architectural Testing, Inc., Fresno, CA an independent testing laboratory in August 2006) STANDARD SILL Type of Test Inward Opening Units Outward Opening Units * Air Infi ltration: ASTM E-283, cfm/ft 1.57 psf (75 Pa): 1.57 psf (75 Pa): ** Water Penetration: ASTM E-547 No uncontrolled water 1.56 psf (75 Pa). With water spray of 3.1 gallons/sq.ft./min, no uncontrolled water 2.86 psf (135 Pa) No uncontrolled water 1.56 psf (75 Pa). With water spray of 3.1 gallons/sq.ft./min, no uncontrolled water 2.86 psf (135 Pa) * Structural Load Defl ection ASTM E : pass See design windload charts for other sized panels. Note that the structural test pressures were 50% higher than the design pressures. Unit With Reinforced Locking Design Pressure 35 psf (1675 Pa) Design Pressure 35 psf (1675 Pa) Unit With Reinforced Locking Design Pressure 35 psf (1675 Pa) Design Pressure 35 psf (1675 Pa) Thermal Performance: Summary of NFRC U-Factor Computer Simulation Report prepared by Architectural Testing-not NFRC certified Clear (air filled) Low E (air filled) Low E (argon filled) 1/4 Single Glazed Operation / Cycling Performance: AAMA 920 With 20 mm (.78 ) thick Insulated Glass U-Factor For incorporated swing panel 500,000 cycles - pass With 20 mm (.78 ) thick Insulated Glass U-Factor ** (Excerpts of results of a 10 9 W x 8 2 H three panel unit with Standard (Raised) Sill tested by Architectural Testing, Inc., Fresno, CA an independent testing laboratory in November 1999) SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 3

30 SL45 Relationship of Frame, Panel and Glass Daylight Opening Sizes Dimensions in millimeters unless noted. Calculation applies to the standard stiles and rails. Glass dimensions of all panels in a unit are equal, except for glass width of panel(s) that is hinged to either side jamb that has at least one other panel hinged to it. This glass width is 52 mm less than the glass width of other panels. Nominal Panel Height (PH) is defined as Glass Daylight Opening Height (4 5/16 ). Nominal Panel Width (PW) is defined as Glass Daylight Opening Width ( 4 5/16 ). Panel Height is as seen from the inside on an inward opening unit and is as seen from the outside on an outward opening unit. See Cross-Section Details of both stiles of each panel to determine actual Panel Width. With astragals, overlapping, etc., the actual Panel Width not only varies with position of panel in a configuration, but the inside and outside surface widths of each stile may be different. For each configuration, the Frame Width (FW) is the sum of the nominal Panel Width (PW) times the number of panels minus 52 mm x number of panels hinged to side jamb with at least one other panel hinged to it plus a number (N) which is the sum of the side jamb dimensions and dimensions of space between panels in excess of the nominal Panel Width as shown in the Cross-Section Details. Frame Height (FH) SL45 System Standard Sill : Frame Height = Panel Height (4 1/4 ) = Clear Opening Height + 94 (3 11/16 ) Flush/Low Profile Sill: Frame Height = Panel Height (4 11/16 ) = Clear Opening Height (4 1/8 )) Frame Widths for Different Configurations with Majority of Panels Folding to Right (and their Mirror Image Configurations with Majority of Panels Folding to Left). See Maximum Size Charts for size limits. These numbers can be used as a guideline only. Contact NanaWall for the exact calculations for a particular unit. Please note that widths for units with unhinged panels or angle turns will be different. Model 1R Frame Width = 1 x Panel Width + 92 = 1 x Panel Width + 3 5/8 Model 1L1R Frame Width = 2 x Panel Width +100 = 2 x Panel Width /16 Model 2R* Frame Width = 2 x Panel Width = 2 x Panel Width + 1 7/8 Model 3R*, Model 1L2R* Frame Width = 3 x Panel Width = 3 x Panel Width + 2 3/16 Model 4R*, Model 1L3R* Frame Width = 4 x Panel Width = 4 x Panel Width + 2 1/2 Model 2L2R** Frame Width = 4 x Panel Width = 4 x Panel Width + 7/16 Model 5R*, Model 1L4R* Frame Width = 5 x Panel Width = 5 x Panel Width + 2 3/4 Model 2L3R** Frame Width = 5 x Panel Width = 5 x Panel Width + 3/4 Model 3L3R**, Model 2L4R** Frame Width = 6 x Panel Width = 6 x Panel Width + 1 Model 1L5R*, Model 6R* Frame Width = 6 x Panel Width = 6 x Panel Width + 3 1/16 Model 3L4R**, Model 2L5R** Frame Width = 7 x Panel Width = 7 x Panel Width + 1 5/16 Model 1L6R* Frame Width = 7 x Panel Width = 7 x Panel Width + 3 3/8 Model 4L4R**, Model-3L5R**, Model 2L6R** Frame Width = 8 x Panel Width = 8 x Panel Width + 1 5/8 Model 4L5R**, Model-3L6R** Frame Width = 9 x Panel Width = 9 x Panel Width /16 Model 4L6R**, Model 5L5R** Frame Width = 10 x Panel Width = 10 x Panel Width + 2 3/16 Model 5L6R** Frame Width = 11 x Panel Width = 11 x Panel Width + 2 1/2 Model 6L6R** Frame Width = 12 x Panel Width = 12 x Panel Width /16 * One panel that is 52 mm (2 ) narrower than other panels ** Two panels that are 52 mm (2 ) narrower than other panels NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

31 SL45 Maximum Size Chart (with different number of panels) Frame Height of Unit 9 6 (2900) 9 2 (2800) 8 10 (2700) 8 6 (2600) 8 2 (2500) 7 10 ((2400) 7 6 (2300) 7 2 (2200) 6 10 (2100) and below NOTE: English dimensions are approximate. Dimensions in parenthesis are in millimeters A B A B A & B Frame Width of Unit C Units with up to twelve panels are shown on the graph below. With additional unhinged paired panels, virtually unlimited unit widths are possible. Any custom panel size is possible up to the maximum size shown. The total overall unit width is the number of panels multiplied by the individual panel width. As a guide, the table below shows some examples with the number of panels multiplied by selected panel widths. Solid dark line on chart indicates maximum frame height possible for a given maximum frame width with double glazing. Broken line on chart indicates maximum frame height possible for a given maximum frame width with single glazing. A horizontal mullion is needed for a unit with a frame height that is more than 8 6. A. Single or Double Glazed either for confi gurations with folding panels only or for confi gurations with folding panels and a swing door hinged to a side jamb includes Models 1L, 1R, 1L1R, 2R, 1L2R, 4R, 1L6R, 2L2R, 1L4R, 2L4R, 6R, 2L6R,4L4R, 4L6R, 2L, 2L1R, 4L, 4L1R, 4L2R, 6L, 6L1R, 6L2R, 6L4R & 6L6R widths (700) (800) (900) (1000) not possible B. For all confi gurations. Number of Panels in Unit (1400) (1600) (1800) (2000) (2200) widths not (2100) (2400) (2700) (3000) possible (2800) (3200) (3600) (4000) (4400) widths not (3500) (4000) (4500) (5000) possible (4200) (4800) (5400) (6000) (6600) widths not (4900) (5600) (6300) (7000) possible (5600) (6400) (7200) (8000) (8800) widths not (6300) (7200) (8100) (9000) possible (7000) (8000) (9000) (10000) (11000) widths not (7700) (8800) (9900) (11000) possible C. On chart indicates the following additional limitation: no unit with swing panel allowed. Only the following configurations allowed: 2R, 4R, 2L2R, 2L4R, 6R, 2L6R, 4L4R, 4L6R, 2L, 4L, 4L2R, 4L4R, 4L6R, 2L, 4L, 4L2R, 6L, 6L2R, 6L6R. If larger sized panels are needed, please consider the SL70 system. The maximum size limits for double glazed are based on the maximum weight of a panel being 5.5 lbs/sq ft (this weight is based on using standard insulated glass with a net glass thickness of 5/16 (8 mm) or 5/32 (4 mm) for each glass pane). The maximum size limits for single glazed units are based on a glass thickness of 1/4 (6 mm). For other net thicker glass, this maximum size chart will not apply. For confi gurations with no swing panels, the minimum panel width needed is 1'8" (510 mm) (8400) (9600) (10800) (12000) (13200) SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 5

32 SL45 Inward Opening Section Details Detail 1.0 Head Jamb All Cross Sectional Views Are Half Size Detail 22.0 Low Profile Saddle Sill (For resistance against wind driven rain, drain connections by others necessary) EXTERIOR INTERIOR FFH EXTERIOR INTERIOR Detail 23.0 Surface Mounted Interior Sill Frame Height FFH Detail 26.0 Flush Sill (no rating against wind driven rain) Detail 2.0 Standard Sill (Limited water rating against wind driven rain) EXTERIOR INTERIOR FFH EXTERIOR INTERIOR NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

33 All Cross Sectional Views Are Half Size SL45 Inward Opening Section Details Detail 3.0 Panel hinged at right side jamb Detail 3R.0 Panel hinged at left side jamb EXTERIOR INTERIOR Detail 4.0 Swing panel with locking at left side jamb Detail 4R.0 Swing panel with locking at right side jamb EXTERIOR INTERIOR Detail 5.0 Panel with running carriage set meeting left side jamb Detail 5R.0 Panel with running carriage set meeting right side jamb EXTERIOR INTERIOR SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 7

34 SL45 Inward Opening Section Details All Cross Sectional Views Are Half Size Detail 7C.0 & 7RC.0 Folding panels with running carriage set Detail 7.0 & 7R.0 Folding panel with locking (Handle may be on left panel) Detail 8.0, 9.0, & 10.0 Opening Point of Panels Handles only if swing panel(s) Detail 8R.0, 9R.0, & 10R.0 Opening Point of Panels Handles only if swing panel(s) NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

35 All Cross Sectional Views Are Half Size SL45 Outward Opening Section Details Detail 1.1 Head Jamb Detail 22.1 Low Profile Saddle Sill (For resistance against wind driven rain, drain connections by others necessary) FFH Detail 23.1 Surface Mounted Interior Sill Frame Height FFH Detail 26.1 Flush Sill (no rating against wind driven rain) Detail 2.1 Standard Sill (Limited water rating against wind driven rain) FFH SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 9

36 SL45 Outward Opening Section Details All Cross Sectional Views Are Half Size Detail 3R.1 Panel hinged at left side jamb Detail 3.1 Panel hinged at right side jamb EXTERIOR INTERIOR Detail 4.1 Swing panel with locking at left side jamb Detail 4R.1 Swing panel with locking at right side jamb EXTERIOR INTERIOR Detail 5.1 Panel with running carriage set meeting left side jamb Detail 5R.1 Panel with running carriage set meeting right side jamb EXTERIOR INTERIOR NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

37 All Cross Sectional Views Are Half Size SL45 Outward Opening Section Details Detail 7C.1 & 7RC.1 Folding panels with running carriage set Detail 7.1 & 7R.1 Folding panel with locking EXTERIOR INTERIOR (Handle may be on right panel) EXTERIOR Detail 8R.1, 9R.1 & 10R.10 Opening Point of Panels INTERIOR (Handles only if swing panel(s)) EXTERIOR Detail 8.1, 9.1 & 10.1 Opening Point of Panels INTERIOR (Handles only if swing panel(s)) SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 11

38 SL45 Suggested Typical Installation for both Inward and Outward Opening All Cross-Sectional Views are Half Size. Head Jamb See Installation Notes on Next Page Inward Opening Panel Hinged At Right Side Jamb EXTERIOR INTERIOR Rough Opening From Subfl oor Frame Height EXTERIOR Standard Sill INTERIOR Outward Opening Panel Hinged At Right Side Jamb EXTERIOR INTERIOR NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

39 All Cross-Sectional Views are Half Size. Flush Sill (no rating against wind driven rain) SL45 Suggested Typical Installation for both Inward and Outward Low Profile Saddle Sill* EXTERIOR INTERIOR EXTERIOR INTERIOR FFH FFH Surface Mounted Interior Sill Alternate - Standard Sill with Sub-Sill EXTERIOR INTERIOR FFH FFH INSTALLATION NOTES Suggested Typical Installation drawings shown are very general and may not be suitable for any particular installation. Product placement, fasteners, fl ashing, waterproofi ng, sealant, trim and other details for specifi c surrounding conditions must be properly designed and provided by others. Installation Considerations The approximate weight of a panel is 4lbs/ft 2 (single glazing) and 5.5lbs/ft 2 (double glazing). The vertical structural deflection of the header should be limited to the lesser of L/720 of the span and 1/4 under full loads. Structural support for lateral loads (both windload and when the panels are stacked open) must be provided. See Pre-Installation Preparation and Installation Guidelines in the General Introduction and Owner s Manual with installation instructions available for this system. It is recommended that all building dead loads be applied to the header prior to installing the NanaWall. If so and if a reasonable amount of time has been allowed for the effect of this dead load on the header, then only the building s live load can be used to meet the above requirements of L/720 or 1/4. If not, both the dead and live loads need to be considered. *FOR LOW PROFILE SADDLE SILL: For resistance against wind driven rain, the following is recommended by others 1. Remove the gasket covering the inner channel. 2. Provide necessary weepholes at the bottom of the channels and on the outside face of the sill. 3. Make necessary drain connections. Ask NanaWall for a detailed drawing. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 13

40 SL45 Elevation and Section Details All Cross Sectional Views Are Half Size As a guide, in low wind areas, a 3 high transom is possible with a 12 wide unit with Details 36 and 37. Note that the Support Profile must be attached to the adjacent wall. For other applications, a structural beam will be necessary between folding unit and transom. Detail 36 Support profile between fixed transoms and SL45 unit for certain limited applications depending on size, configuration and structural loading Detail 37 Support profile between fixed windows and SL45 unit for certain limited applications depending on size, configuration and structural loading Typical Elevation: I-3L with fixed bottom windows Typical Elevation: I-3L with fixed transoms Typical Kickplate Typical Mullion Profile Profile with Single Glazing Simulated Divided Lites Muntin with Spacer Bar EXTERIOR INTERIOR NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

41 SL45 Design Windload Chart Unit with Reinforced Locking 76 (Derived From Comparative Analysis) Test Unit Size: 9 6 W x 8 6 1/2 H (3 panels) Please note that some jurisdictions 70 may limit the use of these charts or may not accept them at all. Design 68 pressures and/or sizes may be restricted to what was tested. For 66 Florida approved products, please see detailed FL Evaluation Report for restrictions Please also note that chart is only 60 applicable for units with referenced Nana Wall supplied locking. Positive and Negative Design Pressures for both inward and outward opening units Allowable Design Wind Loading - PSF Unit Width Divided by Number of Panels Panel Height See Maximum Frame Size Chart for Possible Sizes SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 15

42 SL45 Guide Specifications - Section NanaWall SL45- Monumental Aluminum Framed Folding/Paired Panel System PART 1 - GENERAL 1.01 SUMMARY A. Section Includes: Sliding/folding aluminum and glass door system, including aluminum frame, threshold, panels, sliding/folding and locking hardware, weather stripping, glass and glazing; designed to provide an opening glass wall, with sizes and configurations as shown on drawings and specified herein, NanaWall SL45, Monumental Aluminum Framed Folding/ Paired Panel System as supplied by NANA WALL SYSTEMS, INC REFERENCES A. American Architectural Manufacturers Association (AAMA): 1. AAMA 611, Voluntary Specification for Anodized Architectural Aluminum. 2. AAMA 2604 and 2605, Voluntary Specifications, Performance Requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels. 3. AAMA 1304, Voluntary Specification for Forced Entry Resistance of Side-Hinged Door Systems 4. AAMA 920, Operation / Cycling Performance B. American National Standards Institute (ANSI): 1. ANSI Z97.1, Safety Performance Specifications and Methods of Test for Safety Glazing Material Used In Buildings. C. American Society for Testing and Materials (ASTM): 1. ASTM E 283, Test Method for Rate of Air Leakage through Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference. 2. ASTM E 330, Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference. 3. ASTM E 547, Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Doors by Cyclic Static Air Pressure Differential. 4. ASTM E 331, Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Cur tain Walls by Uniform Static Air Pressure Difference. D. Consumer Product Safety Commission (CPSC): 1. CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials. E. National Fenestration Rating Council (NFRC): 1.03 SUBMITTALS 1. NFRC 100, Procedure for Determining Fenestration Product Thermal Materials. A. Detail Drawings: Indicate dimensioning, direction of swing, configuration, swing panels, typical head jamb, side jambs and sill details, type of glazing material, and handle height. B. Product Data: Manufacturer s literature including independently tested data listing performance criteria and Owner s Manual with installation instructions. C. Contract Closeout Submittal: Submit Owner s Manual from manufacturer. Identify with project name, location and completion date, type and size of unit installed QUALITY ASSURANCE A. Manufacturer: Provide complete, precision built, engineered, pre-fitted unit by a single source manufacturer with at least 25 years experience in providing folding/sliding door systems for large openings in the North American market. 1. The manufacturer must have a quality management system registration to the ISO 9001: 2008 standard. B. Performance Requirements: Provide from manufacturer that has independently tested typical units. Testing results to include air infiltration in accordance with ASTM E 283, water penetration in accordance with ASTM E 331/E 547, structural loading in accordance with ASTM E 330, forced entry in accordance with AAMA and CAWM and Operation / Cycling Performance of Swing Panel in accordance with AAMA NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

43 Guide Specifications - Section SL45 SPECIFIER S NOTE: Air infiltration and water penetration testing results can only be applicable if the unit matches the test unit in the direction of opening and the type of sill. Structural load testing results are only applicable for the test unit size and type of locking and rods. (Comparative analysis charts published by manufacturer show which panel sizes (if any) would meet structural loading design pressures specifically required for the project. Check for limitations on the use of these charts in the jurisdiction of the project). Forced entry testing results are only applicable for the test unit type of locking. See manufacturer s latest published data. C. Thermal Performance U factor: Unit to be simulated in accordance with NFRC 100, shown in manufacturer s latest published data for the specified product. D. Installer Qualifications: Installer experienced in the installation of manufacturer s products or other similar products for large openings. Installer to provide reference list of at least 3 projects of similar scale and complexity successfully completed in the last 3 years WARRANTY A. Provide manufacturer s standard warranty against defects in materials and workmanship. B. Warranty Period: Ten years for rollers and for seal failure of insulated glass supplied. For all other components, one year (two years if unit is installed by manufacturer s certified trained installer) from date of delivery by manufacturer SITE CONDITIONS, DELIVERY, STORAGE AND HANDLING A. In addition to general delivery, storage and handling requirements specified in Section 01600, comply with the following: 1. Deliver materials to job site in sealed, unopened cartons or crates. Protect units from damage. Store material under cover, protected from weather and construction activities. PART 2 PRODUCTS 2.01 SUPPLIER A. NANA WALL SYSTEMS, INC. - SL Meadow Creek Drive, Corte Madera, CA Toll Free: (800) Telephone: (415) Fax: (415) Website: info@nanawall.com B. Other suppliers equal to the specified product must submit substitution request two weeks before bid for prior approval MATERIALS A. Frame and Panels: From manufacturer s standard profiles, provide head track, side jambs, and panels with dimensions shown on drawings. 1. Provide panels with: Standard one lite [OR with horizontal mullion(s) at specified height(s) from the bottom of the panel] [OR with simulated divided lites in pattern as shown on drawings]. 2. Provide standard bottom rail [OR manufacturer s standard kickplate with height specified]. 3. Aluminum Extrusion: Extrusions with nominal thickness of.078 (2.0 mm). Alloy specified as AIMgSi0.5 with strength rated as 6063-T5 or F-22 (European standard). Anodized conforming to AAMA 611, powder coated conforming to AAMA 2604 and PVDF Kynar conforming to AAMA Aluminum Finish: Select from NanaWall Powder Coating Finish Chart SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 17

44 SL45 Guide Specifications - Section B. Glass: [OR dark bronze anodized] [OR clear anodized] [OR select from range of flouropolymar kynar painted finish] [OR select from range of RAL high gloss powder coated finished available from manufacturer] [OR select from range of RAL matte powder coated finished available from manufacturer] [OR custom finish]. 1. All glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR Provide manufacturer s standard glass with dry glazing with glass stops on the inside only: 1/4 (6 mm) tempered [OR 1/4 (6 mm) laminated] [OR 3/4 (20 mm) insulating clear safety] [OR 3/4 (20 mm) insulating argon filled Low-E safety] [OR other glass available from manufacturer, including glass with other total thickness]. 2. For insulated units, provide manufacturer s standard silver gray [OR dark bronze] glass spacers. Provide without capillary tubes [OR with capillary tubes]. C. Locking Hardware and Handles: 1. Main entry panel: On the main entry panel for models with a swing panel, provide manufacturer s standard lever handles on the inside and outside, a Schlage compatible lock set with lockable latch, multi-point locking with a dead bolt and rods at the top and bottom on primary panel only. Rods to be concealed and not edge mounted. After turn of key or thumbturn, depression of handles withdraws latch. Lifting of handles engages rods and turn of key or thumb turn engages deadbolt and operates lock. If there is a secondary swing panel, provide two point locking with flat handles on inside only for the secondary swing panel. Stainless steel lever handles in a titanium black finish [OR stainless steel lever handles in a brushed satin finish] [OR oil rubbed bronze solid brass lever handles] [OR satin nickel solid brass lever handles] [OR white solid brass lever handles] [OR on the main entry panel for models with a swing panel, provide manufacturer s push/pull handles with separate lock set and dead bolt. Push-pull handles in a brown nylon finish [OR push-pull handles in a gray nylon finish] [OR push-pull handles in a white nylon finish] SPECIFIER S NOTE: This option is recommended with a door closer, but note that in order to slide the swing panel, the door closer will need to be disengaged if the swing panel is not attached to a side jamb.] [OR on the main entry panel for models with a swing panel, no hardware or locking to be provided by the manufacturer, but with field installed panic device by others.] [OR on both entry panels for models with a pair of swing panels, no hardware or locking to be provided by the manufacturer, but with field installed panic devices on both panels by others.] [OR on main entry pair of panels on inswing models without a swing panel, provide manufacturer s standard L-shaped handle on the inside, flat handle on the outside and lock set with profile cylinder. Operation of lock set is by turn of key from the outside and with a thumbturn from the inside with a two point locking hardware operated by 180º turn of the handle.] Stainless steel L shaped handles in a titanium black finish [OR stainless steel L shaped handles in a brushed satin finish] [OR L shaped handles in a brown nylon finish] [OR L shaped handles in a gray nylon finish] [OR L shaped handles in a white nylon finish [OR on main entry pair of panels on outswing models without a swing panel, provide manufacturer s standard flat handle on the inside and on the outside and a lock set with a profile cylinder. Operation of NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

45 Guide Specifications - Section SL45 lock set is by turn of key from the outside and from the inside with a two point locking hardware operated by 180º turn of the handle. SPECIFIER S NOTE: Key operation from the inside may not meet egress requirements.] [OR on main entry panel, provide manufacturer s standard flat handle on inside only with concealed two point locking hardware operated by 180 degree turn of handle. SPECIFIER S NOTE: Note that with this option, the main entry panel is operable from inside only and that there is no latch.] SPECIFIER S NOTE: Note that other compatible lever, L shaped and push-pull handle styles and finishes are available from other suppliers. 2. On all other secondary swing panels and pairs of folding panels, provide manufacturer s standard flat handles [OR removable custodial handles] and concealed two point locking hardware operated by 180 degree turn of handle between each pair. Face applied flush bolt locking will not be allowed (except for units with paired handles). 3. Flat handle finish: Stainless steel in a titanium black finish [OR stainless steel in a brushed satin finish] [OR closest powder coat match to aluminum profile finish] 4. Provide handle height centered at 41 3/8 [OR as specified] from bottom of panel. 5. Aluminum locking rods with fiber glass reinforced polyamide end caps at top and bottom. Rods to have a stroke of 15/16 (24 mm). 6. If there are more than one unit, keyed alike [OR keyed differently]. D. Sliding/Folding Hardware: Provide manufacturer s standard combination sliding and folding hardware with top and bottom tracks. 1. For each pair of folding panels, provide cardanic, independently suspended, four wheeled coated with fiber glass reinforced polyamide upper running carriage and lower guide carriage. 2. Provide manufacturer s standard zinc die cast powder coated hinges that are closest to match to finish of frame and panels [OR stainless steel hinges]. Provide stainless steel security hinge pins with set screws. 3. Adjustment: Provide system capable of specified amount of adjustments without removing panels from tracks without needing to remove panels from tracks, 1/16 (1.5 mm) in width per hinge. E. Other Components: 1. Threshold: Provide standard sill in the same finish as panel finish [OR clear anodized standard sill] [OR dark bronze anodized standard sill] [OR clear anodized Surface Mounted Interior Sill] [OR bronze anodized Surface Mounted Interior Sill] [OR clear anodized flush sill] [OR dark bronze anodized flush sill] [OR clear anodized low profile saddle sill] [OR dark bronze anodized low profile saddle sill]. Cover plate over the sill will not be allowed 2. Weather stripping: Provide manufacturer s standard double layer EPDM or brush seals with a two layer polyamide fin at both the inner and outer edge of door panels or on frame for sealing between panels and between panel and frame. Single layer weather stripping will not be allowed 3. Provide stainless steel screws for connecting frame components FABRICATION A. Use extruded aluminum frame and panel profiles, corner connectors and hinges, sliding and folding hardware, lock- SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE NanaWall Systems 19

46 SL45 Guide Specifications - Section ing hardware and handles, glass and glazing and weather stripping as specified herein to make a folding glass wall. Factory pre-assemble as is standard for manufacturer and ship with all components and installation instructions. B. Sizes and Configurations: See drawings for selected custom dimensions within maximum frame sizes possible as indicated in manufacturer s literature. See drawings for selected number of panels and configuration. Inward [OR outward] [OR center pivot] [OR inward / outward combination unit] [OR Contact NanaWall for other stacking options and layouts] opening unit. On configurations with a pair of swing panels, looking from inside, primary swing panel on the left [OR right] 2.04 ACCESSORIES (Edit for project requirements.) A. Provide the NanaScreen, a series of vertical, collapsible, pleated screen panels. Provide pleated screen material with floor tracking chain with 1/4 (6 mm) floor track. See drawings for selected number of panels and configuration. Provide aluminum top track, side jambs, and vertical struts: White powder coated [OR clear anodized] [OR dark bronze anodized] [OR select from range of RAL powder coated fi nishes available from manufacturer] NanaScreen installation within opening [OR extended beyond opening] B. Provide other side lites, transoms, corner posts, or single or double doors as per drawings provided. PART 3 - EXECUTION 3.01 ERECTION A. Because of the large dimensions involved and the weight and movement of the panels, verify the structural integrity of the header such that the deflection with the live and dead loads is limited to the lesser of L/720 of the span and 1/4 (6 mm). Structural support for lateral loads (both wind load and eccentric load when the panels are stacked open) must be provided. It is recommended that all building dead loads be applied to the header prior to installing the NanaWall. If so and if a reasonable amount of time has been allowed for the effect of this dead load on the header, then only the building s live load can be used to meet the above requirements of L/720 or 1/4 (6 mm). If not, both the dead and live loads need to be considered. B. Examine surfaces of openings and verify dimensions; verify rough openings are level, plumb, and square, with no unevenness, bowing, or bumps on floor. C. Installation of units constitutes acceptance of existing conditions INSTALLATION A. Install frame in accordance with manufacturer s recommendations and installation instructions. Properly flash and waterproof around the perimeter of the opening. B. Installer to provide appropriate anchorage devices and to securely and rigidly fit frame in place, absolutely level, straight, plumb and square. Install frame in proper elevation, plane and location, and in proper alignment with other work. C. If necessary, provide drain connections from lower track. D. Install panels, handles and lock set in accordance with manufacturer s recommendations and installation instructions. E. If necessary, adjust hardware for proper operation. F. Accessories: Screens; install in accordance with screen manufacturer s recommendations and installation instructions. END OF SECTION DISCLAIMER: Nana Wall Systems, Inc. takes no responsibility for product selection or application, including, but not limited to, compliance with building codes, safety codes, laws, or fitness for a particular purpose. The guide specifications is not intended to be verbatim as a project specification without appropriate modifications for the specific use intended and the particular requirements of a specific construction project NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

47 5/10/2011 Home Commercial Sliders Residential Sliders Screening About Our Products About Us/Contact Us Insta Commercial Sliders Trophy Case Doors Service Windows/Pass Thru's Exterior Sliders Trophy Case Doors Interior Doors/Pocket Doors Installed in schools throughout the Southwest Narrow stiles / interlocks provide maximum viewing Each panel slides independently behind other panels Flush-mount hardware Cylinder key locks (keyed alike) Dual Tandem rollers provide easy opening Can be configured with 2, 3 or 4 panels. 2 or 4 panel configurations are built with standard 4 frame 3-Panel configurations built with 3 rail system on 6 frame Metal-Craft Products Company All rights reserved.

48 HORIZONTAL CROSS-SECTION & DETAILS: VERTICAL CROSS-SECTION & DETAILS: OX SERVICE WINDOW I INT. SILL PROFILE I SINGLE GLAZE PG 1 OF 1

49 I SERVICE WINDOW I ASSEMBLY GUIDE PG 1 OF 5

50 I EXTERNAL FRAME ASSEMBLY AND PREPARATION I PG 2 OF 5

51 I SLIDING AND FIXED WINDOW ASSEMBLY I PG 3 OF 5

52 I INSTALLATION OF WINDOWS INTO EXTERNAL FRAME I PG 4 OF 5

53 I SECURING OF FIXED WINDOW TO EXTERNAL FRAME I PG 5 OF 5

54 Solar Shelf by Oldcastle BuildingEnvelope Introducing the Solar Shelf, an architectural light shelf for use with our CW-250 and Reliance Curtain Wall products. The system is field installed onto the interior of the curtain wall to deflect daylight deeper into the building, thus reducing demand for artificial lighting and associated energy costs. Solar Shelf is comprised of extruded aluminum struts with.090 panels set Solar Shelf between a wall mount and continuous cover. The Solar Shelf may be ordered in depths up to 30" and with three standard interior covers or custom covers to fit your project requirements. When used in conjunction with Solar Eclipse sunshades, additional energy savings can be realized. Features Overall System Dimensions: 2-1/2" height with a maximum depth of 30" Easy installation utilizing extruded components and aluminum panels Field or Shop fabricated All extrusions and panels may be ordered in factory anodized or painted Kynar 500 /Hylar 5000 finishes, meeting all provisions of AAMA Shear block and screw spline assembly Standard or Custom interior covers and end caps May be installed on CW-250 or Reliance Curtain Walls Kynar 500 is a registered trademark of Atofina Hylar 5000 is a registered trademark of Ausimont USA, Inc. Drawings 2425 Olympic Boulevard, Suite 525-East Santa Monica, CA OLDCASTLE ( ) oldcastlebe.com

55 Solar Eclipse Sunshades by Oldcastle BuildingEnvelope Solar Eclipse sunshades

56 Solar Eclipse sunshades Solar Eclipse TM Systems Mounting Options The Solar Eclipse Sunshade Series does more than merely provide shade. This advanced system reduces energy consumption while providing occupants with comfortable interior environments. Design options include outriggers and brackets in an assortment of sizes and styles and louvers that can be radius, diamond or airfoil in shape to suit a building s architectural requirements. With fascia profiles that include rounded, square or airfoil, Solar Eclipse is a highly flexible system that can be tailored to the individual needs of the customer. Mix and match these pre-engineered sunshade elements to create signature designs that provide a customized appearance. Radius Circular Airfoil (Large) Rectangular Airfoil (Small) Square Diamond "Z" 2425 Olympic Boulevard, Suite 525-East Santa Monica, CA OLDCASTLE ( ) oldcastlebe.com

57 Emmis Communications Corp. - Indianapolis, IN Architect: RATIO Architects Inc. Glazing Contractor: ASI Limited Custom Fabrication: Ornamental Sill Flashing, Fascia Panels, Ornamental Tower a n o d i z e d A L u m i n u m PAC 500 Bronze Anodized Aluminum Petersen Aluminum Corporation s line of PAC 500 anodized finishes features a wide range of architectural bronzes and black. The PAC 500 finish is accomplished through a progressive electrolytic process. The metal is first anodized in a sulfuric acid bath. The material then passes through an electrically charged bath of cobalt mineral salts. The finishing process is completed as the metal passes through a sealing tank. A complete range of bronze shades and black can be achieved through variation of the current through the coloring tank. PAC 500 is highly resistant to ultra-violet light. The coil anodizing capability allows us to hold extremely tight control over color range, making PAC 500 the finish of choice for curtain wall, storefront and batten roofing applications where an anodized finish is desired. With anodized finishes, a color variance is to be expected from batch to batch. To minimize the color variance, please order enough sheet or coil to complete the project. anodized availability chart PAC 500 Bright Clear Bright Gold Champagne Light Bronze Medium Bronze Dark Bronze Black PAC 300 Clear PAC 300 Clear Anodized Aluminum PAC 300 Clear Anodized Aluminum consists of anodized quality 5005-H34 aluminum sheet, giving a.0003 thick clear anodized coating. Coil anodizing allows for exceptional control over uniformity of appearance. PAC 300 anodized aluminum is stocked in gauges P A C - C L A D W W W. P A C - C L A D. C O M

58 Our Lady of Good Counsel High School - Olney, MD Owner: Roman Catholic Archdiocese of Kensington Architect: DCMM Architects General Contractor: Coakley Williams Construction, Inc. Roofing Contractor: Interstate Corporation Color: Sierra Tan Profile: Snap-Clad Panels F L A T A N D C o i L s t o C K In addition to offering the industry s widest selection of Kynar finishes in steel and aluminum, Petersen Aluminum also offers pre-painted aluminum and mill finish sheet and coil in a variety of gauges. With state-of-the-art cut to length and slitting equipment, Petersen can provide flat and coil stock to the most exacting specifications. PAC Painted ACryLIC Sheet Dark Bronze, Medium Bronze, White, Blue, Yellow, Brown, Black and Red painted sheet is stocked for immediate delivery. PAC pre-painted aluminum may be sheared and formed over a 1-1/2 to 2 T bend radius. Life expectancy is 10 years plus. This material is highly suitable for a wide range of applications, including signage and the race car industry. No warranty is available on this product. MiLL Finish Anodizing quality 5005-H34, as well as 3003-H14, is stocked in gauges.032 to.125 for all applications that require fabrication and post-finishing. Textured Sheet Most finishes stocked by Petersen are available in an E-5 stucco embossed pattern. Gauges.063 and over are not available in this pattern. Samples are available on inquiry. Petersen also stocks in limited gauges and finishes perforated sheets for projects requiring ventilation. Check with the local factory for perforated sheet options. 36

59 g e n e r A L c o n s i d e r a t i o n s GenerAL Considerations The following is a summary of conditions and considerations that we consider important to the design and specification of PAC-CLAD PANEL projects. For more specific information concerning your projects, please contact us directly on our technical service line: PAC-CLAD. We will gladly provide you with any additional information you may need. Pitch TITE-LOC Panels are designed for a roof pitch of 1/2:12 or greater. SNAP-CLAD Panels have been designed to be installed on applications as low as 2:12 pitch. Integral Panels, Redi-Roof Panels and Snap-On Panels have been designed for a minimum 3:12 pitch. Greater pitch may be required in snow country and in areas of extreme climate conditions. Finishes PAC-CLAD PANELS are available as standard with a full strength Kynar 500 or Hylar 5000 finish. Please refer to the color charts on pages 7 & 8 for color selection. Samples and photo-accurate color charts are available for your assistance. Other finishes available include PAC 300 Clear and PAC 500 Bronze coatings; Siliconized polyester and acrylics. SpeciAL Colors Special colors are available for most applications of greater than 10,000 square feet and may be applied to either aluminum or G-90 galvanized steel. Contact Petersen for information concerning relative costs and availability. InstALLAtion Special care must be taken to insure that panels are installed over a flat substrate. For roofing applications, panels typically must be installed over 5/8 or 3/4 plywood decking with ice and water shield or 30# roofing felt (minimum) horizontally overlayed from the eave to ridge. It is recommended that clips be installed on 18 centers for all applications except Snap-Clad, Tite-Loc Plus and Tite-Loc (consult specific UL Construction assemblies for clip spacing). Consult a local architect/engineer for requirements of local codes and conditions. ACCessories Most applications require additional metalwork including fascia, storefront trim, copings, gravel stops, downspouts, etc. Such metalwork may be specified for fabrication by manufacturer or for fabrication from flat sheet as provided by manufacturer. Flashings fabricated from PAC-CLAD flat sheet are fully covered under Petersen s 20 year finish warranty. PAC-CLAD flat sheet provides an exact color match to PAC-CLAD Panels. Lengths All panels are custom cut-to-length before roll-forming and are available in lengths up to 64. See specific product pages for maximum panel lengths. Minimum length is 4-0. Lengths are accurate to 1/4. Custom cut-to-length is available at no up-charge and helps to improve project economy. Consult factory for longer lengths. Pa n e l W i d t h s Most of our PAC-CLAD Panels are available in non-standard on-center dimensions. Contact Petersen Aluminum for product availability and cost. PAC-CLAD panel standard widths are nominal and could vary. Fire ratings PAC-CLAD Panels have been evaluated by Underwriter s Laboratories for inclusion in a variety of fire-rated P-Assemblies and are classified in section CETW of the UL Fire Resistance Directory - Vol. 1. Several panel assemblies have been evaluated as Class A fire rated. Contact PAC for complete information on components and assemblies. Oil Canning All Petersen material is prime quality aluminum and G-90 galvanized steel. All materials used are specified for rollforming applications and are, as such, stretcher and tension leveled. Panels are inspected in the plant for flatness before shipment. Job-site conditions such as temperature variation, unlevel substrate and/or improper installation may aggravate this condition. Oil canning does not affect the finish or structural integrity of the panel and is therefore not cause for rejection. Warranty A full twenty year finish warranty is available covering cracking, peeling and color fade on all PAC-CLAD applications. PAC-CLAD is a full Kynar 500 or Hylar 5000 finish and is, therefore, the highest quality 20 year non-prorated finish available. Full test results and SPEC-DATA information are available from Petersen. Storage Materials should be stored in a clean, dry place. Suitable facilities for storage and protection of material should be provided at the job-site. Store materials out of traffic areas to prevent dents, bending, abrasion, etc. Limitations On LiABility Neither Petersen Aluminum Corporation nor its customer shall be liable for special, indirect, or consequential damages. The liability of Petersen Aluminum Corporation in the event of the sale of its products shall be limited to replacement of any defective or nonconforming products or refund of the purchase price. CoastAL APPLiCAtions PAC recommends that prefinished aluminum with stainless steel clips should be used in lieu of prefinished steel P A C - C L A D W W W. P A C - C L A D. C O M

60 PRODUCT DATA Joint Sealants SONOLASTIC NP 1 One-component, elastomeric, gun-grade polyurethane sealant Description NP 1 is a one-component, highperformance, nonpriming, gun-grade, elastomeric polyurethane sealant. It requires no mixing and typically requires no priming to bond to many materials, including concrete and masonry. Yield See page 3 for charts. Packaging 300 ml (10.1 fl oz) cartridges, 30 cartridges per carton 20 fl oz (590 ml) ProPaks, 20 per carton For color availability in bulk packaging, call Customer Service. Color White, off-white, limestone, anodized aluminum, stone, tan, aluminum gray, precast gray, medium bronze, special bronze, redwood tan, ash brown and black. Shelf Life Cartridges and ProPaks: 1 year when properly stored. Storage Store in original, unopened containers away from heat and direct sunshine. Storing at elevated temperatures will reduce the shelf life. Features Benefits Ready to use Requires no mixing; reduces labor costs Joint movement capability ±35% Provides excellent flexibility for keeping moving joints tight Easy to gun and tool Speeds application and makes neater joints Available in cartridges, Reduces jobsite waste, lowers disposal costs 20 ounce ProPaks, and in bulk Twelve standard colors Matches common substrates No primer required for most Lowers installation costs construction materials Weather resistant Produces long-lasting weather-tight seals Wide temperature-application range Suitable for all climates Compatible with nonrigid coatings May be painted Superior holding power Long-lasting roof tile instalation UL listed Passes 4 hour, 4 inch, fire and hose stream test when used with Ultra Block or mineral wool Suitable for water immersion Documented performance in wet areas Low VOC content Meets VOC requirements in all 50 states Where to Use APPLICATION Expansion joints Curtain wall construction Panel walls Precast units Aluminum and wood window frames Roofing Fascia Parapets Structural components Vinyl siding Wastewater treatment plants Dams Spillways and storm drains Wetwells and manholes LOCATION Interior and exterior Above and below grade Immersed in water SUBSTRATE Concrete Masonry Aluminum Wood Clay & concrete roof tiles 29

61 SONNEBORN PRODUCT DATA NP 1 Technical Data Composition Test Data Sonolastic NP 1 is a one-component moisturecuring polyurethane. PROPERTY RESULTS TEST METHODS Movement capability, % ±35 ASTM C 719 Compliances Tensile strength, 350 (2.4) ASTM D 412 ASTM C 920, Type S, Grade NS, Class 35, Use psi (MPa) NT, M, A, G*, O** and I Federal Specification TT-S C, Type II, Class A Corps of Engineers CRD-C- 541, Type II, Class A Canadian Specification CAN/CGSB M87, Classification MCG-2-25-A-N, No USDA compliant for use in meat and poultry areas Underwriters Laboratories Inc. classified (fire resistance only) Canadian approval for use in establishments that Tear strength, pli Ultimate elongation at break, % Rheological, (sag in vertical displacement) at 120 F (49 C) Extrudability, 3 seconds Hardness, Shore A At standard conditions After heat aging (max Shore A: 50) Weight loss, after heat aging, % No sag Passes ASTM D 1004 ASTM D 412 ASTM C 639 ASTM C 603 ASTM C 661 ASTM C 792 handle food Cracking and chalking, SWR Institute validated after heat aging None ASTM C 792 ISO F-25LM Tack-free time, hrs, Passes ASTM C 679 * NP1 not recommended for application on glass. (maximum 72 hrs) ** Refer to substrates Where into Use. INSTITUTE SEALANT VALIDATION Typical Properties PROPERTY VALUE Service temperature -40 to 180 range, F ( C) (-40 to 82) Shrinkage SEALANT WATERPROOFING & RESTORATION INSTITUTE Issued to: BASF Building Systems Product: Sonolastic NP-1 C719: Pass 3 Ext:+35% Comp:-35% Substrate: Aluminum, Mortar, Granite [mortar and granite substrates primed with primer No. 733] C661: Rating 25 Validation Date: 6/20/06-6/19/11 No. 606-NP1611 Copyright 2006 None Stain and color change Passes ASTM C 510 (no visible stain) Bond durability,* on glass, Passes ASTM C 719 aluminum, and concrete ±35% movement Adhesion* in peel, pli (min. 5 pli) 30 ASTM C 794 Adhesion* in peel after Passes ASTM C 794 UV radiation through glass (min. 5 pli) Artificial weathering, Passes ASTM C 793 Xenon arc, 250 hours Artificial weathering, No surface cracking ASTM G 26 Xenon arc, 3,000 hours Water immersion, 122 F (50 C) Passes 10 weeks with ASTM C 1247 movement cycling *Primed for water immersion dictated by ASTM C 920. Concrete and aluminum primed with 733; glass primed with 766. Test results are typical values obtained under laboratory conditions. Reasonable variations can be expected. 29.2

62 SONNEBORN PRODUCT DATA NP 1 Yield LINEAR FEET PER GALLON* JOINT DEPTH JOINT WIDTH (INCHES) (INCHES) 1/4 3/8 1/2 5/8 3/4 7/8 1 1/ / / *One gallon equals approximately 12 cartridges or 6 ProPaks METERS PER LITER JOINT DEPTH JOINT WIDTH (MM) (MM) How to Apply Joint Preparation 1. The number of joints and the joint width should be designed for a maximum of ±35% movement. 2. The depth of the sealant should be 1/2 the width of the joint. The maximum depth is 1/2 (13 mm) and the minimum is 1/4 (6 mm). Refer to Table 1. TABLE 1 Joint Width and Sealant Depth 3. In deep joints, the sealant depth must be JOINT WIDTH, SEALANT DEPTH IN (MM) AT MIDPOINT, IN (MM) 1/4 1/2 (6 13) 1/4 (6) 1/2 3/4 (13 19) 1/4 3/8 (6 10) 3/4 1 (19 25) 3/8 1/2 (10 13) 1 1-1/2 (25 38) 1/2 (13) controlled by Closed-Cell Backer-Rod or Soft Backer- Rod. Where the joint depth does not permit the use of backer-rod, a bondbreaker (polyethylene strip) must be used to prevent three-point bonding. 4. To maintain the recommended sealant depth, install backer-rod by compressing and rolling it into the joint channel without stretching it lengthwise. Closed-Cell Backer-Rod should be about 1/8" (3 mm) larger in diameter than the width of the joint to allow for compression. Soft Backer-Rod should be approximately 25% larger in diameter than the joint width. The sealant does not adhere to it, and no separate bondbreaker is required. Do not prime or puncture the backer-rod. Surface Preparation Surfaces must be structurally sound, fully cured, dry, clean, free of dirt, moisture, loose particles, oil, grease, asphalt, tar, paint, wax, rust, waterproofing or curing and parting compounds, and membrane materials. CONCRETE, STONE, AND OTHER MASONRY Clean by grinding, sandblasting, or wire brushing to expose a sound surface free of contamination and laitance. WOOD New and weathered wood must be clean and sound. Scrape away loose paint to bare wood. Any coating that cannot be removed must be tested to verify adhesion of sealant or to to determine an appropriate primer. METAL Remove scale, rust, and coatings from metal to expose a bright white surface. Remove protective coatings as well as any chemical residue or film. Aluminum window frames are frequently coated with a clear lacquer that must be removed before the application of NP 1. Any coating that cannot be removed must be tested to verify adhesion of sealant or determine an appropriate primer. Remove any other protective coatings or finishes that could interfere with adhesion. Priming 1. NP 1 is generally considered a nonpriming sealant, but special circumstances or substrates may require a primer. It is the user s responsibility to check the adhesion of the cured sealant on typical test joints at the project site before and during application. Refer to product data sheet on Primer 733 or 766, and consult Technical Services for additional information. 2. For immersion applications, Primer 733 must be used. 3. Apply primer full strength with a brush or clean cloth. A light, uniform coating is sufficient for most surfaces. Porous surfaces require more primer; however, do not overapply. 4. Allow primer to dry before applying NP 1. Depending on temperature and humidity, primer will be tack free in minutes. Priming and sealing must be done on the same work day. Application 1. NP 1 comes ready to use. Apply by professional caulking gun. Do not open cartridges, sausages, or pails until preparatory work has been completed. 2. Fill joints from the deepest point to the surface by holding a properly sized nozzle against the back of the joint. 3. Dry tooling is recommended. DO NOT use soapy water when tooling. Tooling results in the correct bead shape, a neat joint, and maximum adhesion. 4. For roof tile applications apply a bead of Sonolastic NP 1 sufficient to make a bond between two tiles on the upper surface of the down slope tile. Install the upslope tile & press into the sealant bead to ensure good contact between the sealant and both tiles. Clean Up 29.3

63 SONNEBORN PRODUCT DATA NP 1 1. Immediately after use, clean equipment with Reducer 990 or xylene. Use proper precautions when handling solvents. 2. Remove cured sealant by cutting with a sharp-edged tool. 3. Remove thin films by abrading. Curing Time The cure of NP 1 varies with temperature and humidity. The following times assume 75 F (24 C), 50% relative humidity, and a joint 1/2" width by 1/4" depth (13 by 6 mm). Skins: overnight or within 24 hours Functional: within 3 days Full cure: approximately 1 week Immersion service: 21 days For Best Performance Do not allow uncured NP 1 to come into contact with alcohol-based materials or solvents. Do not apply polyurethane sealants in the vicinity of uncured silicone sealants or uncured Sonolastic 150 or 150 Tint Base. NP 1 should not come in contact with oil-based caulking, uncured silicone sealants, polysulfides, or fillers impregnated with oil, asphalt, or tar. Protect unopened containers from heat and direct sunshine. In cool or cold weather, store container at room temperature for at least 24 hours before using. When NP 1 is to be used in areas subject to continuous water immersion, cure for 21 days at 70 F (23 C) and 50% relative humidity. Allow longer cure times at lower temperatures and humidities. Always used Primer 733. Do not use in swimming pool or other submerged conditions where the sealant will be exposed to strong oxidizers. Avoid submerged conditions where water temperatures will exceed 120 F (50 C). Do not apply over freshly treated wood; treated wood must have weathered for at least 6 months. Substrates such as copper, stainless, and galvanized typically require the use of a primer; Primer 733 or 766 is acceptable. For Kynar 500 based coatings use Primer 733 only. An adhesion test is recommended for any other questionable substrate. UV exposure may cause white NP 1 to discolor. This does not affect sealant performance; where maintaining a true white appearance is critical, use Ultra or Sonolastic 150 sealants. NP 1 can be applied below freezing temperatures only if substrates are completely dry, free of moisture, and clean. Contact Technical Service for more information. Lower temperatures and humidities will extend curing times. Pursuant to accepted industry standards and practices, using rigid paints and/or coatings over flexible sealants can result in a loss of adhesion of the applied paint and/or coating, due to the potential movement of the sealant. However, should painting and/or coating be desired it is required that the applicator of the paint and/or coating conduct on-site testing to determine compatibility and adhesion. Make certain the most current versions of product data sheet and MSDS are being used; call Customer Service ( ) to verify the most current versions. Proper application is the responsibility of the user. Field visits by BASF personnel are for the purpose of making technical recommendations only and not for supervising or providing quality control on the jobsite. Health and Safety NP 1 Warning NP 1 contains Stoddard solvent and crystalline quartz silica. Risks May cause skin, eye or respiratory irritation. May cause dermatitis and allergic responses. Potential skin and/or respiratory sensitizer. Ingestion may cause irritation. Reports associate repeated or prolonged occupational overexposure to solvents with permanent brain, nervous system, liver and kidney damage. INTENTIONAL MISUSE BY DELIBERATELY INHALING THE CONTENTS MAYBE HARMFUL OR FATAL. Precautions Keep container closed. Use only with adequate ventilation. Prevent contact with skin, eyes and clothing. Wash thoroughly after handling. Avoid breathing vapors. DO NOT take internally. Use impervious gloves, eye protection and if the TLV is exceeded or used in a poorly ventilated area, use NIOSH/MSHA approved respiratory protection in accordance with applicable Federal, state and local regulations. First Aid In case of eye contact, flush thoroughly with water for at least 15 minutes. SEEK IMMEDIATE MEDICAL ATTENTION. In case of skin contact, wash affected areas with soap and water. If irritation persists, SEEK MEDICAL ATTENTION. Remove and wash contaminated clothing. If inhalation causes physical discomfort, remove to fresh air. If discomfort persists or any breathing difficulty occurs or if swallowed, SEEK IMMEDIATE MEDICAL ATTENTION. Refer to Material Safety Data Sheet (MSDS) for further information. Proposition 65 This product contains materials listed by the State of California as known to cause cancer, birth defects and other reproductive harm. VOC Content NP 1 contains 43 g/l or 0.36 lbs/gal, less water and exempt solvents. For medical emergencies only, call ChemTrec ( ). BASF Corporation Building Systems 889 Valley Park Drive Shakopee, MN, Customer Service Technical Service LIMITED WARRANTY NOTICE Every reasonable effort is made to apply BASF exacting standards both in the manufacture of our products and in the information which we issue concerning these products and their use. We warrant our products to be of good quality and will replace or, at our election, refund the purchase price of any products proved defective. Satisfactory results depend not only upon quality products, but also upon many factors beyond our control. Therefore, except for such replacement or refund, BASF MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, RESPECTING ITS PRODUCTS, and BASF shall have no other liability with respect thereto. Any claim regarding product defect must be received in writing within one (1) year from the date of shipment. No claim will be considered without such written notice or after the specified time interval. User shall determine the suitability of the products for the intended use and assume all risks and liability in connection therewith. Any authorized change in the printed recommendations concerning the use of our products must bear the signature of the BASF Technical Manager. This information and all further technical advice are based on BASF s present knowledge and experience. However, BASF assumes no liability for providing such information and advice including the extent to which such information and advice may relate to existing third party intellectual property rights, especially patent rights. In particular, BASF disclaims all CONDITIONS AND WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY. BASF SHALL NOT BE RESPONSIBLE FOR CONSEQUENTIAL, INDIRECT OR INCIDENTAL DAMAGES (INCLUDING LOSS OF PROFITS) OF ANY KIND. BASF reserves the right to make any changes according to technological progress or further developments. It is the customer s responsibility and obligation to carefully inspect and test any incoming goods. Performance of the product(s) described herein should be verified by testing and carried out only by qualified experts. It is the sole responsibility of the customer to carry out and arrange for any such testing. Reference to trade names used by other companies is neither a recommendation, nor an endorsement of any product and does not imply that similar products could not be used. For professional use only. Not for sale to or use by the general public. Form No /12 Printed on recycled paper including 10% post-consumer fiber BASF Printed in U.S.A.

64 PRODUCT DATA Joint Sealants CLOSED-CELL BACKER-ROD AND SOFT BACKER-ROD Joint filler and backing material for Sonneborn sealants Description Sonolastic Closed-Cell Backer-Rod is a closed-cell, polyethylene foam jointfiller and backing for elastomeric sealants. Its resilience accommodates dynamic joints. Sonolastic Soft Backer-Rod is a reticulated closed-cell polyethylene foam joint-filler and backing for sealants. It compresses easily to accommodating joints of varying widths. CLOSED-CELL BACKER-ROD Yield See page 3 for chart. Packaging Sizes 1/4 1-1/4" (6 32 mm) are wound on reels and packaged in cartons, weighing about 15 lbs (6.8 kg) per carton. The 1-1/2 4" ( mm) sizes are packaged in 7 ft (2.1 m) lengths and packaged in cartons, weighing about 35 lbs (15.89 kg) per carton. Color Gray Features CLOSED-CELL BACKER-ROD SOFT BACKER-ROD Yield See page 3 for chart. Packaging Sizes 3/8 1-1/8" (10 29 mm) are wound on reels and packaged in cartons, weighing about 15 lbs (6.8 kg) per carton. The 1-1/2 4" ( mm) sizes are packaged in 6 ft (1.8 m) lengths and packaged in cartons, weighing about 18 lbs (8.1 kg) per carton. Color Gray Benefits Closed-cell polyethylene foam Low moisture absorption Lightweight Installs easily and quickly Resilient Accepts joint movement Nonimpregnated, nonstaining, and nonbleeding Will not discolor sealants or substrates Inert Compatible with cold-applied sealants Round Gives proper shape to sealant for effective function Nonadhering to sealants Requires no additional bondbreaker SOFT BACKER-ROD Nongassing when punctured Eliminates bubbling of sealant Reticulated closed-cell polyethylene foam Low moisture absorption Nonimpregnated, nonstaining, and nonbleeding Will not discolor sealants or substrates Highly resilient Conforms to irregular joints; installs easily and quickly Nonadhering to sealants Requires no additional bondbreaker Where to Use APPLICATION Backing for sealants Precast panel joints Expansion joints Window-and door-frame perimeters Coping joints Glazing joints Isolation joints Control joints

65 SONNEBORN PRODUCT DATA CLOSED-CELL BACKER-ROD AND SOFT BACKER-ROD Technical Data CLOSED-CELL BACKER-ROD Composition Closed-Cell Backer-Rod is closed-cell polyethylene foam. Compliances ASTM C 1330, Type C SOFT BACKER-ROD Composition Soft Backer-Rod is reticulated polyethylene foam with a continuous outer skin. Compliances ASTM C 1330, Type B Test Data CLOSED-CELL BACKER-ROD PROPERTY RESULTS TEST METHODS Water absorption, oz/in 3 (g/cc) < (< 0.03) ASTM C 1016 Density, lb/ft 3 (kg/m 3 ) (24 48) ASTM D 1622 Compression recovery, % > 90 ASTM D 5249 Compression deflection, psi (KPa) > 2.97 (>20.5) ASTM D 5249 Tensile strength, psi (KPa) > 29.0 (>200) ASTM D 1623 Service temperature, F ( C) -45 to 160 (-43 to 71) Test results are typical values obtained under laboratory conditions. Reasonable variations can be expected. SOFT BACKER-ROD PROPERTY RESULTS TEST METHODS Water absorption, oz/in 3 (g/cc) (0.10) ASTM C 1016 Density, lb/ft 3 (kg/m 3 ) (24 48) ASTM D 1622 Compression recovery, % > 90 ASTM D 5249 Compression deflection, psi (KPa) > 2.97 (> 20.5) ASTM D 5249 Tensile strength, psi (Kpa) > 29.0 (> 200) ASTM D 1623 Service temperature, F ( C) -45 to 160 (-43 to 71) Test results are typical values obtained under laboratory conditions. Reasonable variations can be expected. How to Apply Application 1. Joint fillers have three major functions: to control the depth of the sealant in proper relation to joint width to provide a backing against which the sealant is applied, forcing the sealant to the sides of the joint to prevent 3-sided bonding, ensuring proper functioning of the joint sealant 2. To install, compress backer-rod into the joint before sealants are applied. 3. Install backer-rod using a blunt probe or a plainfaced roller to force the rod to the desired depth. 4. A template or roller gauge may be used to control the depth at which the rod is placed. 5. DO NOT stretch backer-rod during installation but gently force into the joint so that the backer-rod fits tight against the sides of the joint. Appropriate Backer-Rod Size SIZING CLOSED-CELL BACKER-ROD 1. For joint widths up to 3/4" (19 mm), the diameter of the rod should be 1/8" (3 mm) larger than the width of the joint. 2. For 3/4" (19 mm) wide joints, use 1" (25 mm) diameter rod. SIZING SOFT BACKER-ROD Select a backer-rod diameter that is approximately 25% larger than the width of the joint. See the yield table on the next page for both Closed- Cell and Soft Backer-Rods. Joint sealing 1. Follow suggestions for joint-sealant application as directed by sealant manufacturer. 2. Where priming of the joint is necessary, primer should be applied only to the joint surfaces and allowed to dry before Backer-Rod is placed. DO NOT prime Backer-Rod. For Best Performance Do not puncture, fold, stretch, or crease Closed- Cell Backer-Rod. Follow sealant manufacturer s suggestions for joint sealant width-to-depth ratio. Do not use with hot applied sealants. For joints subject to puncture by high heels or umbrella points, a stiffer or higher density backup material is required. Cork or non-impregnated cane-fiber joint fillers are suitable. Separate materials from the sealant by a nonadhering, bondbreaker (polyethylene tape). Make certain the most current versions of product data sheet and MSDS are being used; call Customer Service ( ) to verify the most current versions. Proper application is the responsibility of the user. Field visits by BASF personnel are for the purpose of making technical recommendations only and not for supervising or providing quality control on the jobsite.

66 SONNEBORN PRODUCT DATA CLOSED-CELL BACKER-ROD AND SOFT BACKER-ROD Yield ESTIMATING CLOSED-CELL BACKER-ROD REQUIREMENTS ROD DIAMETER LINEAR FT PER CARTON IN (MM) (METERS PER CARTON) 1/4 (6) 6,400 (1,951)* 3/8 (10) 3,600 (1,097)** 1/2 (13) 2,500 (762) 5/8 (16) 1,550 (472) 3/4 (19) 1,100 (335) 1 (25) 550 (168) 1-1/4 (32) 400 (122) 1-1/2 (38) 552 (168)*** 2 (51) 360 (110)*** 2-1/2 (64) 240 (73)*** 3 (76) 144 (43.9)*** 4 (102) 90 (27.4)*** * Supplied as two 3,200 ft (975 m) reels ** Supplied as two 1,800 ft (549 m) reels *** Supplied as 7 ft (2.1 m) lengths ESTIMATING SOFT BACKER-ROD REQUIREMENTS ROD DIAMETER IN (MM) LINEAR FT PER CARTON (METERS PER CARTON) 3/8 (10) 3,600 (1097.3)* 5/8 (16) 1,550 (472) 7/8 (22) 850 (259.1) 1-1/8 (29) 500 (152.4) 1-1/2 (38) 552 (168.2)** 2 (51) 360 (109.7)** 2-1/2 (64) 240 (73.2)** 3 (76) 144 (43.9)** 4 (102) 90 (27.4)** * Supplied as two 1,800 ft (549 m) reels ** Supplied as 6 ft (1.8 m) lengths

67 SONNEBORN PRODUCT DATA CLOSED-CELL BACKER-ROD AND SOFT BACKER-ROD BASF Construction Chemicals, LLC Building Systems 889 Valley Park Drive Shakopee, MN, Customer Service Technical Service LIMITED WARRANTY NOTICE Every reasonable effort is made to apply BASF exacting standards both in the manufacture of our products and in the information which we issue concerning these products and their use. We warrant our products to be of good quality and will replace or, at our election, refund the purchase price of any products proved defective. Satisfactory results depend not only upon quality products, but also upon many factors beyond our control. Therefore, except for such replacement or refund, BASF MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, RESPECTING ITS PRODUCTS, and BASF shall have no other liability with respect thereto. Any claim regarding product defect must be received in writing within one (1) year from the date of shipment. No claim will be considered without such written notice or after the specified time interval. User shall determine the suitability of the products for the intended use and assume all risks and liability in connection therewith. Any authorized change in the printed recommendations concerning the use of our products must bear the signature of the BASF Technical Manager. This information and all further technical advice are based on BASF s present knowledge and experience. However, BASF assumes no liability for providing such information and advice including the extent to which such information and advice may relate to existing third party intellectual property rights, especially patent rights. In particular, BASF disclaims all CONDITIONS AND WARRANTIES,WHETHER EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY. BASF SHALL NOT BE RESPONSIBLE FOR CONSEQUENTIAL, INDIRECT OR INCIDENTAL DAMAGES (INCLUDING LOSS OF PROFITS) OF ANY KIND. BASF reserves the right to make any changes according to technological progress or further developments. It is the customer s responsibility and obligation to carefully inspect and test any incoming goods. Performance of the product(s) described herein should be verified bytesting and carried out only by qualified experts. It is the sole responsibility of the customer to carry out and arrange for any such testing. Reference to trade names used by other companies is neither a recommendation, nor an endorsement of any product and does not imply that similar products could not be used. For professional use only. Not for sale to or use by the general public. Form No /07 Printed on recycled paper including 10% post-consumer fiber BASF Printed in U.S.A.

68 Curtainwall Sealant One-Part, Semi-Self-Leveling Sealant Product description Tremco Curtainwall Sealant is a single component, non-drying, non-skinning, synthetic rubber sealant with excellent adhesion. Basic Uses Tremco Curtainwall Sealant is used for sealing concealed metal-to-metal curtainwall joints to prevent air and moisture infiltration. Use as a bedding for panels, sheets, rails, moldings, and other types of metal-to-metal sleeves or connections to aluminum window wall and curtainwall systems. Availability Tremco Curtainwall Sealant is immediately available through your local Tremco field representative(s) or Tremco distributors throughout the United States, Canada, and overseas. Coverage Rates 35 linear feet of joint per 10.1 oz (300mL) cartridge for a 1/4 X 1/4 joint. For specific coverage rates that include joint size, and usage efficiencies, visit our website usage calculator at tremcosealants.com Features and Benefits The application of Tremco Curtainwall Sealant greatly reduces the air and moisture permeation as well as reduces energy loss around the perimeter of the curtainwall. Packaging 10.1 fl. oz. (300mL) cartridges Color Dark Gray Surface preparations For good adhesion, the joint interface must be sound, clean, and dry. Any surface damage, dirt, dust, loose particles or other contaminants, which may inhibit adhesion, must be removed from the surfaces prior to the application of the sealant. Priming Priming is not required. TYPICAL PHYSICAL PROPERTIES These physical properties are published as general information only. The listed properties and performance characteristics are approximate values and are not part of the product specification. Viscosity (Flow meter) Aging Accelerated Aging Flexibility Staining Gunnability 40 seconds (20g at 40 psi at 77 F or 25 C) Firm but rubbery and elastic set, good tack at room temperature after 52 days of conditioning at 158 F (70 C). Firm but rubbery and elastic set, excellent adhesion, and no significant change in characteristics after 960 hours in weatherometer. 1/8 round bead on aluminum surface aged 2 days at 75 F (24 C), then subjected to: 1) 3 weeks at 75 F (24 C) 2) 24 weeks at -40 F (-40 C) 3) 3 weeks at 158 F (70 C) After conditioning, samples were bent over 1/4 mandrel in 180 arc with no cracking or splitting. Non-staining Satisfactory at 30 F (-1 C) through 3/8 round nozzle. Solids Content: Approximately 90% Weight/gallon: Hardness: Oil Migration: lbs./gallon scale A 12, scale (after 2 months heat age) Does not exude oil when applied between bolted metal panels allowing 1/16 seal and assembly conditioned for three weeks at 158ºF (70ºC) Page 1 of 2

69 Application Tremco Curtainwall Sealant is used in the design and construction of curtainwall partitions in commercial units. Sealant is easy to apply with conventional caulking equipment. Apply bead as a bedding for panels, rails, and other types of metal-to-metal sleeves or connections to aluminum window wall and curtainwall systems. Cure Time Curtainwall Sealant does not cure. It is a non-skinning, nondrying sealant. Clean up Excess sealant and smears adjacent to the joint interface can be carefully removed with xylene or mineral spirits before the sealant cures. Any utensils used for tooling can also be cleaned with xylene or mineral spirits. Limitations Do not apply over damp or contaminated surfaces. Use with adequate ventilation. Warranty Tremco warrants its sealants to be free of defects in materials, but makes no warranty as to appearance or color. Since methods of application and on-site conditions are beyond our control and can affect performance, Tremco makes no other warranty, expressed or implied including warranties of MERCHANTABILITY and FITNESS FOR A PARTICULAR PURPOSE, with respect to Tremco sealants. Tremco s sole obligation shall be, at its option, to replace, or refund the purchase of the quantity of Tremco sealant proven to be defective and Tremco shall not be liable for any loss or damage. Tremco Commercial Sealants & Waterproofing 3735 Green Road, Beachwood, OH // Phone: // Wicksteed Avenue, Toronto, ON M4H 1G7 // Phone: // Jacobson Avenue, Ashland OH // Phone: // /CS Page 1 of 1

70 BUILD WITH LIGHT Superneutral Series SuperNeutral 54 MORE NATURAL LIGHT. LESS HEAT GAIN. GREATER ENERGY SAVINGS. SunGuard SuperNeutral 54 improves glass energy performance by up to 30% compared to current commercial building energy standards 1. 1 ANSI/ASHRAE/IESNA Standard Photo for demonstration purposes only. New SuperNeutral 54 strikes the perfect balance g High visible light transmission (54%) g g g g g g g Less glare transmitted to the interior compared to other leading products Neutral outdoor appearance Best in class 95 CRI (color rendering index) so light s true colors always show through Excellent solar control (0.28 SHGC) Thousands of dollars in potential energy savings Helps projects qualify for LEED credits Available nationwide through Guardian s independent network of Select Fabricator s to meet tight project deadlines SunGuard, Build With Light, SuperNeutral and CrystalGray are registered trademarks of Guardian Industries Corp Guardian Industries Corp. To learn more, call us at GuardSG ( ) or visit us online

71 SUPERNEUTRAL 54 PERFORMANCE DATA INSULATING GLASS UNITS Appearance Product Outboard Substrate Inboard Substrate Visible Light % Transmission Reflectance U-Value Ultraviolet % Solar Energy % SunGuard SuperNeutral 54 Coating #2 Surface 6 mm / 12 mm a.s. / 6 mm Visible Light Out % Visible Light In % Solar Energy Out % Winter Nighttime Summer Daytime Relative Heat Gain Shading Coefficient Solar Heat Gain Coefficient Light to Solar Gain (LSG) Ultra Clear SN 54 UltraWhite UltraWhite Clear SN 54 Clear Clear Green SN 54 Green Clear Light Gray SN 54 CrystalGray Clear NOTES: The performance values shown are nominal and subject to variations due to manufacturing tolerances. Guardian performance data are calculated in accordance with the LBNL Window 5.2 computer analysis using an air mass of 1.5. Outboard lite may require heat strengthening or tempering to resist potential thermal stresses. Please contact Guardian for assistance. A slight shift in visible light reflectance or transmission may be noticed after heat-treatment. Guardian recommends edge deletion for all low-e coatings. Guardian reserves the right to change product performance characteristics without notice or obligation. TO REQUEST SAMPLES visit SunGuardGlass.com or call GuardSG

72 PERFORMANCE CALCULATOR July 18, 2013 Prepared for Submittal By Henson, Kevin David Anthony MS 18 Make-up Name Makeup Outboard Substrate & Coating Visible Light % Transmission Reflectance U-Value UV % Solar Energy % Visible Out % Visible In % Solar Energy Out % Winter Night (Btu/hr-ft²- F) Summer Day (Btu/hr-ft²- F) RHG (Btu/h r-ft²) SC SHGC LSG G1 Clear G4 G5 G7 Guardian SunGuard SuperNeutral 54 on Green Warm Gray Frit 100% Full Coverage on Clear_ Guardian SunGuard SuperNeutral 54 on Green G8 Clear G8G Clear Calculation Standard: NFRC 2010 G1 LITE Clear Thickness = 1/4" = 6mm Outdoors # # Total Unit = in / mm Slope = 90 Indoors Thermal Stress Guideline ( F) Go 97.6 G4 LITE Green Thickness = 1/4" = 6mm Outdoors # #2 Guardian SunGuard SuperNeutral 54 Thermal Stress Guideline ( F) Stop GAP 100% Air, 1/2" = 12mm LITE Clear Thickness = 1/4" = 6mm # # Total Unit = in / mm Slope = 90 Indoors Go 99.0 SunGuard is a registered trademark of Guardian Industries Corp. Page 1 of 3

73 PERFORMANCE CALCULATOR G5 LITE Clear_ Thickness = 1/4" = 6mm Outdoors Total Unit = in / mm Slope = 90 Indoors # #2 Warm Gray Frit 100% Full Coverage Thermal Stress Guideline ( F) Go G7 LITE Green Thickness = 1/4" = 6mm Outdoors # #2 Guardian SunGuard SuperNeutral 54 Thermal Stress Guideline ( F) Stop GAP 100% Air, 1/2" = 12mm LITE PVB LITE Clear Thickness = 1/8" = 3mm 0.030" Saflex Clear PVB Clear Thickness = 1/8" = 3mm # # # # Total Unit = in / mm Slope = 90 Indoors Go Go 99.5 G8 LITE PVB LITE Clear Thickness = 1/8" = 3mm 0.030" Saflex Clear PVB Clear Thickness = 1/8" = 3mm Outdoors # # # # Total Unit = in / mm Slope = 90 Indoors Thermal Stress Guideline ( F) Go Go G8G LITE PVB LITE Clear Thickness = 1/8" = 3mm 0.030" Graphic Design by Architect Clear Thickness = 1/8" = 3mm Outdoors # # # # Total Unit = in / mm Slope = 90 Indoors Thermal Stress Guideline ( F) Go Go SunGuard is a registered trademark of Guardian Industries Corp. Page 2 of 3

74 PERFORMANCE CALCULATOR Important Notes Calculations and terms in this report are based on NFRC The performance values shown above represent NOMINAL VALUES for the center of glass with no spacer system or framing. Slight variations may occur due to manufacturing tolerances, point of manufacture, and type of instrumentation used to measure the optical properties. For configurations which include ceramic frit coating, the actual values may vary significantly based upon the thickness and composition of the frit. For configurations with diffuse optical properties the solar transmission is per ASTM For configurations with coatings laminated facing the PVB, there may be a noticeable color change. Guardian recommends that a full size mock-up be approved. Please note that the THERMAL STRESS GUIDELINE is only a rough reference to the thermal safety of a glazing. Other factors such as the size of glass areas, shapes and patterns, glass thickness, glass damaged during shipping, handling or installation, orientation of the building, exterior shading, overhangs/fins that reduce wind speed, and areas with high daily temperature fluctuations can all increase the probability of thermal breakage. The results shown are not for any specific glazing installation and do not constitute a warranty against glass breakage. Explanation of Terms % Transmittance Visible is the percentage of visible light at normal incidence (90 to surface) directly transmitted through the glass. Visible Light is defined as radiant energy in the wavelength range of 380 nm to 780 nm with Ill. D65 and CIE 2 observer % Ultraviolet (UV) Transmittance is the percentage of ultraviolet light at normal incidence (90 to surface) directly transmitted through the glass. Ultraviolet Light is defined as radiant energy from the sun having a wavelength range of 300 nm to 380 nm at ASTM air mass of 1.5 % Solar Energy Direct Transmittance is the percentage of solar energy at normal incidence (90 to surface) directly transmitted through the glass. Solar Energy is the radiant energy from the sun having a wavelength range of 300 nm to 2500 nm at ASTM air mass of 1.5. % Reflectance Visible Outdoors is the percentage of visible light at normal incidence directly reflected from the glass back outdoors % Reflectance Visible Indoors is the percentage of visible light at normal incidence directly reflected from the glass back indoors % Solar Energy Reflected Outdoors is the percentage of solar energy at normal incidence directly reflected from the glass back outdoors U-Factor (also called U-Value) is the air-to-air thermal conductance of 39" high glazing and associated air films. Units are Btu/hr.ft².F. Winter-night = 12.3 mph wind at -0.4 F outdoors and 69.8 F still (no forced convection) indoor air. Summer = 0 sun, 6.15 mph wind at 89.6 F outdoors and 75.2 F still (no forced convection) indoor air. Relative Heat Gain (RHG) is the total net heat gain to the indoors due to both the air-to-air thermal conductance and the solar heat gain. The units are Btu/hr.ft². RHG = [(Summer U-Value)(89.6 F F) + (Shading Coefficient)(200 Btu/hr-ft²)] Shading Coefficient (SC) is the fraction of solar heat, direct (300 to 2500 nm) plus indirect (5 to 40 µm), transferred indoors through the glass. For reference, 1/8" (3.1 mm) clear glass has a value of 1.00 (SC is an older term being replaced by the SHGC). Solar Heat Gain Coefficient (SHGC) is the fraction of solar energy incident on the glazing that is transferred indoors both directly and indirectly through the glazing. The direct gain portion equals the direct solar transmittance, while the indirect is the fraction of the solar energy absorbed to the energy reradiated and convected indoors. No heat gain from warmer outdoor air is included. SHGC = (Direct Solar Trans) + {[(Indirect Solar Heat Gain) - (Summer U-Value)(89.6 F F)] / ( Btu/hr-ft²)} Light-to-Solar Gain (LSG) is the ratio of visible light gain to solar gain. LSG = (Visible Transmittance) / (SHGC) This performance analysis is provided under license by Guardian Industries Corp. It is designed to assist the user in evaluating the performance of the glass products identified on this report. Many factors may affect glass performance including glass size, building orientation, shading, wind speed, type of installation, and other factors. With respect to non-guardian products, this performance analysis may be based on published information from the manufacturer that has not been independently verified by Guardian for accuracy. The applicability and results of the analysis are directly related to user inputs and any changes in actual conditions can have a significant affect on the results. While Guardian has made a good faith effort to verify the reliability of this program, it may contain unknown programming errors that could result in incorrect results. GUARDIAN DOES NOT PROVIDE ANY WARRANTY OR GUARANTEE REGARDING THE ACCURACY OF THE INFORMATION IN THIS REPORT OR AGAINST GLASS BREAKAGE OR FOR ANY DIRECT OR INDIRECT DAMAGES THAT MAY BE DUE TO THE USE OF THE PROGRAM. SunGuard is a registered trademark of Guardian Industries Corp. Page 3 of 3

75 80 Series Standard & 180/181 Series Bracket System REGULAR-DUTY Up to 320 lbs./pair* Single slot design Adjustable in 1" increments Applications For storage and display applications in retail stores, grocery stores, light warehouses, light industrial, repair garages, maintenance storage, business office storage, and residential storage. Load Rating: Varies per size* Mounting: Wall Material: 14- and 16-Gauge Steel Construction Finishes: Almond (ALM), Anochrome (ANO), Black (BLK), Brown (BRN), Brass-look (BR), Titanium (TI), White (WH): Attractive, long-lasting, corrosion resistant finishes Compliant: Almond (ALM), Anochrome (ANO), Black (BLK), Brown (BRN), Titanium (TI), White (WH) Features: Standards can be mounted to most any type of wall. 80 Series Standards and 180/181 Series Brackets offer the widest range of color and sizes of all KV shelving systems. Reinforced brackets lock into slotted standards for strong, secure, weight-bearing support. Brackets are vertically adjustable in 1" increments. 80 Series Standards Dimension: 5/8" wide x 13/32" deep x selected length 16-gauge steel construction Made in the USA Available from open stock 180 Series Brackets 16-gauge steel construction: 4"- 12" brackets 14-gauge steel construction: 14" - 20" brackets Vertically adjustable in 1" increments Made in the USA Available from open stock 181 Series Brackets Lip-less version of 180 Bracket 16-gauge steel construction For use with any 1" KV adjustable standards Made in the USA Available from open stock * Consult KV Customer Service for information. Knape & Vogt, 2700 Oak Industrial Drive NE, Grand Rapids, MI USA P F

76 80 Series Standard & 180/181 Series Bracket System 80 Series Standards Standard Pack (10/Box, screws not included. UPC label attached.) Size Almond Anochrome Black Brown Brass-look Titanium White (ALM) (ANO) (BLK) (BN) (BR) (TI) (WH) 12" 80 ALM ANO BLK BN BR TI WH 12 24" 80 ALM ANO BLK BN BR TI WH 24 36" 80 ALM ANO BLK BN BR TI WH 36 48" 80 ALM ANO BLK BN BR TI WH 48 60" 80 ALM ANO BLK BN BR TI WH 60 72" 80 ALM ANO BLK BN BR TI WH 72 96" 80 ALM ANO BLK BN BR TI WH 96 Builders Pack (BP) (25/Box, no UPC labels) Size Anochrome (ANO) 12" 80BP ANO 12 24" 80BP ANO 24 36" 80BP ANO 36 48" 80BP ANO 48 60" 80BP ANO 60 72" 80BP ANO 72 96" 80BP ANO 96 Titanium (TI) Almond (ALM) Anochrome (ANO) Black (BLK) Brown (BN) Brass-look (BR) White (WH) Screws & Anchors Display Pack (DP) (20 poly bags/carton. Each poly bag contains 6 screws and 6 screw anchors.) Almond (ALM) Anochrome (ANO) Black (BLK) Brass-look (BR) Brown (BN) Titanium (TI) White (WH) 80-88DP ALM 80-88DP ANO 80-88DP BLK 80-88DP BR 80-88DP BN 80-88DP TI 80-88DP WH Warehouse Pack (WP) (50 poly bags/carton. Each poly bag contains 6 screws and 6 screw anchors.) Almond (ALM) Anochrome (ANO) Black (BLK) Brass-look (BR) Brown (BN) White (WH) 80-88WP ALM 80-88WP ANO 80-88WP BLK 80-88WP BR 80-88WP BN 80-88WP WH Head: #6 Body: #8 Length: 1-1/2" Standard Pack (50 screws per bag, no anchors) Almond (ALM) Black (BLK) Brass-look (BR) White (WH) Zinc (ZC) ALM BLK BR WH ZC Builders Pack (6,000 bulk screws/carton) Almond (ALM) Black (BLK) Brass-look (BR) Titanium (TI) White (WH) Zinc (ZC) ALM BLK BR WH ZC Knape & Vogt, 2700 Oak Industrial Drive NE, Grand Rapids, MI USA P F